Search Results

Search found 28563 results on 1143 pages for 'strange but true'.

Page 561/1143 | < Previous Page | 557 558 559 560 561 562 563 564 565 566 567 568  | Next Page >

• High CPU load for 1:30 minutes when mounting ext4-raid partition

  - by sirion

  I have a raid 5 (software) with 5x2TB drives. I encrypted the raid with cryptsetup and put an ext4-partition on top. In the beginning opening and mounting the raid took less than 10 seconds, now (for a few weeks) mounting alone takes 1:30 minutes and the cpu stays around 93% the whole time: The output of "time sudo mount /dev/mapper/8000 /media/8000" is: real 1m31.952s user 0m0.008s sys 1m25.229s At the same time only one line is added to /var/log/syslog: kernel: [ 2240.921381] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null) My Ubuntu-version is "12.04.1 LTS" and no updates are pending. I checked the partition with fsck, but it says that all is ok. The "cryptsetup luksOpen" command only takes a few seconds. I also tried changing the raid-bitmap (as it was suggested in some forum) but it did not change the behaviour. sudo mdadm --grow /dev/md0 -b internal and sudo mdadm --grow /dev/md0 -b none I had the idea that it might be the hardware being slow, but a read test with "sudo hdparm -t /dev/md0" spit out values between 62 and 159 MB/sec: Timing buffered disk reads: 382 MB in 3.00 seconds = 127.14 MB/sec Timing buffered disk reads: 482 MB in 3.02 seconds = 159.62 MB/sec Timing buffered disk reads: 190 MB in 3.03 seconds = 62.65 MB/sec Timing buffered disk reads: 474 MB in 3.02 seconds = 157.12 MB/sec Although I think it is strange that the read rate jumps by more than 100% - could that mean something? The speed test when reading from the mapped (decrypted) device shows similar behavior, although it is of course much slower. "sudo hdparm -t /dev/mapper/8000": Timing buffered disk reads: 56 MB in 3.02 seconds = 18.54 MB/sec Timing buffered disk reads: 122 MB in 3.09 seconds = 39.43 MB/sec Timing buffered disk reads: 134 MB in 3.02 seconds = 44.35 MB/sec The output of a verbose mount "mount -vvv /dev/mapper/8000 /media/8000" does not help much: mount: fstab path: "/etc/fstab" mount: mtab path: "/etc/mtab" mount: lock path: "/etc/mtab~" mount: temp path: "/etc/mtab.tmp" mount: UID: 0 mount: eUID: 0 mount: spec: "/dev/mapper/8000" mount: node: "/media/8000" mount: types: "(null)" mount: opts: "(null)" mount: you didn't specify a filesystem type for /dev/mapper/8000 I will try type ext4 mount: mount(2) syscall: source: "/dev/mapper/8000", target: "/media/8000", filesystemtype: "ext4", mountflags: -1058209792, data: (null) Any idea where I could find additional information on why mounting takes so long, or what additional tests I could run?

  Read the article

• Homepage issue on Google [closed]

  - by nico

  We have recently updated our website www.blinds4uk.co.uk with a new homepage containing additional features and more on page content but since then we have lost primary keyword positions and the home page has disappeared completely. The only time it appears is for an exact search ‘blinds4uk’. Today I took snippets of 'unique content' from the homepage and put this into the 'google search' but our homepage was nowhere to be found. When I did the same in ‘Yahoo’ the homepage came up. Are we missing something? We ranked in the top 4 for primary kw terms 'blinds uk' & 'uk blinds' but now we don’t show anywhere for these terms. Our homepage has never ranked well for the primary kw 'blinds' yet our internal pages rank very well with many pages on page 1 of google uk. We employed an SEO firm for 9 months to help us establish issues with the homepage but they never could, so we got rid. We have been trying to get to the root cause of why the homepage ranks so poorly for a number of years and only yesterday we established that we had the meta tag directly below the tag and our title & meta description were further down the page; we have today corrected. Not sure what effect this would have on the way Google reads the homepage but we are trying everything to try and get the homepage ranking fro those primary kw's. Our current developers & ex SEO guys are all part of the same company and cannot pin-point anything other than saying carryon with their SEO team because it will take time but just comes across as a milking exercise. Another thing which I have found very strange is the data from our 'traffic audience'. We are a UK based website yet our traffic stats were showing as;- UK 36.6%, Denmark 35.8% and India 27.6%. – don’t make sense to me! Is there anybody out there that could simply point us in the right direction to the problem(s), so we can fix once and for all? Could there be anything within the code that is causing the home page not to display within google for our primary kw's terms such as blinds, window blinds etc. I would appreciate any advice at all that may help us in our quest to sort this homepage issue once and for all

  Read the article

• Movement prediction for non-shooters

  - by ShadowChaser

  I'm working on an isometric (2D) game with moderate-scale multiplayer - 20-30 players. I've had some difficulty getting a good movement prediction implementation in place. Right now, clients are authoritative for their own position. The server performs validation and broad-scale cheat detection, and I fully realize that the system will never be fully robust against cheating. However, the performance and implementation tradeoffs work well for me right now. Given that I'm dealing with sprite graphics, the game has 8 defined directions rather than free movement. Whenever the player changes their direction or speed (walk, run, stop), a "true" 3D velocity is set on the entity and a packet it sent to the server with the new movement state. In addition, every 250ms additional packets are transmitted with the player's current position for state updates on the server as well as for client prediction. After the server validates the packet, it gets automatically distributed to all of the other "nearby" players. Client-side, all entities with non-zero velocity (ie/ moving entities) are tracked and updated by a rudimentary "physics" system - basically nothing more than changing the position by the velocity according to the elapsed time slice (40ms or so). What I'm struggling with is how to implement clean movement prediction. I have the nagging suspicion that I've made a design mistake somewhere. I've been over the Unreal, Half-life, and all other movement prediction/lag compensation articles I could find, but they all seam geared toward shooters: "Don't send each control change, send updates every 120ms, server is authoritative, client predicts, etc". Unfortunately, that style of design won't work well for me - there's no 3D environment so each individual state change is important. 1) Most of the samples I saw tightly couple movement prediction right into the entities themselves. For example, storing the previous state along with the current state. I'd like to avoid that and keep entities with their "current state" only. Is there a better way to handle this? 2) What should happen when the player stops? I can't interpolate to the correct position, since they might need to walk backwards or another strange direction if their position is too far ahead. 3) What should happen when entities collide? If the current player collides with something, the answer is simple - just stop the player from moving. But what happens if two entities take up the same space on the server? What if the local prediction causes a remote entity to collide with the player or another entity - do I stop them as well? If the prediction had the misfortune of sticking them in front of a wall that the player has gone around, the prediction will never be able to compensate and once the error gets to high the entity will snap to the new position.

  Read the article

• If most of team can't follow the architecture, what do you do?

  - by Chris

  Hi all, I'm working on a greenfields project with two other developers. We're all contractors, and myself and one other just started working on the project while the orginal one has been doing most of the basic framework coding. In the past month, my fellow programmer and I have been just frustrated by the design descisions done by our co-worker. Here's a little background information: The application at face value appeared to be your standard n-layered web application using C# on the 3.5 framework. We have a data layer, business layer and a web interface. But as we got deeper into the project we found some very interesting things that have caused us some troubles. There is a custom data access sqlHelper type base which only accepts dictionary key/valued entries and returns only data tables. There are no entity objects, but there are some massive objects which do everything and then are tossed into session for persitance. The general idea is that the pages (.aspx) don't do anything, while the controls (.ascx) do everything. The general flow is that a client clicks on a button, which goes to a user control base which passes a process request to the 'BLL' class which goes to the page processor, which then goes to a getControlProcessor, which at last actually processes the request. The request itself is made up of a dictionary which is passing a string valued method name, stored procedure name, a control name and possibly a value. All switching of the processing is done by comparing the string values of the control names and method names. Pages are linked together via a common header control that uses a combination of javascript and tables to create a hyperlink effect. And as I found out yesterday, a simple hyperlink between one page and another does not work because of the need to have quite a bit of information in session to determine which control to display on a page. My fellow programmer and I both believe that this is a strange and uncommon approach to web application development. Both of us have been in this business for over five years and neither of us have seen this approach. My question is this, how would we approach our co-worker and voice our concerns and what should we do if he does not want to accept the criteic? We both do not want to insult the work that has been done, but feel that going forward will create a nightmare for development. Thanks for your comments.

  Read the article

• Remote Graphics Diagnostics with Windows RT 8.1 and Visual Studio 2013

  - by Michael B. McLaughlin

  Originally posted on: http://geekswithblogs.net/mikebmcl/archive/2013/11/12/remote-graphics-diagnostics-with-windows-rt-8.1-and-visual-studio.aspxThis blog post is a brief follow up to my What’s New in Graphics and Game Development in Visual Studio 2013 post on the MVP Award blog. While writing that post I was testing out various features to try to make sure everything worked as expected. I had some trouble getting Remote Graphics Diagnostics (a/k/a remote graphics debugging) working on my first generation Surface RT (upgraded to Windows RT 8.1). It was more strange since I could use remote debugging when doing CPU debugging; it was just graphics debugging that was causing trouble. After some discussions with the great folks who work on the graphics tools in Visual Studio, they were able to repro the problem and recommend a solution. My Surface RT needed the ARM Kits policy installed on it. Once I followed the instructions on the previous link, I could successfully use Remote Graphics Diagnostics on my Surface RT. Please note that this requires Windows RT 8.1 RTM (i.e. not Preview) and that Remote Graphics Diagnostics on ARM only works when you are using Visual Studio 2013 as it is a new feature (it should work just fine using the Express for Windows version). Also, when I installed the ARM Kits policy I needed to do two things to get it to work properly. First, when following the “How to install the Kits policy” instructions, I needed to copy the SecureBoot folder into Program Files on my Surface RT (specifically, I copied the SecureBoot folder to “C:\Program Files\Windows Kits\8.1\bin\arm\” on my Surface RT, creating any necessary directories). It may work if it’s in any system folder; I didn’t test any others after I got it working. I had initially put it in my Downloads folder and tried installing it from there. When the machine restarted it displayed a worrisome error message. I repeatedly pressed the button that would allow me to retry and eventually the machine rebooted and managed to recover itself to its previous state. Second, I needed to install it as an Administrator. The instructions say that this might be necessary. For me it was. This is a Remote Graphics Diagnostics is a great new feature in Visual Studio 2013 so I definitely encourage all of you to check it out!

  Read the article

• Is multiple domain names and links from same IP causing poor search engine rankings?

  - by John

  I have an ecommerce website which is not doing so well in Google. I am trying to improve this of course, and am looking at some possibilities for why it isn't doing well. The website has four domain names, all of which have been indexed by Google. A few months ago I applied 301 redirects to any requests for two of the domain names so now it is down to two domain names (one is a .net, the other is a .com.au, the others were .net.au and .com). I prefer to use my main domain name (the .com.au), but one of the names has been around for a long time and has more inbound links. According to a PageRank tool, both are PR2. It is a Classic ASP site and up until recently had a lot of querystring parameters. In the last week or so I added URL rewriting so there is now no parameters for most pages. I don't do 301 redirects from the old URLs but instead I add the META canonical tag indicating the preferred new URL. At the same time I redesigned the site and improved title tags, META descriptions, and H tags but it hasn't been long enough yet for Google to index many of these yet. I also looked at what pages Google has indexed and strangely it has some strange pages in the index, there are a lot of pages which are actual keyword searches (more a bunch of random letters than an actual word). What I mean is that it is as if they had typed in something to search for in my search box - there are no links to pages like this and the only way of getting this is to type something in to the search box). So I added a META robots tag with noindex,nofollow anytime that I render pages like this. Years ago I set up a fake price comparison site which lists all my products and links back to my site. It has a different keyword rich domain name but is on the same server and same IP address. It's a completely different layout but does have the same product categories and product descriptions (although I have stripped formatting out of them so they are not identical except in text). I also have a few blog sites which again are on the same server/IP and all have advertising for the website. My questions are: What should I do with the multiple domains, just use one, or continue with two or more? Should I add 301 redirects, not just the META canonical tag? Any idea about Google indexing my search results page, and did I do the right thing with the META robots tag? Is the fake price comparison site likely to be causing problems? Are all the links to the site from other domain names but the same IP address likely to be causing problems? Thanks for any help. Sorry for so many questions in one.

  Read the article

• How bad does it look to have left a job soon after starting? [closed]

  - by unitedgremlin

  I have a job I would like to leave. On advice from friends and parents I have stayed. Their primary concern is that it would look bad on my resume if I left only after a few months of joining. My concerns with the job are as follows: When I started it was preferred I provide and use my own equipment. Could be out of business in a few months from lack of cash flow Poor code quality: memory leaks and lack of error handling. The same mistakes continue to be made even though I have raised the issue. It has become evident that co-workers do not understand memory management rules of the platform and are not interested in learning them. Yet, there is still surprise from them when strange bugs continue to crop up. As a result don't feel I will learn from co-workers. Plus, fixing the the lingering bugs and trying to keep up on new feature development is like a game of whack-o-mole that never ends. I don't believe in the companies vision or its ability to execute on the ideas anymore. My ideas and suggestions for very small tweaks are quickly dismissed. And so more than half or so have come back as bugs that we end up needing to address. I have been told to wait on fixing bugs in codes until we can talk to the original author. I don't feel I am allowed to take initiative to just fix/change things and do what I think is best. Everything needs consensus even for a bug fix before any work is done. I am adopting a shut-up and just do what I am told approach to save myself from ulcers. Lots of meetings (I am personally not involved in all of them which is good) but the sheer amount reminds me of days at a big corporation. Why is everyone around me always meeting? It's a small company. I can count everyone on my toes and fingers. I can say with certainty I have no interest in working with any of them again. This is the first time I have truly worked with a group of so called "B and C players". Ultimately, I think it is my fault for not doing a better job evaluating the team and company before joining. But I have generated a better set of questions when probing companies in the future. My questions are: How bad does it look to have left a job soon (few months) after starting? What would be the best way to explain my concerns and reasons for leaving without badmouthing the company? Should I stick it out to what I believe will be the soon end of the company?

  Read the article

• iOS app with a lot of text

  - by rdurand

  I just asked a question on StackOverflow, but I'm thinking that a part of it belongs here, as questions about design pattern are welcomed by the faq. Here is my situation. I have developed almost completely a native iOS app. The last section I need to implement is all the rules of a sport, so that's a lot of text. It has one main level of sections, divided in subsections, containing a lot of structured text (paragraphs, a few pictures, bulleted/numbered lists, tables). I have absolutely no problem with coding, I'm just looking for advice to improve and make the best design pattern possible for my app. My first shot (the last one so far) was a UITableViewController containing the sections, sending the user to another UITableViewController with the subsections of the selected section, and then one strange last UITableViewController where the cells contain UITextViews, sections header help structure the content, etc. What I would like is your advice on how to improve the structure of this section. I'm perfectly ready to destroy/rebuild the whole thing, I'm really lost in my design here.. As I said on SO, I've began to implement a UIWebView in a UIViewController, showing a html page with JQuery Mobile to display the content, and it's fine. My question is more about the 2 views taking the user to that content. I used UITableViewControllers because that's what seemed the most appropriate for a structured hierarchy like this one. But that doesn't seem like the best solution in term of user experience.. What structure / "view-flow" / kind of presentation would you try to implement in my situation? As always, any help would be greatly appreciated! Just so you can understand better the hierarchy, with a simple example : -----> Section 1 -----> SubSection 1.1 -----> Content | -----> SubSection 1.2 -----> Content | -----> SubSection 1.3 -----> Content | | | UINavigationController -------> Section 2 -----> SubSection 2.1 -----> Content | -----> SubSection 2.2 -----> Content | -----> SubSection 2.3 -----> Content | -----> SubSection 2.4 -----> Content | -----> SubSection 2.5 -----> Content | -----> Section 3 -----> SubSection 3.1 -----> Content -----> SubSection 3.2 -----> Content |------------------| |--------------------| |-------------| 1 UITableViewController 3 UITableViewControllers 10 UIViewControllers (3 rows) (with different with a UIWebView number of rows)

  Read the article

• How do I server multiple domains from the same directory and codebase without my configuraton breaking when apache.conf is overwritten?

  - by neokio

  I have 20 domains on a VPS running cPanel. One public_html is filled with code, the remaining 19 are symbolic links to that one. (For example, assets is a directory within public_html ... for the 19 others, there's a symbolic link to that directory in each each accounts public_html dir.) It's all PHP / MySQL database driven, with content changing depending on the domain. It works like a charm, assuming cPanel has suExec enabled correctly, and assuming apache.conf does NOT have SymLinksIfOwnerMatch enabled. However, every few weeks, my apache.conf is mysteriously overwritten, re-enabling SymLinksIfOwnerMatch, and disabling all 19 linked sites for as long as it takes for me to notice. Here's the offending line in apache.conf: <Directory "/"> AllowOverride All Options ExecCGI FollowSymLinks IncludesNOEXEC Indexes SymLinksIfOwnerMatch </Directory> The addition of SymLinksIfOwnerMatch disables the sites in a strange way ... the html is generated correctly, but all css/js/image in the html fails to load. Clicking any link redirects to /. And I have no idea why. I do have a few things in my .htaccess, which work fine when SymLinksIfOwnerMatch is not present: <IfModule mod_rewrite.c> # www.example.com -> example.com RewriteCond %{HTTPS} !=on RewriteCond %{HTTP_HOST} ^www\.(.+)$ [NC] RewriteRule ^ http://%1%{REQUEST_URI} [R=301,L] # Remove query strings from static resources RewriteRule ^assets/js/(.*)_v(.*)\.js /assets/js/$1.js [L] RewriteRule ^assets/css/(.*)_v(.*)\.css /assets/css/$1.css [L] RewriteRule ^assets/sites/(.*)/(.*)_v(.*)\.css /assets/sites/$1/$2.css [L] # Block access to hidden files and directories RewriteCond %{SCRIPT_FILENAME} -d [OR] RewriteCond %{SCRIPT_FILENAME} -f RewriteRule "(^|/)\." - [F] # SLIR ... reroute images to image processor RewriteCond %{REQUEST_URI} ^/images/.*$ RewriteRule ^.*$ - [L] # ignore rules if URL is a file RewriteCond %{REQUEST_FILENAME} !-f # ignore rules if URL is not php #RewriteCond %{REQUEST_URI} !\.php$ # catch-all for routing RewriteRule . index.php [L] </ifModule> I also use most of the 5G Blacklist 2013 for protection against exploits and other depravities. Again, all of this works great, except when SymLinksIfOwnerMatch gets added back into apache.conf. Since I've failed to find the cause of whatever cPanel/security update is overwriting apache.conf, I thought there might be a more correct way to accomplish my goal using group permissions. I've created a 'www' group, added all accounts to the group, and chmod -R'd the code source to use that group. Everything is 644 or 755. But doesn't seem to be enough. My unix isn't that strong. Do you need to restart something for group changes to take effect? Probably not. Anyways, I'm entering unknown territory. Can anyone recommend the right way to configure a website for multiple sites using one codebase that doesn't rely on apache.conf?

  Read the article

• Solaris OpenStack Horizon customizations

  - by GirishMoodalbail-Oracle

  In Oracle Solaris OpenStack Havana, we have customized the Horizon BUI by modifying existing dashboard and panels to reflect only those features that we support. The modification mostly involves:  --  disabling an widget (checkbox, button, textarea, and so on) --  removal of a tab from a panel --  removal of options from pull-down menus The following table lists the customizations that we have made. |-----------------------------+-----------------------------------------------------| | Where                       | What                                                | |-----------------------------+-----------------------------------------------------| | Project => Instances =>     | Post-Creation tab is removed.                       | | Launch Instance             |                                                     | |                             |                                                     | | Project => Instances =>     | Security Groups tab is removed.                     | | Actions => Edit Instance    |                                                     | |                             |                                                     | | Project => Instances =>     | Console tab is removed.                             | | Instance Name               |                                                     | |                             |                                                     | | Project => Instances =>     | Following actions Console, Edit Security Groups,    | | Actions                     | Pause Instance, Suspend Instance, Resize Instance,  | |                             | Rebuild Instance, and Migrate Instance are removed. | |                             |                                                     | | Project =>                  | Security Groups tab is removed.                     | | Access and Security         |                                                     | |                             |                                                     | | Project =>                  | Create Volume action is removed.                    | | Images and Snapshots =>     |                                                     | | Images => Actions           |                                                     | |                             |                                                     | | Project => Networks =>      | Admin State is disabled and its value is always     | | Create Network              | true.                                               | |                             |                                                     | | Project => Networks =>      | Disable Gateway checkbox is disabled, and its       | | Create Network =>           | value is always false.                              | | Subnet                      |                                                     | |                             |                                                     | | Project => Networks =>      | Allocation Pools and Host Routes text area are      | | Create Network =>           | disabled.                                      | | Subnet Detail               |                                                     | |                             |                                                     | | Project => Networks =>      | Edit Subnet action is removed.                      | | Network Name => Subnet =>   |                                                     | | Actions                     |                                                     | |                             |                                                     | | Project => Networks =>      | Edit Port action is removed.                        | | Network Name => Ports =>    |                                                     | | Actions                     |                                                     | |                             |                                                     | | Admin => Instnaces =>       | Following actions Console, Pause Instance,          | | Actions                     | Suspend Instance, and Migrate Instance are removed. | |                             |                                                     | | Admin => Networks =>        | Edit Network action is removed                      | | Actions                     |                                                     | |                             |                                                     | | Admin => Networks =>         | Edit Subnet action is removed                       | | Subnets => Actions          |                                                     | |                             |                                                     | | Admin => Networks =>         | Edit Port action is removed                         | | Ports => Actions            |                                                     | |                             |                                                     | | Admin => Networks =>         | Admin State and Shared check box are disabled.      | | Create Network              | Network's Admin State is always true, and Shared is | |                             | always false.                                       | |                             |                                                     | | Admin => Networks =>        | Admin State check box is disabled and its value     | | Network Name => Create Port | is always true.                                     | |-----------------------------+-----------------------------------------------------|

  Read the article

• laptop will not boot after attempting upgrade to 13.10

  - by naerwenya

  I wanted to update my OS to the new 14.04 LTS. I was running 12.04 LTS before and followed the advice that upgrades should be done in steps. I first upgraded to 12.10, which seemed to work fine, and later to 13.10. This was all done through the Software Manager. After the last upgrade, I am no longer able to boot up my computer. The GNU GRUB menu opens up, but after selecting Ubuntu, it just stalls with a blank purple screen. If I select one of the other kernels, it also stalls after "Loading initial ramdisk...". I can't get into the Recovery Menu, either. I'm still rather new to Linux and may have possibly made the situation worse. Unfortunately, nothing has worked yet. I tried reinstalling from a flash drive and on my first attempt, the wizard recognised a previous installation. Unfortunately, the wizard also didn't like how my partitions were set up (I didn't change anything) and gave an error before closing. Unfortunately, I didn't write the error down, but it was about the boot partition. On the next attempt and ever since, the installation wizard has stated that "This computer currently has no detected operating systems." This is strange, because I could see the disk and even access my files when booting up from the USB. At this point, I decided to back up my important files using dropbox. Before losing all my files, I wanted to try the Boot-Repair tool, which also produced no results, and the files are no longer visible when booting from USB. The link to the Boot-Repair log is at http://paste.ubuntu.com/7457249/. If I then proceed through to the "Something else" installation option, I can see that the partitions still exist. This is what they look like: /dev/sda free space (size indicated 1MB) /dev/sda1 efi (33MB of 98 MB used) /dev/sda2 efi (352634MB of 746330MB used) /dev/sda3 swap (3725MB, none used) free space (0MB) Is there any way I might be able to get my computer to work and preserve my files as well?

  Read the article

• Mount CIFS share gives "mount error 127 = Key has expired"

  - by djk

  Hi, I'm currently replicating the setup of a CentOS box an am running into a strange error while trying to mount a samba share that resides on a NAS. The error I'm getting is: mount error 127 = Key has expired Refer to the mount.cifs(8) manual page (e.g.man mount.cifs) The settings are identical to the old machine, the password is definitely correct as well. I have googled the issue of course, and looked at every single page that references this issue (not that many) and have still not found an answer. The older CentOS box is using version 3.0.28-0.el4.9 of Samba and the one I'm trying to setup now is 3.0.33-3.7.el5_3.1. I don't know if this has anything to do with it but it's certainly one of the only differences between the 2 setups. When I try the mount command this appears in the syslog: Sep 8 10:51:54 helvetica2 kernel: Status code returned 0xc0000072 NT_STATUS_ACCOUNT_DISABLED Sep 8 10:51:54 helvetica2 kernel: CIFS VFS: Send error in SessSetup = -127 Sep 8 10:51:54 helvetica2 kernel: CIFS VFS: cifs_mount failed w/return code = -127 The account is very much not disabled as it works on the old box using the same credentials. Has anyone else seen this problem? Thanks!

  Read the article

• LSI RAID monitor reports "Consistency Check inconsistency logging disabled"

  - by carlpett

  I have a server with a LSI MegaRAID 9261-8i controller. Recently I started getting alerts like this one: Controller ID: 1 Consistency Check inconsistency logging disabled, too many inconsistencies on VD: 0 Generated on:Sat May 12 04:06:40 2012 SYSTEM DETAILS--- IP Address: 192.168.1.29 OS Name: Windows 7 x64 OS Version: 6.01 Driver Name: megasas.sys Driver Version: 4.5.1.64 IMAGE DETAILS--- BIOS Version: 2.120.33-1197 Firmware Package Version: 12.12.0-0045 Firmware Version: 3.21.00_4.11.05.00_0x05000000 VD 0 is a RAID mirror containing the system disk. I have searched and read, but cannot find any trace of how to actually do anything about this. I tried running a scandisk but that did not find anything (as I expected, since scandisk reads the disks as exposed by the controller, right?). The MegaRAID Storage Manager does not as far as I can see have any options for checking or fixing physical disks. The program claims the VD is "healty", and both disks have Error count 0. Also a bit strange is the System details in the message... The IP address is associated with the RAS (dial in) interface, and the OS should be Windows Server 2011 SBS. Has anyone else experienced this before? What can be done?

  Read the article

• Apache 2.4 + PHP-FPM + ProxyPassMatch

  - by apfelbox

  I recently installed Apache 2.4 on my local machine, together with PHP 5.4.8 using PHP-FPM. Everything went quite smoothly (after a while...) but there is still a strange error: I configured Apache for PHP-FPM like this: <VirtualHost *:80> ServerName localhost DocumentRoot "/Users/apfelbox/WebServer" ProxyPassMatch ^/(.*\.php(/.*)?)$ fcgi://127.0.0.1:9000/Users/apfelbox/WebServer/$1 </VirtualHost> It works, for example if I call http://localhost/info.php I get the correct phpinfo() (it is just a test file). If I call a directory however, I get a 404 with body File not found. and in the error log: [Tue Nov 20 21:27:25.191625 2012] [proxy_fcgi:error] [pid 28997] [client ::1:57204] AH01071: Got error 'Primary script unknown\n' Update I now tried doing the proxying with mod_rewrite: <VirtualHost *:80> ServerName localhost DocumentRoot "/Users/apfelbox/WebServer" RewriteEngine on RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^/(.*\.php(/.*)?)$ fcgi://127.0.0.1:9000/Users/apfelbox/WebServer/$1 [L,P] </VirtualHost> But the problem is: it is always redirecting, because on http://localhost/ automatically http://localhost/index.php is requested, because of DirectoryIndex index.php index.html Update 2 Ok, so I think "maybe check whether there is a file to give to the proxy first: <VirtualHost *:80> ServerName localhost DocumentRoot "/Users/apfelbox/WebServer" RewriteEngine on RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_FILENAME} -f RewriteRule ^/(.*\.php(/.*)?)$ fcgi://127.0.0.1:9000/Users/apfelbox/WebServer/$1 [L,P] </VirtualHost> Now the complete rewriting does not work anymore... Update 3 Now I have this solution: ServerName localhost DocumentRoot "/Users/apfelbox/WebServer" RewriteEngine on RewriteCond /Users/apfelbox/WebServer/%{REQUEST_FILENAME} -f RewriteRule ^/(.*\.php(/.*)?)$ fcgi://127.0.0.1:9000/Users/apfelbox/WebServer/$1 [L,P] First check, that there is a file to pass to PHP-FPM (with the full and absolute path) and then do the rewriting. This does not work when using URL rewriting inside a subdirectory, also it fails for URLs like http://localhost/index.php/test/ So back to square one. Any ideas?

  Read the article

• Windows telling me, the local security authority is internally inconsistent upon mounting a network drive

  - by acme

  Since ages I've mounted a network share (via samba to a Linux machine) in Windows 7 to access it via drive letter. This worked flawlessly so far. Until now. Suddenly I couldn't access the drive anymore. Windows was telling me the network name (I didn't remember the exact term) was already in use. So I disconnected and tried to connect again: net use Y: \\10.10.10.208\work After a long time I get a message saying "The Local Security Authority (LSA) database contains an internal inconsistency" A restart didn't help. The mapped share is accessible (works on other machines in the same network), so obviously something strange is going on on my machine. Can anyone tell me how I can fix this inconsistency? Update: All machines that have saved the login information refuse with this error. So it must be something with the authorization. When I use net use Y: \\10.10.10.208\work /user:raphael it prompts me for the password and then returns that error message.

  Read the article

• Windows Server 2008 R2 Server Manager not working -> mmc.exe crashes with System.IO.FileNotFoundException

  - by Aleja_Vigo

  Since some days ago I can't run the Server Manager, it fails like this: Descripción: Stopped working Firma con problemas: Nombre del evento de problema: CLR20r3 Firma del problema 01: mmc.exe Firma del problema 02: 6.1.7600.16385 Firma del problema 03: 4a5bc808 Firma del problema 04: System.Management Firma del problema 05: 2.0.0.0 Firma del problema 06: 4ca2baf0 Firma del problema 07: 32f Firma del problema 08: 12b Firma del problema 09: System.IO.FileNotFoundException Versión del sistema operativo: 6.1.7601.2.1.0.272.7 There are other strange syntoms in the SO: Hyper-V stopped working as well, fails to load any VM information The desktop icons rearrange themselves all the time, and always on boot, after I move them. I use now an app that remembers their position to restore it... Windows Update service dissapeared, along with BITS service, I managed to recover them and installed all updates availables today I'm going nuts looking for information about these errors. Solutions that didn't work: sfc /scannow Doesn't complain about anything All windows updates applied (after recovering missing Windows Update) ServerManager.log: Only one error all the time: Error (Id=0) System.Runtime.InteropServices.COMException (0x800706D9): No hay más extremos disponibles desde el asignador de extremos. (Excepción de HRESULT: 0x800706D9) en Microsoft.Windows.ServerManager.NativeMethods.INetFwPolicy2.IsRuleGroupCurrentlyEnabled(String group) en Microsoft.Windows.ServerManager.DirectResult.GetRemoteManagementEnabled() In english : "There are no more endpoints available from the endpoint mapper" Where could I see which is the infamous file that mmc.exe is looking for in that System.IO.FileNotFoundException?? Please, any light on this would be much appreciated...

  Read the article

• Mount CIFS share gives "mount error 127 = Key has expired"

  - by djk

  I'm currently replicating the setup of a CentOS box an am running into a strange error while trying to mount a samba share that resides on a NAS. The error I'm getting is: mount error 127 = Key has expired Refer to the mount.cifs(8) manual page (e.g.man mount.cifs) The settings are identical to the old machine, the password is definitely correct as well. I have googled the issue of course, and looked at every single page that references this issue (not that many) and have still not found an answer. The older CentOS box is using version 3.0.28-0.el4.9 of Samba and the one I'm trying to setup now is 3.0.33-3.7.el5_3.1. I don't know if this has anything to do with it but it's certainly one of the only differences between the 2 setups. When I try the mount command this appears in the syslog: Sep 8 10:51:54 helvetica2 kernel: Status code returned 0xc0000072 NT_STATUS_ACCOUNT_DISABLED Sep 8 10:51:54 helvetica2 kernel: CIFS VFS: Send error in SessSetup = -127 Sep 8 10:51:54 helvetica2 kernel: CIFS VFS: cifs_mount failed w/return code = -127 The account is very much not disabled as it works on the old box using the same credentials. Has anyone else seen this problem? Thanks!

  Read the article

• Replication of lockoutTime attribute is not urgent on AD-LDS

  - by ixe013

  I have two LDS servers on the same subnet. They replicate well. If I change an attribute, it gets replicated after 15 seconds. LDS is configured to honor password policies. When a user makes too many wrong password attemps, his account is locked and that user's lockoutTime attribute is set accordingly. But lockoutTime is not replicated as urgent. In fact, it is not replicated unless there is another change somewhere in the directory. The lockoutTime attribute will be replicated. Here is an (edited Wireshark) trace. It shows normal replication trafic No. Time Protocol Length Info 133 16:23:02 DRSUAPI 562 DsGetNCChanges request 134 16:23:02 DRSUAPI 3042 DsGetNCChanges response 152 16:23:17 DRSUAPI 562 DsGetNCChanges request 157 16:23:17 DRSUAPI 242 DsGetNCChanges response 230 16:24:57 DRSUAPI 562 DsGetNCChanges request 231 16:24:57 DRSUAPI 2930 DsGetNCChanges response 246 16:25:12 DRSUAPI 562 DsGetNCChanges request Right after that, I lock the user (with a FOR loop and ldifde). Nothing happens, until I give up and change the description attribute on the user, then about 15 seconds later I see the replication go through. 1984 16:31:05 DRSUAPI 562 DsGetNCChanges request 1985 16:31:05 DRSUAPI 2930 DsGetNCChanges response The lockoutTime and description is replicated. As stated here, if I set lockoutTime to 0, replication occurs after 15 seconds ! I have enabled replication diagnostics, but nothing shows up in the instance's logs - strange. I have enabled change notification between sites, restarted both services, but I did not see any changes. How can I make the lockoutTime replication urgent ?

  Read the article

• WDS's MDT DeploymentShare and REMINST replicated with DFS-R does not read WIM from local WDS

  - by mbrownnyc

  I've read several guides on using DFS-R with WDS and MDT to replicate REMINST and DeploymentShare, and I have a particularly strange problem. On the receiving server, after configuring WDS and mounting the DeploymentShare into MDT's DeploymentWorkbench, I also performed the following: 1) in .\Control\Bootstrap.ini, changed DeployRoot to \%wdsserver%\DeploymentShare$ 2) Changed the UNC path at the root of the MDT Deployment Share in the DeploymentWorkbench to match that of the current server. 3) In Unattend.xml files located: .\Control**, modified the following value to match the current server: <cpi:offlineImage catelog://HOST/ I am able to boot and grab the LiteTouch PE image off the local WDS TFTP server, but the WIM files, the scripts, everything else is being pulled off the WDS server at the remote site (the original WDS server that was the source of the files within the DFS-R replicated folder). What do I do in order to solve this problem? I've grepped all the files below the DeploymentShare to look for instances of the hostname of the WDS server at the remote site (the source of the files), but I found none. Here are the guides I referred to: http://technet.microsoft.com/en-us/library/cc771324%28WS.10%29.aspx http://blogs.technet.com/b/askds/archive/2009/12/16/wds-and-dfsr-love-at-first-sync.aspx http://oasysadmin.com/2011/11/03/copying-moving-and-replicating-the-mdt-2010-deployment-share/

  Read the article

• HP SmartArray P400: How to repair failed logical drive?

  - by TegtmeierDE

  I have a HP Server with SmartArray P400 controller (incl. 256 MB Cache/Battery Backup) with a logicaldrive with replaced failed physicaldrive that does not rebuild. This is how it looked when I detected the error: ~# /usr/sbin/hpacucli ctrl slot=0 show config Smart Array P400 in Slot 0 (Embedded) (sn: XXXX) array A (SATA, Unused Space: 0 MB) logicaldrive 1 (698.6 GB, RAID 1, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SATA, 750 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SATA, 750 GB, OK) array B (SATA, Unused Space: 0 MB) logicaldrive 2 (2.7 TB, RAID 5, Failed) physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SATA, 750 GB, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SATA, 750 GB, OK) physicaldrive 2I:1:5 (port 2I:box 1:bay 5, SATA, 750 GB, OK) physicaldrive 2I:1:6 (port 2I:box 1:bay 6, SATA, 750 GB, Failed) physicaldrive 2I:1:7 (port 2I:box 1:bay 7, SATA, 750 GB, OK) unassigned physicaldrive 2I:1:8 (port 2I:box 1:bay 8, SATA, 750 GB, OK) ~# I thought that I had drive 2I:1:8 configured as a spare for Array A and Array B, but it seems this was not the case :-(. I noticed the problem due to I/O errors on the host, even if only 1 physicaldrive of the RAID5 is failed. Does someone know why this could happen? The logicaldrive should go into "Degraded" mode but still be fully accessible from the host os!? I first tried to add the unassigned drive 2I:1:8 as a spare to logicaldrive 2, but this was not possible: ~# /usr/sbin/hpacucli ctrl slot=0 array B add spares=2I:1:8 Error: This operation is not supported with the current configuration. Use the "show" command on devices to show additional details about the configuration. ~# Interestingly it is possible to add the unassigned drive to the first array without problems. I thought maybe the controller put the array into "failed" state due to the missing spare and protects failed arrays from modification. So I tried was to reenable the logicaldrive (to add the spare afterwards): ~# /usr/sbin/hpacucli ctrl slot=0 ld 2 modify reenable Warning: Any previously existing data on the logical drive may not be valid or recoverable. Continue? (y/n) y Error: This operation is not supported with the current configuration. Use the "show" command on devices to show additional details about the configuration. ~# But as you can see, re-enabling the logicaldrive this was not possible. Now I replaced the failed drive by hotswapping it with the unassigned drive. The status now looks like this: ~# /usr/sbin/hpacucli ctrl slot=0 show config Smart Array P400 in Slot 0 (Embedded) (sn: XXXX) array A (SATA, Unused Space: 0 MB) logicaldrive 1 (698.6 GB, RAID 1, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SATA, 750 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SATA, 750 GB, OK) array B (SATA, Unused Space: 0 MB) logicaldrive 2 (2.7 TB, RAID 5, Failed) physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SATA, 750 GB, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SATA, 750 GB, OK) physicaldrive 2I:1:5 (port 2I:box 1:bay 5, SATA, 750 GB, OK) physicaldrive 2I:1:6 (port 2I:box 1:bay 6, SATA, 750 GB, OK) physicaldrive 2I:1:7 (port 2I:box 1:bay 7, SATA, 750 GB, OK) ~# The logical drive is still not accessible. Why is it not rebuilding? What can I do? FYI, this is the configuration of my controller: ~# /usr/sbin/hpacucli ctrl slot=0 show Smart Array P400 in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: XXXX Cache Serial Number: XXXX RAID 6 (ADG) Status: Enabled Controller Status: OK Chassis Slot: Hardware Revision: Rev E Firmware Version: 5.22 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Analysis Inconsistency Notification: Disabled Raid1 Write Buffering: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Accelerator Ratio: 25% Read / 75% Write Drive Write Cache: Disabled Total Cache Size: 256 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True ~# Thanks for you help in advance.

  Read the article

• SQL Server 2008 R2 Enterprise won't install on Windows 2008 R2 Enterprise

  - by Carlos Paulino

  I've been trying to install SQL Server on a new Windows Server 2008. I have tried everything but I haven't been able to narrow down the problem. When the installation fails I get " Exit code (Decimal): -2068643839". The problem with this is that according to Microsoft this is a generic error code. I follow their guide to look into the detail.txt inside C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\ But I can't find something that specifies the exact error. Any suggestions ? Thanks in advanced. I uploaded to detail.txt to http://www.megaupload.com/?d=0MV46SZH because it is to big to paste here. Below is the summary.txt ---------- Overall summary: Final result: SQL Server installation failed. To continue, investigate the reason for the failure, correct the problem, uninstall SQL Server, and then rerun SQL Server Setup. Exit code (Decimal): -2068643839 Exit facility code: 1203 Exit error code: 1 Exit message: SQL Server installation failed. To continue, investigate the reason for the failure, correct the problem, uninstall SQL Server, and then rerun SQL Server Setup. Start time: 2011-02-28 11:29:56 End time: 2011-02-28 11:34:45 Requested action: Install Machine Properties: Machine name: SA-SERVER Machine processor count: 8 OS version: Windows Server 2008 R2 OS service pack: Service Pack 1 OS region: United States OS language: English (United States) OS architecture: x64 Process architecture: 64 Bit OS clustered: No Product features discovered: Product Instance Instance ID Feature Language Edition Version Clustered Package properties: Description: SQL Server Database Services 2008 R2 ProductName: SQL Server 2008 R2 Type: RTM Version: 10 SPLevel: 0 Installation location: F:\x64\setup\ Installation edition: ENTERPRISE User Input Settings: ACTION: Install ADDCURRENTUSERASSQLADMIN: True AGTSVCACCOUNT: NT AUTHORITY\SYSTEM AGTSVCPASSWORD: ***** AGTSVCSTARTUPTYPE: Manual ASBACKUPDIR: Backup ASCOLLATION: Latin1_General_CI_AS ASCONFIGDIR: Config ASDATADIR: Data ASDOMAINGROUP: <empty> ASLOGDIR: Log ASPROVIDERMSOLAP: 1 ASSVCACCOUNT: <empty> ASSVCPASSWORD: ***** ASSVCSTARTUPTYPE: Automatic ASSYSADMINACCOUNTS: <empty> ASTEMPDIR: Temp BROWSERSVCSTARTUPTYPE: Disabled CONFIGURATIONFILE: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20110228_112601\ConfigurationFile.ini CUSOURCE: ENABLERANU: False ENU: True ERRORREPORTING: False FARMACCOUNT: <empty> FARMADMINPORT: 0 FARMPASSWORD: ***** FEATURES: SQLENGINE,BIDS,CONN,IS,BC,SDK,SSMS,ADV_SSMS,SNAC_SDK,OCS FILESTREAMLEVEL: 0 FILESTREAMSHARENAME: <empty> FTSVCACCOUNT: <empty> FTSVCPASSWORD: ***** HELP: False IACCEPTSQLSERVERLICENSETERMS: False INDICATEPROGRESS: False INSTALLSHAREDDIR: C:\Program Files\Microsoft SQL Server\ INSTALLSHAREDWOWDIR: C:\Program Files (x86)\Microsoft SQL Server\ INSTALLSQLDATADIR: <empty> INSTANCEDIR: D:\SQLServer INSTANCEID: MSSQLSERVER INSTANCENAME: MSSQLSERVER ISSVCACCOUNT: NT AUTHORITY\SYSTEM ISSVCPASSWORD: ***** ISSVCSTARTUPTYPE: Automatic NPENABLED: 0 PASSPHRASE: ***** PCUSOURCE: PID: ***** QUIET: False QUIETSIMPLE: False ROLE: AllFeatures_WithDefaults RSINSTALLMODE: FilesOnlyMode RSSVCACCOUNT: NT AUTHORITY\NETWORK SERVICE RSSVCPASSWORD: ***** RSSVCSTARTUPTYPE: Automatic SAPWD: ***** SECURITYMODE: SQL SQLBACKUPDIR: <empty> SQLCOLLATION: SQL_Latin1_General_CP1_CI_AS SQLSVCACCOUNT: NT AUTHORITY\SYSTEM SQLSVCPASSWORD: ***** SQLSVCSTARTUPTYPE: Automatic SQLSYSADMINACCOUNTS: SA-SERVER\Administrator SQLTEMPDBDIR: <empty> SQLTEMPDBLOGDIR: <empty> SQLUSERDBDIR: <empty> SQLUSERDBLOGDIR: <empty> SQMREPORTING: False TCPENABLED: 1 UIMODE: Normal X86: False Configuration file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20110228_112601\ConfigurationFile.ini Detailed results: Feature: Database Engine Services Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: SQL Client Connectivity SDK Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Integration Services Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Client Tools Connectivity Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Management Tools - Complete Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Management Tools - Basic Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Client Tools SDK Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Client Tools Backwards Compatibility Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Business Intelligence Development Studio Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Feature: Microsoft Sync Framework Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Rules with failures: Global rules: Scenario specific rules: Rules report file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20110228_112601\SystemConfigurationCheck_Report.htm

  Read the article

• DNS Server address configured inside Router not working

  - by Charandeep Singh

  Well, I have an ISP router in which I have configured DNS Servers to use (Primary & Secondary) like Google DNS. It works just fine. But now I have setup a computer with DNS server (Simple DNS Plus). I got it working by settings my internal DNS Server IP Address in computer. i.e. 192.168.1.3 So, instead of settings my internal DNS IP Address in every computer in my network, I want to setup DNS Server into my router. So on every DHCP request, computer get DNS Server to use. So I configured it like this: Primary DNS: 192.168.1.3 Secondry DNS: (left blank) After applying and DNS Requests stop resolving. But strange part is DNS request does goes to DNS Server but maybe not returned back, because all DNS request were available in cache logs. I don't know why this is not working, let me know if you have any solution or wordaround for this. Thanks! Update 1: NSLOOKUP Result C:\Users\user>nslookup google.com DNS request timed out. timeout was 2 seconds. Server: UnKnown Address: 192.168.1.1 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to UnKnown timed-out

  Read the article

• IIS 7 returns 304 instead of 200

  - by Ola Herrdahl

  I have a strange issue with IIS 7. Sometimes it seems to return a 304 instead of a 200. Here is a sample request captured with Fiddler: (Note that the file requested is not located in my browsers cache yet.) GET https://[mysite]/Content/js/jquery.form.js HTTP/1.1 Accept: */* Referer: https://[mysite]/Welcome/News Accept-Language: sv-SE User-Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; WOW64; Trident/4.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; InfoPath.2; OfficeLiveConnector.1.4; OfficeLivePatch.1.3; .NET4.0C; .NET4.0E) Accept-Encoding: gzip, deflate Host: [mysite] Connection: Keep-Alive Cache-Control: no-cache Cookie: ... Note that there is no If-Modified-Since or If-None-Match in the request. But still the response is: HTTP/1.1 304 Not Modified Cache-Control: public Expires: Tue, 02 Mar 2010 06:26:08 GMT Last-Modified: Mon, 22 Feb 2010 21:58:44 GMT ETag: "1CAB40A337D4200" Server: Microsoft-IIS/7.5 X-Powered-By: ASP.NET Date: Mon, 01 Mar 2010 17:06:34 GMT Does anyone have a clue of what could be wrong here? I'm running IIS 7 on Windows Web Server 2008 R2.

  Read the article

• Do we need to explicitly pass php.ini's location to php-fpm?

  - by F21

  I am seeing a strange issue where my php.ini is not used if I do not explicitly pass it to php-fpm when starting it. This is the upstart script I am using: start on (filesystem and net-device-up IFACE=lo) stop on runlevel [016] pre-start script mkdir -p /run/php end script expect fork respawn exec /usr/local/php/sbin/php-fpm --fpm-config /etc/php/php-fpm.conf If PHP is started with the above, my php.ini is never used, even though it is in Configuration File (php.ini) Path. This is the relevant part from phpinfo(): Configuration File (php.ini) Path /etc/php/ Loaded Configuration File (none) Scan this dir for additional .ini files (none) Additional .ini files parsed (none) If I modify the last line of the upstart script to point php-fpm to php.ini explicitly: exec /usr/local/php/sbin/php-fpm --fpm-config /etc/php/php-fpm.conf -c /etc/php/php.ini Then we see that the php.ini is loaded: Configuration File (php.ini) Path /etc/php/ Loaded Configuration File /etc/php/php.ini Scan this dir for additional .ini files (none) Additional .ini files parsed (none) Why is this the case? Is this a quirk in php-fpm? Minor update: This also seems to be a problem for php5-fpm installed using apt-get. I did a test install in a Ubuntu Server 12.04 virtual machine by running the following: sudo apt-get install nginx php5-fpm PHP-FPM and nginx were started after installation and everything seemed fine. I then uncommented php's settings in nginx's configuration and placed a test phpinfo() file to inspect PHP's settings. The relevant bits are: Configuration File (php.ini) Path /etc/php5/fpm Loaded Configuration File (none) Scan this dir for additional .ini files /etc/php5/fpm/conf.d Additional .ini files parsed /etc/php5/fpm/conf.d/10-pdo.ini I noted that no php.ini was loaded either. However, if I go to /etc/php5/fpm, I can see that a php.ini exists. I also checked the start up scripts for PHP-FPM and the -c parameter was not used to link the ini file to PHP. This can potentially be confusing for people who would expect php.ini to be loaded automatically by PHP-FPM.

  Read the article

• VMware Tools in Ubuntu guest on VMware Server 2 do not build

  - by ulf

  When trying to build the VMware tools in my Ubuntu 9.10 64 bit guest on a VMware Server 2.0.2 host with Debian 5 I'm getting strange errors like: Building the vmmemctl module. Using 2.6.x kernel build system. make: Gehe in Verzeichnis '/tmp/vmware-config8/vmmemctl-only' make -C /lib/modules/2.6.31-19-server/build/include/.. SUBDIRS=$PWD SRCROOT=$PWD/. modules make[1]: Betrete Verzeichnis '/usr/src/linux-headers-2.6.31-19-server' CC [M] /tmp/vmware-config8/vmmemctl-only/backdoorGcc64.o In file included from /tmp/vmware-config8/vmmemctl-only/backdoor.h:29, from /tmp/vmware-config8/vmmemctl-only/backdoorGcc64.c:38: /tmp/vmware-config8/vmmemctl-only/vm_basic_types.h:108:7: warning: "__FreeBSD__" is not defined CC [M] /tmp/vmware-config8/vmmemctl-only/os.o In file included from /tmp/vmware-config8/vmmemctl-only/os.c:51: /tmp/vmware-config8/vmmemctl-only/compat_wait.h:78: error: conflicting types for ‘poll_initwait’ include/linux/poll.h:70: note: previous declaration of ‘poll_initwait’ was here make[2]: *** [/tmp/vmware-config8/vmmemctl-only/os.o] Fehler 1 make[1]: *** [_module_/tmp/vmware-config8/vmmemctl-only] Fehler 2 make[1]: Verlasse Verzeichnis '/usr/src/linux-headers-2.6.31-19-server' make: *** [vmmemctl.ko] Fehler 2 make: Verlasse Verzeichnis '/tmp/vmware-config8/vmmemctl-only' Unable to build the vmmemctl module. I googled half the Internet but couldn't come to a solution. None of the kernel modules seems to build correctly. While googling I read something about a bug in this kernel tree.

  Read the article

< Previous Page | 557 558 559 560 561 562 563 564 565 566 567 568  | Next Page >