Search Results

Search found 3593 results on 144 pages for 'wake on lan'.

Page 55/144 | < Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >

  • Webmin ADSL module

    - by expatcm
    I was wondering if the Webmin ADSL module is going to help me solve a problem .... but I cannot find any documentation telling me what the module does ..... Any ideas? What I am hoping is that it will solve a problem .... I am just in the process of setting up a Debian server. I will use the DHCP server as part of the Debian setup to manage the lan IP addresses. I want to turn off the external DHCP server which is part of the Linksys ADSL modem / router and use just the modem. The challenge I have is knowing what I need to do in order to get the public DNS on the eth1. When I turn off the DHCP on the modem / router not a lot happens apart from no longer being able to access the settings .......... So I am looking at this Webmin module and wondering if it is to manage the ADSL connection and find the public DNS address .... The local DHCP server is working well for the lan, I am just stuck for the external DNS.

    Read the article

  • Slow network file transfer (under 20KB/s) on newly built x64 Win7

    - by Mangoshake
    I am getting <20KB/s for local network file transfer. If I transfer a very small file (less than 100KB) it would start quickly then slow down to <20KB/s. all subsequently network file transfer would be slow, a reboot is needed to reset this. If I transfer a large file it would be stuck on calculating for a long time and then begin with <20KB/s immediately. This is a newly built desktop running Windows 7 x64 SP1. Realtek gigabit LAN from the motherboard (ASRock Extreme3 gen3). Problematic speed is observed on the private LAN, both through ethernet and WiFi. The Router is D-Link DIR-655. Remote Differential Compression is off. Drivers are up-to-date from ASRock's website. I have tested network file transfer to and from another Windows 7 laptop and a MacBook Pro, so I am fairly certain it is the desktop's problem. The slow speed only happens with one direction also, outbound from the desktop, regardless of whether I initiate the file transfer action from the origin or the destination. Inbound network file transfer and internet speeds are fine, so I don't think this is a hardware issue. I am getting 74.8MB/s internet upload speed from speedtest.net (http://www.speedtest.net/result/1852752479.png). Inbound network file transfer I can get around 10-15MB/s. I am hoping this community has some insight for me to troubleshoot this. I don't see anything obviously related from the Event Viewer, and beyond that I just don't know where else to look. Any suggestions are greatly appreciated, thank you in advance.

    Read the article

  • postfix smtpd rejecting mail from outside network match_list_match: no match

    - by Loopo
    My postfix (V: 2.5.5-1.1) running on ubuntu server (9.04) started to reject mail arriving in from outside about 2 weeks ago. Doing a "manual" session via telnet shows that the connection is always closed after the MAIL FROM: [email protected] line is input, with the message "Connection closed by foreign host." Doing the same from another client inside the LAN works fine. In the log files I get the line "lost connection after MAIL from xxxxx.tld[xxx.xxx.xxx.xxx]" This is after some lines like: match_hostaddr: XXX.XXX.XXX.XXX ~? [::1]/128 match_hostname: XXXX.tld ~? 192.168.1.0/24 ... match_list_match: xxx.xxx.xxx.xxx: no match which seem to suggest some kind of filter which checks for allowed addresses. I have been unable to locate where this filter lives, or how to turn it off. I'm not even sure if that's what's causing my problem. Connections from inside the LAN don't get disconnected even though they also show a "match_list_match: ... no match" line. I didn't change any configuration files recently, below is my main.cf as it currently stands. I don't really know what all the parameters do and how they interact. I just set it up initially and it worked fine (up to recently). smtpd_banner = $myhostname ESMTP $mail_name (GNU) biff = no readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/server.crt smtpd_tls_key_file=/etc/ssl/private/server.key #smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_sasl_auth_enable = no smtp_use_tls=no smtp_sasl_password_maps = hash:/etc/postfix/smtp_auth myhostname = XXXXXXX.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = XXXX.XXXX.com, XXXX.com, localhost.XXXXX.com, localhost relayhost = XXX.XXX.XXX.XXX mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 192.168.1.0/24 mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all smtpd_sasl_local_domain = #smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous smtpd_sasl_authenticated_header = yes broken_sasl_auth_clients = yes smtpd_recipient_restrictions = permit_mynetworks,permit_sasl_authenticated,reject_unauth_ when checking the process list, postfix/smtpd runs as smtpd -n smtp -t inet -u -c -o stress -v -v Any clues?

    Read the article

  • How to get a new-pssession in PowerShell to talk to my ICS-connected laptop for Remoting

    - by Scott Bilas
    If I have my laptop on the LAN, then Powershell remoting works fine from my workstation to the laptop. However, the LAN is wireless, and so sometimes I will connect on a wire to my workstation. It has two ethernet ports so I have the secondary wired up to share to the laptop using Win7's Internet Connection Sharing. (Btw I know that avoiding ICS would solve the problem, but that's not an option right now.) So my question is: what magic registry bits or command line options do I need to flip to get remoting to work to my laptop through ICS? Here's what happens when I try it: new-pssession -computername 192.168.137.161 [192.168.137.161] Connecting to remote server failed with the following error message : The WinRM client cannot process the request. Default authentication may be used with an IP address under the following conditions: the transport is HTTPS or the destination is in the TrustedHosts list, and explicit credentials are provided. Use winrm.cmd to configure TrustedHosts. Note that computers in the TrustedHosts list might not be authenticated. For more information on how to set TrustedHosts run the following command: winrm help config. For more information, see the about_Remote_Troubleshooting Help topic. + CategoryInfo : OpenError: (System.Manageme....RemoteRunspace:RemoteRunspace) [], PSRemotingTransportException + FullyQualifiedErrorId : PSSessionOpenFailed I'm having a hard time understanding the documentation for PowerShell and WinRM. I've tried messing with allowing ports in the firewall and setting TrustedHosts to * on my workstation (don't think this is a good idea on the laptop). I have no idea where to go from here, would appreciate any help.

    Read the article

  • Optimal Networking Setup for a 2-Story unit?

    - by user29336
    I am moving into a 4 bedroom two-story unit. It’s roughly 2,200 sq ft. I want absolute max throughput possible to be achieved in all focal points. We’re all in internet related industries. Between gaming and web-development latency and throughput are major factors for us. Here’s our main focal points: 1) Garage (office). downstairs 2) Each bedroom x4. upstairs 3) Living room. downstairs The fastest line we can get is Comcast 50mbdown/5up (Wideband). I am looking for the best way to achieve wireless and wired performance for our setup. Our gaming computers may be in our bedroom, and we also may bring it down to the office every now and then for “LAN” sessions. Most wireless will be happening downstairs with our laptops, but since we may do LAN sessions then hard wired latency may be important there too. My concerns: If we do only wireless there would be too much latency for gaming. I don’t know if placing one D-link DGL 4500 on the top floor would be enough; which I currently own. (http://dlink.com/us/en/home-solutions/support/product/dgl-4500-xtreme-n-gaming-router) As far as I’m aware wireless signals transfer best top down. Would this wireless router be enough on top floor and that’s it? My second strategy was a combination of wiring and wireless but I’m not sure what’s easiest way to do this? This is a place we’re renting, so I’m not sure how much leeway we have with wiring, but we’re all pretty competent... if we can’t drill through a wall we can probably “stitch” them across the edges wherever needed. Thoughts on the optimal way to do this?

    Read the article

  • Iptables Forwarding problem

    - by ankit
    Hi all, I had initally asked question about sertting up my linux box for natting for my home network and was given suggestions in the thread here. Did not want to clutter the old question so starting a new one here. based on the earlier suggestions, i have come up with the following rules ... :PREROUTING ACCEPT [1:48] :OUTPUT ACCEPT [12:860] :POSTROUTING ACCEPT [3:228] -A POSTROUTING -o eth0 -j MASQUERADE COMMIT *filter :INPUT DROP [3:228] :FORWARD DROP [0:0] :OUTPUT DROP [0:0] -A INPUT -i lo -j ACCEPT -A INPUT -i eth0 -p icmp -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 443 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 22 -j ACCEPT -A FORWARD -i eth1 -p icmp -j ACCEPT -A FORWARD -i eth1 -p tcp -m tcp --dport 80 -j ACCEPT -A FORWARD -i eth1 -p tcp -m tcp --dport 443 -j ACCEPT -A OUTPUT -p icmp -j ACCEPT -A OUTPUT -j ACCEPT COMMIT If you notice, i do have the proper MASQURADING rule and the proper FORWARD filter rule as well. However i am facing 2 problems On the linux box itself DNS resolving is not working the lan clients connected to the linux box, are still not able to get to internet. when i ping something from them, i see the DROP count in iptables INPUT rule increasing. now my question is, when i am pinging something from the lan client, how come it is being matched by the input chain ?! should it be in the forward chain ? Chain INPUT (policy DROP 20 packets, 2314 bytes) pkts bytes target prot opt in out source destination 99 9891 ACCEPT all -- lo any anywhere anywhere 0 0 ACCEPT icmp -- eth0 any anywhere anywhere 0 0 ACCEPT tcp -- eth0 any anywhere anywhere tcp dpt:http 0 0 ACCEPT tcp -- eth0 any anywhere anywhere tcp dpt:https 122 9092 ACCEPT tcp -- eth0 any anywhere anywhere tcp dpt:ssh Thanks ankit

    Read the article

  • Suggestions for accessing SQL Server from internet

    - by Ian Boyd
    i need to be able to access a customer's SQL Server, and ideally their entire LAN, remotely. They have a firewall/router, but the guy responsible for it is unwilling to open ports for SQL Server, and is unable to support PPTP forwarding. The admin did open VNC, on a non-stanrdard port, but since they have a dynamic IP it is difficult to find them all the time. In the past i have created a VPN connection that connects back to our network. But that didn't work so well, since when i need access i have to ask the computer-phobic users to double-click the icon and press Connect i did try creating a scheduled task that attempts to keep the VPN connection back to our office up at all times by running: >rasdial "vpn to me" But after a few months the VPN connection went insane, and thought it was both, and neither, connected an disconnected; and the vpn connection wouldn't work again until the server was rebooted. Can anyone think of a way where i can access the customer's LAN that doesn't involve opening ports on the router needing to know their external IP customer interaction of any kind Blah blah blah use vpn vnc protocol has known weaknesses you are unwise to lower your defenses it's not wise to expose SQL Server directly to the internet you stole that line from Empire Customer doesn't care about any of that. Customer wants things to work.

    Read the article

  • How can I set up a local nameserver and modify DNS zones on it?

    - by Joe Hopfgartner
    This is a follow up to this question. I am having an issue with a Router that doesn't support hairpinning properly. See the link above for details. Now I want to set up a local DNS server that Hosts in our LAN can use to resolve public Hostnames (usual webbrowsing... ). Additionally I want to modify certain zones. In our LAN we have some servers serving resources that are not available in our public dns zone. We always have to configure our local LMHost files accordingly. For example we have a staging installation with a new feature running on a local Webserver, and we cannot access it with the IP directly because the website runs in a named virtual host container, we have to configure LMHost file to point some domain to the local IP address. And now we have also the Hair pinning issue. So my question is: What software can I use? Will bind do the job? I just need to insert some A entries into the zone. As easy as possible. We have local Linux/Ubuntu servers.

    Read the article

  • Firewall for internal networks

    - by Cylindric
    I have a virtualised infrastructure here, with separated networks (some physically, some just by VLAN) for iSCSI traffic, VMware management traffic, production traffic, etc. The recommendations are of course to not allow access from the LAN to the iSCSI network for example, for obvious security and performance reasons, and same between DMZ/LAN, etc. The problem I have is that in reality, some services do need access across the networks from time to time: System monitoring server needs to see the ESX hosts and the SAN for SNMP VSphere guest console access needs direct access to the ESX host the VM is running on VMware Converter wants access to the ESX host the VM will be created on The SAN email notification system wants access to our mail server Rather than wildly opening up the entire network, I'd like to place a firewall spanning these networks, so I can allow just the access required For example: SAN SMTP Server for email Management SAN for monitoring via SNMP Management ESX for monitoring via SNMP Target Server ESX for VMConverter Can someone recommend a free firewall that will allow this kind of thing without too much low-level tinkering of config files? I've used products such as IPcop before, and it seems to be possible to achieve this using that product if I re-purpose their ideas of "WAN", "WLAN" (the red/green/orange/blue interfaces), but was wondering if there were any other accepted products for this sort of thing. Thanks.

    Read the article

  • Using Round Robin DNS on simple VPN setup

    - by dannymcc
    We have two internet connections which are load balanced to share the load between the two. We set this up after one of the internet provider proved to be less than reliable but great speed and latency wise when it is working. We'd rather utilise both connections as much as possible rather than leave one idle until the other drops out. We have a number of remote workers who occasionally need to connect via VPN from their laptops or iPads, we also have a small number of permanent LAN to LAN tunnels running from smaller branches. Originally we only had one internet connection and used one of our static IP addresses for all VPN users. Now that we have two internet connections running all of the time I am trying to make sure that the VPN is available to our team regardless of which connection drops. So my solution is to create two A records for our domain name with a value of vpn. and the two static IP addresses from each peer. Is this a sensible way of achieving this? Should I expect higher latency due to packets being lost if one peer fails and some packets still get routed to it anyway? A brief mockup of the setup I have:

    Read the article

  • Cisco ASA 8.2 ACL For NAT

    - by javano
    Sadly I have gone back in time to ASA 8.2(5)33 which I am not so familiar with. I have configured NAT between two interfaces but traffic isn't passing becasue I can't get the ACL to work; (The full config which isn't very big is here but to keep this post tidy I have just pasted the important parts below); interface Ethernet0/0 switchport access vlan 108 ! interface Ethernet0/6 switchport access vlan 104 ! interface Ethernet0/7 switchport access vlan 105 ! interface Vlan104 description BUILDING2 nameif BUILDING2 security-level 0 ip address 10.104.0.1 255.255.255.0 ! interface Vlan105 description BUILDING1 nameif BUILDING1 security-level 0 ip address 10.105.0.1 255.255.255.0 ! interface Vlan108 description Main LAN VLAN nameif lan security-level 0 ip address 172.22.0.215 255.255.255.0 ! object-group network obj_net_Remote_Hosts network-object host 111.111.111.3 network-object host 111.111.111.65 object-group network obj_host_pc1_eth1 network-object host 10.104.0.111 object-group network obj_host_pc2_eth1 network-object host 10.104.0.112 object-group network obj_host_pc3_eth1 network-object host 10.104.0.106 object-group network obj_host_pc4_eth1 network-object host 10.104.0.107 object-group network obj_net_PCs description IPs of PCs group-object obj_host_pc1_eth1 group-object obj_host_pc2_eth1 group-object obj_host_pc3_eth1 group-object obj_host_pc4_eth1 access-list acl_NAT_pc1_91 extended permit tcp host 10.104.0.111 host 111.111.111.3 eq 8101 access-list acl_Permit_PCs extended permit tcp object-group obj_net_PCs object-group obj_net_Remote_Hosts eq 8101 ! global (BUILDING1) 11 111.111.222.91 netmask 255.255.255.255 nat (BUILDING2) 11 access-list acl_NAT_pc1_91 access-group acl_Permit_PCs in interface BUILDING2 route BUILDING1 111.111.111.3 255.255.255.255 10.105.0.2 1 route BUILDING1 111.111.111.65 255.255.255.255 10.105.0.2 1 When I try and connect from PC1 to ip 111.111.111.3 I see the following error logged on the ASA console; %ASA-2-106001: Inbound TCP connection denied from 10.104.0.111/38495 to 111.111.111.3/8101 flags SYN on interface blades What the duce!

    Read the article

  • Tips and Suggestions IP Address Re-Addressing?

    - by RSXAdmin
    Hello serverfault Universe, My ever evolving and expanding local area network is currently using a class-C address. My network consists of multiple subnets depending on site/location. 192.168.1.x is site HQ 192.168.5.x is secondary site 192.168.10.x is so on and so forth. Long story short - I have inherited this network design from the previous admin who has left the company which started off with a dozen people and now has just over 300 full time/part time employees. We do not yet have client VPN access; but we do have site to site VPN setup. My question is, in preparation for outside client access to my network via Cisco ASA, I would like to re-address the HQ site because I understand a 192.168.1.x or 192.168.0.x are not very good choices for a company subnet - it may conflict with a home user's LAN when connecting to my LAN, I believe? Through your experience, does anyone out there have any suggestions and tips on how I can proceed with re-addressing my subnets. If I designed this network I would have gone with a 10.0.0.0 (mask 255.255.255.0) so I am leaning towards changing it to fit. Thank you.

    Read the article

  • Inconsistent DHCP replies with Windows 2008R2 DHCP server

    - by verbalicious
    I've got a Windows 2008R2 standard server running DHCP services. We've noticed that certain clients are receiving inconsistent DHCP replies. We have over 175 Windows workstations in this VLAN that don't seem to have trouble getting DHCP leases. However, PXE-booting clients trying to reach our DHCP server are able to get a lease inconsistently. Additionally, we tried using the "dhcping" tool against our DHCP server and found that roughly two of every three requests time out with "no answer" -- and this holds true when we set the timeout value on dhcping to 20seconds. After a failed attempt, however, we may get a dhcp lease reply immediately with dhcping. This leads me to believe that this issue isn't confined to PXE booting clients, but something more systemic with my LAN layer2 or DHCP. And that possibly my 175 windows clients are experiencing this in some form without my knowledge. We have over 30% of our scope available so the addresses are there. I was unable to find anything in the Windows server "DHCP-Server" log. Of course, my goal is to have my DHCP server reply to every request that it receives on the LAN!

    Read the article

  • Mac computers unable to connect to samba

    - by tan-ce
    I have a Ubuntu 9 server with samba 3.3 installed. This server has two network interfaces, one to a "public network" which I do not have any control over and another to a private LAN. On the private LAN, samba is the Domain Controller and nmbd is the WINS server on that network. On the "public network", I have configured a second instance of nmbd to run as a WINS client. The setup seems to work fine for Windows XP (on the domain or otherwise) as well as other Ubuntu machines. Finally, my question: Mac computers seem unable to connect to the samba server. As far as I can tell, it is as if samba is invisible to the MAC computer. Could my configuration of nmbd be causing this problem? Or is this simple a Mac oddity and is there anything I can do about it? New updates/info: We tried to connect through the Finder - Connect to Server, we entered smb://servername where servername is the netbios and DNS name. (There is also a DNS entry for the same name on the network) We also tried connecting by IP address Also, I just realized that there is at least one Mac which can connect. (Leopard 10.5.8) I will try to get the Mac OS versions of the computers which couldn't connect as soon as I can. The Mac which could not connect was running Mac OS X 10.4.11. Was there a change to samba on Mac OS between 10.4 and 10.5?

    Read the article

  • Google Chrome doesn't want to access Facebook

    - by Pieter van Niekerk
    I have been experiencing a bit of a problem with Chrome over the last couple of days where it doesn't want to access Facebook. When I open Chrome it works fine for a while and then if I were to refresh the page it would give me the Chrome 'This webpage is not available' message. This webpage is not available Google Chrome could not load the webpage because www.facebook.com took too long to respond. The website may be down, or you may be experiencing issues with your Internet connection. Here are some suggestions: Reload this webpage later. Check your Internet connection. Restart any router, modem, or other network devices you may be using. Add Google Chrome as a permitted program in your firewall's or antivirus software's settings. If it is already a permitted program, try deleting it from the list of permitted programs and adding it again. If you use a proxy server, check your proxy settings or contact your network administrator to make sure the proxy server is working. If you don't believe you should be using a proxy server, adjust your proxy settings: Go to the wrench menu Options Under the Hood Change proxy settings... LAN Settings and deselect the "Use a proxy server for your LAN" checkbox. This problem only persists when using the proxy and doesn't occur at all when not on the proxy. I have also tried different browsers (IE9 and Firefox 9.01) but it doesn't occur in any of them. This problem goes away for a while when I restart Chrome, only to happen again a couple of minutes later. I have tried deleting the cookies for Facebook without restarting Chrome, but to no avail. I am using Windows7 with Chrome 17

    Read the article

  • port forwarding with socks over proxy

    - by Oz123
    I am trying to browse a wiki that runs on a server inside one domain from another domain. The wiki is accessible only on the LAN, but I need to browse it from another LAN to which I connect with an SSH tunnel ... Here is my setup and the steps I did so far: ~.ssh/confing on wikihost: Host gateway User kisteuser Port 443 Hostname gateway.companydomain.com ProxyCommand /home/myuser/bin/ssh-https-tunnel %h %p # ssh-https-tunnel: # http://ttcplinux.sourceforge.net/tools/stunnel Protocol 2 IdentityFile ~/.ssh/key_dsa LocalForward 11069 localhost:11069 Host server1 User kisteuser Hostname localhost Port 11069 LocalForward 8022 server1:22 LocalForward 17001 server1:7100 LocalForward 8080 www-proxy:3128 RemoteForward 11069 localhost:22 from wikihost myuser@wikihost: ssh -XC -t gateway.companydomain.com ssh -L11069:localhost:22 server1 on another terminal: ssh gateway.companydomain.com Now, on my companydomain I would like to start firefox and browse the wiki on wikihost. I did: [email protected] ~ $ ssh gateway Have a lot of fun... kisteuser@gateway ~ $ ssh -D 8383 localhost user@localhost's password: user@wikiserver:~> My .ssh/config on that side looks like that: host server1 localforward 11069 localhost:11069 host localhost user myuser port 11069 host wikiserver forwardagent yes user myuser port 11069 hostname localhost Now, I started firefox on the server called gateway, and edited the proxy settings to use SOCKSv5, specifying that the proxy should be gateway and use the port 8383... kisteuser@gateway ~ $ LANG=C firefox -P --no-remote And, now I get the following error popping in the Terminal of wikiserver: myuser@wikiserver:~> channel 3: open failed: connect failed: Connection refused channel 3: open failed: connect failed: Connection refused channel 3: open failed: connect failed: Connection refused Confused? Me too ... Please help me understand how to properly build the tunnels and browse the wiki over SOCKS protocol. update: I managed to browse the wiki on wikiserver with the following changes: host wikiserver forwardagent yes user myuser port 11069 hostname localhost localforward 8339 localhost:8443 Now when I ssh gateway I launch Firefox and go to localhost:8339 and I hit the start page of the wiki, which is served on Port 8443. Now I ask myself is SOCKS really needed? Can someone elaborate on that ?

    Read the article

  • iptables secure squid proxy

    - by Lytithwyn
    I have a setup where my incoming internet connection feeds into a squid proxy/caching server, and from there into my local wireless router. On the wan side of the proxy server, I have eth0 with address 208.78.∗∗∗.∗∗∗ On the lan side of the proxy server, I have eth1 with address 192.168.2.1 Traffic from my lan gets forwarded through the proxy transparently to the internet via the following rules. Note that traffic from the squid server itself is also routed through the proxy/cache, and this is on purpose: # iptables forwarding iptables -A FORWARD -i eth1 -o eth0 -s 192.168.2.0/24 -m state --state NEW -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A POSTROUTING -t nat -j MASQUERADE # iptables for squid transparent proxy iptables -t nat -A PREROUTING -i eth1 -p tcp --dport 80 -j DNAT --to 192.168.2.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 80 -j REDIRECT --to-port 3128 How can I set up iptables to block any connections made to my server from the outside, while not blocking anything initiated from the inside? I have tried doing: iptables -A INPUT -i eth0 -s 192.168.2.0/24 -j ACCEPT iptables -A INPUT -i eth0 -j REJECT But this blocks everything. I have also tried reversing the order of those commands in case I got that part wrong, but that didn't help. I guess I don't fully understand everything about iptables. Any ideas?

    Read the article

  • IPv6 - Public IPs, private IPs, IPs derived from the MAC address? Confused!

    - by sinni800
    I'm pretty much excited for IPv6 because of the large address room and (potential?) owning of more than one IP, or even tens of IPs (/122 subnet?) Though one magazine has now confused me. In a current issue (no. 3) of "CT", a German computer magazine, I read that when using IPv6 your IP address consists of your MAC address and various other things, and that this address will be public on the web, no matter what access point / LAN you connect to. My knowledge of IP(v6) is in contrary of this. I thought you will normally always have a a local network IP and NAT takes care of your Internet access, and your provider gives the NAT router an IP. I've heard of the 6to4 interface, but does this one give you your own ip in the IPv6 net? Personally I hope it still is through a personal IP space (like 192.168, 127.16-31, 10. in IPv4) in private networks with a NAT going to the Internet. And also I hope that providers will offer subnets to private customers so they don't have to use NAT anymore. Yay for converting your LAN into the WAN and using better security (so Computers from the same subnet still get access rights like normal).

    Read the article

  • Blocking HTTPS and P2P Traffic

    - by Genboy
    I have a Debian server running at the gateway level on a LAN. This runs squid for creating block lists of websites - for eg. blocking social networking on the LAN. Also uses iptables. I am able to do a lot of things with squid & iptables, but a few things seem difficult to achieve. 1) If I block facebook through their http url, people can still access https://www.facebook.com because squid doesn't go through https traffic by default. However, if the users set the gateway IP address as proxy on their web browser, then https is also blocked. So I can do one thing - using iptables drop all outgoing 443 traffic, so that people are forced to set proxy on their browser in order to browse any HTTPS traffic. However, is there a better solution for this. 2) As the number of blocked urls increase in squid, I am planning to integrate squidguard. However, the good squidguard lists are not free for commercial use. Anyone knows of a good squidguard list which is free. 3) Block yahoo messenger, gtalk etc. There are so many ports on which these Instant Messenger softwares work. You need to drop lots of outgoing ports in iptables. However, new ports get added, so you have to keep adding them. And even if your list of ports is current, people can still use the web version of gtalk etc. 4) Blocking P2P. Haven't been able to figure out how to do this till now.

    Read the article

  • How to publish internal data to the internet - as simple as possible

    - by mlarsen
    I Asked this at Staock Overflow, but I would like your oppinion too as it has as much to do with administration as it does with coding. We have a .net 2-tier application where a desktop program is talking to a database. We support MS SQL Server 2000, 2005, 2008 and Oracle 9, 10 and 11. The application is sold, not as shrink-wrap, but pretty close. It is quite important for us that the installation and configuration is as easy as possible as installation instructions are usually supplied in written form to the customers internal IT-department. Our application is usually not seen as mission critical for the IT-department, so we need to keep their work down to a minimum. Now we are starting to get wishes for a web application build on top of the same data. The web application will be hosted by us and delivered as a SaaS application. Now the challenge is how to move data back and forth between the web application and the customers internal database. as I see it we have some requirements: We must be ready to handle the situation where the customers database is not accessible from the DMZ. I guess the easiest solution is that all communication is initiated from inside the customers lan. As little firewall configuration as possible. The best is if we can run without any special configuration as long as outgoing traffic from the customers lan are not blocked. If we need something changed in the firewall, we must be able to document that the change is secure. It doesn't have to be real time. Moving data in batches every ten minutes or so is OK. Data moves both ways, but not the same tables, so we don't have to support merges. It would be nice if we don't have to roll our own framework completely. Looking forward to hear your suggestions.

    Read the article

  • when vpn is connected intenet is not accessible

    - by javapowered
    I need vpn to access certain lan. The problem is - when I connect to vpn intenet stop working. But I need to have access to lan and intenet at the same time. When VPN is connected and I try tracert, I receive "The network is unreachable" message. Sorry about Russian language below, this is copy-pasted from console: C:\Users\Oleg>tracert 173.194.69.102 ??????????? ???????? ? bk-in-f102.1e100.net [173.194.69.102] ? ???????????? ?????? ??????? 30: 1 * * * ???????? ???????? ???????? ??? ???????. 2 1.1.1.1 ????????: ???????? ???? ??????????. ??????????? ?????????. How can I fix this problem?

    Read the article

  • Routing table on Linux not respected

    - by MRHaarmann
    I have a very specific problem, building a Linux VPN endpoint (with external VPN Gateway), which should route certain networks over the tunnel, others via default gateway. The Linux VPN should do a NAT on the outgoing connections for the VPN peers. Setup is as following: Internet gateway LAN 192.168.25.1/24 VPN Gateway LAN 10.45.99.2/24 (VPN tunnel 10.45.99.1 to net 87.115.17.40/29, separate connection to Internet) Linux VPN Router eth0 192.168.25.71/24 eth0:503 10.45.99.1/24 Default 192.168.25.1 route to 87.115.17.40/29 via 10.45.99.2 (send_redirects disabled, ip_forward enabled) Linux clients (multiple): eth0 192.168.25.x/24 Default 192.168.25.1 route to 87.115.17.40/29 via 192.168.25.71 Ping to the machines via tunnel from the VPN Router is working. Now I want to establish a routing from my clients over the VPN gateway and the client packet gets routed to 192.168.25.1 ! traceroute output shows the packets get routed to 192.168.25.71, but then to 192.168.25.1. So the route is not respected in forward ! IPTables and Routing: ip route show 87.115.17.40/29 via 10.45.99.2 dev eth0 10.45.99.0/24 dev eth0 proto kernel scope link src 10.45.99.1 192.168.25.0/24 dev eth0 proto kernel scope link src 192.168.25.71 default via 192.168.25.1 dev eth0 iptables -A INPUT -i eth0:503 -j REJECT iptables -t nat -A POSTROUTING -o eth0:503 -j MASQUERADE iptables -A FORWARD -i eth0:503 -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 192.168.25.0/24 -o eth0:503 -j ACCEPT So what is wrong with my setup ? The route is chosen correctly from localhost, but all the clients get forwarded to the Internet GW. thanks for helping, Marcus

    Read the article

  • Vlaning on WNR3500L

    - by ageis23
    When I try connecting to my wireless network it attempts to connect then gives up. There's something strange going on with the mac's. The eternet switch and all the vlan interfaces have a mac 00:FF:FF:FF:FF:FF. config 'switch' 'eth0' option 'vlan0' '2 3 4 8*' option 'vlan1' '0 8' option 'vlan2' '1 8' config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'type' 'bridge' option 'ifname' 'eth0.1' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ipaddr' '192.168.2.1' option 'ip6addr' '' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' option 'ipaddr' '192.168.1.8' option 'ip6addr' '' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '192.168.1.253' config 'interface' 'dmz' option 'ifname' 'eth0.2' option 'proto' 'static' option 'ipaddr' '192.168.0.1' option 'netmask' '255.255.255.0' Any help on this will be greatly appreciated! When I try setting the mac using macaddr it does nothing. It works perfectly fine when I turn the authentication off. I've also discovered that when wpa2 is switched on I don't receive a association reply from ap. thats my hostapd.conf interface=eth1 driver=broadcom bridge=br-lan ssid=O2BB3 wpa=2 wpa_passphrase=prettywoman wpa_key_mgmt=WPA-PSK rsn_pairwise=CCMP Btw that password is only temporary while am testing.

    Read the article

  • Flow of packet in network

    - by user58859
    I can't visualize in my mind the network traffic flow. eg. If there are 15 pc's in a LAN. When packet goes from router to local LAN, do it passes all the computers? Means did it goes to ehernet card of every computer and those computers accept the packet based on their physical address. To which pc the packet will go first? To the nearest to the router? What happen if that first pc captures that packet(though it is not for it)? What happens when a pc broadcast a message? Do it have to generate 14 packets for all the pc's or only one packet reach to all pc's? If it is one packet and captured by first pc, how other pc's can get that? I can't imagine how this traffic is exactly flows? May be my analogy is completely wrong. Can anybody explain me this? Thanks in advance.

    Read the article

  • Copy all installed programs & files in a hard disk (which has 32 bit Windows 7) and clone/transfer it to another computer which has 64 bit Windows 7

    - by galacticninja
    I recently got a new PC which has a 64-bit Windows 7 installed. The current PC that I am using has a 32-bit Windows 7 installed. I would like to know if there is a software that can copy all my installed programs and files in the hard disk with the 32-bit Windows 7 PC and transfer it to the newer PC's hard disk which has a 64 bit version of Windows 7. This is essentially like "cloning" a hard disk but I would like to use a 64-bit OS in the target drive, instead of also using the 32-bit OS of the source drive. I would like to do this I can avoid reinstalling and reconfiguring my installed programs and files again on the new PC. If possible, I would like the new PC to work as it was in my previous PC, with the installed programs, configuration and files intact except that the OS is now 64-bit and the hard disk has a larger capacity. I have heard of programs that can clone a hard disk, but my concern is that the 32-bit Windows 7 OS will also be cloned to the new 64-bit PC. If it is not possible to transfer my installed programs and settings like the way I described, are there software that can make it easier to migrate my installed programs, their configurations and my files from a 32-bit Windows 7 PC to a 64-bit Windows 7 PC? Details: I have a SATA to USB connector/adapter to copy files in the current hard disk to the newer one. The two PCs are connected through LAN, so I can also transfer files through LAN. Both PCs only have one hard disk.

    Read the article

< Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >