Search Results

Search found 5290 results on 212 pages for 'refresh rate'.

Page 52/212 | < Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >

• RAID Array performance on an HP Proliant ML350 G5 Smart Array E200i

  - by Nate Pinchot

  We have a client who is complaining about performance of an application which utilizes an MS SQL database. They do not believe the performance issues are the fault of the application itself. The Smart Array E200i RAID controller has 128MB cache and we have the cache set to 75% read/25% write. The disk array set to enable write caching. Recently we ran a disk performance test using SQLIO based on this guide. We used a 10 GB file for the test found that the average sequential read rate was ~60 MB/sec (megabytes/sec) and the average random read rate was ~30 MB/sec. Are these numbers on par for what the server should be performing? Better than on par? Horrible? Amazing?

  Read the article

• Chrome browser caching

  - by Kyle B.

  I do a lot of development on my local machine and would like to start using Chrome, however I cannot seem to do a hard-refresh (ctrl+f5) or any other key combination to get my browser to forcibly refresh all content @ http://localhost. I change projects frequently in IIS and this presents a problem because I see stylesheet and image data from my previous project with no way to get this page to reload without forcibly dumping all cache data from the settings menu. Is there another key combination I am missing, or is there a place I can (on a site by site basis) turn off caching? I prefer not to have to clear out my temporary files in the browser settings as I switch projects frequently. Thanks, Kyle

  Read the article

• Windows 8 slow after refreshing and rebooting

  - by Dan Drews

  First, I apologize if this is in the wrong place. I use S/O a lot but not the other sites much. I have an HP Split X2 that has been very choppy as of late (takes several seconds to respond to any form of input), so I went ahead and did a system refresh. After the refresh everything ran very fast as it should, then when I went to download my old apps I needed to reboot. After rebooting, it went back to the choppiness. Does anybody have any thoughts on what this could be?

  Read the article

• Why is my firewall preventing me from accessing some websites

  - by nosx

  I have an old Belkin router and when I enable the firewall I cannot access certain websites. For example: http://www.avisynth.org With Firewall Enabled: Main page loads and begins to do a meta refresh which never finishes. With Firewall Disabled: Main page loads and the meta refresh completes as normal and I am taken to the wiki page. I have not setup any rules in my firewall that would prevent this site from loading, yet it refuses to load unless I have the firewall disabled completely. My router has a hidden page with advanced settings on it for the firewall which I was able to acccess and take a screenshot of, but I did not want to mess with these values unless I absolutely have to do so: What might be causing this problem and how would I go about fixing it?

  Read the article

• Slow internet using Arch Linux

  - by GZaidman

  after a week or so of using Arch Linux I cant access the internet - it takes around 5 mins to load google (most of the other websites just give me a timeout), pacman's downloading speed range between 5-2Kbs, and pinging google takes around 9Kms. I'm connected using wireless network (wifi card is Intel Ultimate 6300 and router is Edimax 6524n). Every other Windows machine that's connected to the network (and even the T410 running Windows) is fine, so the problem lies in Linux. So far, i checked the resolv.conf file (my router ip address is listed), and the hosts file (pretty much default), and I disabled the ipv6 module. None of that helped. PS: i'm using NetworkManager (but the problem still occurs when connecting using wicd) running on Gnome3. Thanks in advance for any help you can provide! EDIT: something really strange happens whenever I ping google: i get an unknown host 'google.com', but the bit rate from the card jumps at the exact second I ping google (so far, the bit rate jumped to 54Mb/s from 1Mb/s over the course of 4 pings).

  Read the article

• Mysterious winamp ratings that come from nowhere

  - by Phenom

  Winamp gives the option to rate songs. This is not a new feature. Everytime I would reinstall Windows and reinstall Winamp my ratings would all go away as expected, and I would have to re-rate everything. However, this time when I reinstalled Winamp, after using it for a few days, songs would appear in my top rated list as being rated. Some of these I remember rating a long time ago before I reinstalled Windows, and some of these I don't remember ever rating. Where are these ratings coming from?

