Search Results

Search found 17595 results on 704 pages for 'log'.

Page 543/704 | < Previous Page | 539 540 541 542 543 544 545 546 547 548 549 550  | Next Page >

  • Network corruption - corrupt downloads, corrupt streams, etc.

    - by rfrankel
    I've been having some problems with my home LAN. Downloaded executables won't run, my remote desktop sessions keep getting interrupted due to encryption errors, flash video streams show visible corruption (both Hulu and YouTube), and I've had a couple downloads for which the md5 hashes don't match. The problem has even occurred with a couple images embedded in webpages, though that's rare enough (presumably because images are relatively smaller files). I've had this problem across two Windows machines and a Mac, so it's neither machine-specific nor at the app or OS level. Comcast claims it's nothing to do with them, and my Linksys/Cisco RV016 router is out of warranty, so I have no access to official support. When I log into my router, it shows no error packets or dropped packets received. I plugged a laptop directly into the router and was able to download a 5.5 MB file and verify its MD5 hash, which is not proof that the problem is downstream of the router, but makes it seem quite likely, since I failed to download the same file several times from two desktops (one Mac, one Windows). Could this be a wiring problem? If so, is there any way clever/elegant to determine which wiring is faulty with just software? If I can avoid tracing all the wires throughout my entire house it would make my life quite a bit easier.

    Read the article

  • Can't get SSH public key authentication to work

    - by Trey Parkman
    My server is running CentOS 5.3. I'm on a Mac running Leopard. I don't know which is responsible for this: I can log on to my server just fine via password authentication. I've gone through all of the steps for setting up PKA (as described at http://www.centos.org/docs/5/html/Deployment_Guide-en-US/s1-ssh-beyondshell.html), but when I use SSH, it refuses to even attempt publickey verification. Using the command ssh -vvv user@host (where -vvv cranks up verbosity to the maximum level) I get the following relevant output: debug2: key: /Users/me/.ssh/id_dsa (0x123456) debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug3: start over, passed a different list publickey,gssapi-with-mic,password debug3: preferred keyboard-interactive,password debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password followed by a prompt for my password. If I try to force the issue with ssh -vvv -o PreferredAuthentications=publickey user@host I get debug2: key: /Users/me/.ssh/id_dsa (0x123456) debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug3: start over, passed a different list publickey,gssapi-with-mic,password debug3: preferred publickey debug3: authmethod_lookup publickey debug3: No more authentication methods to try. So, even though the server says it accepts the publickey authentication method, and my SSH client insists on it, I'm rebutted. (Note the conspicuous absence of an "Offering public key:" line above.) Any suggestions?

    Read the article

  • SQL Server Express Failed to Install

    - by JasCav
    I am attempting to install SQL Server Express (as part of the Visual Studio 2010 Professional installation), but it is failing. I am receiving this error log. [06/22/11,16:31:39] Microsoft Visual Studio 2010 Professional - ENU: [2] UpdateFileFetcherFromMsi: Warning: Missing fwlink entry for cabinet: #SP.cab [06/22/11,16:31:40] setup.exe: [2] Duplicate module ID: {0AFE11CA-57AA-4F66-90BE-284F0F3A5ABD} [06/22/11,16:32:12] setup.exe: [2] Duplicate component in install order: SQL EULAs [06/22/11,16:32:12] setup.exe: [2] Duplicate component in install order: SQL EULAs [06/22/11,16:32:12] setup.exe: [2] Duplicate component in install order: SQL EULAs [06/22/11,17:07:55] Microsoft Visual Studio 2010 Professional - ENU: [2] UpdateFileFetcherFromMsi: Warning: Missing fwlink entry for cabinet: #SP.cab [06/22/11,17:07:55] setup.exe: [2] Duplicate module ID: {0AFE11CA-57AA-4F66-90BE-284F0F3A5ABD} [06/23/11,10:39:33] Microsoft Visual Studio 2010 Professional - ENU: [2] UpdateFileFetcherFromMsi: Warning: Missing fwlink entry for cabinet: #SP.cab [06/23/11,10:39:33] setup.exe: [2] Duplicate module ID: {0AFE11CA-57AA-4F66-90BE-284F0F3A5ABD} [06/23/11,10:40:22] setup.exe: [2] Duplicate component in install order: SQL EULAs [06/23/11,10:40:22] setup.exe: [2] Duplicate component in install order: SQL EULAs [06/23/11,10:40:22] setup.exe: [2] Duplicate component in install order: SQL EULAs [06/23/11,10:53:48] Microsoft Visual Studio 2010 Professional - ENU: [2] UpdateFileFetcherFromMsi: Warning: Missing fwlink entry for cabinet: #SP.cab [06/23/11,10:53:48] setup.exe: [2] Duplicate module ID: {0AFE11CA-57AA-4F66-90BE-284F0F3A5ABD} [06/23/11,13:19:26] Microsoft Visual Studio 2010 Professional - ENU: [2] UpdateFileFetcherFromMsi: Warning: Missing fwlink entry for cabinet: #SP.cab [06/23/11,13:19:26] setup.exe: [2] Duplicate module ID: {0AFE11CA-57AA-4F66-90BE-284F0F3A5ABD} [06/23/11,16:47:36] Microsoft SQL Server 2008 Express Service Pack 1 (x64): [2] Error code -2068643839 for this component is not recognized. [06/23/11,16:47:36] Microsoft SQL Server 2008 Express Service Pack 1 (x64): [2] Component Microsoft SQL Server 2008 Express Service Pack 1 (x64) returned an unexpected value. ***EndOfSession*** I'm reading various articles which point towards something being wrong in the register, but I can't find anything specific. Any suggestions for what I can do to fix this?

