Search Results

Search found 16429 results on 658 pages for 'account names'.

Page 521/658 | < Previous Page | 517 518 519 520 521 522 523 524 525 526 527 528  | Next Page >

• Virtual Machine Network Services causes networking problems in Vista Enterprise 64 bit install

  - by Bill

  I have a Quad-core/8GB Vista Enterprise 64-bit (SP2) installation on which I installed Virtual PC 2007. I have a problem that is opposite of all that I found searching around the Internet--everybody has problems making network connections from their guest VM. When Virtual Machine Network Services is enabled in the protocol stack for my network card across a reboot, it causes access problems to the network. The amount of time to login in using a domain credentialed account is upwards of 3 minutes, then after reaching the desktop the network and sharing center shows that my connection to the domain is unauthenticated. Disabling and re-enabling the Virtual Machine Network Services (uncheck in network properties/apply/recheck/apply) fixes the problem. And as long as I have the VMNS disabled when I shutdown the restart runs smoothly. I just have to remember to enable after login and disable before shutdown. I have un-installed and re-installed Virtual PC 2007 multiple times with restarts between. The install consists of the SP1 + a KB patch for guest resolution fix. Any help would be greatly appreciated. Some additional information... At one point during my hairpulling and teethgnashing with this, I tried to ping my primary DC and observed some weird responses: (Our DC is 10.10.10.25, my dynamic IP was 10.10.10.203) Reply from 10.10.10.203, Destination host unreachable. Request timed out. Reply from 10.10.10.25: ... This is not consistently repeatable, but thought it might strike a chord with someone.

  Read the article

• Mailman delivery troubles

  - by stanigator

  I have apparently posted at the wrong place (superuser.com) for this question, so I'll just repost it here. Hope those of you who read both sites are not going to be offended. It's about mailing list management software called Mailman from GNU. Here are the details: Hosting provider: Vlexofree Domain: www.sysil.com with Google Apps Mailing List created from hosting cpanel: [email protected] I have registered a list of subscribers, and tried sending an email to [email protected]. I got the following error message: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550-5.1.1 The email account that you tried to reach does not exist. Please try 550-5.1.1 double-checking the recipient's email address for typos or 550-5.1.1 unnecessary spaces. Learn more at 550 5.1.1 http://mail.google.com/support/bin/answer.py?answer=6596 23si6479194ewy.44 (state 14). ----- Original message ----- MIME-Version: 1.0 Received: by 10.216.90.136 with SMTP id e8mr1469147wef.110.1264220118960; Fri, 22 Jan 2010 20:15:18 -0800 (PST) Date: Fri, 22 Jan 2010 20:15:18 -0800 Message-ID: <[email protected]> Subject: From: Stanley Lee <[email protected]> To: [email protected] Content-Type: multipart/alternative; boundary=0016e6dab0931bccc3047dcd2f1e - Show quoted text - Is there any way of fixing this problem? I would like to be able to have this mailing list to work through my hosting and domain. Thanks in advance.

  Read the article

• Anonymous file sharing without login window, from Windows 7 server to XP clients

  - by Niten

  I'm trying to provide machines on a small LAN with read-only, anonymous access to files shared from a Windows 7 workstation (let's call it WIN7SVR). In particular, I don't want clients to have to deal with a login window when they navigate to, e.g., \\WIN7SVR in Windows Explorer, but we do not have a domain and synchronizing accounts between the server and clients would be intractable. There are both Windows 7 and Windows XP clients that need access to these shares. I got this working for Windows 7 clients by just enabling the Guest account on WIN7SVR and setting appropriate share permissions. Other Windows 7 machines automatically try logging in as Guest, it seems, so their users don't have to deal with the login window. The problem is with the XP clients--they can access the server if the user enters "Guest" in the login window, but I don't want users to have to do that. So from what I gather, in my limited understanding of Windows file sharing, this boils down to granting null sessions access to file shares on WIN7SVR. But I've had no success so far on that front. I've tried all the following in the local group policy editor on the Windows 7 server: Set Network access: Let Everyone permissions apply to anonymous users to Enabled Set Network access: Restrict anonymous access to Named Pipes and Shares to Disabled Added the names of corresponding shares to Network access: Shares that can be accessed anonymously Added "ANONYMOUS LOGON" to Access this computer from the network under User Rights Assignment Any advice would be highly appreciated... I'm mostly a Unix guy, so I feel somewhat out of my league with Windows file sharing. I do understand that any sort of anonymous access to file shares isn't generally ideal from a security standpoint, but it's the most practical solution for us in this case, and access to our network is well enough controlled that share-level security isn't a concern.

  Read the article

• How best to manage my growing data in Excel?

  - by Mike

  This isn't a question about formulas or features in Excel. I'm debating the correct/best way to manage the growing amount of data 'I have to' manage in Excel (I produce PIVOT tables/reports for my management). DATA: I record the number of publications we order: cost, date ordered, start and end of subscription, who requested it, when they ordered it, when I ordered it, will it be cancelled next year, etc, etc, etc. DILEMMA: Obviously we re-order a lot of the same publications, so depending on how I manage the data I could be duplicating all over the place. OPTION 1: So, do I use ROWs = publication name in Row 1 and all the related columns for each financial year are copied and pasted after each financial year ready for the new FY information? This will lead to me going to column ZZ. OPTION 2: Or, do I use COLUMNs = each row has only one FY information for each publication and if we re-order or cancel a publication I re-type the publication name in a row below and fill in appropriate columns? This will lead to a long list of publications down to row 10000, and potential for misspelling of repeat ordered publication names. IDEAS: What's the best way - thinking in terms of pivot table best practice, being able to sum or count easy, report formatting, etc. Any best practices much appreciated.

  Read the article

• wild card redirects issue giving error this webpage has a redirect loop

  - by david

  In my website I changed or better word modified the directory name ""vehicles-cars"" to ""vehicles-cars-for-sale"" when i tried to redirect using wild card redirect my old directory name to new directory name in my web hosting cpanel account. every time when i open pages from that directory i am getting error code. This web-page has a redirect loop. The website is php. The problem is that that my lots of pages from old directory are indexed in googles and they are getting duplicate contents. If I redirect single page it works perfect but there are lots of pages so I need wild card redirect to redirect whole directory . I really need some advice what to do with this problem. Here is .htaccess file code for redirect thanks RewriteEngine on RewriteCond %{HTTP_HOST} ^example\.com$ [OR] RewriteCond %{HTTP_HOST} ^www\.example\.com$ RewriteRule ^vehicles\-cars\/?(.*)$ "http\:\/\/example\.com\/vehicles\-cars\-for\-sale\/$1" [R=301,L] i have other wilcard redirect of whole directory with same code and its working perfect here is the code in .htaccss file which is same as above and working perfect for this directory RewriteCond %{HTTP_HOST} ^adsbuz\.com$ [OR] RewriteCond %{HTTP_HOST} ^www\.adsbuz\.com$ RewriteRule ^autos\/?(.*)$ "http\:\/\/adsbuz\.com\/vehicles\-cars\-for\-sale\/$1" [R=301,L] so i dont understand whats wrong with the above code please i really need some expert advice thanks again

  Read the article

• Office365 Exchange: Cannot open shared two calendars in Outlook

  - by Mark Williams

  The problem: Outlook won't open the calendars on another user's mailbox and and a room mailbox, even when users have permission. Note: This problem is affecting more than one account on more than one machine. So I have a room mailbox and a personal mailbox on Exchange, both with shared calendars. There is a security group called "Scheduling Users" that have editor rights on both of these calenders. The room mailbox was created using PowerShell, per the instructions posted online (http://help.outlook.com/140/ee441202.aspx). Sharing worked on both of these folders initially. Users can still access these folders using OWA. So on to the problem. When users try to open these calendars in Outlook they receive one of the following messages. The set of folders cannot be opened. Microsoft Exchange is not available. Either there are network problems or the Exchange server is down for maintenance. Cannot open this item. Cannot open the free/busy information. The attempt to log on to Microsoft Exchange has failed. What I have tried so far: Resetting the permissions on both of the mailboxes. I deleted the security group permissions on both mailboxes, applied the change, then waited a bit and gave the permissions back. Deleted the OST file of the shared calendar from the Outlook data directory That is all I have been able to find online. Any thoughts? I have been going back and forth with the Office365 support folks for a while and they seem stumped too.

  Read the article

• Why does Facebook Chat through XMPP protocol on Pidgin Portable not authorize?

  - by Sara Neff

  I heard you can use facebook chat on desktops now. Thats awsome! What i didn't hear is that it is a pain in the butt! Not awsome! I've followed six nearly identical sets of instructions from six different websides, including the one that facebook generates for you, to get facebook chat connected through Pidgin. Its the latest portable version, so from what i hear the plugin is out of the question. Whenever I go to try and connect i get a message saying "Not Authorized" and buttons to either modify the account info, or retry. NOTHING i have done has fixed this, and I can't find anything remotely usefull anywhere. I am running windows xp, and running pidgin (portable) off of a flash drive. Someone please tell me what i have to do. I read about authorizing the chat on my actual facebook page. I'd have tried that if i could find out how to do it, but if its there they hid it good. HELP?!

  Read the article

• ACDSee alternatives for batch editing images

  - by Oxwivi

  I am looking for free, preferably open, alternatives to ACDSee for batch editing work. While I can do much of the work well on ACDSee, it's not entirely satisfactory despite having to pay for it. I need at least the following batch editing functions: Resize using either height or width and maintain aspect ration Auto contrast text overlays and occasionally, cropping oh, I make extensive use of renaming features as well Couple of issues with ACDSee are: I always need to highlight the Exposure section or auto contrast will not be done despite it being saved in the preset; and I can't define, move around the cropping box, forcing me to manually crop tons of images. I'm not an advanced, or "power photo-editor". I only require the basic stuff I described to be automated. My personal feature wish list (I'm pretty sure something so niche doesn't exist) would be text overlay based on the image names (images are named as image-1_1, image-1_2 or image-2_c1_1, image-2_c1_2, and text overlay would Image-1 and Image-2 C1 and Image-2 C2). I tried digiKam, but damn that thing is huge. It runs very slowly on my Pentium 4 and 1.5 GB RAM. On top of being a program with over 1 GB of files, the KDE library it uses is always slow regardless of it running on either Windows or Linux.

  Read the article

• Understanding !d command in sed with respect to saves

  - by richardh

  I have a directory of tab-delimited text files and some have comments in the first few lines that I would like to delete. I know that the first good line starts with "Mark" so I can use /^Mark/,$!d to delete these comments. After this deletion I have several other replacements that I make in the (new) first line that has variable names. My question is, why do I have to save sed's output to get my script to work? I understand that if I line is deleted, then the output doesn't proceed downstream because there is no output. But if I don't delete (i.e., !d) then why do I have to save to file? Thanks! Here is my shell script. (I'm a sed newbie, so any other feedback is also appreciated.) #!/bin/bash for file in *.txt; do mv $file $file.old1 sed -e '/^Mark/,$!d' $file.old1 > $file.old2 sed -e '1s/\([Ss]\)hareholder/\1hrhldr/g'\ -e '1s/\([Ii]\)mmediate/\1mmdt/g'\ -e '1s/\([Nn]\)umber/\1o/g'\ -e '1s/\([Cc]\)ompany/\1o/g'\ -e '1s/\([Ii]\)nformation/\1nfo/g'\ -e '1s/\([Pp]\)ercentage/\1ct/g'\ -e '1s/\([Dd]\)omestic/\1om/g'\ -e '1s/\([Gg]\)lobal/\1lbl/g'\ -e '1s/\([Cc]\)ountry/\1ntry/g'\ -e '1s/\([Ss]\)ource/\1rc/g'\ -e '1s/\([Oo]\)wnership/\1wnrshp/g'\ -e '1s/\([Uu]\)ltimate/\1ltmt/g'\ -e '1s/\([Ii]\)ncorporation/\1ncorp/g'\ -e '1s/\([Tt]\)otal/\1ot/g'\ -e '1s/\([Dd]\)irect/\1ir/g'\ $file.old2 > $file rm -f $file.old* done

  Read the article

• auto-mounting shared folders in VirtualBox

  - by brannerchinese

  I am writing to ask what the effect of the auto-mounting process is in VirtualBox, and where the folders can be accessed within a guest Linux system if auto-mount is used. I have VirtualBox 4.0.4 installed on Mac OS 10.6.7, with Guest Additions apparently running correctly. The guest OS is Ubuntu 10.04, and I observe no apparent problems with it. I find that if the shared folders have "auto-mount" unchecked in the VirtualBox settings, they can then be mounted using the prescribed syntax sudo mount -t vboxsf folder_name path_to_mount_point and all works as it is supposed to. But if the auto-mount option is checked, then I find that I can no longer mount the shared folders manually. I get the error mounting failed with the error: Invalid argument and the folders also do not appear to mount anywhere else accessible to me. Using the syntax sudo mount -t vboxsf without specifying a path installs them in /media, with their names prefixed with sf_, but they are not easily accessible there and I have not been able to change their owner using chown, either. Thanks for your patient explanation.

  Read the article

• Why can't I see all of the client certificates available when I visit my web site locally on Windows 7 IIS 7?

  - by Jay

  My team has recently moved to Windows 7 for our developer machines. We are attempting to configure IIS for application testing. Our application requires SSL and client certificates in order to authenticate. What I've done: I have configured IIS to require SSL and require (and tried accept) certificates under SSL Settings. I have created the https binding and set it to the proper server certificate. I've installed all the root and intermediate chain certificates for the soft certificates properly in current user and local machine stores. The problem When I browse to the web site, the SSL connection is established and I am prompted to choose a certificate. The issue is that the certificate is one that is created by my company that would be invalid for use in the application. I am not given the soft certificates that I have installed using MMC and IE. We are able to utilize the soft certs from our development machines to our Windows 2008 servers that host the application. What I did: I have attempted to copy the Root CA to every folder location for the Current User and Location Machine account stores that the company certificate's root is in. My questions: Could I be mishandling the certs anywhere else? Could there be a local/group policy that could be blocking the other certs from use? What (if anything) should have to be done differently on Windows 7 from 2008 in regards to IIS? Thanks for your help.

  Read the article

• ActiveDirectory user files aren't being shared? [on hold]

  - by Ryan

  I'm taking a class in college and my current project is to setup Active Directory. So I have two VMs, one is Windows Server 2008 R2 and the other is Windows 7. I setup the domain team15.net (this is the FQDN for the forest) on the W2008 server machine. And then I connected the Windows 7 machine to the team15.net domain, and now I can login to the administrator account on the W2008 machine by using TEAM15\Administrator for the username. However, any files that I add in Windows 7 while logged into TEAM15\Administrator are NOT shown in the Windows 2008 machine. Is this normal? It seems like any files I add to this user in the domain only exists for the machine that I'm currently using. Is it possible to change this so all files for all users are synced to all computers in the domain? If not then what are alternatives? I noticed that back in high school we also used domains but there was a shared drive E:\ that you had to store your files because if you put them on in the desktop instead then they would suddenly disappear once you logged out and back in. How can I setup a shared drive? and which computer would provide the storage for this drive?

  Read the article

• Authentication required by wireless network

  - by Roman

  I would like to use a wireless network from Ubuntu. In the network drop-down menu I select a network (this is a University network I have an account there). Then I get a windows with the following fields: Wireless Security: [WPA&WPA2 Enterprise] Authentication: [Tunneled TLS] Anonymous Identity: [] CA Certificate: [(None)] Inner Authentication: [some letters] User Name: [] Password: [] I put there my user name and password and do not change default value and leave "Anonymous Identity"blank. As a result of that I get "Authentication required by wireless network". How can I solve this problem? I think it is important to notice that our system administrator tried to find some files (which are probably needed to be used as "CA Certificate"). He said that he does not know where this file is located on Ubuntu (he support only Windows). So, probably this is direction I need to go. I need to find this file. But may be I am wrong. May be something else needs to be done. Could you pleas help me with that?

  Read the article

• How to rename network printer on Windows 7?

  - by Adrian McCarthy

  This question is similar to How do you rename a printer device in Windows 7 64 bit, except the answers there do not work, and I'll provide more information. This is a home network, not a domain. I have set up a Brother HL-5170DN. It is a network printer connected directly to an Ethernet hub. I can connect to it with Windows 7, but on Windows 7 it defaults to the name "binary_p1 on Brn37415f", which isn't very useful. And I cannot seem to change the name. I have it working with several Windows XP and Vista machines, and I can change the name on those machines. On Windows 7 Printer properties: I can see the "binary_p1" name on the General tab. I can select the text, but I cannot change it. The field is not grayed out, but I cannot type anything into it. On the Ports tab, all of the controls are grayed out (disabled). The selected Port is called "\\Brn_37415f\binary_p1", and it's described as "Client Side Rendering Provider" and the printer field says "binary_p1". On the Security tab, I can see that my account has "Manage this printer" permissions. If I choose Printer Server Properties, I can select the port and click Configure Port, but I get a dialog that says, "An error occurred during port configuration. This option is not supported." I have found many forums with people asking the same question without getting an answer. Update: No more bounties to offer, but I'm still looking for a solution to this problem.

  Read the article

• web.config file changings guide

  - by Student

  Hi experts how are you all? i am student, and learning asp.net c# visual studio 2010 with using sql server 2005. I have developed a website which has database. I developed this website with self studies taking help from internet. the website is completed and working perfectly in my computer. I have hosting server and domain name registered already. the problem is when I upload my website it doesn't work there the following error displays: Server Error in '/' Application. Configuration Error Description: An error occurred during the processing of a configuration file required to service this request. Please review the specific error details below and modify your configuration file appropriately. Parser Error Message: Unrecognized attribute 'targetFramework'. Note that attribute names are case-sensitive. Source Error: Line 11: <system.web> Line 12: <customErrors mode="Off" /> Line 13: <compilation debug="false" targetFramework="4.0"/> Line 14: </system.web> Line 15: </configuration> Source File: C:\Inetpub\vhosts\urdureport.com\httpdocs\web.config Line: 13 Version Information: Microsoft .NET Framework Version:2.0.50727.5472; ASP.NET Version:2.0.50727.5474 I don't know what should I do to get it work on hosting server please help me in this regard that what should I do with this. Thank you in advance

  Read the article

• using gmail as email relay for sendmail

  - by Nikita

  I used to be able to send emails using a gmail account & sendmail configured using one of the guides on the Internet, for example: http://appgirl.net/blog/configuring-sendmail-to-relay-through-gmail-smtp/ This is a small server and I've recently moved it to a different house. And sendmail has stop working. The only thing different in the network setup is a new router. What is happening: In the log files, I see the following error: ...stat=Deferred: smtp.gmail.com: No route to host When I run from the command line: strace sendmail -f A -t B -u "Subject" -m "Message" -tls=yes ssl=yes -s smtp.gmail.com:587 -xu A -xp XYZ It hangs on this call: recvfrom(3, "m0\201\203\0\1\0\0\0\0\0\0\4ares\3lan\0\0\34\0\1", 8192, 0, {sa_family=AF_INET, sin_port=htons(53), sin_addr=inet_addr("192.168.1.254")}, [16]) = 26 close(3) = 0 time(NULL) = 1339997943 open("/etc/localtime", O_RDONLY) = 3 fstat64(3, {st_mode=S_IFREG|0644, st_size=3477, ...}) = 0 fstat64(3, {st_mode=S_IFREG|0644, st_size=3477, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb76ff000 read(3, "TZif2\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\4\0\0\0\4\0\0\0\0"..., 4096) = 3477 _llseek(3, -24, [3453], SEEK_CUR) = 0 read(3, "\nEST5EDT,M3.2.0,M11.1.0\n", 4096) = 24 close(3) = 0 munmap(0xb76ff000, 4096) = 0 socket(PF_FILE, SOCK_DGRAM|SOCK_CLOEXEC, 0) = 3 connect(3, {sa_family=AF_FILE, path="/dev/log"}, 110) = 0 send(3, "<18>Jun 18 01:39:03 sendmail[268"..., 96, MSG_NOSIGNAL) = 96 nanosleep({60, 0}, So it looks like at some point it tries to resolve the DNS name, but I don't have anything running on 53, so it dies out and then just hangs. The other interesting thing is that msmtp works just fine on the same server. Update: ares in strace output is actually the name of my server, but .254 IP address is the address of the router. Could anyone tell me why this is happening or what further steps can I take to investigate the issue? Thanks!

  Read the article

• Rails app returns HTTP 422 for new ServerAlias - Internet Explorer only

  - by Snips

  I have a long-standing Rails app running on Mac OS X (apache2). The set-up uses Apache virtual hosts and Passenger. The Rails app also uses HTTP Basic Authentication. I need to migrate the app from one url domain to another - with some overlap of both domain names being accessible simultaneously for a period. To do this, I've added the new domain name as a ServerAlias of the existing domain name in the Passenger Virtual Host config. I can now Browse the Rails app using both the legacy url, and the new url from any of Safari, Chrome, Firefox, or Internet Explorer. I can also 'HTTP post' updates to the Rails app using Safari, Chrome, or Firefox. All good. Except, attempts to post updates from Internet Explorer result in the Rails app rejecting the update, The Rails app log contains the message, ActionController::InvalidAuthenticityToken (ActionController::InvalidAuthenticityToken): I have other domains & aliases working just fine on this same machine. Any suggestions as to what is causing the Rails app to reject posts from IE would be appreciated.

  Read the article

• Help, my CentOS servers keep going down , No route to host after a random uptime

  - by user249071

  Hello , I have a couple of Centos linux servers, that have a very simple task, they run nginx + fastcgi for php , and some NFS mounts between them, readonly They have some RPC commands to start some downloading processes with wget, nothing fancy , from a main server, but their behavior is very unstable, they simply go down, we tried to monitor ram , processor usage, even network connections, they don't load up so much, max network connections up to... 250 max, 15% processor usage and memory , well, doesn't even fill up, 2.5GB from 8GB max , I have no ideea why can a linux server go down like that, they aren't even public servers, no domain names installed no public serving, for sites. The only thing that I've discovered was that if i didn't restart the network service every couple of hours or so... the servers were becoming very slow, starting apps very slow, but not repoting a high usage of resources...Maybe Centos doesn't free the timeout connections, or something like that...It's based on Red Hat right? I'm not a linux expert , but I'm sure that there are a few guys out there that can easily have an answer to this , or even have some leads to what i can do ... I haven't installed snort, or other things to view if we have some DOS attacks, still the scheduled script that restarts the network each hour should put the system back online, and it doesn't.... Thank you in advance

  Read the article

• grep --color=auto with -i option disables the matching text color, why?

  - by emptyset

  I was messing around with grep and put this in my .zshenv: export GREP_OPTIONS="--color=auto" export GREP_COLORS='mt=1;34' I was bonking my head on the keyboard and changing GREP_COLORS around for a minute trying to figure out why the folder colors were working, but the matching text wasn't. I was doing this: $ grep -R -n -i -e "functionFoo\(" --include=*.cs --exclude-dir=Logs * The line number and file names were set with the default colors, but the matching text wasn't. After spending way too much time, I thought to do this: $ grep -R -n -e "functionFoo\(" --include=*.cs --exclude-dir=Logs * (I removed the -i option.) That's all it took to get the matching text to correctly show up in bold blue. This is a Cygwin on Vista setup, with rxvt running zsh. Any idea why grep colors would break on specifying a case-insensitive match? Update: Under cygwin 1.7, it's a little bit better - case insensitive search works correctly, but it only highlights the word that matches the expression exactly. In other words, "FunctionFoo" highlights "FunctionFoo" but not "functionFoo" and vice versa. Probably a grep issue so I'll be submitting it to that list.

  Read the article

• LVM2 volume group lost

  - by MrG

  I updated one of my servers, but - although I took care not to modify - the volume groups on /dev/sdb1 were lost, although the physical volumes seem to be still there: [root@server ~]# pvscan PV /dev/sda2 VG VolGroup lvm2 [465,16 GiB / 0 free] PV /dev/sdb1 lvm2 [1,82 TiB] Total: 2 [2,27 TiB] / in use: 1 [465,16 GiB] / in no VG: 1 [1,82 TiB] [root@server ~]# pvs -v Scanning for physical volume names PV VG Fmt Attr PSize PFree DevSize PV UUID /dev/sda2 VolGroup lvm2 a-- 465,16g 0 465,16g HftbaD-MBs0-3p7D-6O13-CrzU-T9Gb-6W0ofB /dev/sdb1 lvm2 a-- 1,82t 1,82t 1,82t dD4XZP-WStA-61xV-5Sff-ifmW-R4rR-JenHoU [root@server ~]# pvck -d -v /dev/sdb1 Scanning /dev/sdb1 Found label on /dev/sdb1, sector 1, type=LVM2 001 Found text metadata area: offset=4096, size=1044480 Found LVM2 metadata record at offset=10752, size=1037824, offset2=0 size2=0 Found LVM2 metadata record at offset=9216, size=1536, offset2=0 size2=0 Found LVM2 metadata record at offset=7168, size=2048, offset2=0 size2=0 Found LVM2 metadata record at offset=5632, size=1536, offset2=0 size2=0 I attempted to fix it as described here and was able to extract the 4 meta data sets listed above (using i.e. dd bs=1 skip=5632 count=1536 if=/dev/sdb1 of=output.file), none of them includes the lv_data which I'm missing. Please advise how I could access the files which should be on /dev/sdb1 there. Any help is appreciated!

  Read the article

• What could cause these "failed to authenticate" logs other than failed login attempts (OSX)?

  - by Tom

  I've found this in the Console logs: 10/03/10 3:53:58 PM SecurityAgent[156] User info context values set for tom 10/03/10 3:53:58 PM authorizationhost[154] Failed to authenticate user (tDirStatus: -14090). 10/03/10 3:54:00 PM SecurityAgent[156] User info context values set for tom 10/03/10 3:54:00 PM authorizationhost[154] Failed to authenticate user (tDirStatus: -14090). 10/03/10 3:54:03 PM SecurityAgent[156] User info context values set for tom 10/03/10 3:54:03 PM authorizationhost[154] Failed to authenticate user (tDirStatus: -14090). There are about 11 of these "failed to authenticate" messages logged in quick succession. It looks to me like someone is sitting there trying to guess the password. However, when I tried to replicate this I get the same log messages except that this extra message appears after five attempts: 13/03/10 1:18:48 PM DirectoryService[11] Failed Authentication return is being delayed due to over five recent auth failures for username: tom. I don't want to accuse someone of trying to break into an account without being sure that they were actually trying to break in. My question is this: is it almost definitely someone guessing a password, or could the 11 "failed to authenticate" messages be caused by something else? EDIT: The actual user wasn't logged in, or using a computer at the time of the log in attempts.

  Read the article

• Outlook locking network connection/session?

  - by HaydnWVN

  Scenario: We have an 'automatic orders' machine sat in the corner running XP with Outlook 2003. Its job is to check for new emails on a specific account, when it encounters one it checks the e-mail body for specific wording to determine which customer it is from (using a macro), then it checks the attachment for specific order codes before parsing the attachment to create a .csv file (which is then e-mailed onto one of the sales team) before importing the .csv into our bespoke ERP/Sales Order system to create an order. Problem: Periodically the machine will have symptoms of a lost network connection (unable to connect to any network source). Sometimes after several days, sometimes over a week. Volume of emails/orders processed does not seem to be linked. Additional info: The machines .pst is stored on a mapped network location. The .csv created is stored on a mapped network location. This is a workgroup, not a domain. All network drives are Samba shares from an Ubuntu fileserver. Our bespoke system runs from a database (MySQL) Ubuntu server. Our troubleshooting so far: I have switched machines (previous was Win2000) with the same symptoms. Restarting the machine FIXES the problem. Closing Outlook and then end tasking an Outlook.exe background process FIXES the problem. If you close Outlook, without end taking the background process, outlook will not reopen (saying it cannot find the pst file & it will not open any network location). Does Outlook have some kind of 'max session' linking it to network activity that is not closing after a mail request? Could Auto-archive be causing this? Is there a tool to check/display what each outlook.exe process is doing? Have not found many ways to troubleshoot this yet, as it is so infrequent...

  Read the article

• How could one archive all emails sent from employees?

  - by Schnapple

  My client runs a small business. This business has a small number of employees. They are currently hosted through GoDaddy for web and email. For legal reasons the client would like to archive emails sent by their employees. Currently the emails are all done through POP3 so all the email is basically housed in files on individual machines (remember, small business). It's been proposed an inexpensive solution to this would be to have all emails BCC'd to a main account so that conversations with the outside would could be archived and tracked. I have not investigated it myself personally but apparently GoDaddy can do something along these lines for all incoming email but not for outgoing email. Is there a way to set up email accounts for a particular domain to where a specified admin user could be copied on all outgoing email? UPDATE: I've modified the title to reflect employees not users. The goal of this is to archive sent emails for legal reasons. This is something the employees will be cognizant of and on board with. The bottom line here is to basically emulate a feature of a larger-class platform through a smaller, cheaper platform. If the answer is "can't do it, buy an Exchange license" that's fine. My apologies for phrasing this so poorly. I understand why there was so much confusion.

  Read the article

• How do I push my initial snapshot to a subscriber server in SQL Server 2000?

  - by Kev

  I'm configuring Transactional Replication using the Push model. The scenario is: The SQL Servers: SQL01 (publisher) and SQL02 (subscriber) - both running SQL 2000 SP4. Both servers are standalone (i.e. not domain members) Both servers have their FQDN and NETBIOS names in their HOSTS files I've managed to configure SQL01 to publish my database and configured a Push subscription for SQL02 using the Push New Subscription wizard and set the Distribution Agent to update the subscription continuously. On the Push Subscription wizard "Initialise Subscription" page I've selected "Yes, initialise the schema and data" and ticked the "Start the Snapshot Agent to begin the initialisation process immediately" option. All the required services are running (SQL Agent). When I complete the wizard and browse the Replication - Publications folder I can see my publication (blue book with arrow). The publication shows the Push subscription and its status is Pending. If I look in the c:\Program Files\Microsoft SQL Server\Mssql\Repldata folder I see a number of T-SQL scripts for each table e.g. Products.bcp, Products.sch, Products.idx. What should happen now? Should my replicated database now (magically) appear on the subscription server?

  Read the article

• Site Goes Offline Every Day At Midnight - No One Knows Why

  - by HollerTrain

  0 down vote favorite Seems today a website I manage has been going online and offline between 12a and 12:25a. I have no idea what is causing the issue so I am seeking guidance on where to start. It is a Wordpress based site. So here is what I DO know: I have a pingdom account which alerts me when the site goes offline so we can see every day, like clockwork, the site goes on/off. At the time of the ups/downs I see a lot of strain on the memory usage. Look at the load average when the site is going online/offline (http://screencast.com/t/BRlfXkqrbJII). Then I ran this command to restart http (http://screencast.com/t/usVtYWZ2Qi) and the memory usage then goes down to this (http://screencast.com/t/VdTIy3bgZiQB). An hour after I restarted http, the site then went offline/online so restarting the http didn't do much help. When the site is going offline/online, I ran the top command and get this (http://screencast.com/t/zEwr7YQj3). Here is a top command when the site is at it's lowest (http://screencast.com/t/eaMfha9lbT - so this would be dubbged "normal"). Here is a bandwidth report (http://screencast.com/t/AS0h2CH1Gypq). The traffic doesn't seem to be that much (http://screencast.com/t/s7hrWNNic1K), but looking at my times the site is going up/down this may be one of the reasons? I have the dvp Nitro package at Media Temple (http://mediatemple.net/webhosting/nitro/). So at this point I would request some help in trying to figure out what the cause of this is, and how I can go about pinpointing this issue. ANY HELP is greatly appreciated.

  Read the article

< Previous Page | 517 518 519 520 521 522 523 524 525 526 527 528  | Next Page >