Search Results

Search found 1454 results on 59 pages for 'eth0'.

Page 56/59 | < Previous Page | 52 53 54 55 56 57 58 59  | Next Page >

• Can't ping Ip over bridge

  - by tmn29a

  I'm unable to ping another host over a bridge I created, I can't see the error -.- It's a remote machine running debian stable with some backports for which I want to set up DHCP on the new Subnet 172.30.xxx.xxx to be used for KVM-Guests. ifconfig : bond0 Link encap:Ethernet HWaddr e4:11:5b:d4:94:30 inet addr:10.54.2.84 Bcast:10.54.2.127 Mask:255.255.255.192 inet6 addr: fe80::e611:5bff:fed4:9430/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:34277 errors:0 dropped:0 overruns:0 frame:0 TX packets:18379 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2638709 (2.5 MiB) TX bytes:2887894 (2.7 MiB) br0 Link encap:Ethernet HWaddr f2:fc:4d:7f:15:f0 inet addr:172.30.254.66 Bcast:172.30.254.127 Mask:255.255.255.192 inet6 addr: fe80::f0fc:4dff:fe7f:15f0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:252 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:10800 (10.5 KiB) Pings : ping -I br0 172.30.xxx.65 PING 172.30.xxx.65 (172.30.xxx.65) from 172.30.xxx.66 br0: 56(84) bytes of data. --- 172.30.xxx.65 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2017ms ping -I bond0 172.30.254.65 PING 172.30.xxx.65 (172.30.xxx.65) from 10.54.2.84 bond0: 56(84) bytes of data. 64 bytes from 172.30.x.65: icmp_req=1 ttl=64 time=0.599 ms 64 bytes from 172.30.x.65: icmp_req=2 ttl=64 time=0.575 ms 64 bytes from 172.30.x.65: icmp_req=3 ttl=64 time=0.565 ms --- 172.30.x.65 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1999ms rtt min/avg/max/mdev = 0.565/0.579/0.599/0.031 ms Route : Destination Gateway Genmask Flags Metric Ref Use Iface 172.30.x.64 * 255.255.255.192 U 0 0 0 br0 10.54.x.64 * 255.255.255.192 U 0 0 0 bond0 default 10.54.x.65 0.0.0.0 UG 0 0 0 bond0 default 172.30.x.65 0.0.0.0 UG 0 0 0 br0 The Interface : cat /etc/network/interfaces auto lo br0 iface lo inet loopback # Bonding Interface auto bond0 iface bond0 inet static address 10.54.x.84 netmask 255.255.255.192 network 10.54.x.64 gateway 10.54.x.65 slaves eth0 eth1 bond_mode active-backup bond_miimon 100 bond_downdelay 200 bond_updelay 200 iface br0 inet static bridge_ports bond0 address 172.30.x.66 broadcast 172.30.x.127 netmask 255.255.x.192 gateway 172.30.x.65 bridge_maxwait 0 If you need more info please ask. Thanks for your help !

  Read the article

• VirtualBox Port Forward not working when Guest IP *IS* specified (while doc says opposite)

  - by Patrick

  Trying to port forward from host (Mac OS X) 127.0.0.1:8282 - guest (CentOS)'s 10.10.10.10:8080. Existing port forwards include 127.0.0.1:8181 and 9191 to guest without any IP specified (so whatever it gets through DHCP, as explained in the documentation). Here is how the non-working binding was added: VBoxManage modifyvm "VM name" --natpf1 "rule3,tcp,127.0.0.1,8282,10.10.10.10,8080" Here is how the working ones were added: VBoxManage modifyvm "VM name" --natpf1 "rule1,tcp,127.0.0.1,8181,,80" VBoxManage modifyvm "VM name" --natpf1 "rule2,tcp,127.0.0.1,9191,,9090" And by "non-working", I of course mean not listening (as a prerequisite to forwarding): $ lsof -Pi -n|grep Virtual|grep LISTEN VirtualBo 27050 user 21u IPv4 0x2bbdc68fd363175d 0t0 TCP 127.0.0.1:9191 (LISTEN) VirtualBo 27050 user 22u IPv4 0x2bbdc68fd0e0af75 0t0 TCP 127.0.0.1:8181 (LISTEN) There should be a similar line above but with 127.0.0.1:8282. Just to be clear, this port is listening perfectly fine on the guest itself. And when I remove the guest IP (i.e., clear the 10.10.10.10) the forward works fine, albeit to eth0 (not eth1 where I need it). I can tcpdump and watch the traffic flow back and forth. And yes, I've disabled iptables entirely while testing -- it's not getting blocked anywhere on the guest. As VirtualBox writes in their documentation, you are required to specify the guest IP if it's static (makes sense, no DHCP record it keeps): "If for some reason the guest uses a static assigned IP address not leased from the built-in DHCP server, it is required to specify the guest IP when registering the forwarding rule:". However, doing so (as I need to), seems to break the port forward with nary a report in any log file I can find. (I've reviewed everything in ~/Library/VirtualBox/). Other notes: While I used the above command to add the third rule, I've also verified it showed up correctly in GUI and then removed/re-added from there just to make sure). This forum link -- while very dated -- looks somewhat related in that a port forward to a static IP was not appearing (perhaps they think due to lack of gratuitous arp being sent for host to know IP is there/avail?). Anyway, what gives? Is this still buggy? Any suggestions? If not, easy enough workarounds? What's interesting is that this works perfectly fine on another user's Mac, however he's running a slightly older version (4.3.6 v. 4.3.12).

  Read the article

• Minidlna Directory Issues

  - by Somnambulist

  I've done my searching and can't find an answer to THIS specific issue. I have my minidlna set up and running - but it's not really done properly. First off, when I open the server on my bluray player, all of my movies are listed twice - when they are certainly not saved on my external twice. Second, when I open the server - rather than reading "Movies" "TV" "Music", etc - It just mashes all of my movies, tv, and some other folders all together with no real organization. I never had this problem when I had my Windows set up, so I know it's something configured improperly more-so than my external drive giving me gruff. Here's my minidlna.conf file: # This is the configuration file for the MiniDLNA daemon, a DLNA/UPnP-AV media # server. # # Unless otherwise noted, the commented out options show their default value. # # On Debian, you can also refer to the minidlna.conf(5) man page for # documentation about this file. media_dir=/media/somnambulist/Ghost In You # This option can be specified more than once if you want multiple directories # scanned. # # If you want to restrict a media_dir to a specific content type, you can # prepend the directory name with a letter representing the type (A, P or V), # followed by a comma, as so: # * "A" for audio (eg. media_dir=A,/var/lib/minidlna/music) # * "P" for pictures (eg. media_dir=P,/var/lib/minidlna/pictures) # * "V" for video (eg. media_dir=V,/var/lib/minidlna/videos) # # WARNING: After changing this option, you need to rebuild the database. Either # run minidlna with the '-R' option, or delete the 'files.db' file # from the db_dir directory (see below). # On Debian, you can run, as root, 'service minidlna force-reload' instead. #media_dir=/var/lib/minidlna media_dir=V,/media/somnambulist/Ghost In You/Movies media_dir=V,/media/somnambulist/Ghost In You/TV media_dir=P,/home/somnambulist/Pictures # Path to the directory that should hold the database and album art cache. db_dir=/home/somnambulist/serverart # Path to the directory that should hold the log file. log_dir=/home/somnambulist/serverlog # Minimum level of importance of messages to be logged. # Must be one of "off", "fatal", "error", "warn", "info" or "debug". # "off" turns of logging entirely, "fatal" is the highest level of importance # and "debug" the lowest. #log_level=warn # Use a different container as the root of the directory tree presented to # clients. The possible values are: # * "." - standard container # * "B" - "Browse Directory" # * "M" - "Music" # * "P" - "Pictures" # * "V" - "Video" # if you specify "B" and client device is audio-only then "Music/Folders" will be used as root root_container=B # Network interface(s) to bind to (e.g. eth0), comma delimited. #network_interface= # IPv4 address to listen on (e.g. 192.0.2.1). #listening_ip= # Port number for HTTP traffic (descriptions, SOAP, media transfer). port=8200 # URL presented to clients. # The default is the IP address of the server on port 80. #presentation_url=http://example.com:80 # Name that the DLNA server presents to clients. friendly_name=Somnambulist Media Server # Serial number the server reports to clients. serial=12345678 # Model name the server reports to clients. #model_name=Windows Media Connect compatible (MiniDLNA) # Model number the server reports to clients. model_number=1 # Automatic discovery of new files in the media_dir directory. #inotify=yes # List of file names to look for when searching for album art. Names should be # delimited with a forward slash ("/"). album_art_names=Cover.jpg/cover.jpg/AlbumArtSmall.jpg/albumartsmall.jpg/AlbumArt.jpg/albumart.jpg/Album.jpg/album.jpg/Folder.jpg/folder.jpg/Thumb.jpg/thumb.jpg # Strictly adhere to DLNA standards. # This allows server-side downscaling of very large JPEG images, which may # decrease JPEG serving performance on (at least) Sony DLNA products. #strict_dlna=no # Support for streaming .jpg and .mp3 files to a TiVo supporting HMO. #enable_tivo=no # Notify interval, in seconds. #notify_interval=895 # Path to the MiniSSDPd socket, for MiniSSDPd support. #minissdpdsocket=/run/minissdpd.sock` And here's the error I get in terminal when I run: sudo service minidlna restart sudo service minidlna force-reload Force restart error: Restarting DLNA/UPnP-AV media server minidlna [2013/08/12 21:19:27] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/Movies" not accessible! [Permission denied] [2013/08/12 21:19:27] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/TV" not accessible! [Permission denied] Force-reload error: Restarting DLNA/UPnP-AV media server minidlna [2013/08/12 21:19:46] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/Movies" not accessible! [Permission denied] [2013/08/12 21:19:46] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/TV" not accessible! [Permission denied] rm: cannot remove ‘/home/somnambulist/serverart/files.db’: Permission denied rm: cannot remove ‘/home/somnambulist/serverart/art_cache/media/somnambulist/Ghost In You/Movies/Slumdog Millionaire/Slumdog.Millionaire.Cover.jpg’: Permission denied rm: cannot remove ‘/home/somnambulist/serverart/art_cache/media/somnambulist/Ghost In You/Movies/Zack and Miri Make a Porno/ZackAndMiriMakeAPornoCover.jpg’: Permission denied [2013/08/12 21:19:46] minidlna.c:744: warn: Failed to clean old file cache. [ OK ] I've spent hours on this at this point, read through various files - and even had a friend who is relatively Ubuntu-savvy try to help me via chat - no such luck. Thanks in advance for any help.

  Read the article

• Wireless cuts out on Toshiba Satellite S7208

  - by alecRN

  I recently got a Toshiba Satellite L875-S7208 with Windows 7 preinstalled. I installed Ubuntu 12.04 LTS dual boot to the same Windows partition. However, usually 15 minutes or less after booting, the wifi connection dies. Here's some hopefully relevant information: lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) Subsystem: Toshiba America Info Systems Device [1179:fb40] Kernel driver in use: i915 Kernel modules: i915 00:14.0 USB controller [0c03]: Intel Corporation Panther Point USB xHCI Host Controller [8086:1e31] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: xhci_hcd 00:16.0 Communication controller [0780]: Intel Corporation Panther Point MEI Controller #1 [8086:1e3a] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation Panther Point High Definition Audio Controller [8086:1e20] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb40] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 1 [8086:1e10] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 2 [8086:1e12] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 3 [8086:1e14] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #1 [8086:1e26] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge [0601]: Intel Corporation Panther Point LPC Controller [8086:1e59] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] [8086:1e03] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation Panther Point SMBus Controller [8086:1e22] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel modules: i2c-i801 02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:8211] Kernel driver in use: rtl8192ce Kernel modules: rtl8192ce 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) Subsystem: Toshiba America Info Systems Device [1179:fb37] Kernel driver in use: r8169 Kernel modules: r8169 lsmod Module Size Used by snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 224066 1 joydev 17693 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 arc4 12529 2 snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq psmouse 87692 0 serio_raw 13211 0 rtl8192ce 84826 0 rtl8192c_common 75767 1 rtl8192ce rtlwifi 111202 1 rtl8192ce mac80211 506816 3 rtl8192ce,rtl8192c_common,rtlwifi snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device sparse_keymap 13890 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev mac_hid 13253 0 mei 41616 0 wmi 19256 0 soundcore 15091 1 snd i915 472941 3 snd_page_alloc 18529 2 snd_hda_intel,snd_pcm drm_kms_helper 46978 1 i915 cfg80211 205544 2 rtlwifi,mac80211 drm 242038 4 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 video 19596 1 i915 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 ums_realtek 18248 0 uas 18180 0 usb_storage 49198 1 ums_realtek dmesg | grep firmware [ 15.692951] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 16.240881] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 452.419288] rtl8192c_common:rtl92c_firmware_selfreset(): 8051 reset fail. [ 458.572211] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 465.440640] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 472.337617] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 479.175471] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 485.978582] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 492.764893] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 499.579348] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 506.386934] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 513.209545] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 519.991365] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 526.778375] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 533.629695] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 540.426004] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 547.238125] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 554.024434] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 560.854794] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 567.678160] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 574.494666] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 581.336653] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 588.157710] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 595.221122] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 602.047429] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 608.829534] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 615.639079] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 622.454991] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 629.273231] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 636.056613] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 642.858096] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 649.640753] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 657.184094] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 664.008018] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 670.838639] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 677.675418] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 684.507255] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 691.310994] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 698.095325] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 704.914509] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 711.725178] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin uname -r 3.2.0-29-generic ifconfig eth0 Link encap:Ethernet HWaddr 4c:72:b9:59:6c:61 inet addr:192.168.0.11 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::4e72:b9ff:fe59:6c61/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4447 errors:0 dropped:0 overruns:0 frame:0 TX packets:2762 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3671147 (3.6 MB) TX bytes:335133 (335.1 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:515 errors:0 dropped:0 overruns:0 frame:0 TX packets:515 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:83153 (83.1 KB) TX bytes:83153 (83.1 KB) wlan0 Link encap:Ethernet HWaddr 74:e5:43:32:47:95 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:280 errors:0 dropped:0 overruns:0 frame:0 TX packets:51 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:32958 (32.9 KB) TX bytes:10431 (10.4 KB)

  Read the article

• Oracle VM RAC template - what it took

  - by wcoekaer

  In my previous posting I introduced the latest Oracle Real Application Cluster / Oracle VM template. I mentioned how easy it is to deploy a complete Oracle RAC cluster with Oracle VM. In fact, you don't need any prior knowledge at all to get a complete production-ready setup going. Here is an example... I built a 4 node RAC cluster, completely configured in just over 40 minutes - starting from import template into Oracle VM, create VMs to fully up and running Oracle RAC. And what was needed? 1 textfile with some hostnames and ip addresses and deploycluster.py. The setup is a 4 node cluster where each VM has 8GB of RAM and 4 vCPUs. The shared ASM storage in this case is 100GB, 5 x 20GB volumes. The VM names are racovm.0-racovm.3. The deploycluster script starts the VMs, verifies the configuration and sends the database cluster configuration info through Oracle VM Manager to the 4 node VMs. Once the VMs are up and running, the first VM starts the actual Oracle RAC setup inside and talks to the 3 other VMs. I did not log into any VM until after everything was completed. In fact, I connected to the database remotely before logging in at all. # ./deploycluster.py -u admin -H localhost --vms racovm.0,racovm.1,racovm.2,racovm.3 --netconfig ./netconfig.ini Oracle RAC OneCommand (v1.1.0) for Oracle VM - deploy cluster - (c) 2011-2012 Oracle Corporation (com: 26700:v1.1.0, lib: 126247:v1.1.0, var: 1100:v1.1.0) - v2.4.3 - wopr8.wimmekes.net (x86_64) Invoked as root at Sat Jun 2 17:31:29 2012 (size: 37500, mtime: Wed May 16 00:13:19 2012) Using: ./deploycluster.py -u admin -H localhost --vms racovm.0,racovm.1,racovm.2,racovm.3 --netconfig ./netconfig.ini INFO: Login password to Oracle VM Manager not supplied on command line or environment (DEPLOYCLUSTER_MGR_PASSWORD), prompting... Password: INFO: Attempting to connect to Oracle VM Manager... INFO: Oracle VM Client (3.1.1.305) protocol (1.8) CONNECTED (tcp) to Oracle VM Manager (3.1.1.336) protocol (1.8) IP (192.168.1.40) UUID (0004fb0000010000cbce8a3181569a3e) INFO: Inspecting /root/rac/deploycluster/netconfig.ini for number of nodes defined... INFO: Detected 4 nodes in: /root/rac/deploycluster/netconfig.ini INFO: Located a total of (4) VMs; 4 VMs with a simple name of: ['racovm.0', 'racovm.1', 'racovm.2', 'racovm.3'] INFO: Verifying all (4) VMs are in Running state INFO: VM with a simple name of "racovm.0" is in a Stopped state, attempting to start it...OK. INFO: VM with a simple name of "racovm.1" is in a Stopped state, attempting to start it...OK. INFO: VM with a simple name of "racovm.2" is in a Stopped state, attempting to start it...OK. INFO: VM with a simple name of "racovm.3" is in a Stopped state, attempting to start it...OK. INFO: Detected that all (4) VMs specified on command have (5) common shared disks between them (ASM_MIN_DISKS=5) INFO: The (4) VMs passed basic sanity checks and in Running state, sending cluster details as follows: netconfig.ini (Network setup): /root/rac/deploycluster/netconfig.ini buildcluster: yes INFO: Starting to send cluster details to all (4) VM(s)....... INFO: Sending to VM with a simple name of "racovm.0".... INFO: Sending to VM with a simple name of "racovm.1"..... INFO: Sending to VM with a simple name of "racovm.2"..... INFO: Sending to VM with a simple name of "racovm.3"...... INFO: Cluster details sent to (4) VMs... Check log (default location /u01/racovm/buildcluster.log) on build VM (racovm.0)... INFO: deploycluster.py completed successfully at 17:32:02 in 33.2 seconds (00m:33s) Logfile at: /root/rac/deploycluster/deploycluster2.log my netconfig.ini # Node specific information NODE1=db11rac1 NODE1VIP=db11rac1-vip NODE1PRIV=db11rac1-priv NODE1IP=192.168.1.56 NODE1VIPIP=192.168.1.65 NODE1PRIVIP=192.168.2.2 NODE2=db11rac2 NODE2VIP=db11rac2-vip NODE2PRIV=db11rac2-priv NODE2IP=192.168.1.58 NODE2VIPIP=192.168.1.66 NODE2PRIVIP=192.168.2.3 NODE3=db11rac3 NODE3VIP=db11rac3-vip NODE3PRIV=db11rac3-priv NODE3IP=192.168.1.173 NODE3VIPIP=192.168.1.174 NODE3PRIVIP=192.168.2.4 NODE4=db11rac4 NODE4VIP=db11rac4-vip NODE4PRIV=db11rac4-priv NODE4IP=192.168.1.175 NODE4VIPIP=192.168.1.176 NODE4PRIVIP=192.168.2.5 # Common data PUBADAP=eth0 PUBMASK=255.255.255.0 PUBGW=192.168.1.1 PRIVADAP=eth1 PRIVMASK=255.255.255.0 RACCLUSTERNAME=raccluster DOMAINNAME=wimmekes.net DNSIP= # Device used to transfer network information to second node # in interview mode NETCONFIG_DEV=/dev/xvdc # 11gR2 specific data SCANNAME=db11vip SCANIP=192.168.1.57 last few lines of the in-VM log file : 2012-06-02 14:01:40:[clusterstate:Time :db11rac1] Completed successfully in 2 seconds (0h:00m:02s) 2012-06-02 14:01:40:[buildcluster:Done :db11rac1] Build 11gR2 RAC Cluster 2012-06-02 14:01:40:[buildcluster:Time :db11rac1] Completed successfully in 1779 seconds (0h:29m:39s) From start_vm to completely configured : 29m:39s. The other 10m was the import template and create 4 VMs from template along with the shared storage configuration. This consists of a complete Oracle 11gR2 RAC database with ASM, CRS and the RDBMS up and running on all 4 nodes. Simply connect and use. Production ready. Oracle on Oracle.

  Read the article

• Installing Ubuntu 12.04.1 x64 with Fake RAID 1 [SOLVED]

  - by Arkadius

  I had: Software: Dual boot with Windows XP Ubuntu 10.04 LTS x32 Hardware Fake RAID 1 (mirroring) with 2x1 TB: Partition 1 - Windows Partition 2 - SWAP Partition 3 - / (root) Partition 4 - Extended Partition 5 - /home Partition 6 - /data arek@domek:/var/log/installer$ sudo fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000de1b9 Device Boot Start End Blocks Id System /dev/sda1 * 63 524297339 262148638+ 7 HPFS/NTFS/exFAT /dev/sda2 524297340 528506369 2104515 82 Linux swap / Solaris /dev/sda3 528506370 570468149 20980890 83 Linux /dev/sda4 570468150 1953118439 691325145 5 Extended /dev/sda5 570468213 675340469 52436128+ 83 Linux /dev/sda6 675340533 1953118439 638888953+ 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000de1b9 Device Boot Start End Blocks Id System /dev/sdb1 * 63 524297339 262148638+ 7 HPFS/NTFS/exFAT /dev/sdb2 524297340 528506369 2104515 82 Linux swap / Solaris /dev/sdb3 528506370 570468149 20980890 83 Linux /dev/sdb4 570468150 1953118439 691325145 5 Extended /dev/sdb5 570468213 675340469 52436128+ 83 Linux /dev/sdb6 675340533 1953118439 638888953+ 83 Linux arek@domek:/var/log/installer$ ls -l /dev/mapper/ total 0 crw------- 1 root root 10, 236 Oct 7 20:17 control lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha -> ../dm-0 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha1 -> ../dm-1 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha2 -> ../dm-2 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha3 -> ../dm-3 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha4 -> ../dm-4 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha5 -> ../dm-5 lrwxrwxrwx 1 root root 7 Oct 7 20:17 pdc_jhjbcaha6 -> ../dm-6 I wanted to upgrade from 10.04 x32 to 12.04 x64 using FRESH installation. So, run installation of Ubuntu 12.04.1 x64 LTS using alternate CD. During the installation I selected manual partitioning and to: - Use and Format / (root) - Use and Format SWAP - Use and Keep data on /home - Use and Keep data on /data After I clicked "Continue" I get error creating and formatting SWAP partition. I go to terminal with Alt + F2 (?) and hit enter. I discovered that there was visible RAID as only disk with NO partitions. Something like this: arek@domek:/var/log/installer$ ls -l /dev/mapper/ lrwxrwxrwx 1 root root 7 Oct 7 20:17 /dev/mapper/pdc_jhjbcaha -> ../dm-0 arek@domek:/var/log/installer$ ls -l /dev/dm* brw-rw---- 1 root disk 252, 0 Oct 7 20:17 /dev/dm-0 So I switched to log console Alt+F3 (?) and saw errors like below: Oct 7 14:02:45 check-missing-firmware: /dev/.udev/firmware-missing does not exist, skipping Oct 7 14:02:45 check-missing-firmware: /run/udev/firmware-missing does not exist, skipping Oct 7 14:02:45 check-missing-firmware: no missing firmware in /dev/.udev/firmware-missing /run/udev/firmware-missing Oct 7 14:02:45 anna-install: Installing dmraid-udeb Oct 7 14:02:45 anna[12599]: DEBUG: retrieving dmraid-udeb 1.0.0.rc16-4.1ubuntu8 Oct 7 14:02:49 anna[12599]: DEBUG: retrieving libdmraid1.0.0.rc16-udeb 1.0.0.rc16-4.1ubuntu8 Oct 7 14:02:49 anna[12599]: DEBUG: retrieving kpartx-udeb 0.4.9-3ubuntu5 Oct 7 14:02:49 disk-detect: Serial ATA RAID disk(s) detected. Oct 7 14:02:55 disk-detect: Enabling dmraid support. Oct 7 14:02:55 disk-detect: RAID set "pdc_jhjbcaha" was activated Oct 7 14:02:55 HERE --> dmraid-activate: ERROR: Cannot retrieve RAID set information for pdc_jhjbcaha Oct 7 14:02:56 check-missing-firmware: /dev/.udev/firmware-missing does not exist, skipping Oct 7 14:02:56 check-missing-firmware: /run/udev/firmware-missing does not exist, skipping Oct 7 14:02:56 check-missing-firmware: no missing firmware in /dev/.udev/firmware-missing /run/udev/firmware-missing Oct 7 14:02:57 main-menu[428]: DEBUG: resolver (libnewt0.52): package doesn't exist (ignored) Oct 7 14:02:57 main-menu[428]: DEBUG: resolver (ext2-modules): package doesn't exist (ignored) Oct 7 14:02:57 main-menu[428]: INFO: Menu item 'partman-base' selected Oct 7 14:02:57 kernel: [ 316.512999] NTFS driver 2.1.30 [Flags: R/O MODULE]. Oct 7 14:02:57 kernel: [ 316.523221] Btrfs loaded Oct 7 14:02:57 kernel: [ 316.534781] JFS: nTxBlock = 8192, nTxLock = 65536 Oct 7 14:02:57 kernel: [ 316.554749] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled Oct 7 14:02:57 kernel: [ 316.555336] SGI XFS Quota Management subsystem Oct 7 14:02:58 md-devices: mdadm: No arrays found in config file or automatically Oct 7 14:02:58 partman: No matching physical volumes found Oct 7 14:02:58 partman: No volume groups found Oct 7 14:02:58 partman: Reading all physical volumes. This may take a while... Oct 7 14:02:58 partman-lvm: No volume groups found Oct 7 14:02:58 partman: Error running 'tune2fs -l /dev/mapper/pdc_jhjbcaha' Oct 7 14:02:58 partman: Error running 'tune2fs -l /dev/mapper/pdc_jhjbcaha' Oct 7 14:02:58 partman: Error running 'tune2fs -l /dev/mapper/pdc_jhjbcaha' Oct 7 14:06:11 HERE --> partman: mkswap: can't open '/dev/mapper/pdc_jhjbcaha2': No such file or directory Oct 7 14:07:28 init: starting pid 401, tty '/dev/tty2': '-/bin/sh' Oct 7 14:15:00 net/hw-detect.hotplug: Detected hotpluggable network interface eth0 Oct 7 14:15:00 net/hw-detect.hotplug: Detected hotpluggable network interface lo As You can see there are 2 errors Oct 7 14:02:55 dmraid-activate: ERROR: Cannot retrieve RAID set information for pdc_jhjbcaha and Oct 7 14:06:11 partman: mkswap: can't open '/dev/mapper/pdc_jhjbcaha2': No such file or directory I looked in the internet and try to run command "dmraid -ay" and get something like that: dmraid -ay /dev/mapper/pdc_jhjbcaha -> Already activated /dev/mapper/pdc_jhjbcaha1 -> Successfully activated /dev/mapper/pdc_jhjbcaha2 -> Successfully activated /dev/mapper/pdc_jhjbcaha3 -> Successfully activated /dev/mapper/pdc_jhjbcaha4 -> Successfully activated /dev/mapper/pdc_jhjbcaha5 -> Successfully activated /dev/mapper/pdc_jhjbcaha6 -> Successfully activated Then I returned to installer with Alt+F1 (?) and click "Return" to return to partitioning menu. I did NOT change anything just selected again "Continue" and everything goes smoothly. I hope this will help someone. arkadius

  Read the article

• Atheros AR2413 wireless not working after shutdown

  - by Chandrasekhar

  I am using a Ubuntu 11.04 on an Acer aspire 3680 laptop and my wifi is not working. I followed the below commands to install the madwifi driver: sudo su apt-get install subversion cd /usr/src svn checkout http://madwifi-project.org/svn/madwifi/trunk madwifi tar cfvz madwifi.tgz cd madwifi make && make install echo "blacklist ath5k" /etc/modprobe.d/blacklist.conf echo "ath_pci" /etc/modules modprobe ath_pci sudo reboot After installation I am facing the same problem. My wifi wont work after I shutdown. Infact it didn't work after suspend but I rectified that problem by the following commands: Command 1: sudo rmmod -f ath_pci sudo rfkill unblock all sudo modprobe ath_pci along with the command SUSPEND_MODULES=ath_pci added to the /etc/pm/config.d/madwifi directory. So if I suspend and then on my laptop the wifi loads well and doesn't create a problem. But if I shutdown my laptop the wifi never loads again and eachtime I have to run a Ubuntu 9.04 live CD to load it. I did try adding the Command 1 to the /etc/rc.local directory but still it doesn't work. So my question is: What should I do in order to make my wireless work without having to run a live CD of ubuntu 9.04 everytime after shutdown? Thanks. Here are the outputs which one might need: Output 1 chandru@chandru-acer:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 0a:03.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) 0a:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) Output 2: lsmod Module Size Used by wlan_tkip 17074 2 binfmt_misc 13213 1 parport_pc 32111 0 ppdev 12849 0 snd_hda_codec_si3054 12924 1 snd_hda_codec_realtek 255882 1 joydev 17322 0 snd_atiixp_modem 18624 0 snd_via82xx_modem 18305 0 snd_intel8x0m 18493 0 snd_ac97_codec 105614 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m snd_hda_intel 24113 2 ac97_bus 12642 1 snd_ac97_codec snd_hda_codec 90901 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel i915 451053 3 snd_hwdep 13274 1 snd_hda_codec snd_pcm 80042 7 snd_hda_codec_si3054,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25269 1 snd_seq_midi drm_kms_helper 40971 1 i915 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event pcmcia 39671 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq drm 184164 4 i915,drm_kms_helper yenta_socket 27230 0 tifm_7xx1 12898 0 wlan_scan_sta 21945 1 ath_rate_sample 17279 1 pcmcia_rsrc 18292 1 yenta_socket psmouse 73312 0 tifm_core 15040 1 tifm_7xx1 snd 55295 18 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device serio_raw 12990 0 i2c_algo_bit 13184 1 i915 soundcore 12600 1 snd pcmcia_core 21505 3 pcmcia,yenta_socket,pcmcia_rsrc video 19112 1 i915 ath_pci 183044 0 snd_page_alloc 14073 5 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci lp 13349 0 parport 36746 3 parport_pc,ppdev,lp usbhid 41704 0 hid 77084 1 usbhid sky2 49172 0 Output 3 root@chandru-acer:~# lshw -C network PCI (sysfs) *-network description: Ethernet interface product: 88E8038 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 14 serial: 00:16:36:fb:aa:64 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.28 firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:44000000-44003fff ioport:2000(size=256) *-network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wifi0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci ip=192.168.1.6 latency=96 maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11g resources: irq:18 memory:d0000000-d000ffff Output 4 root@chandru-acer:~# lsmod | grep ath_pci ath_pci 183044 0 wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci

  Read the article

• Rewriting Live TCP/IP (Layer 4) (i.e. Socket Layer) Streams

  - by user213060

  I have a simple problem which I'm sure someone here has done before... I want to rewrite Layer 4 TCP/IP streams (Not lower layer individual packets or frames.) Ettercap's etterfilter command lets you perform simple live replacements of Layer 4 TCP/IP streams based on fixed strings or regexes. Example ettercap scripting code: if (ip.proto == TCP && tcp.dst == 80) { if (search(DATA.data, "gzip")) { replace("gzip", " "); msg("whited out gzip\n"); } } if (ip.proto == TCP && tcp.dst == 80) { if (search(DATA.data, "deflate")) { replace("deflate", " "); msg("whited out deflate\n"); } } http://ettercap.sourceforge.net/forum/viewtopic.php?t=2833 I would like to rewrite streams based on my own filter program instead of just simple string replacements. Anyone have an idea of how to do this? Is there anything other than Ettercap that can do live replacement like this, maybe as a plugin to a VPN software or something? I would like to have a configuration similar to ettercap's silent bridged sniffing configuration between two Ethernet interfaces. This way I can silently filter traffic coming from either direction with no NATing problems. Note that my filter is an application that acts as a pipe filter, similar to the design of unix command-line filters: >[eth0] <----------> [my filter] <----------> [eth1]< What I am already aware of, but are not suitable: Tun/Tap - Works at the lower packet layer, I need to work with the higher layer streams. Ettercap - I can't find any way to do replacements other than the restricted capabilities in the example above. Hooking into some VPN software? - I just can't figure out which or exactly how. libnetfilter_queue - Works with lower layer packets, not TCP/IP streams. Again, the rewriting should occur at the transport layer (Layer 4) as it does in this example, instead of a lower layer packet-based approach. Exact code will help immensely! Thanks!

  Read the article

• how to allow certain packet with certian destination ports to forward using iptables?

  - by moataz metwally

  i have server and i virualized it into multiple windws vps's using kvm. i would like to make all vps behind the server firewall. to control all the ports of all vps's from the host server.i have tried to do this by that iptables file but it still blocking all the forward packets. when i remove -A FORWARD -j DROP from the file the vps will be out of the firewall control : # Generated by iptables-save v1.4.7 on Mon Oct 21 04:30:35 2013 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [49:7546] -A OUTPUT -j ACCEPT -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j DROP -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp -m multiport --dports 5901:6010,4080:4085 -j ACCEPT -A FORWARD -p tcp -s 0/0 -d 0/0 --destination-port 3389 -j ACCEPT -A INPUT -j DROP -A FORWARD -j DROP COMMIT # Completed on Mon Oct 21 04:30:35 2013 and my ifconfig output: eth0 Link encap:Ethernet HWaddr 6C:62:6D:EF:B8:77 inet6 addr: fe80::6e62:XXX:feef:b877/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4460000 errors:0 dropped:0 overruns:0 frame:0 TX packets:1825697 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5461498823 (5.0 GiB) TX bytes:547852516 (522.4 MiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6380 errors:0 dropped:0 overruns:0 frame:0 TX packets:6380 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6481652 (6.1 MiB) TX bytes:6481652 (6.1 MiB) natbr2 Link encap:Ethernet HWaddr 52:54:00:48:72:53 inet addr:88.XXX.XXX.X53 Bcast:88.198.242.159 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1338720 errors:0 dropped:0 overruns:0 frame:0 TX packets:3570844 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:434791198 (414.6 MiB) TX bytes:4321751647 (4.0 GiB) viif1001 Link encap:Ethernet HWaddr FE:16:3E:0F:41:D8 inet6 addr: fe80::fc16:XXX:fe0f:41d8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:358229 errors:0 dropped:0 overruns:0 frame:0 TX packets:479289 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:50127351 (47.8 MiB) TX bytes:261223068 (249.1 MiB) viif1002 Link encap:Ethernet HWaddr FE:16:3E:EA:65:FA inet6 addr: fe80::fc16:XXX:feea:65fa/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:575590 errors:0 dropped:0 overruns:0 frame:0 TX packets:1489296 errors:0 dropped:0 overruns:5412 carrier:0 collisions:0 txqueuelen:500 RX bytes:243629668 (232.3 MiB) TX bytes:1724640936 (1.6 GiB) viif1003 Link encap:Ethernet HWaddr FE:16:3E:2B:85:0E inet6 addr: fe80::fc16:XXX:fe2b:850e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:413052 errors:0 dropped:0 overruns:0 frame:0 TX packets:1741801 errors:0 dropped:0 overruns:299 carrier:0 collisions:0 txqueuelen:500 RX bytes:147931054 (141.0 MiB) TX bytes:2338132498 (2.1 GiB) viifbr0 Link encap:Ethernet HWaddr 6C:62:6D:EF:B8:77 inet addr:176.XX.XX.X9 Bcast:176.9.0.95 Mask:255.255.255.224 inet6 addr: fe80::6e62:XXX:feef:b877/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2685666 errors:0 dropped:0 overruns:0 frame:0 TX packets:1472089 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4244043694 (3.9 GiB) TX bytes:523110523 (498.8 MiB)

  Read the article

• Linux fsck.ext3 says "Device or resource busy" although I did not mount the disk.

  - by matnagel

  I am running an ubuntu 8.04 server instance with a 8GB virtual disk on vmware 1.0.9. For disk maintenance I made a copy of the virtual disk (by making a copy of the 2 vmdk files of sda on the stopped vm on the host) and added it to the original vm. Now this vm has it's original virtual disk sda plus a 1:1 copy (sdd). There are 2 additional disk sdb and sdc which I ignore.) I would expect sdb not to be mounted when I start the vm. So I try tp do a ext2 fsck on sdd from the running vm, but it reports fsck reported that sdb was mounted. $ sudo fsck.ext3 -b 8193 /dev/sdd e2fsck 1.40.8 (13-Mar-2008) fsck.ext3: Device or resource busy while trying to open /dev/sdd Filesystem mounted or opened exclusively by another program? The "mount" command does not tell me sdd is mounted: $ sudo mount /dev/sda1 on / type ext3 (rw,relatime,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) /sys on /sys type sysfs (rw,noexec,nosuid,nodev) varrun on /var/run type tmpfs (rw,noexec,nosuid,nodev,mode=0755) varlock on /var/lock type tmpfs (rw,noexec,nosuid,nodev,mode=1777) udev on /dev type tmpfs (rw,mode=0755) devshm on /dev/shm type tmpfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) /dev/sdc1 on /mnt/r1 type ext3 (rw,relatime,errors=remount-ro) /dev/sdb1 on /mnt/k1 type ext3 (rw,relatime,errors=remount-ro) securityfs on /sys/kernel/security type securityfs (rw) When I ignore the warning and continue the fsck, it reported many errors. How do I get this under control? Is there a better way to figure out if sdd is mounted? Or how is it "busy? How to unmount it then? How to prevent ubuntu from automatically mounting. Or is there something else I am missing? Also from /var/log/syslog I cannot see it is mounted, this is the last part of the startup sequence: kernel: [ 14.229494] ACPI: Power Button (FF) [PWRF] kernel: [ 14.230326] ACPI: AC Adapter [ACAD] (on-line) kernel: [ 14.460136] input: PC Speaker as /devices/platform/pcspkr/input/input3 kernel: [ 14.639366] udev: renamed network interface eth0 to eth1 kernel: [ 14.670187] eth1: link up kernel: [ 16.329607] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/ kernel: [ 16.367540] parport_pc 00:08: reported by Plug and Play ACPI kernel: [ 16.367670] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] kernel: [ 19.425637] NET: Registered protocol family 10 kernel: [ 19.437550] lo: Disabled Privacy Extensions kernel: [ 24.328857] loop: module loaded kernel: [ 24.449293] lp0: using parport0 (interrupt-driven). kernel: [ 26.075499] EXT3 FS on sda1, internal journal kernel: [ 28.380299] kjournald starting. Commit interval 5 seconds kernel: [ 28.381706] EXT3 FS on sdc1, internal journal kernel: [ 28.381747] EXT3-fs: mounted filesystem with ordered data mode. kernel: [ 28.444867] kjournald starting. Commit interval 5 seconds kernel: [ 28.445436] EXT3 FS on sdb1, internal journal kernel: [ 28.445444] EXT3-fs: mounted filesystem with ordered data mode. kernel: [ 31.309766] eth1: no IPv6 routers present kernel: [ 35.054268] ip_tables: (C) 2000-2006 Netfilter Core Team mysqld_safe[4367]: started mysqld[4370]: 100124 14:40:21 InnoDB: Started; log sequence number 0 10130914 mysqld[4370]: 100124 14:40:21 [Note] /usr/sbin/mysqld: ready for connections. mysqld[4370]: Version: '5.0.51a-3ubuntu5.4' socket: '/var/run/mysqld/mysqld.sock' port: 3 /etc/mysql/debian-start[4417]: Upgrading MySQL tables if necessary. /etc/mysql/debian-start[4422]: Looking for 'mysql' in: /usr/bin/mysql /etc/mysql/debian-start[4422]: Looking for 'mysqlcheck' in: /usr/bin/mysqlcheck /etc/mysql/debian-start[4422]: This installation of MySQL is already upgraded to 5.0.51a, u /etc/mysql/debian-start[4436]: Checking for insecure root accounts. /etc/mysql/debian-start[4444]: Checking for crashed MySQL tables.

  Read the article

• dns queries not using nscd for caching

  - by xenoterracide

  I'm trying to use nscd (Nameservices Cache Daemon) to cache dns locally so I can stop using bind to do it. I've gotten it started and ntpd seems to attempt to use it. But everything else for hosts seems to ignore it. e.g if I do dig apache.org 3 times none of them will hit the cache. I'm viewing the cache stats using nscd -g to determine whether it's been used. I've also turned the debug log level up to see if I can see it hitting and the queries don't even hit nscd. nsswitch.conf # Begin /etc/nsswitch.conf passwd: files group: files shadow: files publickey: files hosts: cache files dns networks: files protocols: files services: files ethers: files rpc: files netgroup: files # End /etc/nsswitch.confenter code here nscd.conf # # /etc/nscd.conf # # An example Name Service Cache config file. This file is needed by nscd. # # Legal entries are: # # logfile <file> # debug-level <level> # threads <initial #threads to use> # max-threads <maximum #threads to use> # server-user <user to run server as instead of root> # server-user is ignored if nscd is started with -S parameters # stat-user <user who is allowed to request statistics> # reload-count unlimited|<number> # paranoia <yes|no> # restart-interval <time in seconds> # # enable-cache <service> <yes|no> # positive-time-to-live <service> <time in seconds> # negative-time-to-live <service> <time in seconds> # suggested-size <service> <prime number> # check-files <service> <yes|no> # persistent <service> <yes|no> # shared <service> <yes|no> # max-db-size <service> <number bytes> # auto-propagate <service> <yes|no> # # Currently supported cache names (services): passwd, group, hosts, services # logfile /var/log/nscd.log threads 4 max-threads 32 server-user nobody # stat-user somebody debug-level 9 # reload-count 5 paranoia no # restart-interval 3600 enable-cache passwd yes positive-time-to-live passwd 600 negative-time-to-live passwd 20 suggested-size passwd 211 check-files passwd yes persistent passwd yes shared passwd yes max-db-size passwd 33554432 auto-propagate passwd yes enable-cache group yes positive-time-to-live group 3600 negative-time-to-live group 60 suggested-size group 211 check-files group yes persistent group yes shared group yes max-db-size group 33554432 auto-propagate group yes enable-cache hosts yes positive-time-to-live hosts 3600 negative-time-to-live hosts 20 suggested-size hosts 211 check-files hosts yes persistent hosts yes shared hosts yes max-db-size hosts 33554432 enable-cache services yes positive-time-to-live services 28800 negative-time-to-live services 20 suggested-size services 211 check-files services yes persistent services yes shared services yes max-db-size services 33554432 resolv.conf # Generated by dhcpcd from eth0 nameserver 127.0.0.1 domain westell.com nameserver 192.168.1.1 nameserver 208.67.222.222 nameserver 208.67.220.220 as kind of a side note I'm using archlinux.

  Read the article

• iptables not allowing mysql connections to aliased ips?

  - by Curtis

  I have a fairly simple iptables firewall on a server that provides MySQL services, but iptables seems to be giving me very inconsistent results. The default policy on the script is as follows: iptables -P INPUT DROP I can then make MySQL public with the following rule: iptables -A INPUT -p tcp --dport 3306 -j ACCEPT With this rule in place, I can connect to MySQL from any source IP to any destination IP on the server without a problem. However, when I try to restrict access to just three IPs by replacing the above line with the following, I run into trouble (xxx=masked octect): iptables -A INPUT -p tcp --dport 3306 -m state --state NEW -s 208.XXX.XXX.184 -j ACCEPT iptables -A INPUT -p tcp --dport 3306 -m state --state NEW -s 208.XXX.XXX.196 -j ACCEPT iptables -A INPUT -p tcp --dport 3306 -m state --state NEW -s 208.XXX.XXX.251 -j ACCEPT Once the above rules are in place, the following happens: I can connect to the MySQL server from the .184, .196 and .251 hosts just fine as long as am connecting to the MySQL server using it's default IP address or an IP alias in the same subnet as the default IP address. I am unable to connect to MySQL using IP aliases that are assigned to the server from a different subnet than the server's default IP when I'm coming from the .184 or .196 hosts, but .251 works just fine. From the .184 or .196 hosts, a telnet attempt just hangs... # telnet 209.xxx.xxx.22 3306 Trying 209.xxx.xxx.22... If I remove the .251 line (making .196 the last rule added), the .196 host still can not connect to MySQL using IP aliases (so it's not the order of the rules that is causing the inconsistent behavior). I know, this particular test was silly as it shouldn't matter what order these three rules are added in, but I figured someone might ask. If I switch back to the "public" rule, all hosts can connect to the MySQL server using either the default or aliased IPs (in either subnet): iptables -A INPUT -p tcp --dport 3306 -j ACCEPT The server is running in a CentOS 5.4 OpenVZ/Proxmox container (2.6.32-4-pve). And, just in case you prefer to see the problem rules in the context of the iptables script, here it is (xxx=masked octect): # Flush old rules, old custom tables /sbin/iptables --flush /sbin/iptables --delete-chain # Set default policies for all three default chains /sbin/iptables -P INPUT DROP /sbin/iptables -P FORWARD DROP /sbin/iptables -P OUTPUT ACCEPT # Enable free use of loopback interfaces /sbin/iptables -A INPUT -i lo -j ACCEPT /sbin/iptables -A OUTPUT -o lo -j ACCEPT # All TCP sessions should begin with SYN /sbin/iptables -A INPUT -p tcp ! --syn -m state --state NEW -j DROP # Accept inbound TCP packets (Do this *before* adding the 'blocked' chain) /sbin/iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow the server's own IP to connect to itself /sbin/iptables -A INPUT -i eth0 -s 208.xxx.xxx.178 -j ACCEPT # Add the 'blocked' chain *after* we've accepted established/related connections # so we remain efficient and only evaluate new/inbound connections /sbin/iptables -N BLOCKED /sbin/iptables -A INPUT -j BLOCKED # Accept inbound ICMP messages /sbin/iptables -A INPUT -p ICMP --icmp-type 8 -j ACCEPT /sbin/iptables -A INPUT -p ICMP --icmp-type 11 -j ACCEPT # ssh (private) /sbin/iptables -A INPUT -p tcp --dport 22 -m state --state NEW -s xxx.xxx.xxx.xxx -j ACCEPT # ftp (private) /sbin/iptables -A INPUT -p tcp --dport 21 -m state --state NEW -s xxx.xxx.xxx.xxx -j ACCEPT # www (public) /sbin/iptables -A INPUT -p tcp --dport 80 -j ACCEPT /sbin/iptables -A INPUT -p tcp --dport 443 -j ACCEPT # smtp (public) /sbin/iptables -A INPUT -p tcp --dport 25 -j ACCEPT /sbin/iptables -A INPUT -p tcp --dport 2525 -j ACCEPT # pop (public) /sbin/iptables -A INPUT -p tcp --dport 110 -j ACCEPT # mysql (private) /sbin/iptables -A INPUT -p tcp --dport 3306 -m state --state NEW -s 208.xxx.xxx.184 -j ACCEPT /sbin/iptables -A INPUT -p tcp --dport 3306 -m state --state NEW -s 208.xxx.xxx.196 -j ACCEPT /sbin/iptables -A INPUT -p tcp --dport 3306 -m state --state NEW -s 208.xxx.xxx.251 -j ACCEPT Any ideas? Thanks in advance. :-)

  Read the article

• Randomly displayed flashing lines, no response to all shortcuts, just power off. [syslog included]

  - by B. Roland

  Hello! I have an old machine, and I want to use for that to learn employees how to use Ubuntu, and to be easyer to switch from Windows. I've been installed 10.04, and updated, but this strange stuff is happend. Graphical installion failed, same strange thing. With alternate workd. Sometimes, when I boot up, a boot message displayed: Keyboard failure..., often diplayed after reboot, and after shutdown, when I haven't plugged off from AC. I replaced the keyboard yet, same failure... If I powered off, and plugged off from AC, no keyboard problems displayed in boot time. Details Configuration: Dell OptiPlex GX60 - in original cover, no changes. 256 MB DDR 166 MHz Intel® Celeron® Processor 2.40 GHz Dell 0C3207 Base Board I know, that is not enough, but I have three other Nec compuers, with nearly similar config, and they works well with 9.10, 10.04, 10.10. Live CDs I've been tried with 10.04 and 10.10, but the problem is displayed too. With 9.10 no strange things displayed, but it froze, during a simple apt-get install. Syslog An error loop is logged here, but I paste the whole startup and error lines. The flashing lines are displayed sometimes immediately after login, but sometimes after 10 minutes, but once occured, that nothing happend. Strange thing is displayed immediately after login: here. An other boot, after some minutes, strange lines, and loop in log appeard: here. The loop should be that: Jan 23 00:20:08 machine_name kernel: [ 46.782212] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 23 00:20:08 machine_name kernel: [ 47.100033] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 23 00:20:08 machine_name kernel: [ 47.100045] render error detected, EIR: 0x00000000 Jan 23 00:20:08 machine_name kernel: [ 47.101487] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 16 at 9) Jan 23 00:20:11 machine_name kernel: [ 49.152020] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 23 00:20:11 machine_name gdm-simple-slave[1245]: WARNING: Unable to load file '/etc/gdm/custom.conf': No such file or directory Jan 23 00:20:11 machine_name acpid: client 1239[0:0] has disconnected Jan 23 00:20:11 machine_name acpid: client connected from 1247[0:0] Jan 23 00:20:11 machine_name acpid: 1 client rule loaded UPDATE Added syslog things: before errors, error loop, the complete shutdown(after the big updates): Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully called chroot. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully dropped privileges. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully limited resources. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Watchdog thread running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Canary thread running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully made thread 1337 of process 1337 (n/a) owned by '1001' high priority at nice level -11. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Supervising 1 threads of 1 processes of 1 users. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Sucessfully made thread 1345 of process 1337 (n/a) owned by '1001' RT at priority 5. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Supervising 2 threads of 1 processes of 1 users. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Sucessfully made thread 1349 of process 1337 (n/a) owned by '1001' RT at priority 5. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Supervising 3 threads of 1 processes of 1 users. Jan 28 20:40:37 machine_name pulseaudio[1337]: ratelimit.c: 2 events suppressed Jan 28 20:41:33 machine_name AptDaemon: INFO: Initializing daemon Jan 28 20:41:44 machine_name kernel: [ 167.691563] lo: Disabled Privacy Extensions Jan 28 20:47:33 machine_name AptDaemon: INFO: Quiting due to inactivity Jan 28 20:47:33 machine_name AptDaemon: INFO: Shutdown was requested Jan 28 20:59:50 machine_name kernel: [ 1253.840513] lo: Disabled Privacy Extensions Jan 28 21:17:02 machine_name CRON[1874]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jan 28 21:17:38 machine_name kernel: [ 2321.553239] lo: Disabled Privacy Extensions Jan 28 22:07:44 machine_name kernel: [ 5327.840254] lo: Disabled Privacy Extensions Jan 28 22:17:02 machine_name CRON[2665]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: Called Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: username = [some_user] Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: /home/some_user is already mounted Jan 28 22:57:03 machine_name kernel: [ 8286.641472] lo: Disabled Privacy Extensions Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: Called Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: username = [some_user] Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: /home/some_user is already mounted Jan 28 23:07:42 machine_name kernel: [ 8925.272030] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:07:42 machine_name kernel: [ 8925.272048] render error detected, EIR: 0x00000000 Jan 28 23:07:42 machine_name kernel: [ 8925.272093] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171453 at 171452) Jan 28 23:07:45 machine_name kernel: [ 8928.868041] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 28 23:08:10 machine_name acpid: client 925[0:0] has disconnected Jan 28 23:08:10 machine_name acpid: client connected from 8127[0:0] Jan 28 23:08:10 machine_name acpid: 1 client rule loaded Jan 28 23:08:11 machine_name kernel: [ 8955.046248] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 28 23:08:12 machine_name kernel: [ 8955.364016] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:08:12 machine_name kernel: [ 8955.364027] render error detected, EIR: 0x00000000 Jan 28 23:08:12 machine_name kernel: [ 8955.364407] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171457 at 171452) Jan 28 23:08:14 machine_name kernel: [ 8957.472025] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 28 23:08:14 machine_name acpid: client 8127[0:0] has disconnected Jan 28 23:08:14 machine_name acpid: client connected from 8141[0:0] Jan 28 23:08:14 machine_name acpid: 1 client rule loaded Jan 28 23:08:15 machine_name kernel: [ 8958.671722] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 28 23:08:15 machine_name kernel: [ 8958.988015] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:08:15 machine_name kernel: [ 8958.988026] render error detected, EIR: 0x00000000 Jan 28 23:08:15 machine_name kernel: [ 8958.989400] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171459 at 171452) Jan 28 23:08:16 machine_name init: tty4 main process (848) killed by TERM signal Jan 28 23:08:16 machine_name init: tty5 main process (856) killed by TERM signal Jan 28 23:08:16 machine_name NetworkManager: nm_signal_handler(): Caught signal 15, shutting down normally. Jan 28 23:08:16 machine_name init: tty2 main process (874) killed by TERM signal Jan 28 23:08:16 machine_name init: tty3 main process (875) killed by TERM signal Jan 28 23:08:16 machine_name init: tty6 main process (877) killed by TERM signal Jan 28 23:08:16 machine_name init: cron main process (890) killed by TERM signal Jan 28 23:08:16 machine_name init: tty1 main process (1146) killed by TERM signal Jan 28 23:08:16 machine_name avahi-daemon[644]: Got SIGTERM, quitting. Jan 28 23:08:16 machine_name avahi-daemon[644]: Leaving mDNS multicast group on interface eth0.IPv4 with address 10.238.11.134. Jan 28 23:08:16 machine_name acpid: exiting Jan 28 23:08:16 machine_name init: avahi-daemon main process (644) terminated with status 255 Jan 28 23:08:17 machine_name kernel: Kernel logging (proc) stopped. Jan 28 23:09:00 machine_name kernel: imklog 4.2.0, log source = /proc/kmsg started. Jan 28 23:09:00 machine_name rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="516" x-info="http://www.rsyslog.com"] (re)start Jan 28 23:09:00 machine_name rsyslogd: rsyslogd's groupid changed to 103 Jan 28 23:09:00 machine_name rsyslogd: rsyslogd's userid changed to 101 Jan 28 23:09:00 machine_name rsyslogd-2039: Could no open output file '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ] When I hit the On/Off button, the system shuts down normally. May be it a hardware problem, but I don't know... Can you say something useful to solve my problem?

  Read the article

• SATA drive problems with two SIL RAID cards

  - by Jon Topper

  I've just put a second SiI 3114 SATARaid card in my home server so that I could add another pair of SATA drives and increase my storage space. Annoyingly, it doesn't seem to work: [ 32.816030] ata5: lost interrupt (Status 0x0) [ 32.816072] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 32.816091] ata5.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in [ 32.816094] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 32.816101] ata5.00: status: { DRDY } [ 32.816117] ata5: hard resetting link [ 33.136082] ata5: SATA link down (SStatus 0 SControl 0) [ 36.060940] irq 18: nobody cared (try booting with the "irqpoll" option) [ 36.060949] Pid: 0, comm: swapper Not tainted 2.6.31-20-generic #58-Ubuntu [ 36.060954] Call Trace: [ 36.060977] [] ? printk+0x18/0x1c [ 36.060997] [] __report_bad_irq+0x27/0x90 [ 36.061005] [] note_interrupt+0x150/0x190 [ 36.061011] [] handle_fasteoi_irq+0xac/0xd0 [ 36.061023] [] handle_irq+0x18/0x30 [ 36.061029] [] do_IRQ+0x47/0xc0 [ 36.061042] [] ? irq_exit+0x50/0x70 [ 36.061058] [] ? smp_apic_timer_interrupt+0x57/0x90 [ 36.061065] [] common_interrupt+0x30/0x40 [ 36.061075] [] ? native_safe_halt+0x5/0x10 [ 36.061082] [] default_idle+0x46/0xd0 [ 36.061088] [] cpu_idle+0x8c/0xd0 [ 36.061103] [] rest_init+0x55/0x60 [ 36.061111] [] start_kernel+0x2e6/0x2ec [ 36.061117] [] ? unknown_bootoption+0x0/0x19e [ 36.061133] [] i386_start_kernel+0x7c/0x83 [ 36.061137] handlers: [ 36.061139] [] (sil_interrupt+0x0/0xb0) [ 36.061151] Disabling IRQ #18 [ 38.136014] ata5: hard resetting link [ 38.456022] ata5: SATA link down (SStatus 0 SControl 0) [ 43.456013] ata5: hard resetting link [ 43.776022] ata5: SATA link down (SStatus 0 SControl 0) [ 43.776035] ata5.00: disabled [ 43.776055] ata5.00: device reported invalid CHS sector 0 [ 43.776074] sd 4:0:0:0: [sde] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 43.776082] sd 4:0:0:0: [sde] Sense Key : Aborted Command [current] [descriptor] [ 43.776092] Descriptor sense data with sense descriptors (in hex): [ 43.776097] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 [ 43.776112] 00 00 00 00 [ 43.776118] sd 4:0:0:0: [sde] Add. Sense: No additional sense information [ 43.776127] end_request: I/O error, dev sde, sector 0 [ 43.776136] Buffer I/O error on device sde, logical block 0 [ 43.776170] ata5: EH complete [ 43.776187] ata5.00: detaching (SCSI 4:0:0:0) root@core:~# cat /proc/interrupts CPU0 0: 47 IO-APIC-edge timer 1: 8 IO-APIC-edge i8042 6: 3 IO-APIC-edge floppy 7: 0 IO-APIC-edge parport0 8: 0 IO-APIC-edge rtc0 9: 0 IO-APIC-fasteoi acpi 14: 53069 IO-APIC-edge pata_sis 15: 53004 IO-APIC-edge pata_sis 17: 112265 IO-APIC-fasteoi sata_sil 18: 200002 IO-APIC-fasteoi sata_sil, SiS SI7012 19: 111140 IO-APIC-fasteoi eth0 20: 0 IO-APIC-fasteoi ohci_hcd:usb2 21: 0 IO-APIC-fasteoi ohci_hcd:usb3 23: 0 IO-APIC-fasteoi ehci_hcd:usb1 NMI: 0 Non-maskable interrupts LOC: 6650492 Local timer interrupts SPU: 0 Spurious interrupts CNT: 0 Performance counter interrupts PND: 0 Performance pending work RES: 0 Rescheduling interrupts CAL: 0 Function call interrupts TLB: 0 TLB shootdowns TRM: 0 Thermal event interrupts THR: 0 Threshold APIC interrupts MCE: 0 Machine check exceptions MCP: 160 Machine check polls ERR: 0 MIS: 0 root@core:~# lspci | grep Raid 00:09.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) 00:0a.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) root@core:~# lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 9.10 Release: 9.10 Codename: karmic root@core:~# uname -a Linux core.topper.me.uk 2.6.31-20-generic #58-Ubuntu SMP Fri Mar 12 05:23:09 UTC 2010 i686 GNU/Linux I've tried a combination of different kernel options (irqpoll, noapic, noacpi, pci=noapic) all to no avail. Does anyone have any bright ideas about how I can go about making this work? Swapping PCI cards around isn't an option as there are only two slots in this motherboard (an ASRock K7S41GX). The BIOS doesn't look to have too much in the way of configuration options regarding IRQ usage. Plan B is to ditch this server completely and buy a new QNAP for these drives to go in, but I was hoping to avoid doing this right now.

  Read the article

• routing specific IP to ppp0 tunnel

  - by gompertz

  Hi All, I feel I've struggled with this long enough and need some help. I have a pptp tunnel and am trying to route destination traffic from 208.85.40.20 to the pptp tunnel (ppp0). (Keen observers may recognize the ip as being that of pandora.com). I am doing all this configuration on a router... and I know it's not working successfully as traceroute yields nothing but astericks. I've pasted relevant outputs below: (with some "security" editing to the addresses) root@OpenWrt:~# ifconfig br0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28185 errors:0 dropped:0 overruns:0 frame:0 TX packets:24936 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4894242 (4.6 MiB) TX bytes:5941902 (5.6 MiB) eth0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:51829 errors:0 dropped:0 overruns:0 frame:0 TX packets:56824 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:11490288 (10.9 MiB) TX bytes:11857913 (11.3 MiB) Interrupt:4 eth2 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:15426 TX packets:9529 errors:21 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:423 (423.0 B) TX bytes:596036 (582.0 KiB) Interrupt:2 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:30 errors:0 dropped:0 overruns:0 frame:0 TX packets:30 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2300 (2.2 KiB) TX bytes:2300 (2.2 KiB) ppp0 Link encap:Point-Point Protocol inet addr:68.68.39.250 P-t-P:172.16.20.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:165 errors:2 dropped:0 overruns:0 frame:0 TX packets:68 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:7006 (6.8 KiB) TX bytes:3462 (3.3 KiB) vlan0 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:28182 errors:0 dropped:0 overruns:0 frame:0 TX packets:33813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5006544 (4.7 MiB) TX bytes:6609774 (6.3 MiB) vlan1 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX inet addr:173.183.111.3 Bcast:173.183.111.255 Mask:255.255.224.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:23653 errors:0 dropped:0 overruns:0 frame:0 TX packets:23012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5522012 (5.2 MiB) TX bytes:4982944 (4.7 MiB) wds0.4915 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wds0.4915 Link encap:Ethernet HWaddr 00:1A:92:BC:XX:XX UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@OpenWrt:~# cat /etc/ppp/ip-up iptables -A FORWARD -t filter -i br0 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -t filter -i ppp0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o ppp0 -s 192.168.1.1/24 -d 0/0 -j MASQUERADE iptables -A forwarding_rule -o ppp0 -j ACCEPT iptables -A forwarding_rule -i ppp0 -j ACCEPT iptables -t nat -A postrouting_rule -o ppp0 -j MASQUERADE root@OpenWrt:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.16.20.1 * 255.255.255.255 UH 0 0 0 ppp0 208.85.40.20 * 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 * 255.255.255.0 U 0 0 0 br0 173.183.192.0 * 255.255.224.0 U 0 0 0 vlan1 default d173-183-192-1. 0.0.0.0 UG 0 0 0 vlan1 default 192.168.1.1 0.0.0.0 UG 0 0 0 br0 Any advice is greatly appreciated, I'm not too great with network but am pretty astute at learning ;-)

  Read the article

• Openswan ipsec transport tunnel not going up

  - by gparent

  On ClusterA and B I have installed the "openswan" package on Debian Squeeze. ClusterA ip is 172.16.0.107, B is 172.16.0.108 When they ping one another, it does not reach the destination. /etc/ipsec.conf: version 2.0 # conforms to second version of ipsec.conf specification config setup protostack=netkey oe=off conn L2TP-PSK-CLUSTER type=transport left=172.16.0.107 right=172.16.0.108 auto=start ike=aes128-sha1-modp2048 authby=secret compress=yes /etc/ipsec.secrets: 172.16.0.107 172.16.0.108 : PSK "L2TPKEY" 172.16.0.108 172.16.0.107 : PSK "L2TPKEY" Here is the result of ipsec verify on both machines: root@cluster2:~# ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.28/K2.6.32-5-amd64 (netkey) Checking for IPsec support in kernel [OK] NETKEY detected, testing for disabled ICMP send_redirects [OK] NETKEY detected, testing for disabled ICMP accept_redirects [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [FAILED] Checking for 'ip' command [OK] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] root@cluster2:~# This is the end of the output of ipsec auto --status: 000 "cluster": 172.16.0.108<172.16.0.108>[+S=C]...172.16.0.107<172.16.0.107>[+S=C]; prospective erouted; eroute owner: #0 000 "cluster": myip=unset; hisip=unset; 000 "cluster": ike_life: 3600s; ipsec_life: 28800s; rekey_margin: 540s; rekey_fuzz: 100%; keyingtries: 0 000 "cluster": policy: PSK+ENCRYPT+COMPRESS+PFS+UP+IKEv2ALLOW+lKOD+rKOD; prio: 32,32; interface: eth0; 000 "cluster": newest ISAKMP SA: #1; newest IPsec SA: #0; 000 "cluster": IKE algorithm newest: AES_CBC_128-SHA1-MODP2048 000 000 #3: "cluster":500 STATE_QUICK_R0 (expecting QI1); EVENT_CRYPTO_FAILED in 298s; lastdpd=-1s(seq in:0 out:0); idle; import:admin initiate 000 #2: "cluster":500 STATE_QUICK_I1 (sent QI1, expecting QR1); EVENT_RETRANSMIT in 13s; lastdpd=-1s(seq in:0 out:0); idle; import:admin initiate 000 #1: "cluster":500 STATE_MAIN_I4 (ISAKMP SA established); EVENT_SA_REPLACE in 2991s; newest ISAKMP; lastdpd=-1s(seq in:0 out:0); idle; import:admin initiate 000 Interestingly enough, if I do ike-scan on the server here's what happens: Doesn't seem to take my ike settings into account root@cluster1:~# ike-scan -M 172.16.0.108 Starting ike-scan 1.9 with 1 hosts (http://www.nta-monitor.com/tools/ike-scan/) 172.16.0.108 Main Mode Handshake returned HDR=(CKY-R=641bffa66ba717b6) SA=(Enc=3DES Hash=SHA1 Auth=PSK Group=2:modp1024 LifeType=Seconds LifeDuration(4)=0x00007080) VID=4f45517b4f7f6e657a7b4351 VID=afcad71368a1f1c96b8696fc77570100 (Dead Peer Detection v1.0) Ending ike-scan 1.9: 1 hosts scanned in 0.008 seconds (118.19 hosts/sec). 1 returned handshake; 0 returned notify root@cluster1:~# I can't tell what's going on here, this is pretty much the simplest config I can have according to the examples.

  Read the article

• Issue in setting up VPN connection (IKEv1) using android (ICS vpn client) with Strongswan 4.5.0 server

  - by Kushagra Bhatnagar

  I am facing issues in setting up VPN connection(IKEv1) using android (ICS vpn client) and Strongswan 4.5.0 server. Below is the set up: Strongswan server is running on ubuntu linux machine which is connected to some wifi hotspot. Using the steps in this guide link, I generated CA, server and client certificate. Once certificates are generated, following (clientCert.p12 and caCert.pem) are sent to mobile via mail and installed on android device. Below are the ip addresses assigned to various interfaces Linux server wlan0 interface ip where server is running: 192.168.43.212, android device eth0 interface ip address: 192.168.43.62; Android device is also attached with the same wifi hotspot. On the Android device, I uses IPsec Xauth RSA option for setting up VPN authentication configuration. I am using the following ipsec.conf configuration: # basic configuration config setup plutodebug=all # crlcheckinterval=600 # strictcrlpolicy=yes # cachecrls=yes nat_traversal=yes # charonstart=yes plutostart=yes # Add connections here. # Sample VPN connections conn ios1 keyexchange=ikev1 authby=xauthrsasig xauth=server left=%defaultroute leftsubnet=0.0.0.0/0 leftfirewall=yes leftcert=serverCert.pem right=192.168.43.62 rightsubnet=10.0.0.0/24 rightsourceip=10.0.0.2 rightcert=clientCert.pem pfs=no auto=add      With the above configurations when I enable VPN on android device, VPN connection is not successful and it gets timed out in Authentication phase. I ran wireshark on both the android device and strongswan server, from the tcpdump below are the observations. Initially Identity Protection (Main mode) exchanges happens between device and server and all are successful. After all successful Identity Protection (Main mode) exchanges server is sending Transaction (Config mode) to device. In reply android device is sending Informational message instead of Transaction (Config mode) message. Further server is keep on sending Transaction (Config mode) message and device is again sending Identity Protection (Main mode) messages. Finally timeout happens and connection fails. I also capture Strongswan server logs and below are the snippets from the server logs which also verifies the same(described above). Apr 27 21:09:40 Linux pluto[12105]: | **parse ISAKMP Message: Apr 27 21:09:40 Linux pluto[12105]: | initiator cookie: Apr 27 21:09:40 Linux pluto[12105]: | 06 fd 61 b8 86 82 df ed Apr 27 21:09:40 Linux pluto[12105]: | responder cookie: Apr 27 21:09:40 Linux pluto[12105]: | 73 7a af 76 74 f0 39 8b Apr 27 21:09:40 Linux pluto[12105]: | next payload type: ISAKMP_NEXT_HASH Apr 27 21:09:40 Linux pluto[12105]: | ISAKMP version: ISAKMP Version 1.0 Apr 27 21:09:40 Linux pluto[12105]: | exchange type: ISAKMP_XCHG_INFO Apr 27 21:09:40 Linux pluto[12105]: | flags: ISAKMP_FLAG_ENCRYPTION Apr 27 21:09:40 Linux pluto[12105]: | message ID: a2 80 ad 82 Apr 27 21:09:40 Linux pluto[12105]: | length: 92 Apr 27 21:09:40 Linux pluto[12105]: | ICOOKIE: 06 fd 61 b8 86 82 df ed Apr 27 21:09:40 Linux pluto[12105]: | RCOOKIE: 73 7a af 76 74 f0 39 8b Apr 27 21:09:40 Linux pluto[12105]: | peer: c0 a8 2b 3e Apr 27 21:09:40 Linux pluto[12105]: | state hash entry 25 Apr 27 21:09:40 Linux pluto[12105]: | state object not found Apr 27 21:09:40 Linux pluto[12105]: packet from 192.168.43.62:500: Informational Exchange is for an unknown (expired?) SA Apr 27 21:09:40 Linux pluto[12105]: | next event EVENT_RETRANSMIT in 10 seconds for #9 Can anyone please provide update on this issue. Why the VPN connection gets timed out and why the ISAKMP exchanges are not proper between Android and strongswan server.

  Read the article

• Why did Ubuntu suddenly get so slow?

  - by user101383

  12.10 has been slowing down mysteriously. Normally, in past versions, I can log in, open Firefox, and it will pop up within seconds. 12.10 is like that upon install too, though once I install my old apps, it gets very slow by Ubuntu standards. After login the hard drive will just make noise for a while before the OS will do anything. Hardware: enter description: Desktop Computer product: XPS 8300 () vendor: Dell Inc. serial: B6G2WR1 width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: boot=normal chassis=desktop uuid=44454C4C-3600-1047-8032-C2C04F575231 core description: Motherboard product: 0Y2MRG vendor: Dell Inc. physical id: 0 version: A00 serial: ..CN7360419G04VQ. slot: To Be Filled By O.E.M. *cpu description: CPU product: Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz serial: To Be Filled By O.E.M. slot: CPU 1 size: 1600MHz capacity: 1600MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=1 threads=2 *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 256KiB capacity: 256KiB capabilities: internal write-through unified *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 1MiB capacity: 1MiB capabilities: internal write-through unified *-cache:2 DISABLED description: L3 cache physical id: 7 slot: L3-Cache size: 8MiB capacity: 8MiB capabilities: internal write-back unified *-memory description: System Memory physical id: 20 slot: System board or motherboard size: 8GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NF-CG vendor: Nanya physical id: 0 serial: 7228183 slot: DIMM3 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NF-CG vendor: Nanya physical id: 1 serial: 1E28183 slot: DIMM1 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NF-CG vendor: Nanya physical id: 2 serial: 9E28183 slot: DIMM4 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:3 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NF-CG vendor: Nanya physical id: 3 serial: 5527183 slot: DIMM2 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-firmware description: BIOS vendor: Dell Inc. physical id: 0 version: A05 date: 09/21/2011 size: 64KiB capacity: 4032KiB capabilities: mca pci upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb zipboot biosbootspecification *-pci description: Host bridge product: 2nd Generation Core Processor Family DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 09 width: 32 bits clock: 33MHz *-pci:0 description: PCI bridge product: Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port vendor: Intel Corporation physical id: 1 bus info: pci@0000:00:01.0 version: 09 width: 32 bits clock: 33MHz capabilities: pci pm msi pciexpress normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:e000(size=4096) memory:fe600000-fe6fffff ioport:d0000000(size=268435456) *-display description: VGA compatible controller product: Juniper [Radeon HD 5700 Series] vendor: Advanced Micro Devices [AMD] nee ATI physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:44 memory:d0000000-dfffffff memory:fe620000-fe63ffff ioport:e000(size=256) memory:fe600000-fe61ffff *-multimedia description: Audio device product: Juniper HDMI Audio [Radeon HD 5700 Series] vendor: Advanced Micro Devices [AMD] nee ATI physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:48 memory:fe640000-fe643fff *-communication description: Communication controller product: 6 Series/C200 Series Chipset Family MEI Controller #1 vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: driver=mei latency=0 resources: irq:45 memory:fe708000-fe70800f *-usb:0 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:16 memory:fe707000-fe7073ff *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:46 memory:fe700000-fe703fff *-pci:1 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:41 memory:fe500000-fe5fffff *-network description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=bcma-pci-bridge latency=0 resources: irq:16 memory:fe500000-fe503fff *-pci:2 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 4 vendor: Intel Corporation physical id: 1c.3 bus info: pci@0000:00:1c.3 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:42 memory:fe400000-fe4fffff *-network description: Ethernet interface product: NetLink BCM57788 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 01 serial: 18:03:73:e1:a7:71 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=192.168.1.3 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:47 memory:fe400000-fe40ffff *-usb:1 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:fe706000-fe7063ff *-isa description: ISA bridge product: H67 Express Chipset Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: SATA controller product: 6 Series/C200 Series Chipset Family SATA AHCI Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 version: 05 width: 32 bits clock: 66MHz capabilities: storage msi pm ahci_1.0 bus_master cap_list configuration: driver=ahci latency=0 resources: irq:43 ioport:f070(size=8) ioport:f060(size=4) ioport:f050(size=8) ioport:f040(size=4) ioport:f020(size=32) memory:fe705000-fe7057ff *-serial UNCLAIMED description: SMBus product: 6 Series/C200 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:fe704000-fe7040ff ioport:f000(size=32) *-scsi:0 physical id: 1 logical name: scsi0 capabilities: emulated *-disk description: ATA Disk product: Hitachi HUA72201 vendor: Hitachi physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: JP4O serial: JPW9J0HD21BTZC size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sectorsize=512 signature=000641dc *-volume:0 description: EXT4 volume vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 logical name: / version: 1.0 serial: 4e3d91b7-fd38-4f44-a9e9-ba3c39b926ec size: 585GiB capacity: 585GiB capabilities: primary journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2012-10-21 16:26:50 filesystem=ext4 lastmountpoint=/ modified=2012-10-29 18:12:08 mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,data=ordered mounted=2012-10-29 18:12:08 state=mounted *-volume:1 description: Extended partition physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 size: 7823MiB capacity: 7823MiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 7823MiB capabilities: nofs *-volume:2 description: Windows NTFS volume physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 version: 3.1 serial: 84a92aae-347b-7940-a2d1-f4745b885ef2 size: 337GiB capacity: 337GiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2012-10-21 18:43:39 filesystem=ntfs modified_by_chkdsk=true mounted_on_nt4=true resize_log_file=true state=dirty upgrade_on_mount=true *-scsi:1 physical id: 2 logical name: scsi1 capabilities: emulated *-cdrom description: DVD-RAM writer product: DVDRWBD DH-12E3S vendor: PLDS physical id: 0.0.0 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: MD11 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-scsi:2 physical id: 3 bus info: usb@2:1.8 logical name: scsi6 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk:0 description: SCSI Disk physical id: 0.0.0 bus info: scsi@6:0.0.0 logical name: /dev/sdb configuration: sectorsize=512 *-disk:1 description: SCSI Disk physical id: 0.0.1 bus info: scsi@6:0.0.1 logical name: /dev/sdc configuration: sectorsize=512 *-disk:2 description: SCSI Disk physical id: 0.0.2 bus info: scsi@6:0.0.2 logical name: /dev/sdd configuration: sectorsize=512 *-disk:3 description: SCSI Disk product: MS/MS-Pro vendor: Generic- physical id: 0.0.3 bus info: scsi@6:0.0.3 logical name: /dev/sde version: 1.03 serial: 3 capabilities: removable configuration: sectorsize=512 *-medium physical id: 0 logical name: /dev/sde

  Read the article

• Unable to enable wireless on a Vostro 2520

  - by Joe

  I have a Vostro 2520 and not sure how to enable wireless on my machine. The details are given below, would appreciate any pointers to resolving this issue. lsmod returns Module Size Used by ath9k 132390 0 ath9k_common 14053 1 ath9k ath9k_hw 411151 2 ath9k,ath9k_common ath 24067 3 ath9k,ath9k_common,ath9k_hw b43 365785 0 mac80211 506816 2 ath9k,b43 cfg80211 205544 4 ath9k,ath,b43,mac80211 bcma 26696 1 b43 ssb 52752 1 b43 ndiswrapper 282628 0 ums_realtek 18248 0 usb_storage 49198 1 ums_realtek uas 18180 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_cirrus 24002 1 joydev 17693 0 parport_pc 32866 0 ppdev 17113 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep psmouse 97362 0 dell_wmi 12681 0 sparse_keymap 13890 1 dell_wmi snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_cirrus,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq wmi 19256 1 dell_wmi snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_cirrus,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device mac_hid 13253 0 i915 473240 3 drm_kms_helper 46978 1 i915 uvcvideo 72627 0 drm 242038 4 i915,drm_kms_helper videodev 98259 1 uvcvideo soundcore 15091 1 snd dell_laptop 18119 0 dcdbas 14490 1 dell_laptop i2c_algo_bit 13423 1 i915 v4l2_compat_ioctl32 17128 1 videodev snd_page_alloc 18529 2 snd_hda_intel,snd_pcm video 19596 1 i915 serio_raw 13211 0 mei 41616 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 sudo lshw -class network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7c00000-f7c07fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 07 serial: 78:45:c4:a3:aa:65 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.1.5 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:e000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: yes Output of lspci > 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev > 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge > Graphics Controller (rev 09) 00:16.0 Communication controller: Intel > Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB > controller: Intel Corporation Panther Point USB Enhanced Host > Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther > Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: > Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) > 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root > Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point > PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel > Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) > 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller > (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 > port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel > Corporation Panther Point SMBus Controller (rev 04) 07:00.0 Network > controller: Broadcom Corporation Device 4365 (rev 01) 09:00.0 Ethernet > controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express > Gigabit Ethernet controller (rev 07) Output of lspci -v 0:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) (prog-if 00 [VGA controller]) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0, IRQ 43 Memory at f7800000 (64-bit, non-prefetchable) [size=4M] Memory at e0000000 (64-bit, prefetchable) [size=256M] I/O ports at f000 [size=64] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0, IRQ 42 Memory at f7d0a000 (64-bit, non-prefetchable) [size=16] Capabilities: <access denied> Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) (prog-if 20 [EHCI]) Subsystem: Dell Device 0558 Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at f7d08000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at f7d00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 Memory behind bridge: f7c00000-f7cfffff Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=09, subordinate=09, sec-latency=0 I/O behind bridge: 0000e000-0000efff Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) (prog-if 20 [EHCI]) Subsystem: Dell Device 0558 Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at f7d07000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) Subsystem: Dell Device 0558 Flags: bus master, medium devsel, latency 0 Capabilities: <access denied> Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) Subsystem: Dell Device 0558 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 40 I/O ports at f0b0 [size=8] I/O ports at f0a0 [size=4] I/O ports at f090 [size=8] I/O ports at f080 [size=4] I/O ports at f060 [size=32] Memory at f7d06000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) Subsystem: Dell Device 0558 Flags: medium devsel, IRQ 11 Memory at f7d05000 (64-bit, non-prefetchable) [size=256] I/O ports at f040 [size=32] Kernel modules: i2c-i801 07:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) Subsystem: Dell Device 0016 Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at f7c00000 (64-bit, non-prefetchable) [size=32K] Capabilities: <access denied> 09:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0, IRQ 41 I/O ports at e000 [size=256] Memory at f0004000 (64-bit, prefetchable) [size=4K] Memory at f0000000 (64-bit, prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: r8169 Kernel modules: r8169

  Read the article

• Facing issues in setting up VPN connection(IKEv1) using iphone (Defult Cisco VPN client) and Strongswan 4.5.0 server

  - by Kushagra Bhatnagar

  I am facing issues in setting up VPN connection(IKEv1) using iPhone (Defult Cisco VPN client) and Strongswan 4.5.0 server. The Strongswan server is running on Ubuntu Linux, which is connected to some wifi hotspot. This is the guide which was used. I generated CA, server and client certificate, with the only difference mentioned below. “While generating server certificate, as per link CN=vpn.strongswan.org instead of this I changed CN name to CN=192.168.43.212.” Once certificates are generated, following (clientCert.p12 and caCert.pem) are sent to mobile via mail and installed on iphone. After installation I notice that certificates are considered as trusted also. Below are the ip addresses assigned to various interfaces Linux server wlan0 interface ip where server is running: 192.168.43.212 Iphone eth0 interface ip address: 192.168.43.72. iphone is also attached with the same wifi hotspot. Below is the snapshot of client configurations. Description Strong swan Server 192.168.43.212 Account ipsecvpn Password ***** Use certificate ON Certificate client The above username and password are in sync with the ipsec.secrets file. I am using the following ipsec.conf configuration: # basic configuration config setup plutodebug=all # crlcheckinterval=600 # strictcrlpolicy=yes # cachecrls=yes nat_traversal=yes # charonstart=yes plutostart=yes # Add connections here. # Sample VPN connections conn ios1 keyexchange=ikev1 authby=xauthrsasig xauth=server left=%defaultroute leftsubnet=0.0.0.0/0 leftfirewall=yes leftcert=serverCert.pem right=192.168.43.72 rightsubnet=10.0.0.0/24 rightsourceip=10.0.0.2 rightcert=clientCert.pem pfs=no auto=add With the above configurations when I enable VPN on iphone, it says Could not able to verify server certificate. I ran Wireshark on a Linux server and observe that initially some ISAKMP message exchanges happens between client and server, which are successful but before authorization, client is sending some informational message and soon after this client is showing error as popup Could not able to verify server certificate. Capture logs on Strongswan server and in server logs below errors are observed: From auth.log Apr 25 20:16:08 Linux pluto[4025]: | ISAKMP version: ISAKMP Version 1.0 Apr 25 20:16:08 Linux pluto[4025]: | exchange type: ISAKMP_XCHG_INFO Apr 25 20:16:08 Linux pluto[4025]: | flags: ISAKMP_FLAG_ENCRYPTION Apr 25 20:16:08 Linux pluto[4025]: | message ID: 9d 1a ea 4d Apr 25 20:16:08 Linux pluto[4025]: | length: 76 Apr 25 20:16:08 Linux pluto[4025]: | ICOOKIE: f6 b7 06 b2 b1 84 5b 93 Apr 25 20:16:08 Linux pluto[4025]: | RCOOKIE: 86 92 a0 c2 a6 2f ac be Apr 25 20:16:08 Linux pluto[4025]: | peer: c0 a8 2b 48 Apr 25 20:16:08 Linux pluto[4025]: | state hash entry 8 Apr 25 20:16:08 Linux pluto[4025]: | state object not found Apr 25 20:16:08 Linux pluto[4025]: **packet from 192.168.43.72:500: Informational Exchange is for an unknown (expired?) SA** Apr 25 20:16:08 Linux pluto[4025]: | next event EVENT_RETRANSMIT in 8 seconds for #8 Apr 25 20:16:16 Linux pluto[4025]: | Apr 25 20:16:16 Linux pluto[4025]: | *time to handle event Apr 25 20:16:16 Linux pluto[4025]: | event after this is EVENT_RETRANSMIT in 2 seconds Apr 25 20:16:16 Linux pluto[4025]: | handling event EVENT_RETRANSMIT for 192.168.43.72 "ios1" #8 Apr 25 20:16:16 Linux pluto[4025]: | sending 76 bytes for EVENT_RETRANSMIT through wlan0 to 192.168.43.72:500: Apr 25 20:16:16 Linux pluto[4025]: | a6 a5 86 41 4b fb ff 99 c9 18 34 61 01 7b f1 d9 Apr 25 20:16:16 Linux pluto[4025]: | 08 10 06 01 e9 1c ea 60 00 00 00 4c ba 7d c8 08 Apr 25 20:16:16 Linux pluto[4025]: | 13 47 95 18 19 31 45 30 2e 22 f9 4d 85 2c 27 bc Apr 25 20:16:16 Linux pluto[4025]: | 9e 9b e1 ae 1e 35 51 6f ab 80 f5 73 3c 15 8d 20 Apr 25 20:16:16 Linux pluto[4025]: | 4b 46 47 86 50 24 3f 13 15 7d d5 17 Apr 25 20:16:16 Linux pluto[4025]: | inserting event EVENT_RETRANSMIT, timeout in 40 seconds for #8 Apr 25 20:16:16 Linux pluto[4025]: | next event EVENT_RETRANSMIT in 2 seconds for #10 Apr 25 20:16:16 Linux pluto[4025]: | rejected packet: Apr 25 20:16:16 Linux pluto[4025]: | Apr 25 20:16:16 Linux pluto[4025]: | control: Apr 25 20:16:16 Linux pluto[4025]: | 30 00 00 00 00 00 00 00 00 00 00 00 0b 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: | 6f 00 00 00 02 03 03 00 00 00 00 00 00 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: | 02 00 00 00 c0 a8 2b 48 00 00 00 00 00 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: | name: Apr 25 20:16:16 Linux pluto[4025]: | 02 00 01 f4 c0 a8 2b 48 00 00 00 00 00 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: **ERROR: asynchronous network error report on wlan0 for message to 192.168.43.72 port 500, complainant 192.168.43.72: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)]** Anybody please provide some update about this error and how to solve this issue.

  Read the article

• Disk Drive not working

  - by user287681

  The CD/DVD drive on my sisters' (I'm helping her shift from Win. XP (now officially deprecated by Microsoft) to Ubuntu) system. Now, it may end up being a failed attempt, all together (Almost the whole last year (when she's been on XP) the disk drive hasn't (not even powering on) been working.), I just want to make sure I've explored every remote possibility. Because I figure, "Huh, now that I've got Ubuntu running, instead of XP, that (just) might make a difference.". I have tried using the sudo lshw command in the terminal, to (seemingly) no avil, but, who knows, you might be able to make something out of it. Here's the output: kyra@kyra-Satellite-P105:~$ sudo lshw [sudo] password for kyra: kyra-satellite-p105 description: Notebook product: Satellite P105 () vendor: TOSHIBA version: PSPA0U-0TN01M serial: 96084354W width: 64 bits capabilities: smbios-2.4 dmi-2.4 vsyscall32 configuration: administrator_password=disabled boot=oem-specific chassis=notebook frontpanel_password=unknown keyboard_password=unknown power-on_password=disabled uuid=00900559-F88E-D811-82E0-00163680E992 *-core description: Motherboard product: Satellite P105 vendor: TOSHIBA physical id: 0 version: Not Applicable serial: 1234567890 *-firmware description: BIOS vendor: TOSHIBA physical id: 0 version: V4.70 date: 01/19/20092 size: 92KiB capabilities: isa pci pcmcia pnp upgrade shadowing escd cdboot acpi usb biosbootspecification *-cpu description: CPU product: Intel(R) Core(TM)2 CPU T5500 @ 1.66GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: Intel(R) Core(TM)2 CPU T5 slot: U2E1 size: 1667MHz capacity: 1667MHz width: 64 bits clock: 166MHz capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx x86-64 constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl est tm2 ssse3 cx16 xtpr pdcm lahf_lm dtherm cpufreq *-cache:0 description: L1 cache physical id: 5 slot: L1 Cache size: 16KiB capacity: 16KiB capabilities: asynchronous internal write-back *-cache:1 description: L2 cache physical id: 6 slot: L2 Cache size: 2MiB capabilities: burst external write-back *-memory description: System Memory physical id: c slot: System board or motherboard size: 2GiB capacity: 3GiB *-bank:0 description: SODIMM DDR2 Synchronous physical id: 0 slot: M1 size: 1GiB width: 64 bits *-bank:1 description: SODIMM DDR2 Synchronous physical id: 1 slot: M2 size: 1GiB width: 64 bits *-pci description: Host bridge product: Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 03 width: 32 bits clock: 33MHz configuration: driver=agpgart-intel resources: irq:0 *-display:0 description: VGA compatible controller product: Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 03 width: 32 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:16 memory:d0200000-d027ffff ioport:1800(size=8) memory:c0000000-cfffffff memory:d0300000-d033ffff *-display:1 UNCLAIMED description: Display controller product: Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 03 width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: latency=0 resources: memory:d0280000-d02fffff *-multimedia description: Audio device product: NM10/ICH7 Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 02 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:44 memory:d0340000-d0343fff *-pci:0 description: PCI bridge product: NM10/ICH7 Family PCI Express Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: 02 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:3000(size=4096) memory:84000000-841fffff ioport:84200000(size=2097152) *-pci:1 description: PCI bridge product: NM10/ICH7 Family PCI Express Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: 02 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:41 ioport:4000(size=4096) memory:84400000-846fffff ioport:84700000(size=2097152) *-network description: Wireless interface product: PRO/Wireless 3945ABG [Golan] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 02 serial: 00:13:02:d6:d2:35 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwl3945 driverversion=3.13.0-29-generic firmware=15.32.2.9 ip=10.110.20.157 latency=0 link=yes multicast=yes wireless=IEEE 802.11abg resources: irq:43 memory:84400000-84400fff *-pci:2 description: PCI bridge product: NM10/ICH7 Family PCI Express Port 3 vendor: Intel Corporation physical id: 1c.2 bus info: pci@0000:00:1c.2 version: 02 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:42 ioport:5000(size=4096) memory:84900000-84afffff ioport:84b00000(size=2097152) *-usb:0 description: USB controller product: NM10/ICH7 Family USB UHCI Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:23 ioport:1820(size=32) *-usb:1 description: USB controller product: NM10/ICH7 Family USB UHCI Controller #2 vendor: Intel Corporation physical id: 1d.1 bus info: pci@0000:00:1d.1 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:19 ioport:1840(size=32) *-usb:2 description: USB controller product: NM10/ICH7 Family USB UHCI Controller #3 vendor: Intel Corporation physical id: 1d.2 bus info: pci@0000:00:1d.2 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:18 ioport:1860(size=32) *-usb:3 description: USB controller product: NM10/ICH7 Family USB UHCI Controller #4 vendor: Intel Corporation physical id: 1d.3 bus info: pci@0000:00:1d.3 version: 02 width: 32 bits clock: 33MHz capabilities: uhci bus_master configuration: driver=uhci_hcd latency=0 resources: irq:16 ioport:1880(size=32) *-usb:4 description: USB controller product: NM10/ICH7 Family USB2 EHCI Controller vendor: Intel Corporation physical id: 1d.7 bus info: pci@0000:00:1d.7 version: 02 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci-pci latency=0 resources: irq:23 memory:d0544000-d05443ff *-pci:3 description: PCI bridge product: 82801 Mobile PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: e2 width: 32 bits clock: 33MHz capabilities: pci subtractive_decode bus_master cap_list resources: ioport:2000(size=4096) memory:d0000000-d00fffff ioport:80000000(size=67108864) *-pcmcia description: CardBus bridge product: PCIxx12 Cardbus Controller vendor: Texas Instruments physical id: 4 bus info: pci@0000:0a:04.0 version: 00 width: 32 bits clock: 33MHz capabilities: pcmcia bus_master cap_list configuration: driver=yenta_cardbus latency=176 maxlatency=5 mingnt=192 resources: irq:17 memory:d0004000-d0004fff ioport:2400(size=256) ioport:2800(size=256) memory:80000000-83ffffff memory:88000000-8bffffff *-firewire description: FireWire (IEEE 1394) product: PCIxx12 OHCI Compliant IEEE 1394 Host Controller vendor: Texas Instruments physical id: 4.1 bus info: pci@0000:0a:04.1 version: 00 width: 32 bits clock: 33MHz capabilities: pm ohci bus_master cap_list configuration: driver=firewire_ohci latency=64 maxlatency=4 mingnt=3 resources: irq:17 memory:d0007000-d00077ff memory:d0000000-d0003fff *-storage description: Mass storage controller product: 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) vendor: Texas Instruments physical id: 4.2 bus info: pci@0000:0a:04.2 version: 00 width: 32 bits clock: 33MHz capabilities: storage pm bus_master cap_list configuration: driver=tifm_7xx1 latency=64 maxlatency=4 mingnt=7 resources: irq:17 memory:d0005000-d0005fff *-generic description: SD Host controller product: PCIxx12 SDA Standard Compliant SD Host Controller vendor: Texas Instruments physical id: 4.3 bus info: pci@0000:0a:04.3 version: 00 width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: driver=sdhci-pci latency=64 maxlatency=4 mingnt=7 resources: irq:17 memory:d0007800-d00078ff *-network description: Ethernet interface product: PRO/100 VE Network Connection vendor: Intel Corporation physical id: 8 bus info: pci@0000:0a:08.0 logical name: eth0 version: 02 serial: 00:16:36:80:e9:92 size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.24-k2-NAPI duplex=half latency=64 link=no maxlatency=56 mingnt=8 multicast=yes port=MII speed=10Mbit/s resources: irq:20 memory:d0006000-d0006fff ioport:2000(size=64) *-isa description: ISA bridge product: 82801GBM (ICH7-M) LPC Interface Bridge vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 02 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: driver=lpc_ich latency=0 resources: irq:0 *-ide description: IDE interface product: 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode] vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 version: 02 width: 32 bits clock: 66MHz capabilities: ide pm bus_master cap_list configuration: driver=ata_piix latency=0 resources: irq:19 ioport:1f0(size=8) ioport:3f6 ioport:170(size=8) ioport:376 ioport:18b0(size=16) *-serial UNCLAIMED description: SMBus product: NM10/ICH7 Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 02 width: 32 bits clock: 33MHz configuration: latency=0 resources: ioport:18c0(size=32) *-scsi physical id: 1 logical name: scsi0 capabilities: emulated *-disk description: ATA Disk product: ST9250421AS vendor: Seagate physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: SD13 serial: 5TH0B2HB size: 232GiB (250GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sectorsize=512 signature=000d7fd5 *-volume:0 description: EXT4 volume vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 logical name: / version: 1.0 serial: 13bb4bdd-8cc9-40e2-a490-dbe436c2a02d size: 230GiB capacity: 230GiB capabilities: primary bootable journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2014-06-01 17:37:01 filesystem=ext4 lastmountpoint=/ modified=2014-06-01 21:15:21 mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,data=ordered mounted=2014-06-01 21:15:21 state=mounted *-volume:1 description: Extended partition physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 size: 2037MiB capacity: 2037MiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 2037MiB capabilities: nofs *-remoteaccess UNCLAIMED vendor: Intel physical id: 1 capabilities: inbound kyra@kyra-Satellite-P105:~$

  Read the article

• Cannot connect to MySQL Server on RHEL 5.7

  - by Jeffrey Wong

  I have a standard MySQL Server running on Red hat 5.7. I have edited /etc/my.cnf to specify the bind address as my server's public IP address. [mysqld] datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql # Default to using old password format for compatibility with mysql 3.x # clients (those using the mysqlclient10 compatibility package). old_passwords=1 # Disabling symbolic-links is recommended to prevent assorted security risks ; # to do so, uncomment this line: # symbolic-links=0 [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid bind-address=171.67.88.25 port=3306 And I have also restarted my firewall sudo /sbin/iptables -A INPUT -i eth0 -p tcp --destination-port 3306 -j ACCEPT /sbin/service iptables save The network administrator has already opened port 3306 for this box. When connecting from a remote computer (running Ubuntu 10.10, server is running RHEL 5.7), I issue mysql -u jeffrey -p --host=171.67.88.25 --port=3306 --socket=/var/lib/mysql/mysql.sock but receive a ERROR 2003 (HY000): Can't connect to MySQL server on '171.67.88.25' (113). I've noticed that the socket file /var/lib/mysql/mysql.sock is blank. Should this be the case? UPDATE The result of netstat -an | grep 3306 tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN Result of sudo netstat -tulpen Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State User Inode PID/Program name tcp 0 0 127.0.0.1:2208 0.0.0.0:* LISTEN 0 7602 3168/hpiod tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 27 7827 3298/mysqld tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 0 5110 2802/portmap tcp 0 0 0.0.0.0:8787 0.0.0.0:* LISTEN 0 8431 3326/rserver tcp 0 0 0.0.0.0:915 0.0.0.0:* LISTEN 0 5312 2853/rpc.statd tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 0 7655 3188/sshd tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 0 7688 3199/cupsd tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 0 8025 3362/sendmail: acce tcp 0 0 127.0.0.1:2207 0.0.0.0:* LISTEN 0 7620 3173/python udp 0 0 0.0.0.0:909 0.0.0.0:* 0 5300 2853/rpc.statd udp 0 0 0.0.0.0:912 0.0.0.0:* 0 5309 2853/rpc.statd udp 0 0 0.0.0.0:68 0.0.0.0:* 0 4800 2598/dhclient udp 0 0 0.0.0.0:36177 0.0.0.0:* 70 8314 3476/avahi-daemon: udp 0 0 0.0.0.0:5353 0.0.0.0:* 70 8313 3476/avahi-daemon: udp 0 0 0.0.0.0:111 0.0.0.0:* 0 5109 2802/portmap udp 0 0 0.0.0.0:631 0.0.0.0:* 0 7691 3199/cupsd Result of sudo /sbin/iptables -L -v -n Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 6373 2110K RH-Firewall-1-INPUT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 RH-Firewall-1-INPUT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT 1241 packets, 932K bytes) pkts bytes target prot opt in out source destination Chain RH-Firewall-1-INPUT (2 references) pkts bytes target prot opt in out source destination 572 861K ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 1 28 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 icmp type 255 0 0 ACCEPT esp -- * * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT ah -- * * 0.0.0.0/0 0.0.0.0/0 46 6457 ACCEPT udp -- * * 0.0.0.0/0 224.0.0.251 udp dpt:5353 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:631 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:631 782 157K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 2 120 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:443 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:23 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 4970 1086K REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Result of nmap -P0 -p3306 171.67.88.25 Host is up (0.027s latency). PORT STATE SERVICE 3306/tcp filtered mysql Nmap done: 1 IP address (1 host up) scanned in 0.09 seconds Solution When everything else fails, go GUI! system-config-securitylevel and add port 3306. All done!

  Read the article

• Samba with remote LDAP authentication doesn`t see users properly

  - by LucasBr

  I'm trying to setup a samba server authenticated by a remote LDAP server, and I'm having some problems that I can't figure how to solve. I was able to make an getent passwd at samba server and I could see all users at ldapserver, but when I tried to access \\SAMBASERVER at my windows box I had this at the /var/log/samba/log.mywindowsbox: <...snip...> [2012/10/19 13:05:22.449684, 2] smbd/sesssetup.c:1413(setup_new_vc_session) setup_new_vc_session: New VC == 0, if NT4.x compatible we would close all old resources. [2012/10/19 13:05:22.449692, 3] smbd/sesssetup.c:1212(reply_sesssetup_and_X_spnego) Doing spnego session setup [2012/10/19 13:05:22.449701, 3] smbd/sesssetup.c:1254(reply_sesssetup_and_X_spnego) NativeOS=[] NativeLanMan=[] PrimaryDomain=[] [2012/10/19 13:05:22.449717, 3] libsmb/ntlmssp.c:747(ntlmssp_server_auth) Got user=[lucas] domain=[BUSINESS] workstation=[MYWINDOWSBOX] len1=24 len2=24 [2012/10/19 13:05:22.449747, 3] auth/auth.c:216(check_ntlm_password) check_ntlm_password: Checking password for unmapped user [BUSINESS]\[lucas]@[MYWINDOWSBOX] with the new password interface [2012/10/19 13:05:22.449759, 3] auth/auth.c:219(check_ntlm_password) check_ntlm_password: mapped user is: [SAMBASERVER]\[lucas]@[MYWINDOWSBOX] [2012/10/19 13:05:22.449773, 3] smbd/sec_ctx.c:210(push_sec_ctx) push_sec_ctx(0, 0) : sec_ctx_stack_ndx = 1 [2012/10/19 13:05:22.449783, 3] smbd/uid.c:429(push_conn_ctx) push_conn_ctx(0) : conn_ctx_stack_ndx = 0 [2012/10/19 13:05:22.449791, 3] smbd/sec_ctx.c:310(set_sec_ctx) setting sec ctx (0, 0) - sec_ctx_stack_ndx = 1 [2012/10/19 13:05:22.449922, 2] lib/smbldap.c:950(smbldap_open_connection) smbldap_open_connection: connection opened [2012/10/19 13:05:23.001517, 3] lib/smbldap.c:1166(smbldap_connect_system) ldap_connect_system: successful connection to the LDAP server [2012/10/19 13:05:23.007713, 3] smbd/sec_ctx.c:418(pop_sec_ctx) pop_sec_ctx (0, 0) - sec_ctx_stack_ndx = 0 [2012/10/19 13:05:23.007733, 3] auth/auth_sam.c:399(check_sam_security) check_sam_security: Couldn't find user 'lucas' in passdb. [2012/10/19 13:05:23.007743, 2] auth/auth.c:314(check_ntlm_password) check_ntlm_password: Authentication for user [lucas] -> [lucas] FAILED with error NT_STATUS_NO_SUCH_USER [2012/10/19 13:05:23.007760, 3] smbd/error.c:80(error_packet_set) error packet at smbd/sesssetup.c(111) cmd=115 (SMBsesssetupX) NT_STATUS_LOGON_FAILURE [2012/10/19 13:05:23.010469, 3] smbd/process.c:1489(process_smb) Transaction 3 of length 142 (0 toread) <...snip...> /etc/samba/smb.conf file follows: [global] dos charset = 850 unix charset = LOCALE workgroup = BUSINESS netbios name = SAMBASERVER bind interfaces only = true interfaces = lo eth0 eth1 smb ports = 139 hosts deny = All hosts allow = 192.168.78. 192.168.255. 127.0.0.1 10.149.122. 192.168.0. name resolve order = wins bcast hosts log level = 3 syslog = 0 log file = /var/log/samba/log.%m max log size = 100000 domain logons = No wins support = Yes wins proxy = No client ntlmv2 auth = Yes lanman auth = Yes ntlm auth = Yes dns proxy = Yes time server = Yes security = user encrypt passwords = Yes obey pam restrictions = Yes ldap password sync = Yes unix password sync = Yes passdb backend = ldapsam:"ldap://192.168.78.206" ldap ssl = off ldap admin dn = uid=root,ou=Users,dc=business,dc=intranet ldap suffix = ldap group suffix = ou=Groups ldap user suffix = ou=Users ldap machine suffix = ou=Computers ldap idmap suffix = ou=Idmap ldap delete dn = Yes add user script = /usr/sbin/smbldap-useradd -m "%u" delete user script = /usr/sbin/smbldap-userdel "%u" add group script = /usr/sbin/smbldap-groupadd -p "%g" delete group script = /usr/sbin/smbldap-groupdel "%g" add user to group script = /usr/sbin/smbldap-groupmod -m "%u" "%g" delete user from group script = /usr/sbin/smbldap-groupmod -x "%u" "%g" set primary group script = /usr/sbin/smbldap-usermod -g "%g" "%u" add machine script = /usr/sbin/smbldap-useradd -W -t5 "%u" idmap backend = ldap:"ldap://192.168.78.206" idmap uid = 16777216-33554431 idmap gid = 16777216-33554431 load printers = No printcap name = /dev/null map acl inherit = Yes map untrusted to domain = Yes enable privileges = Yes veto files = /lost+found/ /publicftp/ So, \\SAMBASERVER says he couldn't find my user, but I can see it by getent passwd . What I can do in order to SAMBASERVER see and authenticate my user? Thanks in advance!

  Read the article

• Cannot get official CentOS 5.4 BIND package to start

  - by Brian Cline

  Yesterday I installed CentOS 5.4 on one of my servers, and it appears that the official BIND/named package has trouble starting for reasons I cannot deduce. Here is what happens: [root@hal init.d]# service named start Starting named: Error in named configuration: /etc/named.conf:57: open: named.root.hints: permission denied [FAILED] The line in question, with the directory option for context: // further up in the file: directory "/var/named"; // line 57: include "named.root.hints"; Like you, my first reaction was to check permissions on /var/named/named.root.hints, /var/named, and /var to make sure the named user would be able to read it. Here are the permissions at each level: drwxr-xr-x 19 root root 4096 Nov 3 02:05 var drwxr-x--- 5 root named 4096 Nov 3 02:36 named -rw-r--r-- 1 named named 524 Mar 29 2006 named.root.hints Everything appears to be fine permission-wise. The same error occurs if the /var/named directory is writable by the named user. I've even temporarily allowed the named user to log in via bash, su'ed from root to named, and checked that I was, in fact, able to cat /var/named/named.root.hints successfully. (Yes, don't worry: I changed the shell back to nologin). My last endeavor showed that BIND is able to run under the named user account and start up just fine, if done so manually: [root@hal ~]# named -u named -g 03-Nov-2009 16:31:02.021 starting BIND 9.3.6-P1-RedHat-9.3.6-4.P1.el5 -u named -g 03-Nov-2009 16:31:02.021 adjusted limit on open files from 1024 to 1048576 03-Nov-2009 16:31:02.021 found 2 CPUs, using 2 worker threads 03-Nov-2009 16:31:02.021 using up to 4096 sockets 03-Nov-2009 16:31:02.028 loading configuration from '/etc/named.conf' 03-Nov-2009 16:31:02.030 using default UDP/IPv4 port range: [1024, 65535] 03-Nov-2009 16:31:02.031 using default UDP/IPv6 port range: [1024, 65535] 03-Nov-2009 16:31:02.034 listening on IPv4 interface lo, 127.0.0.1#53 03-Nov-2009 16:31:02.034 listening on IPv4 interface eth0, 10.0.0.5#53 03-Nov-2009 16:31:02.034 listening on IPv4 interface eth1, ww.xx.yy.zz#53 03-Nov-2009 16:31:02.040 command channel listening on 127.0.0.1#953 03-Nov-2009 16:31:02.040 command channel listening on ::1#953 03-Nov-2009 16:31:02.040 ignoring config file logging statement due to -g option 03-Nov-2009 16:31:02.041 zone 0.in-addr.arpa/IN/localhost_resolver: loaded serial 42 03-Nov-2009 16:31:02.042 zone 0.0.127.in-addr.arpa/IN/localhost_resolver: loaded serial 1997022700 03-Nov-2009 16:31:02.042 zone 255.in-addr.arpa/IN/localhost_resolver: loaded serial 42 03-Nov-2009 16:31:02.042 zone 0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa/IN/localhost_resolver: loaded serial 1997022700 03-Nov-2009 16:31:02.043 zone localdomain/IN/localhost_resolver: loaded serial 42 03-Nov-2009 16:31:02.043 zone localhost/IN/localhost_resolver: loaded serial 42 03-Nov-2009 16:31:02.043 zone x.y.z.in-addr.arpa/IN/internal: loaded serial 1 03-Nov-2009 16:31:02.044 zone x.y.z/IN/internal: loaded serial 2 03-Nov-2009 16:31:02.045 running What type and size of firearm should I use to resolve this? I'd prefer something with automatic ammunition, and, at worst, it should be able to fit on my shoulder. Of course I am open to suggestions.

  Read the article

• Raid 1 array won't assemble after power outage. How do I fix this ext4 mirror?

  - by Forkrul Assail

  Two ext4 drives on Raid 1 with mdadm won't reassemble after the power went out for an extended period (UPS drained). After turning the machine back on, mdadm said that the array was degraded, after which it took about 2 days for a full resync, which completed without problems. On trying to remount the array I get: mount: you must specify the filesystem type cat /etc/fstab lines relevant to setup: /dev/md127 /media/mediapool ext4 defaults 0 0 dmesg | tail (on trying to mount) says: [ 1050.818782] EXT3-fs (md127): error: can't find ext3 filesystem on dev md127. [ 1050.849214] EXT4-fs (md127): VFS: Can't find ext4 filesystem [ 1050.944781] FAT-fs (md127): invalid media value (0x00) [ 1050.944782] FAT-fs (md127): Can't find a valid FAT filesystem [ 1058.272787] EXT2-fs (md127): error: can't find an ext2 filesystem on dev md127. cat /proc/mdstat says: Personalities : [raid1] [linear] [multipath] [raid0] [raid6] [raid5] [raid4] [raid10] md127 : active (auto-read-only) raid1 sdj[2] sdi[0] 2930135360 blocks super 1.2 [2/2] [UU] unused devices: <none> fsck /dev/md127 says: fsck from util-linux 2.20.1 e2fsck 1.42 (29-Nov-2011) fsck.ext2: Superblock invalid, trying backup blocks... fsck.ext2: Bad magic number in super-block while trying to open /dev/md127 The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> mdadm -E /dev/sdi gives me: /dev/sdi: Magic : a92b4efc Version : 1.2 Feature Map : 0x0 Array UUID : 37ac1824:eb8a21f6:bd5afd6d:96da6394 Name : sojourn:33 Creation Time : Sat Nov 10 10:43:52 2012 Raid Level : raid1 Raid Devices : 2 Avail Dev Size : 5860271016 (2794.40 GiB 3000.46 GB) Array Size : 2930135360 (2794.39 GiB 3000.46 GB) Used Dev Size : 5860270720 (2794.39 GiB 3000.46 GB) Data Offset : 262144 sectors Super Offset : 8 sectors State : clean Device UUID : 3e6e9a4f:6c07ab3d:22d47fce:13cecfd0 Update Time : Tue Nov 13 20:34:18 2012 Checksum : f7d10db9 - correct Events : 27 Device Role : Active device 0 Array State : AA ('A' == active, '.' == missing) boot@boot ~ $ sudo mdadm -E /dev/sdj /dev/sdj: Magic : a92b4efc Version : 1.2 Feature Map : 0x0 Array UUID : 37ac1824:eb8a21f6:bd5afd6d:96da6394 Name : sojourn:33 Creation Time : Sat Nov 10 10:43:52 2012 Raid Level : raid1 Raid Devices : 2 Avail Dev Size : 5860271016 (2794.40 GiB 3000.46 GB) Array Size : 2930135360 (2794.39 GiB 3000.46 GB) Used Dev Size : 5860270720 (2794.39 GiB 3000.46 GB) Data Offset : 262144 sectors Super Offset : 8 sectors State : clean Device UUID : 7fb84af4:e9295f7b:ede61f27:bec0cb57 Update Time : Tue Nov 13 20:34:18 2012 Checksum : b9d17fef - correct Events : 27 Device Role : Active device 1 Array State : AA ('A' == active, '.' == missing) machine@user ~ dmesg | tail [ 61.785866] init: alsa-restore main process (2736) terminated with status 99 [ 68.433548] eth0: no IPv6 routers present [ 534.142511] EXT4-fs (sdi): ext4_check_descriptors: Block bitmap for group 0 not in group (block 2838187772)! [ 534.142518] EXT4-fs (sdi): group descriptors corrupted! [ 546.418780] EXT2-fs (sdi): error: couldn't mount because of unsupported optional features (240) [ 549.654127] EXT3-fs (sdi): error: couldn't mount because of unsupported optional features (240) Since this is Raid 1 it was suggested that I try and mount or fsck the drives separately. After a long fsck on one drive, it ended with this as tail: Illegal double indirect block (2298566437) in inode 39717736. CLEARED. Illegal block #4231180 (2611866932) in inode 39717736. CLEARED. Error storing directory block information (inode=39717736, block=0, num=1092368): Memory allocation failed Recreate journal? yes Creating journal (32768 blocks): Done. *** journal has been re-created - filesystem is now ext3 again *** The drive however still doesn't want to mount: dmesg | tail [ 170.674659] md: export_rdev(sdc) [ 170.675152] md: export_rdev(sdc) [ 195.275288] md: export_rdev(sdc) [ 195.275876] md: export_rdev(sdc) [ 1338.540092] CE: hpet increased min_delta_ns to 30169 nsec [26125.734105] EXT4-fs (sdc): ext4_check_descriptors: Checksum for group 0 failed (43502!=37987) [26125.734115] EXT4-fs (sdc): group descriptors corrupted! [26182.325371] EXT3-fs (sdc): error: couldn't mount because of unsupported optional features (240) [27083.316519] EXT4-fs (sdc): ext4_check_descriptors: Checksum for group 0 failed (43502!=37987) [27083.316530] EXT4-fs (sdc): group descriptors corrupted! Please help me fix this. I never in my wildest nightmares thought a complete mirror would die this badly. Am I missing something? Suggestions on fixing this? Could someone explain why it would resync after the powerout, only to seemingly nuke the drive? Thanks for reading. Any help much appreciated. I've tried everything I can think of, including booting and filesystem checking with SystemRescue and Ubuntu liveboot discs.

  Read the article

< Previous Page | 52 53 54 55 56 57 58 59  | Next Page >