  Read the article

• Probability of failure with larger number of network elements

  - by MikeKulls

  I'm having a discussion with a work colleague. I'm saying that a network with 100 elements will have pretty much 10 times as many failures as a network with 10 elements, ie a tech will need to replace faulty hardware 10 times more often. He suggests that the failure rate doesn't go up in a linear fashion and the failure rate will be significantly less than 10x, in fact only slightly more failures. This is not the probability of an outage etc, we are just talking in relation to the amount of parts that a tech would need to swap out in a given time frame.

  Read the article

• Add Mirror for volumes other than the last one in Windows 7 (disk "not up-to-date")

  - by rakslice

  I'm using Windows 7 x64 Ultimate. I have an existing 4TB disk with 3 NTFS volumes, a new 3TB blank disk, and I'm trying to mirror the volumes onto the new disk. My Windows install is on an SSD which is Disk 0. The 4TB disk with volumes is Disk 1, and the new blank disk is Disk 2. I can add a mirror successfully for the last volume, but when I try to add a mirror for the first volume I immediately get errors (see below). Is there something I special I need to do to add a mirror for a volume other than the last one? More info: I opened Disk Management, right-clicked on the first volume on the existing disk, went to Add Mirror, and selected the new disk. The first time I did this I was prompted to convert the new disk to a Dynamic Disk, which I approved. Subsequently I got a message: The operation failed to complete because the Disk Management console view is not up-to-date. Refresh the view by using the refresh task. If the problem persists close the Disk Management console, then restart Disk Management or restart the computer. I've refreshed disk management, restarted the computer, and converted the new disk to basic and back to dynamic, but I still get that error message. Looking around for suggestions of a workaround, I saw a suggestion to use the diskpart command line tool. Running diskpart from the Start Menu as Administrator, I did select volume 2 (the first volume I want to mirror) and then add disk 2 (the new disk), and received a somewhat similar error: Virtual Disk Service error: The disk's extent information is corrupted. DiskPart has referenced an object which is not up-to-date. Refresh the object by using the RESCAN command. If the problem persists exit DiskPart, then restart DiskPart or restart the computer. A rescan appears to be successful: DISKPART> select disk 2 Disk 2 is now the selected disk. DISKPART> rescan Please wait while DiskPart scans your configuration... DiskPart has finished scanning your configuration. but attempting to add the mirror again resulted in the same error. The only similar report I found online was this: http://www.sevenforums.com/hardware-devices/335780-unable-mirror-all-but-last-partition-drive.html Based on that I attempted to mirror the last volume on the disk to the new disk using diskpart, and that started successfully -- it is currently resynchronizing. More Background: In the course of dealing with a failing 3TB hard drive, I bought a replacement 4TB drive and installed it, then copied the partitions from the failing drive to it using Minitool Partition Wizard Home, and then removed the failing drive and was up and running again normally. Now I've received a warranty replacement for the failing drive, and installed it, and now I'm attempting to mirror my partitions to it.

  Read the article

• Is to possible to achieve the SATA II's 3Gbps (375MBps) between home network storage and home computers?

  - by techaddict

  Gigabit ethernet only has 1Gbps (125MBps), whereas SATA II has up to three times that rate. Is it possible to achieve the rate of three times Gigabit ethernet connection which is SATA II speeds, between home network storage and the laptops and desktops with SATA II hard drives? If so, how? Or, is the limitation of a gigabit ethernet port on the laptops the limitng factor, making 1000Gbps the fastest practical transfer speed possible? (practical, meaning that without taking apart the laptop and doing physical modifications like branching a SATA II transfer cable, etc.) -- I just realized -- wouldn't a USB 3.0 cable do the trick? Since USB 3.0 can reach up to 675MBps?

  Read the article

• How to diagnose very slow pagefile

  - by svick

  Quite often, one of the applications I use freezes (“does not respond”) for a while, in extreme cases for few minutes. This happens especially when when switching apps. During this time, the HDD light flashes constantly and perfmon show that HDD is used 100% of the time (OTOH, CPU isn't) and that pagefile is being read (which is to be expected when switching apps), but at a very slow rate. When I sort the disk table in perfmon by read or write, the file read and wrote the most is the pagefile, but it's still quite low rate (I don't remember the numbers). How can I diagnose what's causing this? I use Windows Vista, and the computer is quite ordinary two years old laptop.

