Search Results

Search found 4343 results on 174 pages for 'verizon wireless'.

Page 55/174 | < Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >

• Meraki wireless access point disconnects clients

  - by resolver101

  We have a Meraki MR16 Cloud Managed AP and it disconnects certain clients. The clients with Intel wireless cards work without any disconnects. The Meraki reports the follow in its event log: Sep 4 09:55:47 WPA authentication Sep 4 09:55:47 802.11 association channel: 11, rssi: 64 Sep 4 09:55:38 802.11 disassociation client has left AP Sep 4 09:55:38 WPA deauthentication vap: 0, radio: 0, aid: 1633956416 An example wireless network card which the Meraki disconnects is Realtek RTL8191SE 802.11b/g/n WiFi Adapter. The realtek laptop is sat 2 meters away from the AP and has a lot of signal and the Meraki reports minimal interference. Any ideas why it disconnects non-intel wireless network cards?

  Read the article

• How to bridge multiple wireless access points (and internet entry points) into one network

  - by amccormack

  I have two DSL lines coming in to wireless access points and then running to a RV082 Gateway/Bridge. The gateway then runs to a switch, which runs to multiple PCs and a Printer (See picture below). Normally, I would set up the wireless access points behind the gateway, but they are also the modems for the dsl. I have found that I can not print to the network printer if I am connected to the wireless network, but only if I am connected to the wired network. How can I configure the Gateway and APs (Routers) so that the PCs and Printer are all on the same internal network? I have tried turning DHCP off or redirect on the APs and redirect them to the Gateway. However, neither of these worked. Furthermore, I tried pinging the Gateway from the AP but got no response.

  Read the article

• How to go about scheduling a task in windows 7 to change wireless connection

  - by Skindeep2366

  This may or not be something that can be done. I cannot find anything on the wireless connection manager built into windows 7 let alone methods for passing params into it. Problem is as follows: I have 2 wireless routers. One provides internet access, the other provides sole access to the local network. Every day at 4am the main system creates a backup in 2 locations. One is a External usb drive, the other is a location on the network. This is all cool if it is remembered to change over to the local network router before leaving. But if it is forgotten the roof will collapse, the walls will burn, and I will be... well you get the idea. Solution: there is already a custom event that fires a automated backup program at 4am everyday. I need someway to force the wireless network to use the correct connection at say 3:58am everyday. Any ideas????

  Read the article

• Ubuntu problem not connecting to wireless or wired network

  - by ToughPal

  I recently installed openvpn and things were working. But I got a weird screen after a few hours and on restart my wired and wireless connections are not working. Can someone help? cat /etc/network/interfaces auto lo iface lo inet loopback cat /etc/resolv.conf #Generated by NetworkManager Is there anything missing? I tried both wired and wireless and both are not working. Usually if I ever have a problem with wireless, the wired always work! My /etc/network/interfaces is looking wrong. Can you please send me yours? I am using ubuntu 9.10 and the internet was working correctly until today! Please help

  Read the article

• Enable/disable wireless interface in a bat file

  - by Herms

  Is there a way to enable/disable a wireless network interface via the command line (so I can put it in a bat file)? When I'm in the office I use a wired connection, but Windows still occasionally bugs me about my wireless connection not being connected (even though I turned off the option for notifying me when there's no connectivity). I'm guessing the only way to stop it from bugging me is to disable the interface, but I'd rather not have to go into the network settings every time I need to do so. I'd like to set up a bat file or a shortcut that I can use to enable/disable the wireless (preferably a single one that toggles the current state), and then just set up a keyboard shortcut for that. I just have no idea how to do so from the command line.

  Read the article

• Cannot install wireless lan service on windows 2012 RTM offline

  - by user1763118

  I'm having trouble installing the wireless lan service offline with a fresh installed windows 2012 server RTM. I tried "install-windowsfeature wireless-networking" in the non-gui mode and using the server manager in the gui mode to enable the wireless lan service, but both of them show a "failure configuring windows updates" message after the installation restarted the system. I checked the event log and I think messages about "The WLAN Autoconfig service depends on the following service: nativewifip. This service might not be installed" are the source of the issue. Google shows it is a service called "native wifi filter", but I cannot find anywhere to install that service. I don't have a Ethernet adapter for that computer, so have to install everything offline before the wifi's working.

  Read the article

• Determining Maximum Txpower a WiFi Card Supports?

  - by BigGenius

  I have a Atheros R9285 wifi card. How can i determine , what is max. Txpower it can support? biggenius@hackbook:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Default" Mode:Managed Frequency:2.437 GHz Access Point: 00:08:5C:9D:4F:40 Bit Rate=2 Mb/s Tx-Power=35 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=24/70 Signal level=-86 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:140 Invalid misc:247 Missed beacon:0 eth0 no wireless extensions. biggenius@hackbook:~$ iw phy0 info Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (35.0 dBm) * 2417 MHz [2] (35.0 dBm) * 2422 MHz [3] (35.0 dBm) * 2427 MHz [4] (35.0 dBm) * 2432 MHz [5] (35.0 dBm) * 2437 MHz [6] (35.0 dBm) * 2442 MHz [7] (35.0 dBm) * 2447 MHz [8] (35.0 dBm) * 2452 MHz [9] (35.0 dBm) * 2457 MHz [10] (35.0 dBm) * 2462 MHz [11] (35.0 dBm) * 2467 MHz [12] (35.0 dBm) * 2472 MHz [13] (35.0 dBm) * 2484 MHz [14] (35.0 dBm) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Band 2: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 5180 MHz [36] (35.0 dBm) * 5200 MHz [40] (35.0 dBm) * 5220 MHz [44] (35.0 dBm) * 5240 MHz [48] (35.0 dBm) * 5260 MHz [52] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5280 MHz [56] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5300 MHz [60] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5320 MHz [64] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5500 MHz [100] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5520 MHz [104] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5540 MHz [108] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5560 MHz [112] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5580 MHz [116] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5600 MHz [120] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5620 MHz [124] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5640 MHz [128] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5660 MHz [132] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5680 MHz [136] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5700 MHz [140] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5745 MHz [149] (35.0 dBm) * 5765 MHz [153] (35.0 dBm) * 5785 MHz [157] (35.0 dBm) * 5805 MHz [161] (35.0 dBm) * 5825 MHz [165] (35.0 dBm) Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ managed, WDS, P2P-client } <= 2048, #{ AP, mesh point, P2P-GO } <= 8, total <= 2048, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (82) * Unknown command (81) * Unknown command (84) * Unknown command (87) * Unknown command (85) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS.

  Read the article

• Dell 3721 Wifi problem Ubuntu 13.04

  - by Sebastian

  I have a Dell 3721 which comes original with windows 8. I managed it to install ubuntu 12.10 on this laptop, even there was no out of the box drivers. With 12.10 I was forces to install this .deb package couple of times. After installing it, it was ok for some weeks before I have to install it again. Maybe some security updates destroy something which made in necessary to install it again... http://jas.gemnetworks.com/debian/pool/main/w/wireless-bcm43142/wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb My problem is, that this package isnt working with ubuntu 13.04 anymore. So I cant use Wifi now. Also my display is almost dark, I cant change the brightness level with ubuntu 13.04. Hope you can give me some advice. Dell:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation 3rd Gen Core processor DRAM Controller [8086:0154] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) 00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) 00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) 00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) 00:1c.1 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 [8086:1e12] (rev c4) 00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) 00:1f.0 ISA bridge [0601]: Intel Corporation HM76 Express Chipset LPC Controller [8086:1e59] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) 00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04) 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 02:00.0 Network controller [0280]: Broadcom Corporation BCM43142 802.11b/g/n [14e4:4365] (rev 01) @Dell:~$ lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0a5c:21d7 Broadcom Corp. Bus 001 Device 004: ID 0bda:0129 Realtek Semiconductor Corp. Bus 001 Device 005: ID 0c45:64ad Microdia @Dell:~$ lspci -nn | grep VGA 00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) @Dell:~$ sudo lshw -class network *-network Beschreibung: Ethernet interface Produkt: RTL8101E/RTL8102E PCI Express Fast Ethernet controller Hersteller: Realtek Semiconductor Co., Ltd. Physische ID: 0 Bus-Informationen: pci@0000:01:00.0 Logischer Name: eth0 Version: 05 Seriennummer: xx:xx:xx:xx:xx:xx Größe: 100Mbit/s Kapazität: 100Mbit/s Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation Konfiguration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.103 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s Ressourcen: irq:42 ioport:2000(Größe=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network UNGEFORDERT Beschreibung: Network controller Produkt: BCM43142 802.11b/g/n Hersteller: Broadcom Corporation Physische ID: 0 Bus-Informationen: pci@0000:02:00.0 Version: 01 Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress bus_master cap_list Konfiguration: latency=0 Ressourcen: memory:c0500000-c0507fff

  Read the article

• Wifi Direct P2P-go and P2P-client support in ubuntu

  - by giri

  I am trying to get wifi direct working on a laptop with ubuntu 12.04 When I type the command 'iw list' it doesn't show P2P-client or P2P-go under 'supported interface modes.From http://wireless.kernel.org/en/users/Documentation/iw/replace-iwconfig I found that 'iwconfig' was replaced with 'iw'.Does it mean that my hardware doesn't have support for wifi-direct or is it just the software(drivers) issue? If is it just sofware issue please help me to find the right drivers which support wifi-direct. Here is the info about my ethernet controller from the output of 'lspci' 02:00.0 Ethernet controller: Atheros Communication Inc. AR242x / AR542x Wreless Network Adapter (PCI-Express) (rev 01) 06:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8055 PCI-E Gigabit Ethernet Controller (rev 13)

  Read the article

• How can I get a Belkin N600 DB (F9L1101v1) to work on Ubuntu 12,04 64-Bit

  - by rheide

  I could use some assistance to trying to get a Belkin N600 DB Wireless Dual-Band USB Adapter to work on a Dell Inspiron 1525 with 64-Bit Ubuntu 12.04. The device won't work out of the box. Tried to go the NDISWrapper route, but using the GUI, received the following message: Module could not be loaded. Error was: FATAL: Module ndiswrapper not found. Is the ndiswrapper module installed? Despite the fact that it showed up listed in the GUI, the device still did not function properly. How should I proceed from here?

  Read the article

• wpa_supplicant ioctl[SIOCSIWENCODEEXT]: Invalid argument

  - by RobinJ

  I just installed Ubuntu Server on a spare computer with a broken graphic card, and I needed to setup my wifi. I thought No problem, I've done it before from the command line, in Arch Linux., only the steps I had to take in Arch Linux didn't work in Ubuntu Server (that's odd, wasn't Ubuntu supposed to be so much more user-friendly? :/). This is what I'd normally do: ip link set wlan0 up wpa_passphrase <ESSID> <WPA KEY> > /etc/wpa_supplicant.conf wpa_supplicant -B -Dwext -i wlan0 -c /etc/wpa_supplicant.conf dhcpcd wlan0 Only at the wpa_supplicant I get some strane message: ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument And if I try to run dhcpcd then (which I manually installed, as it didn't come preinstalled with Ubuntu Server), it times out. Help on how to do it would be much appreciated. My wireless driver is iwl3945.

  Read the article

• How to set wifi driver settings to prefer 5 GHz channel above 2.4 GHz

  - by Wouter

  Currently I'm in a new building of my university. In this building my wifi often breaks down and then restores connection again. This is really irritating since it happens a lot. Now as a coincidence there were some tech guys running around here and where asking everyone if the wifi was doing fine. I told them that my wifi tears down all the time and then reconnects. They figured out that my wifi is switching all the time between the 2.4 GHz channel and 5 GHz channel. They asked me if I could acces the driver settings of my wireless card. Unfortunately I don't know how to do this is in either Linux or Windows. And unfortunately again they only knew the windows solution xD. So I hope somebody can tell me how I tell my wifi that it should stay on the 5 GHz network and not disconnect and switch to the 2.4 GHz channel?

  Read the article

• help w/ macbook & latest ubuntu

  - by dirtyglove

  what is the latest version of ubuntu i can run w/ WORKING wifi on my macbook 4,1(early 2008)? i dual booted my mac os x lion alongside 12.10 ubuntu but cant figure how to get the wireless to work? so i downgraded to 10.10 for now.. is 10.10 the latest version i can have on my macbook with working wifi? or is there another? or am i just missing a noobish terminal code to fix the drivers? help appreciated! thanks

  Read the article

• Two Wifi Icons in Panel [Solved]

  - by Alex

  I have the exact problem in 13.10 as this user Two Wifi indicators in panel. Here are some screenshots: Here are some screenshots from another user: http://ubuntuforums.org/showthread.php?t=2183020&p=12825563 ifconfig and iwconfig outputs $ ifconfig lo Link encap:Local Loopback inet addr:XXXXXX Mask:XXXXXXX inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2243 errors:0 dropped:0 overruns:0 frame:0 TX packets:2243 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:209889 (209.8 KB) TX bytes:209889 (209.8 KB) wlan0 Link encap:Ethernet HWaddr XXXXXXXXX inet addr:XXXXXX Bcast:XXXXXXXX Mask:XXXXXXX inet6 addr: XXXXXXX Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5925 errors:0 dropped:0 overruns:0 frame:0 TX packets:3361 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2951818 (2.9 MB) TX bytes:630579 (630.5 KB) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"XXXXX" Mode:Managed Frequency:2.437 GHz Access Point: XXXXXXXX Bit Rate=72.2 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:153 Invalid misc:472 Missed beacon:0

  Read the article

• No Internet On 12.04.1

  - by David Ramos

  I have no internet on Ubuntu 12.04.1 so i'm on a desktop so I got to install a .exe program to run my wireless card for my desktop so I got internet access, But I can't seem to download wine or its source files. If I do I put on my usb and boot into Ubuntu but then when I try to open it I get the programs source files etc. Anyone who could help me Please do :| ( I can't install wine from software center since I have no connection online). Note : I can download my stuff on windows 8 boot so I can transfer files to my usb to run on Ubuntu.

  Read the article

• Wifi works but doesn't start automatically on ubuntu 11.10

  - by Nikita Kononov

  Good evening everyone, I have got an issue which I hope you will help me to solve. I was trying to update my Kernel in ubuntu from this web-site http://kernel.ubuntu.com/~kernel-ppa/mainline/v3.2-rc4-oneiric/ And everything went smooth. But, for some reason, my wifi doesn't work in new Kernel so I decided to switch back to my old one 3.0.0-17 generic and to my surprise WIFI doesn't start automatically eventhou it was working. What I mean is that I have to click on wifi icon and put a mark Enable Wireless. This is not a really serious issue but I don't like switch on everytime at log in my WIFI because before that it was working when system started. What is the cause of this and how to fix it. Thank you very much for you help.

  Read the article

• How do I ban a wifi network in Network Manager?

  - by Chris Conway

  My wifi connection drops sometimes and, for some reason, Network Manager attempts to connect to my neighbor's network, which requires a password that I don't know. The network in question is not listed in the "Edit Connections..." dialog and I can find no reference to it in any configuration file, but still the password dialog pops up every time my main connection drops. Is there a way to blacklist a wireless network so that the Network Manager will never attempt to connect to it? Or, equivalently, how can I remove the configuration data that causes the Network Manager to attempt to connect to this particular network?

  Read the article

• Broadcom STA driver doesn't work well with BCM4313

  - by Oli

  Following on from my other question about our new Samsung Q330, I've noticed that the wireless is incredibly flakey. It can connect but after a little use, especially if it does a lot of downloading at once (read: install something from the Software Centre), the connection stops working. Network Manager still see the connection, there's just no network throughput. I've simple tests like pinging other local network hosts and they just fail. The Samsung Q330 has a Broadcom BCM4313 wifi card (it's proper ID: 14e4:4727) and it's running on the Broadcom STA drivers that Jockey suggests (it didn't work at all without this). I did try installing b43-fwcutter but this just didn't do anything. I was expecting a configuration screen to come up (to select a firmware) but it never did. This page suggests the newer brcm80211 driver might be able to help, but I don't know how to install that. If you think this is the right route, please let me know how one goes about installing it.

  Read the article

• Network Manager kicks off abruptly

  - by Vijay Selvaraj

  I have installed Ubuntu 10.10 and trying to connect with my ADSL Wireless broadband internet modem using Linksys WUSB600N receiver. The good news is the OS is able to detect my wifi network and I am able to hook to network over WPA authentication with basic settings. But the network goes off abruptly and never connects again until I reboot the machine. I have Windows 7 as dual boot on my machine. The same adapter works perfectly with Windows 7 but not in Ubuntu. Is there anything in need to tweak to make things working or do I need to try any other better network manager on Ubuntu?

  Read the article

• Cannot connect to a Wifi network chipset AR9287

  - by Fritz

  After updating my newly installed ubuntu 10.10. I can't connect to the wifi network anymore although it is showing it. Tried to install manufacturer driver INF file via ndiswrapper only makes things worst - lost my wifi. Downloaded and installed the compat-wireless driver for the Atheros AR9287. After installing, i got my wifi connection again but after rebooting I can't reconnect again. The Wifi access point is showing 2/5 to 3/5 signal strength. Laptop: Acer Aspire 4741G Wifi Adapter: Atheros AR9287 OS: Ubuntu 10.10 64bit

  Read the article

• Acer Aspire One 722 broadcom 4313 wifi

  - by Colin Matheson

  I had an Acer Aspire One 722 with the Atheros Wifi card and it worked fine on 11.04. So we bought 200 of them for our school. However these all came with the Broadcom BCM4313 wireless card and there are issues. It is using the brcmsmac driver and they connect initially. However after a time (sometimes just a few webpages) some of them lose connection. However, they still have an IP and network-manager says they are connected, but no pages load and you can't ping anything on the LAN or internet. A disconnect/reconnect can fix it, but sometimes a restart is required. It happens frequently so is a major issue. Lots of broadcom drivers are blacklisted: bcm43xx, b43, brcm80211. Any ideas or experiences with the broadcom4313 card? Please save these computers from a Windows fate!

  Read the article

• WiFi and Bluetooth will not work on Dell Studio XPS 1645

  - by Ross

  Today I acquired a Dell XPS 1645. Ubuntu seems to run alright on it however The bluetooth is not detected and the WiFi doesn't work. The WiFi is especially weird because I actually have the restricted driver enabled for it. It also worked for a short while when I first booted into Ubuntu however now there isn't even an option to enable wireless. If anyone could possibly help me out with this I'd deeply appreciate it. I've not had to return to Windows for a good while and it's not something I want to have to do now.

  Read the article

• Unable to use TL-WN821N

  - by udiw

  Hi, I got a TP-LINK USB wireless module - TL-WN821N, using Ubuntu 10.4 (same problems were also seen in 10.10). From everything I've read online, the usb should work just fine, since the Atheros ar9170 is built into the kernel. However, when I plug it in, it is detected as a USB device, but there is no wlan associated with it, and basically - nothing happens. Am I doing something wrong? what should I do so that the Atheros driver is associated with this device? btw, on Windows it works fine (with the drivers). Some logs: $ uname -mr 2.6.32-28-generic i686 $ lsb_release -d Description: Ubuntu 10.04.2 LTS $ lsusb ... (trimmed) Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 017: ID 0cf3:7015 Atheros Communications, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub $ lsmod |grep ar9 ar9170usb 51296 0 ath 7611 1 ar9170usb mac80211 205402 3 ar9170usb,iwl3945,iwlcore cfg80211 126528 5 ar9170usb,ath,iwl3945,iwlcore,mac80211 led_class 2864 4 ar9170usb,iwl3945,iwlcore,sdhci

  Read the article

• Updated 11.10 - now trackpad and wifi won't work. How can these be fixed?

  - by Aron Standley

  I reinstalled 11.10 on my Asus EEE 1005HA, and my mousepad hasn't been working since. I've tried the workarounds mentioned in this post: http://ubuntuforums.org/showthread.php?t=1867357 but, I get the message on the command line that says, "Synaptic isn't installed." When I go to the network settings to install Synaptic, I can't turn on wifi - no wireless options exist. How can I turn on wifi from the command line, on a new 11.10 install? Or, is there a way to turn on the trackpad and wifi from the install thumb drive? How can I move forward?

  Read the article

• Need instructions how to create wpa_supplicant.conf and add fast_reauth=0 to it // WPA 2 Enterprise & frequent wlan disconnects

  - by nutty about natty

  Like many other natty users on a university / academic network, I'm experiencing annoying frequent disconnects / hangs / delays. See, for instance: https://bugs.launchpad.net/ubuntu/+source/wpasupplicant/+bug/429370 I would like to learn how to add fast_reauth=0 to the wpa_supplicant.conf file. This file, it seems, does not exit by default, and needs to be manually created first: http://w1.fi/gitweb/gitweb.cgi?p=hostap.git;a=blob_plain;f=wpa_supplicant/README [quote] You will need to make a configuration file, e.g., /etc/wpa_supplicant.conf, with network configuration for the networks you are going to use. [unquote] Further, I installed wpa_gui which probably needs to be launched with parameters, else it's pretty blank... What I'm hoping for is this: That creating a wpa_supplicant.conf file with fast_reauth=0 in it, saving it to the relevant path, will work and make my uni wireless (more or even completely) stable. I read mixed reviews about wicd (as an alternative to the network manager). Also note that on my basic wlan at home (with bog-standard wpa encryption) the connection is stable. Thanks!

  Read the article

< Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >