Search Results

Search found 2516 results on 101 pages for 'gigabit ethernet'.

Page 58/101 | < Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >

• Wired internet speed is slow in Ubuntu 12.04

  - by RameshKatkam

  I have dual boot Windows 7 and Ubuntu 12.04 on my Dell N4110 laptop. I recently installed Ubuntu 12.04 on my existing windows 7 hard drive. I am experiencing very slow internet speed on Ubuntu(wired connection). But on Windows,internet is really fast. I disabled ipv6 by editing /etc/sysctl.conf No avail. Then i run the following command. sudo ethtool -s eth0 speed 100 duplex full autoneg off No benefit. I am having "Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05)" network card.

  Read the article

• Do I need a wifi card to have internet access?

  - by Sarah

  I am attempting to set up a wireless network on 11.04, freshly download today. The router is on and working. However, I do not have a wifi "card" (which I am assuming is a little USB-type thing that allows internet access, but correct me if I am wrong) and every time I try to type in the MAC address and everything, nothing works. I also get the "firmware missing" error when I scroll over the signal strength, which I have tried looking up but have been unsuccessful with completely understanding it. I guess my main question is do I need another little device to be able to use wifi on my ubuntu? I do have an ethernet cable but another person is using it and I do not want to be tied down to that cable. the problem is that none of the wireless networks show up, however they show up when I go into Windows mode on my laptop. I get an error message at the top saying "firmware missing" which I have tried looking up but still have no straight answer for.

  Read the article

• Configuring bind9 views so I can have DNS services?

  - by Cesar Downs

  I want to configure bind9 using the Ubuntu terminal to have the DNS resolve a local name, not a domain name. For example, if I type in Nicole it will resolve my IP address in a local network fashion. How can I do this, step-by-step please? I've already installed bind9 using: sudo apt-get install bind9 It's fully installed now, I just need some help configuring. Should I be using local views? I am going to do the connection with two laptops probably connected to each other by Ethernet cable or WIFI. One of them is running Ubuntu and the other is running Windows. I not sure if that's part of the problem.

  Read the article

• Seasgate GoFlex NAS + Horrible Speed = Bad Experience

  - by Jon H

  I am having issues with transfer speeds from my desktop PC to my NAS. I have my NAS hooked up to a Gigabit Gateway as well as my Desktop with Cat 5e. I see up to 4.0 MB/Second Transfer Rates, the normal is about 2.5 MB/Seconds. There is 3 Partitions on my NAS, Public, Private, Backup. When I transfer from Private to Public I see the speeds above. If its under the same partition almost instant. I was wondering if the speeds I am seeing is in due to my Computer or the NAS. I was looking into building my own Media Server in due to these horrible speeds. Is their anything I can do in the mean time to speed this up? Motherboard = M3970AM-HP (Angelica) Processor = AMD FX 6100 Ram = 10GB PC3-10600 MB/sec Hard Drive (1) = 1.5TB SATA 3.0GB 5400RPM Hard Drive (2) = 120GB SATA SSD NAS = Seagate 3TB Go Flex Home Connection (1) = 1000 Base T Connection (2) = Wireless N

  Read the article

• 12.04 BCM4312 and aireplay-ng/airodump-ng

  - by Haxornator

  First off, I've read through all of the posts regarding BCM4312 on the forums but haven't been able to get any help. Basically I have a Dell Inspiron 1564 which I've installed 12.04 on and for the most part everything works fine but now that I'm trying to use more in depth utilities such as aireplay and airodump I'm coming across what I believe to be a driver problem thats not allowing compatibility for these programs. Does anyone out there have any suggestions how to resolve this? This is the error I receive: root@Haxornator:~/aircrack/aircrack-ng-1.1# airodump-ng eth2 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth2 <#' Sysfs injection support was not found either.

  Read the article

• Hostapd to connect laptop to Android

  - by Kmegamind

  i am trying to set up my laptop as an access point for my Android to use WiFi, so i knew that ubuntu sets the network as Ad-Hoc which is not discoverable by android, So i tried the method explained here -which i found on many other websites- but when i run hostapd.conf this error appears : nl80211: Failed to set interface wlan0 into AP mode nl80211 driver initialization failed. ELOOP: remaining socket: sock=4 eloop_data=0x8e488f8 user_data=0x8e48ea0 handler=0x807c5e0 ELOOP: remaining socket: sock=6 eloop_data=0x8e4aca8 user_data=(nil) handler=0x8086770 this is how my hostapd.conf looks like : interface=wlan0 driver=nl80211 ssid=Any_SSID_name hw_mode=g channel=1 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_passphrase=Any_password wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP and this is my wireless card info : description: Wireless interface product: BCM43225 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:73:51:f1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=brcmsmac driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:f0300000-f0303fff

  Read the article

• Inside the Raspberry Pi Factory

  - by Jason Fitzpatrick

  Curious where your pint-sized Raspberry Pi came from? You might be surprised to learn it was built, tested, and packaged all in an equally pint-sized factory in South Wales. Nick Heath of Tech Republic takes us on a photo tour of the Raspberry Pi factory with a stop at each stage of production and testing. The photo above shows one of the manual construction steps, the insertion of the large components such as the USB and Ethernet ports. Hit up the link below for the full tour. Raspberry Pi: Inside the Pi Factory [Tech Republic] Our Geek Trivia App for Windows 8 is Now Available Everywhere How To Boot Your Android Phone or Tablet Into Safe Mode HTG Explains: Does Your Android Phone Need an Antivirus?

  Read the article

• Performance problems on RDC to our Terminal-Server Win2008 R2

  - by user40021

  Hello, we have a new win2008-R2 (2x Xeon X5570, 32GB RAM). There I have installed the terminal-server roles, thats all OK. Currently 5 users are working at this server, but all get a very low performance in their remote-desktop session. Sometime it takes 1-2 seconds till the keyboard-inputs will be performed and shown. At the clients I run RDP v 6.1 We have also an older TS-server (based on Win2003 with an Opteron-CPU), there are working about 20 users at the same time. There I do not have the troubles with the inputs at the remote-desktop sessions. Both servers are connected to the same gigabit-switch. Any ideas what could cause the troubles at the Win2008 R2? Many thanks in advance. Regards Chris

  Read the article

• Installing Broadcom Drivers on Ubuntu 12.04

  - by HDInfinity

  I downloaded Ubuntu 12.04 so that I could Dual boot between Ubuntu and Vista. I am currently using a Broadcom 802.11.n Network Adapter for internet, I DON'T have access to an Ethernet connection. Is there a way for me to install the Broadcom drivers for Ubuntu while running Vista, then just install the drivers on Ubuntu from my Vista files. Or put the Drivers on a USB and install from there. There is no way for me to get an internet connection on Ubuntu without the Broadcam drivers.

  Read the article

• Can I increase the link speed of the RAS Server on our MS Win2k3 box?

  - by Ducain

  We are running a Win2K3 Server box, and I'm a remote employee that connects via VPN. I've been frustrated for some time by the connection speed over the VPN (the office HQ has a decent speed and I have a biz class connection here), and decided to do some checking today. This morning, I was dialed in and looked at the networking tab of the task manager, and I see that the adapter for the RAS Server (the box has 4 Gigabit adapters) has a speed that seems far too low. The speed for the RAS Server link hovers between 300 - 600 Kbps. The local connection (and others) all say 1 Gbps. Can I set this to a higher speed? Is this information accurate? Thanks for the input.

  Read the article

• Extremely slow transfer speed ubuntu -> Windows

  - by Hailwood

  I have two laptops, One is running Ubuntu 12.04 (EXT4) the other is running Windows 7 (NTFS). I am copying over 40gb of data (one file) from the Ubuntu laptop to the Windows Laptop. (Browse the shared folder on Ubuntu using Windows copy/paste) But I am getting transfer speeds topping out at ~700kb/s Surely this is not right. I am transferring via wifi on both laptops. My download speeds can reach 7-8mb/s on both laptops, so I know it is not the wifi cards or the router topping out. wlan0 Link encap:Ethernet HWaddr 84:4b:f5:db:b4:85 inet addr:192.168.1.66 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::864b:f5ff:fedb:b485/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11941185 errors:0 dropped:0 overruns:0 frame:0 TX packets:11306693 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10087111370 (10.0 GB) TX bytes:7843524888 (7.8 GB)

  Read the article

• Ubuntu 13.10 install VMware 9.0

  - by user212290

  After I install the VMware workstation 9.0, while when I want open the VM, there come the dialogue "Before you can run VMware, several modules must be complied and loaded into the running kernel CANCEL INSTALL",while I clicked the INSTALL button, nothing happened. When: sudo apt-get install linux-headers-3.11.0-12-generic sudo /usr/bin/vmware-modconfig --icon=vmware-workstation --appname=VMware come: cc1: some warnings being treated as errors make[2]: *** [/tmp/modconfig-T9k19t/vmci-only/linux/driver.o] Error 1 make[2]: *** Waiting for unfinished jobs.... make[1]: *** [_module_/tmp/modconfig-T9k19t/vmci-only] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.11.0-12-generic' make: *** [vmci.ko] Error 2 make: Leaving directory `/tmp/modconfig-T9k19t/vmci-only' Failed to build vmci. Failed to execute the build command. Starting VMware services: Virtual machine monitor done Virtual machine communication interface failed VM communication interface socket family done Blocking file system done Virtual ethernet failed VMware Authentication Daemon done

  Read the article

• Windows file sharing connects over WiFi instead of LAN

  - by zacaj

  I have a laptop and a desktop computer, and I need to sync lots of files to the laptop and back whenever I go on a trip, etc. I've got a LAN cable connected into an extra port on the desktop that I plug into the laptop so I can get gigabit file transfers instead of wireless G. They connect fine. If I do an FTP transfer, for instance, using the LAN IP addresses, it goes at ~40MB/s, as it should. However when I copy files using explorer and native windows file sharing it detects the other computer by name, not IP (eg \\DESKTOP-PC\ instead of \\192.168.0.100\) and always connects to it by its wireless IP address instead of the faster LAN address. Both computers are running Windows 7. I have tried editing the priorities of the adapters in Advanced Settings and putting the LAN adapters above the wifi ones, but this didn't have any effect

  Read the article

• Why do the interfaces show ipv6 address along with ipv4

  - by nixnotwin

  I have manually specified only ipv4 address for my interfaces. But all the interfaces automatically show inet6 address as well. Does it mean that ubuntu starts an ipv6 tunnel by default. If it does, isn't it dangerous, as ipv6 assigns public ips for all LAN clients. I only have a firewall on my NAT router, and my clients, who's interfaces show ipv6 address, do not have firewalls. Here is a screenshot: eth0 Link encap:Ethernet HWaddr 34:dc:47:2e:ad:13 inet6 addr: fe80::28cf:38ff:fb7b:da19/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5783 errors:0 dropped:0 overruns:0 frame:0 TX packets:6098 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:2961324 (2.9 MB) TX bytes:1573757 (1.5 MB) Interrupt:46 Note: For privacy reasons I have modified the HWaddr and inet6 addr values.

  Read the article

• Win 2003 STD network adapter always showing DHCP when in static IP configuration, + it loses the DNS

  - by Darragh

  Hi, I have a server that after the first configuration it was DHCP, now I have added it to our domain and in a static IP, however after a few moments it returns to DHCP but with only some of the IPv4 setting staying the same, It loses DNS for example. I'm not sure what is causing the problem but all I know is this started to happen after I added it to the domain, Would it be a domain policy? or the NIC drivers Spec; Dell M605 Blade server Windows 2003 STD SP1 Intel Xeon Quad core NIC: Dual embedded Broadcom NetXtreme IITM 5708 Gigabit Ethernet NIC w/ TOE

  Read the article

• In 10.10, USB 3.0 PCI Express card recognized by lspci but not lsusb or dmesg. How to fix?

  - by Paul

  Asus N PC, runs 10.10 x86_64 The Asus N comes with 4 usb 2.0 ports, each labelled 2.0 on the case. Attempting to add two usb 3.0 ports to be provided by a generic usb 3.0 pci express card installed in the pci expres slot. The new card says usb 3.0 and has the blue ports. The card is installed into the laptop unpowered, then the laptop is powered on and boots normally. Nothing happens when a USB 3.0 flash drive is inserted into the usb 3.0 port. uname -a Linux drpaulbrewer-N90SV 2.6.35.8 #1 SMP Fri Jan 14 15:54:11 EST 2011 x86_64 GNU/Linux lspci -v 00:00.0 Host bridge: Silicon Integrated Systems [SiS] 671MX Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64 Kernel modules: sis-agp 00:01.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fa000000-fdefffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [f4] Power Management version 2 Capabilities: [70] Subsystem: Silicon Integrated Systems [SiS] PCI-to-PCI bridge Kernel driver in use: pcieport 00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media IO] (rev 01) Flags: bus master, medium devsel, latency 0 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev 01) (prog-if 80 [Master]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 128 I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at ffe0 [size=16] Capabilities: [58] Power Management version 2 Kernel driver in use: pata_sis 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 20 Memory at f9fff000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 21 Memory at f9ffe000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller (prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 22 Memory at f9ffd000 (32-bit, non-prefetchable) [size=4K] Capabilities: [50] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter (rev 02) Subsystem: ASUSTeK Computer Inc. Device 11f5 Flags: bus master, medium devsel, latency 0, IRQ 19 Memory at f9ffcc00 (32-bit, non-prefetchable) [size=128] I/O ports at cc00 [size=128] Capabilities: [40] Power Management version 2 Kernel driver in use: sis190 Kernel modules: sis190 00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA Controller / IDE mode (rev 03) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 17 I/O ports at c800 [size=8] I/O ports at c400 [size=4] I/O ports at c000 [size=8] I/O ports at bc00 [size=4] I/O ports at b800 [size=16] I/O ports at b400 [size=128] Capabilities: [58] Power Management version 2 Kernel driver in use: sata_sis Kernel modules: sata_sis 00:06.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Memory behind bridge: fdf00000-fdffffff Capabilities: [b0] Subsystem: Silicon Integrated Systems [SiS] Device 0004 Capabilities: [c0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [f4] Power Management version 2 Kernel driver in use: pcieport 00:07.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=06, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fe000000-febfffff Prefetchable memory behind bridge: 00000000f6000000-00000000f8ffffff Capabilities: [b0] Subsystem: Silicon Integrated Systems [SiS] Device 0004 Capabilities: [c0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [f4] Power Management version 2 Kernel driver in use: pcieport 00:0f.0 Audio device: Silicon Integrated Systems [SiS] Azalia Audio Controller Subsystem: ASUSTeK Computer Inc. Device 17b3 Flags: bus master, medium devsel, latency 0, IRQ 18 Memory at f9ff4000 (32-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 01:00.0 VGA compatible controller: nVidia Corporation G96 [GeForce GT 130M] (rev a1) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device 2021 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fc000000 (32-bit, non-prefetchable) [size=16M] Memory at d0000000 (64-bit, prefetchable) [size=256M] Memory at fa000000 (64-bit, non-prefetchable) [size=32M] I/O ports at dc00 [size=128] [virtual] Expansion ROM at fde80000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Kernel driver in use: nvidia Kernel modules: nvidia-current, nouveau, nvidiafb 02:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Device 1a3b:1067 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fdff0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Kernel driver in use: ath9k Kernel modules: ath9k 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at febfe000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable- Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 lsusb Bus 003 Device 002: ID 0b05:1751 ASUSTek Computer, Inc. BT-253 Bluetooth Adapter Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 004: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 001 Device 002: ID 04f2:b071 Chicony Electronics Co., Ltd 2.0M UVC Webcam / CNF7129 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub dmesg trying to post dmesg exceeded the stackexchange posting limit of 30K... but nothing there is usb 3.0

  Read the article

• Wifi networks will not show up!

  - by Kcahmadi

  I'm running Ubuntu 14.04 on an old '08 macbook. I've gone to system settingsSoftware & UpdatesAdditional Drivers and enabled the wireless driver. But when I click the wifi icon on the top toolbar no networks show up. When running lshw it clearly shows my wireless card under Network controller and it says the driver is installed. However, nm-tool only shows ethernet. And rfkill only shows bluetooth. What can I do?

  Read the article

• Install a Mirror without downloading all the packages in the official repository

  - by Sam

  I first gonna explain the situation : ( The two PCs are running Ubuntu 12.04 ) I have a Laptop which is connected to a wifi connection, and a Desktop which can not be connected to Internet ( the modem is too far from it ), and i want to install some software to the last one. ( the two PCs are connected with an Ethernet cable ) I've already searched for a solution, but all i found was the use of some softwares that should have been already installed on the "Internet-less PC". ( Keryx, APTonCD ... ) What I want to do is to create a mirror in my laptop which contain the packages i have in this one ( situated in /var/cache/apt/archive ) and i don't want to download all the packages from the official repository, I don't need them. Can someone tell me if this is possible ? Thank you.

  Read the article

• Two Wifi Icons in Panel

  - by Alex

  I have the exact problem in 13.10 as this user Two Wifi indicators in panel. Here are some screenshots: Here are some screenshots from another user: http://ubuntuforums.org/showthread.php?t=2183020&p=12825563 ifconfig and iwconfig outputs $ ifconfig lo Link encap:Local Loopback inet addr:XXXXXX Mask:XXXXXXX inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2243 errors:0 dropped:0 overruns:0 frame:0 TX packets:2243 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:209889 (209.8 KB) TX bytes:209889 (209.8 KB) wlan0 Link encap:Ethernet HWaddr XXXXXXXXX inet addr:XXXXXX Bcast:XXXXXXXX Mask:XXXXXXX inet6 addr: XXXXXXX Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5925 errors:0 dropped:0 overruns:0 frame:0 TX packets:3361 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2951818 (2.9 MB) TX bytes:630579 (630.5 KB) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"XXXXX" Mode:Managed Frequency:2.437 GHz Access Point: XXXXXXXX Bit Rate=72.2 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:153 Invalid misc:472 Missed beacon:0

  Read the article

• Why dhclient is still running when I choose static IP?

  - by user276851

  I modify dhcp to static in /etc/network/interfaces (like below). # The primary network interface auto eth0 iface eth0 inet static netmask 255.255.0.0 address 10.10.130.128 gateway 10.10.1.1 Then restart the interface. $ sudo ifdown eth0; sudo ifup eth0 ... $ ifconfig eth0 Link encap:Ethernet inet addr:10.10.130.128 Bcast:10.10.255.255 Mask:255.255.0.0 So the new address kicks in. But DHCP is still there? $ ps aux | grep dhc root ... dhclient3 -e IF_METRIC=100 -pf /var/run/dhclient.eth0.pid -lf /var/lib/dhcp/dhclient.eth0.leases -1 eth0 Is that normal? If not, how to restart interface in static IP while stop DHCP at the same time? Thanks a lot.

  Read the article

• Install a Mirror without downloading all packages from official repository

  - by Sam

  I first gonna explain the situation: I have a Laptop which is connected to a wifi connection, and a Desktop which can not be connected to Internet (the modem is too far from it), and i want to install some software on the last one. (The two PCs are running Ubuntu 12.04, and are connected with an Ethernet cable) I've already searched for a solution, but all I've found was the use of some softwares that should have been already installed on the "Internet-less PC". ( Keryx, APTonCD ... ) What I want to do is to create a mirror in my laptop which contain the packages i have in this one ( situated in /var/cache/apt/archive ) and i don't want to download all the packages from the official repository, I actually don't need them. Can someone tell me if it is possible to do that ? Thanks,

  Read the article

• Slow wifi after upgrading kubuntu 13.04 to 13.10

  - by RedCow22

  After upgrading from kubuntu 13.04 to 13.10 suddenly my wifi connection is very slow. Ping times are varying from 200 up to 1500 ms to www.google.nl. When I connect my ethernet cable they drop to normal times like 8 or 9 ms. Anyone experiencing the same problem or know a solution I can try? During the upgrade process a few times they asked whether I wanted to keep or replace some kind of configuration file. I'm not sure anymore which file it was, but maybe this has something to do with it. Before the upgrade both wired and wireless connection worked perfect.

  Read the article

• Laptop works fine with ac adapter, hangs after login screen using battery

  - by tavoton

  I did an Ubuntu 10.10 Desktop Edition clean install (amd64 version) on a notebook Medion Akoya E1311. With AC adapter everything works fine, but using battery, it hangs after login screen. I can type login, password too, and I can press login button. But then I can see mouse cursor and lower task bar, not upper, and nothing works. The only thing I can do is login on a terminal with ctrl+alt+F1, this is ok. Nothing seems alive on Gnome except mouse cursor. The only thing I did after Ubuntu fresh install was donwloading driver for RTL8191SE from Realtek web, because WiFi didn't work, now works fine, with ac adapter of course. Hardware is a Notebook Medion Akoya E1311 AMD Sempron 210U 1 GB DDR2 ATI RS690M (Radeon X1200 Series) Western Digital 160GB wireless RTL8191SEvB ethernet RTL8101E/RTL8102E

  Read the article

• why is there so much variance in prices for a 2-bay NAS?

  - by jcollum

  I'm considering buying a 2bay NAS for media storage. I'm perplexed by the variety of prices. They go from about $115 to $1200. The only thing I could see that differentiated the high end drive was encryption and a dual gigabit ethernet port. I don't understand how that can add up to $800+ dollars. Clearly I should know why there's this price variance before considering buying a 2 Bay NAS. Newegg link to 2 Bay NAS Should I move this question to serverfault?

  Read the article

• Ubuntu 12.04 server froze during the first boot after it was installed.

  - by user69021

  I installed Ubuntu server 12.04 to my new server and it failed on the first boot. It just stopped and I can't proceed any further. Server's specifications: Dell PowerEdge T620 CPU : Xeon E5-2665 2.4G x 2 RAM : 8GB RDIMM, 1333MHz x 12 HDD : 3TB Near Line SAS 7.2K x 8 RAID controller : PERC H710 GPU : NVIDIA Tesla C2075 x 4 I have a screenshot of the screen it stopped on but I cannot attach it because my privilege level is currently too low. ![freeze on boot][1] Here are the last messages while booting. [5.048743] Freeing unused kernel memory : 920k freed [5.049046] Write protecting the kernel read-only data : 12288k [5.052973] Freeing unused kernel memory : 1608k freed [5.056132] Freeing unused kernel memory : 1196k freed Loading, please wait... [5.070236] udevd[218]: starting version 175 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. [5.089030] megasas: 00.00.06.12-rc1 Wed. Oct. 5 17:00:00 PDT 2011 [5.089518] megasas: 0x1000:0x005b:0x1028:0x1f35: bus 1:slot 0:func 0 [5.089739] megaraid_sas 0000:01:00.0: PCI INT A -> GSI 34 (level, low) -> IRQ 34 [5.089937] megasas: FW now in Ready state [5.090427] dca service started, version 1.12.1 [5.091463] Intel(R) Gigabit Ethernet Network Driver - version 3.2.10-k [5.091578] Copyright (c) 2007-2011 Intel Corporation. [5.091712] igb 0000:06:00.0: PCI INT A -> GSI 16 (level,low) -> IRQ 16 [5.111090] megasas:IOC Init cmd success [5.123124] usb 1-1:new high-speed USB device number 2 using ehci_hcd What can I do about this?

  Read the article

< Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >