Search Results

Search found 1454 results on 59 pages for 'eth0'.

Page 53/59 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59  | Next Page >

• NAT via iptables and virtual interface

  - by Alex

  I'm trying to implement the following scenario: One VM-host, multiple guest VMs, each one gets its own IP-address (and domain). Our server has only one physical interface, so the intended use is to add virtual interfaces on eth0. To complicate our situation the provider uses port-security on their switches, so I can't run the guest interfaces in bridged mode, because then the switch detects a "spoofed" MAC-address and kills the interface (permanently, forcing me to call the support, which I'm sure will get them a little bit angry the third time ;) ). My first guess was to use iptables and NAT to forward all packages from one virtual interface to another one, but iptables doesn't seem to like virtual interfaces (at least I can't get it to work properly). So my second guess is to use the source IP of the packages to the public interface. Let's assume libvirt creates a virbr0-network with 192.168.100.0/24 and the guest uses 192.168.100.2 as IP-address. This is what I tried to use: iptables -t nat -I PREROUTING --src public_ip_on_eth0:0 -p tcp --dport 80 -j DNAT --to-destination 192.168.100.2:80 That doesn't give me the intended results either (accessing the server times out). Is there a way to do what I'm trying to do, or even to route all traffic to a certain IP on a virtual interface to the VM's device?

  Read the article

• Macvlan based interface pings from host but not from namespace

  - by jtlebi

  My setup: Private network vboxnet1 10.0.7.0/24 1 Host, ubuntu desktop 1 VM, ubuntu server (VirtualBox) Adressing layout: HOST: 10.0.7.1 VM: 10.0.7.101 VM MAC NAMESPACE: 10.0.7.102 On the VM, I ran the following commands: ip netns add mac # create a new nmespace ip link add link eth0 mac0 type macvlan # create a new macvlan interface ip link set mac0 netns mac On the mac namespace, inside the VM: ip link set lo up ip link set mac up ip addr add 10.0.7.102/24 dev mac0 So that we basically end up with: (Like Inception ?) +------------------------+ | Host: 10.0.7.1 | | | | +--------------------+ | | | VM: 10.0.7.101 | | | | | | | | +----------------+ | | | | | NS: 10.0.7.102 | | | | | | | | | | | +----------------+ | | | +--------------------+ | +------------------------+ What works: Ping between Host and VM Ping between NS and NS dhclient from NS What does not work: ping between NS and VM ping between NS and Host Where I started to go nuts: tcpdump on host (the real machine) actually shows ARP request AND replies tcpdump on NS shows ARP requests sent to the host tcpdump on VM makes the whole mess work (!) -- ping starts to get answers when tcpdump is started on the VM ?!? So, I bet you were eager for it, my question is: how to I make it work ? I suspect something's wrong with ARP on the macvlan inside the NS but can't figure out what exactly... Btw, I did the same expérimentations with the mac0 interface directly on the VM (no namespace) and it worked flawlessly.

  Read the article

• Backtrack, Wi-Fi not working

  - by hradecek

  I've installed Backtrack 5R3 KDE, and I realized that my wireless is not working, but wired is working fine. Here's the lshw output: *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 05 serial: 04:7d:7b:b7:46:f8 size: 100MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:42 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff lspci output: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB Controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

  Read the article

• Prevent Linux from processing incoming ICMP Host unreachable packets

  - by bbc

  I have a test setup with one host on a network (10.1.0.0/16) talking via TCP to another one on another network (10.2.0.0/16) and a gateway in the middle. Sometimes, the TCP connection is lost and while scanning the trace (pcap), I looks like it's because of just one ICMP Host unreachable message sent by the gateway to 10.1.0.1 at some point. 10.1.0.1 then sends a TCP RST to 10.2.0.1. In my opinion, the gateway (pfSense) is broken or not configured correctly but anyway, for testing purposes, I'd like to block this kind of ICMP on the host (10.1.0.1) before it has an influence on my TCP connection (or does it? I'm not even sure). I've tried iptables: iptables -I INPUT -i eth0 -p icmp --icmp-type host-unreachable -j DROP but while it does a good job at preventing userpace applications like ping from receiving these ICMP messages, my TCP connection still comes to an end when the alleged "killer ICMP packet" is sent by the gateway. Am I right about how it is processed? If yes, then what can I do to achieve my goal?

  Read the article

• Why is this iptables rule that does port forwarding not working?

  - by videoguy

  I have a server bound to localhost:7060. It is using ipv6 socket instead of ipv4. Below is netstat outout. # netstat -an Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 10.200.32.98:1720 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4122 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4123 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:4123 127.0.0.1:43051 ESTABLISHED tcp 0 0 10.200.32.98:5555 10.200.32.44:53162 ESTABLISHED tcp6 0 0 :::5060 :::* LISTEN tcp6 0 0 ::ffff:127.0.0.1:7060 :::* LISTEN tcp6 0 0 :::23 :::* LISTEN tcp6 0 0 ::ffff:10.200.32.98:23 ::ffff:10.200.32.142:43505 ESTABLISHED tcp6 0 0 ::ffff:127.0.0.1:43051 ::ffff:127.0.0.1:4123 ESTABLISHED tcp6 0 0 ::ffff:10.200.32.98:23 ::ffff:10.200.32.44:53195 ESTABLISHED udp6 0 0 :::5060 :::* CLOSE # I want to setup a port forwarding rule that accepts connections on port 24 (on all interfaces loopback as well as eth0) and forward the data to localhost:7060. This is how I am setting up the iptables rule: iptables -t nat -A PREROUTING -p tcp --dport 24 -j DNAT --to 127.0.0.1:7060** It is not working. When I telnet from different box, I see the following $telnet 10.200.32.98 24 Trying 10.200.32.98... If I change the server to bind to *:7060 and set the following rule, it seems to work fine. iptables -t nat -A PREROUTING -p tcp --dport 24 -j REDIRECT --to-port 7060 But that will make my server available on WAN interface which I don't like. I feel it had something to do with ipv6 socket (tcp6 line in netstat output). This whole thing is done on an Android device with custom built Android platform image. How do I get this working?

  Read the article

• Server not resolving after restart

  - by DomainSoil

  I restarted our server today, and now cannot for the life of me get anything to resolve... I suspect it has something to do with our routes. I've tried numerous Google results to no avail. Here is as far as I've gotten: [root@www ~]# route -n Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.101 0.0.0.0 255.255.255.255 UH 0 0 0 eth1 0.0.0.0 192.168.1.101 0.0.0.0 UG 0 0 0 eth1 Things you need to know: Our server (CentOS 6.3) runs two virtual machines, one live, and one development. They mirror each other as much as possible, but I can't find where I've went wrong with the live server. The dev server works fine. [root@www ~]# ifconfig eth1 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx inet6 addr: xxxx:xxx:xxxx:xxxx:xxxx/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118206 errors:0 dropped:0 overruns:0 frame:0 TX packets:165 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7825749 (7.4 Mib) TX bytes:7146 (69.2 KiB) Interrupt:28 [root@www ~]# /etc/init.d/network status Configured devices: lo Auto eth0 Currently active devices: lo eth1 If there is any other information you need, please don't hesitate to ask!

  Read the article

• upstart scripts: run a task after networking goes up

  - by The Journeyman geek

  I'm working on moving my current server setup to newer hardware, and migrating from ubuntu karmic koala to lucid lynx. Currently i'm using gw6c (compiled from the gogo6 website, as opposed to the version from the repositories) to get ipv6 access for my systems. On the karmic koala system, i used simple init.d script to get the ipv6 client started #! /bin/sh /usr/local/gw6c/bin/gw6c -f /usr/local/gw6c/bin/gw6c.conf I figured since this runs at any runlevel, it should translate to respawn console none start on startup stop on shutdown script exec /usr/local/gw6c/bin/gw6c -f /usr/local/gw6c/bin/gw6c.conf emit free6_ipv6_started end script this works fine started from initctrl, but it apparently fails to start when it boots. - its status being stop/waiting. It works fine (and respawns) when started otherwise.Any ideas on where i'm going wrong, and what would be the appropriate 'start on' arguement? EDIT: the exact error is 'init: gw6c main process (xxx) ended with status 8' followed by the process respawning , with xxx being a PID i suspect. I'm also half suspecting this is cause gw6c starts before networking does, and i need my eth0 up before gw6c is

  Read the article

• No outbound internet connection after restarting CentOS 6.3

  - by wnstnsmth

  After restarting a headless CentOS 6.3 machine, it lost outbound internet connectivity, i.e. I can still connect to the server via SSH (ssh root@**.126.18.56), but stuff such as ping google.com gives google.com: unknown host, and yum list some_package gives a lot of network errors. This is what ifconfig gives: eth0 Link encap:Ethernet HWaddr 00:25:90:78:2D:5D inet addr:**.126.18.56 Bcast:**.126.18.255 Mask:255.255.255.0 inet6 addr: fe80::225:90ff:fe78:2d5d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:75594 errors:0 dropped:0 overruns:0 frame:0 TX packets:787 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7074741 (6.7 MiB) TX bytes:144391 (141.0 KiB) Interrupt:20 Memory:f7a00000-f7a20000 eth1 Link encap:Ethernet HWaddr 00:25:90:78:2D:5C UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:16 Memory:f7900000-f7920000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:504 (504.0 b) TX bytes:504 (504.0 b) I have absolutely no clue how to debug this, and I find it very strange since I can still connect via ssh. EDIT: Weirdly, /etc/resolv.conf does not contain any entries, or none that I can make sense of: # Generated by NetworkManager search sui-inter.net # No nameservers found; try putting DNS servers into your # ifcfg files in /etc/sysconfig/network-scripts like so: # # DNS1=xxx.xxx.xxx.xxx # DNS2=xxx.xxx.xxx.xxx # DOMAIN=lab.foo.com bar.foo.com So is it possible that rebooting the server erased that file? It worked before at least! And how do I solve this? By the way, pinging an IP address works.

  Read the article

• Allow connections to only a specific URL via HTTPS with iptables, -m recent (potentially) and -m string (definitely)

  - by The Consumer

  Hello, Let's say that, for example, I want to allow connections only to subdomain.mydomain.com; I have it partially working, but it sometimes gets in a freaky loop with the client key exchange once the Client Hello is allowed. Ah, to make it even more annoying, it's a self-signed certificate, and the page requires authentication, and HTTPS is listening on a non-standard port... So the TCP/SSL Handshake experience will differ greatly for many users. Is -m recent the right route? Is there a more graceful method to allow the complete TCP stream once the string is seen? Here's what I have so far: #iptables -N SSL #iptables -A INPUT -i eth0 -p tcp -j SSL #iptables -A SSL -m recent --set -p tcp --syn --dport 400 #iptables -A SSL -m recent --update -p tcp --tcp-flags PSH,SYN,ACK SYN,ACK --sport 400 #iptables -A SSL -m recent --update -p tcp --tcp-flags PSH,SYN,ACK ACK --dport 400 #iptables -A SSL -m recent --remove -p tcp --tcp-flags PSH,ACK PSH,ACK --dport 400 -m string --algo kmp --string "subdomain.mydomain.com" -j ACCEPT Yes, I have tried to get around this with nginx tweaks, but I can't get nginx to return a 444 or abrupt disconnect before the client hello, if you can think of a way to achieve this instead, I'm all ears, err, eyes. (As suggested by a user, bringing this inquiry over from http://stackoverflow.com/questions/4628157/allow-connections-to-only-a-specific-url-via-https-with-iptables-m-recent-pote)

  Read the article

• Mixing both local and nonlocal addresses on three switches

  - by klew

  I have four computers that have nonlocal addresses like 150.X.X.X. Now I also get another few computers that should be only accessible through a gateway (it will be computing cluster) and they addresses are 10.0.0.X. I also wanted to include those four older computers to this new cluster, but I want them to be accessible from internet on nonlocal addresses (so I would like to set up them on both 150.X.X.X and 10.0.0.X addresses - I've set up it as interface eth0:0 since I have only one NIC). Those new computers have their switch and old computers also have their own switch. Both of them are connected to another (third) switch. The problem is that those old computers see each other (I can ping them), and also new computers see each other, but I can't ping old computer from new computer and vice versa. However pinging on nonlocal adresses works as expected. I looked into switch configuration and didn't find anything useful. I have no idea what I missed here. Can somebody help? All computers have Ubuntu Server 10.04

  Read the article

• Route all traffic of home network through VPN

  - by user436118

  I have a typical semi advanced home network scenario: A cable modem - eth A wireless router (netgear n600) eth and wlan A home server (Running ubuntu 12.04 LTS, connected over wlan) A bunch of wireless clients (wlan) Lying around I have anoher cheaper wlan router, and two different USB wlan NIC's that are known to work with Linux. ACTA struck. I want to route ALL of my WAN traffic through a remote server through a VPN. For sake of completition, lets say there is a remote server running debian sqeeze where a VPN server is to be installed. The network is then to behave so that if the VPN is not operative, it is separated from the outside world. I am familiar with general system/network practices, but lack the specific detailed knowledge to accomplish this. Please suggest the right approach, packages and configurations you'd use to reach said solution. I've also envisioned the following network configuration, please improve it if you see fit: ==LAN== Client ip:10.1.1.x nm:255.0.0.0 gw:10.1.1.1 reached via WLAN Wlan router 1: ip: 10.1.1.1 nm:255.0.0.0 gw: 10.10.10.1 reached via ETH Homeserver: <<< VPN is initiated here, and the other endpoint is somewhere on the internet. eth0: ip:10.10.10.1 nm: 0.0.0.0 gw:192.168.0.1 reached via WLAN Homeserver: wlan0: ip: 192.168.0.2 nm: 255.255.255.0 gw: 192.168.0.1 reached via WLAN ==WAN== Wlan router 2: ip: 192.168.0.1 nm: 0.0.0.0 gw: set via dhcp uplink connector: cable modem Cable Modem: Remote DHCP. Has on-board DHCP server for ethernet device that connects to it, and only works this way. All this WLAN fussery is because my home server is located in a part of the house where a cable link isnt possible unfortunately.

  Read the article

• Why host and vmware guests fail to get MAC of each other?

  - by Georgiy Nemtsov

  I have Windows 7 64bit host running VmWare Workstation 8 with two CentOS 6.3 guests. All guests adaptors are bridged with statically assigned ip's. Connectivity bitween host and guests was fine for many days running this setup. And today while I was working suddenly host and guests became unreachable for each other. While both host and guests could connect to internet and connect to other mashines in my networks. On guests arp -a showed for host ip address: ? (192.168.1.3) <incomlete> on eth0 On host arp -a showed for guests ip 192.168.1.19 00-00-00-00-00-00 192.168.1.20 00-00-00-00-00-00 All other arp records was OK. Deleting arp-caches didn't help neither on guests nor on host. After that I disabled and reenabled network adaptor on my Windows 7 host. And the problem was gone. arp -a now shows correct MACs on all instances. As I suppose the issue was about expiry of arp cache. For some reason host and guests couldn't get their MACs. Hope somebody knows what it is all about? I am preparing guests to work in production and don't want to face such problems in future! Also I was supprised while investigating this issue from another mashine that could connect both on guests and host. On that mashine arp -a showed same MAC for host and two guests.

  Read the article

• iptables, forward traffic for ip not active on the host itself

  - by gucki

  I have kvm guest which's netword card is conntected to the host using a tap device. The tap device is part of a bridge on the host together with eth0 so it can access the public network. So far everything works, the guest can access the public network and it can be accessed from the public network. Now the kvm process on the host provides a vnc server for the guest which listens on 127.0.0.1:5901 on the host. Is there any way to make this vnc server accessible by the ip address which the guest is using (ex. 192.168.0.249), without interrupting the guest from using the same ip (port 5901 is not used by the guest)? It should also work when the guest is not using any ip address at all. So basically I just want to fake IP xx is on the host and only answer/ forward traffic to port 5901 to the host itself. I tried using this NAT rule on the host, but it doesn't work. Ip forwarding is enabled at the host. iptables -t nat -A PREROUTING -p tcp --dst 192.168.0.249 --dport 5901 -j DNAT --to-destination 127.0.0.1:5901 I assume this is because the IP 192.168.0.249 is not not bound to any interfaces and so no ARP requests for it get answered and so no packets for this IP arrive at the host. How can make it work? :)

  Read the article

• Route all traffic of home network through VPN [migrated]

  - by user436118

  I have a typical semi advanced home network scenario: A cable modem - eth A wireless router (netgear n600) eth and wlan A home server (Running ubuntu 12.04 LTS, connected over wlan) A bunch of wireless clients (wlan) Lying around I have anoher cheaper wlan router, and two different USB wlan NIC's that are known to work with Linux. ACTA struck. I want to route ALL of my WAN traffic through a remote server through a VPN. For sake of completition, lets say there is a remote server running debian sqeeze where a VPN server is to be installed. The network is then to behave so that if the VPN is not operative, it is separated from the outside world. I am familiar with general system/network practices, but lack the specific detailed knowledge to accomplish this. Please suggest the right approach, packages and configurations you'd use to reach said solution. I've also envisioned the following network configuration, please improve it if you see fit: Client ip:10.1.1.x nm:255.0.0.0 gw:10.1.1.1 reached via WLAN Wlan router 1: ip: 10.1.1.1 nm:255.0.0.0 gw: 10.10.10.1 reached via ETH Homeserver: <<< VPN is initiated here, and the other endpoint is somewhere on the internet. eth0: ip:10.10.10.1 nm: 0.0.0.0 gw:192.168.0.1 reached via WLAN Homeserver: wlan0: ip: 192.168.0.2 nm: 255.255.255.0 gw: 192.168.0.1 reached via WLAN Wlan router 2: ip: 192.168.0.1 nm: 0.0.0.0 gw: set via dhcp uplink connector: cable modem Cable Modem: Remote DHCP. Has on-board DHCP server for ethernet device that connects to it, and only works this way. All this WLAN fussery is because my home server is located in a part of the house where a cable link isnt possible unfortunately.

  Read the article

• Can't connect to wi-fi hotspot in Ubuntu 11.10

  - by ht3t

  I'm new to Ubuntu. I'm having a wireless network problem in Ubuntu 11.10. I made a hotspot using Connectify from a computer which is running Windows 7. I can access it in Windows 7 but not in Ubuntu 11.10. Every time I access it,I get a message "disconnected". I'm using msi fx 400 notebook with Intel Centrino wireless -N 1000 wireless card. Ubuntu version is 11.10 with KDE desktop. $ sudo lshw -c network [sudo] password for ht3t: *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:56:b8:f0 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:44 memory:e7400000-e7401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 40:61:86:b6:b1:a2 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw IP=192.168.21.107 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:9000(size=256) memory:e6004000-e6004fff memory:e6000000-e6003fff I can't do anything without internet connection. How can I fix this?

  Read the article

• Can you explain how to understand what the 'iwconfig' command displays in Ubuntu-9.04?

  - by Shawn

  I'm having trouble making my wireless connection work, and I realized I don't really know how to use the tools I have, in this case, the iwconfig command in Ubuntu-9.04. Here is what I get: ***iwconfig*** - lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Network" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=20 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 vboxnet0 no wireless extensions. pan0 no wireless extensions. "Network" is the name of my wireless network, btw. But what does this all mean? How can this information help me aquire a working wireless connection? When I try associating a key using sudo iwconfig wlan0 key s:my_key I get the following error message: Error for wireless request "Set Encode" (8B2A) : SET failed on device wlan0 ; Invalid argument. I do have the right key though, so what's the problem?

  Read the article

• How to set up vpn tunnel (ipsec) connection

  - by Alfwed

  I'm working with a client who wants to set up a vpn tunnel between their network and ours. They're in charge of the tunnel and to give us the access they are asking me my public IP and my LAN IP. This is what i've got when i do an ifconfig on the server i will use to connect to the vpn $ ifconfig eth0 Link encap:Ethernet HWaddr d4:ae:52:cd:xx:xx inet adr:62.210.xxx.xxx Bcast:62.210.xxx.xxx Masque:255.255.255.0 adr inet6: fe80::d6ae:52ff:xxxx:xx/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:55255032 erreurs:0 :779628 overruns:0 frame:0 TX packets:5419527 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:5598164393 (5.5 GB) Octets transmis:1034297288 (1.0 GB) Interruption:16 Mémoire:c0000000-c0012800 lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 Packets reçus:45923382 erreurs:0 :0 overruns:0 frame:0 TX packets:45923382 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 The inet adr:62.210.xxx.xxx is my public IP but it seems like i dont have any LAN IP. Can the connection work without LAN IP or should I create a private network somehow?

  Read the article

• Can you explain how to understand what the 'iwconfig' command displays in Ubuntu-9.04?

  - by Shawn

  I'm having trouble making my wireless connection work, and I realized I don't really know how to use the tools I have, in this case, the iwconfig command in Ubuntu-9.04. Here is what I get: ***iwconfig*** - lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Network" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=20 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 vboxnet0 no wireless extensions. pan0 no wireless extensions. "Network" is the name of my wireless network, btw. But what does this all mean? How can this information help me aquire a working wireless connection? When I try associating a key using sudo iwconfig wlan0 key s:my_key I get the following error message: Error for wireless request "Set Encode" (8B2A) : SET failed on device wlan0 ; Invalid argument. I do have the right key though, so what's the problem?

  Read the article

• Renaming VLAN Interfaces in Linux

  - by rhololkeolke

  I need to know how to rename VLAN interfaces. I'm currently running Ubuntu 11.04. I'm running a networking application that takes frames on one interface applies things like delays and errors and then forwards the frames out another interface. The default naming convention which names things <interface>.<vlan> e.g. eth0.2 will not work for my purposes because the program which parses the configuration script for the networking application doesn't like the decimal in the interface name. I ran vconfig set_name_type VLAN_PLUS_VID which solves the decimal in the interface name problem, however, I can then no longer assign the same vlan id to multiple interfaces because they have the same name. I know how to change physical interface names using udev rules, but because the vlan's will have the same MAC address and they aren't physical interfaces I can't use those rules to rename the interfaces. Is there a way to rename any interface in linux, including the virtual ones? Is there a way to specify your own naming convention for config set_name_type option without having to recompile the source of vconfig?

  Read the article

• Installer Reboots at "Detecting hardware" (disks and other hardware) on all recent Server Installs

  - by Ryan Rosario

  I have a very frustrating problem with my PC. I cannot install any recent version of Ubuntu Server (or even Desktop) since 9.04 even using the text-based installer. I boot from a USB stick created by Unetbootin (I also tried other methods such as startup disk creator with no difference). On the Server installer, it gets to "Detecting Hardware" (the second one about disks and all other hardware, not network hardware) and then either hangs at 0% (waited 24 hours), or reboots after a minute or two. My system (late 2007): ASUS P5NSLI motherboard Intel Core 2 Duo E6600 2.4Ghz 2 x 1GB Corsair 667MHz RAM nVidia GeForce 6600 I have unplugged everything (including the only hard disk, CD-ROMs and floppy). I have only one stick of RAM (tried each one to no avail) and am booting the installer from a USB stick (booting from CD-ROM yields the same problem). I also tried several of the boot options (nomodeset, nousb, acpi=off, noapic, i915.modeset=1/0, xforcevesa) in all combinations) to no avail. The only active parts of my system are the video card, mouse, keyboard and USB stick. I have also updated the BIOS to the most recent version. (FWIW, on the Desktop installer, I get a black screen after hitting the Install option.) Even after removing "quiet" I am unable to see what kernel panic is occurring (or not occurring) to cause the install to crash. I am only able to save the debug logs via a simple webserver in the installer. After the last line (I repeatedly refreshed), the server stops responding and the installer hangs or reboots: Jan 2 01:04:03 main-menu[302]: INFO: Menu item 'disk-detect' selected Jan 2 01:04:04 kernel: [ 309.154372] sata_nv 0000:00:0e.0: version 3.5 Jan 2 01:04:04 kernel: [ 309.154409] sata_nv 0000:00:0e.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.154531] sata_nv 0000:00:0e.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.164442] scsi0 : sata_nv Jan 2 01:04:04 kernel: [ 309.167610] scsi1 : sata_nv Jan 2 01:04:04 kernel: [ 309.167762] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 10 Jan 2 01:04:04 kernel: [ 309.167774] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 10 Jan 2 01:04:04 kernel: [ 309.167948] sata_nv 0000:00:0f.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.168071] sata_nv 0000:00:0f.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.171931] scsi2 : sata_nv Jan 2 01:04:04 kernel: [ 309.173793] scsi3 : sata_nv Jan 2 01:04:04 kernel: [ 309.173943] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 11 Jan 2 01:04:04 kernel: [ 309.173954] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 11 Jan 2 01:04:04 kernel: [ 309.174061] pata_amd 0000:00:0d.0: version 0.4.1 Jan 2 01:04:04 kernel: [ 309.174160] pata_amd 0000:00:0d.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.177045] scsi4 : pata_amd Jan 2 01:04:04 kernel: [ 309.178628] scsi5 : pata_amd Jan 2 01:04:04 kernel: [ 309.178801] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 Jan 2 01:04:04 kernel: [ 309.178811] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface eth0 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface lo Jan 2 01:04:04 kernel: [ 309.485062] ata3: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:04 kernel: [ 309.633094] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Jan 2 01:04:04 kernel: [ 309.641647] ata1.00: ATA-8: ST31000528AS, CC38, max UDMA/133 Jan 2 01:04:04 kernel: [ 309.641658] ata1.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 31/32) Jan 2 01:04:04 kernel: [ 309.657614] ata1.00: configured for UDMA/133 Jan 2 01:04:04 kernel: [ 309.657969] scsi 0:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5 Jan 2 01:04:04 kernel: [ 309.658482] sd 0:0:0:0: Attached scsi generic sg0 type 0 Jan 2 01:04:04 kernel: [ 309.658588] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Jan 2 01:04:04 kernel: [ 309.658812] sd 0:0:0:0: [sda] Write Protect is off Jan 2 01:04:04 kernel: [ 309.658823] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Jan 2 01:04:04 kernel: [ 309.658918] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 2 01:04:04 kernel: [ 309.675630] sda: sda1 sda2 Jan 2 01:04:04 kernel: [ 309.676440] sd 0:0:0:0: [sda] Attached SCSI disk Jan 2 01:04:05 kernel: [ 309.969102] ata2: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:05 kernel: [ 310.281137] ata4: SATA link down (SStatus 0 SControl 300) Anybody have any additional ideas I could try? I am getting ready to just toss the motherboard.

  Read the article

• Determining Maximum Txpower a WiFi Card Supports?

  - by BigGenius

  I have a Atheros R9285 wifi card. How can i determine , what is max. Txpower it can support? biggenius@hackbook:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Default" Mode:Managed Frequency:2.437 GHz Access Point: 00:08:5C:9D:4F:40 Bit Rate=2 Mb/s Tx-Power=35 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=24/70 Signal level=-86 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:140 Invalid misc:247 Missed beacon:0 eth0 no wireless extensions. biggenius@hackbook:~$ iw phy0 info Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (35.0 dBm) * 2417 MHz [2] (35.0 dBm) * 2422 MHz [3] (35.0 dBm) * 2427 MHz [4] (35.0 dBm) * 2432 MHz [5] (35.0 dBm) * 2437 MHz [6] (35.0 dBm) * 2442 MHz [7] (35.0 dBm) * 2447 MHz [8] (35.0 dBm) * 2452 MHz [9] (35.0 dBm) * 2457 MHz [10] (35.0 dBm) * 2462 MHz [11] (35.0 dBm) * 2467 MHz [12] (35.0 dBm) * 2472 MHz [13] (35.0 dBm) * 2484 MHz [14] (35.0 dBm) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Band 2: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 5180 MHz [36] (35.0 dBm) * 5200 MHz [40] (35.0 dBm) * 5220 MHz [44] (35.0 dBm) * 5240 MHz [48] (35.0 dBm) * 5260 MHz [52] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5280 MHz [56] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5300 MHz [60] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5320 MHz [64] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5500 MHz [100] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5520 MHz [104] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5540 MHz [108] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5560 MHz [112] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5580 MHz [116] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5600 MHz [120] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5620 MHz [124] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5640 MHz [128] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5660 MHz [132] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5680 MHz [136] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5700 MHz [140] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5745 MHz [149] (35.0 dBm) * 5765 MHz [153] (35.0 dBm) * 5785 MHz [157] (35.0 dBm) * 5805 MHz [161] (35.0 dBm) * 5825 MHz [165] (35.0 dBm) Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ managed, WDS, P2P-client } <= 2048, #{ AP, mesh point, P2P-GO } <= 8, total <= 2048, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (82) * Unknown command (81) * Unknown command (84) * Unknown command (87) * Unknown command (85) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS.

  Read the article

• Realtek RTL8111/8168B wired network doesn't work anymore

  - by Radar4002

  This sounds like it's a common problem upgrading 11.04, but I am having trouble finding a common solution, and one that will work for me. I just applied updates via the update manager and now my wired network connection is down. I know Ubuntu network settings is the issue, because I have a dual-boot with Win 7 and my network/internet is fine on Win 7. I don't know too much about networking, so what can I do to trouble shoot this issue? I can choose an older grub version, 2.6.38-8 instead of 2.6.38-11 and this does not resolve the issue. Here is my lspci result: 00:00.0 Host bridge: ATI Technologies Inc RD890 Northbridge only single slot PCI-e GFX Hydra part (rev 02) 00:02.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port B) 00:04.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port D) 00:05.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port E) 00:06.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port F) 00:07.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port G) 00:09.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port H) 00:0a.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (external gfx1 port A) 00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] (rev 40) 00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 41) 00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40) 00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:15.0 PCI bridge: ATI Technologies Inc Device 43a0 00:16.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:16.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control 01:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5700 Series] 01:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 02:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 07:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 07:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 08:0e.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) 09:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) 09:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) Here is my sudo lshw -class network: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 03 serial: 6c:f0:49:e7:72:e8 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:40 ioport:9e00(size=256) memory:fceff000-fcefffff memory:fcef8000-fcefbfff memory:fce00000-fce1ffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth1 version: 03 serial: 6c:f0:49:e7:72:ea size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:47 ioport:8e00(size=256) memory:fddff000-fddfffff memory:fddf8000-fddfbfff memory:fdd00000-fdd1ffff

  Read the article

• Atheros AR9485 wireless card doesn't work in an ASUS K53E

  - by John

  I just installed Ubuntu 11.10 32-bit version in dual boot mode on an ASUS K53. Every thing seems to work fine except for the wireless. The wireless works on Windows 7. Ubuntu finds the wireless card, but it does not appear to be turned on. The only physical means of turning on the card is the FN-F2 key combo. That works on Windows, but not in Ubuntu. I've looked in the forums for a solution and I'm not quite sure what to do. I've gathered the following information: jdwbmc@Spatha:~$ cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10" Linux Spatha 3.0.0-12-generic #20-Ubuntu SMP Fri Oct 7 14:50:42 UTC 2011 i686 i686 i386 GNU/Linux jdwbmc@Spatha:~$ lspci -nnk | grep -iA2 net 02:00.0 Network controller [0280]: Atheros Communications Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01) Subsystem: AzureWave Device [1a3b:1186] Kernel driver in use: ath9k -- 04:00.0 Ethernet controller [0200]: Atheros Communications AR8151 v2.0 Gigabit Ethernet [1969:1083] (rev c0) Subsystem: ASUSTeK Computer Inc. Device [1043:1851] Kernel driver in use: atl1c jdwbmc@Spatha:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 058f:a014 Alcor Micro Corp. jdwbmc@Spatha:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff jdwbmc@Spatha:~$ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no jdwbmc@Spatha:~$ lsmod Module Size Used by parport_pc 32114 0 ppdev 12849 0 snd_hda_codec_hdmi 31426 1 bnep 17923 2 rfcomm 38408 0 bluetooth 148839 10 bnep,rfcomm snd_hda_codec_realtek 254125 1 binfmt_misc 17292 1 joydev 17393 0 asus_nb_wmi 12469 0 asus_wmi 19333 1 asus_nb_wmi sparse_keymap 13658 1 asus_wmi uvcvideo 67271 0 videodev 85626 1 uvcvideo snd_hda_intel 24262 2 snd_hda_codec 91754 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_i ntel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80468 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 wmi 18744 1 asus_wmi snd_rawmidi 25241 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event arc4 12473 2 i915 505108 3 snd_timer 28932 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq ath9k 112711 0 psmouse 73673 0 serio_raw 12990 0 mac80211 272785 1 ath9k drm_kms_helper 32889 1 i915 ath9k_common 13599 1 ath9k drm 192226 4 i915,drm_kms_helper ath9k_hw 293893 2 ath9k,ath9k_common ath 19387 2 ath9k,ath9k_hw cfg80211 172392 3 ath9k,mac80211,ath snd 55902 14 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_i ntel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,s nd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd snd_page_alloc 14115 2 snd_hda_intel,snd_pcm mei 36466 0 i2c_algo_bit 13199 1 i915 video 18908 1 i915 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp ahci 21634 3 libahci 25727 1 ahci atl1c 36638 0 xhci_hcd 72915 0 jdwbmc@Spatha:/var/lib/NetworkManager$ cat NetworkManager.state [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true jdwbmc@Spatha:~$ lspci -nn | grep 0280 02:00.0 Network controller [0280]: Atheros Communications Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01) Any help would be appreciated. Thanks.

  Read the article

• wifi hardware switch doesn't work on a Dell 1018

  - by user42566

  I have a problem with my Dell 1018 Inspiron. I can't switch the wifi on, through the key on the keyboard. I think it's a driver problem since Ubuntu 11.10. This are the versions i tried: Ubuntu 10.04 / 10.10 It's possible to install the driver by hand: sudo add-apt-repository ppa:lexical/hwe-wireless sudo apt-get update sudo apt-get install rtl8192ce-dkms Ubuntu 11.04 It works out of the box Ubuntu 11.10 / 12.04 I haven’t found any solution for these versions. The "ppa:lexical/hwe-wireless" doesn't work for these versions. It says Can not find package rtl8192ce-dkms. The window of additional drivers is empty. So I can't install the driver. The wired network works good. Here is some information: 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes sudo lshw -class network *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 5c:26:0a:0d:20:10 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0f2c000-f0f2cfff memory:f0f18000-f0f1bfff *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 01 serial: 70:f1:a1:fe:15:bd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.2.0-22-generic-pae firmware=N/A ip=192.168.1.76 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 ioport:3000(size=256) memory:f0100000-f0103fff mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation N10 Family DMI Bridge [8086:a010] 00:02.0 VGA compatible controller [0300]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a011] 00:02.1 Display controller [0380]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a012] 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02) 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02) 00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 02) 00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) 00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) 00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) 00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) 00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) 00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 07:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 174f:1127 Syntek mark@mark-Inspiron-1018:~$

  Read the article

• Why does Ubuntu only detect one USB LAN adapters at a time?

  - by EGO

  I try to connect real switch with my computer for an exam preparation, for this purpose I need more than one LAN cards, and there is only one built in LAN card in my computer. So, to get more LAN cards, I bought 4 USB Ethernet adapters (as I have 4 usb ports in may laptop 2 usb 2.0 ports, 2 usb 3.0 ports). When I plug these adapters in my computer Ubuntu only detects one LAN card from 2.0 usb ports, and one LAN card from 3.0 ports. And sometimes detects only one USB LAN from all the usb ports. Actually the real problem is Ubuntu shows these USB LAN adapters in the "lsusb", but does not list them in "ifconfig". Kontron (Industrial Computer Source / ICS Advent) is my LAN USB ethernet. abc@ubuntu:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hu Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hu Bus 002 Device 012: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 001 Device 003: ID 138a:0018 Validity Sensors, Inc. Bus 001 Device 004: ID 064e:e258 Suyin Corp. Bus 003 Device 011: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 002 Device 013: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 003 Device 012: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 002 Device 005: ID 0a5c:21b4 Broadcom Corp. BCM2070 Bluetooth 2.1 + EDR -- etho is my built in LAN card, while eth1 is the only USB LAN card that ubuntu has detected. abc@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 2c:27:d7:a5:d2:39 inet6 addr: fe80::2e27:d7ff:fea5:d239/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:21056 errors:0 dropped:1 overruns:0 frame:0 TX packets:5669 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1407289 (1.4 MB) TX bytes:372566 (372.5 KB) Interrupt:49 Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:e0:4c:53:44:58 inet6 addr: fe80::2e0:4cff:fe53:4458/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:9230 errors:0 dropped:0 overruns:0 frame:0 TX packets:9230 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:557648 (557.6 KB) TX bytes:557648 (557.6 KB) wlan0 Link encap:Ethernet HWaddr cc:52:af:5e:78:05 inet addr:192.168.1.65 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::ce52:afff:fe5e:7805/64 Scope:LinkU UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:17389 errors:0 dropped:0 overruns:0 frame:0 TX packets:12231 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22452248 (22.4 MB) TX bytes:1502750 (1.5 MB) If I unplug the USB LAN card which Ubuntu has detected, then Ubuntu will detect a USB LAN card from the remaining plugged adapters, and process go on untill I plug all the USB LAN adapters. Looking for some urgent help. Thanks

  Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59  | Next Page >