Search Results

Search found 2403 results on 97 pages for 'snatch 02'.

Page 55/97 | < Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• wireless is disabled by hardware lenovo 3000g430

  - by sudheer

  sir i have problem with my wifi switch sir please tell me solution for my problem (wifi is disabled by hardware). output of sudo lshw -C network is sudo] password for sudheer: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: eth2 version: 01 serial: 00:21:00:72:3a:93 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:19 memory:f4700000-f4703fff *-network description: Ethernet interface product: NetLink BCM5906M Fast Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 02 serial: 00:1e:68:ad:24:0b size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=sb v3.04 ip=172.16.52.79 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:47 memory:f4600000-f460ffff output of iwconfig is lo no wireless extensions. eth2 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. sudheer@sudheer:~$ sudo iwlistscanning sudo: iwlistscanning: command not found ***sudheer@sudheer:~$ sudo iwlist scanning*** lo Interface doesn't support scanning. eth2 Failed to read scan data : Invalid argument eth0 Interface doesn't support scanning.

  Read the article

• CUDA & MSI GT60 with Optimus enabled GTX670M?

  - by user1076693

  I have a MSI GT60 Laptop with an Optimus enabled GTX 670M GPU, and I have been trying to get CUDA going in Ubuntu 12.04 environment. I realize that Optimus is not supported in Linux, but I have read the following post suggesting that CUDA works for hybrid GPUs. How can I get nVidia CUDA or OpenCL working on a laptop with nVidia discrete card/Intel Integrated Graphics? I installed the NVIDIA driver via sudo add-apt-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update sudo apt-get install nvidia-current The resulting driver version is 302.17, and supposedly GTX 670M is supported since 295.59. I also downloaded CUDA 4.2 from the NVIDIA site, and compiled it against nvidia-current libraries. Unfortunately, when I run deviceQuery in the CUDA SDK, I get the following output cudaGetDeviceCount returned 38 -> no CUDA-capable device is detected Checking /proc/driver/nvidia/gpus/0/information gives the following Model: GeForce GTX 670M IRQ: 16 GPU UUID: GPU-????????-????-????-????-???????????? Video BIOS: ??.??.??.??.?? Bus Type: PCI-E DMA Size: 32 bits DMA Mask: 0xffffffffff Bus Location: 0000:01.00.0 Here is the output of "lspci | grep VGA" 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 1213 (rev ff) So... what am I doing wrong? Thanks!

  Read the article

• Dell inspiron not finding Vodafone router

  - by Jeggy

  I have a "Dell inspiron 1564" and ubuntu doesn't find my friends router it works great at home, he has a vodafone router jeggy@jeggy-XPS:~$ sudo lshw -C network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: 78:e4:00:2a:d1:eb width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f0200000-f0203fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: b8:ac:6f:67:32:52 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:f0410000-f0410fff memory:f0400000-f040ffff memory:f0420000-f043ffff *-network description: Ethernet interface physical id: 4 logical name: ham0 serial: 7a:79:05:ff:3e:ec size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.255.62.236 link=yes multicast=yes port=twisted pair speed=10Mbit/s

  Read the article

• Lost WiFi after 12.10 upgrade

  - by Steven Guillory

  I received my new Dell Vostro 2420 last week, and just got around to upgrading from 11.10 to 12.10. Unfortunately, like many others (after researching the issue), I no longer have WiFi. I have tried every sudo command given that worked for others, and still can't get my wireless to function. I am new to Linux, so any and all help is appreciated. Thanks in advance! Edit: I can connect via ethernet, just not via wifi. As a matter of fact, when I use Fn + F2 to turn on wifi, only my bluetooth comes on. lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 07:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 09:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) This is what I am getting... dpkg: error: --install needs at least one package archive file argument Type dpkg --help for help about installing and deinstalling packages [*]; Use dselect or aptitude for user-friendly package management; Type dpkg -Dhelp for a list of dpkg debug flag values; Type dpkg --force-help for a list of forcing options; Type dpkg-deb --help for help about manipulating *.deb files; Options marked [*] produce a lot of output - pipe it through less or more !

  Read the article

• Frequent disconnects using wlan AR9285

  - by John Neil

  I'm getting a large number of disconnects from my wireless when I switched to oneiric server (I did not see these happen with oneiric desktop) from my AR9285 wireless LAN device. Here is the syslog snippet: Oct 17 09:43:17 weather kernel: [ 1537.329138] wlan0: deauthenticated from 00:12:17:7a:8e:42 (Reason: 7) Oct 17 09:43:17 weather kernel: [ 1537.340409] cfg80211: All devices are disconnected, going to restore regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340423] cfg80211: Restoring regulatory settings Oct 17 09:43:17 weather kernel: [ 1537.340435] cfg80211: Calling CRDA to update world regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348571] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain Oct 17 09:43:17 weather kernel: [ 1537.348581] cfg80211: World regulatory domain updated: Oct 17 09:43:17 weather kernel: [ 1537.348586] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Oct 17 09:43:17 weather kernel: [ 1537.348594] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348600] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348607] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348613] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Oct 17 09:43:17 weather kernel: [ 1537.348620] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Here is the relevant lspci output: # lspci | grep Atheros 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) I have done quite a bit of searching and saw discussions for previous versions of ubuntu that recommended installing the linux-backports-modules package. However, this does not appear to be available for oneiric (just the headers are listed as a package). Any advice on how to achieve a stable wireless connection for this server? It's location mitigates against using a wired connection.

  Read the article

• Sound not working after installing PCI video card and then removing it

  - by bakhshu

  I am running 11.10 on a HP/Compaq Presario sr1010z, and the video/audio was working fine with whatever was in the machine already. Then I installed a new video card (PCI/nVidia), which disabled the audio/video on the old one automatically. But that card didn't work out too well so I removed it. Now the video is back to normal, but the audio is gone. I have tried the following: 1. In BIOS, set audio to on/enable rather than Auto 2. Looked for hardware in System Settings Sound, but nothing shows up there 3. But when I run the sysinfo utility, I get the description of the audio controller When I do a 'sudo aplay -l', I get 'aplay: device_list:240: no soundcards found...' And then when I do a 'lspci -v | grep -A7 -i "audio"' I get the following: 00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS7012 AC'97 Sound Controller (rev a0) Subsystem: Hewlett-Packard Company Device 2a05 Flags: bus master, medium devsel, latency 32, IRQ 5 I/O ports at a000 [size=256] I/O ports at a400 [size=128] Capabilities: 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Any ideas on how to fix this? Thanks

  Read the article

• Ubuntu 12.04.1 LTS and Nvidia dirver (304.51) 64bit: problem 640x480

  - by nibianaswen

  I have a problem with this configuration: Asus K55V, Ubuntu 12.04 LTS and Nvidia driver 304.51. I have remove the nouveau driver with: apt-get --purge remove xserver-xorg-video-nouveau I installed the official nvidia driver (from www.nvidia.com) but when I reboot the PC the resolution of screen is only 640x480 and the monitor is resized. Mo solution at this problem if i change the xorg.conf. Now i have uninstall the nvidia driver and reinstall with sudo apt-get purge nvidia-current sudo apt-add-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update sudo apt-get install nvidia-current When I reboot the screen resolution and size is OK, but if I start nvidia-setting I received the message: You do not appear to be using the NVIDIA X driver. and with command: sudo lshw -c display | grep driver I received configuration: driver=i915 latency=0 This sound like the system is using the Intel card. When I launch command lspci | grep VGA the output is: 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 1058 (rev ff) And there is no /etc/X11/xorg.conf. I have read a lot of guides on internet but without success.. How i can use nvidia card with the driver that i have installed?

  Read the article

• htaccess correct, Apache logs still showing the evil visitors with 200 code

  - by bulgin

  I hope someone can help me. Please take a look at the following snippet of Apache logs: 95-169-172-157.evilvisitor.com - - [12/Nov/2012:09:46:02 -0500] "GET /the-page-I-dont-want-to-deliver.html HTTP/1.1" 200 9171 "http://hackers.ru/" "Mozilla/4.0 (MSIE 6.0; Windows NT 5.1; Search)" I have the following included in my .htaccess for the root directory of the website and there are no other .htaccess files anywhere that would affect this: RewriteEngine On Options +FollowSymLinks ServerSignature Off ErrorDocument 403 "Nothing Interesting Here" order allow,deny deny from evilvisitor.com deny from hackers.ru deny from anonymouse.org allow from all I also have GeoIP functioning properly and have this included there: #for stuff from different countries RewriteCond %{ENV:GEOIP_COUNTRY_CODE} ^(UA|TR|RU|RO|LV|CZ|IR|HR|KR|TW|NO|NL|NO|IL|SE) RewriteRule ^(.*)$ [R=F,L I know this works because whenever I attempt to access the website from a proxy in say, Spain, I get the error message. I also know it works because when accessing the website from anonymouse.org, the proper error code page is displayed. So then why am I still getting these visitors who successfully access the page I don't want them to see with an Apache 200 code when it should be an error code?

  Read the article

• Restart and/or graphics problem in Ubuntu 12.04

  - by kara

  I having been using 12.04 for a couple of months now, with v. little problems. The other day I restarted my computer, and though I think it rebooted, the screen would be black. I could not even get a visual from a live cd. Finally, I was able to get it to load, but the resolution has been completely off. The computer thinks I have a laptop screen, when I actually have a ViewSonic VP2330wb, and it detects only two resolutions. And still, I have a problem with rebooting. If the screen locks after I leave it for a while, I can't get a visual back, and then when I force a shutdown, it takes 3 times for me to get a grub screen. Then I have to boot in recovery mode, and then finally in normal mode, but the screen is still always off. This is my video card: description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list configuration: latency=0 resources: memory:fe000000-fe3fffff memory:d0000000-dfffffff ioport:f000(size=64) I am a new ubuntu user, and am at my wits end. Any help would be greatly appreciated.

  Read the article

• Ubuntu sound volume is 40% lower than in Windows

  - by ncomx

  I have 2x 2.1 speakers connected to the computer where I have Ubuntu 12.04 installed. On the software side I've set all the volume controls to 100% with the alsamixer program. The speakers have their own volume control, maintaining those at the same level, and switching between Ubuntu and Windows (XP and 7), on windows the output volume is at least 40% higher, even when having the windows volume control at 50% (without touching the speakers volume control) it's still much higher than the sound on Ubuntu. Why can this be happening? Are there some alternative sound drivers (other than the default ones) I could test to see if it makes a difference? some info about the card: root:$ cat /proc/asound/cards 0 [PCH ]: HDA-Intel - HDA Intel PCH HDA Intel PCH at 0xfbff4000 irq 55 1 [Generic ]: HDA-Intel - HD-Audio Generic HD-Audio Generic at 0xfbcfc000 irq 56 root:$ lspci | grep -i audio 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 02:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI Cayman/Antilles HDMI Audio [Radeon HD 6900 Series] I think the one i am using is the Intel one, the other seems to be from the vga card which is an ati radeon 6950. Running gstreamer-properties and switching between alsa, oss, ossv4 and pulseaudio doesn't seem to make any difference.

  Read the article

• How do I fix the HDMI/DVI display output with Intel HD 4000 Graphics in 12.04?

  - by YumYumYum

  I have an Alienware Dell PC with Intel HD 4000 Graphics (Ivy Bridge) as verified by the output of lspci | grep VGA posted below. 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) The PC only has HDMI and DVI display outputs and using the HDMI output I am only being offered abnormal resolutions. As you can see below it does not even list HDMI1 or DVI1 but just only a fallback. $ export DISPLAY=:0.0 && xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 640 x 480, current 1360 x 768, maximum 1360 x 768 default connected 1360x768+0+0 0mm x 0mm 1360x768 0.0* 1024x768 0.0 800x600 0.0 640x480 0.0 How can I fix this? Does it just need to be configured differently or will I need to use a newer kernel (as Intel Graphics drivers are included in the kernel)? Follow up: kernel to latest Step 1: Go to: http://kernel.ubuntu.com/~kernel-ppa/mainline/ Go to last: http://kernel.ubuntu.com/~kernel-ppa/mainline/v3.6-rc3-quantal/ Download: http://kernel.ubuntu.com/~kernel-ppa/mainline/v3.6-rc3-quantal/linux-headers-3.6.0-030600rc3-generic_3.6.0-030600rc3.201208221735_amd64.deb http://kernel.ubuntu.com/~kernel-ppa/mainline/v3.6-rc3-quantal/linux-headers-3.6.0-030600rc3_3.6.0-030600rc3.201208221735_all.deb http://kernel.ubuntu.com/~kernel-ppa/mainline/v3.6-rc3-quantal/linux-image-3.6.0-030600rc3-generic_3.6.0-030600rc3.201208221735_amd64.deb http://kernel.ubuntu.com/~kernel-ppa/mainline/v3.6-rc3-quantal/linux-image-extra-3.6.0-030600rc3-generic_3.6.0-030600rc3.201208221735_amd64.deb Step 2: sudo dpkg -i linux*.deb Step 3: reboot which shows that i have Ubuntu 12.04 with latest $ uname -a Linux sun-Alienware-X51 3.6.0-030600rc3-generic #201208221735 SMP Wed Aug 22 21:36:32 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux But still same problem remain.

  Read the article

• backlight doesn't work on acer 5732z tried everything I can find

  - by Dude Random21

  Ok if you can solve my problem you're really really good. I want to run ubuntu 12.04 on my acer aspire 5732z I know (from research) that these computer's have issues with the backlight on ubuntu. So I tried a couple of solutions: The "sudo lightdm restart" method. I get no change at all. The "sudo setpci -s 00:02.0 F4.B=30" method. This so far has been the most effective, I first tried it in the F1 console right away I get the screen back, problem is going back to the desktop it goes back to being black. So I tried it from a terminal window and it works as well but as soon as I unplug my external monitor the screen turns black again and doesn't come back. If I plug the monitor back in the screen stays black and the only thing I see is the mouse pointer. From here I go back into console (which I am able to see) and reboot from there. The "sudo sed -i 's/GRUB_CMDLINE_LINUX=""/GRUB_CMDLINE_LINUX="acpi_osi=Linux"/g' /etc/default/grub" method. This one I got no instant change and after reboot still no change. I'm open to pretty much any suggestions you may have.

  Read the article

• Sound card not detected in 13.04

  - by Ganessh Kumar R P

  I have a problem with my sound card. I don't have volume up or down option anywhere. In the setting -> Sound I don't have any card detected. But when I run the command sudo aplay -l, I get the following output **** List of PLAYBACK Hardware Devices **** Failed to create secure directory (/home/ganessh/.config/pulse): Permission denied card 0: MID [HDA Intel MID], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 And the command lspci -v | grep -A7 -i "audio" outputs 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 48 Memory at f0f20000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) (prog-if 00 [Normal decode]) -- 02:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d3efc000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 07:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 So, I assume that the drivers are properly installed but still I don't get any option in the settings or volume control. The same card used to work well back in 2010 versions(04 and 10) Any help is appreciated. Thanks

  Read the article

• Can't install the wireless driver in HP Pavilion dv2419us

  - by maqtanim

  I've just installed Ubuntu 13.04 in an old HP Pavilion dv2419us. The problem is, Ubuntu doesn't detect the wireless card. But it works fine in Windows 7. The following command returns nothing! lspci -vvnn | grep 14e4 And the lspci output is: 00:00.1 RAM memory: NVIDIA Corporation C51 Memory Controller 0 (rev a2) 00:00.2 RAM memory: NVIDIA Corporation C51 Memory Controller 1 (rev a2) 00:00.3 RAM memory: NVIDIA Corporation C51 Memory Controller 5 (rev a2) 00:00.4 RAM memory: NVIDIA Corporation C51 Memory Controller 4 (rev a2) 00:00.5 RAM memory: NVIDIA Corporation C51 Host Bridge (rev a2) 00:00.6 RAM memory: NVIDIA Corporation C51 Memory Controller 3 (rev a2) 00:00.7 RAM memory: NVIDIA Corporation C51 Memory Controller 2 (rev a2) 00:02.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:03.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:05.0 VGA compatible controller: NVIDIA Corporation C51 [GeForce Go 6150] (rev a2) 00:09.0 RAM memory: NVIDIA Corporation MCP51 Host Bridge (rev a2) 00:0a.0 ISA bridge: NVIDIA Corporation MCP51 LPC Bridge (rev a3) 00:0a.1 SMBus: NVIDIA Corporation MCP51 SMBus (rev a3) 00:0a.3 Co-processor: NVIDIA Corporation MCP51 PMU (rev a3) 00:0b.0 USB controller: NVIDIA Corporation MCP51 USB Controller (rev a3) 00:0b.1 USB controller: NVIDIA Corporation MCP51 USB Controller (rev a3) 00:0d.0 IDE interface: NVIDIA Corporation MCP51 IDE (rev f1) 00:0e.0 IDE interface: NVIDIA Corporation MCP51 Serial ATA Controller (rev f1) 00:10.0 PCI bridge: NVIDIA Corporation MCP51 PCI Bridge (rev a2) 00:10.1 Audio device: NVIDIA Corporation MCP51 High Definition Audio (rev a2) 00:14.0 Bridge: NVIDIA Corporation MCP51 Ethernet Controller (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 05:09.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller 05:09.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 05:09.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a) 05:09.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05) The command lspci -nn | grep 0280 gives no output. Any suggestion regarding this?

  Read the article

• Ubuntu 12.04 - default Radeon driver does not work at all

  - by mumble

  I've recently upgraded to 12.04 LTS and I have an ATI Radeon HD5670. I've heard that the open source 'Radeon' driver is used by default. However, it wasn't showing anything for me. What I did was I added the 'nomodeset' option to boot up and install fglrx. But it didn't work well for me as it introduced a lot of problems (freezes/glitches). So I removed/purged fglrx and am planning to use the open source drivers instead. So my question is this: Why is my default Radeon driver not working? Is anyone having a similar issue? I've also tried using the ubuntu-x-swat driver by running the ff commands: sudo add-apt-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update But the result was the same as the Radeon driver. Nothing shows up on system boot. Any ideas? Thanks in advance! Update Running lspci -nn | grep VGA gives me the following: 02:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Redwood [Radeon HD 5670] [1002:68d8]

  Read the article

• VS2012 Coded UI Test closes browser by default

  - by Tarun Arora

  *** Thanks to Steve St. Jean for asking this question and Shubhra Maji for answering this question on the ALM champs list *** 01 – Introduction The default behaviour of coded UI tests running in an Internet Explorer browser has changed between MTM 2010 and MTM 2012. When running a Coded UI test recorded in MTM 2012 or VS 2012 at the end of the test execution the instance of the browser is closed by default. 02 – Description Let’s take an example. As you can see the CloseDinnerNowWeb() method is commented out.  In VS 2010, upon running this test the browser would be left open after the test execution completes. In VS 2012 RTM the behaviour has changed. At the end of the test run, the IE window is closed even though there is no command from the test to do so. In the example below when the test runs, it opens 2 IE windows to the website. When the test run completes both the windows are closed, even though there is no command in the test to close the window. 03 – How to change the CUIT behaviour not to close the IE window after test execution? This change to this functionality in VS 2012 is by design. It is however possible to rollback the behaviour to how it originally was in VS 2010 i.e. the IE window will not close after the test execution unless otherwise commanded by the test to do so. To go back to the original functionality, set BrowserWindow.CloseOnPlaybackCleanup = false More details on the CloseOnPlaybackCleanup property can be found here http://msdn.microsoft.com/en-us/library/microsoft.visualstudio.testtools.uitesting.applicationundertest.closeonplaybackcleanup.aspx  HTH

  Read the article

• Problem with installing Nvidia display drivers on Ubuntu 13.10

  - by Pascal

  Hello everyone and thank you for taking a look at this topic! I'm currently trying out Ubuntu 13.10 but I keep hitting a wall when it comes to installing a driver. I've tried: sudo apt-get install nvidia-current This resulted in a un-bootable system. The screen just stayed black and the cursor displayed as an 'X'. After that I did had to re-install Ubuntu. The computer I'm using is an Acer-Aspire-V3 with a build in Nvidia geforce GT 630M and also with a Intel HD graphics chip-set (not sure if chip-set is the right word here). "lspci | grep VGA" output: pascal@pascal-Aspire-V3-571G:~$ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108M [GeForce GT 630M] (rev a1) I've searched a bit here and there and found out that it would be wise to mention that this laptop is using (or so I think) Nvidia Optimus, not sure if it will add anything to the subject but at least I'll mention it just to be sure. Now to the questions: Q1 How is this caused and how can I fix it? Q2 What additional information could I provide to help you help me?

  Read the article

• Mercurial says "nothing changed", but it did. Sometimes my software is too clever.

  - by user12608033

  It seems I have found a "bug" in Mercurial. It takes a shortcut when checking for differences in tracked files. If the file's size and modification time are unchanged, it assumes its contents are unchanged: $ hg init . $ cp -p .sccs2hg/2005-06-05_00\:00\:00\,nicstat.c nicstat.c $ ls -ogE nicstat.c -rw-r--r-- 1 14722 2012-08-24 11:22:48.819451726 -0700 nicstat.c $ hg add nicstat.c $ hg commit -m "added nicstat.c" $ cp -p .sccs2hg/2005-07-02_00\:00\:00\,nicstat.c nicstat.c $ ls -ogE nicstat.c -rw-r--r-- 1 14722 2012-08-24 11:22:48.819451726 -0700 nicstat.c $ hg diff $ hg commit nothing changed $ touch nicstat.c $ hg diff diff -r b49cf59d431d nicstat.c --- a/nicstat.c Fri Aug 24 11:21:27 2012 -0700 +++ b/nicstat.c Fri Aug 24 11:22:50 2012 -0700 @@ -2,7 +2,7 @@ * nicstat - print network traffic, Kb/s read and written. Solaris 8+. * "netstat -i" only gives a packet count, this program gives Kbytes. * - * 05-Jun-2005, ver 0.81 (check for new versions, http://www.brendangregg.com) + * 02-Jul-2005, ver 0.90 (check for new versions, http://www.brendangregg.com) * [...] Now, before you agree or disagree with me on whether this is a bug, I will also say that I believe it is a feature. Yes, I feel it is an acceptable shortcut because in "real" situations an edit to a file will change the modification time by at least one second (the resolution that hg diff or hg commit is looking for). The benefit of the shortcut is greatly improved performance of operations like "hg diff" and "hg status", particularly where your repository contains a lot of files. Why did I have no change in modification time? Well, my source file was generated by a script that I have written to convert SCCS change history to Mercurial commits. If my script can generate two revisions of a file within a second, and the files are the same size, then I run afoul of this shortcut. Solution - I will just change my script to apply the modification time from the SCCS history to the file prior to commit. A "touch -t " will do that easily.

  Read the article

• Low Graphics and laggy screen after update to 13.10 from 13.04

  - by Wh0RU

  After updating from 13.04 to 13.10 many of 3D unity stuff has stopped working, I am suing Samsung Series 3 (NP350V5X) Laptop which has Switchable Intel and AMD Radeon HD 7670M GFX. xserver-xorg-video-ati does works but NO 3D support and graphics are very low. [I am currently using this] fglrx & fglrx-updates shows blank screen after Login. Intel Graphic Install doesn't work either (dependency error) Output of $ sudo lshw -c video *-display description: VGA compatible controller product: Thames [Radeon HD 7500M/7600M Series] vendor: Advanced Micro Devices, Inc. [AMD/ATI] physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:45 memory:e0000000-efffffff memory:c0120000-c013ffff ioport:3000(size=256) memory:c0100000-c011ffff *-display description: VGA compatible controller product: 3rd Gen Core processor Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:bfc00000-bfffffff memory:d0000000-dfffffff ioport:4000(size=64) Similarly $ /usr/lib/nux/unity_support_test -p OpenGL vendor string: VMware, Inc. OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 3.3, 256 bits) OpenGL version string: 2.1 Mesa 9.2.1 Not software rendered: no Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no Shows no 3D support. Can anyone please guide how to make things working again.

  Read the article

• wireless blocked after installing ubuntu 12.04

  - by Cornelia Frank

  I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• My wireless has suddenly became disabled by hardware switch, BIOS, rfkill, fn+f8 do nothing

  - by cwwk

  I have a toshiba l655d-s5145. There is no physical toggle for the wireless, although the f8 key is supposed to do the trick. It doesn't. The wireless has been working since October, and suddenly, nothing. RFKILL reports that the wireless is hard blocked, but unblock wifi, unblock 0, unblock all do nothing. I inserted a usb dongle, and that is also disabled by hardware switch, although rfkill reports that it is neither hard nor soft blocked. My onboard wireless is 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) according to lspci. Lsmod reports that these drivers are loaded. rtl8192c_common 75767 1 rtl8192ce rtlwifi 110972 1 rtl8192ce I resorted to reformatting the drive and reinstalling, but that also did not work. In BIOS I restored system defaults as there is no specific entry for wifi. Before reinstalling a pure xubuntu I went into Unity and saw that the airplane mode was on and despite being toggled off, it returned to the on position. I'm not sure where to find airplane mode in Xubuntu. What else can I do? I need my wireless.

  Read the article

• Broadcom Wireless Issues in Lubuntu 14.04

  - by ratxinxaxcage67

  I recently installed Lubuntu 14.04 on my parents' old laptop, and I've been having a super difficult time getting the Broadcom card up and running. I've been following this thread: Installing Broadcom Wireless Drivers ...but I'm still stuck. lspci -vnn | grep Network showed: 06:05.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 02) iwconfig showed: lo no wireless extensions. eth0 no wireless extensions. I've installed b43-firmware-installer and b43-fwcutter and also the linux-firmware-nonfree package. At boot, I keep getting a b43-phy0 error, so I tried sudo rmmod b43, and I got: rmmod: ERROR: Module b43 is not currently loaded I also tried: dmesg | grep b43 [ 17.318405] b43legacy-phy0: Broadcom 4306 WLAN found (core revision 4) [ 17.384870] b43legacy-phy0: Loading firmware b43legacy/ucode4.fw [ 18.046777] b43legacy ssb0:0: Direct firmware load failed with error -2 [ 18.046785] b43legacy ssb0:0: Falling back to user helper [ 18.047858] b43legacy-phy0 ERROR: Firmware file "b43legacy/ucode4.fw" not found or load failed. [ 18.047965] b43legacy-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 3). I went to url it told me to, but it didn't tell me to do anything I haven't already tried. Any help and/or suggestions would be greatly appreciated!

  Read the article

• How do I connect to a wireless network?

  - by Keith Groben

  I just installed 10.10 x64 and cannot even find my wireless network let alone connect to it. I've searched all over SE and Ubuntu forums and cannot find out how to do this simple thing. Can some one please give me the answer? It is plugged in right now and is 100% updated. It is a Desktop with wireless card. 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Here's the output: *-network DISABLED description: Wireless interface product: RT2860 vendor: RaLink physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 70:1a:04:f4:de:e9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=2.6.35-27-generic firmware=N/A latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:fcff0000-fcffffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: 00:23:54:fd:c2:32 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.14 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:44 ioport:d800(size=256) memory:fceff000-fcefffff memory:ddffc000-ddffffff memory:fcec0000-fcedffff === Update === I have discovered that this is a know issue with the rt2860. I have been following step by step the instructions found here: http://www.ctbarker.info/2010/05/ubuntu-1004-wireless-chipsets-and-wpa.html I decided to stat over because I was getting stuck on step 5: 'sudo rmmod rt2860sta' is was giving me this problem: 'ERROR: Module rt2860sta does not exist in /proc/modules' Since I started over I cannot even get past step 5 'sudo make' I get this: 'make: * No targets specified and no makefile found. Stop.' I am lost. Any help would be appreciated.

  Read the article

• Ubuntu 13.10, kernel 3.11 blank screen issue with hybrid graphics

  - by Lagerbaer

  On my HP Envy, which has both an Intel on-chip graphics card and an Nvidia Geforce: *-display UNCLAIMED description: 3D controller product: GK208M [GeForce GT 740M] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: cap_list configuration: latency=0 resources: memory:d2000000-d2ffffff memory:a0000000-afffffff memory:b0000000-b1ffffff ioport:5000(size=128) memory:b2000000-b207ffff *-display description: VGA compatible controller product: 4th Gen Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 06 width: 64 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:d3000000-d33fffff memory:c0000000-cfffffff ioport:6000(size=64) I have trouble with all newer kernels. I basically had to install 12.04 LTS and use their 3.5 kernel family to get the system to boot. The 3.8 from 12.10 or the newest 3.11 from Ubuntu 13.10 leave me with a black screen upon boot. On one occasion I did hear the "log in" sound, but the screen did not display anything. I have purged all nvidia drivers so I guess it should just use the intel drivers, but apparently this is all messed up with newer kernel versions. This is different from the other "nvidia boots into blank screen" bug in that I don't rely solely on an nvidia card. Surely the intel on-chip card should be supported and leave me with something different from a blank screen? Again, it only works with kernel versions 3.5.0-41-generic, not with the 3.11.0-12 one that ships with Ubuntu 13.10. When I go into the grub menu and change the boot options from 'quiet splash' to 'nomodeset' I am able to boot the system, but then I don't get any graphics and trying 'sudo service lightdm start' doesn't succeed (I get 100% CPU for apport, but this doesn't do anything either, so I kill it). Help, I'm all out of ideas. EDIT: Let me add that I'm using the EFI boot system and have a dual-boot installation with Windows 8.

  Read the article

< Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >