Search Results

Search found 17984 results on 720 pages for 'log shipping'.

Page 574/720 | < Previous Page | 570 571 572 573 574 575 576 577 578 579 580 581  | Next Page >

• How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

  - by Todd V. Rovito

  I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

  Read the article

• Converting An Older VMWare Image to ESXi

  - by Bart Silverstrim

  I have just installed VMWare ESXi and imported one physical machine without issue and one virtual machine, from an older version of VMWare Server on a Linux system, to it without issue. But I have another machine (Windows XP), virtual running on the VMWare Server, that I can't get the Converter to work with. Converter runs, says everything is fine, but when I go to the ESXi VSphere manager and hit the button to power up that vm, the console stays black with a blinking cursor and the processor for that VM spikes 100% and stays there. An event log item in VSphere warns something about activation issues with Windows. Has anyone else run into this issue before? Is it something with the disk controller? I copied the folder with the VM directly to the storage drive on ESXi hoping to create a new machine and point the data store to that folder or at least that drive image; nope, something about not using an IDE controller (must be something with the older format). In short, converter is doing something that particular machine doesn't like, and I can't find a way to simply open that hard disk image or convert it unless someone else has seen this. I try attaching a bootable CD image for disk repair to see if it can check the hard drive but I can't seem to get the console to boot from it...either too slow on the button or it just isn't able to easily boot from a virtual drive image (.iso). Any suggestions or help?

  Read the article

• Why is OpenSSH not using the user specified in ssh_config?

  - by Jordan Evens

  I'm using OpenSSH from a Windows machine to connect to a Linux Mint 9 box. My Windows user name doesn't match the ssh target's user name, so I'm trying to specify the user to use for login using ssh_config. I know OpenSSH can see the ssh_config file since I'm specifying the identify file in it. The section specific to the host in ssh_config is: Host hostname HostName hostname IdentityFile ~/.ssh/id_dsa User username Compression yes If I do ssh username@hostname it works. Trying using ssh_config only gives: F:\>ssh -v hostname OpenSSH_5.6p1, OpenSSL 0.9.8o 01 Jun 2010 debug1: Connecting to hostname [XX.XX.XX.XX] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_rsa type -1 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_rsa-cert type -1 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_dsa type 2 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3p1 Debia n-3ubuntu5 debug1: match: OpenSSH_5.3p1 Debian-3ubuntu5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'hostname' is known and matches the RSA host key. debug1: Found key in /cygdrive/f/progs/OpenSSH/home/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /cygdrive/f/progs/OpenSSH/home/.ssh/id_rsa debug1: Offering DSA public key: /cygdrive/f/progs/OpenSSH/home/.ssh/id_dsa debug1: Authentications that can continue: publickey debug1: No more authentication methods to try. Permission denied (publickey). I was under the impression that (as outlined in this question: How to make ssh log in as the right user?) specifying User username in ssh_config should work. Why isn't OpenSSH using the username specified in ssh_config?

  Read the article

• 403.4 won't redirect in IE7

  - by Jeremy Morgan

  I have a secured folder that requires SSL. I have set it up in IIS(6) to require SSL. We don't want the visitors to be greeted with the "must be secure connection" error, so I have modified the 403.4 error page to contain the following: function redirectToHttps() { var httpURL = window.location.hostname+window.location.pathname; var httpsURL = "https://" + httpURL ; window.location = httpsURL ; } redirectToHttps(); And this solution works great for every browser, but IE7. On any other browser, if you type in http://www.mysite.com/securedfolder it will automatically redirect you to https://www.mysite.com/securedfolder with no message or anything (the intended action). But in Internet Explorer 7 ONLY it will bring up a page that says The website declined to show this webpage Most Likely Causes: This website requires you to log in This is something we don't want of course. I have verified that javascript is enabled, and the security settings have no effect, even when I set them to the lowest level I get the same error. I'm wondering, has anyone else seen this before?

  Read the article

• Firefox crash on first load on Ubuntu Linux on older Dell Laptop

  - by Ira Baxter

  I've had a Dell Latitude laptop since about 2000 without managing to destroy it. A month ago the Windows 2000 system on it did something stupid to its file system and Windows was completely lost. No point in reinstalling Windows 2000, so I installed an Ubuntu Linux on the laptop. Everything seems normal (installed, rebooted, I can log in, run GnuChess, poke about). ... but ... when I attempt to launch Firefox from the top bar menu icon, I get a bunch of disk activity, the whirling cursor icon goes round a bit and then everything stops: disk, icon, mouse. Literally nothing happens for 5 minutes. Ubuntu is dead, as far as I can tell. A reboot, and I can repeat this reliably. So on the face of it, everything works but Firefox. That seems really strange. The only odd thing about this system when Firefox is booting is that while it has an Ethernet port (that worked fine under Windows), it isn't actually plugged into an Ethernet. As this is the first Firefox boot since the Ubuntu install, maybe Firefox mishandles Internet access? Why would that crash Ubuntu? (I need to go try the obvious experiment of plugging it in).

  Read the article

• Office 2007 constantly crashes, logged as Event ID 1000

  - by Nori

  I have a user, who despite my best efforts, is having constant Office 2007 crashes. I've tried deleting their profile and setting it up again, repairing office, uninstalling completely and then reinstalling, and swapping out memory sticks. One event log error I keep getting is the following: (note all the Office errors are event id 1000) Faulting application name: OUTLOOK.EXE, version: 12.0.6539.5000, time stamp: 0x4c12486d Faulting module name: EMSMDB32.DLL, version: 12.0.6539.5000, time stamp: 0x4c1246f8 Exception code: 0xc0000005 Fault offset: 0x0005d8e2 Faulting process id: 0xf6c Faulting application start time: 0x01cb6633f33384f3 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\OUTLOOK.EXE Faulting module path: c:\progra~2\micros~1\office12\EMSMDB32.DLL Report Id: 0d4a2eab-d231-11df-80a0-4061868f5d10 I also get this: Faulting application name: OUTLOOK.EXE, version: 12.0.6539.5000, time stamp: 0x4c12486d Faulting module name: olmapi32.dll, version: 12.0.6538.5000, time stamp: 0x4bfc6ad9 Exception code: 0xc0000005 Fault offset: 0x002357a9 Faulting process id: 0x5e4 Faulting application start time: 0x01cb661f4546aa77 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\OUTLOOK.EXE Faulting module path: c:\progra~2\micros~1\office12\olmapi32.dll Report Id: a4a90658-d224-11df-80a0-4061868f5d10 The Excel error is this: Faulting application name: EXCEL.EXE, version: 12.0.6535.5002, time stamp: 0x4bd2a7f1 Faulting module name: KERNELBASE.dll, version: 6.1.7600.16385, time stamp: 0x4a5bdbdf Exception code: 0xe06d7363 Fault offset: 0x0000b727 Faulting process id: 0x14a8 Faulting application start time: 0x01cb61ab7bc0abab Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\EXCEL.EXE Faulting module path: C:\Windows\syswow64\KERNELBASE.dll Report Id: ba0c454b-cd9e-11df-80a0-4061868f5d10 Also have gotten this for PowerPoint: Faulting application name: POWERPNT.EXE, version: 12.0.6500.5000, time stamp: 0x49a68f9d Faulting module name: COMShim.dll, version: 2010.3.325.110, time stamp: 0x4c51e0b1 Exception code: 0x40000015 Fault offset: 0x0001e388 Faulting process id: 0x1480 Faulting application start time: 0x01cb5fe9a0660e81 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\POWERPNT.EXE Faulting module path: C:\Program Files (x86)\FactSet\COMShim.dll Report Id: e03d2a21-cbdc-11df-9bc8-4061868f5d10 (Some of the above lines edited to keep you from scroll horizontally.) Lastly, I get this error several times a day, I don't think it is related but maybe it is: Failed extract of third-party root list from auto update cab at: http://www.download.windowsupdate.com/msdownload/update/v3/static/trustedr/en/authrootstl.cab with error: A required certificate is not within its validity period when verifying against the current system clock or the timestamp in the signed file. Any ideas? This is driving me nuts.

  Read the article

• Apache fails to start after WHM easyapache update

  - by Vigrond

  Tryin to get some light shed on this issue Running CentOS I upgraded Apache using easyapache to 2.2 All was well I then used WHM to update Mysql to 5.5 This succeeded but now Apache will not start. The error log was reporting things like [Sun Apr 15 00:44:57 2012] [alert] getpwuid: couldn't determine user name from uid 4294967295, you probably need to modify the User directive [Sun Apr 15 02:27:30 2012] [notice] suEXEC mechanism enabled (wrapper: /usr/local/apache/bin/suexec) [Sun Apr 15 02:27:30 2012] [warn] pid file /usr/local/apache/logs/httpd.pid overwritten -- Unclean shutdown of previous Apache run? [Sun Apr 15 02:27:30 2012] [alert] getpwuid: couldn't determine user name from uid 4294967295, you probably need to modify the User directive [Sun Apr 15 02:27:30 2012] [alert] getpwuid: couldn't determine user name from uid 4294967295, you probably need to modify the User directive [Sun Apr 15 02:27:30 2012] [alert] getpwuid: couldn't determine user name from uid 4294967295, you probably need to modify the User directive [Sun Apr 15 02:27:30 2012] [alert] getpwuid: couldn't determine user name from uid 4294967295, you probably need to modify the User directive [Sun Apr 15 02:27:30 2012] [alert] getpwuid: couldn't determine user name from uid 4294967295, you probably need to modify the User directive [Sun Apr 15 02:27:30 2012] [notice] Apache/2.2.22 (Unix) mod_ssl/2.2.22 OpenSSL/0.9.8e-fips-rhel5 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 configured -- resuming normal operations [Sun Apr 15 02:27:30 2012] [alert] Child 4063 returned a Fatal error... Apache is exiting! So I tried to recompile using easyapache again, but easyapache just hangs I tried with base php settings - and it always gets stuck on "bf804000-bf819000 rw-p 7ffffffe9000 00:00 0 [stack]" At this point in cpanel the status says "create srm.conf and access.conf for mod_frontpage" I have tried things like rpm --rebuilddb yum clean all yum update with no luck. I'm kind of running out of ideas, and wondering if anyone could point me to the right direction.

  Read the article

• SQL Server 2008 Cluster Installation - First network name always fails

  - by boflynn

  I'm testing failover clustering in Windows Server 2008 to host a SQL Server 2008 installation using this installation guide. My base cluster is installed and working properly, as well as clustering the DTC service. However, when it comes time to install SQL Server, my first attempt at installation always fails with the same message and seems to "taint" the network name. For example, with my previous cluster attempt, I was installing SQL Server as VSQL. After approximately 15 attempts of installation and trying to resolve the errors, e.g. changing domain accounts for SQL, setting SPNs, etc., I typoed the network name as VQSL and the installation worked. Similarly on my current cluster, I tried installing with the SQL service named PROD-C1-DB and got the same errors as last time until I tried changing the name to anything else, e.g. PROD-C1-DB1, SQL, TEST, etc., at which point the install works. It will even install to VSQL now. While testing, my install routine was: Run setup.exe from patched media, selecting appropriate options After the install fails, I'd chose "Remove node from a SQL Server failover cluster" and remove the single, failed, node Attempt to diagnose problem, inspect event logs, etc. Delete the computer account that was created for the SQL Service from Active Directory Delete the MSSQL10.MSSQLSERVER folder from the shared data drive The error message I receive from the SQL Server installer is: The following error has occurred: The cluster resource 'SQL Server' could not be brought online. Error: The group or resource is not in the correct state to perform the requested operation. (Exception from HRESULT: 0x8007139F) Along with hundreds of the following errors in the Application event log: [sqsrvres] checkODBCConnectError: sqlstate = 28000; native error = 4818; message = [Microsoft][SQL Server Native Client 10.0][SQL Server]Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. System configuration notes: Windows Server 2008 Enterprise Edition x64 SQL Server 2008 Enterprise Edition x64 using slipstreamed SP1+CU1 media Dell PowerEdge servers Fibre attached storage

  Read the article

• Destroyed user account on OS X with dscl; how to restore? [migrated]

  - by Sam Ritchie

  I was trying to create a new user on my OS X Lion machine, and somehow managed to destroy my own user's account. Here are the steps I took; hopefully someone here can recognize what I did, and maybe identify some way around this. First, I ran these commands: sudo dscl localhost -create /Local/Default/Users/elasticsearch sudo dscl localhost -create /Local/Default/Users/elasticsearch /bin/bash # mistake! sudo dscl localhost -create /Local/Default/Users/elasticsearch UserShell /bin/bash sudo dscl localhost -create /Local/Default/Users/elasticsearch RealName "Elastic Search" sudo dscl localhost -create /Local/Default/Users/elasticsearch UniqueID 503 # MY uniqueID sudo dscl localhost -create /Local/Default/Users/elasticsearch PrimaryGroupID 1000 sudo dscl localhost -create /Local/Default/Users/elasticsearch NFSHomeDirectory /Local/Users/elasticsearch The big mistake I made here was using "503", which was my user's UniqueID. Immediately my shell username changed to "elasticsearch". I fiddled around, tried to change the current user with sudo su -u sritchie, but this didn't work. On restart, only the "Elastic Search" user was available. I logged into the Lion Recovery partition and reset the root password. After logging in as root and checking on the terminal, I made the remarkable discovery that my home folder was totally empty. I deleted the elasticsearch user, but it made no difference. I don't see anything in Deleted Users either. The odd thing is that when I log in now as myself (sritchie) I can see desktop icons with previews. I can even open a few text files from the Downloads folder if I use the dock alias to Downloads. Could this data be hiding somewhere? Any help would be REALLY appreciated! Thanks, Sam

  Read the article

• Domino nchronos.exe multiple instances causing server to die, and Sametime problems

  - by Kevin

  I've had this problem for a few months now. I thought it started when I installed the Traveller software on the server to add ActiveSync support, but I removed that and the problem still persists. Basically new instances of "nchronos.exe" keeps spawning (and not ending), so over a period of a few days the server eventually gets drowned in nchronos.exe processes, stops responding and I need to kill Domino. My process count the last time was up at about 330, and when I killed it and restarted the Domino my process count went to 160. I'm running Domino 8.5.1 with Fix Pack 2. I don't know if it's relevant, but my Domino server was also acting as a Sametime server. At around the same time that nchronos started playing up sametime also stopped working. None of my users can connect to sametime and in the domino log it keeps telling me "stpolicy.exe" has terminated. I've googled for that and tried a few things, but nothing seems to make sametime work again. Any thoughts?? Cheers, Kevin

  Read the article

• PHPMyAdmin: "General relation features: Disabled"

  - by Simón

  I've been looking around for something like this for a while, and I've found some tips on similar issues, but not exactly the same. I really don't know what to do. I downloaded and installed WAMP, and I have a MySQL and PHPMyAdmin setup according to common indications that can be found everywhere (securing MySQL root account, etc.). When I log into PHPMyAdmin (either as root or as pma), I see the following message at the bottom of the page: The additional features for working with linked tables have been deactivated. To find out why click here. And when following the link, got a page with the following: Server: localhost $cfg['Servers'][$i]['pmadb'] ... OK $cfg['Servers'][$i]['relation'] ... OK General relation features: Disabled $cfg['Servers'][$i]['table_info'] ... OK Display Features: Disabled $cfg['Servers'][$i]['table_coords'] ... OK $cfg['Servers'][$i]['pdf_pages'] ... OK Creation of PDFs: Disabled $cfg['Servers'][$i]['column_info'] ... OK Displaying Column Comments: Disabled Bookmarked SQL query: Disabled Browser transformation: Disabled $cfg['Servers'][$i]['history'] ... OK SQL history: Disabled $cfg['Servers'][$i]['designer_coords'] ... OK Designer: Disabled Somebody please explain to me, why the heck if all settings are "OK" the features remain "Disabled"? Note: at first all the settings were "not OK" and I managed to add the settings to config.inc.php, and then created the tables using scripts/create_tables.php. Of course I have already tried restarting the server or clearing the browser cache (several times, so I am sure the problem comes elsewhere).

  Read the article

• Enabling CURL on Ubuntu 11.10

  - by Afsheen Khosravian

  I have installed curl: sudo apt-get install curl libcurl3 libcurl3-dev php5-curl and I have updated my php.ini file to include(I also tried .so): extension=php_curl.dll To test if curl is working I created a file called testCurl.php which contains the following: <?php echo ‘<pre>’; var_dump(curl_version()); echo ‘</pre>’; ?> When I navigate to localhost/testCurl.php I get an error: HTTP Error 500 Heres a snippet from the error log: PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20090626+lfs/php_curl.dll' - /usr/lib/php5/20090626+lfs/php_curl.dll: cannot op$ PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20090626+lfs/sqlite.so' - /usr/lib/php5/20090626+lfs/sqlite.so: cannot open sha$ [Sun Dec 25 12:10:17 2011] [notice] Apache/2.2.20 (Ubuntu) PHP/5.3.6-13ubuntu3.3 with Suhosin-Patch configured -- resuming normal operations [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/ [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/ [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/ [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/` Can anyone help me to get curl working? The problem was with the original test code. I used a new test file containing this and curl is now working: <?php ## Test if cURL is working ## ## SCRIPT BY WWW.WEBUNE.COM (please do not remove)## echo '<pre>'; var_dump(curl_version()); echo '</pre>'; ?>

  Read the article

• Server nearly unusable when doing disk writes

  - by Wikser

  My question closely relates to my last question here on serverfault. I was copying about 5GB from a 10 year old desktop computer to the server. The copy was done in Windows Explorer. In this situation I would assume the server to be bored by the dataflow. But as usual with this server, it really slowed down. At least I could work with the remote session, even there was some serious latency. The copy took its time (20min?). In this time I went to a colleague and he tried to log in in the same server via remote desktop (for some other reason). It took about a minute to get to the login screen, a minute to open the control panel, a minute to open the performance monitor, ... Icons were loading maybe one per second. We saw the following (from memory): CPU: 2% Avg. Queue Length: 50 Pages/sec: 115 (?) There was no other considerable activity on the server. The server seldom serves some ASP.NET pages, which became also very slow in this time. The relevant configuration is as follows: Windows 2003 SEAGATE ST3500631NS (7200 rpm, 500 GB) LSI MegaRAID based RAID 5 4 disks, 1 hot spare Write Through No read-ahead Direct Cache Mode Harddisk-Cache-Mode: off Is this normal behaviour for such a configuration? What measurements could give further clues? Is it reasonable to reduce the priority of such copy I/O and favour other processes like the remote desktop? How would you do that? Many thanks!

  Read the article

• hosts.deny not blocking ip addresses

  - by Jamie

  I have the following in my /etc/hosts.deny file # # hosts.deny This file describes the names of the hosts which are # *not* allowed to use the local INET services, as decided # by the '/usr/sbin/tcpd' server. # # The portmap line is redundant, but it is left to remind you that # the new secure portmap uses hosts.deny and hosts.allow. In particular # you should know that NFS uses portmap! ALL:ALL and this in /etc/hosts.allow # # hosts.allow This file describes the names of the hosts which are # allowed to use the local INET services, as decided # by the '/usr/sbin/tcpd' server. # ALL:xx.xx.xx.xx , xx.xx.xxx.xx , xx.xx.xxx.xxx , xx.x.xxx.xxx , xx.xxx.xxx.xxx but i am still getting lots of these emails: Time: Thu Feb 10 13:39:55 2011 +0000 IP: 202.119.208.220 (CN/China/-) Failures: 5 (sshd) Interval: 300 seconds Blocked: Permanent Block Log entries: Feb 10 13:39:52 ds-103 sshd[12566]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12567]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12568]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12571]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:53 ds-103 sshd[12575]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root whats worse is csf is trying to auto block these ip's when the attempt to get in but although it does put ip's in the csf.deny file they do not get blocked either So i am trying to block all ip's with /etc/hosts.deny and allow only the ip's i use with /etc/hosts.allow but so far it doesn't seem to work. right now i'm having to manually block each one with iptables, I would rather it automatically block the hackers in case I was away from a pc or asleep

  Read the article

• 403 Forbidden error on Mac OSX - Apache and nginx

  - by tlianza

  Hi All, There are a million questions like this on Google, but I haven't found a solution to my problem. The default Apache install on my Mac is giving 403 Forbidden errors for everything (default directory, user home directory, virtual server, etc). After sifting through the config files, I figured I'd give nginx a try. Nginx serves files fine from it's home directory, but it won't serve files from a subfolder of my user directory. I've configured a simple virtual host, and requesting index.html returns a 403-forbidden. The error message in nginx's log file is pretty clear - it can't read the file: 2011/01/04 16:13:54 [error] 96440#0: *11 open() "/Users/me/Documents/workspace/mobile/index.html" failed (13: Permission denied), client: 127.0.0.1, server: local.test.com, request: "GET /index.html HTTP/1.1", host: "local.test.com" I've opened up this directory to everyone: drwxrwxrwx 6 me admin 204B Dec 31 20:49 mobile And all the files in it: $ ls -lah mobile/ total 24 drwxrwxrwx 6 me admin 204B Dec 31 20:49 . drwxr-xr-x 71 me me 2.4K Dec 31 20:41 .. -rw-r--r--@ 1 me me 6.0K Jan 2 18:58 .DS_Store -rwxrwxrwx 1 me admin 2.1K Jan 4 14:22 index.html drwxrwxrwx 5 me admin 170B Dec 31 20:45 nbproject drwxrwxrwx 5 me admin 170B Jan 2 18:58 script And yet, I cannot figure out why the nginx process cannot read index.html. It's running as the "nobody" user, but the permissions are set such that anyone can read them.

  Read the article

• Rewriting html links with modproxyperlhtml

  - by Juancho

  I'm trying to setup an Apache reverse proxy using mod_proxy and modproxyperlhtml. This is my scenario: Domain for the proxy: http : // www.myserver.com/ Destination server (the one behind the proxy): http : // myserver.foo.com/myapp/ I'm sorry that I have to space the URL but serverfault doesn't allow me to post more than two links as "spam protection mechanism" (ridiculous on a site where you ask questions about servers and it's really probable to post more than two times the same URL's to explain your question). The idea is to map http : // www.myserver.com/ to http : // myserver.foo.com/myapp/ . Note that the path on the proxy is / and on the destination server is /myapp/. All of the examples I can find on the net (like the one on the official documentation of modproxyperlhtml) are the other way around, ie. path on the proxy /myapp/ and path on the destination server /. This is my current config that doesn't work: ProxyPass / http : // myserver.foo.com/myapp/ ProxyPassReverse / http : // myserver.foo.com/myapp/ PerlInputFilterHandler Apache2::ModProxyPerlHtml PerlOutputFilterHandler Apache2::ModProxyPerlHtml SetHandler perl-script PerlSetVar ProxyHTMLVerbose "On" LogLevel Info <Location / > # ProxyPassReverse /myapp/ PerlAddVar ProxyHTMLURLMap "/myapp/ /" PerlAddVar ProxyHTMLURLMap "http : // myserver.foo.com /" </Location> The examples use the ProxyPassReverse inside the Location directive, but on my case doesn't work, only when outside. With this configuration the links aren't being replaced as they should be, my guess is that the location isn't being found, thus the rewrite rules aren't being applied. The error log only shows that it uncompresses the content, searches it but doesn't find anything: [Tue Nov 13 0842:05 2012] [warn] [ModProxyPerlHtml] Uncompressing text/html; charset=UTF-8, Content-Encoding: gzip\n [Tue Nov 13 08:42:05 2012] [warn] [ModProxyPerlHtml] Content-type 'text/html; charset=UTF-8' match: /(text\\/javascript|text\\/html|text\\/css|text\\/xml|application\\/.*javascript|application\\/.*xml)/is\n [Tue Nov 13 08:42:05 2012] [warn] [ModProxyPerlHtml] Compressing output as Content-Encoding: gzip\n [Tue Nov 13 08:42:06 2012] [warn] [ModProxyPerlHtml] Content-type 'text/html; charset=UTF-8' match: /(text\\/javascript|text\\/html|text\\/css|text\\/xml|application\\/.*javascript|application\\/.*xml)/is\n What could be wrong ?

  Read the article

• 1and1 ssh - connection refused

  - by kitensei

  I'm having troubles connecting through SSH to my 1&1 account. When I try to connect with command userXXX@host -p22 -vv I have the following output: OpenSSH_5.8p1 Debian-7ubuntu1, OpenSSL 1.0.0e 6 Sep 2011 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to mySite.com [ip_here] port 22. debug1: connect to address ip_here port 22: Connection refused Moreover, once I try to connect through SSH and it fails, even the HTTP access is dead, I cannot access the website through explorer anymore :/ please help < I'm running ubuntu 11.10 EDIT: don't know if it can help, here's the .htaccess of the 1and1 server Options +Indexes Satisfy any Order Deny,Allow Allow from 212.227.X.X Deny from all RemoveType .html .gif AuthType Basic AuthName "Access to /logs" AuthUserFile /kunden/homepages/43/d376072470/htpasswd Require user "user_here" and sftp.log: Mar 26 09:21:24 193.251.X USER_HERE Connection from 193.251.X port 51809 Mar 26 09:21:30 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:39 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:41 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:45 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:57 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 10:53:36 212.227.X tmp64459736-3228 Connection from 212.227.X port 23275 Mar 26 10:53:36 212.227.X tmp64459736-3228 Accepted password for tmp64459736-3228 from 212.227.X port 23275 ssh2 Mar 26 11:53:37 212.227.X tmp64459736-3228 Connection closed by 212.227.X Mar 26 18:58:17 212.227.X tmp64459736-5363 Connection from 212.227.X port 23353 Mar 26 18:58:17 212.227.X tmp64459736-5363 Accepted password for tmp64459736-5363 from 212.227.X port 23353 ssh2 Mar 26 19:53:36 212.227.X tmp64459736-8525 Connection from 212.227.X port 5166 Mar 26 19:53:36 212.227.X tmp64459736-8525 Accepted password for tmp64459736-8525 from 212.227.X port 5166 ssh2 Mar 26 19:58:17 212.227.X tmp64459736-5363 Connection closed by 212.227.X

  Read the article

• Using NX with no PasswordAuthentication SSH setup

  - by benmccann

  I'm trying to setup passwordless SSH access. My username is bmccann, so in /etc/ssh/sshd_config I added: PermitRootLogin no PasswordAuthentication no AllowUsers bmccann nx I ran ssh-keygen on the client and put ~/.ssh/id_rsa.pub from the client into ~/.ssh/authorized_keys on the server. I can now login with no password using the ssh command. However, I can no longer access the machine via NX as long as /etc/ssh/sshd_config has "PasswordAuthentication no". Server error logs: $ grep NX /var/log/messages Feb 11 01:25:51 bmccann-htpc NXSERVER-3.4.0-12[23552]: ERROR: Failed authentication. NXSsh exit status is:255 'NXNssUserManager::auth' Feb 11 01:25:51 bmccann-htpc NXSERVER-3.4.0-12[23552]: Failed SSHd authentication for user 'bmccann', to '127.0.0.1', port '22': 'NX> 204 Authentication failed.\n ' 'NXNssUserManager::auth' Feb 11 01:25:51 bmccann-htpc NXSERVER-3.4.0-12[23552]: ERROR: Error while trying to authenticate user:bmccann. NXNssUserManager::auth returned 255 'NXShell::handler_login' Feb 11 01:25:51 bmccann-htpc NXSERVER-3.4.0-12[23552]: ERROR: failed 'sshd authentication' for user 'bmccann' from '108.29.137.64'. NXShell::handler_login NXShell 373 What do I need to do to restore my NX access? Is there something I need to setup in the NX client so that it no longer asks me for a password?

  Read the article

• IIS 6 302, 401 Error

  - by lvandiest

  I'm having some problems accessing an ASP.NET website hosted on an internal iis 6 server that I am maintaining. Some users can get to the site, others (including myself can't). The app has Windows Authentication mode set in the web.config file, and Integrated Windows Authentication checked in the Website properties. Anonymous access is not checked. In the IIS logs, I see 2 lines when I make a request for the site's default page (Default.aspx). The first is a 401.2 error, and the 2nd is a 302.0 error. I've tried switching around as many security settings as I can think of, but had no luck yet. Can someone please help? I'm mainly a programmer, but have done a little IIS administration, so it is probably something quite simple I am missing. -- here are the log entries for my request to Default.aspx 2011-01-11 21:17:35 10.100.1.6 GET /MonthEndInventory/Default.aspx - 80 - 10.100.1.111 Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+6.1;+Trident/4.0;+SLCC2;+.NET+CLR+2.0.50727;+.NET+CLR+3.5.30729;+.NET+CLR+3.0.30729;+Media+Center+PC+6.0;+OfficeLiveConnector.1.4;+OfficeLivePatch.1.3;+.NET+CLR+1.1.4322;+Tablet+PC+2.0;+.NET4.0C;+.NET4.0E;+InfoPath.3;+MS-RTC+LM+8) 401 2 2148074254 2011-01-11 21:17:35 10.100.1.6 GET /MonthEndInventory/Default.aspx - 80 DOMAIN\myuserid 10.100.1.111 Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+6.1;+Trident/4.0;+SLCC2;+.NET+CLR+2.0.50727;+.NET+CLR+3.5.30729;+.NET+CLR+3.0.30729;+Media+Center+PC+6.0;+OfficeLiveConnector.1.4;+OfficeLivePatch.1.3;+.NET+CLR+1.1.4322;+Tablet+PC+2.0;+.NET4.0C;+.NET4.0E;+InfoPath.3;+MS-RTC+LM+8) 302 0 0

  Read the article

• Windows Remote Desktop: "configuring remote session" closes without error

  - by icelava

  I have a desktop/laptop pair at home operating x64 Windows 7 (the desktop was upgraded from Windows Vista, works just fine). I remote desktop to them on a daily basis when outside. In recent weeks, I would occasionally fail to connect to my desktop. It can connect and authenticate fine, but the "configuring remote session" dialog would simply close and not show me the desktop window or any error message. There is no error event log relating to this on the desktop computer. Some suggestions call for disabling remote audio, which mine already is, but trying different audio modes did not yield any different result. I am not too sure if this is related to video card drivers (they do get auto-updated), since remote desktop video is supposed to steer via a virtual device driver? Nonetheless the desktop operates three monitors via an ATI Radeon HD5770 (1 Displayport, 2 DVI). I do not see a real problem with that since I can mostly connect and operate it remotely. I try to "remote tunnel" via my home laptop but obviously won't work either as the problem lies in the desktop. What other conditions can cause remote desktop to break without error? UPDATE I came home and still couldn't connect to the desktop until I restarted the entire system.

  Read the article

• Migrating to CF9: trouble getting JRun working with SSL

  - by DaveBurns

  I have a client on MX7 who wants to migrate to CF9. I have a dev environment for them on my WinXP machine where I've configured MX7 to run with JRun's built-in web server. I've had that working for a long time with both regular and SSL connections. I installed CF9 yesterday side-by-side with the existing MX7 install to start testing. The install was smooth and detected MX7, adjusted CF9's port numbers for no conflict, etc. Testing started well: MX7 over regular and SSL still worked and CF9 worked over regular HTTP. But I can't get CF9 to work with SSL. I installed a new certificate with keytool, FireFox (v3.6) complained about it being unsigned, I added it to the exception list, and now I get this: Secure Connection Failed An error occurred during a connection to localhost:9101. Peer reports it experienced an internal error. (Error code: ssl_error_internal_error_alert) I've been Googling that in all variations but can't find much help to get past this. I don't see any info in any log files either. FWIW, here's my SSL config from SERVER-INF/jrun.xml: <service class="jrun.servlet.http.SSLService" name="SSLService"> <attribute name="enabled">true</attribute>` <attribute name="interface">*</attribute> <attribute name="port">9101</attribute> <attribute name="keyStore">{jrun.rootdir}/lib/mykey</attribute> <attribute name="keyStorePassword">*deleted*</attribute> <attribute name="trustStore">{jrun.rootdir}/lib/trustStore</attribute> <attribute name="socketFactoryName">jrun.servlet.http.JRunSSLServerSocketFactory</attribute> <attribute name="deactivated">false</attribute> <attribute name="bindAddress">*</attribute> <attribute name="clientAuth">false</attribute> </service> Anyone here know of any issues re setting up SSL and CF9? Anyone had success with it? Dave

  Read the article

• How to diagnose website performance/app pool recycling with Windows 2008/IIS7

  - by ilasno

  Ok, so there are various symptoms here (clients and and our own employees complaining of intermittent slowdowns, getting 'kicked out' to login page or just having a save request not properly save the submitted data). The environment: Windows Server 2008 (Datacenter), Service Pack 2, 64-bit, 2x2.8 GHz processors, 7.5 GB RAM MS SQL Server 2008 (running on the same machine) IIS 7 There are ~10 websites running on the server, each in their own application pool - most of these pools are running in Integrated mode, 2 are in Classic, all are on .NET 2.0 and all run as ApplicationPoolIdentity. I'm trying to analyze, diagnose, and troubleshoot and am struggling with where to get more info about what could be happening. Here are some steps i have already taken: Set each application pool to recycle once per day, and removed any other automatic recycling Set a Virtual Memory Limit for each to 1024000KB (1GB) Enabled ALL 'Generate Recycle Event Log Entry' entries (Config Changes, Isapi Reported Unhealthy, Manual Recycle, Private Memory Limit Exceeded, Regular Time Interval, Request Limit Exceeded, Specific Time, Virtual Memory Limit Exceeded) I have seen the app pool processes recycle (in Task Manager) - a new one will start up, and then the first one dies off - and this has happened without the memory or time going over the settings. This is a fairly new server, and most of these came from Windows Server 2003/IIS6. Any 'next steps' for setting up information gathering, logging, diagnosing, etc. would be much appreciated! j

  Read the article

• ProFTPD / PAM issues with new centos/virtualmin install

  - by iamthewit

  Hi All, I just installed CentOS 5.4 on a rackspace cloud server and installed virtualmin which all seemed to go fine. The only problem I have is that I can not access the virtual servers directories via FTP. I get the following from filezilla: Status: Connecting to 1.1.1.1:21... Status: Connection established, waiting for welcome message... Response: 220 FTP Server ready. Command: USER username Response: 331 Password required for username. Command: PASS ******* Response: 230 User username logged in. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is current directory. Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (1,1,1,1,216,214) Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing and I get this from my /var/secure/log file Sep 22 19:40:42 stickeeserver proftpd: pam_unix(proftpd:session): session opened for user username by (uid=0) Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - USER nastypasty: Login successful. Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - Preparing to chroot to directory '/home/username' Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - mod_delay/0.5: delaying for 728 usecs Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - error setting IPV6_V6ONLY: Protocol not available Any help would be greatly appreciated, I'm not totally new to Linux but it's not my strongest subject. I do like to know exactly why problems occur though and how exactly to fix them so the more detail the better! cheers

  Read the article

• Inconsistent DHCP replies with Windows 2008R2 DHCP server

  - by verbalicious

  I've got a Windows 2008R2 standard server running DHCP services. We've noticed that certain clients are receiving inconsistent DHCP replies. We have over 175 Windows workstations in this VLAN that don't seem to have trouble getting DHCP leases. However, PXE-booting clients trying to reach our DHCP server are able to get a lease inconsistently. Additionally, we tried using the "dhcping" tool against our DHCP server and found that roughly two of every three requests time out with "no answer" -- and this holds true when we set the timeout value on dhcping to 20seconds. After a failed attempt, however, we may get a dhcp lease reply immediately with dhcping. This leads me to believe that this issue isn't confined to PXE booting clients, but something more systemic with my LAN layer2 or DHCP. And that possibly my 175 windows clients are experiencing this in some form without my knowledge. We have over 30% of our scope available so the addresses are there. I was unable to find anything in the Windows server "DHCP-Server" log. Of course, my goal is to have my DHCP server reply to every request that it receives on the LAN!

  Read the article

• Windows 7 x64 RTM USB Port Has Power But Won't Recognize Mouse/Keyboard/Anything

  - by ben

  I have an odd error that doesn't seem to fit in with any of the other odd Windows 7 x64 USB errors that have been kicked up on Google. Here we go: Uninstalled Tortoise SVN and clicked restart computer. My machine had been up for around 28 days On reboot my mouse and keyboard failed to work anymore, couldn't log in. Tried every USB port I have on my Dell 390 and the ports on my Dell 19's, nothing worked. They had power but Windows would not respond when I manipulated the keyboard/mouse. Rebooted my computer and pressed F2 to get into bios, my keyboard is working fine in bios. Keyboard and mouse work fine on other computers when using USB. Found adapters for keyboard and mouse to convert from USB to PS/2 ports, works fine. I'm actually typing this question on the same keyboard, same computer, just using PS/2 ports for my mouse and keyboard. It appears to be a Windows 7 x64 issue. Other things I have tried: Multiple other mice and keyboards, iphone, all with no luck. Each one gets power, but Windows never tries to install drivers or sees that they are connected. Uninstall and reinstall all USB drivers. Drives uninstall and reinstall fine and report no errors in Control Panel. In Power Management I disallow Windows from turning off USB ports to save power Installed the latest nVidia drivers for my graphics card, no change. Anyplace else I can look/try? Thanks!

  Read the article

< Previous Page | 570 571 572 573 574 575 576 577 578 579 580 581  | Next Page >