    Read the article

  • How do I easily repair a single unreadable block on a Linux disk?

    - by Nelson
    My Linux system has started throwing SMART errors in the syslog. I tracked it down and believe the problem is a single block on the disk. How do I go about easily getting the disk to reallocate that one block? I'd like to know what file got destroyed in the process. (I'm aware that if one block fails on a disk others are likely to follow; I have a good ongoing backup and just want to try to keep this disk working.) Searching the web leads to the Bad block HOWTO, which describes a manual process on an unmounted disk. It seems complicated and error-prone. Is there a tool to automate this process in Linux? My only other option is the manufacturer's diagnostic tool, but I presume that'll clobber the bad block without any reporting on what got destroyed. Worst case, it might be filesystem metadata. The disk in question is the primary system partition. Using ext3fs and LVM. Here's the error log from syslog and the relevant bit from smartctl. smartd[5226]: Device: /dev/hda, 1 Currently unreadable (pending) sectors Error 1 occurred at disk power-on lifetime: 17449 hours (727 days + 1 hours) ... Error: UNC at LBA = 0x00d39eee = 13868782 There's a full smartctl dump on pastebin.

    Read the article

  • Apache2 refuses to process php files - "Snow Leopard" OSX 10.6.4

    - by w-01
    I have a macbook pro i5. my understanding is that by default it should be able to serve php5. i have uncommented the relevant line in /etc/apache2/httpd.conf LoadModule php5_module libexec/apache2/libphp5.so I have restarted apache with sudo apachectl -k restart and when i try to access a file with a php extension, Apache prompts me to download the file. i.e. instead of processing the php and sending me html, it thinks i want to download the file.... when i look in apache error log i see this [Fri Nov 12 10:16:14 2010] [notice] Apache/2.2.14 (Unix) PHP/5.3.2 mod_ssl/2.2.14 OpenSSL/0.9.8l DAV/2 mod_wsgi/3.2 Python/2.6.1 configured -- resuming normal operations so it looks like php5 is loading properly. I'd like to know either: How do i fix this? or How do I reinstall apache2 so that it's like i just installed the os? thanks in advance update @Zayne - the end of my httpd.conf has Include /private/etc/apache2/other/*.conf and i have a file /etc/apache2/other/php.conf with the contents <IfModule php5_module> AddType application/x-httpd-php .php AddType application/x-httpd-php-source .phps <IfModule dir_module> DirectoryIndex index.html index.php </IfModule> </IfModule> @Zayne I've already copied php.ini.default to php.ini in the same folder. when i run sudo apachectl configtest i get /usr/sbin/apachectl: line 82: ulimit: open files: cannot modify limit: Invalid argument httpd: Could not reliably determine the server's fully qualified domain name, using ::1 for ServerName Syntax OK furthermore i decided to try apachectl -M which shows all loaded modules Most importantly in the list of loaded modules i got Loaded Modules: php5_module (shared) Since the module is being loaded, it seems like the issue has more to do with making apache use php engine to process the php files.... so something wrong with the ifmodule directive?

    Read the article

  • Occasional "Could not load file or assembly" in asmx WebService on IIS and DFS

    - by jesse-mcdowell
    We have a handfull of ASMX web service hosted on two identical Windows Server 2003 boxes. The virtual directory for the web services is loaded in a DFS share, both servers point to the same share. We have a load balancer between the internet and the two web servers. At a seemingly random interval (right now about twice per week) when a user tries to access a method on the web service, IIS returns the error: "Could not load file or assembly" for one of the assemblies used in the method call, and will continue reporting it each time the method is called until the app pool is recycled. We haven't found any distinguishable pattern to the problem. This is what I know: the missing assembly varies (but it's always a home-brew assembly) the Web Service method that fails varies there is no noticeable pattern to the times or intervals where the problem appears there are no admin users accessing the servers when the problem appears the failing method will work correctly on one server and fail on the other, even though both point to the same bin folder the problem can always be corrected by recycling the app pool and making no other changes I have enabled the Assembly Binder Log, and know that the binder is looking in the correct location for the file. Our assemblies are compiled for .Net 3.5.

    Read the article

  • In Windows 7, why can't I use perfmon against a remote server?

    - by SomeGuy
    I am on Windows 7 and trying to run perfmon against Windows 2003 and Windows 2008 servers. I am running into the same issue with all remote machines. When creating a data collector set, I specify a domain account that is in the administrators group on the remote machines (and "Performance Log Users" and "Performance Monitor Users" to be safe). On the "Available Counters" screen, When I type in a remote computer name, PerfMon locks up for a good 2-3 minutes before I can add any counters. I can then save the collector set. However, when I save it, the go/stop buttons are disabled if I click the set in the left panel, and missing if I click the Data collector set itself in the right panel. See the screens below. I can run data collector sets against my local machine with no problem. I am opening perfmon with my local account in both scenarios. I also have Remote Registry Service started on each remote machine. What is going on?

    Read the article

  • PHP unable to load dynamic library... but it is loaded. WTF?

    - by Josh
    I have a CentOS 5.4 server with Apache 2.2.3, mod_fastcgi and PHP 5.2.11. Everything is working great, server is a production server and I've had no complaints. When I was looking in PHP's error log to diagnose a problem with a specific page, I saw the following periodically repeated over and over: [03-May-2010 19:54:12] PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/apc.so' - /usr/lib/php/modules/apc.so: undefined symbol: php_rfc1867_callback in Unknown on line 0 [03-May-2010 19:54:12] PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/pdo_mysql.so' - /usr/lib/php/modules/pdo_mysql.so: undefined symbol: php_pdo_get_dbh_ce in Unknown on line 0 [03-May-2010 19:54:12] PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/apc.so' - /usr/lib/php/modules/apc.so: undefined symbol: php_rfc1867_callback in Unknown on line 0 [03-May-2010 19:54:12] PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/pdo_mysql.so' - /usr/lib/php/modules/pdo_mysql.so: undefined symbol: php_pdo_get_dbh_ce in Unknown on line 0 I am very confused because APC is loaded, I can see it in the output of phpinfo(). And by the look of these error messages nothing should be working at all. Yet sites seem to be running fine. How can I track down the source of this error?

    Read the article

  • How should secret files be pushed to an EC2 (on AWS) Ruby on Rails application?

    - by nikc
    How should secret files be pushed to an EC2 Ruby on Rails application using amazon web services with their elastic beanstalk? I add the files to a git repository, and I push to github, but I want to keep my secret files out of the git repository. I'm deploying to aws using: git aws.push The following files are in the .gitignore: /config/database.yml /config/initializers/omniauth.rb /config/initializers/secret_token.rb Following this link I attempted to add an S3 file to my deployment: http://docs.amazonwebservices.com/elasticbeanstalk/latest/dg/customize-containers.html Quoting from that link: Example Snippet The following example downloads a zip file from an Amazon S3 bucket and unpacks it into /etc/myapp: sources: /etc/myapp: http://s3.amazonaws.com/mybucket/myobject Following those directions I uploaded a file to an S3 bucket and added the following to a private.config file in the .elasticbeanstalk .ebextensions directory: sources: /var/app/current/: https://s3.amazonaws.com/mybucket/config.tar.gz That config.tar.gz file will extract to: /config/database.yml /config/initializers/omniauth.rb /config/initializers/secret_token.rb However, when the application is deployed the config.tar.gz file on the S3 host is never copied or extracted. I still receive errors that the database.yml couldn't be located and the EC2 log has no record of the config file, here is the error message: Error message: No such file or directory - /var/app/current/config/database.yml Exception class: Errno::ENOENT Application root: /var/app/current

    Read the article

  • Network connection to Firebird 2.1 became slow after upgrading to Ubuntu 10.04

    - by lyle
    We've got a setup that we're using for different clients : a program connecting to a Firebird server on a local network. So far we mostly used 32bit processors running Ubuntu LTS (recently upgraded to 10.04). Now we introduced servers running on 64bit processors, running Ubuntu 10.04 64bit. Suddenly some queries run slower than they used to. In short: running the query locally works fine on both 64bit and 32bit servers, but when running the same queries over the network the 64bit server is suddenly much slower. We did a few checks with both local and remote connections to both 64bit and 32bit servers, using identical databases and identical queries, running in Flamerobin. Running the query locally takes a negligible amount of time: 0.008s on the 64bit server, 0.014s on the 32bit servers. So the servers themselves are running fine. Running the queries over the network, the 64bit server suddenly needs up to 0.160s to respond, while the 32bit server responds in 0.055s. So the older servers are twice as fast over the network, in spite of the newer servers being twice as fast if run locally. Apart from that the setup is identical. All servers are running the same installation of Ubuntu 10.04, same version of Firebird and so on, the only difference is that some are 64 and some 32bit. Any idea?? I tried to google it, but I couldn't find any complains that Firebird 64bit is slower than Firebird 32bit, except that the Firebird 2.1 change log mentions that there's a new network API which is twice as fast, as soon as the drivers are updated to use it. So I could imagine that the 64bit driver is still using the old API, but that's a bit of a stretch, I guess. Thanx in advance for any replies! :)

    Read the article

  • Windows Update Agent Update Failed

    - by Adrian Godong
    I'm trying to install the latest version of Windows Update Agent, v7.2.6001.788, and the installation failed with error code of 0x800b0100. Running Windows Server 2008 SP1. The relevant WindowsUpdate.log section: 2009-08-03 16:17:49:334 3544 d28 Misc =========== Logging initialized (build: 7.2.6001.788, tz: +0100) =========== 2009-08-03 16:17:49:334 3544 d28 Misc = Process: d:\fcc0f96e893296900e6501a601\wusetup.exe 2009-08-03 16:17:49:332 3544 d28 Setup Windows Update Client standalone setup : resource dll path is d:\fcc0f96e893296900e6501a601\en\wusetup.exe.mui 2009-08-03 16:17:49:335 3544 d28 Setup Evaluating CBS package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-Core-TopLevel.cab" 2009-08-03 16:17:49:556 3544 d28 Setup Package will be installed 2009-08-03 16:17:49:556 3544 d28 Setup Evaluating CBS package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-ActiveX.cab" 2009-08-03 16:17:49:580 3544 d28 Setup Package will be installed 2009-08-03 16:17:49:580 3544 d28 Setup Evaluating CBS package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-Aux-TopLevel.cab" 2009-08-03 16:17:49:665 3544 d28 Setup Package will be installed 2009-08-03 16:17:49:709 3544 d28 Setup Windows Update Client standalone setup : eula file path is d:\fcc0f96e893296900e6501a601\en\eula.rtf 2009-08-03 16:17:52:337 3544 de0 Misc WARNING: LoadLibrary failed for srclient.dll with hr:8007007E 2009-08-03 16:17:52:338 3544 de0 Setup Installing CBS package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-Core-TopLevel.cab" 2009-08-03 16:17:53:895 3544 de0 Setup WARNING: CBS operation failed, error = 0x800B0100 2009-08-03 16:17:53:898 3544 de0 Setup WARNING: Install of setup package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-Core-TopLevel.cab" failed, error = 0x800B0100 2009-08-03 16:18:04:976 3544 d28 Setup wusetup has finished. Exit code is 0. Reboot is NOT needed I think something went wrong twhen loading the srclient.dll. Things that I have done and still no fix: msiexec /unregister and msiexec /register regsvr32 wuapi.dll Run CheckSUR tool and restart

    Read the article

  • Mounting NAS drive with cifs using credentials file through fstab does not work

    - by mahatmanich
    I can mount the drive in the following way, no problem there: mount -t cifs //nas/home /mnt/nas -o username=username,password=pass\!word,uid=1000,gid=100,rw,suid However if I try to mount it via fstab I get the following error: //nas/home /mnt/nas cifs iocharset=utf8,credentials=/home/username/.smbcredentials,uid=1000,gid=100 0 0 auto .smbcredentials file looks like this: username=username password=pass\!word Note the ! in my password ... which I am escaping in both instances I also made sure there are no eol in the file using :set noeol binary from Mount CIFS Credentials File has Special Character chmod on .credentials file is 0600 and chown is root:root file is under ~/ Why am I getting in on the one side and not with fstab?? I am running on ubuntu 12 LTE and mount.cifs -V gives me mount.cifs version: 5.1 Any help and suggestions would be appreciated ... UPDATE: /var/log/syslog shows following [26630.509396] Status code returned 0xc000006d NT_STATUS_LOGON_FAILURE [26630.509407] CIFS VFS: Send error in SessSetup = -13 [26630.509528] CIFS VFS: cifs_mount failed w/return code = -13 UPDATE no 2 Debugging with strace mount through fstab: strace -f -e trace=mount mount -a Process 4984 attached Process 4983 suspended Process 4985 attached Process 4984 suspended Process 4984 resumed Process 4985 detached [pid 4984] --- SIGCHLD (Child exited) @ 0 (0) --- [pid 4984] mount("//nas/home", ".", "cifs", 0, "ip=<internal ip>,unc=\\\\nas\\home"...) = -1 EACCES (Permission denied) mount error(13): Permission denied Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) Process 4983 resumed Process 4984 detached Mount through terminal strace -f -e trace=mount mount -t cifs //nas/home /mnt/nas -o username=user,password=pass\!wd,uid=1000,gid=100,rw,suid Process 4990 attached Process 4989 suspended Process 4991 attached Process 4990 suspended Process 4990 resumed Process 4991 detached [pid 4990] --- SIGCHLD (Child exited) @ 0 (0) --- [pid 4990] mount("//nas/home", ".", "cifs", 0, "ip=<internal ip>,unc=\\\\nas\\home"...) = 0 Process 4989 resumed Process 4990 detached

    Read the article

  • Freeradius authentication failed for unknown reason

    - by Moein7tl
    I followed this instruction to force freeradius to use mysql database. and run freeradius in debug mod. but it rejects all authentication. mysql database : mysql select * from radcheck; +----+----------+-----------+----+---------+ | id | username | attribute | op | value | +----+----------+-----------+----+---------+ | 1 | test | Password | == | test123 | | 2 | test | Auth-Type | == | Local | +----+----------+-----------+----+---------+ 2 rows in set (0.02 sec) radtest command : # radtest test test123 localhost 0 testing123 Sending Access-Request of id 235 to 127.0.0.1 port 1812 User-Name = "test" User-Password = "test123" NAS-IP-Address = 127.0.0.1 NAS-Port = 0 Message-Authenticator = 0x00000000000000000000000000000000 rad_recv: Access-Reject packet from host 127.0.0.1 port 1812, id=235, length=20 radiusd debug mod log: rad_recv: Access-Request packet from host 127.0.0.1 port 51034, id=235, length=74 User-Name = "test" User-Password = "test123" NAS-IP-Address = 127.0.0.1 NAS-Port = 0 Message-Authenticator = 0xbf111cbbae24fb0f0a558bfa26f53476 # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop ++[mschap] returns noop ++[digest] returns noop [suffix] No '@' in User-Name = "test", looking up realm NULL [suffix] No such realm "NULL" ++[suffix] returns noop [eap] No EAP-Message, not doing EAP ++[eap] returns noop ++[files] returns noop ++[expiration] returns noop ++[logintime] returns noop [pap] WARNING! No "known good" password found for the user. Authentication may fail because of this. ++[pap] returns noop ERROR: No authenticate method (Auth-Type) found for the request: Rejecting the user Failed to authenticate the user. Using Post-Auth-Type Reject # Executing group from file /usr/local/etc/raddb/sites-enabled/default +- entering group REJECT {...} [attr_filter.access_reject] expand: %{User-Name} - test attr_filter: Matched entry DEFAULT at line 11 ++[attr_filter.access_reject] returns updated Delaying reject of request 20 for 1 seconds Going to the next request Waking up in 0.9 seconds. Sending delayed reject for request 20 Sending Access-Reject of id 235 to 127.0.0.1 port 51034 Waking up in 4.9 seconds. Cleaning up request 20 ID 235 with timestamp +4325 Ready to process requests. where is the problem and how should I solve it?

    Read the article

  • SSH garbling characters in vim/nano on remote server

    - by geerlingguy
    ... and it's driving me insane. Basically (this has been happening over the past couple months), I log into a few different CentOS servers (one Linode, another VPS, and a shared host to which I have shell access), running 5.5, 5.7, and 6, from my Mac running OS X Lion, using Terminal. Basically: $ ssh [email protected] [remote-host] $ nano somefile.txt Once I start editing the file, if I use the arrow keys to move around the cursor, or start deleting, then typing again, the cursor jumps around a bit, and if I save the file and reopen it, it's obvious that the cursor was, in fact, jumping all over the place on a line for no apparent reason. I end up getting things like "This is a neof text." When I had typed in (to the cursor-crazy editor) "This is a line of text." It's a big problem when it comes to editing configuration files, because I often have to edit one line, save and close, then reopen just to make sure that line is right... then edit another line... and it's getting quite annoying. I found Linode Lish Shell Vim and Nano rendering troubles: lines not appearing / cursor positions wrong, but I don't know if that relates much, since that's specifically referring to lish.

    Read the article

  • missing network usage through iptables

    - by Purres
    I inserted a rule to iptables to track the input usage to a certain ip address. The vps server's IP is 192.168.1.5 and the guest os's IP is 192.168.1.115. I ran 'yum update' inside the guest OS to get some network traffic. Then I ran iptables -vnL from the hypervisor. However it only showed network usage to the host, but not to the guest. Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target source destination 0 0 0.0.0.0/0 0.0.0.0/0 destination IP range 192.168.1.115-192.168.1.115 1853 114K 0.0.0.0/0 0.0.0.0/0 destination IP range 192.168.1.5-192.168.1.5 I ran tcpdump and the log showed that there're data packets to the guest os. 16:17:43.932514 IP mirrordenver.fdcservers.net.http > 192.168.1.115.34471: Flags [.], seq 17694667:17696115, ack 1345, win 113, options [nop,nop,TS val 1060308643 ecr 1958781], length 1448 16:17:43.932559 IP 192.168.1.115.34471 > mirrordenver.fdcservers.net.http: Flags [.], ack 17696115, win 15287, options [nop,nop,TS val 1958869 ecr 1060308643], length 0 Why the guest OS network usage couldn't be tracked? iptables -L will return the INPUT chain as following: Chain INPUT (policy ACCEPT) target prot opt source destination all -- anywhere anywhere destination IP range 192.168.1.115-192.168.1.115 all -- anywhere anywhere destination IP range 192.168.1.5-192.168.1.5 all -- anywhere anywhere

    Read the article

  • Apache 2.2, worker mpm, mod_fcgid and PHP: Can't apply process slot

    - by mopoke
    We're having an issue on an apache server where every 15 to 20 minutes it stops serving PHP requests entirely. On occasions it will return a 503 error, other times it will recover enough to serve the page but only after a delay of a minute or more. Static content is still served during that time. In the log file, there's errors reported along the lines of: [Wed Sep 28 10:45:39 2011] [warn] mod_fcgid: can't apply process slot for /xxx/ajaxfolder/ajax_features.php [Wed Sep 28 10:45:41 2011] [warn] mod_fcgid: can't apply process slot for /xxx/statics/poll/index.php [Wed Sep 28 10:45:45 2011] [warn] mod_fcgid: can't apply process slot for /xxx/index.php [Wed Sep 28 10:45:45 2011] [warn] mod_fcgid: can't apply process slot for /xxx/index.php There is RAM free and, indeed, it seems that more php processes get spawned. /server-status shows lots of threads in the "W" state as well as some FastCGI processes in "Exiting(communication error)" state. I rebuilt mod_fcgid from source as the packaged version was quite old. It's using current stable version (2.3.6) of mod_fcgid. FCGI config: FcgidBusyScanInterval 30 FcgidBusyTimeout 60 FcgidIdleScanInterval 30 FcgidIdleTimeout 45 FcgidIOTimeout 60 FcgidConnectTimeout 20 FcgidMaxProcesses 100 FcgidMaxRequestsPerProcess 500 FcgidOutputBufferSize 1048576 System info: Linux xxx.com 2.6.28-11-server #42-Ubuntu SMP Fri Apr 17 02:45:36 UTC 2009 x86_64 GNU/Linux DISTRIB_ID=Ubuntu DISTRIB_RELEASE=9.04 DISTRIB_CODENAME=jaunty DISTRIB_DESCRIPTION="Ubuntu 9.04" Apache info: Server version: Apache/2.2.11 (Ubuntu) Server built: Aug 16 2010 17:45:55 Server's Module Magic Number: 20051115:21 Server loaded: APR 1.2.12, APR-Util 1.2.12 Compiled using: APR 1.2.12, APR-Util 1.2.12 Architecture: 64-bit Server MPM: Worker threaded: yes (fixed thread count) forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/worker" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="" -D SUEXEC_BIN="/usr/lib/apache2/suexec" -D DEFAULT_PIDLOG="/var/run/apache2.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="/etc/apache2/mime.types" -D SERVER_CONFIG_FILE="/etc/apache2/apache2.conf" Apache modules loaded: alias.load auth_basic.load authn_file.load authz_default.load authz_groupfile.load authz_host.load authz_user.load autoindex.load cgi.load deflate.load dir.load env.load expires.load fcgid.load headers.load include.load mime.load negotiation.load rewrite.load setenvif.load ssl.load status.load suexec.load PHP info: PHP 5.2.6-3ubuntu4.6 with Suhosin-Patch 0.9.6.2 (cli) (built: Sep 16 2010 19:51:25) Copyright (c) 1997-2008 The PHP Group Zend Engine v2.2.0, Copyright (c) 1998-2008 Zend Technologies

    Read the article

  • Drobo FS vs. MacBook Pro: Finder works, Drobo Dashboard doesn't

    - by dash-tom-bang
    Does anyone have any experience with the new Drobo FS, specifically using it from a MacBook Pro? My experience thus far is this: Set up the Drobo Dashboard software (hereinafter called simply 'Dashboard') on my WinXP machine, which is hard-wired to the network to do the data migration from my NAS-that's-being-replaced (a 250G SimpleShare which works well enough but I was always afraid of losing the one disk). The Dashboard seems to work ok, except that the DroboCopy function doesn't work at all. This is the backup solution, which I can configure, and if I launch it (e.g. to back up from the old NAS to the Drobo) it spins the NAS, seeking the drive all over hell and creation, until finally giving up an hour+ later with zero files copied. Selecting only a subset of the data yields the same effect albeit more quickly. On my Mac I installed the Dashboard software too, since most of my fiddling with the device will be from my couch in the living room. Finder connects to the box just fine, fwiw, but Dashboard just sits there, "waiting for connection." This is considerably more bothersome than the above paragraph, but I figured I'd give whatever information I have. Drobo is insisting that I send them this "Debug Log" file that their software generates. Does anyone know what's in it? It's encrypted and they won't tell me, which spooks me just a bit; not like I'm terribly concerned about privacy but I don't want to be sending personal information out to every clown who says they "need" it in order to help me. thanks a ton, -tom!

    Read the article

  • ProFTPD / PAM issues with new centos/virtualmin install

    - by iamthewit
    I just installed CentOS 5.4 on a rackspace cloud server and installed virtualmin which all seemed to go fine. The only problem I have is that I can not access the virtual servers directories via FTP. I get the following from filezilla: Status: Connecting to 1.1.1.1:21... Status: Connection established, waiting for welcome message... Response: 220 FTP Server ready. Command: USER username Response: 331 Password required for username. Command: PASS *************** Response: 230 User username logged in. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is current directory. Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (1,1,1,1,216,214) Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing and I get this from my /var/secure/log file Sep 22 19:40:42 stickeeserver proftpd: pam_unix(proftpd:session): session opened for user username by (uid=0) Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - USER nastypasty: Login successful. Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - Preparing to chroot to directory '/home/username' Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - mod_delay/0.5: delaying for 728 usecs Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - error setting IPV6_V6ONLY: Protocol not available Any help would be greatly appreciated, I'm not totally new to Linux but it's not my strongest subject. I do like to know exactly why problems occur though and how exactly to fix them so the more detail the better! cheers

    Read the article

  • JAVASCRIPT ENABLED

    - by kirchoffs415
    HI, I hope somebody can help, i keep getting the following message when i log on-- Your Javascript is disabled. Limited functionality is available. it will stay for maybe a day sometimes two.I have uninstalled javascript and reinstalled but still the same. Iam using chrome. any help would be gratefull many thanks Dominic p.s. my system spec is as follows System InformationOS Name Microsoft® Windows Vista™ Home Premium Version 6.0.6002 Service Pack 2 Build 6002 Other OS Description Not Available OS Manufacturer Microsoft Corporation System Name DOM-PC System Manufacturer Dell Inc. System Model Inspiron 1545 System Type X86-based PC Processor Pentium(R) Dual-Core CPU T4200 @ 2.00GHz, 2000 Mhz, 2 Core(s), 2 Logical Processor(s) BIOS Version/Date Dell Inc. A05, 25/02/2009 SMBIOS Version 2.4 Windows Directory C:\Windows System Directory C:\Windows\system32 Boot Device \Device\HarddiskVolume3 Locale United Kingdom Hardware Abstraction Layer Version = "6.0.6002.18005" User Name DOM-PC\DOM Time Zone GMT Standard Time Installed Physical Memory (RAM) 3.00 GB Total Physical Memory 2.96 GB Available Physical Memory 1.38 GB Total Virtual Memory 5.89 GB Available Virtual Memory 4.25 GB Page File Space 3.00 GB Page File C:\pagefile.sys My System Specs

    Read the article

  • Run script before shutdown/restart

    - by dtbarne
    I'd like to run a PHP script when an instance is told to shutdown, but of course before it actually finishes shutting down. My particular script is just looking to push some log files from the local partition to a another server. I've got the gist of how this process works, but I need some clarification. How I understand it. Please correct me if I'm wrong. Create an executable script in /etc/init.d (lets call it /etc/init.d/push-logs) Create a symlink to /etc/init.d/push-logs from /etc/rc0.d (shutdown) and /etc/rc6.d (reboot). The name should be KXXpush-logs Here's my questions: Of course - am I understanding correctly? For #2 above - it sounds like the lower the XX the better - is there too low a number I can use? Does it matter if it shares a number with another script? Does the script in /etc/init.d/push-logs HAVE to follow the standard init.d template (supporting start/stop, etc. commands)? This doesn't really apply to my use case. If possible I just want the script to be the following: #!/bin/sh # # Run PHP file prior to shutdown # /usr/bin/php /path/to/php_file.php

    Read the article

  • Gluster bricks are offline and errors in logs

    - by Roman Newaza
    I have substituted all the IP addresses with hostnames and renamed configs (IP to hostname) in /var/lib/glusterd by my shell script. After that I restarted Gluster Daemon and the volume. Then I checked if all the peers are connected: root@GlusterNode1a:~# gluster peer status Number of Peers: 3 Hostname: gluster-1b Uuid: 47f469e2-907a-4518-b6a4-f44878761fd2 State: Peer in Cluster (Connected) Hostname: gluster-2b Uuid: dc3a3ff7-9e30-44ac-9d15-00f9dab4d8b9 State: Peer in Cluster (Connected) Hostname: gluster-2a Uuid: 72405811-15a0-456b-86bb-1589058ff89b State: Peer in Cluster (Connected) I could see mounted volumes size change on all the nodes when I execute df command, so new data is coming. But recently I noticed error messages in app log: copy(/storage/152627/dat): failed to open stream: Structure needs cleaning readfile(/storage/1438227/dat): failed to open stream: Input/output error unlink(/storage/189457/23/dat): No such file or directory Finally, I have found out some bricks are offline: root@GlusterNode1a:~# gluster volume status Status of volume: storage Gluster process Port Online Pid ------------------------------------------------------------------------------ Brick gluster-1a:/storage/1a 24009 Y 1326 Brick gluster-1b:/storage/1b 24009 N N/A Brick gluster-2a:/storage/2a 24009 N N/A Brick gluster-2b:/storage/2b 24009 N N/A Brick gluster-1a:/storage/3a 24011 Y 1332 Brick gluster-1b:/storage/3b 24011 N N/A Brick gluster-2a:/storage/4a 24011 N N/A Brick gluster-2b:/storage/4b 24011 N N/A NFS Server on localhost 38467 Y 24670 Self-heal Daemon on localhost N/A Y 24676 NFS Server on gluster-2b 38467 Y 4339 Self-heal Daemon on gluster-2b N/A Y 4345 NFS Server on gluster-2a 38467 Y 1392 Self-heal Daemon on gluster-2a N/A Y 1402 NFS Server on gluster-1b 38467 Y 2435 Self-heal Daemon on gluster-1b N/A Y 2441 What can I do about that? I need to fix it. Note: CPU and Network usage of all the four nodes are about the same.

    Read the article

  • How to bypass firewall to connect to a proxy server?

    - by Bruce
    I am conducting a small experiment on my office network. I have setup a proxy server on my desktop machine (connected to my LAN) and I have volunteers access the internet via my proxy server. Everything is working well. The problem is people cannot connect to the proxy server through their laptops. I asked my network admin and he said the wireless network has a firewall which prevents users from connecting to my proxy. He said I could tunnel the traffic or use SSH though. I am afraid I do not understand fully what is going on. Is there a way by which users connected on the wireless network can connect to my desktop? I am using FreeProxy on Windows as my proxy server: http://www.handcraftedsoftware.org/index.php?page=download FreeProxy allows me to create a SOCKS 4/4a/5 proxy. Is that what I need? Part of the experiment involves logging the URL requests of the users. I am doing a measurement study. So, any solution must allow me to log the URL requests of users. Also, what changes do I need to make in the browser configuration.

    Read the article

  • mcelog doesn't fails to start PUIAS 6.4 amd hardware

    - by Predrag Punosevac
    Folks, I am a total Linux n00b. I am trying to deploy mcelog on one of my computing nodes running PUIAS 6.4 (i86_64) [root@lov3 edac]# uname -a Linux lov3.mylab.org 2.6.32-358.18.1.el6.x86_64 #1 SMP Tue Aug 27 22:40:32 EDT 2013 x86_64 x86_64 x86_64 GNU/Linux a free clone of Red Hat 6.4 on AMD hardware [root@lov3 mcelog]# lscpu Architecture: x86_64 CPU op-mode(s): 32-bit, 64-bit Byte Order: Little Endian CPU(s): 64 On-line CPU(s) list: 0-63 Thread(s) per core: 2 Core(s) per socket: 8 Socket(s): 4 NUMA node(s): 8 Vendor ID: AuthenticAMD CPU family: 21 Model: 2 Stepping: 0 CPU MHz: 1400.000 BogoMIPS: 4999.30 Virtualization: AMD-V L1d cache: 16K L1i cache: 64K L2 cache: 2048K L3 cache: 6144K NUMA node0 CPU(s): 0-7 NUMA node1 CPU(s): 8-15 NUMA node2 CPU(s): 16-23 NUMA node3 CPU(s): 24-31 NUMA node4 CPU(s): 32-39 NUMA node5 CPU(s): 40-47 NUMA node6 CPU(s): 48-55 NUMA node7 CPU(s): 56-63 My mcelog.conf file is more or less default apart of the fact that I would like to run mcelog as a daemon and to log errors. When I start mcelog [root@lov3 mcelog]# mcelog --config-file mcelog.conf AMD Processor family 21: Please load edac_mce_amd module. However the module is present [root@lov3 mcelog]# locate edac_mce_amd.ko /lib/modules/2.6.32-358.18.1.el6.x86_64/kernel/drivers/edac/edac_mce_amd.ko /lib/modules/2.6.32-358.el6.x86_64/kernel/drivers/edac/edac_mce_amd.ko and loaded [root@lov3 edac]# lsmod | grep mce edac_mce_amd 14705 1 amd64_edac_mod Is there anything that I can do to get mcelog working? The only reference I found is this thread http://lists.centos.org/pipermail/centos/2012-November/130226.html

    Read the article

  • Permission denied when running Rails app in VirtualBox Ubuntu guest with files on Windows host

    - by Ola Tuvesson
    I think I'm close to having my dev environment set up exactly the way I want, but one final snag remains. I'm running VirtualBox on a Windows 7 64bit host, with my dev enviroment inside a Ubuntu 12.04 guest. I want to keep the files for my projects on the host filesystem - partly so I can access them when the Ubuntu guest is not running, but also so I can use Tortoise and other Windows based tools (cough Photoshop), and it also eases my backup scheme somewhat. So I've got a folder "Rails" on my NTFS drive, which I've shared (Samba) from the host with a user specifically created for the Ubuntu guest. The mount point has been set up and an entry added to fstab (cifs), using a credentials file and the options iocharset=utf8,mode=0777,dir_mode=07??77 This mounts fine and my Ubuntu user has both read and write permissions to the contents. But when I try to start my Rails app I get permission errors on any files the app needs to write to (e.g. the log file) - why is that? Are there any major conceptual flaws with this approach? Would I be better off using the VBox "shared folders" function?

    Read the article

  • How to fix a Postfix/MySQL/Dovecot Unknown Host Issue?

    - by thiesdiggity
    I am having an issue with one of my Postfix/Dovecot mail servers and I'm unsure how to fix the problem. I will try to explain it in detail, here it goes: I have an Ubuntu server setup using Virtual hosting with Postfix, Dovecot and MySQL. We have one domain setup as a virtual domain, for this example I am going to use mail.example.com. Under that domain we have one email address. I have another server (MS Exchange) setup using another one of my sub-domains, ex.example.com. The problem is that when I SMTP into the account on mail.example.com and try to send an email to an account on ex.example.com, I get the email returned back to us with an "unknown host" error. Now, I know that the mail.example.com server can resolve the ex.example.com domain because I can ping/dig while SSH'd into it. I can also log into Postfix via Telnet and send an email to an ex.example.com mailbox. I'm guessing that it has something to do with Postfix/Dovecot looking locally for the domain in the virtual domain list because of the tld domain (example.com)? If that's the case, how do I get Postfix/Dovecot to only look locally for the entire URL (mail.example.com) and if it doesn't find it, send it to the correct server by looking up the MX/A records (which I know exist and are setup correctly)? I have been working on this all day and any guidance would be GREATLY appreciated! Thanks for your time!

    Read the article

< Previous Page | 539 540 541 542 543 544 545 546 547 548 549 550  | Next Page >