Search Results

Search found 4509 results on 181 pages for 'logical domains'.

Page 55/181 | < Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >

• What is "2LUN" mode in connection with RAID?

  - by naxa

  I've came across RAID products that also list JBOD (just a bunch of disks) mode and 2LUN mode. What the heck is 2LUN mode? I could not find a description; the closest thing seems to be LUN 'logical unit number' but I don't get the 2LUN thing. UPDATE 1 This is what Wikipedia has to say about JBOD: JBOD (derived from "just a bunch of disks"): an architecture involving multiple hard drives, while making them accessible either as independent hard drives, or as a combined (spanned) single logical volume with no actual RAID functionality. So JBOD can actually mean two different (albeit related) things. Answer of Guest says 2LUN means no spanning. Does this suggest that 2LUN would simply mean the JBOD-variant with no span?

  Read the article

• High I/O latency with software RAID, LUKS encrypted and LVM partitioned KVM setup

  - by aef

  I found out a performance problems with a Mumble server, which I described in a previous question are caused by an I/O latency problem of unknown origin. As I have no idea what is causing this and how to further debug it, I'm asking for your ideas on the topic. I'm running a Hetzner EX4S root server as KVM hypervisor. The server is running Debian Wheezy Beta 4 and KVM virtualisation is utilized through LibVirt. The server has two different 3TB hard drives as one of the hard drives was replaced after S.M.A.R.T. errors were reported. The first hard disk is a Seagate Barracuda XT ST33000651AS (512 bytes logical, 4096 bytes physical sector size), the other one a Seagate Barracuda 7200.14 (AF) ST3000DM001-9YN166 (512 bytes logical and physical sector size). There are two Linux software RAID1 devices. One for the unencrypted boot partition and one as container for the encrypted rest, using both hard drives. Inside the latter RAID device lies an AES encrypted LUKS container. Inside the LUKS container there is a LVM physical volume. The hypervisor's VFS is split on three logical volumes on the described LVM physical volume: one for /, one for /home and one for swap. Here is a diagram of the block device configuration stack: sda (Physical HDD) - md0 (RAID1) - md1 (RAID1) sdb (Physical HDD) - md0 (RAID1) - md1 (RAID1) md0 (Boot RAID) - ext4 (/boot) md1 (Data RAID) - LUKS container - LVM Physical volume - LVM volume hypervisor-root - LVM volume hypervisor-home - LVM volume hypervisor-swap - … (Virtual machine volumes) The guest systems (virtual machines) are mostly running Debian Wheezy Beta 4 too. We have one additional Ubuntu Precise instance. They get their block devices from the LVM physical volume, too. The volumes are accessed through Virtio drivers in native writethrough mode. The IO scheduler (elevator) on both the hypervisor and the guest system is set to deadline instead of the default cfs as that happened to be the most performant setup according to our bonnie++ test series. The I/O latency problem is experienced not only inside the guest systems but is also affecting services running on the hypervisor system itself. The setup seems complex, but I'm sure that not the basic structure causes the latency problems, as my previous server ran four years with almost the same basic setup, without any of the performance problems. On the old setup the following things were different: Debian Lenny was the OS for both hypervisor and almost all guests Xen software virtualisation (therefore no Virtio, also) no LibVirt management Different hard drives, each 1.5TB in size (one of them was a Seagate Barracuda 7200.11 ST31500341AS, the other one I can't tell anymore) We had no IPv6 connectivity Neither in the hypervisor nor in guests we had noticable I/O latency problems According the the datasheets, the current hard drives and the one of the old machine have an average latency of 4.12ms.