  Read the article

• Web-based interface is mangled

  - by justSteve

  Linksys WRT54 - over the last couple days i've been in and out of network configuration screens of my DSL modem and the router (and the commandline for that matter) as I've installed the DynDNS service. (thankx to subsonic and DynDNS.com i'm now able to stream my workstations MP3 catalog over my wife's Droid - making me her tech hero all over again) Somewhere after getting all the net ducks lined up - ports forwarded and firewalls configured - the web-interface for the router ceased rendering the full page - it's only rendering parts, i can F5/refresh and it re-renders and displays some of the cells (table-based webpage) but omits others that _had rendered before the refresh. Happens for both IE and FF. And continues after a reboot. Probably need to re-cycle the router itself but is this known behavior or should i look deeper for a cause? thx

  Read the article

• Taskbar Network "Repair" menu option gone in Windows 7

  - by JohnB

  I used to LOVE that feature in Windows XP! Just right-clicked on the WiFi icon on the Taskbar (lower right-hand corner), then Repair. It doesn't take that long, and it usually helped me since I constantly go back and forth between LAN at work, VPN on WiFi from work and home, and also VPN to my own personal server. Even if you didn't need to refresh, doing so never hurts! Unfortunately, the feature seems to be removed from Win7 :( Now you can check for problems, but it only does the refresh if it thinks it needs too, and the whole process tasks so darn long! Is there a way to Repair my WiFi connection quickly and easily on Win7?

  Read the article

• Cisco IOS ACL types

  - by cjavapro

  The built in command help list displays access list types based on which range. router1(config)#access-list ? <1-99> IP standard access list <100-199> IP extended access list <1100-1199> Extended 48-bit MAC address access list <1300-1999> IP standard access list (expanded range) <200-299> Protocol type-code access list <2000-2699> IP extended access list (expanded range) <700-799> 48-bit MAC address access list dynamic-extended Extend the dynamic ACL absolute timer rate-limit Simple rate-limit specific access list router1(config)# What are each of the types? Can multiple types of ACLs be applied to a given interface?

  Read the article

• How can I shrink the Address toolbar in the Task Bar?

  - by Iszi

  I like being able to run commands straight from my Task Bar. So, I've enabled the Address toolbar on my new Windows 7 system - just like I had on my old XP system. However, the bar seems to have a mandatory minimum length that's a bit longer than I'd prefer. It's about twice as long, if memory serves, as the minimum size allowed in XP. Is there any way I can adjust this minimum length, through a Registry key or some other means? (Note: I've also got a related question, about removing the Refresh button at the end of the bar.) EDIT: For clarity, I'm adding a screenshot. The toolbar I want to shorten is the one circled below, with an empty text-entry field that has a drop-down and "Refresh" button. I currently have it positioned between a Quick Launch toolbar and the Taskbar. On the far side of the Taskbar, before the System Tray, is a Desktop toolbar.

  Read the article

• Determining Performance Limits

  - by JeffV

  I have a number of windows processes that pass messages between them hat a high rate using tcp to local host. Aside from testing on actual hardware how can I assess what my hardware limit will be. These applications are not doing CPU intensive work, mostly decomposing and combining messages, scanning over them for special flag in the data etc.. The message size is typically 3k and the rate is typically ~10k messages per second. ~30MB per second between processing stages. There may be 10 or more stages depending. For this type of application, what should I look to for assessing performance? What do I look for in a server performance wise? I am currently running an XEON L5408 with 32 GB ram. But I am assuming cache is more important than actual ram size as I am barely touching the ram.

