Search Results

Search found 17314 results on 693 pages for 'vpn setup'.

Page 565/693 | < Previous Page | 561 562 563 564 565 566 567 568 569 570 571 572  | Next Page >

• VMWare ESXi 5 - Expanded RAID 5 array - cannot access datastore

  - by Dayton Brown

  I'm using VMWare ESXi 5 and had a 2 TB RAID 5 setup on an HP DL360 with a P400i RAID card. I added two more 1 TB drives and using the SmartStart ACU, added the drives and expanded the logical disk. Now after booting back to ESXi, the server boots, but lists no available persistent storage. I've rescanned multiple times to no avail: the Datastore doesn't show up. I booted to GParted and the 1.8TB partition shows up, but it shows as unknown. Anyone have any good ideas? EDIT: Final Solution So after much gnashing of teeth, it was fairly simple to solve. I purchased an eSata 2 TB external drive and a PCI eSata card for my server. I then used Clonezilla to image the current partitions to my new external drive. You have to check "don't check drive sizes" in advanced mode, otherwise it will yell at you for have a smaller drive. For some reason my PCI card wouldn't boot on my HP server, so I hooked the drive up to another desktop I had, booted to VMWare, and copied the vmdk's to another drive. I'm going to blow out the RAID config and then create 1.5TB logical drives.

  Read the article

• How to restart boot Windows 7 after upgrading to a SSHD on SONY VAIO with recovery discs?

  - by Boris Okun

  The original HDD on my Sony VAIO still works, but has a damaged sector 0 and I was constantly prompted to replace the HDD because of the imminent failure. I created recovery discs as instructed, used a USB external HDD for complete back up (including Windows image back up). After installing the SSHD and using recovery discs to upload Windows and boot, I am getting the Windows welcome screen. Right after that, I'm getting the following message: Windows couldn't complete the installation. To install Windows on this computer, restart the installation. I have tried repeating the process many times all kinds of different ways and I still receive the same message. Also, when I tried to change to partitioning as the other option offered, I get the message: Windows Setup could not configure Windows to run on this computer's hardware. All troubleshooting for hardware and PCU came out solid. I tried to load the image back up from the external drive, but can't load the driver. The computer doesn't see it. Does anyone have a clue or has encountered something similar?

  Read the article

• netlogon errors

  - by rorr

  I have two instances of mssql 2005 and am using CA XOSoft replication. The master is a failover cluster and the replica is a standalone server. They are all running Server 2003 sp2 x64. Same patch levels on all servers. This setup has worked great for several months until we recently restricted the RPC ports on both nodes of the master(5000 - 6000 using rpccfg.exe). We have to implement egress filtering, thus the limiting of the ports. We began receiving login errors for sql windows authentication and NETLOGON Event ID: 5719: This computer was not able to set up a secure session with a domain controller in domain due to the following: Not enough storage is available to process this command. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. We also see group policies failing to update and cluster file shares go offline at the same time. The RPC ports were set back to default when we started seeing these problems and the servers rebooted, but the problems persist. The domain controllers are not showing any errors. Running dcdiag and netdiag shows everything is fine. We have noticed that the XOSoft service ws_rep.exe is using a lot of handles(8 - 9k), about the same number that sqlserver is using. As soon as xosoft replication is stopped the login errors cease and everything functions correctly. I have opened a ticket with CA for XOSoft, but I'm not sure that the problem is actually xosoft, but that it is the one bringing the problem to light. I'm looking for tips on debugging RPC problems. Specifically on limiting the ports and then reverting the changes.

