Search Results

Search found 2516 results on 101 pages for 'gigabit ethernet'.

Page 57/101 | < Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >

  • What software can I use to pinpoint why Windows Server 2003 takes 15 seconds for any operation?

    - by Dr. Zim
    Ram is about 1/2 in use, four CPUs are all but idle. I tried "Microsoft Server Performance Advisor" with no luck. No entries in the Event Log for hardware failures, etc. And yet I can click on the start menu and wait 15 seconds for any new attempt. Launching software takes 30 seconds to respond. The server has an 8 drive WD RE 250 gig each Dell Perc 6 Sata raid array with Intel gigabit network cards. Anyone have any software titles that could analyze what is going wrong with this server?

    Read the article

  • Turn your laptop into a wireless Access Point with Windows 7!

    - by David Nudelman
    Windows 7 offers a very cool feature where you can connect multiple devices to any wired and wireless network connection (hotel, cable, 3G, UMTS, EDGE, WIFI, RJ45, Ethernet, etc.) by turning your own laptop into a wireless AP (Access Point) to relay those devices not directly connected to the internet. For this just enter these two commands to an elevated (right click on CMD.EXE, run as administrator): netsh wlan set hostednetwork mode=allow ssid=YOURFRIENDLYSSID key=SOMEPASSWORD netsh wlan start hostednetwork At this point, if Internet Connection Sharing (ICS) is setup, anyone can connect to your SoftAP (if they know the PWD of course) and the traffic will be sent through whatever adapter you want. You can actually bridge it across an entirely different adapter... or the same on a different Wifi LAN. A GUI to set this up can be downloaded for free here: http://www.connectify.me/

    Read the article

  • RAID Read/Write Speed Gradually Slows

    - by Nalandial
    This is actually a server at home, but I felt it was sufficiently complicated as to not have it on SuperUser and could easily apply to a professional situation. I have a file server running Debian (Lenny 5.0.4), and it has an XFS LVM on top of a RAID 5 with the OS drive separate from the RAID. It's also running apache, samba, and postgresql. Side note: before anyone asks, I'm using RAID5 because I get more bang for the buck on raw drive space, and still have some fault tolerance. When the box is started (via shutdown or reboot) reading/writing to it's samba share maxes out the gigabit network connection. Over time, this slowly degrades eventually becoming < 10MB/s; however, when rebooted the speed returns to maxing out the connection. Why is this happening, and is there a way to 'clear' out whatever's causing it without taking the server down? Thanks in advance!

    Read the article

  • Why is my wi-fi STILL not working?

    - by Alex Grantham
    i have 10.10, and have gotten ndiswrapper and the proper driver, it installed properly, but still my wi-fi isn't working. In terminal it say its disabled, but its enabled EVERYWHERE... even when I exited windows. Right now i'm left to use an Ethernet cord and a second computer... please help. My windows isn't in good condition and I would love to switch to Ubuntu... but wi-fi is definitely a need. FYI, I have a toshiba satellite a505d-s6958 with the realtek rtl819[somehting something something]... but I have the driver from their webisite... I really just need to get my wifi to work

    Read the article

  • How to improve wireless network speed?

    - by Toby
    I am running 10.04 LTS on a desktop PC with a Belkin G-Plus MIMO Wireless network card. Ever since running Ubuntu on the machine I have noticed fairly slow network speeds (about half the speed I get when running the same card through Windows) I did some research I found out that by and large wireless network cards aren't that well supported on most Linux distros. I was wondering though if there is anything I could be tweaking on the system that could help squeeze a little more out of the card? Here is some more information *-network:1 description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:1c:df:24:5e:54 capabilities: ethernet physical wireless configuration: broadcast=yes ip=192.168.1.5 multicast=yes wireless=IEEE 802.11bg

    Read the article

  • RTL8168B/8111B Lan card is not detected in Redhat..Error is make ***/lib/modules/2.6.18-53.e15/build

    - by Deepak Narwal
    0 Hello friends... In My computer Lan card model is Realtek RTL8168B/8111B PCI-E GIGABIT ETHERNET NIC (NDIS 6.20) My system is dual boot windows 7 and redhat 5.1.Redhat is not picking up this model of Lan card automaticlly. I tried it by downloading from realtak site for this particular model and find some .tar packages for my kernal and when i tried to install them ... check old drivers & unload it build the module and install make */lib/modules/2.6.18-53.e15/build: no such file or directory stop make[1]: *[modules] error 2 make : [modules] error 2 i downloaded tar files from sites and unpack according to their instrution i tried to run autorun.sh script as mentioned in readme file but after doing this it is showing above error... Now what to do i am not getting

    Read the article

  • Can't find ALL wireless networks, just my neighbours

    - by motoringeek
    Been playing with live discs since 10.10 but now have gone ahead and dual booted. I have a Acer 5742z with a Nplify 802.11b/g/n wireless connection. The install went well and drivers seem to be working. BUT, although wireless detects some local networks it doesn't find mine. I have WPA-PSK security on my modem, could this be the problem?? I don't want to change my modem settings as all my other WIFI devices are contected to it. So I need help in finding my home network. A step by step guide would be useful. I am using Windows 7 now to write this but would love it if I could use Ubuntu online. I only can when I connect an Ethernet cable. Thanks in advance.

    Read the article

  • How do I turn on wireless adapter on HP Envy dv6 7200 under Ubuntu (any version)?

    - by Dave B.
    I have a new HP Envy dv6 7200 with dual boot Windows 8 / Ubuntu 12.04. In windows, the F12 key in Windows activates the "airplane mode" switch which enables/disables both on-board (mini PCIe) and USB wireless adapters. In Ubuntu, however, the wireless adapter is turned off by default and cannot be turned back on via the F12 key (or any other combination of F12 and Ctrl, Fn, Shift, etc.). Let me explain the "fixes" I've seen in various forums and explain what did or did not happen. These are listed in no particular order. (Spoiler alert: wireless is still broke). Solution 1? Use HP's "Wireless Assistant" utility to permanently activate the wireless card in Windows, then boot into Ubuntu to happily find it working. Unfortunately, this utility works in Windows 7 but not Windows 8. On the other hand, hardware drivers from HP are only available for Windows 8 for this model. Catch 22 (I could not find a comparable utility for Windows 8). Solution 2? Use a USB wireless adapter to sidestep the on-board device. I purchased such a device from thinkpenguin.com to be sure that it would be Linux-friendly. However, the wireless switch enables / disables all wireless devices including USB. So, there's my $50 donation to the nice folks at thinkpenguin.com, but still no solution. Solution 3? Following the Think Penguin folk's suggestion, modify the mini PCI express adapter following instructions here: http://www.notebookforums.com/t/225429/broken-wireless-hardware-switch-fix Tempting, but I then violate the terms of my warranty mere days after opening the box. This might be a good solution for an older machine that you want to get your geek on with, but not for a new box. Solution 4? rfkill unblock all No effect whatsoever. ubuntu@ubuntu-hp-evny:~$ rfkill unblock all ubuntu@ubuntu-hp-evny:~$ rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Solution 5? Re-install drivers. Done and done. Ubuntu recognizes the device - perhaps even without re-installing the drivers? - but cannot turn it on. How do I know this? In the Network Manager drop-down menu, the wireless option is blacked out and a message reads something like: "wireless network is disabled by a hardware switch". Solution 6? Identify a physical switch on the laptop and flip it. There is no such switch on this machine. In fact, walking through Best Buy yesterday, I checked and not a single new laptop PC had a physical switch on it. All of the wireless switches are either the F2 or F12 key ... I wonder if askubuntu will not be plagued by this exact issue in the near future? Additional info - lspci ubuntu@ubuntu-hp-evny:~$ lspci 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.2 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 3 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 08:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5229 (rev 01) 0a:00.0 Network controller: Ralink corp. Device 539b 0b:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) Any suggestions would be much appreciated!

    Read the article

  • How can you enable SMB2.0 on a router running DD-WRT?

    - by jeffreypriebe
    I think the steps are something like: Install DD-WRT on a router with an external hard-drive Install Optware to get Samba Upgrade to Samba 3.6 (the link shows Samba 3.5, but using the NSLU2 optware packages, you can get 3.6 with built-in SMB2.0) ...then a miracle occurs... Then you can use SMB2.0 to connect to your share What is step 4? I can't find it on forums, etc. Am using Microsoft Network monitor to check for SMB2.0 connection, I'm on Windows 7 and have tried network connections on wireless and gigabit wired to the router. No joy. I doubt it matters, but to get ahead of the questions: DD-WRT v24-sp2 (10/26/10) big (SVN revision 15508M NEWD-2 K2.6 Eko) on Cisco/Linksys E3000

    Read the article

  • JavaOne - Java SE Embedded Booth - Digi - Home Health Hub (HHH)

    - by David Clack
    Hi All,  So another exciting platform we will have in the booth at JavaOne is the Digi  Home Health Hub (HHH) platform. http://www.digi.com/products/wireless-wired-embedded-solutions/single-board-computers/idigi-telehealth-application-kit#overview This is a Freescale reference design that has been built by Digi, the system is powered by a Freescale i.MX28 ARM SOC, what's really exciting me is it has every wireless protocol you could ever want on a single motherboard. Ethernet, 802.11b/g/n Wi-Fi, Bluetooth, ZigBee, configurable Sub-GHz radio, NFC plus USB, audio and LCD/touch screen option. I've been experimenting with lots of wireless capable healthcare products in the last few months, plus some Bluetooth Pulse / Oxy meters, we have been looking at how the actual healthcare wireless protocols work. Steve Popovich - Vice President, Digi Internationalwill be doing a talk at the Java Embedded @ JavaOne conference in the Hotel Nikko, right next door to the JavaOne show in the Hilton. If you are registered at JavaOne you can come over to the Java Embedded @ JavaOne for $100 Come see us in booth 5605 See you there Dave

    Read the article

  • ImportError: No module named gtk

    - by Rick_2047
    after the debacle a few hours back I managed to get a working desktop after using an ethernet cable and sudo apt-get install ubuntu-desktop But now when I try to run ubuntu software center from CLI this is what I get rick@Abigail:~$ sudo software-center Traceback (most recent call last): File "/usr/bin/software-center", line 34, in <module> import gtk ImportError: No module named gtk Any guesses how to fix this. The search box on synaptic is also missing. It has something to do with module named axi. I think the both are related.

    Read the article

  • Cant get internet connection at all on Ubuntu 13.04

    - by James Ellis
    I installed Ubuntu 13.04 alongside my Windows Vista, at the start of installation it doesn't connect to the internet to download updates during installation, also during installation towards the end it removes a lot of stuff that i couldn't catch the details of at the time, it won't find my internet connection even though windows does, i tried using the ethernet cable but it wouldn't pick that up either. So i clicked in Ubuntu... System, network-Browse Internet, then Windows Internet and it said "failed to retrieve share list from server:no such file or directory" how can i get Ubuntu to find my internet???

    Read the article

  • DSL connection can't connect once disconnected

    - by Aj264
    I have setup a DSL PPPoE connection, over my cable modem, connected to my laptop via ethernet. I have saved the user name and password and set it to connect automatically. This works well when ubuntu starts and i am connected to internet. But if i try to disconnect and then reconnect, the connection wont be established. I have to restart or log out and log in, in order for ubuntu to establish the DSL connection. Any idea why this is happening? I am on ubuntu 11.10 64 bit.

    Read the article

  • How can I share the TV card on my home network? with a solution like `ln -s`?

    - by Boris
    My environment: - 2 PCs, a desktop and a laptop, both on Oneiric - they are connected together by ethernet wire - nfs-common is installed and configured: the desktop is the server - a TV tuner card is installed on the desktop, I can watch the French TNT TV with the software Me-TV It works fine, TV on desktop, and my network too: I share folders thanks to NFS. But I would like more: how can I share my TV tuner card from the desktop and be able to watch TV on the laptop too? If possible I would like a solution that allows me to keep using the software Me-TV, on both PCs. I bet that there is a solution to create a fake TV card on the 2nd PC. Something like ln -s on /dev/dvb/adapter0/.

    Read the article

  • My wireless is hard-blocked

    - by Cristian
    I'm new to linux and i am having trouble getting my wireless to work I've found the following things Wireless LAN Soft blocked: no Hard blocked: yes and : *-network DISABLED description: Wireless interface product: RT3090 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 6c:62:6d:19:38:b9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.2.0-25-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:fdfe0000-fdfefff Can you please tell me what to do?

    Read the article

  • Repeated disconnects on WPA PEAP network

    - by exasperated
    My school has a WPA PEAP network with GTC inner authentication. I am able to connect to the network, but once I load a website or two, the network become unresponsive (i.e. in Chromium, it gets stuck at "Sending request"), and I'm eventually disconnected. Any help will be greatly appreciated. Here's some log output. I can provide more if needed: Ubuntu 13.04 3.8.0-32-generic x86_64 lsusb: 03:00.0 Network controller: Intel Corporation Centrino Advanced-N 6235 (rev 24) lsmod: iwldvm                241872  0  mac80211              606457  1 iwldvm iwlwifi               173516  1 iwldvm cfg80211              511019  3 iwlwifi,mac80211,iwldvm dmesg: [    3.501227] iwlwifi 0000:03:00.0: irq 46 for MSI/MSI-X [    3.503541] iwlwifi 0000:03:00.0: loaded firmware version 18.168.6.1 [    3.527153] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUG disabled [    3.527162] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUGFS enabled [    3.527170] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled [    3.527178] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [    3.527186] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_P2P disabled [    3.527192] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Advanced-N 6235 AGN, REV=0xB0 [    3.527240] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [    3.551049] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [  375.153065] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [  375.159727] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [  375.553201] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [  375.559871] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 1892.110738] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 1892.117357] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5227.235372] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 5227.242122] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5817.817954] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 5817.824560] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5824.571917] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 5824.571929] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 5824.571935] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 6956.290061] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 6956.296671] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 6963.080560] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 6963.080566] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 6963.080570] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 7613.469241] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 7613.475870] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 7620.201265] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 7620.201278] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 7620.201285] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 8232.762453] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 8232.769065] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 8239.581772] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 8239.581784] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 8239.581792] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [13763.634808] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [13763.641427] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [16955.598953] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [16955.605574] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 lshw:    *-network        description: Wireless interface        product: Centrino Advanced-N 6235        vendor: Intel Corporation        physical id: 0        bus info: pci@0000:03:00.0        logical name: wlan0        version: 24        serial: b4:b6:76:a0:4b:3c        width: 64 bits        clock: 33MHz        capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless        configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-32-generic firmware=18.168.6.1 ip=10.250.169.96 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn        resources: irq:46 memory:f7c00000-f7c01fff iwlist scan: Cell 02 - Address: 24:DE:C6:B0:C7:D9                     Channel:36                     Frequency:5.18 GHz (Channel 36)                     Quality=29/70  Signal level=-81 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=0000004ff3fe419b                     Extra: Last beacon: 27820ms ago                     IE: Unknown: 0009436174436861743278                     IE: Unknown: 01088C129824B048606C                     IE: Unknown: 030124                     IE: IEEE 802.11i/WPA2 Version 1                         Group Cipher : CCMP                         Pairwise Ciphers (1) : CCMP                         Authentication Suites (1) : 802.1x                     IE: Unknown: 2D1ACC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: 3D1624001B000000FF000000000000000000000000000000                     IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00                     IE: Unknown: DD1E00904C33CC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: DD1A00904C3424001B000000FF000000000000000000000000000000           Cell 04 - Address: 24:DE:C6:B0:C3:E9                     Channel:149                     Frequency:5.745 GHz                     Quality=28/70  Signal level=-82 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=000000181f60e19c                     Extra: Last beacon: 28680ms ago                     IE: Unknown: 0009436174436861743278                     IE: Unknown: 01088C129824B048606C                     IE: Unknown: 030195                     IE: Unknown: 050400010000                     IE: IEEE 802.11i/WPA2 Version 1                         Group Cipher : CCMP                         Pairwise Ciphers (1) : CCMP                         Authentication Suites (1) : 802.1x                     IE: Unknown: 2D1ACC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: 3D1695001B000000FF000000000000000000000000000000                     IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00                     IE: Unknown: DD1E00904C33CC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: DD1A00904C3495001B000000FF000000000000000000000000000000                     IE: Unknown: DD07000B8601040817                     IE: Unknown: DD0E000B860103006170313930333032           Cell 09 - Address: 24:DE:C6:B0:C0:29                     Channel:149                     Frequency:5.745 GHz                     Quality=39/70  Signal level=-71 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=00000112fb688ede                     Extra: Last beacon: 27716ms ago ifconfig (while connected): wlan0     Link encap:Ethernet  HWaddr b4:b6:76:a0:4b:3c             inet addr:10.250.16.220  Bcast:10.250.31.255  Mask:255.255.240.0           inet6 addr: fe80::b6b6:76ff:fea0:4b3c/64 Scope:Link           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1           RX packets:230023 errors:0 dropped:0 overruns:0 frame:0           TX packets:130970 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:1000            RX bytes:255999759 (255.9 MB)  TX bytes:16652605 (16.6 MB) iwconfig (while connected): wlan0     IEEE 802.11abgn  ESSID:"CatChat2x"             Mode:Managed  Frequency:5.745 GHz  Access Point: 24:DE:C6:B0:C0:29              Bit Rate=6 Mb/s   Tx-Power=15 dBm              Retry  long limit:7   RTS thr:off   Fragment thr:off           Power Management:off           Link Quality=36/70  Signal level=-74 dBm             Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0           Tx excessive retries:0  Invalid misc:3   Missed beacon:0

    Read the article

  • Nginx Static Content Server Maxing Out?

    - by Harry
    I use nginx to serve the static content for a decently busy website of mine. I have the logging disabled, and 4 worker processes enabled with 5,000 connections per worker (which should yield a max connection limit of 20,000. The server is only operating at about 10% CPU usage and 50% ram, but it's very laggy, and sometimes nginx is so slow to respond to the requests, it times out. For a small number of connections, it's fine, but once any load starts occurring (~2,500 connections), it backs up and bogs down. Is there any other bottlenecks or limits that I might be hitting? This is a FreeBSD server, and all the static files are located locally (not NFS). The NIC is an unmetered gigabit, and it's only using around 75 megabit. Any insight would be appreciated. Thanks.

    Read the article

  • Wireless connection shows up but can't connect to internet with an Intel WiFi Link 5100

    - by Eddy
    I'm using an Asus G50V and I'm completely new to ubuntu. I just installed it and can connect to the internet with a wired connection and through wireless from my windows vista that I installed wubi on, and I can connect to my wireless network, but I can't actually connect to the internet through my wireless network. Thanks in advance. Network controller is an Intel Corporation WiFi Link 5100 according to lspci if that helps Also, the connection somehow started working after I decided to unplug my ethernet cable for the third time and headed upstairs after giving up for the day.. not sure how it happened, but after restarting, the connection stopped working again.. Wifi works on 11.10, but stops working when I upgrade back to 12.04..

    Read the article

  • How can I install wireless drivers without internet?

    - by Ruben
    [Ubuntu 12.04 LTS] I have a HP Pavilion dv6 and I need a Broadcom driver (closed source) to access the internet. However, I need to download that, which I am unable to do because I do not have internet access. My ethernet port has always been broken and I have not been able to access the internet since I installed Ubuntu. I need to find a way for me to install those drivers desperately. I still have Ubuntu on my USB, which for some reason, did have the ability to install that driver (I think it's due to the fact that it already has it somewhere in the files). On my USB Ubuntu, I have that particular driver installed. I was thinking that if one of you knows where drivers are installed, I could locate those files on the USB Ubuntu, then plug in an additional USB to copy them; restart my computer to the harddrive Ubuntu and then install the files from the (additional) USB. I would really appreciate help since to me a computer without internet is useless.

    Read the article

  • fix a broken ubuntu installation from pendrive

    - by interstar
    Something went wrong in the upgrade of my Ubuntu 13.04 to 13.10 The upgrade basically crashed halfway through. On booting I was thrown into a maintainence screen. I found some online instructions for fixing with the package manager ... Which seemed to do a lot of setting up. But then crashed saying package is in a bad inconsistent state. Now I'm in a position where Ubuntu starts again, but goes into a low-res screen and there's no WiFi. I have no Ethernet cable connection but I did download the 13.10 iso on another machine and put it on a pen drive. So I'd like to know there's a way of asking the machine from inside Ubuntu to redo its upgrade from the data on the pendrive rather than WiFi. Is this possible? Cheers Phil

    Read the article

  • Always use one slow connection in preference of a "faster" one

    - by billc.cn
    In Windows, there's this automatic metric thing where the metric is selected according to the declared speed of the link. I now have a gigabit LAN routed to a 2MB DSL service and a HSDPA mobile broadband connection. The former is always chosen for Internet packets even though the latter is actually faster. I tried setting the mobile broadband's interface metric to 1 and raising its priority in the advanced settings of the adapter settings, but this does not seem to affect the metric of the default route. The default route to the Ethernet interface always have a lower metric than the mobile broadband interface. Am I missing something here?

    Read the article

  • building kernel headers (v3.4) breaks wifi (in Ubuntu 12.04.1 LTS)

    - by iphonedev7
    I have dual-booted by Samsung Series 5 Chromebook into Ubuntu using Jay Lee's script/instructions, and then installed the ~500 updates that appear thereafter. Now, I am trying to build my kernel headers in an attempt to enable virtualization so that I can run VirtualBox (I have a VM image on a flashdrive). I followed the instructions here: https://groups.google.com/forum/?fromgroups=#!topic/chromebook-central/PPQFpC7mYzk mainly doing as olofj suggests in his answer, while also making sure to abide by additions/edits made by panZ and algp. However, now that I have done so, my wifi has stopped working, and when I click on the network icon in the top bar, in place of wifi networks there is a grayed-out message that says "no network devices available". I have an Atheros AR9300 Ethernet card (I think thats what you call it). Any help is much needed and appreciated. Any further details necessary to answer the question will be provided as necessary. Thanks!

    Read the article

  • Linksys EA3500 : use WAN port as WAN + LAN possible?

    - by Dough
    I'm waiting for deliver of a Linksys EA3500 router. I was wondering if it was possible to get the WAN port act as normal WAN port (Internet IP) + LAN switch ? My problem is that my Internet box is in a room with NAS and PC, and the router will be in another room with TV, PS3 and PC. The Internet box have a 4 port Gigabit switch so one cable will plug from there to the router's WAN in the other room. The router will get the Internet IP from the Internet box, but will it be possible to have private network through this link too ? I could have a first network between the Internet box and the router, and another network form router and devices but that will do double NAT for nothing... Thanks for reading me and your help !

    Read the article

  • Wired Connection shared with other computers connects then disconnects in 11.10 nm-applet

    - by approbatory
    connecting with shared with other computers connection in NetworkManager. Other computer gets IP but NetworkManager disconnects the shared connection after half a second. This same setup worked perfectly fine in 11.04. Is there any fix, workaround or alternative way to share a connection with another computer over an Ethernet cable. (I can downgrade to 11.04 but I'd rather not ). EDIT: found a workaround The workaround for now is to set IPv6 options to Ignore and then sudo killall dnsmasq. Reconnect and it should work.

    Read the article

  • Changed isp, Ubuntu 13.04 won't connect to the internet

    - by Lori
    I recently moved and changed internet service providers. my ubuntu 13.04 machine is unable to connect to the internet. I need help with the networking settings. The previous isp was Verizon dsl, current a cable company. Both connect via ethernet cable. The cable and router work on a windows machine, but not my ubuntu machine. The cable company doesn't support ubuntu or any linux operating systems. The computer seems to recognize the connection. When I unplug and plug in the cable I get a little window that says disconnected, connected. However, I can't connect to the internet in either Firefox or the Ubuntu software installer (tried this to see if it was a firefox issue, it wasn't). I tried shutting down and restarting, plugging and unplugging cables, etc.

    Read the article

< Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >