Search Results

Search found 16417 results on 657 pages for 'computer linguist'.

Page 554/657 | < Previous Page | 550 551 552 553 554 555 556 557 558 559 560 561  | Next Page >

• DD-WRT PPTP VPN problem

  - by Tobias Tromm

  I try to configure a DD-WRT as a PPTP client. The VPN Server is Windows Server 2003. This is my scenario: The Windows 2003 Server has set to give to the VPN Client the 10.0.0.81 fixed IP and to add a network route to the remote home. At the remote home I have changed the PPTP Options at DD-WRT to make the connection. The VPN connection is successfully established. ...and Windows successfully add the route to the remote home 192.168.2.X. From the remote home I can successfully access any computer from the VPN server side. The problem is when I try to access the remote home from the Server side. From Server side I only can access\ping DD-WRT ( by VPN Client IP - 10.0.0.81). What's wrong? How I need to do to be a site-to-site VPN? This is what happen when I try to tracert the remote home from local home.

  Read the article

• How to configure Farsun USB barcode scanner to not auto-trigger

  - by David Grayson

  At my company we have several USB barcode scanners. I'm not sure exactly what model they are, but I think they are the FG9800 from Farsun because that's what they look like on the exterior. They came with a programming manual that is very similar to this document from the Farsun website. When I scan the "Output Firmware Version" barcode, my scanner types the following into the computer: Farsun V2.00 2011-01-01 Is it possible to configure these scanners so they only read barcodes in response to the trigger button being pressed? I don't want them to automatically read barcodes. Additionally, I want this setting to be remembered while the scanner is turned off. Since this scanner only has a USB port, the only way to configure it that I know of is to scan bar codes from the manual (or make your own). I have tried scanning the configuration bar codes for Single Scan (013300), Single Scan No Trigger (013301), and Laser/CCD Timeout - 5 Seconds (0134005) from this document. Sometimes (but not often) this puts the scanner in to the right mode, where it only scans when the button is pressed. Unfortunately, the scanner seems to always leave this mode when it is power cycled. I have also scanned the "Reset Configuration To Defaults" barcode (0B) many times. We have three different scanners like this and I have not been able to successfully configure any of them. If the things I want are not possible with these Farsun-based scanners, is there some other scanner we can use?

  Read the article

• Can't view other computers on Network

  - by Darkart

  Systems: My Machine: Windows 7 Ultimate connected through ethernet into router Her Machine--Other Machine: Windows 7 Ultimate connected through wireless Router:F5D8236-4 N Wireless Router Version 1 Firmware: 2.01.03 (Apr 28 2009) ISP: Comcast Problem: I can not view the "Other Machine" on the network at all. I opened command prompt and ran net view and saw the pc name. I tried pinging the pc and it times out. Went inside the router and tried viewing the computer on the DHCP list and it can not be seen. I restored the router back to default settings and firmware and completely reset the modem and router, and created home group. I went to the other machine to configure home group settings and made sure that both PC's had identical settings. She was able to see my machine but I could not see hers. I restarted both machines and now we cant see each other at all. Also her PC ("Other Machine") had exclamation mark in the wireless icon but was connected just fine. There is no firewalls on currently or anti-virus enabled, and still can not see each other. Right now I am checking for updated drivers for the wireless card, but my question is could it be the router or something hardware related? I have went through all the settings in the Home group and visited most FAQ's and still no luck. Also as it stands I can not view her machine inside the router DHCP Client List :(

  Read the article

• Weird routing issue

  - by Joel Coel

  I'm having some weird internet problems on campus. I know it's something simple, but it's a case where I need another set of eyes. I think I can explain the problem best by posting a tracert: Tracing route to google.com [74.125.45.147] over a maximum of 30 hops: 1 3 ms 3 ms 3 ms 192.168.8.1 2 1 ms 1 ms 1 ms elissaemily-pc.york.edu [192.168.10.5] 3 2 ms 2 ms 2 ms rrcs-76-79-19-33.west.biz.rr.com [76.79.19.33] 4 31 ms 3 ms 2 ms ge-1-1-0.lnclne00-mx41.neb.rr.com [76.85.220.109] 5 20 ms 17 ms 17 ms ge-7-3-0.chcgill3-rtr1.kc.rr.com [76.85.220.137] 6 20 ms 20 ms 19 ms ae-5-0.cr0.chi30.tbone.rr.com [66.109.6.112] 7 19 ms 19 ms 24 ms ae-1-0.pr0.chi10.tbone.rr.com [66.109.6.155] 8 26 ms 24 ms 24 ms 74.125.48.109 9 23 ms 24 ms 21 ms 216.239.46.246 10 39 ms 39 ms 55 ms 209.85.242.215 11 39 ms 39 ms 39 ms 209.85.254.243 12 39 ms 40 ms 96 ms 209.85.253.145 13 39 ms 39 ms 39 ms yx-in-f147.1e100.net [74.125.45.147] Trace complete. Note the second entry in there. Not only is the host name a student's computer, but the ip address doesn't exist. Dhcp shows that host as having a different address and you can't ping any 192.168.10.5. Yet somehow it's routing packets for us (and not very well, either — things are slow right now). The basic network routing table looks like this: Destination Subnet Mask Gateway --------------------------------------- Default Route -- 10.1.1.5 (our firewall) 10.0.0.0 255.0.0.0 -- 192.168.8.0 255.255.252.0 --

  Read the article

• Setting up a PC for the Kids

  - by Martin Clarke

  I recently finished building a new PC from scratch; and then I decided to treat myself to a new widescreen monitor. I'm left with a bit of a conundrum with what to do with my old box. I'm considering a few options such as a file server, putting Linux on it, putting it elsewhere in the house or giving it to a member of the family and so on. But to be honest, I don't really think it would get much use. I've started thinking about putting together something for my kids. The oldest is coming up on 4 in a couple of months and he's used my PC and Macbook (supervised!) before for playing jigzaw puzzles, babysmash and so forth. He's also uses the computer at his nursery (Kindergarden for North Americans!). So, its got me thinking about setting something up for him (bonus for his brother who is 2). I was wondering what others had done when trying to put together something for their kids? Some points for consideration: Operating System? Software? Anti-virus Internet (probably blocking?) Hardware (I've seen some keyboards designed with kids in mind)

  Read the article

• Can’t connect to SQL Server 2008 - looks like Shared Memory problem

  - by user38556

  I am unable to connect to my local instance of SQL Server 2008 Express using SQL Server Management Studio. I believe the problem is related to a change I made to the connection protocols. Before the error occurred, I had Shared Memory enabled and Named Pipes and TCP/IP disabled. I then enabled both Named Pipes and TCP/IP, and this is when I started experiencing the problem. When I try to connect to the server with SSMS (with either my SQL server sysadmin login or with windows authentication), I get the following error message: A connection was successfully established with the server, but then an error occurred during the login process. (provider: Named Pipes Provider, error: 0 - No process is on the other end of the pipe.) (Microsoft SQL Server, Error: 233) Why is it returning a Named Pipes error? Why would it not just use Shared Memory, as this has a higher priority order in the list of connection protocols? It seems like it is not listening on Shared Memory for some reason? When I set Named Pipes to enabled and try to connect, I get the same error message. My windows account is does not have administrator priviliges on my computer - perhaps this is making a difference in some way (as some of the discussions in this post about an "SuperSocketNetLib\Lpc" registry key seems to suggest). I have tried restarting the SQL Server service, by the way, and also tried to get someone to log onto the machine with an admin account to restart the SQL Server service. Still no luck.

  Read the article

• award phoenix bios not recognizing my sata hdd.

  - by josh

  What am I doing wrong? I have a custom built comp with a Fatal1ty AA8XE mobo. It has 4 SATA ports and one IDE port. When i first got it, I had a really hard time putting in more than one hard drive. Right now i have one 120gb IDE HDD on master and my DVD+-RW on slave connected to the one IDE spot on the mobo. I ripped a bunch of movies and filled up my HDD, so I got a WD 80gb SATA drive. I plugged it into SATA1 and hooked up the power, turned on comp, went into bios. The only thing in any option in any of the menues in this crazy lookin bios is a thing that says "SATA mode". i put it on IDE, set it so PATA is primary, SATA is secondary. booted up my comp, nothin. Not recognizing the SATA. I went back into the bios and checked it all again. I saw that it says SATA2 and SATA4 are the secondaries so i put it on SATA2, booted, nothing, same with SATA4, same with SATA3, all same as SATA1. Bios and wt os are not recognizing the drive as being there at all. I even downloaded and printed the almost 100 page manual for the mobo, read the entire thing, and still can't figure it out. I know there are a lot of people out there smarter than me when it comes to computers. So please, somebody, anybody, please tell me something that I'm not seeing. Some setting somewhere that I didn't configure right. There is something, obviously, but I can't find it. As far as i can tell, everything is set perfectly fine for my 120gb to be the master and the SATA to be the slave. I don't know what I'm doing wrong but I'm seriously about to throw this computer out the window. thankyou in advance to whoever attempts to help.

  Read the article

• Apache2, making my site publicly available

  - by Shackler

  Hello, I want to make my apache 2 development server public to the internet, it is a Django based website. Here is my apache2 config: <VirtualHost *:80> Alias /media /home/user/myproject/statics Alias /admin_media /home/myuser/django/Django-1.1.1/django/contrib/admin/media WSGIScriptAlias / /home/myuser/myproject/myproject_wsgi.py WSGIDaemonProcess myproject user=myuser group=myuser threads=25 WSGIProcessGroup myproject </VirtualHost> When I do netstat -lntup I get: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN - tcp6 0 0 :::80 :::* LISTEN - tcp6 0 0 :::22 :::* LISTEN - tcp6 0 0 ::1:631 :::* LISTEN - udp 0 0 0.0.0.0:5353 0.0.0.0:* - udp 0 0 0.0.0.0:38582 0.0.0.0:* I connect with ADSL thus I am behind a router. For this I have made my computer DMZ enabled to my machine. What can be the problem? When I try to login with my ip, I get my routers config page, when a friend tries to connect to me from internet, he gets "not authorized".

  Read the article

• Upgrading Visio 2000 to Visio 2007

  - by dirtside

  I have Microsoft Visio 2000 SR 1, and recently purchased Microsoft Office Visio Standard 2007 with the understanding (supported by the product info and some other research) that I'd be able to upgrade. However, when I install 2007, it tells me it can't find a previous install of Visio, but... it's right there! Here's the exact message: "Setup can't find a version of Microsoft Office on your computer. If Office is installed on a disk or network share, click the browse button to select the appropriate disk or share... (etc.)" No matter which directory or drive I pick (various Office installs, the old Visio install, various subdirectories) it gives the following message: "The path you have chosen does not point at a qualifying upgradeable product. Click 'Retry' to try again or 'Cancel' to quit setup." Any ideas? This is a legit copy of Visio 2007 (purchased from Amazon) and the copy of Visio 2000 is legit as well. I'm not sure what exactly the installer is looking for that it would consider a "qualifying upgradeable product". A specific file?

  Read the article

• Dynamically add Server 2008 NLB Nodes

  - by Nick Jacques

  Hi All, I have a small NLB cluster for Terminal Servers. One of the things we're looking at doing for this particular project (this is for a college class) is dynamically creating Terminal Servers. What we've done is create policies for a certain OU, that sets the proper TS Farm properties and installs the Terminal Server role and NLB feature. Now what we'd like to do is create a script to be run on our Domain Controller to add hosts to the preexisting NLB cluster. On our Server 2008 R2 Domain Controller, I was thinking of running the following PowerShell script I've kind of hacked together. Any thoughts on if this will work? Is there any way I can trigger this script to run on the DC once all the scripts to install roles are done on the various Terminal Servers? Thanks very much in advance!! Import-Module NetworkLoadBalancingClusters $TermServs = @() $Interface = "Local Area Connection" $ou = [ADSI]"LDAP://OU=Term Servs,DC=example,DC=com" foreach ($child in $ou.psbase.Children) { if ($child.ObjectCategory -like '*computer*') {$TermServs += $child.Name} } foreach ($TS in $TermServs) { Get-NlbCluster 172.16.0.254 | Add-NlbClusterNode -NewNodeName $TS -NewNodeInterface $Interface }

  Read the article

• How to disable 3rd party cookies in Chrome?

  - by David Nordvall

  I have both the "stop websites from storing local data" and the "block all third party cookies without exception" settings enabled in Chrome 12 (I'm not sure what the exact names of these settings are in english as I run Chrome with swedish localization). I do however have two problems. My first problem is that when I'm visiting one of my local news paper's site (and surely other), cookies from www.facebook.com is allowed for some reason. I suspect that the reason is that I have added an exception to the www.facebook.com domain but as the setting "block all third party cookies without exception" implies, that shouldn't matter. My second problem is that if I check what cookies are stored on my computer after browsing for a while, I have tons of cookies that are not on my white list. Primarily from ad services. My expectations from enabling the above mentioned settings was that only cookies that fulfill the two folling requirements would be accepted: the cookies must be from the domain in my address bar the cookies must be from a domain on my whitelist Apparently this isn't the case. The question is, have I completely misunderstood the settings or is this a bug? And, either way, is there a way to accomplish my desired behavior?

  Read the article

• Installing ubuntu 12.04, installs but does not boot after it asks me to remove the CD

  - by Randnum

  I'm Trying to install Ubuntu 12.04 on my computer. It had an old copy of Windows 7 on it I tried to reformat the hard drive for a fresh install of Ubuntu but I think I messed up the partitions in some way that prevents it from fully loading. I'm able to complete the install fine and use guided partitioning so it should be happy but when it gets about 90% through at the part that ejects the cd and restarts the system it fails. After ejecting the CD and restarting it just loads up the bios lenovo splash screen then purple then black. I can hear a sound from my speakers like some notification sound but there is no text on my screen. I've since gone back in under Rescue System to try and reconfigure the partitions hoping that it will fix it and i've tried several combinations. Currently it's SCST1 (0,0,0) (sda) - 500.1 GB ATA WDC WD5000AAkKX-0 #1 100.0 MB K biosgrub #2 494.1 GB B K ext4 / #3 5.9 GB F swap swap 8.2 kb FREE SPACE I'm not sure if I need to set the ext4 to contain the boot flag but if I don't include at least one partition with the boot flag enabled it complains saying that "The partition table format in use on your disks normally requires you to create a separate partition for boot loader code. This partitionshould be marked for use as an "EFI boot Partition" and should be at least 35 MB in size. Note that this is not hte same as a partition mounted on /boot" Like I said it seems to have installed all of the actual data from the CD it's just not properly booting for some reason

  Read the article

• In Windows 7, why can't I use perfmon against a remote server?

  - by SomeGuy

  I am on Windows 7 and trying to run perfmon against Windows 2003 and Windows 2008 servers. I am running into the same issue with all remote machines. When creating a data collector set, I specify a domain account that is in the administrators group on the remote machines (and "Performance Log Users" and "Performance Monitor Users" to be safe). On the "Available Counters" screen, When I type in a remote computer name, PerfMon locks up for a good 2-3 minutes before I can add any counters. I can then save the collector set. However, when I save it, the go/stop buttons are disabled if I click the set in the left panel, and missing if I click the Data collector set itself in the right panel. See the screens below. I can run data collector sets against my local machine with no problem. I am opening perfmon with my local account in both scenarios. I also have Remote Registry Service started on each remote machine. What is going on?

  Read the article

• Linux error when resume from RAM

  - by TuxPotato

  The last two times that I have resumed my laptop from sleep, it has hung and given me this set of errors: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 hda_intel: azx_get_responce timeout, switching to single_cmd mode: last cmd=0x01170700 ata6: softreset failed (device not ready) ata4: softreset failed (device not ready) [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 The last two messages repeat two more times. The first time this happened, Linux's Magic SysRq worked and did a soft reboot, and after that everything was fine till it went to sleep again. It wakes up and gives me this. Here are the laptop stats: Toshiba Satellite L455D-S5976 AMD Sempron SI-42 Processor 2GB DDR2 RAM HD TruBrite Display ATI Radeon Graphics (integrated) Running Ubuntu 10.10 32 bit I'm not sure about the hard drive, but its a 250GB drive with one NTFS partition, two Hidden NTFS, one Linux Swap, and one Ext4. Can someone tell me whats wrong with my laptop? NOTE: This only happens when I close the screen. My computer doesn't go to sleep with the screen open.

  Read the article

• Printer deployment via Group Policy not working on a single system

  - by Aron Rotteveel

  One of my coworkers just got a new laptop running Windows 7 Pro x64. We use a GPO to deploy the printers to every system, but for some reason it is not working on this system. I have been breaking my head over this for the past 3 hours now without any result. The strange thing is that gpresult /H seems to indicate that the GPO did run. The hardware: Laptop: Windows 7 Professional x64 Print server: Windows Server 2008 x64 R1 HP Color LaserJet 2605dn HP LaserJet P2015 Driver packages on server: HP universal printer driver PCL5, both X86 as X64 Oddities and other info: GPO working flawlessly on every other system, including my own Windows 7 Ultimate X64 laptop gpresult /H shows the GPO being ran Windows Firewall completely disabled on the new laptop Below is the output for gpresult /H (in Dutch sadly, but I think you'll recognize it): Beleidsregels Windows-instellingen Printerverbindingen Pad Dominerend groepsbeleidsobject \\Server2008\HP Color LaserJet 2605dn Printers \\Server2008\HP LaserJet P2015 Printers Beheersjablonen Beleidsdefinities (ADMX-bestanden) opgehaald van de lokale computer. Configuratiescherm/Printers Beleid Instelling Dominerend groepsbeleidsobject Beperkingen van point-and-print Uitgeschakeld Printers Like I said, I have been trying to figure this out for the past few hours or so without any result, so you are my last hope. Any help is appreciated.

  Read the article

• Created new torrent but client unable to find seeds

  - by ehfeng

  I tried creating a new torrent, using uTorrent, following the directions from torrentfreak (http://torrentfreak.com/how-to-create-a-torrent/). I used a bunch of trackers (just in case any individual one was having troubles) and uTorrent shows it as "seeding" with 100% of the file. It shows: seeds 0(1), peers 0(0). http://exodus.desync.com/announce http://eztv.tracker.prq.to/announce http://open.tracker.thepiratebay.org/announce http://www.torrent-downloads.to:2710/announce http://denis.stalker.h3q.com:6969/announce udp://denis.stalker.h3q.com:6969/announce http://www.sumotracker.com/announce I've also attempted to remove the torrent and then re-add the torrent, pointing it to my already existing files, forcing uTorrent to recheck the files and then begin seeding. Yet when I share the .torrent file with my other computer and attempt to download, it is unable to find any peers or seeds. To confirm that both clients are working, I downloaded a torrent on both computers, using their respective clients, using torrents I found on isohunt. This tells me that there must be something wrong in how I'm creating my torrents. Any help is appreciated.

  Read the article

• Networking "chokes" on Windows 7 64 bit

  - by Rohit Nair

  I've been having this problem for some months now, and I have been unable to figure out a solution, or even the cause. At random points throughout the day, my internet connectivity "freezes". I don't get disconnected from my local wireless network. My router doesn't get disconnected from the world. However, for some reason, my computer stops receiving packets. If I'm playing an MMO ( World of Warcraft, in this case, but it has happened with Eve Online as well ) all activity just freezes. If I try to browse, Opera, Firefox and IE all stall at "Waiting for google.com..." or whatever the hostname may be. Inspection with a packet sniffer seems to reveal that there are no incoming packets. Here's the interesting part. Disconnecting from my wireless network and reconnecting fixes the issue. Obviously this led me to conclude that it was a problem with my router or wireless card. However, I have tweaked all the settings on my router that I could think of, including things like QoS, AP Isolation, etc. with no change. My wireless card doesn't really have that many options, and I have uninstalled and reinstalled drivers a few times without any change. Windows Firewall on/off doesn't make a difference. Anyone have any suggestions for debugging this? It's becoming an annoyance.

  Read the article

• HP c6180 driver refuses to install - "must reboot to continue delete files and continue install" loo

  - by Aszurom

  User called me last night, can't get HP drivers to install for printer. 500 meg download for latest c6180 driver. PC says "computer must be restarted to delete some files, then setup will continue." and it won't pass that point. (that's not exact phrasing of the error, and I'm not on the system now) Target machine is XP SP2. I upgraded to SP3. Fully patched. Ran malwarebytes, spybot, hijack this and turned off all startup entries. I noted that windows update also failed on optional printer driver updates for other printers installed on the machine. Went to printer server properties, removed all print drivers from system, deleted all printer ports. Made sure no services were marked disabled. After 5 hours of fighting this I started to get desperate, and uninstalled anything that referenced HP in the machine at all. Still no cure. I'm 6 hours into this and completely stumped. Google returns nothing applicable except unanswered requests for help on same topic.

  Read the article

• Ripping a home video VCD on Linux or Windows with VLC or otherwise

  - by user259774

  I have a VCD with 22 minutes of video on it. I would like to retain this footage and throw away the VCD. I can play the whole thing with VLC ("open disc - vcd - /dev/sr0 - play"): all 22 minutes of the main track. I don't believe there's any other content aside from the main track. I can seek to anywhere I want to within the 22 minute track. If I mount /dev/sr0 /media/vcd and then try to copy the only file from the MPEGAV folder, I get an I/O error, with an empty destination file. VLC has a "convert" option in addition to "play". When I use this I actually get a good OGG file back, after it runs through the video in painful real-time. I guess it dubs it frame-by-frame. But the file is only 10 minutes long, leaving 12 minutes off of the track. Handbrake doesn't detect it's track titles, unfortunately. I don't know if I should start getting involved with GNU ddrescue or if it's because VCDs somehow encode their data sectors differently. Anyway, I'm in way over my head and if anyone knows how I could get that video track off the thing, feel free to share! Edit: I should note that I also have access to a Windows computer

  Read the article

• Installing SATA dvd burner on machine with no spare SATA ports/connectors

  - by Faheem Mitha

  Greetings. I have the following motherboard Tyan Thunder K8WE S2895A2NRF Motherboard - extended ATX - nForce Pro 2200/2050 - Socket 940 - UDMA133, Serial ATA-300 (RAID) - 2 x Gigabit Ethernet - FireWire - 6-1 channel audio This is part of a computer that was assembled in the winter of 2006/2007. The user manual says the following with regard to SATA Integrated SATAII Generation 1 Controllers (from NForce Professional 2200) Two integrated dual port SATA II controllers Four SATA connectors support up to four drives 3 Gb/s per direction per channel NvRAID v2.0 support Supports RAID 0, 1, 0+1 and JBOD. I just purchased a SATA DVD burner. Here is the page for the product http://www.amazon.ca/gp/product/B002QGDWLK/ The problem I am facing is that I already have 4 SATA drives installed. I don't want to remove any of them. However, I want the DVD burner above installed as well. The person I am consulting with here (Bombay, India) tells me that my four available SATA ports are filled, and that my only option is to install a SATA card into the one free PCI slot on the motherboard. However, he says that with this setup I will not be able to boot from the DVD drive. Are these statements correct, and what are my other options if any? Even it the statements in the last para are true, I suppose I could use one of the motherboard connectors/ports there are currently being used with the hard drives with the DVD drive, and use the "add-on" connector with one of the hard drives. Not all the 4 hard drives need to be bootable. BTW, despite having read through http://en.wikipedia.org/wiki/Serial_ATA#Cables.2C_connectors.2C_and_ports I am fuzzy on the differences between connectors, cables and ports. Thanks in advance.

  Read the article

• What's hogging my CPU?

  - by endolith

  Ubuntu's System Monitor applet shows 100% CPU usage continuously. If I click it, the resources tab shows it at 100% continuously, too. If I go to processes, though, to find out which process is the culprit, there is nothing above 10%. If I run top there is nothing above 10%. I try killing lots of things, but it continues at 100%. How can I find out what's hogging the CPU? This is an unusual situation on a computer I use daily, that normally only hits 100% CPU when I'm doing something that requires it (like loading 32 Firefox tabs) after which it goes back to a normal idle level. It's not a new install or anything. It shouldn't be maxed out. I'm not sure when it started or if I changed something that caused it to happen. Normally I would use top or System Monitor and find the process that had gone out of control, but I can't find anything with those tools this time. It persists after reboots and everything. And the processor is obviously hot, so it's not an erroneous reading. Update: I tried killing any process I saw active again, and killing vino-server finally fixed the problem, even though it never went above 5%. I had enabled Remote Desktop a few days ago (and have obviously now disabled it). How did it manage to use 100% CPU while top only showed it as 5% or so? How do I identify the culprit in the future? Looks like I'm not the only one: Still a problem in both jaunty & karmic. Interestingly, both System Monitor & htop do not show the sum of individual processes being anywhere near 100% cpu.

  Read the article

• Dismount USB External Drive using powershell

  - by JC

  Hello, I am attempting to dismount an external USB drive using powershell and I cannot successfuly do this. The following script is what I use: #get the Win32Volume object representing the volume I wish to eject $drive = Get-WmiObject Win32_Volume -filter "DriveLetter = 'F:'" #call dismount on that object there by ejecting drive $drive.Dismount($Force , $Permanent) I then check my computer to check if drive is unmounted but it is now. The boolean parameters $force and $permanent have been tried with different permutations to no avail. The exit code returned by the dismount command changes when the params are toggled. (0,0) = exit code 0 (0,1) = exit code 2 (1,0) = exit code 0 (1,1) = exit code 2 The documentation for exit code 2 indicates that there are existing mount points as a reason why it cannot dismount. Although I am trying to dismount the only mount point that exists so I am unsure what this exit code is trying to tell me. Having already trawled the web for people experiencing similar problems I have only found one additional command to try and that is the following: # executed after the .Dismount() command $drive.Put() This additional command does not help. I am running out of things to try, so any assistance anyone can give me would be greatly appreciated, Thanks.

  Read the article

• Setting up dnsmasq for a local network

  - by WishCow

  Me, and a small group of developers have just moved to a new office, and I'd like to set up dnsmasq on our development server, so when we deploy web apps there, we don't have to edit our own hosts files. We have a router at 192.168.3.1 which we don't have access to. I figured I'd install a DNS server on the development box, and we all record it's IP as a secondary DNS server. Unfortunately I'm strugling to make this work. The name of the devel server is devbox, it's IP is 192.168.3.99, and it's running the latest Ubuntu Server (Karmic) My computer is running Ubuntu Desktop (Karmic) What I'd like to achieve Let's say I have three websites, website1, website2, website3, running on the development box. I'd like to access them by the urls: http://website1.devbox http://website2.devbox http://website3.devbox So I have configured Apache on the devel box, installed dnsmasq, and put the following lines into it's hosts file: 192.168.3.99 website1.devbox 192.168.3.99 website2.devbox 192.168.3.99 website3.devbox and edited my own resolv.conf file to include the devel box as a nameserver: nameserver 192.168.3.99 It's working fine, I can access the sites. The problem is that it doesn't scale well. I'd like all the domains ending with .devbox forwarded to the development box, and this is what I'm struggling with. I have tried putting 192.168.3.99 devbox into the hosts file, and editing the line in dnsmasq.conf: # Add local-only domains here, queries in these domains are answered # from /etc/hosts or DHCP only. local=/devbox/ But I cannot get it working. If I try any url that is not explicitly present in the development box's hosts file, the dns lookup fails. Is the local directive for something else? Am I looking at the wrong place?