  Read the article

• Windows 7 Busy Icon won't stop spinning

  - by Lynda

  In windows 7 you have the busy icon that is a little blue wheel spinning beside the cursor when it is doing something. It has started to spin for about a second every 3-5 seconds. There is noting running that I can tell on the computer to cause the busy icon. It gets very annoying and I am not sure what to do to get it to stop. Ideas? Running a CPU Usage Gadget says I have less than 5% of the CPU being use and I have over 6GB of RAM free. (I have 8GB total) I am running a 3.6 GHZ AMD FX 4100 processor. EDIT- What I am actually seeing is the working in background pointer (the pointer is still visible beside the busy icon). EDIT 2 - After realizing this happened with the printer installation I turned on the the printer and the busy icon stopped. The printer is setup wirelessly. How do I stop Windows from (I guess) checking for the printer? That is what I assume it is doing. I am using a HP Officejet 8600

  Read the article

• Remove directory from URL IIS 7.5

  - by xalx

  I've tried to find a solution to this and found some guides out there but none seem to work. I have the following URL - http://www.mysite.com/aboutus.html However there are some other sites which link to my old hosted site and point to http://www.mysite.com/nw/aboutus.html. My issue here is trying to remove the 'nw' directory from the URL's. I have setup the following URL Rewrite in IIS but it does not seem to do anything, <?xml version="1.0" encoding="UTF-8"?> <configuration> <system.webServer> <rewrite> <rules> <rule name="Redirect all to root folder" enabled="true" stopProcessing="true"> <match url="^nw$|^/nw/(.*)$" /> <conditions> </conditions> <action type="Redirect" url="nw/{R:1}" /> </rule> <rule name="RewriteToFile"> <match url="^(?!nw/)(.*)" /> <conditions> <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" /> </conditions> <action type="Rewrite" url="/{R:1}" /> </rule> </rules> </rewrite> </system.webServer> </configuration> Any insight would be appreciated.

  Read the article

• dhcp3-server (dhcpd) is tampering with host NIC

  - by user61000

  Hi all, I have a debian box that is serving as a router (using iptables NAT). When first turned on, everything works fine for a few minutes. Then the dhcp server assigns an IP (other than 192.168.0.1) to its' host NIC, eth0. This is NOT what I want. I just want dhcp3-server to listen on eth0, not assign it an IP, and changes the kernel routing table. This of course ruins the NAT capablities of the box. How can I tell the dhcp3-server NOT to do this? Thanks Before dhcp3-server tampers with eth0, the IP is 192.168.0.1, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 173.33.220.1 eth1 After dhcp3-server tampers with eth0, the IP is 192.168.0.3, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 192.168.0.1 eth0 default 173.33.220.1 eth1 SETUP Outbound NIC is eth1 Internal NIC is eth0 /etc/network/interfaces ... iface eth0 inet static address 192.168.0.1 netmask 255.255.255.0 /etc/default/dhcp3-server INTERFACES="eth0"

  Read the article

• Mapped network drive missing from My Computer and Explorer

  - by matt wilkie

  On a Windows XP Pro SP3 machine one network drive refuses to show up in My Computer or Explorer. The missing drive letter is G:, if that matters. Other mappings work fine. Other profiles one the same machine have no problem mapping G:. I can access the G: just fine typing it into the address bar or in CMD shell. I've used TweakUI to toggle hide/show G: with no difference. TweakUI says G: should be visible. I've logged off,on between toggles to make sure the settings are taking effect. I've looked at reg key [HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer] and made sure it's zero'd. [insert ref link here] We've limped along with this broken setup for some time, just working around it, but some applications do not allow typing in a path when choosing a place to save files and it's reached the point where it's intolerable. So, anyone have any idea why XP won't show this drive letter? or how to fix it?

  Read the article

• Centos iptables configuration for Wordpress and Gmail smtp

  - by Fabrizio

  Let me start off by saying that I'm a Centos newby, so all info, links and suggestions are very welcome! I recently set up a hosted server with Centos 6 and configured it as a webserver. The websites running on it are nothing special, just some low traffic projects. I tried to configure the server as default as possible, but I like it to be secure as well (no ftp, custom ssh port). Getting my Wordpress to run as desired, I'm running into some connection problems. 2 things are not working: installing plugins and updates through ssh2 (failed to connect to localhost:sshportnumber) sending emails from my site using the Gmail smtp (Failed to connect to server: Permission denied (13)) I have the feeling that these are both related to the iptables configuration, because I've tried everything else (I think). I tried opening up the firewall to accept traffic for ports 465 (gmail smtp) and ssh port (lets say this port is 8000), but both the issues remain. Ssh connections from the terminal are working fine though. After each change I tried implementing I restarted the iptables service. This is my iptables configuration (using vim): # Generated by iptables-save v1.4.7 on Sun Jun 1 13:20:20 2014 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp --dport 8000 -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 465 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited -A OUTPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A OUTPUT -o lo -j ACCEPT -A OUTPUT -p tcp -m tcp --dport 8000 -j ACCEPT -A OUTPUT -p tcp -m tcp --dport 465 -j ACCEPT COMMIT # Completed on Sun Jun 1 13:20:20 2014 Are there any (obvious) issues with my iptables setup considering the above mentioned issues? Saying that the firewall is doing exactly nothing in this state is also an answer... And again, if you have any other suggestions for me to increase security (considering the basic things I do with this box), I would love hear it, also the obvious ones! Thanks!

  Read the article

• Requests are making it to my app server, but not into node.js -- why?

  - by Zane Claes

  I detailed in this question on StackOverflow how some random requests are not making it from the client to my Node.js app server, resulting in a gateway timeout. In summary, identical requests are, at random, not even making it far enough to trigger a console.log() in my first line of express middleware. I need to narrow down the problem, though, to find out WHERE the traffic is being lost and it was suggested that I try a packet sniffer on my app servers. Here's my setup: 2x Load Balancers (m1.larges) 2x node.js servers (also m1.large) Here's what's interesting/unusual: the node.js servers started as PHP servers with an Apache stack and continue to serve PHP files for my domain (streamified.me). However, I use a little httpd.conf magic on the app servers so that requests to api.streamified.me get routed over port 8888 to the node.js server: RewriteCond %{HTTP_HOST} ^api.streamified.me RewriteRule ^(.*) http://localhost:8888$1 [P] So, the request hits the load balancer = goes to an app server = gets routed to port 8888 if it's intended for the API = gets handled by node.js So, in the same httpd.conf file, I turned on RewriteLogLevel 5 and then created a simple PHP+CURL script on my localhost to hit my api.streamified.me with a random URL (which should cause node.js to trigger a simple "not found" response) until it resulted in a Gateway timeout. Here, you can see that it has happened -- and the rewrite log shows that the request was definitely received by the app server and forwarded to port 8888... but it was never received by node.js (or, at least, the first line of code in the first line of middleware never gets it...) Image Link: http://i.stack.imgur.com/3OQxS.png

  Read the article

• Last (I think and hope) problems configuring SSL certificate with Apache and VirtualHosts

  - by user65567

  Finally I set apache2 to get a single certificate for all subdomains. [...] # Go ahead and accept connections for these vhosts # from non-SNI clients SSLStrictSNIVHostCheck off # Apache setup which will listen for and accept SSL connections on port 443. Listen 443 # Listen for virtual host requests on all IP addresses NameVirtualHost *:443 # Because this virtual host is defined first, it will # be used as the default if the hostname is not received # in the SSL handshake, e.g. if the browser doesn't support # SNI. <VirtualHost *:443> ServerName domain.localhost DocumentRoot "/Users/<my_user_name>/Sites/domain/public" <Directory "/Users/<my_user_name>/Sites/domain/public"> Order allow,deny Allow from all </Directory> # SSL Configuration SSLEngine on ... </VirtualHost> <VirtualHost *:443> ServerName subdomain1.domain.localhost DocumentRoot "/Users/<my_user_name>/Sites/subdomain1/public" <Directory "/Users/<my_user_name>/Sites/subdomain1/public"> Order allow,deny Allow from all </Directory> # SSL Configuration SSLEngine on ... </VirtualHost> <VirtualHost *:443> ServerName subdomain2.domain.localhost DocumentRoot "/Users/<my_user_name>/Sites/subdomain2/public" <Directory "/Users/<my_user_name>/Sites/subdomain2/public"> Order allow,deny Allow from all </Directory> # SSL Configuration SSLEngine on ... </VirtualHost> So, for example, I can correctly access https://subdomain1.domain.localhost https://subdomain2.domain.localhost ... Now, anyway, I have problems on accessing http://subdomain1.domain.localhost http://subdomain2.domain.localhost ... Since I use a Mac Os, on accessing the "http: version", I get a default page "Your website." (instead of a error). Why does it happen?

  Read the article

• Nginx proxy to IIS Connection Timeout

  - by MitMaro

  I am having an issue with random timeouts with a Nginx proxy connecting to an IIS machine. I have been watching a packet capture between the two servers and it seems that the IIS machine is receiving a SYN packet but is not responding with what I think should be an ACK response. Before the timeout occurs there seems to be a slower response from the IIS server. There is no unusual memory or processor usage on the IIS or Nginx machine. Some information on the servers and setup: Nginx Machine: Ubuntu 10.04 64bit Nginx 0.7.65 Amazon EC2 Windows Machine: Windows Server 2008 IIS 7 ASP.net Application in Integrated Mode Nginx Error: 2011/01/10 17:57:40 [error] 8297#0: *30 connect() failed (110: Connection timed out) while connecting to upstream, client: 209.***.***.***, server: secure.example.com, request: "GET /a/path/deliver.aspx HTTP/1.1", upstream: "http://***.***.***.****:****//another/path/deliver.aspx", host: "secure.example.com" WireShark Packets 6521.449528 10.***.***.*** -> 174.***.***.*** TCP 38695 > us-cli [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=477422103 TSER=0 WS=7 6524.443239 10.***.***.*** -> 174.***.***.*** TCP 38695 > us-cli [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=477422403 TSER=0 WS=7 6530.443241 10.***.***.*** -> 174.***.***.*** TCP 38695 > us-cli [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=477423003 TSER=0 WS=7

  Read the article

• nginx redirect proxy

  - by andrew

  I have a web app running on a nginx server on local ip 192.168.0.30:80 I have this in my etc/hosts 127.0.0.1 w.myapp.in If someone accesses my app using a "w" subdomain, it shows a webdav interface, otherwise it runs normally (for example, someone calls http://myapp.in , it goes into the app, and http://w.myapp.in goes into webdav interface - this is done within the app, nginx has nothing to do with it) Because I don't have a dns or anything like that, users must access the app by ip. A problem appears if someone wants to access the webdav interface, because you cannot access the app by a subdomain - unless you write a line in your local hosts file, which is not a solution) A possible solution If it's possible to setup the nginx server so that if someone calls http://192.168.0.30 (on port 80), it goes normally into the app, but if a user tries to access say http://192.168.0.30:81 (another defined port) it redirects internally to w.myapp.in, and the app sees the subdomain Given the app, can this be done? If yes, what should I put in the nginx config file? And if you guys think of a better solution, I'm open to any.

  Read the article

• How do you get AWS VPC EC2 instances to be able to see the AWS APIs?

  - by Peter Mounce

  We're spinning up infrastructure inside of an AWS VPC via CloudFormation. We're using auto-scaling groups to bring up VPC-EC2 instances (so, we don't bring up instances directly; ASGs manage that). Inside of a PVC, EC2 instances only have a private IP; they cannot see the outside world without further work. When these instances spin up, we have some bootstrap tasks that require talking to the various AWS APIs. We also have some ongoing tasks that require AWS API traffic. How are you tackling this apparent chicken-egg problem? We've read about: NAT instances - but don't like this so much because it's another layer to our stack. assigning elastic-IPs to each VPC instance that needs to talk - but a) they all do, and b) since we're using ASGs, we don't know which instances to assign EIPs to at provision-time, and c) we'd need to set up something to monitor those ASGs and assign EIPs when instances are terminated and replaced spinning up an instance (actually, a load-balanced pair, probably spanning AZs) to act as an AWS-API proxy for all API traffic I guess I'm wondering whether there's some kind of back-door we can open that allows our VPC EC2 instances access to the AWS API endpoints, but nothing else, for cheap-complexity setup, that doesn't add another network-hop layer to our infrastructure for serving requests.

  Read the article

• After adding skip-innodb mysql doesn't start

  - by Pentium10

  I am trying to setup these values: #skip-bdb #skip-locking #skip-innodb When I add them to /etc/mysql/my.cnf and even if I turn ON of of, them after I do the service restart mysql fails to start, and no error message printed. sudo service mysql restart [ ok ] Stopping MySQL database server: mysqld. [FAIL] Starting MySQL database server: mysqld . . . . . . . . . . . . . . failed! Previously I made sure that I have no InnoDB tables, and all files of that type were removed. I tried looking for error files but I couldn't locate it: /var/log/mysql.err is a 0 byte file /var/log/mysql folder has no files rsyslog was changed in past with inetutils-syslogd, and this might have changed the log files, and it could be the reason why I don't see any error logs, and I am stuck how to look or go forward.

  Read the article

• How can I create a simple Exchange 2010 backup solution?

  - by bduncanj

  I'm sure this question's been asked a dozen times in one form or another, however after much searching, there doesn't appear to be an obvious simple recovery solution for a single Exchange box. We're using Exchange 2010 on a single server, the server hosts the AD and nothing else on the network uses the AD. The intent is to run this server as you would an externally hosted Exchange server - access only via HTTP (RPC mode or OWA) - all other ports blocked. I've a daily backup running, using Windows Server 2008 volume shadow service to backup the Exchange data to an external hard disk. My question is, how do I perform a bare metal recovery of this server? 1) Do I need to be explicitly including the active directory information in this nightly backup, or will it be there by virtue of the fact that this system is the primary AD server and the Windows backup service knows this? 2) I understand I can re-install Server 2008 onto my new hardware (in the case of hardware failure) and then run Exchange 2010 setup.exe with a /recover argument, referencing the backup volume. 3) It is acceptable to have some downtime during this recovery process. But is there anything else I should be aware of? Thanks! Duncan

  Read the article

• Borked ubuntu uninstall - need to delete boot partition (i think)

  - by Max Williams

  I just got a new pc laptop with windows 7 and wanted to install Ubuntu on it. Which i did, no problem there, by downloading the installer, burning it to dvd then booting off the dvd and installing. Then, i realised that the new Ubuntu 12.04 uses the Unity desktop, which i immediately disliked, and after some research, began to hate. So, i decided (after a little googling) to install Linux Mint instead. So, thinking i'd better start from scratch, i went to the Windows 7 disk manager and wiped the Ubuntu partition that had been created. Now, when i start up, i get an error from grub, the ubuntu boot manager: error: unknown filesystem grub rescue> _ and a blinking cursor where i can enter commands. I suspect that what i've done is deleted the main ubuntu partition but NOT deleted another partition which is a boot partition, or something like that? Can anyone tell me how i can rescue or unbork this? I'd like to either a) get back to my original windows-only setup OR b) install linux mint off dvd (which i have), into the empty partition, fixing any grub confusion in the process. Any suggestions? Thanks, max BTW please don't answer if you're just going to tell me to stick with 12.04, or install a different distro or something. I definitely want Mint and just want to fix this mess - thanks :)

  Read the article

• UW-IMAP server, high load for one user

  - by Bruce Garlock

  We have been experiencing a very strange anomaly, with one specific user with our UW-IMAP server. We have about 75 users using the server, and one particular user, who is in about the middle as far as used storage keeps having issues with slow speed. Most of our users all use Thunderbird 2, or Thunderbird 3. Mostly 2, because of the performance issues we have had with 3. This user was on 3, and I downgraded him to 2. The performance has gotten better, but according to the imapd processes on the server, his username is using the most CPU % and CPU time. I've already done all the usual T/S'ing: Started profile from scratch, compacted folders, re-indexed, newer faster computer, etc.. Still, this users' imapd process is always using the most CPU on the server. For troubleshooting, we setup another user which has more usage, folders, etc.. than he does, but we don't see the users process taking up most of the CPU with the imapd process. So, it almost sounds like a particular email may be the culprit, but how can we find it, if thats the problem? This has been going on for a while, and he is a management person, so his patience is about to end. Does anyone have any ideas?

  Read the article

• Changing the default boot option without losing the boot menu

  - by hvd

  I've had a working multi-boot setup with the Windows boot loader, containing menu items for two Windows 7 systems, and one for Grub. Grub in turn contains multiple menu items, but I think that's not relevant here. I've upgraded one system to Windows 8. When I now set a different system as the default, I lose the boot menu, and I lose the possibility of booting into the other systems. I've set Windows 7 as the default, rebooted, and get Windows 7, but I don't get to choose which system to boot into. I can run its own bcdedit to change the default back to Windows 8, and another reboot shows the boot menu again, but how can I avoid defaulting to Windows 8? Here are my current boot settings, is there anything that is misconfigured? C:\WINDOWS\system32>bcdedit Windows Boot Manager -------------------- identifier {bootmgr} device partition=F: description Windows Boot Manager locale nl-NL inherit {globalsettings} integrityservices Enable default {current} resumeobject {2f8b77f0-a30b-11e1-a9c6-a4bd8d37f662} displayorder {current} {2f8b77e3-a30b-11e1-a9c6-a4bd8d37f662} {2f8b77ee-a30b-11e1-a9c6-a4bd8d37f662} toolsdisplayorder {memdiag} timeout 30 Windows Boot Loader ------------------- identifier {current} device partition=C: path \WINDOWS\system32\winload.exe description Windows 8 locale nl-NL inherit {bootloadersettings} integrityservices Enable recoveryenabled No allowedinmemorysettings 0x15000075 osdevice partition=C: systemroot \WINDOWS resumeobject {2f8b77f0-a30b-11e1-a9c6-a4bd8d37f662} nx OptIn bootmenupolicy Standard Windows Boot Loader ------------------- identifier {2f8b77e3-a30b-11e1-a9c6-a4bd8d37f662} device partition=D: path \Windows\system32\winload.exe description Windows 7 locale nl-NL osdevice partition=D: systemroot \Windows resumeobject {59616f59-a2ba-11e1-b73a-806e6f6e6963} nx OptIn pae Default bootmenupolicy Standard hypervisorlaunchtype Auto detecthal Yes sos No debug No Real-mode Boot Sector --------------------- identifier {2f8b77ee-a30b-11e1-a9c6-a4bd8d37f662} device partition=C: path \grub\winloader\grub.boot description Grub 2

  Read the article

• Cacti Login Page: Infinite loop occurs

  - by beicha

  Apache 2.2.3 | PHP 5.1.6 | MySQL 5.0.77 I followed cacti installation guide to install latest cacti 0.8.7h on CentOS 5.5 (64-bit). The installation of PHP/Apache/MySQL went smoothly until I finished the setup, and came to the login page. I can login http://.../cacti/index.php with admin account but the new page is redirected to the same login page with the message "Please enter your Cacti user name and password below" This is a infinite loop! If I use a wrong admin password I get the correct error message "Invalid User Name/Password Please Retype". [Same problem here] If I login use Guest/guest account, "Error: Access Denied, user account disabled." displays. The Cacti log file (./cacti/log/cacti.log) is empty. I Googled and seems this problem has existed for a long time, but no followup solutions were found on the forum posts I found. Anyone can help me on this problem? If more information needed, please let me know. Nov 18, 2011 UPDATE: I re-installed Cacti, this question remains UNSOLVED.

  Read the article

• Configuring IE to resolve DNS at the proxy rather than locally.

  - by dankilman

  With the intention of tunneling web traffic through an SSH connection, the following has been done: I've manually configured a PAC file in IE7 in the LAN Settings dialog. I've verified that traffic is routed through my SSH tunnel that is setup for SOCKS5 dynamic port forwarding. I see that IE7 is always trying to resolve the name locally first. What I'm looking for is the ability to have the DNS name resolved at the proxy, rather than locally by the browser. There's a setting in Firefox that specifies DNS remote resolution, and Safari does it automatically. I've verified correct operation for these 2 other browsers. It would be nice if I could get IE to work also. This is for reference so you could understand where does the question originate from. Notice: The question was actually found by the help of google but with no answers available. Considering how it is exactly my question I figured I should just copy/paste over here because I don't think I could describe any better (there is a small introduction though).

  Read the article

• How to minimize the risk of employees spreading critical information?

  - by Industrial

  Hi everyone, What's common sense when it comes to minimising the risk of employees spreading critical information to rivalling companies? As of today, it's clear that not even the US government and military can be sure that their data stays safely within their doors. Thereby I understand that my question probably instead should be written as "What is common sense to make it harder for employees to spread business critical information?" If anyone would want to spread information, they will find a way. That's the way life work and always has. If we make the scenario a bit more realistic by narrowing our workforce by assuming we only have regular John Does onboard and not Linux-loving sysadmins , what should be good precautions to at least make it harder for the employees to send business-critical information to the competition? As far as I can tell, there's a few obvious solutions that clearly has both pros and cons: Block services such as Dropbox and similar, preventing anyone to send gigabytes of data through the wire. Ensure that only files below a set size can be sent as email (?) Setup VLANs between departments to make it harder for kleptomaniacs and curious people to snoop around. Plug all removable media units - CD/DVD, Floppy drives and USB Make sure that no configurations to hardware can be made (?) Monitor network traffic for non-linear events (how?) What is realistic to do in a real world? How does big companies handle this? Sure, we can take the former employer to court and sue, but by then the damage has already been caused... Thanks a lot

  Read the article

• Can I boot up a virtual machine natively?

  - by Anshul

  My question is: Is is possible to run a virtual machine natively on your hardware if you have installed the proper drivers etc? In other words, can I use a VHD as a regular hard drive to boot from? The reason I want to do this is that I do both graphics-intensive and audio-intensive work, but my computer is not powerful enough to handle both at the same time and many times I install a bunch of audio programs that I don't want affecting the stability of my graphics programs. Basically I wanted to have sandboxing between the two sets of applications. So I tried running the graphics-intensive programs in a VirtualBox VM and the audio-intensive work natively (simply because it's a pain to route ASIO audio devices in/out of VirtualBox). This kind-of works - the graphics-intensive stuff is tolerable, but still relatively slow, because it's running inside a VM. So my next idea was to just dual-boot and install the graphics and audio programs in separate partitions but I frequently use them in tandem, so it wouldn't be practical to reboot my machine every time I need to use the other set of programs. But I could live with this scenario: If I need to do more audio-intensive stuff, I'll just boot up to the audio partition and run the graphics programs in a VM, and then when I'm working heavily on the graphics part, I'll just boot the graphics partition as a regular OS directly on the hardware. Is this possible? For example by booting up a VHD as a regular hard drive? Or by setting up dual-boot, and every time the audio partition is shut down, synchronize the graphics VM VHD with the native graphics partition? Is it practical, given the above scenario? And if it's not possible, barring buying another computer, can anyone suggest a best-of-all-worlds setup (the two worlds being performance, sandboxing, and running in parallel) for the above scenario? Thanks in advance.

  Read the article

• RAID 10 or RAID 5 for multiple VMs - what is the best choice?

  - by Lars Fastrup

  I have just ordered a new rig for my business. We do a lot of software development for Microsoft SharePoint and need the rig to run several virtual machines for development and test purposes. We will be using the free VMware ESXi for virtualization. For a start, we plan to build and start the following VMs - all with Windows Server 2008 R2 x64: Active Directory server MS SQL Server 2008 R2 Automated Build Server SharePoint 2010 Server for hosting our public Web site and our internal Intranet for a few people. The load on this server is going to be quite insignificant. 2xSharePoint 2007 development server 2xSharePoint 2010 development server Beyond that we will need to build several SharePoint farms for testing purposes. These VMs will only be started when needed. The specs of the new rig is: Dell R610 rack server 2xIntel XEON E5620 48GB RAM 6x146GB SAS drives Dell H700 RAID controller We believe the new server is going to make our VMs perform a lot better than our existing setup (2xIntel XEON, 16GB RAM, 2x500 GB SATA in RAID 1). But we are not sure about the RAID level for the new rig. Should we go for having the the 6x146GB SAS drives in a RAID 10 configuration or a RAID 5 configuration? RAID 10 seems to offer better write performance and lower risk of a RAID failure. But it comes at a cost of less drive space. Do we need RAID 10 or would RAID 5 also be a good choice for us?

  Read the article

• Retrieve a user's Exchange database in powershell

  - by Paul

  Hey Everyone, I've scoured the interwebs for a few days now off and on to find this. I am creating a powershell script for email-enabling new user's(Exchange 2007). To give you a little background when we have a new hire, their AD account is created at our off-site helpdesk, but they don't create their email account. I'm trying to automate the process of mail-enabling the user which involves putting them in the same database as an existing user, disable imap pop activesync, and lastly email the requester of the ticket. I would like to just get prompted for the New User's name, User to Replicate(mailbox, storage group, database), and the person to email after it's been created. So if someone could just help with a command to Retrieve a user's Exchange database in powershell that would be great, but if people also want to help with my hacked up script please do so as well!!! Here is what I have so far: Write-output “ENTER THE FOLLOWING DETAILS” $DName = Read-Host “User Diplay Name" $RUser = Read-Host "Replicate User(Database Grab)" ***$RData = #get the Replicate user's mailbox database here*** $REmail = #either just use a Read-Host “Requester's Email address" or ask for Requester's name and pipe through their email address by digging for it w/ powershell Enable-Mailbox -Identity "$DName" -Database "$RData" Send-MailMessage -From "John Doe <[email protected]>" -To (put $REmail here which is the Requester's email) -Subject "Test Person's email account" -Body "Test Person's email account has been setup.`n`n`nJohn Doe`nGeneric Company`nSystems Administrator`nOffice: 123.456.7890`[email protected]" -SmtpServer genericexchange.exchange.com

  Read the article

• Are these three brand new sticks of RAM really dead?

  - by David Brown

  I'm working on a Dell Dimension 4700 desktop for a friend. It came with 512MB of DDR2 RAM (two sticks of 256MB). One morning, it started blue screening on startup with no helpful error messages. It refused to boot into any form of Windows installation, including Safe Mode, original recovery disk, and my custom Windows PE disk. It did boot into the Ultimate Boot CD, so I ran memtest86, which reported errors everywhere. I removed one stick of RAM and the system booted up just fine. I moved the remaining stick into each slot and the system continued to operate normally, so I came to the conclusion that the stick that I removed was dead. I ordered an exact replacement, along with 2 more sticks of 256MB DDR2 (again, exactly the same as the original), bringing the total system memory to 1GB. Upon installing the three brand new sticks, the system blue screened again, this time stating that win32k.sys attempted to write to read-only memory. I inserted my custom Windows PE disk in order to get a better look at the memory dump with BlueScreenView, but it refused to boot and produced another blue screen, but without an error message. I removed each new stick one-by-one, restarting each time. It continued to blue screen until I was left with only the original stick. I then tried inserting the new sticks in various different orders, but this only produced more blue screens. I reinserted all three sticks (along with the original) and ran memtest86 again, which reported errors all over the place. So, now I'm right back where I started. I don't think it could be the slots themselves, because I can plug the original stick into any slot and it works just fine. System setup reports each stick correctly and shows the total as 1GB, however. It just seems strange to me that all three brand new sticks of RAM could be dead on arrival. Is there something I missed? Or should I just go ahead and RMA them?

  Read the article

< Previous Page | 561 562 563 564 565 566 567 568 569 570 571 572  | Next Page >