  Read the article

• 802.11 Capture Frame

  - by ALi

  I am using wireshark in monitor mode to capture all the frame. I buffered all the QosData in order to calculate the biterate of each station on the network. I calculate the biterate but it is not an accurate value. what i need to know is when the station use the network alone and when it uses it with another station? i know if two station with different wifi card for exemple ( st1 802.11g 54 Mb/s, st2 802.11n 300 Mb/s) if st1 uses alone the line the biterate used is 28 MB/s and if st2 uses alone the network the bit rate increase to approximately 150Mb/s but if the two station use the network at the same time the st1 lost about 80% of its bit rate because of the st1 wifi card thx in advance

  Read the article

• ffmpeg add two audio streams to video

  - by Tossin Hausen

  I tried this: ffmpeg -i /sdcard/video/transcode/video.avi -map 0:0,0 -i /sdcard/video/transcode/first.mp3 -map 1:0,1 -i /sdcard/video/transcode/second.mp3 -map 2:0,2 -acodec copy -vcodec py /sdcard/video/transcode/Output.avi to add two audio streams to one video file. But ffmpeg says the number of mappings should match the number of output streams. What is wrong here? I'm trying to work with an Android build of FFmepg "ffmpeg for android beta". "Does not work" means that this uncommunicative Android build of FFmpeg just stops without giving any error message. The -codec copy option does not work with this build. Now I tried the same set of files with the FFmpeg called command line tool that comes with Ubuntu 10. Something (can't say where it is from). The -codec copy option does not work with this FFmpeg too. Here the complete output: m30x:~/movie/Film$ ffmpeg -i input.avi -i first.mp3 -i second.mp3 -map 0 -map 1 -map 2 -acodec copy -vcodec copy output.avi FFmpeg version SVN-r0.5.9-4:0.5.9-0ubuntu0.10.04.1, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --extra-version=4:0.5.9-0ubuntu0.10.04.1 --prefix=/usr --enable-avfilter --enable-avfilter-lavf --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --disable-stripping --disable-vhook --enable-runtime-cpudetect --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --enable-shared --disable-static libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 1 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 libswscale 0. 7. 1 / 0. 7. 1 libpostproc 51. 2. 0 / 51. 2. 0 built on Jun 12 2012 16:27:34, gcc: 4.4.3 [NULL @ 0x93cfd10]looks like this file was encoded with (divx4/(old)xvid/opendivx) -> forcing low_delay flag Seems stream 0 codec frame rate differs from container frame rate: 30000.00 (30000/1) -> 25.00 (25/1) Input #0, avi, from 'input.avi': Duration: 01:30:33.00, start: 0.000000, bitrate: 901 kb/s Stream #0.0: Video: mpeg4, yuv420p, 576x432, 25 tbr, 25 tbn, 30k tbc Input #1, mp3, from 'first.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #1.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Input #2, mp3, from 'second.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #2.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Number of stream maps must match number of output streams Merging only one audio stream with the video stream works with Ubuntu and Android version of FFmpeg. Here the complete output: ffmpeg -i input.avi -i first.mp3 -map 0 -map 1 -acodec copy -vcodec copy output.avi FFmpeg version SVN-r0.5.9-4:0.5.9-0ubuntu0.10.04.1, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --extra-version=4:0.5.9-0ubuntu0.10.04.1 --prefix=/usr --enable-avfilter --enable-avfilter-lavf --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --disable-stripping --disable-vhook --enable-runtime-cpudetect --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --enable-shared --disable-static libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 1 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 libswscale 0. 7. 1 / 0. 7. 1 libpostproc 51. 2. 0 / 51. 2. 0 built on Jun 12 2012 16:27:34, gcc: 4.4.3 [NULL @ 0x9bfad10]looks like this file was encoded with (divx4/(old)xvid/opendivx) -> forcing low_delay flag Seems stream 0 codec frame rate differs from container frame rate: 30000.00 (30000/1) -> 25.00 (25/1) Input #0, avi, from 'input.avi': Duration: 01:30:33.00, start: 0.000000, bitrate: 901 kb/s Stream #0.0: Video: mpeg4, yuv420p, 576x432, 25 tbr, 25 tbn, 30k tbc Input #1, mp3, from 'first.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #1.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Output #0, avi, to 'output.avi': Stream #0.0: Video: mpeg4, yuv420p, 576x432, q=2-31, 90k tbn, 25 tbc Stream #0.1: Audio: libmp3lame, 22050 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #1.0 -> #0.1 Press [q] to stop encoding frame= 6157 fps=6156 q=-1.0 size= 31667kB time=246.28 bitrate=1053.3kbits/s Do you have an idea why it does not work with two audio streams? By the way, ffmpeg -i input_with_first_audio_stream.avi -i second.mp3 -acodec copy -vcodec copy output_two_audio_streams.avi -newaudio works with both versions of ffmpeg that I use, but the first audio stream is played too fast (x10 or more), while the second audio stream is played correct. Many thanks in advance and sorry for my unconventional question and outdated versions of ffmpeg. But I am a lamer and it is not so easy for me to compile from the source (especially for the Android version). I will try to compile an up to date version of ffmpeg with Ubuntu, but I don't have much free time.

  Read the article

• Simulating a low-bandwidth, high-latency network connection on Linux

  - by Justin L.

  I'd like to simulate a high-latency, low-bandwidth network connection on my Linux machine. Limiting bandwidth has been discussed before, e.g. here, but I can't find any posts which address limiting both bandwidth and latency. I can get either high latency or low bandwidth using tc. But I haven't been able to combine these into a single connection. In particular, the example rate control script here doesn't work for me: # tc qdisc add dev lo root handle 1:0 netem delay 100ms # tc qdisc add dev lo parent 1:1 handle 10: tbf rate 256kbit buffer 1600 limit 3000 RTNETLINK answers: Operation not supported How can I create a low-bandwidth, high-latency connection, using tc or any other readily-available tool?

  Read the article

• php-fpm or nginx: bad gateway

  - by John Tate

  I'm getting a bad gateway error all the sudden for a site. I didn't change the configuration for the site, I just added a new server config where I put them under /etc/nginx/servers and it stopped working. The new server works, and there is no conflict between the php-fpm listen addresses. server { listen 80; server_name obfuscated.onion; location = / { root /var/www/sites/obfuse; index index.php; } location / { root /var/www/sites/obfuse; index index.php; if (!-f $request_filename) { rewrite ^(.*)$ /index.php?q=$1 last; break; } if (!-d $request_filename) { rewrite ^(.*)$ /index.php?q=$1 last; break; } } error_page 404 /index.php; location ~* ^.+.(jpg|jpeg|gif|css|png|js|ico)$ { root /var/www/sites/obfuse; access_log off; expires 30d; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www/sites/obfuse$fastcgi_script_name; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param PATH_INFO $fastcgi_script_name; include fastcgi_params; } } There is nothing unusual in php-fpm's log even when I raised the level to debug. [24-Jun-2013 09:10:37.357943] DEBUG: pid 6756, fpm_scoreboard_init_main(), line 40: got clock tick '100' [24-Jun-2013 09:10:37.358950] DEBUG: pid 6756, fpm_event_init_main(), line 333: event module is kqueue and 1 fds have been reserved [24-Jun-2013 09:10:37.358978] NOTICE: pid 6756, fpm_init(), line 83: fpm is running, pid 6756 [24-Jun-2013 09:10:37.359009] DEBUG: pid 6756, main(), line 1832: Sending "1" (OK) to parent via fd=5 [24-Jun-2013 09:10:37.389215] DEBUG: pid 6756, fpm_children_make(), line 421: [pool cyruserv] child 22288 started [24-Jun-2013 09:10:37.391343] DEBUG: pid 6756, fpm_children_make(), line 421: [pool cyruserv] child 21911 started [24-Jun-2013 09:10:37.391914] DEBUG: pid 6756, fpm_event_loop(), line 362: 5776 bytes have been reserved in SHM [24-Jun-2013 09:10:37.391941] NOTICE: pid 6756, fpm_event_loop(), line 363: ready to handle connections [24-Jun-2013 09:10:38.393048] DEBUG: pid 6756, fpm_pctl_perform_idle_server_maintenance(), line 379: [pool cyruserv] currently 0 active children, 2 spare children, 2 running children. Spawning rate 1 [24-Jun-2013 09:10:39.403032] DEBUG: pid 6756, fpm_pctl_perform_idle_server_maintenance(), line 379: [pool cyruserv] currently 0 active children, 2 spare children, 2 running children. Spawning rate 1 [24-Jun-2013 09:10:40.413070] DEBUG: pid 6756, fpm_pctl_perform_idle_server_maintenance(), line 379: [pool cyruserv] currently 0 active children, 2 spare children, 2 running children. Spawning rate 1 I don't know why this has started happening, but the logs are not telling me anything. Please ask for more information than this, you'll probably need it.

  Read the article

• how to record mic input and pipe the output to another program

  - by acrs

  Hi everyone Im trying to follow a tutorial on generating truly random bits How To Generate Truly Random Bits This is the command from the tutorial but it does not work rec -c 1 -d /dev/dsp -r 8000 -t wav -s w - | ./noise-filter >bits I know i can record my mic input using rec -c 1 no.wav this is the command i tried using rec -c 1 -r 8000 -t wav -s noise.wav | ./noise-filter >bits but i get root@xxc:~/cc# rec -c 1 -r 8000 -t wav -s noise.wav - | ./noise-filter >bits rec WARN formats: can't set sample rate 8000; using 48000 rec FAIL sox: Input files must have the same sample-rate I have complied noise-filter noise-filter I think the tutorial is using an older version of SOX and REC I'm using sox: SoX v14.3.2 on Ubuntu 12.04 server Can someone please help me ?

  Read the article

• linux: refreshing groups without having to re-login

  - by orlandu63

  How does one refresh the groups that a logged-in user is in without having to re-login?

  Read the article

• 1080 HD video display - Windows 7

  - by blasteralfred

  I am running Windows 7 in my Dell Studio 1555 Laptop. I have ATI Mobility Radeon HD 4570 graphics card inside. When I try to watch a video, I can see only some disturbed texture. I can hear the audio and no prob with that. The I can see the video frames peeking sometimes but is pretty slower. I have DirectX (directx_feb2010_redist) and Win7 codecs installed. Here are some screenshots; The video details are; Name: video.mp4 Frame width: 1920 Frame height: 1080 Frame rate: 29 fps data Rate: 7958 kbps Total bitrate: 8052 kbps Just comment if you want more info.

  Read the article

• how to limit upload bandwidth per user in linux?

  - by Gihan Lasita

  Can anyone provide the tc command to limit upload bandwidth per user in Debian Lenny? I found that to mark packets per user with iptables I can use the following command iptables -t mangle -A OUTPUT -p tcp -m owner --uid-owner testuser -j MARK --set-mark 500 but I have no idea how to use tc update by running following commands, i managed to limit testuser upload bandwidth to 10Mbit iptables -t mangle -N HTB_OUT iptables -t mangle -I POSTROUTING -j HTB_OUT iptables -t mangle -A HTB_OUT -j MARK --set-mark 30 iptables -t mangle -A HTB_OUT -m owner --uid-owner testuser -j MARK --set-mark 10 tc qdisc replace dev eth0 root handle 1: htb default 30 tc class replace dev eth0 parent 1: classid 1:1 htb rate 10Mbit burst 5k tc class replace dev eth0 parent 1:1 classid 1:10 htb rate 10Mbit ceil 10Mbit tc qdisc replace dev eth0 parent 1:10 handle 10: sfq perturb 10 tc filter add dev eth0 parent 1:0 prio 0 protocol ip handle 10 fw flowid 1:10 now the problem is, i do not want to limit testuser's FTP bandwidth but by running above commands FTP speed also limited to 10Mbit. Regards

  Read the article

• Window 7 problem, Explorer.exe, DWM.exe

  - by Nitinzz

  I'm using Window 7 Ultimate. I get a problem with two processes, namely explorer.exe and sometimes dwm.exe. The two processes tend to use cpu between 20-30%. And it only occurs when i play some game on my PC. My PC works perfect until I play some game. And another important observation: They consume no cpu as such but only consumes when I try to refresh my desktop. I mean when I right-click on desktop. It takes seconds for refresh. I have no virus problems. I had already tried following things: Kill explorer.exe and relaunch from task manager. (Problem still persists) Kill dwm.exe, well it relaunches again. (Problem still persists) Log Off and Log On. (Problem still persists) Restart. Problem Solved. (But need an alternative). Can anyone kindly suggest some quick fixes to the problem?

  Read the article

• different ways decrease cpu usage

  - by lego69

  I use nothing but my cpu usage has got 100%, how can I decrease this rate?

  Read the article

< Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >