Search Results

Search found 3994 results on 160 pages for 'dual wan'.

Page 54/160 | < Previous Page | 50 51 52 53 54 55 56 57 58 59 60 61  | Next Page >

  • Cisco 851 (IOS) router: FastEthernet 4 (WAN) got the shutdown flag.

    - by cjavapro
    At a customer location there was a Cisco 851 router (which uses IOS). The PCs on location were all of a sudden unable to connect. We came on site and found that FastEthernet 4 (the WAN port) was "administratively down". We ran these commands to resolve it config t interface fa4 no shutdown exit exit write Now the mystery is how the shutdown flag got there in the first place? The router was on battery backup... but during the outage it was power cycled by the customer. It is possible that there was a short outage by the ISP and that the power cycle caused the shutdown flag to come up. There may have been a hack or an attack pattern that caused the shutdown flag to come up. There may have been a hack or an attack pattern that the router to become unavailable and then caused the shutdown flag to be added on startup. Question: Does anybody have any clues? or at least remember that they had a shutdown flag come up on their WAN port also?

    Read the article

  • Multiple Routers, Failover, DHCP and multiple gateways. NOT WAN-failover

    - by u_b
    I've had a look around google and this forum but could not find an answer to my question. So probably one of you can help me a little. My intended setup is: Router R1: wan connection to isp. connected backup server. provides some wireless SSID. other connected devices like printer, laptop, etc. both wired and wireless. Router R2: no wan connection to isp but connected to R2. connects mp3-streamer and music server. also serves as a wireless access point with same SSID. other than described connections only wireless connections. I would like to be able to control music even if R1 is off, e.g. with no internet connection. On the other hand I would like to access internet also in the case that R2 is off, i.e. no music access. Last but not least I would like to stream internet radio, i.e., R1 and R2 are on, and music is streamed from internet to R1 to R2 to streamer. I would like to realize all this using DHCP (also using static assignments) so i do not have to configure statically on android, laptop, etc. So my questions are: Can I make DHCP provide a list of two default gateways R1,R2? In order to make clients fallback to other gateway if currently assigned gateway is turned off? Thanks in advance, u_b

    Read the article

  • How to install Windows 8 to dual boot with Windows 7/XP?

    - by Gopinath
    Microsoft released Windows 8 beta(customer preview) few days ago and yesterday I had a chance to install it on one of my home computers. My home PC is running on Windows 7 and I would like to install Windows 8 side by side so that I can dual boot. The installation process was pretty simple and with in 40 minutes my PC was up and running with beautiful Windows 8 OS along with Windows 7. In this post I want to share my experience and provide information for you to install Windows 8. 1. Identify a drive  with at least 20 GB of space – Identify one of the drives on your hard disk that can be used to install Windows 8. Delete all the files or preferably quick format it and make sure that it has at least 20 GB of free space. Rename the drive name to Windows 8 so that it will be helpful to identify the destination drive during installation process. 2. Download Windows 8 installer ISO– Go to Microsoft’s website and download Windows 8 ISO file which is approximately 2.5 GB file(32 bit English version). 3. Create Windows 8 bootable USB/DVD – Its advised to launch Windows 8 installer using a bootable USB or DVD for enabling dual boot instead of unzipping the ISO file and launching the setup from Windows 7 OS. Also consider creating bootable USB instead of bootable DVD to save a disc. To create bootable USB/DVD follow these steps Download and install the Windows 7 DVD / USB tool available at microsoftstore.com Launch the utility and follow the onscreen instructions where you would be asked to choose the ISO file(point to file downloaded in step 2) and choose a USB drive or DVD as destination. The onscreen instructions are very simple and you would be able to complete it in 20 minutes time. So now you have Windows 8 installation setup on your USB drive or DVD. 4. Change BIOS settings to boot from USB/DVD – Restart your PC and open BIOS configuration settings key by pressing F2 or  F12 or DELETE key (the key depends on your computer manufacturer). Go to boot sequence options and make sure that USB/DVD is ahead of hard disk in the boot sequence. Save the settings and restart the PC. 5. Install Windows 8 – After the restart you should be straight into Windows 8 installation screen. Follow the onscreen instructions and install Windows 8 on the drive that is identified during step 1. When prompted for product serial key enter NF32V-Q9P3W-7DR7Y-JGWRW-JFCK8. The installer would restart couple of times during the installation process. On the first restart, make sure that you remove USB/DVD. Windows 8 installation process is pretty simple and very quick. The complete process of creating bootable USB and installation should complete in 30 – 40 minutes time.

    Read the article

  • Microsoft souhaiterait vendre 100 millions de Windows Phone en 2012, les raisons de la non-prise en charge du dual-core par l'OS divulguées

    Microsoft a pour objectif de vendre 100 millions de Windows Phone en 2012 Les raisons de la non-prise en charge des processeurs dual-core par l'OS divulguées Microsoft aurait pour objectif interne de commercialiser plus de 100 millions de terminaux Windows Phone en 2012 d'après WMPowerUser, d'une source non divulguée. L'éditeur pourrait atteindre cet objectif ambitieux, si le constructeur Nokia amplifie sa production de terminaux Windows Phone à travers le monde avec des modèles différents. Selon WMPowerUser, les opérateurs s'attendraient à voir Windows Phone prendre 30% de parts de marché de smartphones en 2012. Une estimation qui rejoint celle

    Read the article

  • Is it possible to dual boot Mac OSX Lion with Ubuntu 12.04?

    - by tofu_bacon
    I've read that it can be dangerous for your computer to try to run Ubuntu and that the safest option is to run it on an external hard drive. Is this true? (I don't want to run it through a Virtual Machine.) I would prefer to dual boot it, given that my hard drive has so much space. Update: So does this mean that even if I have Ubuntu installed, that my data would still be at risk due to, say, stability issues?

    Read the article

  • MIT vs. BSD vs. Dual License

    - by ryanve
    My understanding is that: MIT-licensed projects can be used/redistributed in BSD-licensed projects. BSD-licensed projects can be used/redistributed in MIT-licensed projects. The MIT and the BSD 2-clause licenses are essentially identical. BSD 3-clause = BSD 2-clause + the "no endorsement" clause Issuing a dual license allows users to choose from those licenses—not be bound to both. If all of the above is correct, then what is the point of using a dual MIT/BSD license? Even if the BSD refers to the 3-clause version, then can't a user legally choose to only abide by the MIT license? It seems that if you really want the "no endorsement" clause to apply then you have to license it as just BSD (not dual). If you don't care about the "no endorsement" clause, then MIT alone is sufficient and MIT/BSD is redundant. Similarly, since the MIT and BSD licenses are both "GPL-compatible" and can be redistributed in GPL-licensed projects, then dual licensing MIT/GPL also seems redundant.

    Read the article

  • Licencing: release the same software with double licence

    - by Luca
    In my free time, I develop (alone, sigh) a project, in particoular an application library. I've released it using GPL v3. At this time, this project has come very useful for a job. I'd like to release my OSS library toghether with the application using the same GPL v3 licence, with the exception that it can be linked for the specific application, or for the specific application vendor. AFAIK, the copyright owner can handle the entire source and licencing it, I did it; and probably the licence owner could cut&paste its own code, change its licence and use for other projects, isn't? But an GPL'ed library cannot be linked with a proprietary software, right? But software could be double-licenced, as MySQL does. So the question is: what should I do to allow the distribution of my GPL'ed library with a proprietary software, being the copyright owner?

    Read the article

  • C# winform Show form in second screen and vice versa

    - by Mohsan
    hi. I have an application in which there is a form which i wants to show on second screen. Mean If application is running on screen A and when i click on menu to show Form it should display on Screen B and same with if application is running on screen B and when i click on menu to show Form it should display on Screen A. please tell me how to do that. If you provide code then it will be better. i searched from net and found some articles to get primary and secondary screens. but unable to implement that.

    Read the article

  • Move application to second monitor in MFC

    - by Anu
    Hi, I m developing applcaiton in VS2008 VC++.net I want to move the application to secondary monitor.Not by clicking and dragging using mouse. Is there any function like MoveToMonitor by pressing the button or any shortcut keys. Then it should move to secondary monitor.

    Read the article

  • Two windows fullscreen on two different screen.

    - by sirithang
    Hi! I'm actually working on an app to display an image onto a Dome. The dome projection system is constitued of two projector and a pc running a GentoO Linux and KDE, with nvidia TwinView system. Since here i've used SDL to display a fullscreen windows, and it display my app onto the two screen. But i just figured that i need to project two different images, one on each projector. That's why i search for a solution to display a fullscreen window on the first screen (projector) and another on the second. But SDL fullscreen just extend the window to the two screens. I can use any librairie (since it light and free, as i will wrap it into my small "API"), or change display setting. BTW it would be nice to have openGL support, since SDL manage only one window ^^"

    Read the article

  • [C++]Two windows fullscreen on two different screen.

    - by sirithang
    Hi! I'm actually working on an app to display an image onto a Dome. The dome projection system is constitued of two projector and a pc running a GentoO Linux and KDE, with nvidia TwinView system. Since here i've used SDL to display a fullscreen windows, and it display my app onto the two screen. But i just figured that i need to project two different images, one on each projector. That's why i search for a solution to display a fullscreen window on the first screen (projector) and another on the second. But SDL fullscreen just extend the window to the two screens. I can use any librairie (since it light and free, as i will wrap it into my small "API"), or change display setting. BTW it would be nice to have openGL support, since SDL manage only one window ^^"

    Read the article

  • timing control for parallel processes

    - by omrihsan
    how can i control two processes to run alternately in separate terminal windows. for example i run the code for each on separate terminal windows at 11:59 and both of them wait for the time to be 12:00. at this moment process one starts execution and process two waits for say 10 seconds. then they switch, process two executes and process one waits. in this way they take turns until the process is complete.

    Read the article

  • How to use Public IP in case of two ISP when two differs from each other

    - by user1471995
    Please bare with my long explanation but this is important to explain the actual problem. Please also pardon my knowledge with PFsense as i am new to this. I have single PFSense box with 3 Ethernet adapter. Before moving to configuration for these, i want to let you know i have two Ethernet based Internet Leased Line Connectivity let's call them ISP A and ISP B. Then last inetrface is LAN which is connected to network switch. Typical network diagram ISP A ----- PFSense ----> Switch ---- > Servers ISP B ----- ISP A (Initially Purchased) WAN IP:- 113.193.X.X /29 Gateway IP :- 113.193.X.A and other 4 usable public IP in same subnet(So the gateway for those IP are also same). ISP B (Recently Purchased) WAN IP:- 115.115.X.X /30 Gateway IP :- 115.115.X.B and other 5 usable public IP in different subnet(So the gateway for those IP is different), for example if 115.119.X.X2 is one of the IP from that list then the gateway for this IP is 115.119.X.X1. Configuration for 3 Interfaces Interface : WAN Network Port : nfe0 Type : Static IP Address : 113.193.X.X /29 Gateway : 113.193.X.A Interface : LAN Network Port : vr0 Type : Static IP Address : 192.168.1.1 /24 Gateway : None Interface : RELWAN Network Port : rl0 Type : Static IP Address : 115.115.X.X /30 (I am not sure of the subnet) Gateway : 115.115.X.B To use Public IP from ISP A i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- WAN TCP/UDP * * 113.193.X.X1 53 (DNS) 192.168.1.5 53 (DNS) WAN TCP/UDP * * 113.193.X.X1 80 (HTTP) 192.168.1.5 80 (HTTP) WAN TCP * * 113.193.X.X2 80 (HTTP) 192.168.1.7 80 (HTTP) etc., c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the WAN those are only present. d) If this section in relevant then for Firewall: Rules at WAN tab then following default rule has been generated. * RFC 1918 networks * * * * * Block private networks * Reserved/not assigned by IANA * * * * * * To use Public IP from ISP B i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- RELWAN TCP/UDP * * 115.119.116.X.X1 80 (HTTP) 192.168.1.11 80 (HTTP) c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the RELWAN those are only present. d) If this section in relevant then for Firewall: Rules at RELWAN tab then following default rule has been generated. * RFC 1918 networks * * * * * * Reserved/not assigned by IANA * * * * * * Last thing before my actual query is to make you aware that to have multiple Wan setup i have done following steps a) Under System: Gateways at Groups Tab i have created new group as following MultipleGateway WANGW, RELWAN Tier 2,Tier 1 Multiple Gateway Test b) Then Under Firewall: Rules at LAN tab i have created a rule for internal traffic as follows * LAN net * * * MultipleGateway none c) This setup works if unplug first ISP traffic start routing using ISP 2 and vice-versa. Now my main query and problem is i am not able to use public IP address allocated by ISP B, i have tried many small tweaks but not successful in anyone. The notable difference between the two ISP is a) In case of ISP A there Public usable IP address are on same subnet so the gateway used for the WAN ip is same for the other public IP address. b) In case of ISP B there public usable IP address are on different subnet so the obvious the gateway IP for them is different from WAN gateway's IP. Please let me know how to use ISP B public usable IP address, in future also i am going to rely for more IPs from ISP B only.

    Read the article

  • Is real-time or synchronous replication possible over WAN link?

    - by johnnyb10
    The company I work for is looking to implement truly real-time file replication with file locking over a WAN link that spans over 2000 miles. We currently have a 16-drive SAN setup in our east coast office. We also have an office out in Colorado that will have the same exact SAN setup. The idea is to have those two SANs contain the same exact data at all times, which will allow us to work with the same data pool, and which will also provide use with an offsite backup solution, should a failure occur on either end. We're running Server 2008. The objective is to enable users in the east coast office to work on files and have those changes be instantly updated on the Colorado SAN as well. We also need there to be file locking so that there will be no conflicts or overwritten changes if users attempt to work on the same file. Is this scenario even possible, at speeds that would make the files usable? And if so, what software would we need to pull this off? As I understand it, DFS-R does not provide file locking, so if we used that, we would need to go with a third-party product like Peerlock. But I don't even know if DFS-R is an option. Can it replicate quickly enough over a WAN link? Can any product? It seems that if we were to use synchronous replication, the programs would be unacceptably slow, as every write would have to wait for confirmation from the other end of the link. But if we used asynchronous replication, what kind of latency would we be looking at? There is a product from GlobalScape called WAFS that claims to provide "File coherence with real-time file locking, file release, and synchronization" and says that "As files are modified, changes are mirrored instantly using intelligent byte-level differencing to minimize the impact on network bandwidth". So this sounds like synchronous replication, but that doesn't even seem possible, given physical limitations such as the speed of light. If anyone has any experience with this kind of setup, or knows whether it's even possible, I'd appreciate your input and suggestions, including recommendations for software that we should check out.

    Read the article

  • Impact of the L3 cache on performance - worth a dual-processor system?

    - by Dan Nissenbaum
    I will be purchasing a new high-end system, and I would like to have a better sense of whether a dual-processor Xeon system (I am looking at the new, high-end Xeon E5-2687W) might, realistically, provide a noticeable performance improvement due to the doubling of the L3 cache (20 MB per CPU). (This is in addition to the occasional added advantage due to the doubling of cores and RAM.) My usage scenario is, roughly, that I have many background applications running at any time - 3 or 4 data compression/backup applications, a low-impact web server, one or two virtual machines at any given time (usually fairly idle), and perhaps 20 utility programs that utilize a noticeable (but small) portion of the CPU cores. In total, when I am not actively using the computer, about 25% of the total CPU power is utilized in my current i7-970 6-core (12 thread) system. When I am doing routine work, the CPU utilization often exceeds 50%, and occasionally hits 75%-80%. The Xeon E5-2687W is not only a second-generation i7 (so should improve performance for that reason), but also has 8 cores (16 threads), rather than 6 cores. For this reason, I expect to run into the 75% CPU range even less frequently. Nonetheless, the ability to double the cores and the RAM is a consideration. However, in the end, I believe this decision comes down to whether the doubling of the L3 cache will provide a noticeable improvement. There are many benchmarks, and a lot of discussion, regarding CPU power. However, I find very little discussion of L3 cache utilization, and how increases in the L3 cache (such as doubling it with dual processors) affect performance. For example: If there are only two processes running, but each benefits from a large L3 cache (such as might be the case for background processes that frequently scan the file system), perhaps the overall system performance might noticeably improve with dual CPU's - even if only a single core is active on each CPU - due to each process having double the effective L3 cache. I am hoping that someone has a sense of the benefits of increasing (or doubling) the L3 cache size. Note: the CPU I am considering (the Xeon E5-2687W) has 20 MB L3 cache, so a system with dual CPU's would have 40 MB L3 cache.

    Read the article

  • How can a single threaded application like Excel 2003 take more than 50% of a hyper-threaded or dual

    - by Lunatik
    I'm waiting for Excel to finish a recalculation and I notice that the CPU usage as reported by Task Manager occasionally spikes to 51% or 52% on a Pentium 4 with hyper-threading. How is a single-threaded application like Excel 2003 doing this? Is it just a rounding/estimation error on the part of Task Manager? Or is it something to do with HT allocation i.e. I wouldn't see this happening on a genuine dual-core or dual-CPU machine?

    Read the article

  • ATG Live Webcast March 21 Reminder: Network, WAN, and PC Performance Tuning (Performance Series Part 3 of 3)

    - by BillSawyer
    A quick reminder about tomorrow's webcast:  Andy Tremayne, Senior Architect, Applications Performance, and co-author of Oracle Applications Performance Tuning Handbook from Oracle Press, and Uday Moogala, Senior Principal Engineer, Applications Performance, will discuss network performance for E-Business Suite. Andy and Uday will cover tuning the client and tuning the network. They will share real-life examples of network performance, and show you tools and techniques that you can use to estimate or simulate performance on your own network.The agenda for the Performance Tuning - Part 3 of 3 webcast includes the following topics: Tuning the Client Tuning the Network Date:               Thursday, March 21, 2012Time:              8:00 AM - 9:00 AM Pacific Standard TimePresenters:  Andy Tremayne, Senior Architect, Applications Performance                        Uday Moogala, Senior Principal Engineer, Applications PerformanceWebcast Registration Link (Preregistration is optional but encouraged)To hear the audio feed:   Domestic Participant Dial-In Number:           877-697-8128    International Participant Dial-In Number:      706-634-9568    Additional International Dial-In Numbers Link:    Dial-In Passcode:                                              99341To see the presentation:    The Direct Access Web Conference details are:    Website URL: https://ouweb.webex.com    Meeting Number:  591264961If you miss the webcast, or you have missed any webcast, don't worry -- we'll post links to the recording as soon as it's available from Oracle University.  You can monitor this blog for pointers to the replay. And, you can find our archive of our past webcasts and training here.

    Read the article

  • Tutorial (or livedisk) for multiseat setup with dual-head display supporting openGL direct rendering?

    - by Tobias Kienzler
    I'm currently running Ubuntu 10.10 (64 bit), the GPU is an ATI Radeon HD 4290 onboard a ASUS M4A89GTD PRO/USB3 mainboard. The Ubuntu wiki doesn't cover 10.10 yet and I also don't know if that method would support direct rendering. I heard mentions of xephyr and xgl, what are the differences? Where should I start? I tried the mdm livedisk but that doesn't boot. I'm also willing to try a different distribution if necessary. Edit: 1 Will the HowTo: A well performing, full eye-candy, accelerated pseudo-multiseat setup on a single dualhead GPU. for Ubuntu 9.04 still work? I'm afraid it omits how to setup two input devices and sound however... Edit: 2 http://multiseatonlinux.blogspot.com/2010/06/part-1-setting-up-base.html covers 10.10 but requires pinning gdm. Is that circumvenatable? Also how does that setup have to be modified for dual-head?

    Read the article

  • How do I get my ART USB Dual Pre preamp to work?

    - by Zach
    I am using Audacity. I have an ART USB Dual Pre preamp. Ubuntu is not recognizing it whatsoever. I am able to record in Audacity, but it is using the mic that is built into my computer (which is a compaq Presario CQ50) instead of the one plugged into the preamp. How do I get Ubuntu to recognize the preamp that is plugged into my computer? Something tells me it has to do with the installation of the preamp software. It came with a installation CD, but when I go to "install", the nothing happens. I can view what is on the CD, but there is no installing of anything. Please help!

    Read the article

  • Dual Monitor/Xinerama not working; cannot even detect on-board graphic card

    - by Steven H
    I have Kubuntu 12.04 and two identical VGA monitors. One I plugged via DVI-VGA adapter into the DVI port of my discrete AMD Radeon HD 6670, the other into the VGA port of my on-board graphic card (Radeon HD 6410D). After installing Kubuntu I got a black screen, so I booted with nomodeset and installed AMD's catalyst drivers but only the monitor plugged into the discrete graphic card worked. Using lspci I saw that the on-board graphics was not listed. Then I found in the BIOS settings the options "Surround View" and "Onboard Dual Link DVI" both disabled. After enabling both, the on-board graphics card shows up in lspci but in amdcccle, it only shows as [Uknown display]Uknown adapter. When I try to enable xinerama, I get a black screen after rebooting on both monitors. I tried several options and hints from the web but nothing worked so far. I also reinstalled the AMD drivers several times. What should I do?

    Read the article

  • Dual Boot 10.10 and 11.04 can't boot into 10.10 after an update.

    - by Gaurav Butola
    I've been dual booting my system with Ubuntu 10.10 (Maverick Meerkat) and 11.04 (Natty Narwhal) but today after an update, I can't boot into 10.10, there's only option to boot into 11.04 and Grub also looks a bit different. Before this update, I used to see first option for 11.04 and an other option called /dev/sda1 for 10.10 but now there is a new option called Previous Linux Versions, but when I Enter into that menu, there is no option to boot into 10.10 all the options take me to 11.04 now it looks like this... And when I click on Previous Linux Versions...

    Read the article

  • T-SQL Tuesday #34: Help me, Obi-Wan Kenobi, You're My Only Hope!

    - by AllenMWhite
    This T-SQL Tuesday is about a person that helped you understand SQL Server. It's not a stretch to say that it's people that help you get to where you are in life, and Rob Volk ( @sql_r ) is sponsoring this month's T-SQL Tuesday asking who is that person that helped you get there. Over the years, there've been a number of people who've helped me, but one person stands out above the rest, who was patient, kind and always explained the details in a way that just made sense. I first met Don Vilen at...(read more)

    Read the article

< Previous Page | 50 51 52 53 54 55 56 57 58 59 60 61  | Next Page >