Search Results

Search found 18954 results on 759 pages for 'connection reset'.

Page 526/759 | < Previous Page | 522 523 524 525 526 527 528 529 530 531 532 533  | Next Page >

  • Network configuration problem

    - by Musti
    in my dorm I have to change network configuration and then if it is successfull, I have to enter a user name and password for wired internet connection. Anyway, I had many attempts but I couldnt achieve, and please look at my steps and tell me if there is something wrong and at the end there is an error, but I really dont have any idea about this error. (I am a new ubuntu user, and network is far away of my interests) 1) /etc/network/interfaces auto eth0 iface eth0 inet static address 172.030.014.038 netmask 255.255.255.252 network 192.168.2.0 broadcast 192.168.2.255 gateway 172.030.014.038 2) sudo gedit /etc/resolv.conf nameserver 010.050.001.001 nameserver 010.050.001.002 3) /etc/init.d/networking stop Deconfiguring network interfaces... [ OK ] 4) /etc/init.d/networking restart Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces Reconfiguring network interfaces... 172.030.014.038: Unknown host ifconfig: `--help' gives usage information. Failed to bring up eth0 Note: IP-address, netmask, gateway, Preferred DNS server and Alternate DNS server ara given by the management of Dorm. It wad very easy in windows but I couldnt achieve in Ubuntu. I also tried to edit from "edit connections" but the save button is gray and I cannot save it. Thanks in advance. / Musti

    Read the article

  • How to clear unshown OSD notifications

    - by Avatar Parto
    I am a webmaster of 2 active websites. Every time I start Thunderbird, it downloads all the new messages from the admin mail addresses of these sites - [email protected], [email protected], [email protected], etc. There are about 20 of them - this includes my personal email accounts. Now, am not always connected to the internet and there arises cases where I need to access already downloaded mails. Thunderbird then tries to connect to the internet, which it can't coz am offline, and then displays about twenty OSD notifications, one after the other, telling me that connection for each email address has failed. That's frustrating and it really eating me up. Am looking for a way, either: 1. To tell Thunderbird NOT to connect to the internet when am offline, or 2. To clear all these notifications after like the first one shows. And if it will help, am using ubuntu 13.04 and Thunderbird 24.0 and I always keep my computer fully updated. Any help is welcome. Thanxs.

    Read the article

  • How do I record sound from my CD/DVD player without other system sounds in the mix?

    - by Software Monkey
    Using GoldWave I can record via the "Stereo Mix" channel, but I get no sound on the "CD" channel. Of course, using the stereo mix also mixes in all system sounds, including beeps, etc. I have the analog out on the DVD player connected to the CD-IN connector on the MoBo. I can hear CDs and DVDs playing just fine through my speakers - is this because the CD is also IDE data connection in to deliver the sound to the sound card, then? I specifically want to record a DVD; I can easily rip a CD using GoldWave's built-in ripper. Is there anything I have forgotten or have to enable? Or is it likely I have a damaged cable? My system is an MSI mobo and is running Windows XP SP3.

    Read the article

  • CGI error from PHP when running exec() on IIS

    - by Patrick
    Windows Server 2003 x64 PHP 5.2 IIS 6.0 The program Ink2Png.exe is set with Everyone-Read and Execute permissions. As does its dependency (microsoft.ink.dll) PHP Safe Mode is off exec() is passed [the full exe path], space, [full path to another file] This other file also has full read permissions. The output directory has full write permissions. As soon as exec() is hit, the connection dies, the browser does not even receive a full set of http headers, and it reports a CGI error. Examining the output, it appears the program was not even run. Any ideas? How can I figure out what exactly is happening and get it running again? EDIT: Also, it is a .NET application, if that is significant in any way.

    Read the article

  • How to search unique dynamic data in a sheet and then copy relevent row in diffrent sheet?

    - by Hemant
    I am getting data from internet (DataFrom Web) In sheet1. Then I disperse that data in to three sheets based on three unique text. Like a,b and c. Rows are copied to sheet a,b and c sheets depending on text (a,b,c) they have. All the rows have one unique text (like url) by which they can be searched. I have added static data corresponding to the row. The problem is when ever internet data is changed (row addition/substitution or randomized). My static data loses its connection with the original row for which it was written. I want to search the data based on one unique key and put it to its original place where it used to be with static data.

    Read the article

  • 550 operation not permitted using FTP

    - by monkey_boys
    I'm using FTP to manage some files on a site I run but keep seeing this (truncated) error log: Command: DELE calendarpermission.php Response: 550 calendarpermission.php: Operation not permitted [...] Command: DELE button_down.gif Response: 550 button_down.gif: Operation not permitted Command: CWD /domains/example.com/public_html/admincp Response: 250 CWD command successful Command: PWD Response: 257 "/domains/example.com/public_html/admincp" is the current directory Command: RMD control_examples Response: 550 control_examples: Operation not permitted Command: CWD /domains/example.com/public_html Response: 250 CWD command successful Command: PWD Response: 257 "/domains/example.com/public_html" is the current directory Command: RMD admincp Response: 550 admincp: Operation not permitted Status: Retrieving directory listing... Command: PASV Response: 227 Entering Passive Mode (122,155,5,50,138,244). Command: MLSD Response: 150 Opening ASCII mode data connection for MLSD Response: 226 Transfer complete Status: Directory listing successful Status: Set permissions of '/domains/example.com/public_html/admincp' to '777' Command: SITE CHMOD 777 admincp Response: 550 CHMOD 777 admincp: Operation not permitted What do I do to solve this?

    Read the article

  • Logging upload attempt with proftpd

    - by Amit Sonnenschein
    I have a logging server that i use with external hardware, the idea is that a special hardware is uploading logs about it's operation every few hours and from the server i can do whatever i need to do with the information, the old server was getting a bit too old and i've moved to a new one, i've install lamp,proftpd and ssh (just the same as i had on the old server). now for some reason the logs are not being uploaded and i don't know why. the hardware uses a direct ftp access - i've the proftpd.log and saw that the connection is not being rejected (just to make sure i didn't make a mistake with the user/pass) my problem is that for some reason the upload itself is failing... it might be due to wrong path (as it's hard coded in the hardware) but i can't really know as proftpd wont give me any details.. i've tried to change the loglevel to "debug" thinking it would give me more information but i don't see any change... is there any other way i can make sure proftpd logs EVERTHING ?

    Read the article

  • Internet problems

    - by dan
    I've got problems on my freshly installed windows Xp machine. I cannot connect to the internet and I've tried various 'solutions' provided to me by the help and support center. Surprisingly none of them worked... Anyways, I've got 3 pc's next to me sharing a lan which is connected to the internet though a modem. The computer I use right now uses windows xp aswell and runs without any problems. I've tried everything on not working computer. I've ran the connection wizard several times, but it's not working :( Also I've very little experience with this version of windows, so I'm sorry if the solution is obvious.

    Read the article

  • Network on linux server is periodically down

    - by Fabian
    I have an old server running Fedora 4 that occasionally just stops responding via network for about an hour. This happens 1-2 times a week. Also no connection from the server itself to any other computer on the network is possible when it happens. The network settings and routes look fine. There are no unusual log messages and no unusual processes running at that time. If I restart the network or just do an ifconfig eth0 down & ifconfig eth0 up it works fine afterwards. I know that the server should be updated to a currently supported OS, but that is not really an easy option right now. Any ideas on how I could diagnose and fix that problem?

    Read the article

  • How to block spam site republishing my content

    - by Fo.
    I noticed today that Google search results shows some spam copies of one of my sites. The url looks something like this: http://[subdomain].spamsite.com/www.example.com ...where example.com is my site. In my Apache access logs I'm noticing several lines like the following whenever I load the above url: 127.0.0.1 - - [219/Oct/2012:19:27:34 +0000] "OPTIONS * HTTP/1.0" 200 - "-" "Apache (internal dummy connection)" The spammer's site shows an exact up to date copy of my site, so I think they are pulling in live data. Any idea how I can block this traffic?

    Read the article

  • central log-server with auditdisp

    - by johan
    I want to setup a central log-server. The log-server is running with debian 6.0.6 and the audit daemon is installed in version 1.7.13-1. The Clients are running with Red Hat 5.5 and they connect to the log-server via audispd. The connection works fine and i get all messages from each node. My questions is: is it possible that the auditd daemon from the log server write the messages from each node in a separate file? I try to transfer the messages via the syslog daemon, that works but i can not use tools like ausearch to analyze these log-files.

    Read the article

  • How do I set my router up to authenticate with my service provider?

    - by João Lourenço
    Currently I have this setup: D-Link DSL2640U connected to the phone line: VPI/VCI 0/40, Service Category UBR Without PCR Service pppoe_0_40_3 Interface nas_0_40 Protocol Bridging (LLC/SNAP-Bridging) 802.11q not enabled Bridge Service Enabled Computers have individual PPPoE connections (in Network and Sharing Centre - Set up a new connection or network - Connect to the Internet - Broadband (PPPoE) - Username and Password) How would I move these settings on each individual PC to the router so that all I need to do is connect to the wireless? I have been unsuccessful setting up anything other than Windows PCs on the network (I have tried Macs, iOS and Nokia SmartPhones too). Thanks for the responses in advance!

    Read the article

  • Why such a dramatic difference in wireless router max. simultaneous connections?

    - by Jez
    Recently, I've needed to look into buying a wireless router for a mission-critical system at work that will need to support quite a few simultaneous connections (potentially a few hundred laptops). One thing I've noticed is that there seems to be a dramatic difference between the max. simultaneous connections different routers can support; see this page for example - anything from 32 to 35,000! Why is there this degree of difference? You'd have thought that if we know how to make routers that can handle thousands of connections, we wouldn't be making stuff that's limited to a pathetic 32 anymore. Is it a firmware thing? A hardware thing? Are low-end manufacturers purposely putting low arbitrary connection limits in so people can be "encouraged" to pay more for high-end routers?

    Read the article

  • some websites not opening completely

    - by mkk
    Hi everybody, I am using bsnl broadband connection, modem: wa3002g1 os: xp(86x) / vista(64x) A few days back I have changed the modem (don't know the previous modem no) because of some issues. since then I am not able to open most of the websites in firefox, IE6/8, chrome, opera. If i connect with other network like reliance data card, those websites are opening, if i connect bsnl the problem will be same again. I called to customer care many times, but no use. Please help me to find the solution. Thank you in advance.

    Read the article

  • Root certificate authority works windows/linux but not mac osx - (malformed)

    - by AKwhat
    I have created a self-signed root certificate authority which if I install onto windows, linux, or even using the certificate store in firefox (windows/linux/macosx) will work perfectly with my terminating proxy. I have installed it into the system keychain and I have set the certificate to always trust. Within the chrome browser details it says "The certificate that Chrome received during this connection attempt is not formatted correctly, so Chrome cannot use it to protect your information. Error type: Malformed certificate" I used this code to create the certificate: openssl genrsa -des3 -passout pass:***** -out private/server.key 4096 openssl req -batch -passin pass:***** -new -x509 -nodes -sha1 -days 3600 -key private/server.key -out server.crt -config ../openssl.cnf If the issue is NOT that it is malformed (because it works everywhere else) then what else could it be? Am I installing it incorrectly? Update I tried changing the certificate attributes, but to no avail: openssl genrsa -des -passout pass:***** -out private/server.key 2048 openssl req -batch -passin pass:***** -new -x509 -nodes -sha256 -days 3600 -key private/server.key -out server.crt -config ../openssl.cnf

    Read the article

  • LPR command won't recognize CUPS printer

    - by Datapimp23
    I have a cups server with one shared printer configured on it. It prints test pages without problems. printername (Idle, Accepting Jobs, Shared) Description: desc Location: Driver: Zebra ZPL Label Printer (grayscale, 2-sided printing) Connection: socket://172.20.50.26 Defaults: job-sheets=none, none media=oe_w288h432_4x6in sides=one-sided This is the output from lpstat -t. it shows that the printer is idle and accepting requests admin@SERVER:~$ lpstat -t scheduler is running no system default destination device for printername: socket://172.20.50.26 printername accepting requests since Thu 26 Jan 2012 01:29:35 PM CET printer printername is idle. enabled since Thu 26 Jan 2012 01:29:35 PM CET Now when I want to send a printjob to it via an LPR command it won't recognize the printer /usr/bin/lpr -P printername test.pdf Result lpr: ttn_seg_zebra1: unknown printer What am I missing here ?

    Read the article

  • Ubuntu based VPN server behind NAT router?

    - by maartenn88
    I have a small intranet- and file-server inside our company, which can only be reached from inside our own network. I'd like to be able to reach the intranet and files on the server from outside the network, however I don't really like the idea of completely opening security by forwarding the ports on our NAT-router, so I'd prefer to enable a VPN possibility for this. So I have a router, which is the DHCP server and has NAT function, and I have an Ubuntu Server with the files and intranet on it. How do I configure these two so that I can make a VPN connection with my network in order to reach the server? thanks in advance for any answer!

    Read the article

  • Twitter Tuesday - Top 10 @ArchBeat Tweets - August 12-18, 2014

    - by Bob Rhubart-Oracle
    Man in gray hat: "You know, more than three thousand people follow @OTNArchBeat on Twitter. I wonder which tweets were the most popular over the last seven days." Man in brown hat: "Shut up! I think I see a UFO!" Man in gray hat: "That's OK. I'll just read this blog post." RT @java: "Programmers are creative people and typically delight in contriving clever ways to solve problems." -Casimir Saternos in @OracleJavaMag Aug 18, 2014 at 12:54 PM The Offer Still Stands: Produce your own episode of the OTN ArchBeat Podcast. Click for details. Aug 13, 2014 at 02:03 PM Binge-Ready! Watch the Top 10 OTN ArchBeat Videos featuring @stewartbryson @stenvesterli @gurcanorhan Aug 13, 2014 at 11:49 AM Oracle Announces First Java 9 Features | InfoQ Aug 18, 2014 at 12:20 PM Getting Started wit the #Coherence Memcached Adaptor | David Felcey Aug 18, 2014 at 10:19 AM #WebLogic Data Source Connection Labeling | Steve Felts Aug 14, 2014 at 10:03 AM How to introduce #DevOps into a moribund corporate culture | ZDNet Aug 15, 2014 at 11:23 AM Sample Chapter: Installing Oracle #WebLogic Server 12c and Using the Management Tools | Sam Alapati Aug 14, 2014 at 11:09 AM Building a Responsive #WebCenter Portal Application | @JayJayZheng Aug 12, 2014 at 11:04 AM #OEM12c Cloud Control authorization with Active Directory | Jeroen Gouma Aug 14, 2014 at 10:16 AM

    Read the article

  • SQUID Transparent SSL proxy (no intercept)

    - by user974896
    I know how to have squid work as a transparent proxy. You put it into transparent mode then use your router or IPTABLES to forward port 80 to the squid port. I would like to do the same for SSL. Every guide I see mentions setting up keys on the squid server. I do not want squid to actually decrypt the SSL traffic then establish a connection with the server, rather I would like squid to simply forward the SSL traffic as is. The only thing I would like to do is be able to check the SSL request for any offending IPs and drop the packets if the destination is one of them.

    Read the article

  • estimating size of reply HTTP headers

    - by Guanidene
    I am trying to download a file via a basic socket connection, using a HTTP GET request. So, I have to specify how many bytes of data coming in I have to read from the socket. However, I am having trouble deciding the amount of data (say, in bytes) the server would reply back with. I know that there is a "Content-Length" field in the reply sent by server, but that gives me the size of the actual data (without the http headers). Is there a way to get the exact size of HTTP headers sent by the server or an estimation is required? (I am doing this for downloading on a mobile network, where every bit of data matters in terms of time and money, so I don't wish to make an unnecessary larger estimate of the header size.)

    Read the article

  • "remote file operation failed" on Hudson

    - by Aveen
    I am running a Windows slave for Husdon 1.337 (Linux master). When running a project on the Windows node, it fails with the following message: Building remotely on winTestSlave Checking out a fresh workspace because there's no workspace at C:\hudson\***\ejb remote file operation failed It did work yesterday and I have not upgraded Hudson or changed its configurations (or the slave's configurations) in any way. I establish the connection between the slave and the master by running the following command on a cygwim prompt on the slave: java -jar slave.jar -jnlpUrl http://myserver/computer/winTestSlave/slave-agent.jnlp I saw the issue http://issues.hudson-ci.org/browse/HUDSON-5374 and did as instructed in the work-around but that did not work. I also tried with a newer version of slave.jar (version 1.356) but that did not work either. Does anyone please have any idea of how to fix this? I really cannot find more information anywhere else!

    Read the article

  • Software Center Freezing on Xubuntu 12.10

    - by AC3
    Whenever I open Software center I get this error: 012-12-12 16:19:29,196 - softwarecenter.fixme - WARNING - logs to the root logger: '('/usr/lib/python2.7/dist-packages/dbus/proxies.py', 410, '_introspect_error_handler')' 2012-12-12 16:19:29,196 - dbus.proxies - ERROR - Introspect error on :1.74:/com/ubuntu/Softwarecenter: dbus.exceptions.DBusException: org.freedesktop.DBus.Error.NoReply: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. 2012-12-12 16:19:54,713 - softwarecenter.ui.gtk3.app - INFO - setting up proxy 'None' 2012-12-12 16:19:54,816 - softwarecenter.db.database - INFO - open() database: path=None use_axi=True use_agent=True 2012-12-12 16:19:55,705 - softwarecenter.region - WARNING - failed to use geoclue: 'org.freedesktop.DBus.Error.ServiceUnknown: The name org.freedesktop.Geoclue.Master was not provided by any .service files' 2012-12-12 16:19:56,575 - softwarecenter.backend.reviews - WARNING - Could not get usefulness from server, no username in config file 2012-12-12 16:19:56,592 - softwarecenter.fixme - WARNING - logs to the root logger: '('/usr/lib/python2.7/dist-packages/gi/importer.py', 51, 'find_module')' 2012-12-12 16:19:56,592 - root - ERROR - Could not find any typelib for LaunchpadIntegration 2012-12-12 16:19:56,910 - softwarecenter.ui.gtk3.app - INFO - show_available_packages: search_text is '', app is None. 2012-12-12 16:19:56,935 - softwarecenter.db.pkginfo_impl.aptcache - INFO - aptcache.open() Not sure if it is a bug or not, have uninstalled and reinstalled the program already with synaptic. Very little experience with linux and any help will be appreciated

    Read the article

  • Load balancing + NAT issue on BNT GBE 2-7 gear

    - by Clément Game
    Hi guys, I've got troubles configuring an Hardware load-Balancer with NAT functions. I have the following architecture: Internet === VIP (public) LB (private ip) ==== private addressed servers When a connection is initialised from the outside (internet) , the LB correctly forwards the SYN packet to one of the private servers. But when these servers want to reply with a SYN/ACK there is a problem. the initial SYN packet had as ip header : VIP = Private_server_Address But the private servers cannot reach VIP from their side (this is normal since it's nated), and then provide a correct reply. Have you guys any solution to correctly forward the packets to their correct destination ? Note: The load balancer, which is the default gw for the servers, also has a NAT rule for "masquerading" (actually more SNAT than real masquerading) Regards, Clément.

    Read the article

  • Model a chain with different elements in Unity 3D

    - by Alex
    I have to model, in unity 3D, a chain that is composed of various elements. some flexible, some rigid. The idea is to realize a human-chain where each person is linked to the other by their hands. I've not tried to implement it yet as i've no idea on what could be a good way to do it. In the game i've to manage a lot of chains of people... maybe also 100 chains composed of 11-15 people. The chain will be pretty simple and there won't be much interaction... Probabily some animation of the people one at time for each chain and some physic reaction (for example pushing a people in a chain should slightle flex the chain) the very problem of this work is that in the chain each object is composed by flexible parts (arms) and rigid parts (the body) and that the connection should remain firm... just like when people handshake... hands are firm and are the wrists to move. i can use C4D to model the meshes. i know this number may cause performance problems, but it's also true i will use low-poly versions of human. (for the real it won't be human, but very simple toonish characters that have harms and legs). So actually i'm trying to find a way to manage this in a way it can work, the performance will be a later problem that i can solve. If there is not a fast 'best-practiced' solution and you have any link/guide/doc that could help me in finding a way to realize this is, it would be very appreciated anyway if you post it. thanks

    Read the article

  • Domain users sometimes cannot access our NAS

    - by Natalie
    I'm using a QNAP TS-410 Turbo NAS and I've got domain users connecting to it frequently everyday. However, there are times when their connection to the NAS will seem to just drop and, suddenly, they cannot access their network drives (which I had set up our Domain Controller to automatically map to folders on the NAS). Could you please tell me what may cause this? I don't think it is a network issue as everything else seems to work just fine. (If more details are needed, please let me know so I can update this question.)

    Read the article

< Previous Page | 522 523 524 525 526 527 528 529 530 531 532 533  | Next Page >