Search Results

Search found 16182 results on 648 pages for 'event tracing'.

Page 526/648 | < Previous Page | 522 523 524 525 526 527 528 529 530 531 532 533  | Next Page >

  • Will just a couple of thermal "trip" shutdowns typically damage a CPU?

    - by T.J. Crowder
    The short version If a CPU gets so hot that the system turns itself off because of a thermal trip signal just a couple of times, is it likely that the CPU will be damaged? Or does the trip do its job, turning it off before the CPU gets damaged? (This is with all default settings in the BIOS; I haven't raised any temp thresholds or overclocked anything.) The longer version I just got this Intel Atom D510-based fanless system, installed a 2.5" mobile SATA drive and two 2GB PC2-6400s, closed it up, and having checked everything was recognized in the BIOS, set about installing Ubuntu. After a couple of false starts related, I think, to the external DVD drive I was using, I got the install happily running along. About three-fourths or so of the way through the install, having been running less than an hour, the machine turned itself off. I was actually out of the room at the time, but when I came back and turned it back on, it said it had shut down due to a thermal event. I went into the BIOS and saw that (at that point, having just been turned back on after a couple of minutes off), it was running 87C. As near as I can tell from Intel's docs (PDF here), the max "junction" temperature for the CPU is 100C and it will raise a THERMTRIP signal at 125C. Yowsa. Presumably there will be some back-and-forth with the vendor on this, I'm just wondering whether letting it get that hot a couple of times is likely to end up damaging it.

    Read the article

  • No signal on monitor after plug it to a linux box

    - by yaroot
    I use my old computer as an NAS, so I remove the monitor after I installed linux on it (disconnect vga cable). I use ssh to control the machine and it works fine. Until some day, after kernel/softare upgrade or messing up some configs, I cannot connect to it through ssh, then I have to plug the monitor back, but the monitor says "No input signal". So I have to restart the computer WITH the monitor connected, and the monitor's back! I think the computer/linux kernel doesn't detect the monitor plug-in event. So how can I start my linux box without a monitor, but when it goes wrong I can still plug my monitor (vga) back and use the console. Edit: just one pci-e video card, has dvi, vga, tv/out (s-video) Edit2: Xorg is not running. I just need the console (CTRL+ALT+F1). The problem is, if the machine booted without a monitor connected, it won't give me a pseudo terminal after I attach the vga cable while it's running. Clearly the monitor is not auto detected as usb device. I'm wondering how to let the monitor auto detected.

    Read the article

  • MSE updating fails, no warning or error message.

    - by WebDevHobo
    I'm running Windows 7 Ultimate, 32-bit. For the last couple of days, MSE doesn't fails to update, remaining stuck at version 1.75.119 I presume that an error log is created somewhere, or an event log, but I don't know where to find those. It just says "connection failed". Tried it at home, at work and friends places, but never works. Restarted computer a lot of times now, checked for Microsoft Updates in general, but nothing shows up. EDIT: I've opened a bounty for this, because I really don't know what to do anymore. The oldest answer(the long post) here did not work. Besides this problem, I'm having trouble using MSI installers too. I've had to add the SYSTEM group to a lot of maps and give them full control, but shouldn't the SYSTEM already be there? Also, I had to remove the "read-only" attribute from the ProgramData and Users folders, add the SYSTEM group there too and give them full control. Only then will the MSI install work and even then, it says I doesn't have the rights to create a shortcut on the desktop. Don't know what I need to modify and where for that. I'm saying this because I don't know how MSE updates, but if they use MSI files to do that, that might explain things. The SYSTEM group remains added, but every time I take away the read only attribute, click OK and check the settings again, read-only is still active... That's all I know. Screenshot, all those updates were manual:

    Read the article

  • VMware and Windows Activation

    - by Peter M
    Yesterday I installed Slysoft's Virtual CloneDrive in order to mount an iso for some software installation on my host system (XP Pro SP3) This morning I fired up VMware and made a linked clone of an existing XP vm in order to do some software testing. This is the sort of thing that I do all the time, and the base XP vm that I clone was activated a long long time ago. The surprise today was that the newly cloned vm was no longer activated and XP cited major changes in hardware as the reason. I repeated the test with a full clone of the base system and got the same message. I then started up my base vm and it seemed to be activated, yet another vm (which I fully cloned from the base vm a long time ago) now started reporting that XP was not activated. At this point I guessed that Virtual DriveClone might have been the source of my hardware differences so I uninstalled it and rebooted. After this I made a new linked clone and full clone of the base vm and XP did not complain about not being activated. So I seem to be back to where I was before installing Virtual DriveClone with the exception that that one particular XP vm continues to complain about activation (even though 4 or 5 other XP vm's are fat and happy) Now to my questions: Why would adding Virtual CloneDrive to the host system affect XP activation on the vm's? From their point of view I would have thought that the environment had not changed as I had not enabled any new hard drives in their systems. Or is adding a hard drive to the host system enough to upset XP activation? Since this event, one of my fully cloned vm's is still reporting that XP is not activated even though I have removed Virtual CloneDrive. Is there anyway to convince XP that it is on the same system as yesterday? Or are my only options to do an activation or restore the vm from a previous backup?

    Read the article

  • 2008 Sever Randomly reboots.

    - by Jeff
    I'm out of ideas here. We have a 2008 Server that keeps rebooting 2-3 times a day at completely random times with an "Unexpected Shutdown" event. There are no Dumps, no events leading to it just like it loses power then comes back online. I ran a Diagnostic of the power supply and it has had continuous power for months. In addition, the temperature of the processors are maxing out at 40 degrees Celsius. Anyone have any ideas how to figure out why this is restarting all the time? This is a DMZed Web server so it doesn't do too much process wise. Here are the specs: Host Name: ~~~ OS Name: Microsoft Windows Server 2008 R2 Standard OS Version: 6.1.7600 N/A Build 7600 OS Manufacturer: Microsoft Corporation OS Configuration: Standalone Server OS Build Type: Multiprocessor Free Registered Owner: Windows User Registered Organization: Product ID: ~~~ Original Install Date: 5/27/2010, 4:25:47 PM System Boot Time: 2/14/2011, 5:35:01 PM System Manufacturer: HP System Model: ProLiant DL380 G6 System Type: x64-based PC Processor(s): 1 Processor(s) Installed. [01]: Intel64 Family 6 Model 26 Stepping 5 GenuineIntel ~1586 Mhz BIOS Version: HP P62, 8/16/2010 Windows Directory: C:\Windows System Directory: C:\Windows\system32 Boot Device: \Device\HarddiskVolume1 System Locale: en-us;English (United States) Input Locale: en-us;English (United States) Time Zone: (UTC-05:00) Eastern Time (US & Canada) Total Physical Memory: 4,086 MB Available Physical Memory: 2,775 MB Virtual Memory: Max Size: 8,170 MB Virtual Memory: Available: 6,691 MB Virtual Memory: In Use: 1,479 MB Page File Location(s): C:\pagefile.sys

    Read the article

  • Slow network file transfer (under 20KB/s) on newly built x64 Win7

    - by Mangoshake
    I am getting <20KB/s for local network file transfer. If I transfer a very small file (less than 100KB) it would start quickly then slow down to <20KB/s. all subsequently network file transfer would be slow, a reboot is needed to reset this. If I transfer a large file it would be stuck on calculating for a long time and then begin with <20KB/s immediately. This is a newly built desktop running Windows 7 x64 SP1. Realtek gigabit LAN from the motherboard (ASRock Extreme3 gen3). Problematic speed is observed on the private LAN, both through ethernet and WiFi. The Router is D-Link DIR-655. Remote Differential Compression is off. Drivers are up-to-date from ASRock's website. I have tested network file transfer to and from another Windows 7 laptop and a MacBook Pro, so I am fairly certain it is the desktop's problem. The slow speed only happens with one direction also, outbound from the desktop, regardless of whether I initiate the file transfer action from the origin or the destination. Inbound network file transfer and internet speeds are fine, so I don't think this is a hardware issue. I am getting 74.8MB/s internet upload speed from speedtest.net (http://www.speedtest.net/result/1852752479.png). Inbound network file transfer I can get around 10-15MB/s. I am hoping this community has some insight for me to troubleshoot this. I don't see anything obviously related from the Event Viewer, and beyond that I just don't know where else to look. Any suggestions are greatly appreciated, thank you in advance.

    Read the article

  • TFS 2012: Backup Plan Fails with empty log file

    - by Vitor
    I have a Team Foundation Server 2012 installation with Power Tools, and I defined a backup plan using the wizard found in the "Database Backup Tools" in the Team Foundation Server Administration Console. I set the backup plan to do a full database backup on Sunday mornings, to another server in the network. I followed the wizard with no problems and the Backup Plan was set successfully. However when the backup runs it returns Error as result and when I go to the log file I only get the header and no further info: [Info @01:00:01.078] ==================================================================== [Info @01:00:01.078] Team Foundation Server Administration Log [Info @01:00:01.078] Version : 11.0.50727.1 [Info @01:00:01.078] DateTime : 11/25/2012 02:00:01 [Info @01:00:01.078] Type : Full Backup Activity [Info @01:00:01.078] User : <backup user> [Info @01:00:01.078] Machine : <TFS Server> [Info @01:00:01.078] System : Microsoft Windows NT 6.2.9200.0 (AMD64) [Info @01:00:01.078] ==================================================================== I can imagine it's a permission problem, but I have no idea where to start ... Can anyone help? Thank you for your time! EDIT I'm not sure if it is related, but I logged in with "backup user" in "TFS Server" and there was this crash window opened with "TFS Power Tool Shell Extension (TfsComProviderSvr) has stopped working". The full crash log is here: Problem signature: Problem Event Name: APPCRASH Application Name: TfsComProviderSvr.exe Application Version: 11.0.50727.0 Application Timestamp: 5050cd2a Fault Module Name: StackHash_e8da Fault Module Version: 6.2.9200.16420 Fault Module Timestamp: 505aaa82 Exception Code: c0000374 Exception Offset: PCH_72_FROM_ntdll+0x00040DA8 OS Version: 6.2.9200.2.0.0.272.7 Locale ID: 1043 Additional Information 1: e8da Additional Information 2: e8dac447e1089515a72386afa6746972 Additional Information 3: d903 Additional Information 4: d9036f986c69f4492a70e4cf004fb44d Does it help? Thanks everyone!

    Read the article

  • IIS 7.5 FTP Service crashes after installation of Advanced Logging 1.0 Module

    - by Jeremy
    I've recently been tasked with setting up two new productions servers for an ASP.Net application. The servers sit behind a F5 Load Balancer, which in turn forwards the end users IP address forward via the standard X_Forwarded_For HTTP Header. All of the reading that I have done suggests that I need to install the IIS Advanced Logging Module in order to take advantage of the X_Forwarded_For HTTP Header. Some quick background: Both of the web servers are Windows 2008 R2 Standard (x64), with IIS 7.5 installed and configured. The FTP Role has also been installed, configured and is operational. The Issue After installing the IIS Advanced Logging module via the Web Platform Installer, I noticed the following Error in the Event Viewer: The FTP Service encountered an error trying to read configuration data from file \?\C:\Windows\system32\inetsrv\config\applicationHost.config, line number 374. The error message is: Unrecognized element 'advancedLogging' Trying to connect over FTP to either of the web servers results in a 530. I've spent 2 hours scouring Google trying to find a solution, short of uninstalling the Advanced Logging Module. As far as I can tell, there is no way to turn off Advanced Logging on a site per site basis. Help would be appreciated.

    Read the article

  • Cannot click send button in Outlook (+ Exchange) for unknown addresses

    - by Graphain
    Hi, I have a very unusual problem. I have Outlook 2010 connected to Exchange 2010. This can send emails perfectly to known addresses (that is, addresses in the address book or ones that have been sent to previously). However, if I put in an address that is unknown, I cannot actually click the Send button in Outlook. (it simply does nothing). Corresponding to this I get errors in the Event Log for each Send click stating "The connection to Microsoft Exchange is unavailable. Outlook must be online or connected to complete this action.". However, Outlook shows as connected the whole time, pings do not break, and I have no reason to suspect it has lost connection. To further complicate matters, Outlook is fine on all other PCs, and this was all perfect until I installed BitDefender on the PC in question and the Exchange Server. Outlook was still fine on these other PCs while BitDefender was installed, but I have removed it from the PC in question and the Server just in case (no success). Summary: Outlook encounters Exchange connectivity issues when sending to unknown (new) email addresses that prevent the Send button actually working at all. This is isolated to one machine and occurred after installation of AV/Firewall software which has since been thoroughly removed. If you have any potential solutions I'd love to hear them, as I will be resorting to reformatting the PC in question, and probably removing Exchange because I'm sick of its issues if I cannot resolve this soon. Big thanks for any help.

    Read the article

  • Issues installing apache debian

    - by Belgin Fish
    I'm having issues installing apache2, and pretty much everything in general, I'm using debian. I run sudo apt-get install apache2 and then it returns root@debian:~# apt-get install apache2 Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: apache2 : Depends: apache2-mpm-worker (= 2.2.16-6+squeeze7) but it is not going to be installed or apache2-mpm-prefork (= 2.2.16-6+squeeze7) but it is not going to be installed or apache2-mpm-event (= 2.2.16-6+squeeze7) but it is not going to be installed or apache2-mpm-itk (= 2.2.16-6+squeeze7) but it is not going to be installed Depends: apache2.2-common (= 2.2.16-6+squeeze7) but it is not going to be installed E: Broken packages Not really sure what's up :S Seems like it can't find any of the required packages for anything, Anyone know what I'm doing wrong?

    Read the article

  • Remote Desktop to Server 2008 fails from one particular Win7 client

    - by Jesse McGrew
    I have a VPS running Windows Web Server 2008 R2. I'm able to connect using Remote Desktop from my home PC (Windows 7), personal laptop (Windows 7), and work laptop (Windows XP). However, I cannot connect from my work PC (Windows 7). I receive the error "The logon attempt failed" in the RDP client, and the server event log shows "An account failed to log on" with this explanation: Subject: Security ID: NULL SID Account Name: - Account Domain: - Logon ID: 0x0 Logon Type: 3 Account For Which Logon Failed: Security ID: NULL SID Account Name: username Account Domain: hostname Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc0000064 Process Information: Caller Process ID: 0x0 Caller Process Name: - Network Information: Workstation Name: JESSE-PC Source Network Address: - Source Port: - Detailed Authentication Information: Logon Process: NtLmSsp Authentication Package: NTLM Transited Services: - Package Name (NTLM only): - Key Length: 0 I can connect from the offending work PC if I start up Windows XP Mode and use the RDP client inside that. The server is part of a domain but my account is local, so I'm logging in using a username of the form hostname\username. None of the clients are part of a domain. The server uses a self-signed certificate, and connecting from home I get a warning about that, but connecting from work I just get the logon error.

    Read the article

  • "Server Unavailable" and removed permissions on .NET sites after Windows Update [closed]

    - by andrewcameron
    Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

    Read the article

  • Formatting an external HDD stuck at 70%

    - by mahmood
    My external HDD which is a 250GB WD (powered by USB) seems to have problem! Whenever i try to copy some files, it stuck while copying. I decided to format it. So I used windows tool and performed the format (not quickly) however at nearly 70% it stuck. Then I decided to perform a low level format with lowlevel. Again it stuck at 70%. I endup that the HDD has bad sector. So is there any tool that mark the bad sectors and bypass them? It is not very reasonable to through 250GB because of some bad sectors! P.S: I saw a similar topic but there were no conclusion there either. The smart data is Attribute, raw value, value, threshold, status Read Error Rate, 50, 200, 51, OK Spin-Up Time, 3275, 154, 21, OK Start/Stop Count, 2729, 98, 0, OK Reallocated Sectors Count,0, 200, 140, OK Seek Error Rate, 0, 100, 51, OK Power-On Hours (POH), 1057, 99, 0, OK Spin Retry Count, 0, 100, 51, OK Recalibration Retries ,0, 100, 51 , OK Power Cycle Count, 1385, 99, 0, OK Power-off Retract Count, 425, 200, 0, OK Load /Unload Cycle Count,12974, 196, 0, OK Temperature, 43, 43, 0, OK Reallocation Event Count,0, 200, 0, OK Current Pending Sector Count,23,200, 0, Degradation Uncorrectable Sector Count, 0, 100, 0, OK UltraDMA CRC Error Count,6, 200, 0, OK Write Error Rate/Multi-Zone Error Rate,0,100,51, OK It seems that the most important thing is this line Current Pending Sector Count,23,200, 0, Degradation Any idea on that?

    Read the article

  • filesystem compatible with freenas and windows

    - by Daniel
    Hi all, I'm planning on using FreeNAS (was considering openfiler but freenas seems simpler) for my home NAS box running off ESXI. I have managed to get local sata drives to mount in ESXI (http://serverfault.com/questions/216902/esxi-add-datastore-without-partitioning). I've had one of the drives fail on my before and I was able to retrieve most of the data off it using windows tools (I'm not much of a linux guy I know enough to be dangerous!). If I go the freenas route in the event that something goes bad what would be the best file system to use so that I could pop the drive out of the freenas box (vm) and put it in another pc running windows so I could try and run various recovery tools to get the data back. All in all its not a major problem if I lose the data just would be a bit annoying, so I'm not looking for suggestions around backing up etc. I was considering using NTFS that the drives are already formatted as but it appears that while freenas does support NTFS that its a bit buggy and not 100% reliable, anyone know if this is still true? Read that on a forum somewhere.

    Read the article

  • Can't set screen brightness in Gentoo system

    - by Real Yang
    My system: Linux gentoo 3.10.7-gentoo-r1 VGA compatible controller: NVIDIA Corporation GT216M [GeForce GT 240M] (rev a2) output of xbacklight: No outputs have backlight property output of xrandr: xrandr: Failed to get size of gamma for output default Screen 0: minimum 640 x 480, current 1280 x 720, maximum 1280 x 768 default connected 1280x720+0+0 0mm x 0mm 1280x720 0.0* 1024x768 61.0 800x600 61.0 640x480 60.0 1280x768 0.0 output of ls /proc/acpi: button/ event When I'm in kernel 3.8.13, I can change my brightness using xbacklight. I compiled 3.10.7-r1 using genkernel all. Before the upgrade I did get a notice of "compatible issues for Nvdia users" from emerge but I still don't know the details. It there anyway to let me set the brightness? Then i found a ebuild app-laptop/nvdiabl-0.81 and tried to emerege nvidabl, I got this message: Your kernel does not support FB_BACKLIGHT. To enable you it you can enable any frame buffer with backlight control or nouveau. Note that you cannot use FB_NVIDIA with nvidia's proprietary driver Please check to make sure these options are set correctly. Failure to do so may cause unexpected problems. Once you have satisfied these options, please try merging this package again. ERROR: app-laptop/nvidiabl-0.81::gentoo failed (pretend phase): Incorrect kernel configuration options Call stack: ebuild.sh, line 93: Called pkg_pretend nvidiabl-0.81.ebuild, line 31: Called linux-mod_pkg_setup linux-mod.eclass, line 559: Called linux-info_pkg_setup linux-info.eclass, line 911: Called check_extra_config linux-info.eclass, line 805: Called die The specific snippet of code: die "Incorrect kernel configuration options" [SOLVED] I enter the menuconfig again and check the Device Drivers -> Graphics support -> Support for frame buffer devices, then i found this: <*> nVidia Framebuffer Support [*] Support for backlight control (NEW) What can i say. Recompiling...

    Read the article

  • How to diagnose occasional sudden resets?

    - by steve314
    I have a Windows XP system, and have recently upgraded by adding 2 1GB sticks of RAM to the 2x0.5GB already present. Since then, about once per day (the system is used 8+ hours per day), the system has suddenly and unexpectedly reset. On a couple of occasions, the system has frozen completely, only responding to the power button being held in for several seconds to force power off. Nothing at all ever appears in the system event log that might indicate a possible cause - everything seems to suggest business as usual. Sounds like faulty memory - but memtest86+ says otherwise. A full test, taking over an hour, found no issues. The next likely suspicion, then, is that I've knocked something while installing the RAM. Trouble is, everything I can think of to test seems fine. I've opened up the case and prodded a few things around, hoping to get better contact on connections etc, but there's no sign yet as to whether that has made a difference or not. I thought about a malware-related timing fluke, but again, so far as I can tell I'm all clear. All I can think of to add to my checklist (mainly of things that I can't easily check) is... The power supply is (1) only 350W, (2) not necessarily the best quality, and (3) powering a Prescott P4 640 3.2GHz. Could that be borderline overloaded or about to die? How do I check? Is it possible that the CPU isn't getting cooled properly? I haven't had the fan past normal tickover even doing video encoding, and the only sane temperature reading from SpeedFan is pretty steady at 36 celcius, so probably not. Any thoughts? Is there a standard procedure for diagnosing this kind of fault?

    Read the article

  • Win2008/IIS7/fx2.0 - 500.19 error

    - by Keith Barrows
    I installed new boxes at the beginning of the week. 1) Web Server on Win2008 x64, IIS 7 + all updates 2) DB Server on Win2008 x64, SQL 2008 Ent + all updates I configured my websites, set up host headers and DNS entries, worked through some problems on my handlers and finally got it all running Wednesday morning. Our team has been using it since then. This morning I came in and everyone of us is getting a 500 error. Error Summary HTTP Error 500.19 - Internal Server Error The requested page cannot be accessed because the related configuration data for the page is invalid. Detailed Error Information Module IIS Web Core Notification Unknown Handler Not yet determined Error Code 0x80070005 Config Error Cannot read configuration file due to insufficient permissions Config File \?\C:\RivWorks\dev\web.config Requested URL http://dev.rivworks.com:80/login.aspx Physical Path Logon Method Not yet determined Logon User Not yet determined Config Source -1: 0: Links and More InformationThis error occurs when there is a problem reading the configuration file for the Web server or Web application. In some cases, the event logs may contain more information about what caused this error. I’ve gone through the KB articles, made sure IIS_IUSRS had read permissions and am now stumped. What bothers me is IIS is looking in \?\C:\ instead of just C:. What is happening? TIA

    Read the article

  • Exchange MSExchangeIS Mailbox Store Error

    - by Bart Silverstrim
    Boss asked me to check to see if I could figure out why he's had to restart the services on the Exchange server three mornings in a row now. While going through the system logs I ran across an error from the MSExchangeIs Mailbox Store, category General, Event 9690. The message said (edited to make generalized): Exchange store 'First Storage Group\Mailbox Store (Servername)': The logical size of this database (the logical size equals the physical size of the .edb file and the .stm file minus the logical free space in each) is 22GB. This database size has exceeded the size limit of 22 GB. This database will be dismounted immediately. Hmm...happened at five in the morning, and I'm thinking this is a pretty good hint that this leads to the culprit. Thing is I'm not an Exchange expert, so I'm still googling around to figure out how to fix the problem. Any better guidance out there? Or am I barking up the wrong binary tree? Exchange System Manager reports that the server is "version 6.5 build 7638.2, SP2", standard, which I believe is Exchange 2003. It's running on Windows Server 2003 R2 Standard, SP2.

    Read the article

  • Apache2.2 not responding on Windows 7 desktop

    - by Adam
    Afternoon! I'm having some trouble with Apache2.2 on Windows 7. For over a year it's been running no problem, but all of a sudden requests have just stopped responding. They don't ever time out, the browser just keeps on waiting for a response, which makes me think it's something blocking communication with Apache. Interestingly though, if I stop Apache the requests fail immediately. The Apache service is running, and using netstat I can see it listening on port 80 as configured: TCP 127.0.0.1:80 0.0.0.0:0 LISTENING If I stop the Apache service, that line disappears. I have an entry within my hosts file for each VHost I'm trying, all pointing to 127.0.0.1. Each VHost is configured to *:80. Nothing however is getting recorded in the access or error (at debug level) log files. I've verified the file paths are correct, even though they were never changed. Neither is anything getting recorded within Windows' Event Log. The problem showed up when I added a new VHost and restarted, however I hadn't been using it for a couple of days prior so I don't believe it's the config change. I have performed a syntax check to be sure, and when starting from the command prompt no errors are reported there. I do have Windows Firewall running, however I've verified the Apache rule is correct and tried turning it off to ensure that wasn't the problem. I've reinstalled Apache, in the hope it might magically fix something using the default config, but still no joy. I've also tried using a different port. I'm completely lost for ideas now. Can anybody help? Cheers Adam

    Read the article

  • Durability of Websockets Server

    - by smitchell360
    I am starting to experiment with websockets. Does anyone know of a websockets server (open source or paid) that provides a durable store of the websocket "channel"? All of the examples that I have found do not address durability -- if a websockets server goes down, all "channel" data is lost. Services such as Pusher do not really discuss whether they address the durability issue (and I have not received a response from tech support yet). Happy to roll my own, but would rather not reinvent the wheel. EDIT: I'm not looking for websockets 101 information. That is readily available and understood. I'm looking for a server (open source or paid) that supports websockets and has a durable store for the websocket data so that, in the event that a server fails, a new server can take over where the original one left off. Two main purposes: 1. support failover scenarios contemplated by the websockets Network Working Group http://tools.ietf.org/html/draft-ibc-websocket-dns-srv-02#section-5.1 (most importantly so that missed messages are sent when a client connects to a failover server) 2. support scenarios where new subscribers must receive all past messages that were published. Of course this can be handled at the application layer...but that is not what I am looking for.

    Read the article

  • Exchange 2010 Hub cannot deliver to Exchange 2007 Hub - "451 5.7.3 Cannot achieve Exchange Server authentication"

    - by Graeme Donaldson
    We have an existing Exchange 2007 server in Site A (exch07). I've installed an Exchange 2010 server in Site B (exch10). Both servers have the CAS, Mailbox and Hub roles. Messages sent via SMTP on exch10 which are destined for mailboxes on exch07 are queued with the "Last Error" reported in Queue Viewer as '451 4.4.0 Primary target IP address responded with: "451 5.7.3 Cannot achieve Exchange Server authentication." Attempted failover to alternate host, but that did not succeed. Either there are no alternate hosts, or delivery failed to all alternate hosts.' I've found that some people have resolved this by creating new Receive Connectors which are scoped specifically to apply to connections from the remote hub/s, but I have had no luck doing this. Specifically I created new receive connectors on both servers with the following settings: Remote IP = IP/s of remote server Authentication = "Transport Layer Security (TLS)" and "Exchange Server authentication" Permission Groups = "Exchange servers" and "Legacy Exchange Servers" This made no difference, I see the same error message. What am I missing? Update: We noticed that the Application log had this error message from MSExchangeTransportService: Microsoft Exchange could not find a certificate that contains the domain name exch07.domain.local in the personal store on the local computer. Therefore, it is unable to support the STARTTLS SMTP verb for the connector exch10 with a FQDN parameter of exch07.domain.local. If the connector's FQDN is not specified, the computer's FQDN is used. Verify the connector configuration and the installed certificates to make sure that there is a certificate with a domain name for that FQDN. If this certificate exists, run Enable-ExchangeCertificate -Services SMTP to make sure that the Microsoft Exchange Transport service has access to the certificate key. It turns out that the default self-signed certificate was no longer enabled for the SMTP service for some reason. After enabling the self-signed certificate for SMTP, we no longer get the error in the event logs, but delivery is still failing with the same error message. Update 2: I put a mailbox on exch10 and attempted to deliver a message via SMTP on exch07 and I get the same error.

    Read the article

  • Windows 2008 64bit: applications and explorer always hang

    - by Phil Farthing
    I setup a couple of Window 2008 64bit systems about 5 months ago. Initially all seemed well. Now however, for no apparent reason, things are dog slow, apps hang, explorer hangs, just clicking on something can cause a CPU spike of 100%, and often it's explorer that is eating it up. As I have two on identical hardware, and they experience the same problem, it doesn't seem related to addon software. The only thing these have in common is Kaspersky and I've tried disabling/uninstalling to no avail. There are no useful error messages in the event logs. Actually, the system never even reports app hangs. Sometimes, it similar to what I've seen on Windows 7 systems where the screen goes milky and asks if I want to trouble shoot, that's only when get impatient and click happy. The really odd thing, is that it will NOT do this for a few minutes at a time, and then starts up again. Like I will click on the start menu and browse for the Admin Tools, the start menu will hang at some point and I'll have to wait about a minute, then it's OK. The next time I do this, a few seconds later, it's fine. Every click seems to hang the first time around, then be ok the second time if I do the exact same thing. If anyone has any suggestions, please PLEASE let me know! thanks =)

    Read the article

  • Active Directory Child Domain Replication Problems

    - by MikeR
    Hi, I've recently inherited an Active Directory (all DCs Windows 2003) which has been configured with several child domains that are used as test environments for out CRM software. Two of these child domains have been used for testing using dates in the future (2015), throwing them well outside of the Kerberos tolerance for time, and they're flooding my event logs with replication errors such as the following: Description: The attempt to establish a replication link for the following writable directory partition failed. Directory partition: CN=Schema,CN=Configuration,DC=ad,DC=xxxxxxx,DC=com Source domain controller: CN=NTDS Settings,CN=TESTDC001,CN=Servers,CN=SiteName,CN=Sites,CN=Configuration,DC=ad,DC=xxxxxxx,DC=com Source domain controller address: 38e95b2a-35af-4174-84ba-9ab039528cce._msdcs.ad.xxxxxxx.com Intersite transport (if any): This domain controller will be unable to replicate with the source domain controller until this problem is corrected. User Action Verify if the source domain controller is accessible or network connectivity is available. Additional Data Error value: 5 Access is denied. I'd also like to upgrade to Windows 2008 at some point, but wouldn't want to attempt any schema updates while I'm not 100% confident on the replication. I'm guessing my only real solution will be to get rid of these child domains. The child domains are operating as stand alone domains, the DC is up and running and authenticating test users fine. I'm guessing the best solution to this would be to delete the domains (although I'd be happily told otherwise). The clock forwarding appears to have been happening for several years, so I'm assuming I can't just put the clock right (I'm guessing scope for this would be 180days, the same as the tombstone lifetime) With the replication errors would I be able to dcpromo the child domains DC, select it as the last domain controller in the domain and the child domain would be deleted? Or would I be better off treating the domain as an orphaned domain and use Microsoft's instructions to clear up as such. Any advice would be much appreciated.

    Read the article

  • Suspected brute force attack

    - by HarveySaayman
    Recently I acquired a dedicated server from a local ISP to play around with. As the tags suggest, its a windows server 2008 R2 machine. I've only had it for a few days, and no real traffic is going to it yet. I haven't even deployed a "real" website to it yet. Just a silly page so that I could check IIS, my host headers, DNS records, etc are all configured correctly. While playing around, I noticed a ton of Audit Failure entries in the event viewers security logs. It seems something is trying to access the administrator account, and failing. It smells like a brute force attack to me. My ISP gave me the account details of the administrator account and I used those to RDP into the box, which I've heard is not the securest of situations. I created myself another account and added myself to the administrator group, so im using that account to gain acceess to the machine now. In response to all of this i used http://strongpasswordgenerator.com/ to generate me some 20 character length strong passwords and changed all of my account passwords, even the SQL sa user. I also enabled the auto ban feature of FileZillaServer (my FTP server) My questions: 1) how can i detect this kind of thing better? 2) how can i protect my server from unauthorized access better? PS: I'm a software dev, not a sysadmin so please mind my server security idiot-ness-ness

    Read the article

  • Mail to Mailenable group sometimes bounces back because it cannot find one of the group members

    - by Stanley
    I am using MailEnable Enterprise Edition 6.53. On one of my PostOffices I have a group address set up with 5 members in the group. Under normal circumstances when someone sends a mail to this group then the mail gets successfully forwarded to all 5 members in the group. However, every now and then when a recipient sends to the group they get a bounce back message from us that the mail could not be delivered because one of the user's addresses was not found on the server. This could happen for any one of the 5 users in the group. The error message looks like: Message could not be delivered. Error was: The email address is not available on this system The following recipient(s) could not be reached: [SF:mydomain.com/my_username] What could be causing this and how do I fix it? Obviously the mailbox DOES exist as, under normal circumstances, when someone mails the group the mail gets delivered successfully and forwarded to all group members. All the mailboxes most definitely DO exist on the system. EDIT: I have done more investigation and I see an error in Windows Event Viewer: MailEnable Database Provider error: 0 FAILURE: (SQLDriverConnect), Module: MEIMAPS.exe; Error: [Microsoft][ODBC SQL Server Driver]Timeout expired This seems to be related to http://forum.mailenable.com/viewtopic.php?p=53157 and http://www.mailenable.com/kb/content/view.asp?ID=ME020535 but the setups in these links use MySQL as a database whereas we use SQL Server. Maybe this shines some new light on the problem?

    Read the article

< Previous Page | 522 523 524 525 526 527 528 529 530 531 532 533  | Next Page >