  Read the article

• Setting up dnsmasq for a local network

  - by WishCow

  Me, and a small group of developers have just moved to a new office, and I'd like to set up dnsmasq on our development server, so when we deploy web apps there, we don't have to edit our own hosts files. We have a router at 192.168.3.1 which we don't have access to. I figured I'd install a DNS server on the development box, and we all record it's IP as a secondary DNS server. Unfortunately I'm strugling to make this work. The name of the devel server is devbox, it's IP is 192.168.3.99, and it's running the latest Ubuntu Server (Karmic) My computer is running Ubuntu Desktop (Karmic) What I'd like to achieve Let's say I have three websites, website1, website2, website3, running on the development box. I'd like to access them by the urls: http://website1.devbox http://website2.devbox http://website3.devbox So I have configured Apache on the devel box, installed dnsmasq, and put the following lines into it's hosts file: 192.168.3.99 website1.devbox 192.168.3.99 website2.devbox 192.168.3.99 website3.devbox and edited my own resolv.conf file to include the devel box as a nameserver: nameserver 192.168.3.99 It's working fine, I can access the sites. The problem is that it doesn't scale well. I'd like all the domains ending with .devbox forwarded to the development box, and this is what I'm struggling with. I have tried putting 192.168.3.99 devbox into the hosts file, and editing the line in dnsmasq.conf: # Add local-only domains here, queries in these domains are answered # from /etc/hosts or DHCP only. local=/devbox/ But I cannot get it working. If I try any url that is not explicitly present in the development box's hosts file, the dns lookup fails. Is the local directive for something else? Am I looking at the wrong place?

  Read the article

• Using Virtualbox Bridge Networking fails connection from Guest OS to Oracle XE running on Host

  - by Licheng

  I am trying to make a JDBC connection from a VirtualBox Ubuntu Guest OS to an Oracle XE database running o Host. However, the connection is refused. Here are the details of my environment: VirtualBox: 4.1.4 Host OS: Windows 7 Guest OS: Ubuntu server 11.4 Networking mode: Bridged network Oracle XE database running on Host Issue: WebLogic server runs on the Ubuntu virtualbox. It attempts to connect to an Oracle XE database running on the Host OS (windows 7) with listening port 1521. On the Guest OS (Ubuntu), I am able to ping the Host computer from the Guest OS. However, when I configured a JDBC data source on the WebLogic server on the Guest OS to connect to the Oracle XE, connection took a long time, and eventually I received an "IO Exception: The Network Adapter could not establish the connection". When I tried "telnet host-ip 1521", no connection was established. With Bridge networking, I can make bi-directional connections between the host and the guest OS (e.g. connection through ssh and ftp). Is there anything I missed in the setup of Bridge networking and the guest/host OS? Note that I was able to make the same connection within a normal networking environment (i.e. not using virtual box). I am not sure whether Bridge networking is a good option for the work described above. Should I use host-only networking mode? If so, any specific configurations I need to perform? I read through the Virtual box document on setting up the host-only network, however, it lacks of details. I followed the procedures described in the manual, and couldn't even connect to the host. Could some experts here enlighten me on this issue? Much appreciated. Licheng

  Read the article

< Previous Page | 550 551 552 553 554 555 556 557 558 559 560 561  | Next Page >