Search Results

Search found 14983 results on 600 pages for 'zorin os'.

Page 580/600 | < Previous Page | 576 577 578 579 580 581 582 583 584 585 586 587  | Next Page >

• XFS disk becomes unavailable after a while

  - by Guard

  Ubuntu 12.04 (but the same was on 11.10 before upgrading) WD MyBook, 2TB, no RAID (or RAID0, not completely sure, anyway no mirroring, both 1TB disks are in use, mounted as a single device). Formatted to XFS, normally used for big movie files. Connected to Firewire 800. At some point the LED started going up and down as when constantly reading/writing. The device gives access error. When unplugged (cable, then holding the power button for a while, then unplugging the power) and re-connected becomes available. xfs_check with no results. xfs_repair did something, but looks like didn't fix any error. Then after a massive read (checking 1.5GB torrent file for integrity) becomes unavailable again. Any ideas what's wrong? Drives? Cables? Motherboard? OS? UPD: not sure how relevant this is, but here are dmesg output [14380.632816] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled [14380.633356] SGI XFS Quota Management subsystem [14421.812220] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14441.890596] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14441.896858] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14453.895347] firewire_core: created device fw1: GUID 0090a99500a35518, S400, 9 config ROM retries [14453.904818] scsi6 : SBP-2 IEEE-1394 [14453.905014] scsi7 : SBP-2 IEEE-1394 [14454.139993] firewire_sbp2: fw1.0: logged in to LUN 0000 (0 retries) [14454.158769] scsi 6:0:0:0: Direct-Access WD My Book 1015 PQ: 0 ANSI: 4 [14454.159251] sd 6:0:0:0: Attached scsi generic sg3 type 0 [14454.162391] firewire_sbp2: fw1.1: logged in to LUN 0001 (0 retries) [14454.167453] sd 6:0:0:0: [sdc] 3907017568 512-byte logical blocks: (2.00 TB/1.81 TiB) [14454.178822] sd 6:0:0:0: [sdc] Write Protect is off [14454.178826] sd 6:0:0:0: [sdc] Mode Sense: 10 00 00 00 [14454.186830] scsi 7:0:0:1: Enclosure WD My Book Device 1015 PQ: 0 ANSI: 4 [14454.186995] scsi 7:0:0:1: Attached scsi generic sg4 type 13 [14454.190078] sd 6:0:0:0: [sdc] Cache data unavailable [14454.190087] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.202176] sd 6:0:0:0: [sdc] Cache data unavailable [14454.202185] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.239940] sdc: [mac] sdc1 sdc2 sdc3 sdc4 [14454.271262] sd 6:0:0:0: [sdc] Cache data unavailable [14454.271270] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.271354] sd 6:0:0:0: [sdc] Attached SCSI disk [14454.272149] ses 7:0:0:1: Attached Enclosure device [14606.090024] XFS (sdc3): Mounting Filesystem [14612.048343] XFS (sdc3): Starting recovery (logdev: internal) [14620.697636] XFS (sdc3): Ending recovery (logdev: internal) [14748.120957] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx [14748.120963] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO [14752.568382] uhci_hcd 0000:00:1a.0: PCI INT A disabled [14752.568579] uhci_hcd 0000:00:1a.1: PCI INT B disabled [14752.568738] ehci_hcd 0000:00:1a.7: PCI INT C disabled [14752.568779] ehci_hcd 0000:00:1a.7: PME# enabled [14752.584526] uhci_hcd 0000:00:1d.1: PCI INT B disabled [14752.584689] uhci_hcd 0000:00:1d.2: PCI INT C disabled [14752.680079] ehci_hcd 0000:00:1a.7: BAR 0: set to [mem 0xe4641000-0xe46413ff] (PCI address [0xe4641000-0xe46413ff]) [14752.680104] ehci_hcd 0000:00:1a.7: restoring config space at offset 0xf (was 0x300, writing 0x30b) [14752.680136] ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002) [14752.680170] ehci_hcd 0000:00:1a.7: PME# disabled [14752.680182] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [14752.680190] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [14752.710334] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [14752.710342] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [14752.749186] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [14752.749194] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [14752.790231] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22 [14752.790239] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [14752.829170] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [14752.829178] uhci_hcd 0000:00:1d.2: setting latency timer to 64

  Read the article

• iPhone doesn't save password for Cisco IPsec VPN using racoon daemon

  - by dsx

  On my Debian server I had set up racoon daemon (1:0.8.0-14) for Cisco IPSec VPN using certificates for authentication. My racoon.conf is like following: log info; path certificate "/etc/racoon/certs"; listen { isakmp $SERVER_IP_HERE [500]; isakmp_natt $SERVER_IP_HERE [4500]; } timer { natt_keepalive 10 sec; } remote anonymous { lifetime time 24 hours; proposal_check obey; passive on; exchange_mode aggressive,main; my_identifier asn1dn; peers_identifier asn1dn; verify_identifier on; certificate_type x509 "cert_name.crt" "key_name.key"; ca_type x509 "ca.crt"; mode_cfg on; verify_cert on; ike_frag on; generate_policy on; nat_traversal on; dpd_delay 20; proposal { encryption_algorithm aes; hash_algorithm sha1; authentication_method xauth_rsa_server; dh_group modp1024; } } mode_cfg { conf_source local; auth_source system; auth_throttle 3; save_passwd on; dns4 8.8.8.8; network4 $SOME_LAN_SUBNET; netmask4 255.255.255.0; pool_size 128; } sainfo anonymous { pfs_group 2; lifetime time 24 hour; encryption_algorithm aes; authentication_algorithm hmac_sha1; compression_algorithm deflate; } I'm not using PSK authentication here. Using iPhone configuration utility I had uploaded all required certificates to iPhone and set up VPN on demand. Everything works just fine except one thing: iPhone refuses to save VPN password regardless of save_passwd on; in racoon configuration file. As opposed to iPhone behaviour, Mac OS X 10.8.2 have no problems saving password. I had examined iPhone log file and found following: racoon[151] <Notice>: >>>>> phase change status = phase 1 established configd[50] <Notice>: IPSec Network Configuration started. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-ADDRESS = $SUBNET_IP_HERE. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-MASK = 255.255.255.0. configd[50] <Notice>: IPSec Network Configuration: SAVE-PASSWORD = 0. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-DNS = 8.8.8.8. configd[50] <Notice>: IPSec Network Configuration: BANNER = . configd[50] <Notice>: IPSec Network Configuration: DEF-DOMAIN = . configd[50] <Notice>: IPSec Network Configuration: DEFAULT-ROUTE = local-address $SUBNET_IP_HERE/32. configd[50] <Notice>: IPSec Phase2 starting. configd[50] <Notice>: IPSec Network Configuration established. configd[50] <Notice>: IPSec Phase1 established. Please note IPSec Network Configuration message containing SAVE-PASSWORD = 0.. Is it a bug in racoon daemon on server, or iPhone (iOS version is 6.0.1 (10A523)) or it is me missing something? How to make iPhone remember IPSec VPN password?

  Read the article

• what is the best mid/high-end class audio/music creation audio sound card?

  - by Chris

  Hello, I have a computershop myself, and I repair computers. But one of the things I really don't know (yet) is the performace od audio cards for music creation with midi. I have searched and searched and came up with some good reviews, but after browsing for a couple of hours I could't see the trees trough the forrest :-D (it's a dutch expression) At one moment I thought the M-Audio - Delta 1010LT would be a good PCIe card, later on I read that this card was released years ago. (but that could be false information) Also any personal expierence would be great, but not necessairy. I have searched a few cards, and I hope someone can help me make a choice for a friend of mine. He's buget is between $100 and $350 I know there are audio cards from $ 500 - $1850,- this is just too expensive. The following specs are crucial: ASIO Midi Mic in minimal 5.1, 7.1 recommended it's not for airplay, but just to compose music at home. using Ableton and midi keyboard. 1. M-Audio - Delta 1010LT: 8 x 8 analog I/O 2 mic preamps or line inputs S/PDIF digital I/O (coaxial) with 2-channel PCM SCMS copy protection control digital I/O supports surround-encoded AC-3 and DTS pass-through 1 x 1 MIDI I/O directly drive up to 7.1 surround (bass management software included) software controlled 36-bit internal DSP digital mixing/routing +4dbu/-10dBV operation individually switched in software word clock I/O for sample accurate device synchronization 2. RME HDSP 9632: * Stereo Analog Ein- und Ausgang, symmetrisch*, 24-Bit/192kHz, > 110 dB SNR * Optionale Erweiterungsboards mit je 4 symmetrischen Ein- und Ausgängen * Alle analogen I/Os voll 192 kHz-fähig, also keine Reduzierung der Kanalzahl * 1 x ADAT Digital In/Out, 96 kHz-fähig (S/MUX) * 1 x SPDIF Digital In/Out, 192 kHz-fähig * 1 x Breakout Kabel für koaxialen SPDIF-Betrieb* * Also bis zu 16 Ein-und Ausgänge gleichzeitig nutzbar! * 1 x Stereo Kopfhörerausgang, parallel zum analogen Ausgang, aber eigene Pegelanpassung * 1 x MIDI I/O für 16 Kanäle Hi-Speed MIDI über Breakout Kabel * DIGICheck, RMEs einzigartiges Meter- und Analysetool mit Spectral Analyser, Professionelle Level Meter 2/8/16-Kanalig, Vector Audio Scope und diversen weiteren Analysefunktionen * HDSP Meter Bridge: Frei skalierbare Levelmeter mit Peak- und RMS Berechnung in Hardware * TotalMix: 512-Kanal Mischer mit 40 Bit interner Auflösung 3. EMU 1212M (1212 M) PCIe: * Top kwaliteit convertors 24-bit/192kHz convertors. * Hardware gestuurde effecten. * DSP zero-latency hardware mixen en monitoring. * Analoge en digitale I/O plus MIDI. * EMU Production Tools Software Bundle - Cakewalk SONAR , Steinberg Cubase LE, Ableton Live E-MU Edition **EMU 1212M PCI-e inputs/outputs:** * 2 balanced jack inputs. * 2 balanced jack outputs. * 24-bit/192kHz ADAT I/O. * 24-bit/192kHz Coaxiale S/PDif I/O switchable to AES/EBU. * MIDI I/O. 4. M-Audio Audiophile 192: - Up to 24-bit/192kHz audio - 2 balanced analog inputs (1/4” TRS) - 2 balanced analog outputs (1/4” TRS) - S/PDIF digital I/O (coaxial RCA connectors) with 2-channel PCM - SCMS copy protection control - Digital I/O supports surround-encoded AC-3 and DTS pass-through - Direct hardware input monitoring via separate balanced 1/4” TRS monitor outputs - Software routing of inputs and outputs - Digital I/O can be routed to/from external effects - 16-channel MIDI I/O - ASIO, WDM, GSIF 2 and Core Audio driver support for compatibility with most applications - 64-bit driver support for Windows - PCI 2.2 compatibility - Apple G5 compatible - Incompatible exceptions - Includes Ableton Live Lite music production software, so you can make music right away - Works with other Delta cards Technical Specifcations: - Compatibility - ASIO - WDM - GSIF 2 - Core Audio

  Read the article

• Alternative Methods of Sharing Folders in Windows?

  - by Blaenk

  Hey guys. I'm running Windows 7 and as of now I simply share folders as one usually does in Windows. I then have a MacBook with Leopard (Now Snow Leopard) which I use to connect to my computer to mount the shares by going to Finder, then CMD + K and typing smb://BlaenkPC (The name of my PC) into the address box. This consequently connects to my computer and mounts all of the shares. The problem is that sometimes, if for example I close my MacBook (Which makes it go to sleep) or sometimes even without doing that, the connection somehow drops. Sometimes I close the MacBook and upon re-opening it, everything still works; it's random. It still shows the computer as being connected, but it just shows 'loading' indefinitely. If I hit 'eject' with the intention of re-connecting to the computer, it disappears from the sidebar (The Computer Icon) in Finder, but I cannot re-connect. Activity Monitor (or ps aux, whichever) both show hung instances of umount; one for each share that was mounted. I cannot kill these processes with kill or killall (Yes, even with sudo, and sending signal -9). This has happened to me before, and here is another person who has experienced this. My question boils down to this: Is there an alternative method of sharing folders in Windows, that my Mac can read/understand, that is possibly more reliable and preferably just as fast? I usually use the mounted shares to watch television episodes off my computer, or movies, etc. (In other words, I open them in VLC and they automatically stream from my computer). As far as I can tell, this is a problem with the Samba protocol. I have heard of NFS, but I am not sure if I would have to re-format my drives, or what. I don't mind running a service or daemon to allow the sharing of the folders, I just want it to be done and hopefully in a better way than typical Windows shares through Samba. Usually when I encounter this problem, which is often (read: every day), I have no other option but to restart the MacBook. As I stated in the first question I linked to, shutting down and restarting don't work; I have to manually force the shutdown by holding the power button. I have not modified my installation of Mac OS X in any hackish way, so I doubt it's something with the Operating System, but worst come to worst, I might end up reformatting and doing a clean install to see if that fixes anything, as I am at a complete loss as to what may be causing the problem, and no one else seems to have any idea or care, despite there being quite a few people suffering from this problem, as my research has shown. Any pieces of information that can help are extremely appreciated. You don't have to answer every question on here, but maybe even some insight as to why it might not be possible to kill those hung umount instances for example, or why I may not be able to reconnect using samba (Is it something regarding the way the protocol works?). One thing to note is that I have another computer in the home network that doesn't seem to have this problem. However, it is also running Windows 7 (Note though that I am not using the homegroup feature, but the typical windows sharing feature). My only deduction is that the problem is being caused by the way the Mac (Or Samba implementation, whichever) is handling things. Perhaps it is a limitation.

  Read the article

• How do I configure Apache 2.2 to Run Background PHP Processes on Win 2003?

  - by Captain Obvious

  I have a script, testforeground.php, that kicks off a background script, testbackground.php, then returns while the background script continues to run until it's finished. Both the foreground and background scripts write to the output file correctly when I run the foreground script from the command line using php-cgi: C:\>php-cgi testforeground.php The above command starts a php-cgi.exe process, then a php-win.exe process, then closes the php-cgi.exe almost immediately, while the php-win.exe continues until it's finished. The same script runs correctly but does not have permission to write to the output file when I run it from the command line using plain php: C:\>php testforeground.php AND when I run the same script from the browser, instead of php-cgi.exe, a single cmd.exe process opens and closes almost instantly, only the foreground script writes to the output file, and it doesn't appear that the 2nd process starts: http://XXX/testforeground.php Here is the server info: OS: Win 2003 32-bit HTTP: Apache 2.2.11 PHP: 5.2.13 Loaded Modules: core mod_win32 mpm_winnt http_core mod_so mod_actions mod_alias mod_asis mod_auth_basic mod_authn_default mod_authn_file mod_authz_default mod_authz_groupfile mod_authz_host mod_authz_user mod_autoindex mod_cgi mod_dir mod_env mod_include mod_isapi mod_log_config mod_mime mod_negotiation mod_setenvif mod_userdir mod_php5 Here's the foreground script: <?php ini_set("display_errors",1); error_reporting(E_ALL); echo "<pre>loading page</pre>"; function run_background_process() { file_put_contents("0testprocesses.txt","foreground start time = " . time() . "\n"); echo "<pre> foreground start time = " . time() . "</pre>"; $command = "start /B \"{$_SERVER['CMS_PHP_HOMEPATH']}\php-cgi.exe\" {$_SERVER['CMS_HOMEPATH']}/testbackground.php"; $rp = popen($command, 'r'); if(isset($rp)) { pclose($rp); } echo "<pre> foreground end time = " . time() . "</pre>"; file_put_contents("0testprocesses.txt","foreground end time = " . time() . "\n", FILE_APPEND); return true; } echo "<pre>calling run_background_process</pre>"; $output = run_background_process(); echo "<pre>output = $output</pre>"; echo "<pre>end of page</pre>"; ?> And the background script: <?php $start = "background start time = " . time() . "\n"; file_put_contents("0testprocesses.txt",$start, FILE_APPEND); sleep(10); $end = "background end time = " . time() . "\n"; file_put_contents("0testprocesses.txt", $end, FILE_APPEND); ?> I've confirmed that the above scripts work correctly using Apache 2.2.3 on Linux. I'm sure I just need to change some Apache and/or PHP config settings, but I'm not sure which ones. I've been muddling over this for too long already, so any help would be appreciated.

  Read the article

• XenServer Converting HVM to Paravirtualised

  - by Karl Kloppenborg

  Recently I have been tasked with the daunting process of converting a setup of HVM enabled VMs (running on Citrix XenServer 5.6.0) into PV (paravirtualised) containers. The constraints of the project was that: The operating system must be functionally identical after the migration. minimal modification to the operating system (with exception of kernel / drive mapping) I also was allowed to change the bootloader(ie, grub) in what ever way I see fit. However, I have attempted this, I will firstly like to show you my steps I took. This at the moment is CentOS5.5 specific: Steps: yum install kernel-xen This installed: 2.6.18-194.32.1.el5xen edited: /boot/grub/menu.lst changed my specs to match: title CentOS (2.6.18-194.32.1.el5xen) root (hd0,0) kernel /vmlinuz-2.6.18-194.32.1.el5xen ro root=/dev/VolGroup00/LogVol00 console=xvc0 initrd /initrd-2.6.18-194.32.1.el5xen.img Then I changed my xenserver parameters to match: xe vm-param-set uuid=[vm uuid] PV-bootloader-args="--kernel /vmlinuz-2.6.18-194.32.1.el5xen --ramdisk /initrd-2.6.18-194.32.1.el5xen.img" xe vm-param-set uuid=[vm uuid] HVM-boot-policy="" xe vm-param-set uuid=[vm uuid] PV-bootloader=pygrub xe vbd-param-set uuid==[Virtual Block Device/VBD uuid] bootable=true Some things to note, I am running a VolGroup LVM ;) Anyways, after all these steps (which aren't much!) I boot the VM and it boots initial kernel just fine, however I am presented with this error: Boot Screen: device-mapper: dm-raid45: initialized v0.2594l Waiting for driver initialization. Scanning and configuring dmraid supported devices Scanning logical volumes Reading all physical volumes. This may take a while... Activating logical volumes Volume group "VolGroup00" not found Creating root device. Mounting root filesystem. mount: could not find filesystem '/dev/root' Setting up other filesystems. Setting up new root fs setuproot: moving /dev failed: No such file or directory no fstab.sys, mounting internal defaults setuproot: error mounting /proc: No such file or directory setuproot: error mounting /sys: No such file or directory Switching to new root and running init. unmounting old /dev unmounting old /proc unmounting old /sys switchroot: mount failed: No such file or directory Now my hints are that it cannot detect / because of the fact that when you change from HVM mode to PV it does something (not that obvious) When you make a SR (storage) on a HVM, you get it mounted to the guest os as /dev/hda. However in PV mode, this presents itself as /dev/xvda... Could this be the answer? and if so, how the heck to I implement it?? Update: So I have gotten a bit further in my quest, as it now detects the LVM's... To do this, I required to recompile the xen-kernel initrd image. Command: mkinitrd -v --builtin=xen_vbd --preload=xenblk initrd-2.6.18-194.32.1.el5xen.img 2.6.18-194.32.1.el5xen Now when I boot I get this: Boot Screen: Loading dm-raid45.ko module device-mapper: dm-raid45: initialized v0.2594l Scanning and configuring dmraid supported devices Scanning logical volumes Reading all physical volumes. This may take a while... Found volume group "VolGroup00" using metadata type lvm2 Activating logical volumes 3 logical volume(s) in volume group "VolGroup00" now active Creating root device. Mounting root filesystem. mount: error mounting /dev/root on /sysroot as ext3: Device or resource busy Setting up other filesystems. Setting up new root fs setuproot: moving /dev failed: No such file or directory no fstab.sys, mounting internal defaults setuproot: error mounting /proc: No such file or directory setuproot: error mounting /sys: No such file or directory Switching to new root and running init. unmounting old /dev unmounting old /proc unmounting old /sys switchroot: mount failed: No such file or directory Kernel panic - not syncing: Attempted to kill init!

  Read the article

• SmartOS reboots spontaneously

  - by Alex

  I run a SmartOS system on a Hetzner EX4S (Intel Core i7-2600, 32G RAM, 2x3Tb SATA HDD). There are six virtual machines on the host: [root@10-bf-48-7f-e7-03 ~]# vmadm list UUID TYPE RAM STATE ALIAS d2223467-bbe5-4b81-a9d1-439e9a66d43f KVM 512 running xxxx1 5f36358f-68fa-4351-b66f-830484b9a6ee KVM 1024 running xxxx2 d570e9ac-9eac-4e4f-8fda-2b1d721c8358 OS 1024 running xxxx3 ef88979e-fb7f-460c-bf56-905755e0a399 KVM 1024 running xxxx4 d8e06def-c9c9-4d17-b975-47dd4836f962 KVM 4096 running xxxx5 4b06fe88-db6e-4cf3-aadd-e1006ada7188 KVM 9216 running xxxx5 [root@10-bf-48-7f-e7-03 ~]# The host reboots several times a week with no crash dump in /var/crash and no messages in the /var/adm/messages log. Basically /var/adm/messages looks like there was a hard reset: 2012-11-23T08:54:43.210625+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T09:14:43.187589+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T09:34:43.165100+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T09:54:43.142065+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T10:14:43.119365+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T10:34:43.096351+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T10:54:43.073821+00:00 10-bf-48-7f-e7-03 rsyslogd: -- MARK -- 2012-11-23T10:57:55.610954+00:00 10-bf-48-7f-e7-03 genunix: [ID 540533 kern.notice] #015SunOS Release 5.11 Version joyent_20121018T224723Z 64-bit 2012-11-23T10:57:55.610962+00:00 10-bf-48-7f-e7-03 genunix: [ID 299592 kern.notice] Copyright (c) 2010-2012, Joyent Inc. All rights reserved. 2012-11-23T10:57:55.610967+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: lgpg 2012-11-23T10:57:55.610971+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: tsc 2012-11-23T10:57:55.610974+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: msr 2012-11-23T10:57:55.610978+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: mtrr 2012-11-23T10:57:55.610981+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: pge 2012-11-23T10:57:55.610984+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: de 2012-11-23T10:57:55.610987+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: cmov 2012-11-23T10:57:55.610995+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: mmx 2012-11-23T10:57:55.611000+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: mca 2012-11-23T10:57:55.611004+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: pae 2012-11-23T10:57:55.611008+00:00 10-bf-48-7f-e7-03 unix: [ID 223955 kern.info] x86_feature: cv8 The problem is that sometimes the host loses the network interface on reboot so we need to perform a manual hardware reset to bring it back. We do not have physical or virtual access to the server console - no KVM, no iLO or anything like this. So, the only way to debug is to analyze crash dumps/log files. I am not a SmartOS/Solaris expert so I am not sure how to proceed. Is there any equivalent of Linux netconsole for SmartOS? Can I just redirect the console output to the network port somehow? Maybe I am missing something obvious and crash information is located somewhere else.

  Read the article

• Cannot open simple script application on mac

  - by streetpc

  Mac OS X 10.6 I created a very simple app, which is only a wrapper of a shell script (so that I can select this script in application selectors, like startup apps). I try to launch it and yesterday it worked, but today I changed the executable script's content and name (with something that perfeclty works in a shell script launched in the Terminal) and it will only display a Finder-iconed dialog saying Cannot open the application because it is not supported on this kind of Mac. I restored the previous script (content/name) but I still get the error! Same when re-bundling the app from scratch, or completely changing the bundle identifier… If I try to open it in the Terminal using open My.app, I get The application cannot be opened because it has an incorrect executable format. But when I executes directly the Contents/MacOS/Script, it allways works (iwth both contents). Also, it is displayed with correct icon and meta-information in the Finder (so I guess the Info.plist is understood). The app's file tree is: Contents/ Info.plist MacOS/ Script (executable bit set, works when launched directly) PkgInfo Resources/ AppIcon.icns Here is the Info.plist content: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>CFBundleExecutable</key> <string>Script</string> <key>CFBundleIconFile</key> <string>AppIcon</string> <key>CFBundleIdentifier</key> <string>asdf.ScriptApp</string> <key>CFBundleInfoDictionaryVersion</key> <string>6.0</string> <key>CFBundleName</key> <string>My script</string> <key>CFBundlePackageType</key> <string>APPL</string> <key>CFBundleShortVersionString</key> <string>1.0</string> <key>CFBundleSignature</key> <string>????</string> <key>CFBundleVersion</key> <string>1</string> <key>LSMinimumSystemVersion</key> <string>10.4</string> </dict> </plist> And the PkgInfo file only contains APPL????. I tested the Script with a simple echo "ok" and echo "ok" >/tmp/test (plus #!/bin/sh header). So my questions are: Is there some kind of validity caching for applications ? based on what ? how do I flush it ? Where does this message come from ? I tried to google it but all I get is a page talking about 32/64 bits Java…

  Read the article

• iCloud stuff stops working while connected to OpenVPN

  - by Taco Bob

  I have a fairly simple OpenVPN setup on an OpenVZ VPS with Ubuntu 11.10. Client is the Viscosity client on Mac OS X 10.8.2, and after some testing, we can rule out the client as being part of the problem. Everything has been working fine except for Apple's iCloud stuff. Web surfing, email, FTP, NNTP, and Skype are all working as expected. It's ONLY the iCloud services that cease to function. If I connect to the VPN, iCloud stuff stops working. I no longer get anything in Messages, Calendar items don't get updated, and Notifications stop working. If I disconnect, the iCloud stuff all starts working. Connect again, iCloud stops working. Here's the server.conf: status openvpn-status.log log /var/log/openvpn.log verb 4 port 1194 proto udp dev tun ca /etc/openvpn/ca.crt cert /etc/openvpn/server.crt key /etc/openvpn/server.key dh /etc/openvpn/dh1024.pem server 10.9.8.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1" push “dhcp-option DNS 10.9.8.1? keepalive 10 120 duplicate-cn cipher BF-CBC comp-lzo user nobody group nogroup persist-key persist-tun tun-mtu 1500 mssfix 1400 I'm using iptables in a script, and it's also fairly simplistic. iptables -F iptables -t nat -F iptables -t mangle -F iptables -A FORWARD -i tun0 -o venet0 -j ACCEPT iptables -A FORWARD -i venet0 -o tun0 -j ACCEPT iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A INPUT -p tcp --dport 1194 -j ACCEPT iptables -A INPUT -p udp --dport 1194 -j ACCEPT iptables -t nat -A POSTROUTING -s 10.9.8.0/24 -j SNAT --to-source <server's public ip> echo 1 > /proc/sys/net/ipv4/ip_forward I tried forwarding ports as well, with no success. iptables -A FORWARD -p tcp -d 10.9.8.0/24 --dport 5222:5230 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 5222:5230 -j DNAT --to-destination 10.9.8.6 I am also sometimes behind a double-NAT situation that I have no control over. Client -> work VPN -> my OpenVPN box -> Internet. Client -> Airport Express -> ISP (which is doing NAT) -> my OpenVPN box -> Internet. Those two situations are just the fact of life where I am, and I cannot change them. I do have full control over my client and the OpenVPN server. I am completely out of ideas. I have posted a similar query at the OpenVPN forums, but it hasn't posted yet and seems to be in their moderation queue still. Tried on freenode irc channels, but nobody is awake, so here I am. I have Googled extensively for this, and can find nothing that is related. Help me get iCloud stuff working again! (I tried serverfault, it was closed as off-topic. I'm trying here and the Unix site as well. Here because it's a more general audience that might know more about OpenVPN based on the number of questions I see asked about it) EDIT: -I have also tried upgrading to Version: 2.3-beta1-debian0 - issue persists. -Removed all iptables rules except for the ones that flush -left this rule:iptables -t nat -A POSTROUTING -s 10.9.8.0/24 -j SNAT --to-source (server ip) -added iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT still, nothing works. I can see traffic in tcpdump on the server if i watch the tunnel: 20:03:48.702835 IP nk11p01st-courier105-bz.push.apple.com.5223 10.9.8.6.60772: Flags [F.], seq 2635, ack 1218, win 76, options [nop,nop,TS val 914984811 ecr 745921298], length 0 20:03:48.911244 IP 10.9.8.6.60772 nk11p01st-courier105-bz.push.apple.com.5223: Flags [R], seq 3621143451, win 0, length 0 But still, no push messages/notifications are ever delivered. :/ EDIT: * Further testing indicates that it might actually be the client after all.

  Read the article

• Hanging of host network connections when starting KVM guest on bridge

  - by Chris Phillips

  Hi, I've a KVM system upon which I'm running a network bridge directly between all VM's and a bond0 (eth0, eth1) on the host OS. As such, all machines are presented on the same subnet, available outside of the box. The bond is doing mode 1 active / passive, with an arp_ip_target set to the default gateway, which has caused some issues in itself, but I can't see the bond configs mattering here myself. I'm seeing odd things most times when I stop and start a guest on the platform, in that on the host I lose network connectivity (icmp, ssh) for about 30 seconds. I don't lose connectivity on the other already running VM's though... they can always ping the default GW, but the host can't. I say "about 30 seconds" but from some tests it actually seems to be 28 seconds usually (or at least, I lose 28 pings...) and I'm wondering if this somehow relates to the bridge config. I'm not running STP on the bridge at all, and the forwarding delay is set to 1 second, path cost on the bond0 lowered to 10 and port priority of bond0 also lowered to 1. As such I don't think that the bridge should ever be able to think that bond0 is not connected just fine (as continued guest connectivity implies) yet the IP of the host, which is on the bridge device (... could that matter?? ) becomes unreachable. I'm fairly sure it's about the bridged networking, but at the same time as this happens when a VM is started there are clearly loads of other things also happening so maybe I'm way off the mark. Lack of connectivity: # ping 10.20.11.254 PING 10.20.11.254 (10.20.11.254) 56(84) bytes of data. 64 bytes from 10.20.11.254: icmp_seq=1 ttl=255 time=0.921 ms 64 bytes from 10.20.11.254: icmp_seq=2 ttl=255 time=0.541 ms type=1700 audit(1293462808.589:325): dev=vnet6 prom=256 old_prom=0 auid=42949672 95 ses=4294967295 type=1700 audit(1293462808.604:326): dev=vnet7 prom=256 old_prom=0 auid=42949672 95 ses=4294967295 type=1700 audit(1293462808.618:327): dev=vnet8 prom=256 old_prom=0 auid=42949672 95 ses=4294967295 kvm: 14116: cpu0 unimplemented perfctr wrmsr: 0x186 data 0x130079 kvm: 14116: cpu0 unimplemented perfctr wrmsr: 0xc1 data 0xffdd694a kvm: 14116: cpu0 unimplemented perfctr wrmsr: 0x186 data 0x530079 64 bytes from 10.20.11.254: icmp_seq=30 ttl=255 time=0.514 ms 64 bytes from 10.20.11.254: icmp_seq=31 ttl=255 time=0.551 ms 64 bytes from 10.20.11.254: icmp_seq=32 ttl=255 time=0.437 ms 64 bytes from 10.20.11.254: icmp_seq=33 ttl=255 time=0.392 ms brctl output of relevant bridge: # brctl showstp brdev brdev bridge id 8000.b2e1378d1396 designated root 8000.b2e1378d1396 root port 0 path cost 0 max age 19.99 bridge max age 19.99 hello time 1.99 bridge hello time 1.99 forward delay 0.99 bridge forward delay 0.99 ageing time 299.95 hello timer 0.50 tcn timer 0.00 topology change timer 0.00 gc timer 0.04 flags vnet5 (3) port id 8003 state forwarding designated root 8000.b2e1378d1396 path cost 100 designated bridge 8000.b2e1378d1396 message age timer 0.00 designated port 8003 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags vnet0 (2) port id 8002 state forwarding designated root 8000.b2e1378d1396 path cost 100 designated bridge 8000.b2e1378d1396 message age timer 0.00 designated port 8002 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags bond0 (1) port id 0001 state forwarding designated root 8000.b2e1378d1396 path cost 10 designated bridge 8000.b2e1378d1396 message age timer 0.00 designated port 0001 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags I do see the new port listed as learning, but in line with the forward delay, only for 1 or 2 seconds when polling the brctl output on a loop. All pointers, tips or stabs in the dark appreciated.

  Read the article

• What NAS setup for two-way syncing over the internet?

  - by Jamse

  I have family living a few hours away and have a lot of files that I would like to share - especially lots of folders of digital photos, but also documents etc. - partially so they can see them, partially so I can have access when I visit them and partially for backup / redundancy purposes. My current hard drives on my main machine are getting pretty full anyway, and I have a MythTV box where my music is currently stored, so I was thinking of getting a NAS anyway. And at the other end my family have a few computers, so they would probably benefit from a NAS too. My general idea (though I'm willing to shift on this if there are any bright ideas about other ways of achieving my objectives) is to get a matching pair of NASs and have them sync over the internet. (To cut down on bandwidth use I would get them in sync locally to start with.) Having read around as best I can it seems that syncing over the internet is generally only a feature on quite high end units. However, I have seen that QNAP seem to feature this on their TS-110 and TS-210 units, which might work (they call it "remote replication"). They seem pretty reasonably priced for what they are, but of course with buying 2 of them and then adding the drives (say 1TB or 2TB each) I'd be looking at about £400 total. So, I'm looking for recommendations really. I don't want to spend more than the QNAPs would cost me, but any other ideas would be most appreciated. I am comfortable with technology and tinkering around, but I don't have as much time for that as I would like, so I guess I would favour solutions that require less tinkering rather than more (even though that's less fun!). Any thoughts would be welcome, as would any comments from people who have used the QNAP boxes for this. Thanks in advance. Some specifications: Two-way syncing. Changes made at either end should be synced to the other. There shouldn't be one unit that is effectively a read-only mirror of the other. Not real time. The syncing doesn't need to be real time - if it updated, say, daily overnight that would be fine. Set and forget. I would prefer minimal user interaction once set up - it would be great if syncs were scheduled and automatic. OS independence. I am running Windows XP plus an Ubuntu-based MythTV box. At the other end there are Windows 7 and Windows XP machines, plus a networked TV set top box which I think can play files off the network. Machine independence. I would favour a system that is self-contained, i.e. not reliant on any particular PC being switched on. If the system had enough else going for it I could perhaps work around it at this end, where I only have one PC that's used as such, but it would be harder at the other where there are at least two PCs that might be accessing the files. Notifications. I guess things like getting an email notification if the syncing fell over for any reason would be useful, though it's not a deal breaker. Update I've been digging some more and it looks like QNAP's Remote Replication function is actually just Rsync, so only really suitable for one-way syncing. I've posted on their forum to double check, but I think that's the case. In which case, I think the focus of my question is now either: do any reasonably-priced NASs support bidirectional syncing over the internet?, or has anyone had any luck installing onto NASs for this purpose? (Also, updated question to clarify that I'm after two-way syncing.)

  Read the article

• Installation of Access Database Engine 32-bit Fails

  - by Rayzor78

  I am trying to install Access Database Engine 2007 32-bit. The splash screen comes up, you click "Next", then it fails with the error: Installation ended prematurely because of an error You click "OK" and another error window says: The installation of the package failed. The exact same situation happens when I try this with Access Database Engine 2010 32-bit. This production server is running Windows Server 2008 R2 SP1 64-bit. Before I tried installing Access Database Engine 32-bit, I first needed to install Microsoft Office 2010 Pro (Excel and Office Tools only). I tried the 32-bit version on the production server since that is how I set it up in our Dev environment. No luck. The 32-bit version would not install. I did NOT get the error "You have 64-bit components of Office installed". I simply received the exact same two errors listed above. So, I knew that 32-bit/64-bit did not really matter for the Office install for my project, so I installed 64-bit of Office Pro 2010 (Excel and Office Tools only) with no problems. I have a requirement that I need to have the 32-bit version of the Access Database Engine installed. 2007 or 2010, doesn't matter. I cannot use the 64-bit version of Access Database Engine 2010 because my SSIS package will not work with it. I require the 32-bit version. I've tried several steps to try to get it installed. I seriously think that the production server has some aversion to installing 32-bit applications. Here's what I've tried: Tried installing via command line with the "/passive" switch....no luck. Tried numerous iterations to copy the install file to the server (downloaded a fresh copy directly to the server, downloaded a fresh copy to my local machine then copied it over, copied it over zipped up) (http://social.msdn.microsoft.com/Forums/en-US/sqldataaccess/thread/efd3c1f0-07cd-45ca-a626-2dd0c7ac3e9f). Tried Method 1 from this link. Could not try Method 2 because it requires a server reboot and in my environment that requires a long change management process. I've verified that I am a local administrator on the server. (Evidence, I am able to install other applications (office 64-bit per above)). Verified that there are no other office products that should be blocking the installation. The fore-mentioned install of Excel 2010 64-bit was the first Office product installed on the server. VERY ODD: To test my theory that the production server does not like 32-bit applications, I installed something lightweight. I installed 7-Zip 32-bit on the production server with no problems whatsoever. Here are some things that I have not tried (i will follow-up once I do): Method 2 (as mentioned above). Requires a server reboot. Have not verified that the Dev and Production environments are 100% identical. I've done a cursory check and on the surface they appear to be the same (same OS and SP version). I need to do a deeper dive to be 100% certain. I had no problems in my Dev environment. In Dev, I installed Office 2010 Pro 64-bit (Excel & Office Tools only) then via command line w/ the "/passive" switch, installed Access Database Engine 2010 32-bit. I don't know what else to try. Any suggestions or comments?

  Read the article

• How to diagnose and solve an erratic "HDCP Support Required"?

  - by Jom Orgstrom

  I am playing a digital tv broadcast on Windows Media Center for Windows 7. I built this system so it works with HDCP, and in fact I have been able to watch tv and bluray before with this same computer. However, I suddenly started getting an "HDCP Support Required" error from WMC. The entire message is as follows: HDCP Support Required High-bandwidth Digital Content Protection (HDCP) may not be supported by the current video card. Use an HDCP-compliant display, video card, and video driver. Or, connect using an analog connection such as component or VGA. Relevant specs are: CPU: Ivy Bridge Core i7-3770 Motherboard: Asus P8H77-I Memory: 16GB DDR3-1600 Graphics: Radeon HD 7850 (Driver by AMD, version 8.982.0.0 built on 2012/07/27) Display: Acer P243w connected by HDMI Sound: Roland Quad-Capture (It complains even when I use the bundled VIA HD Audio) TV Tuner: I-O Data GV-MC7/HZ3 OS: Windows 7 Professional SP1, Windows Update enabled. All patched and up to date. As you can see, there is nothing weird or old about my setup. I am also not doing anything strange, not doing any overclocking, weird system changes and so on. One thing that does happen from time to time, is that the display goes black for a few seconds (sometimes when watching media contents, sometimes when just using photoshop or Visual Studio). This happened with my previous setup as well, so I'd be inclined to think it is a display or cable issue (apart from the BD drive, these are the only things I kept from my previous setup to this one). But being a digital transfer, as far as I know, these things either work or not. Never erratically or with decreased quality. The thing is that sometimes I can watch the TV, sometimes not. This happens with recorded programs as well, so it's not a per-program thing. Sometimes rebooting helps, sometimes it doesn't. Sometimes unplugging and plugging back the HDMI connector helps, sometimes it doesn't. Sometimes doing so doesn't even turn the screen back on, so I have to reboot. Unfortunately, WMC's error message is quite unhelpful. I'd like to know exactly where the problem is, so I can solve it. I don't want to buy a brand new display just to then find out it was a registry setting that was misconfigured. I've tried looking at the system event viewer, but these errors don't show up at all in there. Other people who have this problem seem to have a setup that is not HDCP compliant, so I turn to you guys here. Anybody knows how to diagnose this problem? Edit: So I got the Cyberlink Blu-ray disc advisor. I ran it and told me everything was okay, except for the Video Connection Type, which showed as "Digital (without HDCP)". I then proceeded to unplug the power cable from the monitor, plugged it in again, ran the tool again, and now it's "Digital (with HDCP)". Needless to say, I can watch my TV and recorded programs on WMP again. I'm guessing that at some point, something may be slightly wrong with the HDCP setup, and Windows decides to reset the entire content protection path (which leads to the screen blanking out). Usually the reset succeeds, but sometimes it doesn't, so Windows defaults to turning HDCP off. There's no way to turn it back on, except by doing a hard reset of the display. I really want to know what the exact error was, so I can fix it. Is it the cable? is it the display? is it the video card? the driver? Also, is there any other way to try and turn HDCP on again without having to hard reset the display? Oh, questions, questions...

  Read the article

• Can I make my drives visible and change their partition type without losing my data?

  - by user165408

  I have made a lot of mistakes and now I cannot see my hard disk nor I can start my operating system on my laptop. All my passwords and important files on my hdd without any backup. I followed this course of action Changed my hard disk partitions to dynamic just for getting 5th partition. (1st mistake) Decreased partitions to 4 again. Backed up operating system from 4th to 3rd partition with Norton Ghost. Booted from a live CD for Windows XP. Formatted 4th partition and moved my all important data from 1st and 2nd partitions to the 4th partition. Deleted 1st and 2nd partitions and got 1 partition from half of empty space. So I have just 3 partitions and empty space between 1st and 2nd partitions. Tried to install Windows 8 to the first partition but it did not allow because it is dynamic. Also it did not allow to install to other partitions. Tried to install Windows XP to the 1st partition but it said if I continue I cannot use other drivers. Therefore I escaped from installing it. Booted from the Windows XP live CD then increased 1st partiton to less than 400mb of empty space. Therefore I thought it will be adjacent but it was shown as 2 partitions. In my computer I see just 3 drivers. Using Norton Ghost I recovered my OS to the 1st partition. (2nd mistake it was on 4th partition originally) Booted from a Windows XP live CD I tried to install bcdedit to the Windows XP live CD but it did not work. Then I tried to install EaseUS Partition Master Home Edition. It was installed with errors then I start it and it showed me an error like there is no hard disk. I looked to my PC and my drivers were not there. Booted from the Norton Ghost CD and it did not show me my drivers either, but before I was able to see them. I checked numbers of partition shown by the Norton Ghost utility and they are still have same numbers so I have to see my drivers but I cannot see them now. My hard disk is shown as extarnal dynamic now so I cannot see any drive in my PC in the live Windows XP. There are two options; first one is import extarnal disk and second one is convert disk to basic. Will they delete my data? I fear booting from CDs like Windows XP live CD, Norton Ghost CD, and the operating system CD/DVD, because they may overwrite a few MB their data to my data. These recover tools are already exist in Windows XP live CD by The Ultimate Boot CD for Windows. Can any of them help me? CompuAppa SwissKnife V3 DBXtract Disk Investigator Fab's AutoBackup 2.0 FileRecovery Floppy Repair Free Undelete Handy Recovery Recovery Manager Restorastion Restorastion Help File by UBCD4Win UnChk Unstoppable Copier Finally How can I make it so that my drives are visible again without losing my data? How can I convert my dynamic partitions to basic without losing my data?

  Read the article

• Hour-long shutdown duration "shutting down hyper-v virtual machine management service"

  - by icelava

  I have a Windows 2008 R2 server that is a Hyper-V host (Dell PowerEdge T300). Today for the first time I encountered an odd situation; i lost connection with one of the guest machines but logging on physically it seems the guest OS is still running but no longer contactable via the network. I tried to shut down the guest machine (Windows XP) but it would not shut down, getting stuck in a "Not responding" dialog box that cannot be dismissed. I used the Hyper-V management console to reset the machine and it could not get out of resetting state. I tried to save another Windows 2003 guest machine, and it would be progress with its Saving state (0%). The other running Windows 2003 guest was stuck in the logon dialog. My first suspicion is perhaps one of the Windows update patches this week (10 Nov 2011) may something to do with it, which was still pending a system restart. Well, since I could not do anything with Hyper-V i proceeded with the Windows Update restart, and now it is stuck half an hour at "Shutting down hyper-v virtual machine management service" Prior to restarting I did not observe any hard disk errors reported in the system event log; doubt it is a disk-related condition. Shall I force a hard reboot? UPDATE Ok so i left it hanging over an hour while attending to other matters, and thankfully the host cleanly restarted. I can operate the guest machines fine now. Phew. Hyper-V must have been crawling for some reason. The VMs have been observed to become slow in the past when the host has been up for a long duration (two weeks to a month), but never this slow. Would love to know what types of performance monitoring items i can observe to give a hint why this can happen. UPDATE 2012-02-13 In the months ever since, Hyper-V has stalled into this state another two times. It appears so randomly and without any error event logs to hint what is causing it enter this "drunkard" state. Just an Hyper-V management service timeout. Log Name: System Source: Service Control Manager Date: 13/2/2012 9:16:48 AM Event ID: 7043 Task Category: None Level: Error Keywords: Classic User: N/A Computer: elune Description: The Hyper-V Virtual Machine Management service did not shut down properly after receiving a preshutdown control. Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Service Control Manager" Guid="{555908d1-a6d7-4695-8e1e-26931d2012f4}" EventSourceName="Service Control Manager" /> <EventID Qualifiers="49152">7043</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8080000000000000</Keywords> <TimeCreated SystemTime="2012-02-13T01:16:48.882901900Z" /> <EventRecordID>567844</EventRecordID> <Correlation /> <Execution ProcessID="764" ThreadID="8484" /> <Channel>System</Channel> <Computer>elune</Computer> <Security /> </System> <EventData> <Data Name="param1">Hyper-V Virtual Machine Management</Data> </EventData> </Event> The only means out of it is to restart the system.

  Read the article

• What would cause Memcached to Hang for 2+ seconds?

  - by Brad Dwyer

  I'm going nuts trying to scale memcached. From their site: Memcached operations are almost all O(1). Connecting to it and issuing a get or stat command should never lag. If connecting lags, you may be hitting the max connections limit. See ServerMaint for details on stats to monitor. If issuing commands lags, you can have a number of tuning problems. Most common are hardware problems, not enough RAM (swapping), network problems (bandwidth, dropped packets, half-duplex connections). On rare occasion OS bugs or memcached bugs can contribute. Well.. it is most certainly not performing like an O(1) operation for me. Under low to normal load on our site memcached response times for get and set ops are about 0.001 seconds. Not bad. But if we triple the load we get outliers that take 100x (or in rare cases 1000x!) that long. I even had one instance where it took 2.2442 seconds for memcached to store a value. Obviously this is killing our site. Here's the output of Memcached-getStats during one of the slow periods: [pid] => 18079 [uptime] => 8903 [threads] => 4 [time] => 1332795759 [pointer_size] => 32 [rusage_user_seconds] => 26 [rusage_user_microseconds] => 503872 [rusage_system_seconds] => 125 [rusage_system_microseconds] => 477008 [curr_items] => 42099 [total_items] => 422500 [limit_maxbytes] => 943718400 [curr_connections] => 84 [total_connections] => 4946 [connection_structures] => 178 [bytes] => 7259957 [cmd_get] => 1679091 [cmd_set] => 351809 [get_hits] => 1662048 [get_misses] => 17043 [evictions] => 0 [bytes_read] => 109388476 [bytes_written] => 3187646458 [version] => 1.4.13 So things that I have ruled out so far are: Hitting the max connections limit (curr_connections of 84 is well below the default of max of 1024) Swapping - the machine has 900M out of 1024M of memory dedicated to memcached on a dedicated machine. It only appears to be using about 7MB of data as per the bytes stat. How would I diagnose the other hardware problems? prstat doesn't really show a whole lot going on in terms of CPU or memory usage. Not sure how to figure out the network problems but as this is a dedicated server on the same private network as the web box I don't think it's a connectivity issue (ping is less than a millisecond between the boxes). Is there something else I'm missing here? It's driving me nuts. Edit: Also forgot to mention that I've tried both persistent and non-persistent connections with minimal-to-no impact.

  Read the article

• How to change the language of driver interface for Canon Pixma printers?

  - by Sammy

  Is there a way to change the language of the driver interface for Canon Pixma printers? Which language is used seems to be determined by the language of the OS or the Windows localization settings. I really don't want that, I want to be able to set the language manually to my own liking, either during the driver installation or afterwards. I have found a workaround for Pixma IP2770 where you edit the setup.ini file by replacing the language names and the DLL search paths with <SELECT> under the LANGUAGES section. So instead of... 0000=<SELECT> 0001=Arabic,RES\STRING\IJInstAR.ini,RES\DLL\IJInstAR.dll 0804=Simplified Chinese,RES\STRING\IJInstCN.ini,RES\DLL\IJInstCN.dll 0404=Traditional Chinese,RES\STRING\IJInstTW.ini,RES\DLL\IJInstTW.dll 0005=Czech,RES\STRING\IJInstCZ.ini,RES\DLL\IJInstCZ.dll 0006=Danish,RES\STRING\IJInstDK.ini,RES\DLL\IJInstDK.dll 0007=German,RES\STRING\IJInstDE.ini,RES\DLL\IJInstDE.dll 0008=Greek,RES\STRING\IJInstGR.ini,RES\DLL\IJInstGR.dll 0009=English,RES\STRING\IJInstUS.ini,RES\DLL\IJInstUS.dll 000A=Spanish,RES\STRING\IJInstES.ini,RES\DLL\IJInstES.dll 000B=Finnish,RES\STRING\IJInstFI.ini,RES\DLL\IJInstFI.dll 000C=French,RES\STRING\IJInstFR.ini,RES\DLL\IJInstFR.dll 000E=Hungarian,RES\STRING\IJInstHU.ini,RES\DLL\IJInstHU.dll 0010=Italian,RES\STRING\IJInstIT.ini,RES\DLL\IJInstIT.dll 0011=Japanese,RES\STRING\IJInstJP.ini,RES\DLL\IJInstJP.dll 0012=Korean,RES\STRING\IJInstKR.ini,RES\DLL\IJInstKR.dll 0013=Dutch,RES\STRING\IJInstNL.ini,RES\DLL\IJInstNL.dll 0014=Norwegian,RES\STRING\IJInstNO.ini,RES\DLL\IJInstNO.dll 0015=Polish,RES\STRING\IJInstPL.ini,RES\DLL\IJInstPL.dll 0016=Portuguese,RES\STRING\IJInstPT.ini,RES\DLL\IJInstPT.dll 0019=Russian,RES\STRING\IJInstRU.ini,RES\DLL\IJInstRU.dll 001D=Swedish,RES\STRING\IJInstSE.ini,RES\DLL\IJInstSE.dll 001E=Thai,RES\STRING\IJInstTH.ini,RES\DLL\IJInstTH.dll 001F=Turkish,RES\STRING\IJInstTR.ini,RES\DLL\IJInstTR.dll 0021=Indonesian,RES\STRING\IJInstID.ini,RES\DLL\IJInstID.dll You get.... 0000=<SELECT> 0001=<SELECT> 0804=<SELECT> 0404=<SELECT> 0005=<SELECT> 0006=<SELECT> 0007=<SELECT> 0008=<SELECT> 0009=English,RES\STRING\IJInstUS.ini,RES\DLL\IJInstUS.dll 000A=<SELECT> 000B=<SELECT> 000C=<SELECT> 000E=<SELECT> 0010=<SELECT> 0011=<SELECT> 0012=<SELECT> 0013=<SELECT> 0014=<SELECT> 0015=<SELECT> 0016=<SELECT> 0019=<SELECT> 001D=<SELECT> 001E=<SELECT> 001F=<SELECT> 0021=<SELECT> .... in case English is the preferred language. It's a way to force the installation program to only install the English language support. IP2770 is a model for the Asian market, so if you want to check this out you need to go to the Canon India download page (for instance) to get the driver. Unfortunately this method is not possible with my IP4000. There is no driver even available for it to download for Windows Vista. But is there really no way of changing the language of the UI in any normal way, you know... without having to hack it? Besides, the driver for my printer comes with Windows Vista, so I don't even have to install any drivers. And little do I get the chance to set the language, knowing that the installation never happens. Any ideas?...

  Read the article

• RAID controller dropping the wrong drive

  - by bramp

  I've been having an issue with 3ware 9500S-8 RAID 10, and I have contracted their tech support, but I wanted to hear the serverfault community's recommendations. Firstly, all my data is backuped and secure, so I don't mind blowing my RAID away if I have to. But let me describe the problem I've been seeing. A month ago, disk 6 dropped out of the RAID. It is mirrored with disk 7, so I wasn't that bothered. I went to the data centre and replaced it. When I got back to the office, I noticed that disk 6 will still not in the RAID, and in fact the controller was show the name of the old drive still. A week later I went back and replace the drive again, thinking I might have swapped in a bad drive. Still the same problem. I decided to reboot the machine, to see if that would "force" the controller into seeing the new drive. It did, and a rebuild started to happen (from disk 7). Eventually both drives were showing as good. A week later, the MySQL database has flagged the database is corrupt, and is unable to repair it. I don't know what has gone wrong, but I suspected this 6-7 pair. At this point I noticed that the RAID had constantly been verifying itself, over and over. Regardless of this I began to rebuild the database, which took about 19 hours. It's a big database. Near the end of the repair, the RAID controller told me it had dropped disk 7, and that some data was most likely corrupted. I contacted LSI tech support, and they very promptly started to help me. I mentioned that drive 7 had been dropped. They suspect that drive 7 was always at fault, and drive 6 had always been good. I want to know how often a RAID controller would drop the wrong drive (in this case dropping drive 6 a month ago, instead of 7). I foolishly didn't run smartctl on the drives before I started swapping them out. I just assumed the RAID controller knew what it was talking about. I think my plan of action is to replace drive 7, rebuild the array from scratch, double check smartctl on ALL the disks, and then start restoring my data again. I would appreciate anyone's input on what the correct procedure for swapping drives is, and how often failures like this happen. If anyone would like more information then I'd be happy to provide it. thanks in advance. Oh some more information. I'm running CentOS 5.3, with two RAID arrays, a simple RAID 1 for the OS, and RAID 10 for the database. Both arrays are on different controllers. The RAID 10 is made of 10 identical ST3640323AS drives, until I swapped in a SAMSUNG HD103SJ last month.

  Read the article

• What NAS setup for syncing over the internet?

  - by Jamse

  I have family living a few hours away and have a lot of files that I would like to share - especially lots of folders of digital photos, but also documents etc. - partially so they can see them, partially so I can have access when I visit them and partially for backup / redundancy purposes. My current hard drives on my main machine are getting pretty full anyway, and I have a MythTV box where my music is currently stored, so I was thinking of getting a NAS anyway. And at the other end my family have a few computers, so they would probably benefit from a NAS too. My general idea (though I'm willing to shift on this if there are any bright ideas about other ways of achieving my objectives) is to get a matching pair of NASs and have them sync over the internet. (To cut down on bandwidth use I would get them in sync locally to start with.) Having read around as best I can it seems that syncing over the internet is generally only a feature on quite high end units. However, I have seen that QNAP seem to feature this on their TS-110 and TS-210 units, which might work (they call it "remote replication"). They seem pretty reasonably priced for what they are, but of course with buying 2 of them and then adding the drives (say 1TB or 2TB each) I'd be looking at about £400 total. So, I'm looking for recommendations really. I don't want to spend more than the QNAPs would cost me, but any other ideas would be most appreciated. I am comfortable with technology and tinkering around, but I don't have as much time for that as I would like, so I guess I would favour solutions that require less tinkering rather than more (even though that's less fun!). Any thoughts would be welcome, as would any comments from people who have used the QNAP boxes for this. Thanks in advance. Some specifications: Two-way syncing. Changes made at either end should be synced to the other. There shouldn't be one unit that is effectively a read-only mirror of the other. Not real time. The syncing doesn't need to be real time - if it updated, say, daily overnight that would be fine. Set and forget. I would prefer minimal user interaction once set up - it would be great if syncs were scheduled and automatic. OS independence. I am running Windows XP plus an Ubuntu-based MythTV box. At the other end there are Windows 7 and Windows XP machines, plus a networked TV set top box which I think can play files off the network. Machine independence. I would favour a system that is self-contained, i.e. not reliant on any particular PC being switched on. If the system had enough else going for it I could perhaps work around it at this end, where I only have one PC that's used as such, but it would be harder at the other where there are at least two PCs that might be accessing the files. Notifications. I guess things like getting an email notification if the syncing fell over for any reason would be useful, though it's not a deal breaker.

  Read the article

• What seems to be plaguing my hard drives?

  - by Craig

  In a little bit of a tech nightmare here. I know oodles about software, not so much more than the above average user about hardware. I recently had to toss an old desktop of mine. It was gradually getting slower and slower, and after shutting the desktop down for long periods of time, it would choke up upon startup. Sometimes it'd give a disk read error, sometimes say no OS was found, etc. Restarting it about 5-15 times would eventually boot properly. Weird. I also noticed that startup programs were going missing, Dropbox was reindexing my entire folder, and Backblaze was backing up less than the number of files that it should. This lead me to believe it was probably a hard drive issue. I began to wonder why I'd have hard drive issues, and came to closure when I assumed it was because of recent power surges and outages. I'm sure that does a number on the drive. I bought a new desktop recently. It's not a beast or anything, but it's enough for what I do. It's an eMachines (I know, I know) Ultra-Slim (http://www.amazon.com/eMachines-Ultra-Slim-ER1401-57-Desktop-PC/dp/B00475OG9U). This is ideal for me because it's small and portable. It comes with an AC adapter and battery, like a laptop. Just to be safe, I bought an uninterruptable power supply on top of that. It's basically protected completely from any outages that might scramble the drive. I set this up a few days ago and for the past few days I've been perfecting settings, downloading the usual applications, etc. Two days ago, I noticed Dropbox was reindexing my entire Dropbox folder. I installed both Dropbox and Backblaze on this system, but it is very much more lightweight than the other. Only about 15 third-party applications installed. I thought that maybe Dropbox and Backblaze were stressing my system, so I turned off Backblaze. Still, Dropbox runs and comes across this infinite reindex issue. I noticed that upon a reboot recently, two applications did not start on startup either. Also, much like my old desktop, every 3rd or 4th reboot, I'll be forced into a chkdsk. This makes me incredibly nervous. What could possibly be going wrong with my old, years-old desktop that is immediately causing the same issues to my new one? I've considered all of the basics. I'm in a very air conditioned room. I take run routine virus scans. I'd like to think I take care of my systems very well. What is this issue that is haunting me? There's always the possibility that this new desktop has a junk hard drive, but it just seems way too coincidental.

  Read the article

• Samba doesnt require password on xbmc but does on ubuntu

  - by Chris

  I have samba setup on a fedora 13 machine, and I use it to share with my xbmc client in the family room. When I set this up there no password or anything was required I merely entered in paths such as: smb://<host>/<share> and all worked. Now on my ubuntu 10.04 machine when I try to access the same hosts, for example through smbmount though I receive an error. smbmount //media/Music ~/Music/ # media is in my /etc/hosts and resolves to # correct IP address for the machine I receive error: operation not permitted after pressing enter when it prompts for password. Here is my entry from /etc/samba/smb.conf: [global] workgroup = WORKGROUP server string = Samba Server Version %v # log files split per-machine: log file = /var/log/samba/log.%m # maximum size of 50KB per log file, then rotate: max log size = 50 security = user passdb backend = tdbsam ; security = domain ; passdb backend = tdbsam ; realm = MY_REALM ; password server = <NT-Server-Name> ; security = user ; passdb backend = tdbsam ; domain master = yes ; domain logons = yes ; logon script = %m.bat ; logon script = %u.bat ; logon path = \\%L\Profiles\%u ; logon path = ; add user script = /usr/sbin/useradd "%u" -n -g users ; add group script = /usr/sbin/groupadd "%g" ; add machine script = /usr/sbin/useradd -n -c "Workstation (%u)" -M -d /nohome -s /bin/false "%u" ; delete user script = /usr/sbin/userdel "%u" ; delete user from group script = /usr/sbin/userdel "%u" "%g" ; delete group script = /usr/sbin/groupdel "%g" ; local master = no ; os level = 33 ; preferred master = yes ; wins support = yes ; wins server = w.x.y.z ; wins proxy = yes ; dns proxy = yes load printers = yes cups options = raw ; printcap name = /etc/printcap # obtain a list of printers automatically on UNIX System V systems: ; printcap name = lpstat ; printing = cups ; map archive = no ; map hidden = no ; map read only = no ; map system = no ; store dos attributes = yes #============================ Share Definitions ============================== [homes] comment = Home Directories browseable = no writable = yes ; valid users = %S ; valid users = MYDOMAIN\%S # Un-comment the following and create the netlogon directory for Domain Logons: ; [netlogon] ; comment = Network Logon Service ; path = /var/lib/samba/netlogon ; guest ok = yes ; writable = no ; share modes = no # Un-comment the following to provide a specific roving profile share. # The default is to use the user's home directory: ; [Profiles] ; path = /var/lib/samba/profiles ; browseable = no ; guest ok = yes # A publicly accessible directory that is read only, except for users in the # "staff" group (which have write permissions): ; [public] ; comment = Public Stuff ; path = /home/samba ; public = yes ; writable = yes ; printable = no ; write list = +staff [tv] comment = TV path = /media/Isos/tv public = yes writable = yes printable = no write list = +media [music] comment = Music path = /media/Storage/music/ public = yes writable = yes printable = no write list = +media [pictures] comment = Pictures path = /media/Storage/pictures public = yes writable = yes printable = no write list = +media

  Read the article

• Windows Media Player won't launch on Vista - how to repair or reinstall it?

  - by rpm1200

  My friend asked me to look at her Acer Aspire laptop with Vista Home Premium as it is no longer playing DVDs. I found that Windows Media Player would not launch. I found this thread, which contained a number of suggestions, none of which solved the problem. Here is what I tried: Tried running WMP via desktop shortcut, QuickLaunch bar or going to Program Files\Windows Media Player\wmplayer.exe. In all cases, wmplayer would launch then terminate immediately (verified through the Processes tab in Task Manager). Tried running wmplayer.exe as Administrator. The UAC dialog would come up, I'd approve, then wmplayer would launch and terminate immediately. Uninstalled all non-Microsoft media programs except RealPlayer, iTunes, QuickTime, Acer Arcade (the laptop owner uses all those apps). Tried running Program Files\Windows Media Player\setup_wm.exe as Administrator, it launched but said that a newer version of WMP was already installed. Deleted the "Windows Media" folder located under %userprofile%\appdata\local\Microsoft then tried starting WMP - wmplayer would launch and terminate immediately. Register wmp.dll by typing "regsvr32 wmp.dll" in an Administrator cmd window then tried starting WMP - wmplayer would launch and terminate immediately. Run "SFC /SCANFILE" in an Administrator cmd window - get an error message that it found invalid system files and could not fix them, so look at the log file cbs.log. The log file shows that there are broken files associated with Windows Sidebar (which the user does not use) but none relating to WMP. Log off to safe mode and run "SFC /SCANFILE" in an Administrator cmd window again - same results. Try to download and install XP WMP - the microsoft.com site recognizes the OS as Genuine and allows the download, but when I launch the installer it says the system is not Genuine. Clicking the link directs me back to IE where I can authenticate the system as Genuine. The installer still fails to recognize the system as Genuine. It is a Genuine Vista installation. Try to run this update (KB931621). The installer said it did not apply to the system. Set Windows Media Player as default in Program Access and Defaults. Same results. Tried running "for %a in (%systemroot%\system32\wm*.dll) do regsvr32 /s %a" in an Administrator cmd window - same results. Went to this Knowledge Base article (947541) and ran the Microsoft Fix It. The Fix It ran successfully, but WMP would still launch and terminate immediately. Multiple reboots in the process of doing all of these steps. After all this, looked in the Application and Security logs. No events pertaining to WMP were logged. The computer was preinstalled with Vista Home Premium and I have the Acer backup DVDs which will reimage the drive. I do not have Vista install DVDs. Reimaging the system is not an option. I'd also rather not restore the system to an earlier point unless it's absolutely necessary. What else can I do to repair or reinstall WMP?

  Read the article

• Set up lnux box for hosting a-z [apache mysql php ssl]

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP: To upgrade PHP to the latest version, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! cd /tmp #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm #rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm #rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. [will list all packages available in the IUS repo] rpm -qa | grep php [will list installed packages needed to be removed. the installed packages need to be removed before you can install the IUS packages otherwise there will be conflicts] #yum shell >remove php-gd php-cli php-odbc php-mbstring php-pdo php php-xml php-common php-ldap php-mysql php-imap Setting up Remove Process >install php53 php53-mcrypt php53-mysql php53-cli php53-common php53-ldap php53-imap php53-devel >transaction solve >transaction run Leaving Shell #php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) This process removes the old version of PHP and installs the latest. To upgrade mysql: Pretty much the same process as above with PHP #/etc/init.d/mysqld stop [OK] rpm -qa | grep mysql [installed mysql packages] #yum shell >remove mysql mysql-server Setting up Remove Process >install mysql51 mysql51-server mysql51-devel >transaction solve >transaction run Leaving Shell #service mysqld start [OK] #mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure Virtualhosts for SSL, setting up a CA, setting up SFTP with openSSH, or anything else would be appreciated.

  Read the article

• Installing XP through USB-flash disc

  - by Crazy Buddy

  I don't know whether this could be asked here... So, Pardon me for this. Probably, this is based on My laptop and a contradiction to this question asked already here... I tried to format my "government-provided" laptop (No CD-drive). I thought those IT guys are proving that they're too smart..! I have the Windows XP CD right now. I didn't like to stick with some home-made OS from our Government. So, I used another laptop to format the govt. thing and tried to install XP (As I didn't have enough bills to invest on Windows 7 or 8). Case 1: First, I allowed WinSetupFromUSB 1.0 beta 8 to deal with the flash disk. I wondered for the first time that XP text-screen appeared. Using the first part, I formatted my laptop. It started to copy files, entered into the next part, and completed the installation. I started my PC for the first time. XP splash screen appeared. Suddenly, a blue screen flashed and disappeared (I can't even read what it says). Rebooted and arrived at the screen, "Start Windows Normally". It happens and happens still - like an infinite loop :-) Case 2: Next, I used Rufus 1.2.0 to transfer files to my Flash and it screwed everything out. Even if I used Flash to boot, it arrives to the same screen "Start Windows normally". It doesn't show any response of Flash being inserted. Then I recognized that, It's simply copies everything to the flash disk. Case 3: Then, I started with Novicorp WinToFlash (giving utmost priority to this site). I booted with the disk. I entered into the first part - "Text mode". Some lines started running like that "Press F6 if you..." like that. The last thing I saw was, "Setup is starting Windows..." Suddenly a blue screen appeared like this captured one. I've a suspicion that the same screen appears again & again in first case. Man, I'm dead. Case 4: For the sake of my last hope, I used WinSetupFromUSB 0.1.1. I was shocked on arriving at a screen which says something "GRUB4DOS" like that and some commands like {command line, reboot, halt, \find menu.lst} and when I go inside those "find" options, I see "Error:15 - File not found". Googling provided some commands to mount SETUPLDR.BIN file in the "grub" thing which also proved unsuccessful... Some sites say that Factory reset uses only some function keys. A guy said that it's F11 for lenovo. Screw him. It's all a waste-of-time. But, I think SE would help me out. Is our government IT guys doin' this to me? Are they Soooo smart to spark some blue screen in front of me to freak me out? Any suggestions or new (useful) USB transferring things would be appreciated. It's very urgent. So, It'd be better if you guys pay some attention in debugging and help me out..? Thanks for your time guys :-)

  Read the article

• Trying to prevent Windows from hibernating/sleeping automatically

  - by user328821

  My Dell XPS 8700 (Win 7) suddenly began putting itself to sleep at 6pm daily, even if I'm typing. I don't know what caused this to occur, except possibly a windows update that took place in the middle of the night. I initially went into settings for power and saw 2 plans set up, one from Dell and the other window's Power saver plan. I set both to never for sleep and hibernate yet it still occurred. I have current drivers and a fairly new UPS that has software to set to shutdown only after power loss. Dell is of little help, can anyone point me in the right direction? I did do the powerdfg -energy program and came up with this: Power Efficiency Diagnostics Report Scan Time 2014-05-08T19:21:48Z Scan Duration 60 seconds System Manufacturer Dell Inc. System Product Name XPS 8700 BIOS Date 08/23/2013 BIOS Version A04 OS Build 7601 Platform Role PlatformRoleDesktop Plugged In true Process Count 115 Thread Count 1631 Report GUID {097caf99-039b-44c3-b154-d797bfbfdfcc} Analysis Results Errors Power Policy:Sleep timeout is disabled (Plugged In) The computer is not configured to automatically sleep after a period of inactivity. System Availability Requests:System Required Request The device or driver has made a request to prevent the system from automatically entering sleep. Requesting Driver Instance HDAUDIO\FUNC_01&VEN_10EC&DEV_0899&SUBSYS_102805B7&REV_1000\4&220b1bbc&0&0001 Requesting Driver Device Realtek High Definition Audio CPU Utilization:Processor utilization is high The average processor utilization during the trace was high. The system will consume less power when the average processor utilization is very low. Review processor utilization for individual processes to determine which applications and services contribute the most to total processor utilization. Average Utilization (%) 9.48 Warnings Platform Timer Resolution:Platform Timer Resolution The default platform timer resolution is 15.6ms (15625000ns) and should be used whenever the system is idle. If the timer resolution is increased, processor power management technologies may not be effective. The timer resolution may be increased due to multimedia playback or graphical animations. Current Timer Resolution (100ns units) 10000 Maximum Timer Period (100ns units) 156001 Platform Timer Resolution:Outstanding Kernel Timer Request A kernel component or device driver has requested a timer resolution smaller than the platform maximum timer resolution. Requested Period 10000 Request Count 2 Platform Timer Resolution:Outstanding Timer Request A program or service has requested a timer resolution smaller than the platform maximum timer resolution. Requested Period 10000 Requesting Process ID 8672 Requesting Process Path \Device\HarddiskVolume3\Program Files (x86)\Mozilla Firefox\firefox.exe Platform Timer Resolution:Outstanding Timer Request A program or service has requested a timer resolution smaller than the platform maximum timer resolution. Requested Period 100000 Requesting Process ID 1212 Requesting Process Path \Device\HarddiskVolume3\Windows\System32\svchost.exe Power Policy:802.11 Radio Power Policy is Maximum Performance (Plugged In) The current power policy for 802.11-compatible wireless network adapters is not configured to use low-power modes. CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace. Process Name audiodg.exe PID 1304 Average Utilization (%) 4.73 Module Average Module Utilization (%) \Device\HarddiskVolume3\Windows\System32\msvcrt.dll 1.88 \Device\HarddiskVolume3\Windows\System32\MaxxAudioAPO5064.dll 1.77 \Device\HarddiskVolume3\Windows\System32\AudioEng.dll 0.80 CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace. Process Name thunderbird.exe PID 6036 Average Utilization (%) 0.35 Module Average Module Utilization (%) \Device\HarddiskVolume3\Program Files (x86)\Mozilla Thunderbird\xul.dll 0.16 \Device\HarddiskVolume3\Program Files (x86)\Mozilla Thunderbird\mozjs.dll 0.05 \SystemRoot\System32\win32k.sys 0.03 CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace. Process Name dwm.exe PID 1340 Average Utilization (%) 0.25 Module Average Module Utilization (%) \Device\HarddiskVolume3\Windows\System32\dwmcore.dll 0.08 \Device\HarddiskVolume3\Windows\System32\nvwgf2umx.dll 0.05 \SystemRoot\system32\ntoskrnl.exe 0.03 CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace.

  Read the article

< Previous Page | 576 577 578 579 580 581 582 583 584 585 586 587  | Next Page >