Search Results

Search found 18092 results on 724 pages for 'matt long'.

Page 533/724 | < Previous Page | 529 530 531 532 533 534 535 536 537 538 539 540  | Next Page >

• Is there a realiable way to troubleshoot wake up from sleep in Windows?

  - by Borek

  Is there a reliable way to troubleshoot laptop wakes? I've seen "heuristics" posted here and there but isn't there really a simple and deterministic way to tell what's causing a problem? Specifically, my laptop wakes up about every hour for about 2 minutes. Exported event log entries are here: http://www.mediafire.com/?abcqb00v5wyo6pj. I've tried: powercfg -devicequery wake_armed Empty result set. Scheduled tasks - the main ones are not scheduled to run every hour. When go through a long list of all possible tasks, there are some that are set to be triggered every hour (e.g., MS "RacTask" whatever it is). But when I go to power options, Advanced settings, Sleep, Allow wake timers it is set to "Disable". Also, the specific task is not set to wake the computer if necessary. Power options for my Ethernet card don't enable it to wake the computer - the cable is disconnected anyway. There are no other HW devices attached - no USB disks, no keyboards / mice etc. I am really clueless and quite unhappy that it's so hard to troubleshoot this situation.

  Read the article

• IPC between multiple processes on multiple servers

  - by z8000

  Let's say you have 2 servers each with 8 CPU cores each. The servers each run 8 network services that each host an arbitrary number of long-lived TCP/IP client connections. Clients send messages to the services. The services do something based on the messages, and potentially notify N1 of the clients of state changes. Sure, it sounds like a botnet but it isn't. Consider how IRC works with c2s and s2s connections and s2s message relaying. The servers are in the same data center. The servers can communicate over a private VLAN @1GigE. Messages are < 1KB in size. How would you coordinate which services on which host should receive and relay messages to connected clients for state change messages? There's an infinite number of ways to solve this problem efficiently. AMQP (RabbitMQ, ZeroMQ, etc.) Spread Toolkit N^2 connections between allservices (bad) Heck, even run IRC! ... I'm looking for a solution that: perhaps exploits the fact that there's only a small closed cluster is easy to admin scales well is "dumb" (no weird edge cases) What are your experiences? What do you recommend? Thanks!

  Read the article

• How to set up mysql storage for certain rsyslog input matches?

  - by ylluminate

  I'm draining various logs from Heroku to an rsyslog linux (ubuntu) server and am starting to have a little more to bite off than I can chew in terms of working with my log histories. I am needing to be able drill back in time based on more flexible details and more flexible access than what the standard syslog file(s) provide. I'm thinking that logging to mysql may be the correct approach, but how do I set this up such that it pulls only certain log entries into a table based on an identified? For example, I see a long hex string identifying each log entry from a certain Heroku app instance. I assume that I can just pipe those into the mysql socket vs ALL rsyslog input into mysql... Could someone please direct me to a resource that can walk me through the process of setting something like this up or simply provide some details that can help? I have 15+ years of Unix experience so I just need some nudging in the right direction as I've not really done a tremendous amount of work with syslog daemons previously in terms of pooling various servers into one. Additionally, I'd be interested in any log review tools that could make drilling through log arrangements like this more handy for developers.

  Read the article

• Windows 7 ssh file server.

  - by Siriss

  Hello all- I have looked at the other posts, but have not quite found an answer I have a question about windows file sharing over SSH. I have copssh installed and it is working for Remote desktop connections. I have port 22 forwarded on my router etc. I connect from a Mac or Putty with this address: ssh -l copsshusername 3391:localhost:3389 [external ip] That works fine. I would like to configure Windows 7 to allow my ssh account that I use to login, access to certain shared folders. I have documents and videos and things that I would like to be able to download externally. I have done this before on Linux and a long time ago on XP, but I cannot figure out what I am missing on Windows 7. There is a designated SSH user that copssh uses to run the service and that I use to to login as. I have googled and googled and have not found a solution that does everything I need that is why I am turning here for ideas. I hope I am explaining this correctly. Thank you very much for your help!

  Read the article

• How to encourage Windows administrators to pick up scripting

  - by icelava

  When i worked as an administrator in my first job, I was frustrated our administration processes with Windows servers were a series of point-and-clicks; we could never match the level of efficiency with the Unix servers which had a group of shell scripts to automate a lot of the work. I soon read about WSH and ADSI and wasted no time learning just how much automation I was able to achieve with scripting. There was a huge problem though - almost none of my Windows colleagues were really interested in learning scripting. They seemed happy with the manually mouse-clicking chores and were never excited at the prospect of using scripts to do the work on their behalf. I struggled to convince them to pick up scripting skills despite the evident increases in efficiency. I left that job in pursuit of a full-time software development career thereafter. Almost a decade on working in various environments and different customers, I still encounter Windows administrators mainly possessing this general "mood" where they would avoid scripting as much as possible. Despite the increasing level of accessibility Windows server technologies are opening up for scripting and automation. I am almost certain the majority of administrators are administrators precisely because they absolutely hate performing any kind of programming duties. What are some means to encourage and motivate administrators that scripting can really help them in the long run?

  Read the article

• Is it possible to download extremely large files intelligently or in parts via SSH from Linux to Windows?

  - by Andrew

  I have a ~35 GB file on a remote Linux Ubuntu server. Locally, I am running Windows XP, so I am connecting to the remote Linux server using SSH (specifically, I am using a Windows program called SSH Secure Shell Client version 3.3.2). Although my broadband internet connection is quite good, my download of the large file often fails with a Connection Lost error message. I am not sure, but I think that it fails because perhaps my internet connection goes out for a second or two every several hours. Since the file is so large, downloading it may take 4.5 to 5 hours, and perhaps the internet connection goes out for a second or two during that long time. I think this because I have successfully downloaded files of this size using the same internet connection and the same SSH software on the same computer. In other words, sometimes I get lucky and the download finishes before the internet connection drops for a second. Is there any way that I can download the file in an intelligent way -- whereby the operating system or software "knows" where it left off and can resume from the last point if a break in the internet connection occurs? Perhaps it is possible to download the file in sections? Although I do not know if I can conveniently split my file into multiple files -- I think this would be very difficult, since the file is binary and is not human-readable. As it is now, if the entire ~35 GB file download doesn't finish before the break in the connection, then I have to start the download over and overwrite the ~5-20 GB chunk that was downloaded locally so far. Do you have any advice? Thanks.

  Read the article

• What performance degradation to expect with Nginx over raw Gunicorn+Gevent?

  - by bouke

  I'm trying to get a very high performing webserver setup for handling long-polling, websockets etc. I have a VM running (Rackspace) with 1GB RAM / 4 cores. I've setup a very simple gunicorn 'hello world' application with (async) gevent workers. In front of gunicorn, I put Nginx with a simple proxy to Gunicorn. Using ab, Gunicorn spits out 7700 requests/sec, where Nginx only does a 5000 request/sec. Is such a performance degradation expected? Hello world: #!/usr/bin/env python def application(environ, start_response): start_response("200 OK", [("Content-type", "text/plain")]) return [ "Hello World!" ] Gunicorn: gunicorn -w8 -k gevent --keep-alive 60 application:application Nginx (stripped): user www-data; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; } http { sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; upstream app_server { server 127.0.0.1:8000 fail_timeout=0; } server { listen 8080 default; keepalive_timeout 5; root /home/app/app/static; location / { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_pass http://app_server; } } } Benchmark: (results: nginx TCP, nginx UNIX, gunicorn) ab -c 32 -n 12000 -k http://localhost:[8000|8080]/ Running gunicorn over a unix socket gives somewhat higher throughput (5500 r/s), but it still does't match raw gunicorn's performance.

  Read the article

• How to send from my Z88 to my PC

  - by Bevan

  I've got a Cambridge Z88 that I want to get working with my PC. Around 6 years ago - in 2004 - I made heavy use of my Z88 to do a whole bunch of writing on the train while commuting to and from work. The Z88 is solid state, lightweight and has a full size silent keyboard, so it works very well as a writing instrument. I still have the serial cable I soldered up back then and used successfully in 2004. It has these connections: Z88 9 pin ----- ------- 2 TxD ------> RxD 2 3 RxD <------ TxD 3 7 GND <-----> GND 5 4 RTS ------> CTS 8 5 CTS <-+ RTS 7 8 DCD <-+---- DTR 4 9 DTR ----+-> DCD 1 +-> DSR 6 Unfortunately, I haven't been able to find my notes from 2004 that describe how I got it to work back then. I've spent several hours trying to Google a result, but to no avail. I'm pretty sure the cable is fine - after all, it's what I used successfully six years ago, and I've checked it out with a multimeter - so I'm focusing on the PC end of things, which is where I'd like some assistance. Q1: In my recent attempts, I've been using both Hyperterminal (as built into Windows XP) and the command line (copy com2: con:), but with no success. What's a good (better!) serial communications application to use? Is there one that allows me to see as deep as the signalling that's occurring on the wire? Q2: If you have a Z88 that works correctly with your PC, what software do you use on the PC end, and what's the pinout of your cable? I'm pretty sure that the Z88 itself is working properly: When using the built in Import/Export tool to send a file, I see different behaviour when my serial cable is connected compared to disconnected. When disconnected, the transmission appears to work, with a progress meter counting up and then finishing; when connected, nothing happens 'cept a timeout if I wait long enough.

  Read the article

• Ubuntu 12.04 open port 80 inside WLAN

  - by Eduard

  I have an nginx server running on ubuntu 12.04 that serves http through port 80 and https through port 443. Everything works fine if I access it from the same computer via localhost, 127.0.0.1 or the local IP 192.168.0.11. If I try to access the server from another computer in the same VLAN it does not work for http; it works for https. I have changed my nginx configuration to also listen to port 8000 for http; I can then access http from the other computer in the same VLAN via "http://192.168.0.11:8000". I also have a web server running on port 80 on a windows machine and can access it from another device in the same VLAN, therefore the router is not blocking incoming http traffic. The nginx process is run by root. I have used tcpdump and I see that packets are arriving to Ubuntu: 192.168.0.16.49735 192.168.0.11.80 and that some response is being given 192.168.0.11.80 192.168.0.16.49735 (I do not know what the response is though). There is no request arriving at the nginx web server (I have checked the access log). I have iptables empty. I have unsuccessfully tried to find a solution for a long time to this, it has now become a matter of happiness or bitterness :).

  Read the article

• Ubuntu Natty 11.04, Turning the wireless switch off; switches it off permanently!

  - by ZiGi

  i'm using an hp pavilion dv2000 i turned the wifi switch off by mistake, the LED turned orange and the wifi got disconnected. and now when i turn the switch on, it remains orange and the wifi still isn't functional. this happened before; i found a fix that worked searching google. it was done via terminal commands and i didn't have to download anything but i can't find the solution anymore! wlan0 shows up when i use: :~$iwconfig #BLA BLA BLA #... wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off more results: :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: yes Hard blocked: yes :~$ sudo rfkill unblock all :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: no Hard blocked: yes :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill it's still hard blocked! even though the switch is turned on; gives the same result eitherways a direction to a page with a working solution is a much appreciated answer!

  Read the article

• switchover in postgresql

  - by user1010280

  I am using Postgresql 9.0 with Streaming replication. So, during switchover I follow these steps:- Get the server timestamp on primary. Get the current log position on primary. Set Verify Log location Verify Transaction Received Location Shutdown DB on production. Synchronize the transaction logs from PR to DR. Trigger a failover on the DR Database by creating the trigger file specified in recovery.conf Verify DB Mode on DR Copy the control file from from DR to primary. copy the temporary stats file from DR to primary. copy the history file from DR to primary. Create recovery.conf file. Start Database in standby mode in primary. Verify DB mode on PR At step (6), I have to copy last wal generated on Primary to standby and sync both PR and standby. but this thing takes time to copy files because this remote. So that postgres will keep seraching for wal for long time and after that it stops the server. So I want to know is there any way so that I can ask postgres to stop seraching or locating WAL after shutdown??? because postgres tries to locate this wal every 5 seconds. Please reply as soon as possible..its urgent...

  Read the article

• Barriers to IPv6 deployment: addressing

  - by sysadmin1138

  There are several things that are keeping IPv6 deployment from being a topic of active discussion here at my work. There are the usual technical issues, but one non-technical one appears to be a major stumbling block on the path to actually getting a deployment project going. Addresses, memorizing of. Specifically, IPv4 addresses are comprehensible, and IPv6 addresses just look like a big long string of hex. The human mind has real trouble memorizing lists of more than 7-8 items, and an IPv4 address (192.168.231.148) has four items in it which makes it easy for us to memorize. A fully populated IPv6 address has not only 8 sections, but each section has 4 hex digits in it. IPv6 addresses were not designed for memorization. To the technician who knows that the DNS server is at 192.168.42.42 (or more likely "42.42", since the company prefix is likely memorized), the idea of memorizing an IPv6 address fills them with dread. Which in turn makes them much less enthusiastic about participating in an IPv6 deployment project. Because of how our network works we're not fully dynamic in terms of v4 addressing. We have several to many subnets that are entirely statically assigned for a variety of reasons, chief among them being that the overhead of static DHCP assignments is perceived as being too great. Also, some devices still aren't smart enough to pull DNS addresses out of DHCP while also having a static assignment, and therefore require manually configured DNS settings. Therefore, some v6 address memorization will have to be done. We're not under any mandate to get v6 out the door, so we don't have pressure from the top. However, it is time to start prepping our infrastructure to handle IPv6 even if we don't convert wholesale. For those of you who have been in IPv6-land for a while, what short-cut methods do you use to discuss or keep track of subnets and specific/critical IP addresses? If I can help reduce some of the dread surrounding IPv6 we might get the project going.

  Read the article

• Unable to Use Bluetooth Mighty Mouse or Wireless Keyboard with Boot Camp

  - by Kristopher Johnson

  I have Windows 7 64-bit running on a MacBook Pro in a Boot Camp partition. I am trying to pair with my Bluetooth Mighty Mouse and Apple wireless keyboard under Windows, but whenever I try to do so, here's what happens: While on the Add a device window, I turn on the mouse or press a key on the keyboard, and the mouse or keyboard shows up in the list of available devices. I click the device and then the Next button, and the window displays Connecting to device... Time passes. Eventually, I get this error message: Adding this device to this computer failed Adding the device failed resulting in an unknown error. The reported error code is 0x80070015. Contact your device manufacturer for assistance. I've run Windows Update and Apple Software Update. I've also tried reinstalling the drivers from the Snow Leopard DVD. The mouse and keyboard both work fine when I boot into Mac OS X. FWIW, after many, many repeated tries, I eventually got it to work. I don't know why. So while my problem is solved, I'd still like to get an "answer" as to why trial-and-error seems to be the only approach. The keyboard, in particular, was hard to get set up. A few times, Windows would apparently recognize it and prompt me to enter the pairing code, but then it would time out after a couple of seconds (not long enough to enter the code). Grrrr.

  Read the article

• Virtual Machine Network Services causes networking problems in Vista Enterprise 64 bit install

  - by Bill

  I have a Quad-core/8GB Vista Enterprise 64-bit (SP2) installation on which I installed Virtual PC 2007. I have a problem that is opposite of all that I found searching around the Internet--everybody has problems making network connections from their guest VM. When Virtual Machine Network Services is enabled in the protocol stack for my network card across a reboot, it causes access problems to the network. The amount of time to login in using a domain credentialed account is upwards of 3 minutes, then after reaching the desktop the network and sharing center shows that my connection to the domain is unauthenticated. Disabling and re-enabling the Virtual Machine Network Services (uncheck in network properties/apply/recheck/apply) fixes the problem. And as long as I have the VMNS disabled when I shutdown the restart runs smoothly. I just have to remember to enable after login and disable before shutdown. I have un-installed and re-installed Virtual PC 2007 multiple times with restarts between. The install consists of the SP1 + a KB patch for guest resolution fix. Any help would be greatly appreciated. Some additional information... At one point during my hairpulling and teethgnashing with this, I tried to ping my primary DC and observed some weird responses: (Our DC is 10.10.10.25, my dynamic IP was 10.10.10.203) Reply from 10.10.10.203, Destination host unreachable. Request timed out. Reply from 10.10.10.25: ... This is not consistently repeatable, but thought it might strike a chord with someone.

  Read the article

• Metacity/Compiz not staring upon Login Ubuntu 10.10

  - by Ryan Lanciaux

  TLDR: As of this afternoon, I do not have a window manager when I login to Ubuntu 10.10. I would like to have window manager on login without needing to add to startup. Just started using linux again as my home OS. (Used it for a long time years ago but been on windows up until this past weekend) so this may be kind of n00b-ish :) Anyways, up until today, everything on my machine was running okay. I did not have compiz running as the default wm because I'm running NVidia Drivers and Xinerama (and as I understand Xinerama & Compiz don't work well together). I made no changes to my xorg / etc but today when I logged in, I had to manually start metacity from command line to get any window manager. Really not sure what would be causing this or what I can do to get it working again. My xorg.conf is available here: https://gist.github.com/845618. My default Window Manager is set to /usr/bin/metacity in Configuration Editor under /desktop/gnome/applications/window_manager. p.s. Any tips on how to run 3 monitors where I can move windows between screens without Xinerama would be appreciated but that's prolly for another thread :)

  Read the article

• Connecting to unsecured wireless network

  - by Sanchez

  I would like to know what information is public and can be intercepted in a non-open, but unsecured wireless network. Moreover, is there anything I can do to make it more "secure", other than using https connection whenever possible. In more details, I recently discovered (with surprise) that the wireless network in my school is actually unsecured. Although not everyone can connect to it (you need a student ID), I am told that certain softwares like Wireshark would be able to intercept the data. Since I have been using the network for all private purposes (email, facebook etc), I do feel quite insecure now and would like to understand the situation a bit better. I installed Wireshark and tried to play with it but all I can see are something alien to me. In any case, all I see seems to come directly/indirectly from my IP address, and I have long thought that usually different computers in the same wireless network would be assigned different addresses. Am I wrong? If not, then I feel very confused about what information is actually being captured (potentially by other users in the network, since I don't think I could capture activities of others in the same network anyway), and whether it's safe to use the network at all. (Gambling on others in the same network showing good behaviour is apparently not an option.) Thank you.

  Read the article

• Erratic WiFi 2.4 GHz channel spikes, what gives?

  - by Francis W. Usher

  Sorry guys, first a gripe about my neighbor's WiFi access point (it is related): they totally hog the center nine 2.4 GHz channels (3-11), centered right at 7! I know the outer regions of the signal don't make as much of a difference, and technically they're running channels 5 & 9. Anyway, their signal is clearly interfering with mine, which is necessarily centered at 3 or 11 to evade their interference. I guess it's somewhat a case of access point envy: they happen to have both a stronger signal and a higher data rate, while occupying twice the band width that I do. Getting to the point, I've noticed that they tend to sit nice and pretty centered at 7, but they definitely auto-select their channel, and I've noticed that the auto-selection algorithm tends to shift towards the higher channels; hence I decided to pick channel 3, and I don't get so many intermittent lag spikes any more. Anyway, the thing that weirded me out was the reason they have to auto-select sometimes: unexplained, powerful (talking order of 0dB here), giant spikes of 2.4 GHz activity in consistent regions of the spectrum. I don't think it's just noise, since my wireless monitoring software is registering a MAC address, a manufacturer, and usually a fairly coherent ascii name... and it seems to be a fairly well-confined signal. But these signals are fairly common, and they do some weird stuff to my signal. So my question is what are these signals? Where are they coming from? Where are they going? Why are they so ridiculously strong? Why don't they ever last very long? Here's an inSSIDer screenshot I took, for your perusal. I am labeled with "me", my greedy neighbor labeled with "neighbor", and the 2 quasar signals are labeled with "WTF?".

  Read the article

• Connecting to same public IP from different locations yields different results

  - by DHall

  Since yesterday I've been unable to access one of my favorite time-wasting sites, boston.com. It starts to load but then it gets redirected to pagesinxt or something like that. After some investigation, I've narrowed it down to an issue with cache.boston.com, but only from my work location. I found the IP (216.38.160.107) , but even that doesn't work correctly from here at work. When I do a telnet 216.38.160.107 80 GET http://cache.boston.com/universal/css/hp_bgcom.css from another location, I get a nice long CSS, as expected. From here, I get an error (trimmed for size): HTTP/1.1 400 Bad Request Your request could not be processed. Request could not be handled This could be caused by a misconfiguration, or possibly a malformed request. For assistance, contact your network support team. Is there any way I can troubleshoot this further on my end? Tracert doesn't tell me anything too useful: Tracing route to vwrpx1.ttn.xpc-mii.net [216.38.160.107] over a maximum of 30 hops: 1 * * * Request timed out. Since it's not really work-related, I don't really want to bring it up to our network team unless I know what's going on, or if there's some risk to the network (ex. malware or something)

  Read the article

• Sane patch schedule for Windows 2003 cluster

  - by sixlettervariables

  We've got a cluster of 75 Win2k3 nodes at work in a coarse grained compute cluster. The cluster is behind a mountain of firewalls and resides in its own VLAN. Jobs of all sizes and types run on the cluster and all of the executables running are custom-made. (ed: additional notes on our executables) The jobs range from 30 seconds to 7 days in duration, and may contain one executable or 2000 sub-jobs (of short duration). Obviously we are trying to avoid the situation where our IT schedules a reboot during a 7 day production job. We have scheduling software which accomodates all of the normal tasks for a coarse grained cluster and we can control which machines are active for submission, etc. If WSUS was in some way scriptable (or the client could state it's availability for shutdown) we could coordinate the two systems and help out. Currently, the patch schedule is the Sunday after Super Tuesday regardless of what is running on the cluster. We have to ask for an exemption every time we want to delay patching a machine for a long running production job. Basically, while our group is responsible for the machines we have little control over IT's patch schedule. Is patching monthly with MS's schedule sane for a production Windows cluster? Are there software hooks in WSUS where we could say, "please don't reboot just yet"?

  Read the article

• Why cache static files with Varnish, why not pass

  - by Saif Bechan

  I have a system runnning nginx / php-fpm / varnish / wordpress and amazon s3. Now I have looked at a lot of configuration files while setting up the system, and in all of them I found something like this: /* If the request is for pictures, javascript, css, etc */ if (req.url ~ "\.(jpg|jpeg|png|gif|css|js)$") { /* Remove the cookie and make the request static */ unset req.http.cookie; return (lookup); } I do not understand why this is done. Most of the examples also run NginX as a webserver. Now the question is, why would you use the varnish cache to cache these static files. It makes much more sense to me to only cache the dynamic files so that php-fpm / mysql don't get hit that much. Am I correct or am I missing something here? UPDATE I want to add some info to the question based on the answer given. If you have a dynamic website, where the content actually changes a lot, chaching does not make sense. But if you use WordPress for a static website for example, this can be cached for long periods of time. That said, more important to me is static conent. I have found a link with some test and benchmarks on different cache apps and webserver apps. http://nbonvin.wordpress.com/2011/03/14/apache-vs-nginx-vs-varnish-vs-gwan/ NginX is actually faster in getting your static content, so it makes more sense to just let it pass. NginX works great with static files. -- Apart from that, most of the time static content is not even in the webserver itself. Most of the time this content is stores on a CDN somewhere, maybe AWS S3, something like that. I think the varnish cache is the last place where you want to have you static content stored.

  Read the article

• How best to manage my growing data in Excel?

  - by Mike

  This isn't a question about formulas or features in Excel. I'm debating the correct/best way to manage the growing amount of data 'I have to' manage in Excel (I produce PIVOT tables/reports for my management). DATA: I record the number of publications we order: cost, date ordered, start and end of subscription, who requested it, when they ordered it, when I ordered it, will it be cancelled next year, etc, etc, etc. DILEMMA: Obviously we re-order a lot of the same publications, so depending on how I manage the data I could be duplicating all over the place. OPTION 1: So, do I use ROWs = publication name in Row 1 and all the related columns for each financial year are copied and pasted after each financial year ready for the new FY information? This will lead to me going to column ZZ. OPTION 2: Or, do I use COLUMNs = each row has only one FY information for each publication and if we re-order or cancel a publication I re-type the publication name in a row below and fill in appropriate columns? This will lead to a long list of publications down to row 10000, and potential for misspelling of repeat ordered publication names. IDEAS: What's the best way - thinking in terms of pivot table best practice, being able to sum or count easy, report formatting, etc. Any best practices much appreciated.

  Read the article

• Moving server room to another part of the building

  - by PHLiGHT

  This question is a bit different than the typical we are moving our server room to an off site location or we are moving the whole office to a new building. Management wants to add some more office space and to do so they want to move the server room to another location. The server room has Verizon smart jacks, a few servers, PBX and all the office network drops go into this room. I'm going to go over there to scout out an alternate location for the equipment because that is still TBD. This sounds like quite a pain since the Verizon equipment for our MPLS will need to be moved (never done that) and the office jacks will need to be re-run. How do you handle the jacks? I was thinking of keeping them in the same location and having new wall plates put in with half the ports going to the current location and the other half to the new location. Or do you think that 40 drops could just be done over the weekend so the old stuff would be ripped out and replaced with the new? Currently the wiring is a mess so this could be a blessing in the long run.

  Read the article

• CentOS 6.3 Virtual under OpenVZ cannot ping, host lookups, outbound connections while postfix running

  - by Paul Cravey

  My best theory is that some kernel limit is being hit preventing outbound connections. We have tried basically everything from tcpdumps to provisioning an entirely new virtual server (we do not have this problem on any other virtuals), however the problem somehow carried over, even with new postfix build (working). Emails work, and outbound connections work, so long as postfix does not have too much going on. /proc/user_beancounters shows no limits being hit (show below). Nevertheless, pings fail even to IP addresses. TCP stack appears healthy. Load is low. No iowait. Flushed iptables already. Has anyone experienced anything like this? uid resource held maxheld barrier limit failcnt 3: kmemsize 166216365 170262528 9223372036854775807 9223372036854775807 0 lockedpages 0 0 9223372036854775807 9223372036854775807 0 privvmpages 285727 351885 9223372036854775807 9223372036854775807 0 shmpages 16933 17605 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 numproc 150 303 9223372036854775807 9223372036854775807 0 physpages 314156 326191 0 1280000 0 vmguarpages 0 0 9223372036854775807 9223372036854775807 0 oomguarpages 165355 165355 9223372036854775807 9223372036854775807 0 numtcpsock 89 172 9223372036854775807 9223372036854775807 0 numflock 22 76 9223372036854775807 9223372036854775807 0 numpty 1 2 9223372036854775807 9223372036854775807 0 numsiginfo 0 75 9223372036854775807 9223372036854775807 0 tcpsndbuf 2733472 4371752 9223372036854775807 9223372036854775807 0 tcprcvbuf 1798336 5427296 9223372036854775807 9223372036854775807 0 othersockbuf 491120 1000760 9223372036854775807 9223372036854775807 0 dgramrcvbuf 0 238728 9223372036854775807 9223372036854775807 0 numothersock 361 505 9223372036854775807 9223372036854775807 0 dcachesize 135941831 136114679 9223372036854775807 9223372036854775807 0 numfile 2905 4990 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 8 9 9223372036854775807 9223372036854775807 0 [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. --- 4.2.2.1 ping statistics --- 9 packets transmitted, 0 received, 100% packet loss, time 8493ms [root@bni /]# service postfix stop [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. 64 bytes from 4.2.2.1: icmp_seq=1 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=2 ttl=53 time=8.62 ms 64 bytes from 4.2.2.1: icmp_seq=3 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=4 ttl=53 time=8.66 ms Outbound connections of all sorts fail when postfix is running.

  Read the article

• Sudden and frequent hangs on desktop computer: mobo or CPU fault?

  - by djechelon

  I have a desktop computer equipped with an ASUS Crosshair 2 Formula and a Phenom x6 3.2GHz CPU. My problem is that often the computer will hang all of a sudden, completely stopping responding. When that occurs, reset key is inoperative and power button turns the computer off but is unable to turn it back on. I have to physically disconnect power cable. The problem can occur anytime, when I'm booting Windows, when I'm logging in, when I'm listening to a song, when I'm browsing Internet, etc. It always occurs after very few minutes of 3D gameplay I thought it was a video card fault. I had 3 8800GTX so I could try all combinations of them: didn't fix I thought it was a RAM problem: I tried running with only a subset of my DDR2 banks but didn't fix. Almost every time I have to reset and reconfigure BIOS (without AHCI, Win7 won't boot, so I need to restore a few things). If I enable AMD Live, Cool&Quiet or other things from CPU configuration menu I'll be sure that the computer won't reach Windows desktop in 99% of cases (it randomly hangs somewhere in the boot process or even in the BIOS POST). Another interesting thing is that during the POST process the computer always takes unusually long time detecting USB devices (LCD POSTer shows USB INIT), and I've also tried disconnecting all USB devices but didn't take less time to POST BIOS revision is 2702, the latest. Today I found a different behaviour once: during boot screen I got a BSOD with error Stop 0x00000101 A clock interrupt was not received on a secondary processor within the allocated time interval, and this is usually related to overclocking, but I never overclocked my CPU. Judging from the description of my problem, hoping someone had the same and fixed, and since I don't have a spare CPU or motherboard for replacement, I'd like to ask if you think this is a problem with faulty CPU or faulty motherboard, and if I can perform additional tests (I mean software tests because of my lack of spare components) to identify the component to replace.

  Read the article

• Reliable custom Windows shortcut keys?

  - by Peter Baer

  I have global Windows shortcut keys assigned to several different cmd.exe instances. I do this by creating shortcuts to cmd.exe on my desktop, and assigning each one a unique shortcut key (for example, CTRL + SHIFT + U). Pretty basic stuff. I'm using Win2K8 (R1 and R2). This works just fine... most of the time. But with infuriating regularity, sometimes it doesn't. Or it will work with a long delay (many seconds). It doesn't matter what app currently has focus (it can even be one of the command prompts). It doesn't matter what keys I assign (I've tried a few variations of WIN, CTRL and SHIFT). I did notice that this is often, but not always, correlated with explorer.exe struggling in some way or another (say, an explorer window opened to a file share that's unavailable, or an app being unresponsive, or whatever). In other words the shortcut key handling appears to be very sensitive to unrelated system activity. Note that whenever I have this problem I can always successfully ALT + TAB to the window I want to get to, but that's tedious. I use the shortcuts to these command windows hundreds of times a day so even a 1% failure rate becomes really annoying. Is there a way to fix this, or is there some third-party utility out there that will RELIABLY intercept custom key combinations to bring focus to whatever apps I want, in a way that is independent of other system activity? ADDENDUM: There is a property of the Windows shortcuts that I would not want to lose if switching to a third-party hotkey tool: Windows shortcuts are idempotent. Once you've launched a shortcut to some app, pressing the shortcut key combo again takes you to the already launched process - it does not launch a new process.

  Read the article

< Previous Page | 529 530 531 532 533 534 535 536 537 538 539 540  | Next Page >