Search Results

Search found 7455 results on 299 pages for 'power cable'.

Page 58/299 | < Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >

  • Getting WLAN on my Laptop to work (Medion MD98300)

    - by Anand Böhmer
    Dear Ubuntu Community, I am having difficulties to get the WLAN Adapter on my Medion 98300 Laptop to work. The WLAN Card seems to be connected through an internal USB Interface and the Card itself had shown up as a wirelles Network while installing Ubuntu. I have tried a few things earlier, but none of my google reasearches have brought me to a working solution... I am quite new to the Linux System and only knoew a couple of terminal commands so far, so I probably have missed out on a few possible solutions. Maybe you can help me? Thank you very much in advance! A fre minimal technical Details: AMD Turion 64 X2 Dual-Core Mobile Technolgie TL-50 NVIDIA GeForce Go 6150 SanDisk 64GB SSD 2GB RAM DDR2 667 nForce Chipset (I forgt the Version, but deductable from the GPU I guess) WiFi: ZyDAS ZD1211B 802.11g Thank's a lot again! :) UPDATE: I tried around myself a little and found a guide on the Linux Mint forums that helped! I already had tried to install the linux backport modules etc. What I finally did was update the linux firmware and run the following command: echo "options acer_wmi wirelles=1" sudo tee /etc/modprobe.d/acer_wmi.conf and rebooted now I found and could connect to networks, but unfortunately I found, that the link quality was very bad, around 40 to 50. Eventhough my Router is running at high power and is only 6 Meters away! I then switched a few channels, but that did not improve much. Before, under Windows, I had a very good link quality and had the entire 16mbit/s internet connection at disposal, now I can only get about 3-5Mbit/s. better then nothing, but still pretty bad! The "TX power" is fixed on 20dBm and iwconfig says, that the "Power Management" is off... Maybe the power of the module is set too low?... UPDATE2: I figured that 20dBm is a normal power output. I even tried to change the power using iwconfig wlan0 txpower INTEGERHERE but, obviously my "Card" does not support more then 20. More would probably be illegal as well, so I won't even use more then 20. I guess that I will have to figure out a way, or maybe just switch cards. Are the Mailboard-USB-Connectors on a laptop of the same property as the standard external ones? If so, I could simply solder a micro Wirelless N Adapter onto the board :)

    Read the article

  • Plugged in Not Charging.

    - by Eric Johnson
    Suggested steps to fix the nasty Windows power management issue of plugged in not charging. Option 1: Disconnect AC Shutdown Remove battery Connect AC Startup Under the Batteries category, right-click all of the Microsoft ACPI Compliant Control Method Battery listings, and select Uninstall (it’s ok if you only have 1). Shutdown Disconnect AC Insert battery Connect AC Startup Option 2: Turn off laptop. Unplug AC power. Remove battery. Replace AC power. Turn on laptop, allow OS to boot. Once logged in to the machine, perform a normal shut down. Unplug AC power. Replace battery. Replace AC power. Turn on laptop, allow OS to boot. The battery should once again be charging as normal Additional troubleshooting techniques: Check battery charging status in the BIOS Update BIOS Replace Battery (I did this and the new battery is not charging) See if the battery charging light works when the laptop is powered down. Supporting Links: http://jeffreypalermo.com/blog/plugged-in-not-charging-windows-7-solution/ http://social.technet.microsoft.com/Forums/en/itprovistahardware/thread/741398c6-a733-482c-a33c-2b61d9bc2984 http://www.youtube.com/watch?v=6Xf-ipP0wSY&feature=fvw

    Read the article

  • How I Work: Staying Productive Whilst Traveling

    - by BuckWoody
    I travel a lot. Not like some folks that are gone every week, mind you, although in the last month I’ve been to: Cambridge, UK; Anchorage, AK; San Jose, CA; Copenhagen, DK, Boston, MA; and I’m currently en-route to Anaheim, CA.  While this many places in a month is a bit unusual for me, I would say I travel frequently. I’ve travelled most of my 28+ years in IT, and at one time was a consultant traveling weekly.   With that much time away from my primary work location, I have to find ways to stay productive. Some might say “just rest – take a nap!” – but I’m not able to do that. For one thing, I’m a very light sleeper and I’ve never slept on a plane - even a 30+ hour trip to New Zealand in Business Class - so that just isn’t option. I also am not always in the plane, of course. There’s the hotel, the taxi/bus/train, the airport and then all that over again when I arrive. Since my regular jobs have many demands, I have to get work done.   Note: No, I’m not always focused on work. I need downtime just like everyone else. Sometimes I just think, watch a movie or listen to tunes – and I give myself permission to do that anytime – sometimes the whole trip. I have too fewheartbeats left in life to only focus on work – it’s just not that important, and neither am I. Some of these tasks are letters to friends and family, or other personal things. What I’m talking about here is a plan, not some task list I have to follow. When I get to the location I’m traveling to, I always build in as much time as I can to ensure I enjoy those sights and the people I’m with. I would find traveling to be a waste if not for that.   The Unrealistic Expectation As I would evaluate the trip I was taking – say a 6-8 hour flight – I would expect to get 10-12 hours of work done. After all, there’s the time at the airport, the taxi and so on, and then of course the time in the air with all of the room, power, internet and everything else I needed to get my work done. I would pile up tasks at home, pack my bags, and head happily to the magical land of the TSA.   Right. On return from the trip, I had accomplished little, had more e-mails and other work that had piled up, and I was tired, hungry, and unorganized. This had to change. So, I decided to do three things: Segment my work Set realistic expectations Plan accordingly  Segmenting By Available Resources The first task was to decide what kind of work I could do in each location – if any. I found that I was dependent on a few things to get work done, such as power, the Internet, and a place to sit down. Before I fly, I take some time at home to get all of the work I’d like to accomplish while away segmented into these areas, and print that out on paper, which goes in my suit-coat pocket along with a mechanical pencil. I print my tickets, and I’m all set for the adventure ahead. Then I simply do each kind of work whenever I’m in that situation. No power There are certain times when I don’t have power available. But not only that, I might not even be able to use most of my electronics. So I now schedule as many phone calls as I can for the taxi/bus/train ride and the airports as I can. I have a paper notebook (Moleskine, of course) and a pencil and I print out any notes or numbers I need prior to the trip. Once I’m airborne or at the airport, I work on my laptop. I check and respond to e-mails, create slides, write code, do architecture, whatever I can.  If I can’t use any electronics, or once the power runs out, I schedule time for reading. I can read at the airport or anywhere, actually, even in-flight or any other transport. I “read with a pencil”, meaning I take a lot of notes, which I liketo put in OneNote, but since in most cases I don’t have power, I use the Moleskine to do that. Speaking of which, sometimes as I’m thinking I come up with new topics, ideas, blog posts, or things to teach in my classes. Once again I take out the notebook and write it down. All of these notes get a check-mark when I get back to the office and transfer the writing to OneNote. I’ve tried those “smart pens” and so on to automate this, but it just never works out. Pencil and paper are just fine. As I mentioned, sometime I just need to think. I’ll do nothing, and let my mind wander, thinking of nothing in particular, or some math problem or science question I’m interested in. My only issue with this is that I communicate tothink, and I don’t want to drive people crazy by being that guy that won’t shut up, so I think in a different way. Power, but no Internet or Phone If I have power but no Internet or phone, I focus on the laptop and the tablet as before, and I also recharge my other gadgets. Power, Internet, Phone and a Place to Work At first I thought that when I arrived at the hotel or event I could get the same amount of work done that I do at the office. Not so. There’s simply too many distractions, things you need, or other issues that allow this. Of course, Ican work on any device, read, think, write or whatever, but I am simply not as productive as I am in my home office. So I plan for about 25-50% as much work getting done in this environment as I think I could really do. I’ve done some measurements, and this holds out to be true almost every time. The key is that I re-set my expectations (and my co-worker’s expectations as well) that this is the case. I use the Out-Of-Office notices to let people know that I’m just not going to be 100% at this time – it’s hard for everyone, but it’s more honest and realistic, and I’d rather they know that – and that I realize that – than to let them think I’m totally available. Because I’m not – I’m traveling. I don’t tend to put too much detail, because after all I don’t necessarily want to let people know when I’m not home :) but I do think it’s important to let people that depend on my know that I’ll get back with them later. I hope this helps you think through your own methodology of staying productive when you travel. Or perhaps you just go offline, and don’t worry about any of this – good for you! That’s completely valid as well.   (Oh, and yes, I wrote this at 35K feet, on Alaska Airlines on a trip. :)  Practice what you preach, Buck.)

    Read the article

  • A case for not installing your own software

    - by James Gentsch
    This week I watched some of the Oracle Open World presentations (from the comfort of my Oracle office) and happened on some of Larry Ellison’s comments about cloud computing and engineered systems.  Larry said he sees the move to these as analogous to the moves made by the original adopters of electricity.  The argument goes that the first consumers of electricity had to set up their own power plant.  Then, as the market and infrastructure for electricity matured, power consumers moved from using their own personal power plant to purchasing power from another entity that was focused on power production as their primary product. In the end this was a cheaper and more reliable solution. Now, there are lots of compelling reasons to be looking very seriously at cloud computing and engineered systems for enterprise application deployment.  However, speaking as a software developer of enterprise applications, the part of this that I really love (besides Larry’s early electricity adopter analogy) is that as a mode of application deployment it provides me and my customers a consistent environment in which the applications I am providing will be run.  This cuts way down on the environmental surprises that consistently lead to the hated “well, it works here” situation with the support desk. And just to be clear, I think I hate this situation more than my clients, who I think are happy that at least it is working somewhere.  I hate this because when a problem happens, and let’s face it customers are not wasting their time calling in easy problems, we are seriously disabled when we cannot reproduce the issue which is triggered by something unforeseen in the environment where the application is running.  This situation is incredibly frustrating and an all too often occurrence. I look selfishly forward to cloud computing and engineered systems dramatically reducing the occurrence of problems triggered by unforeseen environmental situations in the software I am responsible for.  I think this is an evolutionary game changer that will be a huge benefit to the reliability and consistent performance of the software for my customers, and may make “well, it works here” a well forgotten phase for future software developers. It may even impact the stress squeeze toy industry.  Well, maybe at least for my group.

    Read the article

  • What algorithm can calculate the power set of a given set?

    - by ross
    I would like to efficiently generate a unique list of combinations of numbers based on a starting list of numbers. example start list = [1,2,3,4,5] but the algorithm should work for [1,2,3...n] result = [1],[2],[3],[4],[5] [1,2],[1,3],[1,4],[1,5] [1,2,3],[1,2,4],[1,2,5] [1,3,4],[1,3,5],[1,4,5] [2,3],[2,4],[2,5] [2,3,4],[2,3,5] [3,4],[3,5] [3,4,5] [4,5] Note. I don't want duplicate combinations, although I could live with them, eg in the above example I don't really need the combination [1,3,2] because it already present as [1,2,3]

    Read the article

  • Why are textures always square powers of two? What if they aren't?

    - by Keavon
    Why are the resolution of textures in games always a power of two (128x128, 256x256, 512x512, 1024x1024, etc.)? Wouldn't it be smart to save on the game's file size and make the texture exactly fit the UV unwrapped model? What would happen if there was a texture that was not a power of two? Would it be incorrect to have a texture be something like 256x512, or 512x1024? Or would this cause the problems that non-power-of-two textures may cause?

    Read the article

  • nginx returning authentication in IE

    - by James MacLeod
    I am having a few issues with an nginx server. I have a site setup that keeps requesting authentication when accessed from IE but in firefox and safari the site is fine no request for authentication. Reading around the web I can see that it could be the gzip that may be causing errors, but the other sites are working without issue. Here is the config: user sysadmin sysadmin; worker_processes 8; error_log logs/error.log debug; events { worker_connections 1024; } http { passenger_root /usr/lib/ruby/gems/1.8/gems/passenger-2.2.9; passenger_ruby /usr/bin/ruby1.8; include mime.types; default_type application/octet-stream; client_header_timeout 3m; client_body_timeout 3m; client_max_body_size 5m; send_timeout 3m; client_header_buffer_size 1k; large_client_header_buffers 4 4k; gzip on; gzip_min_length 1100; gzip_buffers 4 8k; gzip_types text/plain; output_buffers 1 32k; postpone_output 1460; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 75 20; server { listen 80; server_name .reg-power.com .reg-power.co.uk .reg-power.eu .reg-power.eu.com .reg-power.net .reg-power.org .reg-power.org.uk .reg-power.uk.com .regegen.eu .regpower.co.uk .regpower.eu .regpower.eu.com .regpower.net .regpower.org .regpower.org.uk .regpower.uk.com .renegen.com .renegen.eu .renewableenergygeneration.co.uk .renewableenergygeneration.com reg.rails1.flowhost.co.uk; root /home/sysadmin/reg/current/public; passenger_enabled on; rails_env production; index index.html; } server { listen 80; server_name media.reg-power.com; root /home/sysadmin/admin/current/public; index index.html; } server { listen 80; server_name admin.reg-power.com admin.rails1.flowhost.co.uk; root /home/sysadmin/admin/current/public; passenger_enabled on; rails_env production; index index.html; } server { listen 80; server_name .livingfuels.co.uk livingfuels.rails1.flowhost.co.uk; root /home/sysadmin/livingfuels/current/public; passenger_enabled on; rails_env production; index index.html; } server { listen 80; server_name .regbiopower.com .regbiopower.co.uk regbiopower.rails1.flowhost.co.uk; root /home/sysadmin/regbiopower/current/public; passenger_enabled on; rails_env production; index index.html; } server { listen 80; server_name .clpwindprojects.co.uk clp.rails1.flowhost.co.uk; access_log /home/sysadmin/clp/logs/access.log; location / { root /home/sysadmin/clp; index index.php; if (-f $request_filename) { expires 30d; break; } if (!-e $request_filename) { rewrite ^(.+)$ /index.php?q=$1 last; } } location ~ .php$ { fastcgi_pass 127.0.0.1:49232; #this must point to the socket spawn_fcgi is running on. fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /home/sysadmin/clp$fastcgi_script_name; # same path as above fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT /home/sysadmin/clp; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; } } } As you can see there is no reference to a http authentication

    Read the article

  • Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

    - by jgottula
    I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

    Read the article

  • Creating basic ACPI event makes the system unusably slow

    - by skerit
    I want to change a few settings on my laptop when I switch to battery power. I created a new event in /etc/acpi/events/cust-battery and it looks like this: event=battery action=/home/skerit/power.sh I put a simple command in the power.sh file: echo This is a test >> /home/skerit/powertest Now, when I tail this file it shows "This is a test" 4-5 times upon switching to battery power. However, the system becomes totally unstable. It slows down significantly. I can't change anything in the terminal. The terminal and certain parts of the screen (like the gnome system monitor applet) go blank from time to time. What can be the cause of that? It's a simple echo that gets executed a few times!

    Read the article

  • Broadcom bcm4311 rev2 Full disabled on battery

    - by Antonio BG
    Ok this is my problem... My problem begins while ago when I installed ubuntu 10.10. (is the same with 11.04,11.10...) My wireless card is disabled if the power cord is unplugged, and the only way to fix this is rebooting my pc WITH the power cord plugged and if I use lspci command, it doesn't show me the wireless card. is like if I've removed the wireless board from my laptop port. I've searched a lot of solutions for bcmw4311 issues, but none of them fix my problem because when apply one of the fixes, if I unplug the cord, my wireless card it just gone away... I have dual boot on my pc(w7,ubuntu), I've tried with full installation just to see if this is the problem, but not, is the same. On windows all work correctly with and without power cord.. so this is not a hardware problem, is more like a kernel problem. anyway I can use wireless with power cord plugged, but c'mon this is a laptop not a desktop pc XD haha any help is welcome

    Read the article

  • Text-based one-on-one chat with Flash interface: what to power the backend?

    - by Zachary Burt
    Hey guys. I'm building a website where I hook people up so that they can anonymously vent to strangers. You either choose to be a listener, or a talker, and then you get catapulted into a one-on-one chat room. The reason for the app's construction is because you often can't vent to friends, because your deepest vulnerabilities can often be leveraged against you later on. (Like it or not, this is a part of human nature. Sad.) I'm looking for some insight into how I should architect everything. I found this neat tutorial, http://giantflyingsaucer.com/blog/?p=875, which suggests using python & stackless + flash. Someone else suggested I should try using p2p sockets, but I don't even know where to begin to look for info on that. Any other suggestions? I'd like to keep it simple. :^)

    Read the article

  • Uralelektrostroy Improves Turnaround Times for Engineering and Construction Projects by Approximately 50% with Better Project Data Management

    - by Melissa Centurio Lopes
    LLC Uralelektrostroy was established in 1998, to meet the growing demand for reliable energy supply, which included the deployment and operation of a modern power grid system for Russia’s booming economy and industrial sector. To rise to the challenge, the country required a company with a strong reputation and the ability to strategically operate energy production and distribution facilities. As a renowned energy expert, Uralelektrostroy successfully embarked on the mission—focusing on the design, construction, and operation of power grids, transmission lines, and generation facilities. Today, Uralelektrostroy leads the Russian utilities industry with operations across the country, particularly in the Ural, Western Siberia, and Moscow regions. Challenges: Track work progress through all engineering project development stages with ease—from planning and start-up operations, to onsite construction and quality assurance—to enhance visibility into complex projects, such as power grid and power-transmission-line construction Implement and execute engineering projects faster—for example, designing and building power generation and distribution facilities—by better monitoring numerous local subcontractors Improve alignment of project schedules with project owners’ requirements—awarding federal and regional authorities—to avoid incurring fines for missing deadlines Solutions: Used Oracle’s Primavera P6 Enterprise Project Portfolio Management 8.1 to streamline communication with customers and subcontractors through better data management and harmonized reporting, reducing construction project implementation and turnaround times by approximately 50%, on average Enabled fast generation of work-in-progress reports that track project schedules, budgets, materials, and staffing—from approval and material procurement, to construction and delivery Reduced the number of construction sites by nearly 30% (from 35 to 25) by identifying unprofitable sites—streamlining operations at the company’s construction site network and increasing profitability Improved project visibility by enabling managers to efficiently track project status, ensuring on-time reporting and punctual project deliveries to federal customers to reduce delay penalties to zero “Oracle’s Primavera P6 Enterprise Project Portfolio Management 8.1 drastically changed the way we run our business. We’ve reduced the number of redundant assets, streamlined project implementation and execution, and improved collaboration with our customers and contractors. Overall, the Oracle deployment helped to increase our profitability.” – Roman Aleksandrovich Naumenko, Head of Information Technology, LLC Uralelektrostroy Read the complete customer snapshot here.

    Read the article

  • Ranking players depending on decision making during a game

    - by tabchas
    How would I go about a ranking system for players that play a game? Basically, looking at video games, players throughout the game make critical decisions that ultimately impact the end game result. Is there a way or how would I go about a way to translate some of those factors (leveling up certain skills, purchasing certain items, etc.) into something like a curve that can be plotted on a graph? This game that I would like to implement this is League of Legends. Example: Player is Level 1 in the beginning. Gets a kill very early in the game (he gets gold because of the kill and it increases his "power curve"), and purchases attack damage (gives him more damage which also increases his "power curve". However, the player that he killed (Player 2), buys armor (counters attack damage). This slightly increases Player 2's own power curve, and reduces Player 1's power curve. There's many factors I would like to take into account. These relative factors (example: BECAUSE Player 2 built armor, and I am mainly attack damage, it lowers my OWN power curve) seem the hardest to implement. My question is this: Is there a certain way to approach this task? Are there similar theoretical concepts behind ranking systems that I should read up on? I've seen the ELO system, but it doesn't seem what I want since it simply takes into account wins and losses.

    Read the article

  • can not wakeup suspend com[puter

    - by user3528144
    I am unable to wake up my suspend Ubuntu 13.10. I click on suspend accidentally and HD led continues flash, but I tried to press any key keyboard, and CTL-ALT-PS R-E-I-S-U-B and power button, but can not wake up computer. I had to unplug power and put power back on to reboot computer. I would like to know are there any way to wake up suspend computer? Your help and information is great appreciated, regards, Iccsi,

    Read the article

  • How do I turn off PCI devices?

    - by ethana2
    With the purchase of an Intel SSD and 85WHr Li-ion battery and the linking of wifi and bluetooth to my laptop's wireless switch, extensive Intel PowerTop usage, switching from compiz to metacity, stopping of the desktop-couch daemon, removal of Ubuntu One and several other services from my startup, disabling of everything possible in my BIOS, and physical removal of my optical drive, I've gotten my battery life up fairly high, but I think there's still more to be done. Specifically, when I'm in class taking notes, I want to temporarily but completely power down: Ethernet Firewire USB ports SD card reader Optical drive Webcam Sound card PCMCIA slot ..without turning them off in my BIOS like they are now, if possible, because then I have to restart my computer to use any of them. As it stands, I still haven't managed to power down: Firewire USB connection to webcam sound card How do I tell Linux to disable and power down these devices? Is it true that any PCI slot can be physically powered down? My current idle power consumption is 7.9 watts plus the screen. (10.0W at min. brightness) Also, how do I set the screen timeout to ten seconds? gconf editor isn't honoring it when I set it to that. Will switching from nVidia to Nouveau save any significant amount of power?

    Read the article

  • Both screens always stay on after adding second monitor

    - by J.Merrill
    I had a single 1920x1080 monitor on a Windows 7 desktop PC and, per "power management" (not screen saver), the screen would go blank after 10 minutes. I added another monitor (2560x1600 if that matters) and since then, neither screen has ever blanked. I've tried turning on the "blank" screen saver, but that didn't help either -- I can go away for hours and when I come back, both screens are on. I've seen others with similar issues apparently caused by e.g. wireless mice that seem to move infinitesimally, but I've got the same wired mouse I had before. I can't understand why neither the screen saver nor power management is doing what it should to blank the screens, when "power management" used to do it when there was only one monitor. Maybe it doesn't matter so much with current LCD display technology (no "burn in") but doesn't a monitor use more power when "power management" hasn't turned off the display? Thanks for any suggestions.

    Read the article

  • Best way to choose random element from weighted list

    - by Qqwy
    I want to create a simple game. Every so often, a power up should appear. Right now the different kinds of power ups are stored in an array. However, not every power up should appear equally often: For instance, a score multiplier should appear much more often than an extra life. What is the best/fastest way to pick an element at random from a list where some of the elements should be picked more often than others?

    Read the article

  • Does a c/c++ compiler optimize constant divisions by power-of-two value into shifts?

    - by porgarmingduod
    Question says it all. Does anyone know if the following... size_t div(size_t value) { const size_t x = 64; return value / x; } ...is optimized into? size_t div(size_t value) { return value >> 6; } Do compilers do this? (My interest lies in GCC). Are there situations where it does and others where it doesn't? I would really like to know, because every time I write a division that could be optimized like this I spend some mental energy wondering about whether precious nothings of a second is wasted doing a division where a shift would suffice.

    Read the article

  • how to calculate power consumption on an Android mobile that uses wifi?

    - by Marco
    Hello, I have implemented a routing protocol on an Android 1.6 mobile that uses wireless (ad-hoc) network in order to exchange messages. Now I would like to evaluate it under an energy consumption point of view, the base would be to try to calculate the energy wasted to transmit a single packet, do anybody has any idea how to do that? Software/hardware solutions are welcome! Thanx :)

    Read the article

  • C# log base 10 and rounding up to nearest power of 10?

    - by Tom
    Hi, if i have a number between 100 and 1000 i want to get the value 3 because 10^3 = 1000. Likewise, if i had a number between 10 and 100 i would want to get the value 2, because 10^2 is 100. Incase you're wondering, its to do with calculating a probability and i always need to divide through by 10^value, to keep the probability between 0 and 1. For example if i calculate 9256, i need to divide through by 10^4, so that i get a probability of 0.92 I'm not sure how to do the rounding up and how to do the base 10, could someone please help?

    Read the article

  • How would I go about updating my electronic circuit simulator's 'electricity'?

    - by liqwidice
    I have made an application which allows the user to place down wires, power sources, and inverters on a virtual circuit board. All connections between tiles are automatic, as shown here: As you can see in the last image, the updating of power throughout this grid is not yet functioning. I think I understand how to do this updating conceptually, but getting it to work in my program is appearing to be much more difficult than I first imagined. My source code can be found here. If you have any tips as to how to I might approach this monstrous task, please let me know. EDIT The goal here is to simply get a working application. Getting tiles to pass on power to their neighbors is quite easy, but the tricky part is getting wires to "unpower" after the removal of a power source. The size of the grid is just 18x18, so efficiency really isn't a factor, for those wondering.

    Read the article

< Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >