Search Results

Search found 46075 results on 1843 pages for 'system cats lol'.

Page 584/1843 | < Previous Page | 580 581 582 583 584 585 586 587 588 589 590 591  | Next Page >

• Software Raid 10 corrupted superblock after dual disk failure, how do I recover it?

  - by Shoshomiga

  I have a software raid 10 with 6 x 2tb hard drives (raid 1 for /boot), ubuntu 10.04 is the os. I had a raid controller failure that put 2 drives out of sync, crashed the system and initially the os didnt boot up and went into initramfs instead, saying that drives were busy but I eventually managed to bring the raid up by stopping and assembling the drives. The os booted up and said that there were filesystem errors, I chose to ignore because it would remount the fs in read-only mode if there was a problem. Everything seemed to be working fine and the 2 drives started to rebuild, I was sure that it was a sata controller failure because I had dma errors in my log files. The os crashed soon after that with ext errors. Now its not bringing up the raid, it says that there is no superblock on /dev/sda2, even if I assemble manually with all the device names. I also did a memtest and changed the motherboard in addition to everything else. EDIT: This is my partition layout Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0009c34a Device Boot Start End Blocks Id System /dev/sdb1 * 2048 511999 254976 83 Linux /dev/sdb2 512000 3904980991 1952234496 83 Linux /dev/sdb3 3904980992 3907028991 1024000 82 Linux swap / Solaris All 6 disks have the same layout, partition #1 is for raid 1 /boot, partition #2 is for raid 10 far plan, partition #3 is swap, but sda did not have swap enabled EDIT2: This is the output of mdadm --detail /dev/md1 Layout : near=1, far=2 Chunk Size : 64k UUID : a0feff55:2018f8ff:e368bf24:bd0fce41 Events : 0.3112126 Number Major Minor RaidDevice State 0 8 34 0 spare rebuilding /dev/sdc2 1 0 0 1 removed 2 8 18 2 active sync /dev/sdb2 3 8 50 3 active sync /dev/sdd2 4 0 0 4 removed 5 8 82 5 active sync /dev/sdf2 6 8 66 - spare /dev/sde2 EDIT3: I ran ddrescue and it has copied everything from sda except a single 4096 byte sector that I suspect is the raid superblock EDIT4: Here is some more info too long to fit here lshw: http://pastebin.com/2eKrh7nF mdadm --detail /dev/sd[abcdef]1 (raid1): http://pastebin.com/cgMQWerS mdadm --detail /dev/sd[abcdef]2 (raid10): http://pastebin.com/V5dtcGPF dumpe2fs of /dev/sda2 (from the ddrescue cloned drive): http://pastebin.com/sp0GYcJG I tried to recreate md1 based on this info with the command mdadm --create /dev/md1 -v --assume-clean --level=10 --raid-devices=6 --chunk=64K --layout=f2 /dev/sda2 missing /dev/sdc2 /dev/sdd2 missing /dev/sdf2 But I can't mount it, I also tried to recreate it based on my initial mdadm --detail /dev/md1 but it still doesn't mount It also warns me that /dev/sda2 is an ext2fs file system but I guess its because of ddrescue

  Read the article

• How to copy password from Mono-executed KeePass2 to xterm on Linux?

  - by Steve Emmerson

  I use KeePass2 to access username/password information in a Dropbox file. This allows convenient access from multiple devices. I can't seem to copy a password to the clipboard on my Linux 2.6.27.41-170.2.117.fc10.x86_64 system, however, in order to supply the password to a prompt in an xterm(1). I've tried both Ctrl+C/Ctrl+V and highlighting and mouse button 2 clicking. The KeePass2 program on the Linux system is executed by Mono. How can I copy the password to the xterm(1)? [Aside: I think we need a "KeePass" tag.] ADDENDUM: My mouse buttons were misconfigured: button 2 wasn't set to "copy". Sorry for the false alarm.

  Read the article

• How do I lower idle cpu usage in ubuntu linux? Gnome or KDE Variants

  - by Jasen

  My question comes from a kde desktop currently, but it also happens with the gnome instance. When just sitting there, with only the cpu monitor widget running. no open windows, no background processes other than the desktop, my cpu is at ~20%. I wanna know how to fix this, and possibly get better performance out of it. When running my windows side, the cpu will sit at zero, and i generally load new programs about 400ms faster. With windows 7 being as slow as it is, this is not acceptable. and the widget is only set to check every 500ms, so im almost completely sure its not the widget. My system is a Gateway nv 53 amd 2.0 ghz turion with 4 gb of installed ram, and 500 gb hd. both linux and windows are 64 bit. average ram use on either system is about 1.4 gb for just the os

  Read the article

• Ubuntu Volume overriding settings set in Alsamixer

  - by Hayek

  Problem: How do I "lock in" the volume I set through alsamixer? I'm running Ubuntu 9.10. I adjusted the bass/treble columns in alsamixer but changing the system volume resets them all back to 100% I did save the settings by running alsactl store but everything is reset once I touch Ubuntu's volume icon in the top menu bar. This is rather painful because the computer is hooked up to a 650watt system with a massive subwoofer. As much as I enjoy my music, there's no need to have the walls vibrate :) What can I do to prevent Ubuntu from overriding the settings?

  Read the article

• Preventing logrotate's dateext from overwriting files

  - by Thirler

  I'm working with a system where I would like to use the dateext function of logrotate (or some other way) to add the date to a logfile when it is rotated. However in this system it is important that no logging is missing and dateext will overwrite any existing files (which will happen if logrotate is called twice on a day). Is there a reliable way to prevent dateext to overwrite existing files, but instead make another file?. It is acceptable that either no rotate happens or a file is created with a less predictable name (date with an extra number, or the time or something).

  Read the article

• Domain controller failed to restore using windows backup tools

  - by Peilin

  Domain controller failed to restore using windows backup tools One Issue: One 08 R2 domain controller with fully daily backup(only one controller in this company) is out of services due to hardware issue. The below two methods i tried to recover to the new purchasing server,but it is fail. 1)First Method: Using the windows 2008 R2 CD to boot and carry out recover from backup. Everything is OK, but after reboot it will come out blue screen and restart again. 2)Second Method: a)Install the OS in this new server b) Reboot the server to DSRM. c)Using the Windows Backup Tools to restore the system states only After reboot, it will come out the blue screen error and restart again. I know this is may be the different hardware issue, but how to resolve? Or can we only restore the AD services not whole system status? Any suggestion?

  Read the article

• How to determine the source for wakeup in hibernate

  - by Erik

  I have a big problem with my home theater PC that runs Windows 7 64Bit. Normally, I send that PC to hibernate every evening, but from time to time, it keeps waking up for no obvious reason, and stays on until I realize, which is sometimes half a day later :( I have already checked for Windows update, which is not set to automatical, since I prefer installing updates manually. When I look in the system event log, there is an entry called "Power Troubleshooter" which tells me that my system was reactivated at a specific time, but it also says: Source = Unknown, which is the most annoying part. So how can I actually figure out, which process reactivates the PC? Is it possible to set a group policy which forbidds applications or services from scheduling tasks that allow waking up from hibernate at all?

  Read the article

• water cooler fan in my computer room............

  - by metal gear solid

  Is using water cooler fan in my computer room HARMFUL for the internal parts of the computer system?

  Read the article

• Windows 8 to 8.1 Pro Upgrade SecureBoot Error

  - by Alexandru

  I upgraded from Windows 8 to Windows 8.1. I have an Alienware Aurora R4 with the latest BIOS firmware version, A09. Ever since I did the upgrade, I get a watermark on my desktop saying, "SecureBoot isn't configured correctly"...I would like to get rid of this watermark the correct way (not by hacking system DLLs). My BIOS shows me booting in UEFI mode, and I see that SecureBoot is actually disabled from there. I cannot enable SecureBoot, in either UEFI mode or Legacy Boot mode. Note, I can't even get Legacy Boot mode working without re-formatting my system which I really don't plan on doing, so my question is this...what has changed in the way Windows handles SecureBoot? As far as I can tell, I do not have SecureBoot enabled, and it is trying to tell me that it isn't configured correctly. Why does it even care to check if my BIOS doesn't have it on anyways?! Its so frustrating!

  Read the article

• Schedled Tasks and Environment Variables

  - by Andrew J. Brehm

  I have a scheduled task, a batch file, that uses an environment variables which is set system-wide. On server 1, the scheduled task runs under a domain account and the environment variable works. The environment variable also exists in my session and when I runas as the service account. On server 2, the scheduled task runs under a different domain account and the environment variable DOES NOT work. However, the environment variable does exist in my session and when I runas as the service account. On both servers the environment variable has been set system-wide by the same script originally. The script runs again every now and then and as far as I can see noone has tempered with the environment variable. The scheduled tasks are set up identically on the two servers (using the same XML file) and the two service accounts are identically configured (as far as I know). What am I doing wrong?

  Read the article

• Linux: Automatically switch to external monitor (VGA)

  - by peoro

  I've got an eeePC with a really tiny monitor, so whenever I go (home, faculty, parent's home, friend's home, ...) I attach it to any external monitor I can find. If it matters my system is like this: Archlinux Linux 2.6.36 Xorg 7.6 X server 1.9.2 Intel Corporation Mobile 945GME Express Integrated Graphics Controller (fully accelerated by intel modules) When I boot up the system, it uses the integrated monitor (LVDS1) only, and I have to manually manually switch to the external monitor (VGA1) using xrandr. Is it possible to configure my Xorg (or whatever) so that it uses the VGA1 output if present?

  Read the article

• Will my RAID0 stay intact when I move it to a new computer?

  - by Jeremy H

  My primary drive is a 250GB WD SATA drive. So, I added 2x 500GB 7,200 RPM WD SATA drives into my Windows Vista box and created a 1TB RAID0. I then formatted the the primary drive and installed Windows 7. To my pleasant surprise when I booted into Windows 7 my RAID0 was still intact and I kept trotting along the same as I did before. Now I am replacing my motherboard, processor, and RAM and plan on formatting the primary 250GB drive again and using it to boot for a new clean install of Windows 7. My question is: if I move these two SATA drives which are setup for RAID0 into the new system, install Windows 7 again, will the RAID0 remain? Edit: Software RAID. I created it within Windows. The RAID0 does NOT contain the system boot partition.

  Read the article

• How to resize an encrypted LVM in RAID 1 in Linux?

  - by user28712

  Hi, I am running 3 partitions in RAID 1. Partition : Mountpoint : Filesystem : Encrypted : LVM ------------------------------------------------------ 1 : /boot : ext2 : No : No 2 : / : ext3 : Yes : No 3 : /home : xfs : Yes : Yes It now happens that I have given the root of the system too few gigs; i would like to shrink the LVM (3) and give the root(2) more space. How can I do this safely without messing up the system? In what order do I have to resize the raid partitions, encryption, lvm, file systems? Any help would be greatly appreciated. Adriaan

  Read the article

• How can I get a list of default documents in IIS using PowerShell?

  - by SGarratt

  I'm managing a Server Core machine and trying to do everything in PowerShell, which is fun. I need a list of the default documents. From other websites, I've found out how to set and remove them, using both xxx-WebConfiguration and xxx-WebConfigurationProperty. I've tried: Get-WebConfigurationProperty -Filter /system.webServer/defaultDocument -PSPath "IIS:\sites\Default Web Site" -Name files but it gives: Collection : {Microsoft.IIs.PowerShell.Framework.ConfigurationElement, Microsoft.IIs.PowerShell.Framework.Configuration Element, Microsoft.IIs.PowerShell.Framework.ConfigurationElement, Microsoft.IIs.PowerShell.Framework.Confi gurationElement...} ItemXPath : /system.webServer/defaultDocument Attributes : {} ChildElements : {} ElementTagName : files Methods : Schema : Microsoft.IIs.PowerShell.Framework.ConfigurationElementSchema which doesn't really help.

  Read the article

• Time randomly changing itself, internet randomly dying

  - by Vee

  Operating System MS Windows 8 Enterprise 64-bit CPU Intel Core i7 2700K @ 3.50GHz 45 °C Sandy Bridge 32nm Technology RAM 8,00 GB Dual-Channel DDR3 @ 800MHz (8-8-8-24) Motherboard ASRock Z77 Extreme4-M (CPUSocket) 40 °C Graphics SMXL2270HD (1920x1080@60Hz) M2094D-PZ (1680x1050@60Hz) 896MB GeForce GTX 275 (CardExpert Technology) 57 °C Hard Drives 466GB FUJITSU MAXTOR STM3500320AS (SATA) 39 °C Optical Drives ASUS DRW-2014L1T Audio High Definition Audio Device Hello everyone, I installed Windows 8 RTM a few weeks ago. It's not my first time installing it, but it's the first time having two annoying problems: 1) Randomly, the system clock changes time all by itself - to fix it I have to open the time window and sync it with the internet. 2) Randomly, internet connection stops working - to fix I have to run troubleshooting. Windows will find a problem with IP on the "Ethernet" connection and fix it. 3) In rare occasions, my PC freezes and I need to restart it (a BSOD once happened, but after that only freezes) How can I permanently solve these problems? This is what I've already tried: Reset Virus scan Stop/reset the Windows Time service Disable/re-enable Windows Time automatic internet sync Change time from BIOS Change motherboard battery

  Read the article

• How To Cancel Pending Windows 7 Updates

  - by Itai

  How To Cancel Pending Windows 7 Updates? The key is pending. The shutdown button has the windows update symbol meaning that there are updates that were selected to be installed which were download and will be installed upon shutdown. The only thing is that my machine will no longer boot if I let it install those updates! They are incompatible with a driver needed in the system and I did not found out until too late. The system admin used a recovery disk to get back to the previous restore point, only the updates are now pending, so I need to cancel those before the machine shutdowns next.

  Read the article

• wifi connection turns off oll the time

  - by er-v

  Hello! I realy need help with one strange problem. I have a wifi network in my appartment with wireless N home router Trendnet tew-652BRP. Everething work fine for three of my laptops, but I have one PC with D-Link DWA-140 adapter. It looses connection 2-3 times in 5 minutes. There is following messages in my system log when it does so: The browser has forced an election on network \Device\NetBT_Tcpip_{9537A5C1-3B43-4C56-B94C-CE69A257C3AD} because a master browser was stopped. The TCP/IP NetBIOS Helper service was successfully sent a stop control. The reason specified was: 0x40030011 [Operating System: Network Connectivity (Planned)] Comment: None The TCP/IP NetBIOS Helper service entered the stopped state. in order of appearence. How can I stop it? I have the latest driver installed.

  Read the article

• Corrupt Vista Account - With a twist

  - by oldSkool-Soldier

  I have a Windows Vista system whose profile seems to have been corrupted. Many solutions seem to indicate that you create another admin account, log in as that account, and delete the offending profile information for the account that is corrupted. Here's the twist: There are two accounts on this System - 1. Administrator Account 2. Standard Account. It's the Administrator Account which has become corrupted. If you attempted to do any user managment / attempt to create a new account under the 'Standard Account', UAC prompts for a user/pass. It has the admin account come up by default, and asking for a password (of which, there is none). When you click 'OK' - nothing happens (no doubt due to the fact that the account is corrupted, so it can't verify who or what is trying to allow the administrative privilage). Can anyone think of a way of fixing this account, or creating another administrator account to resolve this issue? Many thanks in advance.

  Read the article

• SSH Connection Refused - Debug using Recovery Console

  - by olrehm

  Hey everyone, I have found a ton of questions answered about debugging why one cannot connect via SSH, but they all seem to require that you can still access the system - or say that without that nothing can be done. In my case, I cannot access the system directly, but I do have access to the filesystem using a recovery console. So this is the situation: My provider made some kernel update today and in the process also rebooted my server. For some reason, I cannot connect via SSH anymore, but instead get a ssh: connect to host mydomain.de port 22: Connection refused I do not know whether sshd is just not running, or whether something (e.g. iptables) blocks my ssh connection attempts. I looked at the logfiles, none of the files in /var/log contain any mentioning on ssh, and /var/log/auth.log is empty. Before the kernel update, I could log in just fine and used certificates so that I would not need a password everytime I connect from my local machine. What I tried so far: I looked in /etc/rc*.d/ for a link to the /etc/init.d/ssh script and found none. So I am expecting that sshd is not started properly on boot. Since I cannot run any programs in my system, I cannot use update-rc to change this. I tried to make a link manually using ln -s /etc/init.d/ssh /etc/rc6.d/K09sshd and restarted the server - this did not fix the problem. I do not know wether it is at all possible to do it like this and whether it is correct to create it in rc6.d and whether the K09 is correct. I just copied that from apache. I also tried to change my /etc/iptables.rules file to allow everything: # Generated by iptables-save v1.4.0 on Thu Dec 10 18:05:32 2009 *mangle :PREROUTING ACCEPT [7468813:1758703692] :INPUT ACCEPT [7468810:1758703548] :FORWARD ACCEPT [3:144] :OUTPUT ACCEPT [7935930:3682829426] :POSTROUTING ACCEPT [7935933:3682829570] COMMIT # Completed on Thu Dec 10 18:05:32 2009 # Generated by iptables-save v1.4.0 on Thu Dec 10 18:05:32 2009 *filter :INPUT ACCEPT [7339662:1665166559] :FORWARD ACCEPT [3:144] :OUTPUT ACCEPT [7935930:3682829426] -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp --dport 25 -j ACCEPT -A INPUT -p tcp -m tcp --dport 993 -j ACCEPT -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -p tcp -m tcp --dport 143 -j ACCEPT -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 8080 -s localhost -j ACCEPT -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 -A INPUT -j ACCEPT -A FORWARD -j ACCEPT -A OUTPUT -j ACCEPT COMMIT # Completed on Thu Dec 10 18:05:32 2009 # Generated by iptables-save v1.4.0 on Thu Dec 10 18:05:32 2009 *nat :PREROUTING ACCEPT [101662:5379853] :POSTROUTING ACCEPT [393275:25394346] :OUTPUT ACCEPT [393273:25394250] COMMIT # Completed on Thu Dec 10 18:05:32 2009 I am not sure this is done correctly or has any effect at all. I also did not find any mentioning of iptables in any file in /var/log. So what else can I do? Thank you for your help.

  Read the article

• Why does my CPU Usage reach 100% too often?

  - by deathlock

  I'm using a dual-core processor and often see my CPU usage reaches 100%. I realize this may happen if I'm running too much applications, so when I know the computer starts to run slowly, I start to close my applications. I usually run 4-5 applications simultaneously. Usually those are: web browser (Google Chrome), Adobe Photoshop, Notepad++, XAMPP, and Windows Task Manager. Usually I close tabs in my Chrome first, because I often browse the net with about 20 tabs/4 windows open, so I presume that would take much memory (bad habit, I know). But even after closing Chrome's tabs or closing other applications, my CPU Usage often stays at high percentage - 72% at best, 100% at worst. I check the Processes tab on Windows Task Manager and usually found the System, System Idle Process, or services.exe taking the highest CPU process (could reach 60). Why is this happening? And is there any solution? EDIT I have T2250 @ 1,73 Ghz and 2.5 GB RAM

  Read the article

• How to disable color dithering for low-bit-depth screen settings?

  - by gogowitsch

  I am using Terminal Services and TeamViewer a lot to access other computers, partly over slow networks. The problem described below is not affected by which of the two remote access services I am using. When accessing Windows 7 Professional machines, a great deal of text is hard to read as the background is dithered. Even for exactly the same colors, Windows 2003 does not seem to dither at all, but to choose the closest available color. I strongly prefer the latter, as I don't care for the exact colors, I just want to be able to read easily. I am not sure whether this is operating system-related. The programs on the remote systems do not allow me to change the color choices for the various backgrounds to anything sane. Is there a way to disable this color dithering using some target operating system setting that will do the trick for both Terminal Services and TeamViewer?

  Read the article

• Can a working Tomcat 6 webapp be turned into a usable .war file?

  - by Bill Cole

  Problem: I have a working webapp on a FreeBSD 8.1 Tomcat 6 test server that I need to move to a production system. The developer who last touched it (and had root on that server) has moved on and isn't helpful. The running app seems to have been deployed from a CVS server that is now unavailable. My thinking is that I would like to find a way to wrap the working webapp into a proper .war so that I can deploy it on a pristine host and (after testing) send the existing system to a very deep bitbucket. But I'm not having luck finding a way to do that. I'm a sysadmin not a developer and don't work much with Tomcat systems so I may be (likely am) overlooking something blindingly simple. I gather that I may be able to just tar up the deployed directory and untar it on the new machine, but I have a nagging feeling that there are pitfalls in that.

  Read the article

• MS DPM 2007: Testing the Recovery for a Production Domain

  - by NewToDPM

  Hi everybody! MS DPM 2007 is a new technology in my company, and so am I to the product. We have a classic Microsoft domain with two DCs, Exchange 2007 and a couple Web/MS SQL servers. I have deployed DPM one month ago on the domain, and after fixing the various issues I got with the replicas inconsistence and adapting the schedule and retention range to the server storage pool size, I can say the backup system is working correctly (no errors) as of today. However, there is one problem: we did not attempt to restore from the backups yet, which is a big no-no of course. I'm not sure about the way I should handle this, my main concern being Exchange and the System State of the DCs. From my understanding, DPM can only protect AND restore data on a server which is part of the same domain as the backup server. If I restore the System State (containing Active Directory) and the Exchange Storage Groups on a testing server, I am afraid it would completely disturb the domain functioning (for example, having two primary DCs on the domain). I am thinking about building a second DPM server on a testing separate domain which would mirror the replicas and then restore it on testing servers from this new domain. Is it the right way to handle the data recovery testing? How did you do on your domain when you first deployed DPM? I'd be grateful for any link/documentation or advice. Thank you in advance for your help! EDIT: Two options seem possible so far: i. Create another DC/Exchange server in the alternate location; ii. Create a separate domain in the alternate location and setup a trust between this domain and the production one. The option i is certainly the best but implies setting up a secondary Exchange server, with a dedicated public IP address so that if Exchange #1 dies, we can still send emails with Exchange #2. I don't know how complex this can be and would need to discuss it with my colleagues. The option ii would only fit the testing purposes. My only question regarding this is: if my production and DPM servers are part of domain A, and there is a trust between domains A and B, can I restore a domain A content to any domain B server?

  Read the article

• What does the the reconstruction process of mdadm do exactly on raid10

  - by Azrael

  I've got a system with 4 disks set up as raid10. All disks are usable, and mdadm all states them with UUUU. Due to a recent system crash, the raid is currently reconstruction the raid as it was marked as "not clean," and a reconstruction process was started. On a closer look smartctl shows problems on one disk: sd 0:0:0:0: [sda] Unhandled sense code sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE sd 0:0:0:0: [sda] Sense Key : Medium Error [current] [descriptor] Descriptor sense data with sense descriptors (in hex): 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00 24 cd 78 d4 sd 0:0:0:0: [sda] Add. Sense: Unrecovered read error - auto reallocate failed sd 0:0:0:0: [sda] CDB: Read(10): 28 00 24 cd 75 1e 00 04 00 00 With a research about the reconstruction process, I only found information concerning raid5 but nothing for raid10. Can I replace this problematic disk during the reconstruction process, or will I kill the raid with this?

  Read the article

• DPM - Monitoring is green, Protection has error and Latest rec point is old. How do I interpret that?

  - by LosManos

  How do I read the DPM info in this case? Monitoring says Failed but Protection shows Ok while having a Latest recovery point from last year. Under Monitoring tab I have Failed for Source | Computer | Protection group | Start time Computer\System Protection | MyServerName | Recovery point | 2014-06-09 19:00:00 which shows me that something happened last night. But under Protection tab everything is green. Here I have Protection group member | | Protection status Protection group ..name.. Computer: MyServerName Computer\System protection Bare metal recovery OK ... Latest recovery point: 2013-12-12 06:32:54 My guess is that backup failed last night once, but succeeded later. It then found out that there hasn't been any change since sometime last year and leave it be and flags Ok.

  Read the article

< Previous Page | 580 581 582 583 584 585 586 587 588 589 590 591  | Next Page >