  Read the article

• VMWare esxi 4.1 storage errors with MD3200

  - by Karl Katzke

  We're seeing some storage errors from the esxi logs relating to our MD3200. I'm sort of a VMWare noob and am not sure where to go from here because I couldn't find a lot of documentation on the VMWare website, and the forums didn't seem to have any posts about it with actual answers. Everything is working, but I'm trying to proactively troubleshoot this. sfcb-vmware_base|StoragePool Cannot get logical disk data from controller 0 sfcb-vmware_base|Volume Cannot get logical disk data from controller 0 sfcb-vmware_base|storelib-GetLDList-ProcessLibCommandCall failed; rval = 0x800E The ESXi boxes are connected directly via SAS to the controller on the MD3200. What do these errors actually mean, and what's a good path to start troubleshooting or solving them?

  Read the article

• Creating CNAME to delegated domain

  - by Starsky

  We are trying to configure F5 to do load balancing on 4 sub domains similar to this article... http://support.f5.com/kb/en-us/solutions/public/0000/200/sol277.html For Example prod.wip.example.com. NS F5NS1.example.com. prod.wip.example.com. NS F5NS2.example.com. test.wip.example.com. NS F5NS1.example.com. test.wip.example.com. NS F5NS2.example.com. Then we want to make cnames instead of delegating individual sub-domains, e.g. myapp.example.com CNAME prod.wip.example.com Microsoft DNS gives an error when I attempt to make the CNAME... dnscmd ns1 /recordadd example.com myapp CNAME myapp.prod.wip.example.com. Command failed: DNS_ERROR_NOT_ALLOWED_UNDER_DELEGATION 9563 (0000255b) The error makes perfect sense, but does anyone know of a way around it? Or are my NS records incorrect for this setup? Thank you, -Steve

  Read the article

• Mod_rewrite not working on ISPConfig 3 Server

  - by Akahadaka

  Problem I recently migrated a Drupal site from a shared hosting server to my own VM. Everything appears to work correctly, except clean urls. My VM Setup Ubuntu 10.04 LAMP ISPConfig 3 What I've tried From reading up on a number of drupal forums I've tried the following in this order Check that mod_rewrite is installed and enabled Changed PHP from FastCGI to Mod_PHP (prefer to use FastCGI or suPHP though to avoid having tmp/files folders with 777 permissions) Changed the Redirect type to L in ISPConfig Sites-domain.com-Redirect Changed /etc/apache2/sites-enabled/000-default <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All ... </Directory> Not sure about points 3 and 4, I do want all domains to be able to use mod_rewrite out of the box. Question Have I done something wrong or am I missing a step? Ultimately I would like to use FastCGI and clean urls working on all ISPConfig 3 domains without having to make any changes to individual domain settings. Any ideas appreciated, I'll try them all.

  Read the article

• Problem with Xen, xvda and sda

  - by Javier J. Salmeron Garcia

  I am creating a cloud for my university using Eucalyptus with Xen (PCs have Debian Squeeze 64 bit installed). I have a problem with the following guest configuration: # # Configuration file for the Xen instance evenmorefinalfoo, created # by xen-tools 4.2 on Thu May 26 11:03:06 2011. # # # Kernel + memory size # kernel = '/boot/vmlinuz-2.6.32-5-xen-amd64' ramdisk = '/boot/initrd.img-2.6.32-5-xen-amd64' vcpus = '1' memory = '128' # # Disk device(s). # root = '/dev/sda2 ro' disk = [ 'file:/home/xen/domains/evenmorefinalfoo/disk.img,sda2,w', 'file:/home/xen/domains/evenmorefinalfoo/swap.img,sda1,w', ] As you can see, the disk and swap images are meant to be mounted on sda1 and sda2. However, when I start the guest, these are mounted on xvda1 xvda2, provoking an error. Is there anything that I can do about that? It seems like it is a Xen error. Thank you in advance,

  Read the article

• Solution to time shifting requirement in Active Directory

  - by MikeR

  Hi, I currently have an active directory that has several child domains (consisting of nothing other than a DC and bespoke application servers) set-up for testing our CRM software, as some of it is date/time sensitive these have been set to dates in the future at some point in the past, which is causing replication errors. I'm working on getting rid of these child domains, but still have a requirement for our testers to be able to time shift. Does anyone know of any solutions that would allow our test environments to have their time changed (always forward), without affecting the production active directory? Is it as simple as creating a separate Forest on the same LAN or would that interfere with my production Forest? Thanks for any advice.

  Read the article

• programatically check if a domain is availible?

  - by acidzombie24

  Using this solution http://serverfault.com/questions/98940/bot-check-if-a-domain-name-is-availible/98956#98956 I wrote a quick script (pasted below) in C# to check if the domain MIGHT be available. A LOT of results come up with taken domains. It looks like all 2 and 3 letter .com domains are taken and it looks like all 3 letter are taken (not including numbers which many are available). Is there a command or website to take my list of domains and check if they are registered or available? using System; using System.Collections.Generic; using System.Linq; using System.Text; using System.Text.RegularExpressions; using System.Diagnostics; using System.IO; namespace domainCheck { class Program { static void Main(string[] args) { var sw = (TextWriter)File.CreateText(@"c:\path\aviliableUrlsCA.txt"); int countIndex = 0; int letterAmount=3; char [] sz = new char[letterAmount]; for(int z=0; z<letterAmount; z++) { sz[z] = '0'; } //*/ List<string> urls = new List<string>(); //var sz = "df3".ToCharArray(); int i=0; while (i <letterAmount) { if (sz[i] == '9') sz[i] = 'a'; else if (sz[i] == 'z') { if (i != 0 && i != letterAmount - 1) sz[i] = '-'; else { sz[i] = 'a'; i++; continue; } } else if (sz[i] == '-') { sz[i] = 'a'; i++; continue; } else sz[i]++; string uu = new string(sz); string url = uu + ".ca"; Console.WriteLine(url); Process p = new Process(); p.StartInfo.UseShellExecute = false; p.StartInfo.RedirectStandardError = true; p.StartInfo.RedirectStandardOutput = true; p.StartInfo.FileName = "nslookup "; p.StartInfo.Arguments = url; p.Start(); var res = ((TextReader) new StreamReader( p.StandardError.BaseStream)).ReadToEnd(); if (res.IndexOf("Non-existent domain") != -1) { sw.WriteLine(uu); if (++countIndex >= 100) { sw.Flush(); countIndex = 0; } urls.Add(uu); Console.WriteLine("Found domain {0}", url); } i = 0; } Console.WriteLine("Writing out list of urls"); foreach (var u in urls) Console.WriteLine(u); sw.Close(); } } }

  Read the article

• Installing Solaris with Window. Disk partitioning problem.

  - by RishiPatel

  I am running windows and want to install the solaris but having hard time while using installer. I have 1 primary partition of 40GB and one extended partition. Extended partition have 4 logical drive. Solaris disk management window show only two partition one is of 40GB(Primary) and second is Extended partition. Can i convert a logical drive into primary partition( I have one free of 25 GB). Please look at the screenshot of disk management utitlity of window. http://img195.imageshack.us/img195/2005/20726948.jpg Is there any way to install solaris without reformatting the and repartitioning whole drive? In case it is not possible how should i partition and using which utility ?

  Read the article

• I am transferring a namserver domain what do I need to update?

  - by Mech Software

  Perhaps I am totally over thinking this but I have a domain name and name servers that are working just fine. I want to transfer the one domain name that I have for my server which is also the name of the nameserver. e.g. mydomain.com with nameservers ns1.mydomain.com ns2.mydomain.com I am transfering the mydomain.com from the current registrar to the one I use for all my other domains. The question is what do I have to update? Once the transfer is complete mydomain.com will have ns1.mydomain.com and ns2.mydomain.com as it's nameservers as it is today. I was wondering though how ns1.mydomain.com and ns2.mydomain.com are resolving if mydomain.com is pointing to ns1 and ns2. Am I over thinking this or am I missing something in the process here? I always just enter the nameserver names when I configure any domains on my server. Do I have to setup A records somewhere for ns1 and ns2 ?

  Read the article

• HP Smart Array; Is it possible to convert Raid1 to Raid0 by dropping a failed drive?

  - by Erik Heppler

  I have a server that was running two 60GB drives as a logical RAID1. At some point the second drive was physically removed and the logical drive has been in "Interim Recovery Mode" for several months now. There's no need for the redundancy of RAID1 on this machine, and I have no intention of replacing the missing drive. If possible I would like to convert the current RAID1 to a single-drive RAID0 by simply dropping the failed drive from the current configuration. I'm only interested in doing this if it can be done in-place. Otherwise I'm perfectly content to leave it in "Interim Recovery Mode" indefinitely.

  Read the article

• Host wildcard subdomains using postfix.

  - by Jack M.

  I'm trying to work out how I can get postfix to accept email for any sub-domain of my main site. I don't have virtual domains, just a long list of sub-domains for local delivery. In specific, I'm feeding python@*.mydomain.com into a Python using the alias file: python: |/www/proc_email.py The Python can handle delivery from there. I envision this looking something along the lines of: mydestination = encendio, localhost.localdomain, localhost, *.mydomain.com I'm running the latest version of postfix on Ubuntu (not rightly sure how to check the version). Thanks in advance.

  Read the article

• CentOS - Add additional hard drive raid arrays on Dell Perc 5/i card

  - by Quanano

  We have a Dell Poweredge 2900 system with Dell Perc 5/i card and 4 SAS hard drives attached, with NTFS partitions on them. We installed CentOS on one raid array on this controller with a different controller and it is working fine. We are now trying to access the drives shown above and they are not being shown in /dev as sdb, etc. sda is the drive that we installed centos on and it has sda1, sda2, sda3, etc. The CDROM has been picked up as well. If I scan for scsi devices then the perc and adaptec controllers are both found. sg0 is the CDROM and sg2 is the centos installed, however I think sg1 is the other drive but I cannot see anyway to mount the partitions, as only the drive is listed in /dev. Thanks. EXTRA INFO fdisk -l: Disk /dev/sda: 72.7 GB, 72746008576 bytes 255 heads, 63 sectors/track, 8844 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x11e3119f Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 8845 70528000 8e Linux LVM Disk /dev/mapper/vg_lal2server-lv_root: 34.4 GB, 34431041536 bytes 255 heads, 63 sectors/track, 4186 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_root doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_swap: 21.1 GB, 21139292160 bytes 255 heads, 63 sectors/track, 2570 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_swap doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_home: 16.6 GB, 16647192576 bytes 255 heads, 63 sectors/track, 2023 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_home doesn't contain a valid partition table These are all from the install hdd not the additional hard drives modprobe a320raid FATAL: Module a320raid not found. lsscsi -v: [0:0:0:0] cd/dvd TSSTcorp CDRWDVD TS-H492C DE02 /dev/sr0 dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0] [4:0:10:0] enclosu DP BACKPLANE 1.05 - dir: /sys/bus/scsi/devices/4:0:10:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:0:10/4:0:10:0] [4:2:0:0] disk DELL PERC 5/i 1.03 /dev/sda dir: /sys/bus/scsi/devices/4:2:0:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:2:0/4:2:0:0] . lsmod: Module Size Used by fuse 66285 0 des_generic 16604 0 ecb 2209 0 md4 3461 0 nls_utf8 1455 0 cifs 278370 0 autofs4 26888 4 ipt_REJECT 2383 0 ip6t_REJECT 4628 2 nf_conntrack_ipv6 8748 2 nf_defrag_ipv6 12182 1 nf_conntrack_ipv6 xt_state 1492 2 nf_conntrack 79453 2 nf_conntrack_ipv6,xt_state ip6table_filter 2889 1 ip6_tables 19458 1 ip6table_filter ipv6 322029 31 ip6t_REJECT,nf_conntrack_ipv6,nf_defrag_ipv6 bnx2 79618 0 ses 6859 0 enclosure 8395 1 ses dcdbas 9219 0 serio_raw 4818 0 sg 30124 0 iTCO_wdt 13662 0 iTCO_vendor_support 3088 1 iTCO_wdt i5000_edac 8867 0 edac_core 46773 3 i5000_edac i5k_amb 5105 0 shpchp 33482 0 ext4 364410 3 mbcache 8144 1 ext4 jbd2 88738 1 ext4 sd_mod 39488 3 crc_t10dif 1541 1 sd_mod sr_mod 16228 0 cdrom 39771 1 sr_mod megaraid_sas 77090 2 aic79xx 129492 0 scsi_transport_spi 26151 1 aic79xx pata_acpi 3701 0 ata_generic 3837 0 ata_piix 22846 0 radeon 1023359 1 ttm 70328 1 radeon drm_kms_helper 33236 1 radeon drm 230675 3 radeon,ttm,drm_kms_helper i2c_algo_bit 5762 1 radeon i2c_core 31276 4 radeon,drm_kms_helper,drm,i2c_algo_bit dm_mirror 14101 0 dm_region_hash 12170 1 dm_mirror dm_log 10122 2 dm_mirror,dm_region_hash dm_mod 81500 11 dm_mirror,dm_log blkid: /dev/sda1: UUID="bc4777d9-ae2c-4c58-96ea-cedb342b8338" TYPE="ext4" /dev/sda2: UUID="j2wRZr-Mlko-QWBR-BndC-V2uN-vdhO-iKCuYu" TYPE="LVM2_member" /dev/mapper/vg_lal2server-lv_root: UUID="9238208a-1daf-4c3c-aa9b-469f0387ebee" TYPE="ext4" /dev/mapper/vg_lal2server-lv_swap: UUID="dbefb39c-5871-4bc9-b767-1ef18f12bd3d" TYPE="swap" /dev/mapper/vg_lal2server-lv_home: UUID="ec698993-08b7-443e-84f0-9f9cb31c5da8" TYPE="ext4" dmesg shows: megaraid_sas: fw state:c0000000 megasas: fwstate:c0000000, dis_OCR=0 scsi2 : LSI SAS based MegaRAID driver scsi 2:0:0:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:1:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:2:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:3:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:4:0: Direct-Access HITACHI HUS154545VLS300 D590 PQ: 0 ANSI: 5 scsi 2:0:5:0: Direct-Access HITACHI HUS154545VLS300 D590 PQ: 0 ANSI: 5 scsi 2:0:8:0: Direct-Access FUJITSU MBA3073RC D305 PQ: 0 ANSI: 5 scsi 2:0:9:0: Direct-Access FUJITSU MBA3073RC D305 PQ: 0 ANSI: 5 i.e. the 3 RAID Arrays Seagate Hitatchi and Fujitsu hard drives respectively. FURTHER UPDATE I have installed the megaraid storage manager console and connected to the server. It appears that the two CentOS installation hard drives are OK. The other 6 drives, one raid array of 4 and one raid array of 2 disks. The other drives are listed as (Foreign) Unconfigured Good.

  Read the article

• Starting with administering a linux box

  - by Josh K

  I'm rather new to this, and I'd like to play with administering a linux box. Things I need to know how to do: Setup subdomains Setup FTP accounts Setup full domains / add domains MySQL setup / install / management LAMP setup / install / management This is probably going on a CentOS distro. I'd like links or a break down on how I can learn to do this. I am comfortable with a command line, but I'm trying to move from shared hosting to a VPS and would like to have some idea on how deep the water is before I do.

  Read the article

• Why is my USB-to-VGA'd monitor working, but not showing in Display Settings?

  - by Strilanc

  I have a USB-to-VGA adapter, which I use to connect a second monitor to my laptop (totaling 3 screens). It worked alright with Vista. I upgraded to Windows 7, and now it no longer works properly (I downloaded the latest drivers just to get it to work on 7). The extra monitor is detected and used to extend the desktop (I can move things onto it, etc), but is not shown within the Control Panel. This is annoying because now I can't changes its resolution, set its logical position to match its physical position, etc. Can I do anything, besides waiting for better drivers? I'm mainly concerned with moving its logical position. (I'd also like to understand how Windows can use a monitor it can't detect. Weird.)

  Read the article

• WBAdmin SystemState Problems

  - by TheD

  I recently installed DHCP on my 2008R2 Server and now Backup Exec and WBAdmin/WSB is having System State issues. Essentially, after some research, I came across a handy tool called VSHADOW which has allowed me to output all the files (and their respective directories) to a text file. And hooray, I think I found the problem: * WRITER "Dhcp Jet Writer" - WriterId = {be9ac81e-3619-421f-920f-4c6fea9e93ad} - InstanceId = {0ed0a8f4-19b0-414d-a3a8-d51d6f4ac8e0} - Supports restore events = TRUE - Writer restore conditions = VSS_WRE_IF_REPLACE_FAILS - Restore method = VSS_RME_RESTORE_AT_REBOOT - Requires reboot after restore = TRUE - Excluded files: - Component "Dhcp Jet Writer:\C:_Windows_system32_dhcp\dhcp" - Name: 'dhcp' - Logical Path: 'C:_Windows_system32_dhcp' - Full Path: '\C:_Windows_system32_dhcp\dhcp' The logical path and Full Path for DHCP is completely wrong. However I can't find where I would change this path, I assume in the registry but I've had no luck finding the key !

  Read the article

• Cannot install grub to RAID1 (md0)

  - by Andrew Answer

  I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat This is the my mdadm output after sync: /dev/md0: Version : 0.90 Creation Time : Wed Feb 17 16:18:25 2010 Raid Level : raid1 Array Size : 470455360 (448.66 GiB 481.75 GB) Used Dev Size : 470455360 (448.66 GiB 481.75 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Nov 1 15:19:31 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 92e6ff4e:ed3ab4bf:fee5eb6c:d9b9cb11 Events : 0.11049560 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. This is my fdisk -l output: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057d19 Device Boot Start End Blocks Id System /dev/sda1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sda2 940910985 976768064 17928540 5 Extended /dev/sda5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table This is my grub install output: root@answe:~# grub-install /dev/sda /usr/sbin/grub-setup: warn: Attempting to install GRUB to a disk with multiple partition labels or both partition label and filesystem. This is not supported yet.. /usr/sbin/grub-setup: error: embedding is not possible, but this is required for cross-disk install. root@answe:~# grub-install /dev/sdb Installation finished. No error reported. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... Anybody can resolve this issue? I have big headache with this.

  Read the article

• Parity Initialization after putting in two new disks

  - by lbanz

  All my firmware is up to date on the server and the controllers. Storage crashed over the weekend. I rebooted it and it detected that I put in two new disks last week (I did check that both disk completed the rebuilding process last week). After it booted into the OS I see that it gave me an information message. After 18 hours it is at 54% so it is looking healthy. But I need to replace 5 more disk in the msa. Should I wait for this message to finish before replacing more disks? 785 Background parity initialization is currently queued or in progress on Logical Drive 1 (15.0 TB, RAID 5). If background parity initialization is queued, it will start when I/O is performed on the drive. When background parity initialization completes, the performance of the logical drive will improve.

  Read the article

• DNS is resolving fine but can't access the server (unless changing /etc/hosts)

  - by victor hugo

  Hi all, I have a VPS server with a public IP, I added some A entries in my name server like svn.example.com - 1.1.1.1 Also I added some entries in my workstation /etc/hosts file in order to work with the domains meanwhile the DNSs were refreshed. It's been around 3 days from this and I configures everything in my server (using the hosts file), the DNSs are ready and I removed the entries but for my surprise I can access the servers nor anything in my domain or sub-domains (even a ping doesn't work). I've triple checked and the DNSs are OK. I don't know too much about DNSs . Any help would be appreciated. The IP address of my VPS is 74.63.223.43 I have these domain names, all pointing to the same IP (using A entries) hartoingenio.com www.hartoingenio.com svn.hartoingenio.com

  Read the article

• Looking for a good Web Server that is cheap

  - by SoLoGHoST

  I am a Project Manager, and former Lead Developer for a software portal system that requires a forum software to run. I am in need of a server that is cheap, reliable, and supports the latest PHP (5.2+), MySQL, unlimited e-mails (preferably), a cPanel, multiple sub-domains (atleast 3+). Currently I am paying $34.95 USD/month (approx. $420 USD/year). This is too high for me to pay to keep the site running. I just recently became Project Manager and in charge of Finances and I'm extremely concerned for the future of Dream Portal. With those prices I'm not sure I'll be able to keep it running for too long. Can someone please tell me of a good server that meets all of the requirements that I listed above that is cheaper on a yearly basis? Note: Currently on a Dedicated Server with limited disk space at 15000 MB (15 GB), monthly bandwidth = 500000 MB, 50 emails limit, 20 sub-domains limit, 30 FTP accts., and 25 SQL Databases.

  Read the article

• Force users to access SSL site using specific host header

  - by mwillmott

  Hi, So i am running IIS7 with one SSL site on it. I have a few different domains and subdomains that all point to my external IP. When using http they all direct to their respective sites using host headers. Whenever someone uses https on any of the domains they all point to my SSL site. I only want people who type in https://sub.domain.com (for example) to end up at my secure site and for anything else to just not go there, it can throw an error or direct to the http version, it doesn't matter. Is there a way of getting IIS7 to check the host header and throw an error if it doesn't match my specific subdomain? Thanks, Michael

  Read the article

• Active Directory remote versus local computer logon

  - by Jake

  Hi, Hope some one can help a network/server noob understand how domains work in AD. I am in an organisation with 2 AD servers in 2 different countries, e.g. US and UK, and they set up the US and UK domains respectively. the accounts are set up such that all employees in both countries have a US\user and UK\user account. What is the difference if a UK user logon with US\user from a local UK computer, versus RDP (remote desktop) into a US server with US\user? Thanks for your help.

  Read the article

• Design Question

  - by dturner71

  Can I have two independent Connection servers attached to the same vCenter server? Here's my scenario. I'm setting up View 4 to provide desktops to two seperate Windows domains that are on different IP subnets seperated by a firewall. One cluster of physical servers, one vCenter server, linked clones. As I understand it View Connection server has to be a member of a Windows domain in order for quickprep to work. So the way to provide desktops to both Windows domains is to have a Connection server in each one right? Then open ports in the firewall so the Connection server from the other subnet can communicate with vCenter. Any reason why this won't work? Or is there a better way to accomplish it?

  Read the article

• Domain pointing to wrong subscription in Plesk 10

  - by Michal Gow

  I recently moved a domain name in the Plesk 10 control panel from one subscription to another. DNS is managed by another server so there is no change in DNS at all. The IP address is shared and remains the same so there is really no need for a DNS change. But the domain is still managed by its former subscription (where it should have been removed from) and is pointing to exactly the same folder as in the past, even when is not in the list of domains there. Subsequently, the new subscription do not have the domain under its control. Even this domain is in list of domains here and points to another folder.

  Read the article

• PostgreSQL RAID configuration

  - by Yoldar-Zi

  I'm stuck how best to configure disk array. We have Hp P2000 G3 disk array with 24 SAS physical disks 300Gb each. We need to configure this array got 2 copies of PostgreSQL 9.2 because two different system. As we know it's recommended to store database and transaction logs(pg_xlog) files on separate disks. So we must setup 4 logical disk: 2 for transaction logs with RAID 1 2 for database with RAID 10 Is this right scheme of distribution? Or may be it is best to just make one big RAID 10 with 4 logical disks?

  Read the article

< Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >