Search Results

Search found 3084 results on 124 pages for 'lan'.

Page 57/124 | < Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >

• Acer Aspire One 722 broadcom 4313 wifi

  - by Colin Matheson

  I had an Acer Aspire One 722 with the Atheros Wifi card and it worked fine on 11.04. So we bought 200 of them for our school. However these all came with the Broadcom BCM4313 wireless card and there are issues. It is using the brcmsmac driver and they connect initially. However after a time (sometimes just a few webpages) some of them lose connection. However, they still have an IP and network-manager says they are connected, but no pages load and you can't ping anything on the LAN or internet. A disconnect/reconnect can fix it, but sometimes a restart is required. It happens frequently so is a major issue. Lots of broadcom drivers are blacklisted: bcm43xx, b43, brcm80211. Any ideas or experiences with the broadcom4313 card? Please save these computers from a Windows fate!

  Read the article

• My wireless is hard-blocked

  - by Cristian

  I'm new to linux and i am having trouble getting my wireless to work I've found the following things Wireless LAN Soft blocked: no Hard blocked: yes and : *-network DISABLED description: Wireless interface product: RT3090 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 6c:62:6d:19:38:b9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.2.0-25-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:fdfe0000-fdfefff Can you please tell me what to do?

  Read the article

• Ubuntu 12.10, Wireless not working

  - by Karthik

  My Laptop is Acer 5742G with "Npilfy 802.11 wireless". I have both windows 7 and Ubuntu 12.10 Earlier when I had Ubuntu 12.04, the wireless was working fine, but after installing 12.10 wireless is not working at all, although it is still working in windows. I am not able to see "Wireless Networks" in the Network Manager nor in the Network Settings. This was the output I got for rfkill 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: acer-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no This is a snapshot of my Additional Drivers settings. As you can see, the required driver for wireless is installed.

  Read the article

• Can't connect to wireless on Lubuntu

  - by migwke

  I have a CISCO 802.11b WIFI Mini PCI LAN card in my IBM ThinkPad T30 laptop. Is this wireless card compatible with Lubuntu? I have Lubuntu installed and it just won't connect. It keeps saying that it is trying to configure then it says that it is connected but it does not work. I know that the wireless network is working correctly because I can connect to it with all my other devices and it works on this very same laptop when I am running Windows. I added the following commands to blacklist.conf, but still no luck blacklist padlock_aes blacklist geode_aes

  Read the article

• Multiplayer Game Listen Servers: Ensuring Integrity

  - by Ankit Soni

  I'm making a simple multiplayer game of Tic Tac Toe in Python using Bridge (its an RPC service built over a message queue - RabbitMQ) and I'd like to structure it so that the client and the server are just one file. When a user runs the game, he is offered a choice to either create a game or join an existing game. So when a user creates a game, the program will create the game and also join him as a player to the game. This is basically a listen server (as opposed to a dedicated server) - a familiar concept in multiplayer games. I came across a really interesting question while trying to make this - how can I ensure that the player hosting the game doesn't tamper with it (or atleast make it difficult)? The player hosting the game has access to the array used to store the board etc., and these must be stored in the process' virtual memory, so it seems like this is impossible. On the other hand, many multiplayer games use this model for LAN games.

  Read the article

• use ubuntu notebook as second monitor for fedora desktop

  - by YumTum

  I was wondering if there is a possibility to use my netbook with ubuntu 12.04 as a second monitor for my fedora desktop, because its keyboard is broken but everything else is running just fine. I already read about x2x, but I hope there is a more direct way to do this (I mean not over the WLAN but e.g. via LAN etc... ). Would it be possible to directly use the monitor without even running the laptop? For example through an VGA adapter? Thanks for your replies!

  Read the article

• How do I fix DNS resolving which doesn't work after upgrading to Ubuntu 13.10 (Saucy)

  - by Witek

  After upgrade to 13.10 my DNS resolving fails. It seams the DNS servers which I get by DHCP (LAN) are not used. I could temporary solve the problem by adding nameserver 8.8.8.8 to /etc/resolv.conf. But then the intranet hosts still can not be resolved. When clicking on the Connection Information menu item on the network indicator, the Primary DNS and the Secondary DNS are set correctly. But my computer seams not to use them. So my questions: What should I put into resolv.conf, if anything? How to find out, which name servers my computer is querying? Where to look next, to find out, why name servers received by DHCP are not used?

  Read the article

• Microsoft sort la version finale de son application Tag, qui permet aux smartphones de lire des code

  Microsoft sort la version finale de son application Tag, qui permet aux smartphones de lire des code-barres La technologie de Microsoft permettant de lire les codes-barres pour mobiles, vient d'en terminer avec la phase de bêta testing. Une version finale de Tag est désormais disponible au téléchargement, après 18 mois de développement. Son principe n'est pas nouveau : des code-barres présents à divers endroits (magazines, panneaux d'affichage, etc.) sont scannés par l'appareil photo d'un smartphone puis décodés grâce à un logiciel spécifique (gratuit et compatible avec Android, BlackBerry, iPhone, Symbian, PalmOS et, bien sur, Windows Mobile). Lorsque le Tag est déchiffré, la commande qu'il contient est lancée : lan...

  Read the article

• Multiplayer game communication framework for mac/ios

  - by ishaq

  (Cross post from stackoverflow) I am creating a multiplayer 2D game for Mac and iOS devices. I'll be using cocso2d for graphics/game engine, however I am largely blank on what to use for multiplayer communication. Please note that I cannot use central severs e.g. SmartFox, RedDwarf, etc since I want the players to "host" games for others and be able to play it on their LAN, VPN or my own servers. Any pointers? I checked lidgren but it's for .NET only and hence not an option for me. EDIT: just in case it wasn't clear, the messaging has to be real time hence it's probably going to be over UDP

  Read the article

• Direct X-forwarding

  - by Sean Houlihane

  I'm struggling to set up X-forwarding between 2 different machines on my local network and my ubuntu desktop. I'm able to connect using ssh x-forwarding one one machine, but the other machine (a Qnap TS-219P II) seems to have a less functional build of SSH on it, and I'd rather use a simpler approach. I've set $DISPLAY, and done 'xauth list $DISPLAY' on the desktop, then 'xauth add ' on the remote machine. From the remote machine, I just get xterm xterm Xt error: Can't open display: 192.168.0.4:0.0 Now, oddly, if I connect via ssh -X, there is a different magic cookie for the tunnelled port (but neither seems to work). I'm wondering if there is a port which needs to be enabled to permit X connections from the LAN? If so, how? The proper solution might be to re-build all the packages which are preventing X-forwarding from working on my QNAP machine, but lets assume for the purposes of this question that I've tried building enough packages on that architecture already and want to run X without the overhead of encryption.

  Read the article

• Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to get it to work?

  - by zewone

  I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686  Any help much appreciated... Thanks, Philippe 31-10-2012 ... I have some more updates. When I do the following command it does see my Wifi router... So even if it is still disabled... the card seems to work and see the router (ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E") See below: sudo iwlist wlan1 scanning wlan1 Scan completed : Cell 01 - Address: 00:19:70:8F:B0:EA Channel:10 Frequency:2.457 GHz (Channel 10) Quality=51/70 Signal level=-59 dBm Encryption key:on ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000025dbf2188 Extra: Last beacon: 108ms ago IE: Unknown: 002035373931424332362D434539432D313144312D393742462D3030303046383145 IE: Unknown: 010882848B960C121824 IE: Unknown: 03010A IE: Unknown: 0706424520010D14 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101030003A4000027A4000042435E0062322F00 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000

  Read the article

• Is there a taskbar applet to show the status of a remote host?

  - by Mathew

  At the end of the day I would like to be able to copy files to my home PC just in case I feel inspired to work on them in the evening. But I only want to do this if the PC is on already. (I can remote wake-on-lan the PC but I don't want to always be doing that). I would like some taskbar applet that shows the status of the PC and whether I can ssh into it or not. Obviously it would also be interesting to have an idea as to how long it is on for whilst I am at work as that gives a good indication of whether anyone is in or not. However being able to unobtrusively copy files to the remote machine is the main objective. Perhaps another approach is to run rsync on cron and if the remote host is not up then I guess it will fail. Is that correct? If anyone else has ideas on how to best sync a work and home PC then please do tell.

  Read the article

• First languages with generic programming support

  - by oluies

  Which was the first language with generic programming support, and what was the first major staticly typed language (widely used) with generics support. Generics implement the concept of parameterized types to allow for multiple types. The term generic means "pertaining to or appropriate to large groups of classes." I have seen the following mentions of "first": First-order parametric polymorphism is now a standard element of statically typed programming languages. Starting with System F [20,42] and functional programming lan- guages, the constructs have found their way into mainstream languages such as Java and C#. In these languages, first-order parametric polymorphism is usually called generics. From "Generics of a Higher Kind", Adriaan Moors, Frank Piessens, and Martin Odersky Generic programming is a style of computer programming in which algorithms are written in terms of to-be-specified-later types that are then instantiated when needed for specific types provided as parameters. This approach, pioneered by Ada in 1983 From Wikipedia Generic Programming

  Read the article

• Intel Centrino Wireless-N 1000 Again ! Ubuntu 13.04 x64

  - by vafa

  First I have to say that I tried everything written about this concept. The problem is that it stops working randomly in 3 main forms : 1 - sometimes it disconnect from wireless network and reconnect automatically 2 - sometimes it disconnect and wont connect no matter what (needs reboot) 3 - some times it's still connected but cannot ping or surf or whatever. I already tried disabling N mod using these commands : sudo modprobe -r iwlwifi modprobe iwlwifi 11n_disable=1 (or 0, whatever) it didn't help . these are the results of lspci, sudo lshw -C network, ifconfig, iwconfig, rfkill list when it disconnected and didn't connect till reboot : ifconfig : eth0 Link encap:Ethernet HWaddr c8:0a:a9:34:65:77 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1563213476557380 errors:9379306629148050 dropped:3126435543049350 overruns:1563217771524675 frame:7816088857623375 TX packets:1563217771524675 errors:6252871086098700 dropped:0 overruns:1563217771524675 carrier:3126435543049350 collisions:7816088857623375 txqueuelen:1000 RX bytes:1563217771524675 (1.5 PB) TX bytes:1563217771524675 (1.5 PB) ham0 Link encap:Ethernet HWaddr 7a:79:19:a5:e4:93 inet addr:25.165.228.147 Bcast:25.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:19ff:fea5:e493/64 Scope:Link inet6 addr: 2620:9b::19a5:e493/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:7743 errors:0 dropped:0 overruns:0 frame:0 TX packets:1250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:665642 (665.6 KB) TX bytes:204056 (204.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:41138 errors:0 dropped:0 overruns:0 frame:0 TX packets:41138 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6420962 (6.4 MB) TX bytes:6420962 (6.4 MB) wlan0 Link encap:Ethernet HWaddr 00:1e:64:45:fb:70 inet6 addr: fe80::21e:64ff:fe45:fb70/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:286999 errors:0 dropped:0 overruns:0 frame:0 TX packets:226966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:324386887 (324.3 MB) TX bytes:30674804 (30.6 MB) iwconfig : ham0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off sudo lshw -C network: *-network description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:45:fb:70 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-30-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:46 memory:c0400000-c0401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: c0 serial: c8:0a:a9:34:65:77 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:c0900000-c093ffff ioport:5000(size=128) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:19:a5:e4:93 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full ip=25.165.228.147 link=yes multicast=yes port=twisted pair speed=10Mbit/s lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: NVIDIA Corporation G98M [GeForce G 105M] (rev a1) 07:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak] 09:00.0 Ethernet controller: Qualcomm Atheros AR8131 Gigabit Ethernet (rev c0) rfkill list : 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 9: phy0: Wireless LAN Soft blocked: no Hard blocked: no any help will be REALLLYYYY appreciated

  Read the article

• slow speed transfering files to a local network device

  - by F. Ariel Jung

  I'm having troubles copying files from my pc(ubuntu 13.04 64 bits) to a Media Center(WDTV Live: with an SATA2 HDD attached) through the local network. the speed is to slow, it's up to 2.0 MB/s image: http://s11.postimg.org/g1nuai92b/Captura_de_pantalla_de_2013_06_24_07_46_55.png (I don't use image tag because it is a big image) my PC has a wifi network card Tp Link TL-WN951N and it is connected to a TP Link TL-WDR3500 router via wifi, and the WDTV Live is connected via LAN here is a iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TL-WDR3500" Mode:Managed Frequency:2.462 GHz Access Point: A0:F3:C1:6C:3B:F1 Bit Rate=39 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:33521 Invalid misc:2245290 Missed beacon:0 if more data is required I'll post it as needed. I can't figure this out, needed help. please

  Read the article

• How do I get rid of the drive mount confirmation question for sshFS on boot?

  - by Dave M G

  With help from this site, I was able to set up an SSHFS connection between two computers on my LAN so that one auto mounts on the other at boot time. Everything works, but there is this annoying confirmation that comes up whenever I boot: An error occurred while mounting /home/dave/Mythbuntu. Press S to skip mounting or M or Manual recovery If I press S, then booting continues, and my drive is mounted as hoped, so it seems like even though I "skipped" it, maybe it tried again and succeeded later in the boot process. I followed the instructions here to set up "if up / if down" scripts, and here is my current /etc/fstab: sshfs#[email protected]:/home/mythbuntu /home/dave/Mythbuntu fuse auto,users,exec,uid=1000,gid=1000,allow_other,reconnect,transform_symlinks,BatchMode=yes 0 0 Although the mounting is working, this step of having to press S every time I boot is obviously kind of a hassle. How do I configure my computer so I don't have to do that, and so that my other computer will still automount?

  Read the article

• Wireless not working with an Atheros AR9285

  - by Neeraj

  I recently installed Ubuntu 12.04 and found my wireless card is not detected by OS. I tired to detect it by network manager but still it is not get output of the required command: toor@Linux:~$ sudo lshw -class network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:9e:22:4d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=124.123.227.84 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:44 memory:f2400000-f243ffff ioport:2000(size=128) *-network UNCLAIMED description: Network controller product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f2500000-f250ffff and toor@Linux:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: yes Hard blocked: no Please let me know what more info is required to resolve it.

  Read the article

• Iptables Issue can't SSH Remote Machines

  - by Lonston

  I want to SSH to 192.168.1.15 Server from my machine, my ip was 192.168.1.99 Source Destination was UP, with IP 192.168.1.15. This is LAN Network there are 30 Machine's Connected to the network and working fine, I'm Playing around the local machine's cos i need to apply the same rules in Production VPS I have applied the below iptables in my machine 192.168.1.99, Now i can't receive any packets from Outside and i can't send any packets Outside, While applying the Below Chain iptables -P INPUT DROP iptables -P OUTPUT DROP iptables -P FORWARD DROP After the above CHAIN i have added the Below rules and it want to allow ssh from machine to 192.168.1.15 to access the 192.164.1.15 but still i can't access 192.168.1.15 iptables -A INPUT -p tcp -i eth0 --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -o eth0 --sport 22 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --sport 22 -m state --state ESTABLISHED -j ACCEPT Any one Please Check Weather my Rules are Wrigt. Still i can't access the machine 15

  Read the article

• Is it possible to get a Proxy Authentication Dialog with Ubuntu Server?

  - by Johnny Bigoode

  I've got a VM Virtual Box with Ubuntu Server. I'set the http_proxy variable using export http_proxy="http://1234:linux@proxy:8080" The problem is that Ubuntu will constantly try to connect to the internet, even when I'm not logged in my company's account, so everyday I need to reset my password since Ubuntu will constantly try to access the internet. Also, it's always a problem when I need to authenticate the proxy with a different user/password. Can't I just set it to make a small prompt when it tries to connect to the proxy and fails? Like Firefox, Chrome and every app I have installed with Windows 7? I get this small dialog box that asks for a username and password when it can't access the internet. The Ubuntu Server doesn't need constant internet connection, specially since it's only online for tests over LAN.

  Read the article

• Internet connection randomly drops out

  - by Dr_Bunsen

  Since a week or 2, I have this random network failures. No error pops up, the system says it's still connected to the internet(wifi and wired). The problem is, I can't connect to anything, even a ping google.com gives no feedback. And after many network-manager resets it will work again, for just a minute, and drop out again. I noticed that the /etc/resolv.conf contains this line: nameserver 127.0.0.1 I left out the "Do not edit" stuff, and after it worked for a second, this line is added: search lan When I change the nameserver to 8.8.8.8, I am still able to connect to anywhere. Does anyone got a clue what is happening here? I will provide any information asked. Thanks in advance p.s. I run Ubuntu 13.04 since lastnight(24-06-2013)

  Read the article

• Can't print, CUPS package corrupted and hangs on re-install

  - by Little Bobby Tables

  When I upgraded to Ubuntu 10.4 (Maverick), the upgrade process got stuck on the post-installation of the CUPS package. I had to kill processes and run several forced updates before I could finally get regular updated. Ever since I can't print - The printed file gets messed up and crashes the printer. I also can't re-install CUPS, as each time the installation hangs and I have to kill it before it completes. I tried to find a workaround for this problem, but in vain. Does anyone know how to bypass this? Or at least why can the post-installation hang, and how to re-install a problematic package? Some system specs and other hints: Dell D630 laptop running Ubuntu 10.4, Gnome desktop, standard LAN network, printing to an LPD server. Everything worked fine on 9.10. Also, the printed files themselves are not corrupted. The problem does not seem to be Evince-specific, but common to all printouts.

  Read the article

• Why do the interfaces show ipv6 address along with ipv4

  - by nixnotwin

  I have manually specified only ipv4 address for my interfaces. But all the interfaces automatically show inet6 address as well. Does it mean that ubuntu starts an ipv6 tunnel by default. If it does, isn't it dangerous, as ipv6 assigns public ips for all LAN clients. I only have a firewall on my NAT router, and my clients, who's interfaces show ipv6 address, do not have firewalls. Here is a screenshot: eth0 Link encap:Ethernet HWaddr 34:dc:47:2e:ad:13 inet6 addr: fe80::28cf:38ff:fb7b:da19/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5783 errors:0 dropped:0 overruns:0 frame:0 TX packets:6098 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:2961324 (2.9 MB) TX bytes:1573757 (1.5 MB) Interrupt:46 Note: For privacy reasons I have modified the HWaddr and inet6 addr values.

  Read the article

• How do I get rid of this drive mount confirmation question when booting the computer?

  - by Dave M G

  With help from this site, I was able to set up an SSHFS connection between two computers on my LAN so that one auto mounts on the other at boot time. Everything works, but there is this annoying confirmation that comes up whenever I boot: An error occurred while mounting /home/dave/Mythbuntu. Press S to skip mounting or M or Manual recovery If I press S, then booting continues, and my drive is mounted as hoped, so it seems like even though I "skipped" it, maybe it tried again and succeeded later in the boot process. I followed the instructions here to set up "if up / if down" scripts, and here is my current /etc/fstab: sshfs#[email protected]:/home/mythbuntu /home/dave/Mythbuntu fuse auto,users,exec,uid=1000,gid=1000,allow_other,reconnect,transform_symlinks,BatchMode=yes 0 0 Although the mounting is working, this step of having to press S every time I boot is obviously kind of a hassle. How do I configure my computer so I don't have to do that, and so that my other computer will still automount?

  Read the article

• UFW firewall still blocking SMB despite adding rules

  - by nLinked

  I have an Ubuntu PC with ufw firewall (GUI version). I have added the preset Samba service, in and out, and even tried adding the ports manually (135-139, 445, UDP and TCP, in and out), but it still blocks samba. I am trying to access a share on another PC on my LAN. If I disable ufw, it works fine. It must be still blocking something and I can't figure it out. Any ideas? I'm on Ubuntu 11.04 beta 2.

  Read the article

• Changes to 'resolveconf' discarded when connecting to a new network

  - by sudheer

  I have upgraded to 12.10 from 12.04 recently and I am having issues with connecting to the Internet. I got an IP address and am able to ping other LAN IPs in the local network but I am unable to connect to the Internet and am even unable to ping www.google.com from a terminal. Somehow making changes in /etc/resolv.conf and restarting resolvconf service and rebooting works but I need to do this every time I connect to a new network. How do I make these changes permanent? Can someone suggest a solution to this issue?

  Read the article

< Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >