Search Results

Search found 1454 results on 59 pages for 'eth0'.

Page 55/59 | < Previous Page | 51 52 53 54 55 56 57 58 59  | Next Page >

• Secure ldap problem

  - by neverland

  Hi there, I have tried to config my openldap to have secure connection by using openssl on Debian5. By the way, I got trouble during the below command. ldap:/etc/ldap# slapd -h 'ldap:// ldaps://' -d1 >>> slap_listener(ldaps://) connection_get(15): got connid=7 connection_read(15): checking for input on id=7 connection_get(15): got connid=7 connection_read(15): checking for input on id=7 connection_get(15): got connid=7 connection_read(15): checking for input on id=7 connection_get(15): got connid=7 connection_read(15): checking for input on id=7 connection_read(15): unable to get TLS client DN, error=49 id=7 connection_get(15): got connid=7 connection_read(15): checking for input on id=7 ber_get_next ber_get_next on fd 15 failed errno=0 (Success) connection_closing: readying conn=7 sd=15 for close connection_close: conn=7 sd=15 Then I have search for "unable to get TLS client DN, error=49 id=7" but it seems no where has a good solution to this yet. Please help. Thanks # Well, I try to fix something to get it work but now I got this ldap:~# slapd -d 256 -f /etc/openldap/slapd.conf @(#) $OpenLDAP: slapd 2.4.11 (Nov 26 2009 09:17:06) $ root@SD6-Casa:/tmp/buildd/openldap-2.4.11/debian/build/servers/slapd could not stat config file "/etc/openldap/slapd.conf": No such file or directory (2) slapd stopped. connections_destroy: nothing to destroy. What should I do now? log : ldap:~# /etc/init.d/slapd start Starting OpenLDAP: slapd - failed. The operation failed but no output was produced. For hints on what went wrong please refer to the system's logfiles (e.g. /var/log/syslog) or try running the daemon in Debug mode like via "slapd -d 16383" (warning: this will create copious output). Below, you can find the command line options used by this script to run slapd. Do not forget to specify those options if you want to look to debugging output: slapd -h 'ldaps:///' -g openldap -u openldap -f /etc/ldap/slapd.conf ldap:~# tail /var/log/messages Feb 8 16:53:27 ldap kernel: [ 123.582757] intel8x0_measure_ac97_clock: measured 57614 usecs Feb 8 16:53:27 ldap kernel: [ 123.582801] intel8x0: measured clock 172041 rejected Feb 8 16:53:27 ldap kernel: [ 123.582825] intel8x0: clocking to 48000 Feb 8 16:53:27 ldap kernel: [ 131.469687] Adding 240932k swap on /dev/hda5. Priority:-1 extents:1 across:240932k Feb 8 16:53:27 ldap kernel: [ 133.432131] EXT3 FS on hda1, internal journal Feb 8 16:53:27 ldap kernel: [ 135.478218] loop: module loaded Feb 8 16:53:27 ldap kernel: [ 141.348104] eth0: link up, 100Mbps, full-duplex Feb 8 16:53:27 ldap rsyslogd: [origin software="rsyslogd" swVersion="3.18.6" x-pid="1705" x-info="http://www.rsyslog.com"] restart Feb 8 16:53:34 ldap kernel: [ 159.217171] NET: Registered protocol family 10 Feb 8 16:53:34 ldap kernel: [ 159.220083] lo: Disabled Privacy Extensions

  Read the article

• Archlinux/atheros WLAN configuration troubles

  - by GrinReaper

  I'm trying to config archlinux to use my wireless network adapter. It's quite troublesome. From what I've gathered, it's an atheros network adapter, using the ath5k driver/module... I can't get it to work; any ideas? Here's some of the output from my tinkering: # lspci | grep -i net 00:0a.0 Ethernet controller: nVidia corporation MCP67 Ethernet (reva2) 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) # lsusb ... Bus 004 Device 003: ID 03f0:17d Hewlett Packard Wireless (Bluetooth + WLAN Interface [Integrated Module] # ping -c 3 www.google.com ping: unknown host www.google.com #ping -c 3 8.8.8.8 ping: network is unreachable # lspci -v 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) ... Kernel driver in use: ath5k Kernel modules: ath5k # dmesg |grep ath5k registered as phy0 registered led device ath5k: atheros chip found PCI INT A disabled registered led device registered as phy1 # ip addr | sed '/^[0-9]/!d;s/: <.*$//' 1: lo 2: eth1 3: eth0 # ip link set <interface> up/down RNETLINK answers: Operation not possible due to RF-kill Also, is there a way to dump text from command-line to a text file so i can just copy pasta? Sorry, first time using a linux distro... EDIT: So I just tried this: I actually just did this twice. (I can't tell which setting is on/off for my wireless adapter. The lights are blue all the time now.) #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :yes 1: hp-bluetooth: bluetooth softblocked: no hardblocked :yes 3: phy1: wireless lan softblocked: no hardblocked :yes #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :no 1: hp-bluetooth: bluetooth softblocked: no hardblocked no 3: phy1: wireless lan softblocked: no hardblocked :yes 7: hci0: bluetooh 0: hp-wifi: wireless lan softblocked: no hardblocked :no I've dug around some other articles and it seems like ath5k is supposed to be preferable to madwifi, so should i be using madwifi? I'm 99% sure I disabled the hardblock (by turning it ON) but, as shown above, phy1 wireless lan is STILL hardblocked. What gives? Maybe I've made some more fundamental error in a basic config file? EDIT: I've fixed the hardblock. I've tried pinging www.google.com, but to no avail. I get: ping: unknown host www.google.com In the arch wiki: Edit /etc/hosts and add the same HOSTNAME you entered in /etc/rc.conf: 127.0.0.1 archlinux.domain.org localhost.localdomain localhost archlinux To my understanding, hostname is just a user-specified and based on preference(?) My /etc/rc.conf: HOSTNAME="gestalt" My /etc/hosts: 127.0.0.1 localhost.localdomain localhost gestalt but should it be the following? 120.0.0.1 localhost.domain.org localhost.localdomain localhost gestalt

  Read the article

• Mysql server fails to start

  - by Nicolas Thery

  Googling since two hours, I require your assistance. I'm on a Debian virtual machine and I cloned it. The only change is the new IP adress it has. Mysql doesn't start any more: Starting MySQL database server: mysqld . . . . . . . . . . . . . . failed! There is no process called mysql. All the mysql log files in /var/log are empty. here is my.cnf file : [client] port = 3306 socket = /var/run/mysqld/mysqld.sock [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp language = /usr/share/mysql/english skip-external-locking bind-address = 127.0.0.1 key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 myisam-recover = BACKUP query_cache_limit = 1M query_cache_size = 16M general_log_file = /var/log/mysql/mysql.log log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] [isamchk] key_buffer = 16M [mysqld_safe] syslog Here is the result of ifconfig : eth0 Link encap:Ethernet HWaddr 00:0c:29:12:98:9a inet adr:192.168.1.138 Bcast:192.168.1.255 Masque:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:754 errors:0 dropped:0 overruns:0 frame:0 TX packets:106 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 RX bytes:101177 (98.8 KiB) TX bytes:17719 (17.3 KiB) lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 RX bytes:560 (560.0 B) TX bytes:560 (560.0 B) As requested, here is the result of : sudo -u mysql mysqld, here is the result : root@debian:/home/nicolas/Bureau# sudo -u mysql mysqld 121004 14:26:57 [Note] Plugin 'FEDERATED' is disabled. mysqld: Can't find file: './mysql/plugin.frm' (errno: 13) 121004 14:26:57 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 121004 14:26:57 InnoDB: Initializing buffer pool, size = 8.0M 121004 14:26:57 InnoDB: Completed initialization of buffer pool 121004 14:26:57 InnoDB: Started; log sequence number 0 70822697 121004 14:26:57 [Note] Recovering after a crash using /var/log/mysql/mysql-bin 121004 14:26:57 [Note] Starting crash recovery... 121004 14:26:57 [Note] Crash recovery finished. 121004 14:26:57 [ERROR] mysqld: Can't find file: './mysql/host.frm' (errno: 13) 121004 14:26:57 [ERROR] Fatal error: Can't open and lock privilege tables: Can't find file: './mysql/host.frm' (errno: 13)

  Read the article

• FTP could not connect after applying local DNS(private DNS)

  - by Rahul

  I made a software router in CentOS linux and in that made a DNS server. I am using centOS 6..4 for making DNS i applied following steps: changed the host name = abc.zoom.com and domain name = zoom.com. then did changes in the named.rfc.1912 file as per rename named.localhost = forward and named.loopback = reverse in forward lookups i changed zone "zoom.com" IN { type master; file "forward"; allow-update { none; }; and in reverse lookups i changed zone "x.168.192.in-addr.arpa" IN { type master; file "reverse"; allow-update { none; }; and then did changes in the named.conf file options { listen-on port 53 {192.168.x.x;}; listen-on-v6 port 53 { ::1; }; directory "/var/named"; dump-file "/var/named/data/cache_dump.db"; statistics-file "/var/named/data/named_stats.txt"; memstatistics-file "/var/named/data/named_mem_stats.txt"; allow-query {any;}; recursion yes; 192.168.x.x is my local DNS address. then i copied lookups file in /var/named and edited the file "forward" $TTL 1D @ IN SOA abc.zoom.com. rahul.abc.zoom.com. ( 0 ; serial 1D ; refresh 1H ; retry 1W ; expire 3H ) ; minimum NS abc.zoom.com. abc A 192.168.x.x and for " reverse" $TTL 1D @ IN SOA abc.zoom.com. rahul.abc.zoom.com.( 0 ; serial 1D ; refresh 1H ; retry 1W ; expire 3H ) ; minimum NS abc.zoom.com. x PTR abc.zoom.com. when i put the public ip details in the Eth0 it was automatically redirect in to the resolve.conf when i checked through dig command the answer, query all were 1. my system is itself a Software router.In gateway of my all local machine i give my system ip address. however my DNS and Gateway IP is same. Now the problem is that. i gave the static ips to all my local machines when i give the DNS which i made i.e 192.168.x.x that time my ftp is not connect in filezilla software E.g: host : pqr.zoom.com ("zoom.com" is my local domain name) username : pqr password : pqr gives an error: Error: Connection timed out Error: Could not connect to server but if i give the public DNS address it get connected. i want to solve this problem please give solution on this.

  Read the article

• Specifying network settings during SLES 11 auto installation

  - by banjer

  I'm setting up an autoinst.xml file for auto-installing SLES 11. I get prompted for the various interface settings per below, but they don't seem to stick once the server reboots. I don't think I have the xml defined correctly. I'm hoping someone has experience with this. <ask-list> <ask> <path>networking,dns,hostname</path> <question>Enter Hostname (server name)</question> <stage>initial</stage> <default>merkin</default> </ask> <ask> <path>networking,interfaces,interface,0,device</path> <question>Enter the primary ethernet device:</question> <stage>initial</stage> <default>eth0</default> </ask> <ask> <path>networking,interfaces,interface,0,ipaddr</path> <question>Enter the primary IP Address:</question> <stage>initial</stage> </ask> <ask> <path>networking,interfaces,interface,0,netmask</path> <question>Enter the Netmask Address:</question> <stage>initial</stage> </ask> <ask> <path>networking,routing,routes,route,0,gateway</path> <question>Enter the primary Gateway Address:</question> <stage>initial</stage> </ask> </ask-list> The first one for hostname seems to be sticking just fine, but the rest do not. As an alternative, is there a way to stop the autoinstall at the section where you configure the network devices so that the user can take over? I was able to show the partition proposal, but not sure how to do the same with the networking setup.

  Read the article

• umount bind of stale NFS

  - by Paul Eisner

  i've got a problem removing mounts created with mount -o bind from a locally mounted NFS folder. Assume the following mount structure: NFS mounted directory: $ mount -o rw,soft,tcp,intr,timeo=10,retrans=2,retry=1 \ 10.20.0.1:/srv/source /srv/nfs-source Bound directory: $ mount -o bind /srv/nfs-source/sub1 /srv/bind-target/sub1 Which results in this mount map $ mount /dev/sda1 on / type ext3 (rw,errors=remount-ro) # ... 10.20.0.1:/srv/source on /srv/nfs-source type nfs (rw,soft,tcp,intr,timeo=10,retrans=2,retry=1,addr=10.20.0.100) /srv/nfs-source/sub1 on /srv/bind-target/sub1 type none (rw,bind) If the server (10.20.0.1) goes down (eg ifdown eth0), the handles become stale, which is expected. I can now un-mount the NFS mount with force $ umount -f /srv/nfs-source This takes some seconds, but works without any problems. However, i cannot un-mount the bound directory in /srv/bind-target/sub1. The forced umount results in: $ umount -f /srv/bind-target/sub1 umount2: Stale NFS file handle umount: /srv/bind-target/sub1: Stale NFS file handle umount2: Stale NFS file handle Here is a trace http://pastebin.com/ipvvrVmB I've tried umounting the sub-directories beforehand, find any processes accessing anything within the NFS or bind mounts (there are none). lsof also complains: $ lsof -n lsof: WARNING: can't stat() nfs file system /srv/nfs-source Output information may be incomplete. lsof: WARNING: can't stat() nfs file system /srv/bind-target/sub1 (deleted) Output information may be incomplete. lsof: WARNING: can't stat() nfs file system /srv/bind-target/ Output information may be incomplete. I've tried with recent stable Linux kernels 3.2.17, 3.2.19 and 3.3.8 (cannot use 3.4.x, cause need the grsecurity patch, which is not, yet, supported - grsecurity is not patched in in the tests above!). My nfs-utils are version 1.2.2 (debian stable). Does anybody have an idea how i can either: force the un-mount some other way? (any dirty trick is welcome, data loss or damage neglible at this point) use something else instead of mount -o bind? (cannot use soft links, cause mounted directories will be used in chroot; bindfs via FUSE is far to slow to be an option) Thanks, Paul Update 1 With 2.6.32.59 the umount of the (stale) sub-mounts work just fine. It seems to be a kernel regression bug. The above tests where with NFSv3. Additional tests with NFSv4 showed no change. Update 2 We have tested now multiple 2.6 and 3.x kernels and are now sure, that this was introduced in 3.0.x. We will fille a bug report, hopefully they figure it out.

  Read the article

• Connecting to localhost resolves 127.0.0.1 but connects with external IP [Linux, Debian]

  - by skgsergio

  I'm having a problem with a dedicated server, I don't known if it's the default behavior but this is the problem: If I connect to a service located on the server with localhost the service gets as source IP the external IP. Let me show an example, I use netcat for listening on 127.0.0.1:4444 xxxxxx # nc -vv -l -s 127.0.0.1 -p 4444 listening on [127.0.0.1] 4444 ... Lets check if it's ok: xxxxxx ~ # netstat -atnp | grep 4444 tcp 0 0 127.0.0.1:4444 0.0.0.0:* LISTEN 14038/nc Ok lets connect: xxxxxx ~ # nc -vv 127.0.0.1 4444 localhost [127.0.0.1] 4444 (?) open Return to the tty that have the listening process and I get this: connect to [127.0.0.1] from xxxxxx.net [176.31.xxx.xx] 50354 So that's the problem. I have a server daemon that have to listen on localhost and checks that the ip is 127.0.0.1 when the client connects but for some reason when I connect to localhost it reports the external ip... If I do the same with IPv6 it works as excepted... Detects connection as localhost (::1). Some info that can be useful: "localhost" resolves without problems to 127.0.0.1 xxxxxx ~ # ping -c1 localhost PING localhost (127.0.0.1) 56(84) bytes of data. 64 bytes from localhost (127.0.0.1): icmp_req=1 ttl=64 time=0.086 ms Nothing weird on my hosts file, I think... xxxxxx ~ # grep -v ^# /etc/hosts 127.0.0.1 localhost localhost.localdomain 176.31.xxx.xx xxxxxx.net ns1.xxxxxx.net ::1 ip6-localhost ip6-loopback feo0::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts And ifconfig reports all ok... eth0 Link encap:Ethernet HWaddr e0:69:95:d8:30:a1 inet addr:176.31.xxx.xx Bcast:176.31.108.255 Mask:255.255.255.0 inet6 addr: 2001:41d0:8:xxxx::/64 Scope:Global inet6 addr: 2001:41d0:8:xxxx:x:xx:xx:xx/64 Scope:Global inet6 addr: fe80::e269:95ff:fed8:30a1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16916 errors:0 dropped:0 overruns:0 frame:0 TX packets:16914 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8410679 (8.0 MiB) TX bytes:10539881 (10.0 MiB) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:5570 errors:0 dropped:0 overruns:0 frame:0 TX packets:5570 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:744490 (727.0 KiB) TX bytes:744490 (727.0 KiB)

  Read the article

• Weird DNS bug - external server resolves to internal IP

  - by emilecantin

  I have a server that is hosted by my university. I have root access, but no control over network setup, firewall, etc. This server's DNS resolves to an internal IP here on campus (10.x.x.x), and an external IP outside campus. I also have a few servers hosted at Amazon, and they mostly work well. However, one of them started to resolve the university server by its internal IP address. This causes problems, as 10.x.x.x on Amazon EC2 is someone else. I have connected to the Amazon server with SSH agent forwarding a few times in the past, to access a Git repository on the university server. Any idea what could cause this? EDIT: Here's my /etc/resolv.conf # Generated by dhcpcd for interface eth0 search ec2.internal nameserver 172.16.0.23 Here's the output of dig myserver.myuniversity.ca.: ; <<>> DiG 9.8.1-P1 <<>> myserver.myuniversity.ca. ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 34470 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;myserver.myuniversity.ca. IN A ;; ANSWER SECTION: myserver.myuniversity.ca. 537586 IN A 10.43.x.x ;; Query time: 2 msec ;; SERVER: 172.16.0.23#53(172.16.0.23) ;; WHEN: Wed Nov 28 16:07:21 2012 ;; MSG SIZE rcvd: 60 Here's the expected output (on another Amazon server): ; <<>> DiG 9.8.1-P1 <<>> myserver.myuniversity.ca. ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 8045 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;myserver.myuniversity.ca. IN A ;; ANSWER SECTION: myserver.myuniversity.ca. 601733 IN A x.x.239.1 ;; Query time: 1 msec ;; SERVER: 172.16.0.23#53(172.16.0.23) ;; WHEN: Wed Nov 28 16:09:36 2012 ;; MSG SIZE rcvd: 60

  Read the article

• Forwarding RDP via a Linux machine using iptables: Not working

  - by Nimmy Lebby

  I have a Linux machine and a Windows machine behind a router that implements NAT (the diagram might be overkill, but was fun to make): I am forwarding RDP port (3389) on the router to the Linux machine because I want to audit RDP connections. For the Linux machine to forward RDP traffic, I wrote these iptables rules: iptables -t nat -A PREROUTING -p tcp --dport 3389 -j DNAT --to-destination win-box iptables -A FORWARD -p tcp --dport 3389 -j ACCEPT The port is listening on the Windows machine: C:\Users\nimmy>netstat -a Active Connections Proto Local Address Foreign Address State (..snip..) TCP 0.0.0.0:3389 WIN-BOX:0 LISTENING (..snip..) And the port is forwarding on the Linux machine: # tcpdump port 3389 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 01:33:11.451663 IP shieldsup.grc.com.56387 > linux-box.myapt.lan.ms-wbt-server: Flags [S], seq 94663035, win 8192, options [mss 1460], length 0 01:33:11.451846 IP shieldsup.grc.com.56387 > win-box.myapt.lan.ms-wbt-server: Flags [S], seq 94663035, win 8192, options [mss 1460], length 0 However, I am not getting any successful RDP connections from the outside. The port is not even responding: C:\Users\outside-nimmy>telnet example.com 3389 Connecting To example.com...Could not open connection to the host, on port 3389: Connect failed Any ideas? Update Per @Zhiqiang Ma, I looked at nf_conntrack proc file during a connection attempt and this is what I see (192.168.3.1 = linux-box, 192.168.3.5 = win-box): # cat /proc/net/nf_conntrack | grep 3389 ipv4 2 tcp 6 118 SYN_SENT src=4.79.142.206 dst=192.168.3.1 sport=43142 dport=3389 packets=6 bytes=264 [UNREPLIED] src=192.168.3.5 dst=4.79.142.206 sport=3389 dport=43142 packets=0 bytes=0 mark=0 secmark=0 zone=0 use=2 2nd update Got tcpdump on the router and it seems that win-box is sending an RST packet: 21:20:24.767792 IP shieldsup.grc.com.45349 > linux-box.myapt.lan.3389: S 19088743:19088743(0) win 8192 <mss 1460> 21:20:24.768038 IP shieldsup.grc.com.45349 > win-box.myapt.lan.3389: S 19088743:19088743(0) win 8192 <mss 1460> 21:20:24.770674 IP win-box.myapt.lan.3389 > shieldsup.grc.com.45349: R 721745706:721745706(0) ack 755785049 win 0 Why would Windows be doing this?

  Read the article

• Aliased network interfaces and isc dhcp server

  - by Jonatan

  I have been banging my head on this for a long time now. There are many discussions on the net about this and similar problems, but none of the solutions seems to work for me. I have a Debian server with two ethernet network interfaces. One of them is connected to internet, while the other is connected to my LAN. The LAN network is 10.11.100.0 (netmask 255.255.255.0). We have some custom hardware that use network 10.4.1.0 (netmask 255.255.255.0) and we can't change that. But we need all hosts on 10.11.100.0 to be able to connect to devices on 10.4.1.0. So I added an alias for the LAN network interface so that the Debian server acts as a gateway between 10.11.100.0 and 10.4.1.0. But then the dhcp server stopped working. The log says: No subnet declaration for eth1:0 (no IPv4 addresses). ** Ignoring requests on eth1:0. If this is not what you want, please write a subnet declaration in your dhcpd.conf file for the network segment to which interface eth1:1 is attached. ** No subnet declaration for eth1:1 (no IPv4 addresses). ** Ignoring requests on eth1:1. If this is not what you want, please write a subnet declaration in your dhcpd.conf file for the network segment to which interface eth1:1 is attached. ** I had another server before, also running Debian but with the older dhcp3 server, and it worked without any problems. I've tried everything I can think of in dhcpd.conf etc, and I've also compared with the working configuration in the old server. The dhcp server need only handle devices on 10.11.100.0. Any hints? Here's all relevant config files: /etc/default/isc-dhcp-server INTERFACES="eth1" /etc/network/interfaces (I've left out eth0, that connects to the Internet, since there is no problem with that.) auto eth1:0 iface eth1:0 inet static address 10.11.100.202 netmask 255.255.255.0 auto eth1:1 iface eth1:1 inet static address 10.4.1.248 netmask 255.255.255.0 /etc/dhcp/dhcpd.conf ddns-update-style none; option domain-name "???.com"; option domain-name-servers ?.?.?.?; default-lease-time 86400; max-lease-time 604800; authorative; subnet 10.11.100.0 netmask 255.255.255.0 { option subnet-mask 255.255.255.0; pool { range 10.11.100.50 10.11.100.99; } option routers 10.11.100.102; } I have tried to add shared-network etc, but didn't manage to get that to work. I get the same error message no matter what...

  Read the article

• Postfix: Relay access denied

  - by Joseph Silvashy

  When I telnet to my server thats running postfix and try to send an email: MAIL FROM:<[email protected]> #=> 250 2.1.0 Ok RCPT TO:<[email protected]> #=> 554 5.7.1 <[email protected]>: Relay access denied I couldn't really find the answer on the site or by looking at other users question/answers, I'm not sure where to start. Ideas? Update So basically looking at the docs: http://www.postfix.org/SMTPD_ACCESS_README.html (section: Getting selective with SMTP access restriction lists), I don't seem to have any of those directives in etc/postfix/main.cf like smtpd_client_restrictions = permit_mynetworks, reject or any of the other ones, so I'm quite confused. But really I'm going to have a rails app connect to the server and send the emails, so I'm not sure how to handle it. Here is what my config file looks like: # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = rerecipe-utils alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = $myhostname, localhost.$mydomain, localhost, mail.rerecipe.com, rerecipe.com relayhost = mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all inet_protocols = all mynetworks = 127.0.0.0/8 204.232.207.0/24 10.177.64.0/19 [::1]/128 [fe80::%eth0]/64 [fe80::%eth1]/64 Something to note is that relayhost is blank, this is the default configuration file that was created when I installed Postfix, when testing to connect with openssl I get this: ~% openssl s_client -connect mail.myhostname.com:25 -starttls smtp CONNECTED(00000003) depth=0 /CN=myhostname verify error:num=18:self signed certificate verify return:1 depth=0 /CN=myhostname verify return:1 --- Certificate chain 0 s:/CN=myhostname i:/CN=myhostname --- Server certificate -----BEGIN CERTIFICATE----- MIIBqTCCARICCQDDxVr+420qvjANBgkqhkiG9w0BAQUFADAZMRcwFQYDVQQDEw5y ZXJlY2lwZS11dGlsczAeFw0xMDEwMTMwNjU1MTVaFw0yMDEwMTAwNjU1MTVaMBkx FzAVBgNVBAMTDnJlcmVjaXBlLXV0aWxzMIGfMA0GCSqGSIb3DQEBAQUAA4GNADCB iQKBgQDODh2w4A1k0qiPNPhkrPj8sfkxpKPTk28AuZhgOEBYBLeHacTKNH0jXxPv P3TyhINijvvdDPzyuPJoTTliR2EHR/nL4DLhr5FzhV+PB4PsIFUER7arx+1sMjz6 5l/Ubu1ppMzW9U0IFNbaPm2AiiGBQRCQN8L0bLUjzVzwoSRMOQIDAQABMA0GCSqG SIb3DQEBBQUAA4GBALi2vvk9TGKJubXYJbU0PKmVmsfzFK35yLqr0keiDBhK2Leg 274sWxEH3ds8mUaRftuFlXb7RYAGNlVyTuMTY3CEcnqIsH7F2McCUTpjMzu/o1mZ O/B21CelKetBd1u79Gkrv2vWyN7Csft6uTx5NIGG2+pGi3r0gX2r0Hbu2K94 -----END CERTIFICATE----- subject=/CN=myhostname issuer=/CN=myhostname --- No client certificate CA names sent --- SSL handshake has read 1203 bytes and written 360 bytes --- New, TLSv1/SSLv3, Cipher is DHE-RSA-AES256-SHA Server public key is 1024 bit Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : DHE-RSA-AES256-SHA Session-ID: 1AA4B8BFAAA85DA9ED4755194C50311670E57C35B8C51F9C2749936DA11918E4 Session-ID-ctx: Master-Key: 9B432F1DE9F3580DCC6208C76F96631DC5A4BC517BDBADD5F514414DCF34AC526C30687B96C5C4742E9583555A118232 Key-Arg : None Start Time: 1292985376 Timeout : 300 (sec) Verify return code: 18 (self signed certificate) --- 250 DSN Oddly enough when I try to send an email from the machine itself it does work: echo test | mail -s "test subject" [email protected]

  Read the article

• The ping response time doesn't reflect the real network response time

  - by yangchenyun

  I encountered a weird problem that the response time returned by ping is almost fixed at 98ms. Either I ping the gateway, or I ping a local host or a internet host. The response time is always around 98ms although the actual delay is obvious. However, the reverse ping (from a local machine to this host) works properly. The following is my route table and the result: route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 100 0 0 eth1 60.194.136.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 # ping the gateway ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_req=1 ttl=64 time=98.7 ms 64 bytes from 192.168.1.1: icmp_req=2 ttl=64 time=97.0 ms 64 bytes from 192.168.1.1: icmp_req=3 ttl=64 time=96.0 ms 64 bytes from 192.168.1.1: icmp_req=4 ttl=64 time=94.9 ms 64 bytes from 192.168.1.1: icmp_req=5 ttl=64 time=94.0 ms ^C --- 192.168.1.1 ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4004ms rtt min/avg/max/mdev = 94.030/96.149/98.744/1.673 ms #ping a local machine ping 192.168.1.88 PING 192.168.1.88 (192.168.1.88) 56(84) bytes of data. 64 bytes from 192.168.1.88: icmp_req=1 ttl=64 time=98.7 ms 64 bytes from 192.168.1.88: icmp_req=2 ttl=64 time=96.9 ms 64 bytes from 192.168.1.88: icmp_req=3 ttl=64 time=96.0 ms 64 bytes from 192.168.1.88: icmp_req=4 ttl=64 time=95.0 ms ^C --- 192.168.1.88 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3003ms rtt min/avg/max/mdev = 95.003/96.696/98.786/1.428 ms #ping a internet host ping google.com PING google.com (74.125.128.139) 56(84) bytes of data. 64 bytes from hg-in-f139.1e100.net (74.125.128.139): icmp_req=1 ttl=42 time=99.8 ms 64 bytes from hg-in-f139.1e100.net (74.125.128.139): icmp_req=2 ttl=42 time=99.9 ms 64 bytes from hg-in-f139.1e100.net (74.125.128.139): icmp_req=3 ttl=42 time=99.9 ms 64 bytes from hg-in-f139.1e100.net (74.125.128.139): icmp_req=4 ttl=42 time=99.9 ms ^C64 bytes from hg-in-f139.1e100.net (74.125.128.139): icmp_req=5 ttl=42 time=99.9 ms --- google.com ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 32799ms rtt min/avg/max/mdev = 99.862/99.925/99.944/0.284 ms I am running iperf to test the bandwidth, the rate is quite low for a LAN connection. iperf -c 192.168.1.87 -t 50 -i 10 -f M ------------------------------------------------------------ Client connecting to 192.168.1.87, TCP port 5001 TCP window size: 0.06 MByte (default) ------------------------------------------------------------ [ 4] local 192.168.1.139 port 54697 connected with 192.168.1.87 port 5001 [ ID] Interval Transfer Bandwidth [ 4] 0.0-10.0 sec 6.12 MBytes 0.61 MBytes/sec [ 4] 10.0-20.0 sec 6.38 MBytes 0.64 MBytes/sec [ 4] 20.0-30.0 sec 6.38 MBytes 0.64 MBytes/sec [ 4] 30.0-40.0 sec 6.25 MBytes 0.62 MBytes/sec [ 4] 40.0-50.0 sec 6.38 MBytes 0.64 MBytes/sec [ 4] 0.0-50.1 sec 31.6 MBytes 0.63 MBytes/sec

  Read the article

• Specifying prerequisites for Puppet custom facts?

  - by larsks

  I have written a custom Puppet fact that requires the biosdevname tool to be installed. I'm not sure how to set things up correctly such that this tool will be installed before facter tries to instantiate the custom fact. Facts are loaded early on in the process, so I can't simply put a package { biosdevname: ensure => installed } in the manifest, since by the time Puppet gets this far the custom fact has already failed. I was curious if I could resolve this through Puppet's run stages. I tried: stage { pre: before => Stage[main] } class { biosdevname: stage => pre } And: class biosdevname { package { biosdevname: ensure => installed } } But this doesn't work...Puppet loads facts before entering the pre stage: info: Loading facts in physical_network_config ./physical_network_config.rb:33: command not found: biosdevname -i eth0 info: Applying configuration version '1320248045' notice: /Stage[pre]/Biosdevname/Package[biosdevname]/ensure: created Etc. Is there any way to make this work? EDIT: I should make it clear that I understand, given a suitable package declaration, that the fact will run correctly on subsequent runs. The difficulty here is that this is part of our initial configuration process. We're running Puppet out of kickstart and want the network configuration to be in place before the first reboot. It sounds like the only workable solution is to simply run Puppet twice during the initial system configuration, which will ensure that the necessary packages are in place. Also, for Zoredache: # This produces a fact called physical_network_config that describes # the number of NICs available on the motherboard, on PCI bus 1, and on # PCI bus 2. The fact value is of the form <x>-<y>-<z>, where <x> # is the number of embedded interfaces, <y> is the number of interfaces # on PCI bus 1, and <z> is the number of interfaces on PCI bus 2. em = 0 pci1 = 0 pci2 = 0 Dir['/sys/class/net/*'].each { |file| devname=File.basename(file) biosname=%x[biosdevname -i #{devname}] case when biosname.match('^pci1') pci1 += 1 when biosname.match('^pci2') pci2 += 1 when biosname.match('^em[0-9]') em += 1 end } Facter.add(:physical_network_config) do setcode do "#{em}-#{pci1}-#{pci2}" end end

  Read the article

• Routing RFC1918 addresses through dd-wrt via a switch

  - by espenfjo

  I am a bit stuck with an experiment of mine. I have a network looking somewhat like this. | Internet | | ---- |Switch| ---- | | Server w/pub IP | DD-WRT router 192.168.1.1 | | RFC1918 clients 192.168.1.0/24 What I want is for the RFC1918 clients to speak directly with each others. On the server with the public IP I have this route: 192.168.1.0/24 dev eth0 scope link and can see that packets are infact reaching the dd-wrt router for 192.168.1.1, even though if I get no answer. Trying to reach one of the RFC1918 clients from the public IP server will get no result, as the dd-wrt router is not announcing that network on to its external interface (arp who-has 192.168.1.107 tell xxx.xxx.xxx.xxx, but no answer). The router being an WLAN dd-wrt router has of course a load of routes, VLANs and interfaces: xxx.xxx.xxx.1 dev vlan2 scope link 192.168.1.0/24 dev br0 proto kernel scope link src 192.168.1.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.244 84.215.64.0/18 dev vlan2 proto kernel scope link src xxx.xxx.xxx.xxx 169.254.0.0/16 dev br0 proto kernel scope link src 169.254.255.1 127.0.0.0/8 dev lo scope link 0.0.0.0 via xxx.xxx.xxx.1 dev vlan2 xxx.xxx.xxx.xxx being the public IP, and xxx.xxx.xxx.1 being the default route for the public IP. I am not sure where to continue with this. I would recon that I both need routing on the dd-wrt router, as well as some iptables magic? Why do something this complex? Why not ;) Also, do not mind that "Internet" can get RFC1918 traffic, it wont go outside of the walls. EDIT 1: Following the tip from stew I do indeed get the correct ARP flowing. And adding an iptables rule for allowing traffic from that specific public IPd machine I get traffic between the systems! Oddly enough though, the speed I get from Server w/pub IP - RFC1918 clients are the same as if the traffic were routed out onto the Internet and back. Edit 2: Ok, disconnecting the external Internet connection will still give the same, crappy transfer speed. So it has to be something else. Edit 3: Ok, I guess there are other reasons for this crappy speed. Case closed. :)

  Read the article

• DELL DRAC & Ubuntu VPN Connection

  - by Mikunos

  I am trying to connect to a DELL DRAC card without success by Ubuntu VPN Connection Manager. I have these data: Protocol: PPTP SERVER IP PPTP: 1233.123.123.123 DRAC IP: 192.168.10.25 Subnet: 255.255.0.0 User: myuser Pass: mypass where have I to write these parameters? I have configured the PPTP connection using the graphical tool in Ubuntu 11.10 ... but in the /var/log/syslog I get these messages: Apr 15 11:33:15 shinet NetworkManager[1035]: <info> Starting VPN service 'pptp'... Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' started (org.freedesktop.NetworkManager.pptp), PID 18180 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' appeared; activating connections Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN plugin state changed: 3 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN connection 'Connessione VPN 1' (Connect) reply received. Apr 15 11:33:15 shinet pppd[18182]: Plugin /usr/lib/pppd/2.4.5/nm-pptp-pppd-plugin.so loaded. Apr 15 11:33:15 shinet pppd[18182]: pppd 2.4.5 started by root, uid 0 Apr 15 11:33:15 shinet pppd[18182]: Using interface ppp0 Apr 15 11:33:15 shinet pppd[18182]: Connect: ppp0 <--> /dev/pts/1 Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp0, iface: ppp0): no ifupdown configuration found. Apr 15 11:33:15 shinet pptp[18185]: nm-pptp-service-18180 log[main:pptp.c:314]: The synchronous pptp option is NOT activated Apr 15 11:33:46 shinet pppd[18182]: LCP: timeout sending Config-Requests Apr 15 11:33:46 shinet pppd[18182]: Connection terminated. Apr 15 11:33:46 shinet avahi-daemon[1081]: Withdrawing workstation service for ppp0. Apr 15 11:33:46 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:46 shinet pppd[18182]: Modem hangup Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet pppd[18182]: Exit. Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state changed: 6 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state change reason: 0 Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> error disconnecting VPN: Could not process the request because no VPN connection was active. Apr 15 11:33:51 shinet NetworkManager[1035]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Apr 15 11:33:57 shinet NetworkManager[1035]: <info> VPN service 'pptp' disappeared Thanks

  Read the article

• SSH to an ubuntu machine using avahi

  - by tensaiji

  I have an ubuntu box that I connect to using avahi. Connecting to that box works fine for all services (I regularly use AFP, SSH and SMB on it) but I've noticed that whenever I connect to it from a mac using SSH (and using the ".local" dns name provided by avahi - eg. "ssh .local") SSH tries to connect using ipv6, which for some reason times out (after two minutes) then it tries ipv4 which connects immediately. I'd like to avoid this timeout, as it's really annoying for me and other users - if SSH tried ipv4 first or if ssh over ipv6 worked then that would solve the problem. But so far I've been unable to get either to work (the best I've managed is to specify the "-4" option to SSH to stop it from trying ipv6 at all). I'm using Ubuntu 10.04. Any solution has to be on the server (not the client) as there are multiple clients connecting. A possible complication might be that my LAN is set up to allow link-local ipv6 addresses only, but I have other servers (using Mac OS) that I can SSH into using ipv6) I suspect that the problem could be solved by either preventing avahi from broadcasting the ipv6 address, or by enabling ssh over ipv6, but so far as I can tell avahi is already configured not to broadcast the ipv6 address and sshd is configured to allow ipv6 connections! Here's my /etc/avahi/avahi-daemon.conf (I don't think I've changed anything from the ubuntu defaults) [server] #host-name=foo #domain-name=local #browse-domains=0pointer.de, zeroconf.org use-ipv4=yes use-ipv6=no #allow-interfaces=eth0 #deny-interfaces=eth1 #check-response-ttl=no #use-iff-running=no #enable-dbus=yes #disallow-other-stacks=no #allow-point-to-point=no [wide-area] enable-wide-area=yes [publish] #disable-publishing=no #disable-user-service-publishing=no #add-service-cookie=no #publish-addresses=yes #publish-hinfo=yes #publish-workstation=yes #publish-domain=yes #publish-dns-servers=192.168.50.1, 192.168.50.2 #publish-resolv-conf-dns-servers=yes #publish-aaaa-on-ipv4=yes #publish-a-on-ipv6=no [reflector] #enable-reflector=no #reflect-ipv=no [rlimits] #rlimit-as= rlimit-core=0 rlimit-data=4194304 rlimit-fsize=0 rlimit-nofile=300 rlimit-stack=4194304 rlimit-nproc=3 and here's my sshd_config (mainly updated to only allow pub/private keys): # What ports, IPs and protocols we listen for Port 22 # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH LogLevel INFO # Authentication: LoginGraceTime 180 PermitRootLogin no StrictModes yes RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords PasswordAuthentication no AllowGroups sshusers # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding yes X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no MaxStartups 10:30:60 #Banner /etc/issue.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server UsePAM yes Does anyone have any ideas that I can try, or has experienced anything similar?

  Read the article

• How can I force all internet traffic over a PPTP VPN but still allow local lan access?

  - by user126715

  I have a server running Linux Mint 12 that I want to keep connected to a PPTP VPN all the time. The VPN server is pretty reliable, but it drops on occasion so I just want to make it so all internet activity is disabled if the VPN connection is broken. I'd also like to figure out a way to restart it automatically, but that's not as big of an issue since this happens pretty rarely. I also want to always be able to connect to the box from my lan, regardless of whether the VPN is up or not. Here's what my ifconfig looks like with the VPN connected properly: eth0 Link encap:Ethernet HWaddr 00:22:15:21:59:9a inet addr:192.168.0.171 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::222:15ff:fe21:599a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:37389 errors:0 dropped:0 overruns:0 frame:0 TX packets:29028 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:37781384 (37.7 MB) TX bytes:19281394 (19.2 MB) Interrupt:41 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1446 errors:0 dropped:0 overruns:0 frame:0 TX packets:1446 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:472178 (472.1 KB) TX bytes:472178 (472.1 KB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.10.11.10 P-t-P:10.10.11.9 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:23 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:1368 (1.3 KB) TX bytes:1812 (1.8 KB) Here's an iptables script I found elsewhere that seemed to be for the problem I'm trying to solve, but it wound up blocking all access, but I'm not sure what I need to change: #!/bin/bash #Set variables IPT=/sbin/iptables VPN=`ifconfig|perl -nE'/dr:(\S+)/&&say$1'|grep 10.` LAN=192.168.0.0/24 #Flush rules $IPT -F $IPT -X #Default policies and define chains $IPT -P OUTPUT DROP $IPT -P INPUT DROP $IPT -P FORWARD DROP #Allow input from LAN and tun0 ONLY $IPT -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT $IPT -A INPUT -i lo -j ACCEPT $IPT -A INPUT -i tun0 -m conntrack --ctstate NEW -j ACCEPT $IPT -A INPUT -s $LAN -m conntrack --ctstate NEW -j ACCEPT $IPT -A INPUT -j DROP #Allow output from lo and tun0 ONLY $IPT -A OUTPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT $IPT -A OUTPUT -o lo -j ACCEPT $IPT -A OUTPUT -o tun0 -m conntrack --ctstate NEW -j ACCEPT $IPT -A OUTPUT -d $VPN -m conntrack --ctstate NEW -j ACCEPT $IPT -A OUTPUT -j DROP exit 0 Thanks for your help.

  Read the article

• Linksys WiFi usb dongle and linux woes

  - by MrStatic

  I have a Linksys WUSB54GC usb dongle and I have exhausted every thing I know about making this thing work in linux. I am using Fedora 13. Since it is not ready I can not view any networks. Any ideas would be great. tail of the system log Jun 2 20:14:35 localhost kernel: usb 1-7: new high speed USB device using ehci_hcd and address 8 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device found, idVendor=1737, idProduct=0077 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jun 2 20:14:35 localhost kernel: usb 1-7: Product: 802.11 g WLAN Jun 2 20:14:35 localhost kernel: usb 1-7: Manufacturer: Ralink Jun 2 20:14:35 localhost kernel: usb 1-7: SerialNumber: 1.0 Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::radio Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::assoc Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::quality Jun 2 20:14:35 localhost NetworkManager[1367]: <info> found WiFi radio killswitch rfkill3 (at /sys/devices/pci0000:00/0000:00:1d.7/usb1/1-7/1-7:1.0/ieee80211/phy3/rfkill3) (driver <unknown>) Jun 2 20:14:35 localhost kernel: rt2800usb 1-7:1.0: firmware: requesting rt2870.bin Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2800usb' ifindex: 6) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/4 Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): now managed Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 1 -> 2 (reason 2) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): bringing up device. Jun 2 20:14:35 localhost kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): preparing device. Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): deactivating device (reason: 2). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): supplicant interface state: starting -> ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 2 -> 3 (reason 42) [root@localhost log]# iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg Mode:Managed Access Point: Not-Associated Tx-Power=8 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on

  Read the article

• OpenVPN bridged not pinging beyond openvpn server on Ubuntu/Windows 2003

  - by ani

  I set up an OpenVPN server using Ubuntu and a windows server 2003 client to interconnect two networks between two different offices. They can now ping each other, but the rest of the network cannot be contacted by the windows client. Office 1 has internal network of: 192.168.0.0 255.255.240.0 Office 2 has internal network of: 192.168.16.0 255.255.255.0 And the configuration files are: Server.conf port 1194 --script-security 2 up "/etc/openvpn/up.sh br0" down "/etc/openvpn/down.sh br0" # TCP or UDP server? ;proto tcp proto udp dev tap0 ;dev tun ca ca.crt cert openvpn.crt key openvpn.key dh dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 192.168.0.59 255.255.240.0 192.168.6.72 192.168.6.75 push "route 192.168.0.0 255.255.240.0" push "dhcp-option DNS 192.168.0.2" push "dhcp-option DOMAIN testeers.local" keepalive 10 120 tls-auth ta.key 0 # This file is secret comp-lzo user nobody group nogroup persist-key persist-tun log /var/log/openvpn/openvpn.log status /var/log/openvpn-status.log verb 3 Client Config file client dev tap ;dev tun --script-security 2 ;proto tcp proto udp remote 1xx.2xx.xxx.124 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert admin-VAIO.crt key admin-VAIO.key ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 Ifconfig on the server now shows the following: br0 Link encap:Ethernet HWaddr 00:50:56:8b:1a:49 inet addr:192.168.0.59 Bcast:192.168.15.255 Mask:255.255.240.0 inet6 addr: fe80::250:56ff:fe8b:1a49/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1081860 errors:0 dropped:1358 overruns:0 frame:0 TX packets:242385 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76600615 (76.6 MB) TX bytes:64474575 (64.4 MB) eth0 Link encap:Ethernet HWaddr 00:50:56:8b:1a:49 UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:1144125 errors:0 dropped:7172 overruns:0 frame:0 TX packets:252486 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:109893729 (109.8 MB) TX bytes:66372620 (66.3 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:67865 errors:0 dropped:0 overruns:0 frame:0 TX packets:67865 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5183276 (5.1 MB) TX bytes:5183276 (5.1 MB) tap0 Link encap:Ethernet HWaddr 32:4f:42:11:b7:c5 inet6 addr: fe80::304f:42ff:fe11:b7c5/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:3329 errors:0 dropped:0 overruns:0 frame:0 TX packets:215472 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:373205 (373.2 KB) TX bytes:17465832 (17.4 MB)

  Read the article

• Transient network dropout for Xen DomU's

  - by Stephen C

  We've got a CentOS server running a cluster of virtuals. Occasionally the cluster's internal network drops out for a minute or so ... and then comes back. The problem is somehow related to the actual network traffic, but it is not a simple load issue. (The system is generally lightly loaded, and the problem occurs irrespective of actual load.) The setup: CentOS 5.6 on Dom0, various CentOS on the DomU's Hardware - a Dell R710 with a BroadCom NextXpress 2 NIC (sigh) using the latest drivers for the NIC from BroadCom Xen configured to use network-bridge and vif-bridge Some iptable tweaks to route an unrelated port to one of the virtuals. The system has one externally visible IP address, and Dom0 runs an Apache httpd configured with a number of virtual hosts each of which reverse proxies to web servers running on the virtuals. (The virtuals have to be NAT'ed, primarily because we don't have enough allocated public IP addresses.) The symptoms: Works fine most of the time. When someone tries to UPLOAD a large file to one virtuals, the internal network drops out ... for all virtuals: The Dom0 httpd sees a network timeout talking to the backend server on the virtual and reports a 502. A previously established ssh connection from Dom0 to any of the DomU's freezes. Our monitoring shows ping failures for traffic between virtuals. The Xen consoles to the DomU's do not freeze. No log messages in any log files that I can see, on either Dom0 or the DomU's ... apart from the Dom0 httpd logs. After a minute or so, the problem clears by itself. This is 100% reproducible. What we've tried: Downloading, building and installing the latest BNX2 driver on Dom0 Turning off MSI on the NIC - adding "options bnx2 disable_msi=1" to /etc/modprobe.conf Turning off tcp segmentation offload - "ethtool -K eth0 tso off". Sacrificing a black rooster at midnight. I've exhausted all my options apart from switching to KVM ... or slaughtering more roosters. Any suggestions?

  Read the article

• Suspected network performance issue on VirtualBox Ubuntu guest on Win7 host

  - by Adam

  I set up Ubuntu 12.04 in VirtualBox on the Win7 machine I was allocated on my new project. I am running Java, Eclipse, Tomcat to develop a large data-intensive application and I noticed that this application runs at half the speed of my colleague's identical machine, where he runs it all under Windows. I think I have narrowed down the performance issue to the network, after comparing and equalising all the Java VM settings with my colleague. Is there a ping test I can do or some other network diagnostic test to flag up any problems? To give some background, the network performance is confusing. Running a network speed test to my colleague's machine with iperf shows speeds of 6 Mb/s from my Ubuntu guest, and 90 Mb/s from the win7 host. Large downloads, e.g. the Java SDK, come down at about 1.2 MB/s on both the guest and the host. Pings are sub-1ms on the host, but 1.5ms on the guest. I also did a broadband speed test, and got 10Mb/s download speed on both, but the host has an upload speed of 10Mb/s but the guest only uploads at 3Mb/s. I've been trying to diagnose any MTU problems with ping -M do to identify any kind of packet fragmentation problem but it's progressing very slow because I don't have much experience in this area. From what I read on other people's networking issues with VB and Linux guests on Win7 hosts, I should be able to get the speed on the guest up to the same level as the host. I installed a fresh VM with Ubuntu again to see if I'd foobar'd it somehow, but I'm getting the same readings with iperf on the virgin installation. My setup is: Adapter 1: Intel PRO/1000 MT Desktop (NAT) Adapter 2: ditto (host-only adapter) eth0 Link encap:Ethernet HWaddr 08:00:27:0b:76:bf inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe0b:76bf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:86236 errors:0 dropped:0 overruns:0 frame:0 TX packets:49369 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:69163946 (69.1 MB) TX bytes:3530535 (3.5 MB) eth2 Link encap:Ethernet HWaddr 08:00:27:a3:26:b8 inet addr:192.168.56.101 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fea3:26b8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:59 errors:0 dropped:0 overruns:0 frame:0 TX packets:57 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9148 (9.1 KB) TX bytes:7648 (7.6 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:701 errors:0 dropped:0 overruns:0 frame:0 TX packets:701 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:66321 (66.3 KB) TX bytes:66321 (66.3 KB)

  Read the article

• Ubuntu hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  I'm posting this on SU after it stalled on askubuntu. I hope someone here can help! If you'd prefer to answer on AU itself, here's the link: http://askubuntu.com/questions/365177/hardware-wireless-switch-has-no-effect-after-suspend-and-13-10-upgrade Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Edit. This morning, I had had the laptop suspended all night, and then when I tried to awake it, it simply wouldn't. It would try, and then it would sleep again (I guess it felt a little bit like me! </badjoke>). Is it possible these problems are related? Edit. I don't have enough reputation on SU proper to post links to pastebins and other questions I've tried, so I'm putting them in comments, and of course they're available in the original question.

  Read the article

• Wirelss card not being detected in backtrack 5

  - by Jesse Nelson

  I just installed backtrack 5 and I am unable to detect my wireless card. iwconfig doesn't list my interface. I can see that the hardware is present in lspci -vnn (see below) but I can't get the interface detected. I have tried to reinstall the compat-wireless package but I get errors during the build (see below) I have done a ton of researching and I keep hitting a brick wall, mostly because the wiki for backtrack is down and I can't find any good resources. Does anyone know how to fix the issue? Also, does anyone no how I can scan the hardware to determine what NIC is assigning my interface? If I can figure out the interface name I think I can set it up manually by putting up the link and using wireless-tools to manually configure the connection, this is what I had to do in arch on my mac. As stated the wiki for backtrack is down and I can't find any help on the issue. I tried to do the full kernel upgrade suggested in my software update but after the update was complete and I logged back in I had a new log in manager and the only thing I was able to log into was window managers. However, after this update my wireless was working fine. Please help I am new to Linux and the wiki is down, I have nowhere else to turn. Forgot to mention I am using the KDE version, not Gnome. Thanks in advance for any help or support. Attempt at make: root@bt:/usr/src/compat-wireless-3.3-rc1-2# make /usr/src/compat-wireless-3.3-rc1-2/config.mk:254: "WARNING: CONFIG_CFG80211_WEXT will be deactivated or not working because kernel was compiled with CONFIG_WIRELESS_EXT=n. Tools using wext interface like iwconfig will not work. To activate it build your kernel e.g. with CONFIG_LIBIPW=m." make -C /lib/modules/2.6.38/build M=/usr/src/compat-wireless-3.3-rc1-2 modules make: *** /lib/modules/2.6.38/build: No such file or directory. Stop. make: *** [modules] Error 2 lspci output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn -i net lspci: I/O error at net, line 0 root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn 02:00.0 Network controller [0280]: Atheros Communications Inc. Device [168c:0032] (rev ff) (prog-if ff) !!! Unknown header type 7f ( This is the problem but I can't find the solution) Kernel modules: ath9k iwconfig output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• how to setup kismet.conf on Ubuntu

  - by Registered User

  I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

  Read the article

• tc rules block traffic from some hosts at network

  - by user139430

  I have a problem I can not solve. The script, which sets the rules for traffic shaping is blocking the traffic from some hosts.If I remove all the rules, then it works. I can not understand why? Here is my script... #!/bin/sh cmdTC=/sbin/tc rateLANDl="60mbit" ceilLANDl="60mbit" rateLANUl="40mbit" ceilLANUl="40mbit" quantLAN="1514" # Nowaday bandwidth limit set to 100mbit. # We devide it with 60mbit download and 40mbit upload bandthes. rateHiDl="30mbit" ceilHiDl="60mbit" rateHiUl="20mbit" ceilHiUl="40mbit" quantHi="1514" rateLoDl="30mbit" ceilLoDl="60mbit" rateLoUl="20mbit" ceilLoUl="40mbit" quantLo="1514" devNIF=eth0 devFIF=ifb0 modprobe ifb ip link set $devFIF up 2>/dev/null #exit 0 ################################################################################################ # Remove discuiplines from network and fake interfaces ################################################################################################ $cmdTC qdisc del dev $devNIF root 2>/dev/null $cmdTC qdisc del dev $devFIF root 2>/dev/null $cmdTC qdisc del dev $devNIF ingress 2>/dev/null if [ "$1" = "down" ]; then exit 0 fi ################################################################################################ # Create discuiplines for network interface ################################################################################################ $cmdTC qdisc add dev $devNIF root handle 1:0 htb default 12 # Create classes for network interface $cmdTC class add dev $devNIF parent 1:0 classid 1:1 htb rate ${rateLANDl} ceil ${ceilLANDl} quantum ${quantLAN} $cmdTC class add dev $devNIF parent 1:1 classid 1:11 htb rate ${rateHiDl} ceil ${ceilHiDl} quantum ${quantHi} $cmdTC class add dev $devNIF parent 1:1 classid 1:12 htb rate ${rateLoDl} ceil ${ceilLoDl} quantum ${quantLo} $cmdTC qdisc add dev $devNIF parent 1:11 handle 111: sfq perturb 10 $cmdTC qdisc add dev $devNIF parent 1:12 handle 112: sfq perturb 10 # Create filters for network interface $cmdTC filter add dev $devNIF protocol all parent 1:0 u32 match ip dst 10.252.2.0/24 flowid 1:11 $cmdTC filter add dev $devNIF protocol all parent 111: handle 111 flow hash keys dst divisor 1024 baseclass 1:11 $cmdTC filter add dev $devNIF protocol all parent 112: handle 112 flow hash keys dst divisor 1024 baseclass 1:12 ################################################################################################ # Create discuiplines for fake interface ################################################################################################ $cmdTC qdisc add dev $devFIF root handle 1:0 htb default 12 # Create classes for network interface $cmdTC class add dev $devFIF parent 1:0 classid 1:1 htb rate ${rateLANUl} ceil ${ceilLANUl} quantum ${quantLAN} $cmdTC class add dev $devFIF parent 1:1 classid 1:11 htb rate ${rateHiUl} ceil ${ceilHiUl} quantum ${quantHi} $cmdTC class add dev $devFIF parent 1:1 classid 1:12 htb rate ${rateLoUl} ceil ${ceilLoUl} quantum ${quantLo} $cmdTC qdisc add dev $devFIF parent 1:11 handle 111: sfq perturb 10 $cmdTC qdisc add dev $devFIF parent 1:12 handle 112: sfq perturb 10 # Create filters for network interface $cmdTC filter add dev $devFIF protocol all parent 1:0 u32 match ip src 10.252.2.0/24 flowid 1:11 $cmdTC filter add dev $devFIF protocol all parent 111: handle 111 flow hash keys src divisor 1024 baseclass 1:11 $cmdTC filter add dev $devFIF protocol all parent 112: handle 112 flow hash keys src divisor 1024 baseclass 1:12 ################################################################################################ # Create redirect discuiplines from network to fake interface ################################################################################################ $cmdTC qdisc add dev $devNIF handle ffff:0 ingress $cmdTC filter add dev $devNIF parent ffff:0 protocol all u32 match u32 0 0 action mirred egress redirect dev $devFIF Here is my /etc/modules: loop ifb ppp_mppe nf_conntrack_pptp nt_conntrack_proto_gre nf_nat_pptp nf_nat_proto_gre The system is Linux wall 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux

  Read the article

< Previous Page | 51 52 53 54 55 56 57 58 59  | Next Page >