Search Results

Search found 12068 results on 483 pages for 'sv gets'.

Page 59/483 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

• QoS for Cisco Router to Prioritize Voice and Interactive Traffic

  - by TJ Huffington

  I have a Cisco 891W NATing Voice and Data to the internet over a 10mbit/2mbit connection. Voice traffic gets degraded when I upload large files. Pings time out as well. I tried to configure a QoS policy but it's basically not doing anything. Voice traffic still degrades when upload bandwidth gets saturated. Here is my current configruation: class-map match-any QoS-Transactional match protocol ssh match protocol xwindows class-map match-any QoS-Voice match protocol rtp audio class-map match-any QoS-Bulk match protocol secure-nntp match protocol smtp match protocol tftp match protocol ftp class-map match-any QoS-Management match protocol snmp match protocol dns match protocol secure-imap class-map match-any QoS-Inter-Video match protocol rtp video class-map match-any QoS-Voice-Control match access-group name Voice-Control policy-map QoS-Priority-Output class QoS-Voice priority percent 25 set dscp ef class QoS-Inter-Video bandwidth remaining percent 10 set dscp af41 class QoS-Transactional bandwidth remaining percent 25 random-detect dscp-based set dscp af21 class QoS-Bulk bandwidth remaining percent 5 random-detect dscp-based set dscp af11 class QoS-Management bandwidth remaining percent 1 set dscp cs2 class QoS-Voice-Control priority percent 5 set dscp ef class class-default fair-queue interface FastEthernet8 bandwidth 1024 bandwidth receive 20480 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto auto discovery qos crypto map mymap max-reserved-bandwidth 80 service-policy output QoS-Priority-Output crypto map mymap 10 ipsec-isakmp set peer 1.2.3.4 default set transform-set ESP-3DES-SHA match address 110 qos pre-classify ! fa8 is my connection to the internet. Voice traffic goes over a VPN ("mymap") to the SIP server. That's why I specified "qos pre-classify" which I believe is the way to classify traffic over the VPN. However even when I ping a public IP while saturating upload bandwidth, the latency is exceptionally high. Is this configuration correct? Are there any suggestions that might make this work for my setup? Thanks in advance.

  Read the article

• Remote Desktop Mobile mangles barcodes coming from scanner

  - by sfonck

  We have an application here using handhelds to scan barcodes. These handhelds are actually making a remote desktop session towards a server where the application runs. Works fine. Now we have bought some new Motorola MC55's running 'Windows Mobile 6.1 Classic', and when using the application over remote desktop: it mangles the characters of the barcodes.... I already tried following things: When scanning a barcode on the MC55 itself it is displayed correctly When scanning a barcode via the remote desktop into a notepad session it is incorrect. Played with all options of the 'Remote Desktop Mobile' - no result Disabled 'autocorrect' and 'suggest words when entering text' on the input settings - no result The strange things is: a barcode which consists of only numbers gets scanned correctly the mangled characters comes through in lower case For some codes \t is mangled in between (should normally be entered after the barcode) e.g.: 'PERIN4' becomes 'ERINp4' 'MGZB' becomes 'GZB m' 'BAK664' becomes 'AK664 b' 'MAGBFA01' becomes 'AGBFmA01' '5021879949500' gets scanned correctly Final solution: Suppllier of the handhelds said the handheld was sending the characters too fast over the remote desktop connection. They changed the handheld to wait for 50ms between sending each character, which produced correct results right now. Scanning a barcode became somewhat slower but it's almost not remarkable to endusers.

  Read the article

• HowTo import Certificate (pfx) with private key in WinXP

  - by Gunther

  Hello, I tried the whole day just to import a cetrificate in winXP, but I allways failed. I did following: Create the certificate with private key (no pasword): makecert -sr LocalMachine -ss My -pe -sky exchange -n "CN=TestCert" -a sha1 -sv TestCert.pvk TestCert.cer Then put certificate and private key together into pfx file: pvk2pfx.exe -pvk TestCert.pvk -spc TestCert.cer -pfx TestCert.pfx Import pfx file with commandline tool (German System): winhttpcertcfg.exe -i TestCert.pfx -a NT-AUTORITÄT\NETZWERKDIENST -c LOCAL_MACHINE\My Error: Unable to import contents of PFX file. Please make sure the filename and path, as well as the password, are correct. Hint: "NT-AUTORITÄT\NETZWERKDIENST" -- "NT-AUTHORITY\NETWORKSERVICE" Filename is ok, password was not set. Even if I set the password (e.g. "MyPassword") in Step 1 and type at the end of step 3: ... -p MyPassword I got the same error. Then I tried to import in the certificate console (mmc with certificate snap-in). There i got following error: "Der private Schlüssel, den Sie importieren, erfordert möglicherweise einen Dienstanbieter, der nicht installiert ist." -- "The imported private key may requires a service-supplier which is not installed". But the Microsoft Crypto-Service is up and running. What else can I do? On Windows Vista and Windows 7 I got this running without these problems. I need this Certificate to run a WCF Service. Thanks in advance for any hint. Regards, Gunther

  Read the article

• Two domains, two servers, one dynamic IP address

  - by giantman

  I have two domains hi.org and bye.net and one dynamic IP address and two servers. I want to attach one domain bye.net to server1 and hi.org to server2. I'm using Apache wamp 2.0i. I have two servers behind one router with a dynamic IP address #httpd.conf file additions <IfModule mod_proxy.c> ProxyRequests Off <Proxy *> Order deny,allow Allow from all </Proxy> </IfModule> #vhost file additions NameVirtualHost *:80 #default <VirtualHost *:80> DocumentRoot "c:/wamp/www/fallback" </VirtualHost> # Server 1 <VirtualHost *:80> DocumentRoot "c:/wamp/www" ServerName h**p://bye.net ServerAlias bye.net </VirtualHost> # Server 2 <VirtualHost *:80> ProxyPreserveHost On ProxyPass / h**p://192.168.1.119/ DocumentRoot "g:/wamp/www" ServerName h**p://hi.org ServerAlias hi.org </VirtualHost> After doing all this I fallback to server1 only I don't get the page hi.org I only get the page bye.net, I don't even get the default fallback page which gets executed when a person enters IP address but not the domain name. I use Windows 7 (server 2) and Windows XP (server 1) UPDATE: I needed to remove DocumentRoot "g:/wamp/www" line :D it was there by mistake! things are working fine now. But one thing: the URL gets replaced by the local ip address any way to not make that happen?

  Read the article

• MAC addresses on dual-NIC mainboards

  - by Tom O'Connor

  Here's a weird problem. We've got a number of devices with dual-NIC mainboards. Some are Realtek NICs, which suck. Some are Intel e1000s, which don't. I've just noticed on 2 machines, one is an Intel NIC, one is a Realtek, that when I put the MAC address of one machine into the dhcpd.conf file on our DHCP server to get it to PXE boot the machine into a rebuild environment, initially everything is fine. The server gets a DHCP allocation, and PXE boots into the Ubuntu preseed enviroment. On one or two machines, it gets as far as Ubuntu's DHCP network configuration, and fails. If i pull up a busybox shell (on tty2 on the installing machine), and run ip link, I can see that the UP flag is set on the other NIC. Here's some stuff. host xeon16-ghz240-gb48-node1 { hardware ethernet BC:AE:C5:07:1F:18; filename "pxelinux.0"; next-server 192.168.123.80; } That's what's in dhcpd.conf This is what ip link on the evil machine looks like. Only one NIC is actually connected (deliberately). As you can see, the NIC that's in the dhcpd config, is not marked as UP, and the link that is UP, isn't the one in DHCP. So far I've seen this on two brands of dual-NIC configuration. Does anyone know 1) what's causing it, and b) What we can do about it?

  Read the article

• Using dnsmasq for accessing multiple nameservers assigned by DHCP

  - by Ash

  At my work desktop running openSUSE 11.4, I have a local network which gets its address, domain (work.site) and nameservers (10.100.1.1, 10.100.1.2) info through DHCP - which get written into /etc/resolv.conf I get to access the internet using the work network, and these 2 nameservers end up returning the entries for any public domain name lookups on the internet. I also have a private VPN that I end up connecting. The nameserver (10.111.1.1) and domain (private.site) are rarely bound to change for this network, but currently they're pushed by the openVPN client into networkmanager, and which also gets merged with the existing /etc/resolv.conf My resolv.conf ultimately ends up looking like this: search private.site work.site nameserver 127.0.0.1 nameserver 10.111.1.1 nameserver 10.100.1.1 As you can see the 2nd nameserver from my work network was pushed out because of the max 3 entry limitations. It is fine still, but would be a problem if that nameserver goes down for maintenance or something. So I found out that dnsmasq could help me here, and hence I setup dnsmasq just as a local DNS resolver without any DHCP support. So right now this is my /etc/dnsmasq.conf: resolv-file=/etc/resolv.conf server=/private.site/10.111.1.1 server=/1.111.10.in-addr.arpa/10.111.1.1 listen-address=127.0.0.1 bind-interfaces log-queries I've made dnsmasq get the list of nameservers from /etc/resolv.conf since NetworkManager seems to be updating this list correctly (for a max of 3 nameservers). I'm able to resolve the host names in both the networks correctly. So these are the questions I have: Is there a way I can make either NetworkManager or dhclient write out the list of nameservers somewhere else which I can make dnsmasq use as resolv-file ? How do I make dnsmasq use certain nameservers as the default for all queries ? Right now I notice that lookups for public domains on the internet are usually sent to both the nameservers - the one on work.site as well as private.site. It would be good if I can limit this only to work.site.

  Read the article

• Computer speakers receive radio station signal

  - by squircle

  I have a set of Logitech 5.1 speakers where each speaker and the source plug into the subwoofer. I'm using a Griffin Firewave with output from my MacBook Pro, and output from my custom-built desktop with a switch in the middle (built it myself out of an old Belkin A/B parallel switch). Recently, I've noticed that I can hear a local Punjabi radio station being picked up by my speakers, and the volume of this interference increases as I increase the volume of the speakers. I'm fairly sure that this radio station is at the low-end of the FM spectrum, below 90MHz (or it may be at the high end, above 105MHz, my memory isn't infallible). It gets quite annoying as I can't put my audio very loud without the interference. I've tried to put a ferrite core on the input cable just before the 3.5mm jacks plug into the subwoofer. I don't know if putting the same core around all three of the cables (green, black, orange) would negate the effects, but I'm assuming not. There has been no change. Is there any reason why this would be happening? I'm assuming the interference is coming somewhere between the FireWave and the subwoofer, because the noise gets amplified with volume increases. If anybody has any suggestions, I'd be grateful!

  Read the article

• How to list rpm packages/subpackages sorted by total size

  - by smci

  Looking for an easy way to postprocess rpm -q output so it reports the total size of all subpackages matching a regexp, e.g. see the aspell* example below. (Short of scripting it with Python/PERL/awk, which is the next step) (Motivation: I'm trying to remove a few Gb of unnecessary packages from a CentOS install, so I'm trying to track down things that are a) large b) unnecessary and c) not dependencies of anything useful like gnome. Ultimately I want to pipe the ouput through sort -n to what the space hogs are, before doing rpm -e) My reporting command looks like [1]: cat unwanted | xargs rpm -q --qf '%9.{size} %{name}\n' > unwanted.size and here's just one example where I'd like to see rpm's total for all aspell* subpackages: root# rpm -q --qf '%9.{size} %{name}\n' `rpm -qa | grep aspell` 1040974 aspell 16417158 aspell-es 4862676 aspell-sv 4334067 aspell-en 23329116 aspell-fr 13075210 aspell-de 39342410 aspell-it 8655094 aspell-ca 62267635 aspell-cs 16714477 aspell-da 17579484 aspell-el 10625591 aspell-no 60719347 aspell-pl 12907088 aspell-pt 8007946 aspell-nl 9425163 aspell-cy Three extra nice-to-have things: list the dependencies/depending packages of each group (so I can figure out the uninstall order) Also, if you could group them by package group, that would be totally neat. Human-readable size units like 'M'/'G' (like ls -h does). Can be done with regexp and rounding on the size field. Footnote: I'm surprised up2date and yum don't add this sort of intelligence. Ideally you would want to see a tree of group-package-subpackage, with rolled-up sizes. Footnote 2: I see yum erase aspell* does actually produce this summary - but not in a query command. [1] where unwanted.txt is a textfile of unnecessary packages obtained by diffing the output of: yum list installed | sed -e 's/\..*//g' > installed.txt diff --suppress-common-lines centos4_minimal.txt installed.txt | grep '>' and centos4_minimal.txt came from the Google doc given by that helpful blogger.

  Read the article

• NetBackup prefers "Scratch" tapes over dedicated tapes

  - by wfaulk

  I have a NetBackup 6.0MP7 installation running on Windows Server 2003. It functions as the only Master Server and Media Server. I swap a full set of tapes in and out every week, but leave a set of tapes with their Volume Pool set to "Scratch" in all the time. The weekly tape sets then get rotated back in after a period of time. Largely, this works fine. I seldom actually need the scratch tapes, but every once in a while, a backup will run over what I have dedicated to the task. However, one week's set of tapes consistently gets declined in favor of the scratch pool. The backup policies are the same for every week, they all have "Policy Volume Pool" set to "NetBackup", and all of the tapes for every week (beside the scratch tapes) have had their pools assigned as "NetBackup", definitely including the week that always gets ignored. That said, it doesn't ignore all of the NetBackup pool tapes for that week. It does usually write to two or three of them, but it writes to like 20 of the scratch tapes. (I haven't thought to look to see if it's always the same two or three tapes.) And this problem never seems to occur for any other week. It doesn't load the tapes and then reject them; it never seems to try to use them at all. They are not flagged as frozen. They are all active and unassigned when I swap them in. The tapes are in a Quantum PX510 tape library. The NetBackup server is attached to the library/robot via fibrechannel going through an HP-branded Brocade switch. I'm not an expert on NetBackup at all. I don't really even know where to look. Any advice on logs to look at or logging to enable or really anything at all would be appreciated. I'll keep an eye on the question and update it if anyone needs any more info to help.

  Read the article

• LAN->LAN IP translation (for TortoiseSVN + Artifacts + Buffalo router)

  - by Armchair Bronco

  Here's my scenario: I've got a VisualSVN server on my main dev box @ home. I'm also using Visual Studio 2010, TortoiseSVN, VisualSVN client (for source control), and Versioned 'Artifacts' (for bug tracking). (I had to modify the fake URL's below to use only one slash because as a new user, I can't post more than one real URL.) I've got my Buffalo AirStation WHR-HP-G300N router properly configured so my business partner can connect to the SVN server. I have port forwarding enabled for the internet-side IP address (like http:/99.888.77.66:443) which gets forwarded to an internal IP (like 192.168.11.6). This part is working great. The problem I'm having is with the integration piece between TortoiseSVN and my bug tracking system. I need to provide a bugtraq:url property, but I haven't been able to get relative paths to work. So I'm forced to use an absolute URL. On my end, I need to use the name of my server (for example: bugtraq:url = https:/my-server/svn/bla..), but this doesn't work for my partner. He needs to specify the IP address (for example: bugtraq:url = https:/999.888.77.66:443/svn/bla...) Is there a way to configure my router such that the IP address for this parameter gets re-routed/re-mapped to "https://my-server" if the request originates from the LAN itself? My router's software supports LAN-Internet and Internet-LAN, but I don't see LAN-LAN.

  Read the article

• Networking problems in VMWare with wireless bridge

  - by Robert Koritnik

  Barebone data: virtualization: VMWare Workstation 6.5 (latest) Host: Windows Server 2008 x64 Guest: Windows Server 2008 x86 Host network adapter: wireless Guest network adapter 1: over Bridge VMNet (automatic) Guest network adapter 2: over Host only VMNet Problem When I surf the net within VM my internet connection just gets stalled (not dropped). It doesn't experience any timeout whatsoever, it just stops downloading/communicating. For instance: I start downloading a file with a browser (IE/FF/CR doesn't matter) and I have to pause/restart download when speed drops to 0. I could wait indefinitelly but connection won't pickup automatically. What did I miss in my network configuration? Update 1 I've tested this in various combinations. This works fine when host is connected via Ethernet. But when connected via Wifi, the connection on the guest works as previously described. It connects fine. It gets a valid IP from DHCP... Everything is cool as long as you don't start doing some intensive network traffic (ie. download a 2MB file) In this case it starts downloading and stops after a while. Speed just drops to 0B/s... Sometimes it picks up back, sometimes it doesn't. Connection still stays and works. I can ping around with no problem.

  Read the article

• Body of email breaks distribution list in exchange?

  - by widgisoft

  Hi, I have a very odd problem that I'm not sure is a programming issue or a server issue :-p. Basically I'm sending an email to an exchange distribution list that includes a PHP stack trace; during certain faults the trace includes really high level information such as the machine's environment variables (during file reads, etc.). I went through a copy of the email line by line until the email sent and it appears the line: [SUDO_COMMAND] => /etc/init.d/httpd restart is the culprit. Adding a string replacement in before the email is sent allows a successful send. What I don't understand is WHY these stream of characters are causing the issue ONLY on the distribution email. If I send the email to myself as well, i.e. "[email protected]; [email protected]", then I get the email fine. Re-ordering the list doesn't make a difference the group never gets the email. Because the individual gets the email and not the group I'm assuming the fault is with exchange and some rogue filtering - I've gone through it with the sysadmins and there's no filtering of any sort on that group... so maybe it's a bug? I can't find anyone else having recorded this specific fault so I figured I'd open it here. For now I'm just not using the distribution list but it'd be nice to eventually find the solution. Many thanks, Chris

  Read the article

• Subversion all or nothing access to repo tree

  - by Glader

  I'm having some problems setting up access to my Subversion repositories on a Linux server. The problem is that I can only seem to get an all-or-nothing structure going. Either everyone gets read access to everything or noone gets read or write access to anything. The setup: SVN repos are located in /www/svn/repoA,repoB,repoC... Repositories are served by Apache, with Locations defined in etc/httpd/conf.d/subversion.conf as: <Location /svn/repoA> DAV svn SVNPath /var/www/svn/repoA AuthType Basic AuthName "svn repo" AuthUserFile /var/www/svn/svn-auth.conf AuthzSVNAccessFile /var/www/svn/svn-access.conf Require valid-user </Location> <Location /svn/repoB> DAV svn SVNPath /var/www/svn/repoB AuthType Basic AuthName "svn repo" AuthUserFile /var/www/svn/svn-auth.conf AuthzSVNAccessFile /var/www/svn/svn-access.conf Require valid-user </Location> ... svn-access.conf is set up as: [/] * = [/repoA] * = userA = rw [/repoB] * = userB = rw But checking out URL/svn/repoA as userA results in Access Forbidded. Changing it to [/] * = userA = r [/repoA] * = userA = rw [/repoB] * = userB = rw gives userA read access to ALL repositories (including repoB) but only read access to repoA! so in order for userA to get read-write access to repoB i need to add [/] userA = rw which is mental. I also tried changing Require valid-user to Require user userA for repoA in subversion.conf, but that only gave me read access to it. I need a way to default deny everyone access to every repository, giving read/write access only when explicitly defined. Can anyone tell me what I'm doing wrong here? I have spent a couple of hours testing and googling but come up empty, so now I'm doing the post of shame.

  Read the article

• Why does "commit" appear in the mysql slow query log?

  - by Tom

  In our MySQL slow query logs I often see lines that just say "COMMIT". What causes a commit to take time? Another way to ask this question is: "How can I reproduce getting a slow commit; statement with some test queries?" From my investigation so far I have found that if there is a slow query within a transaction, then it is the slow query that gets output into the slow log, not the commit itself. Testing In mysql command line client: mysql begin; Query OK, 0 rows affected (0.00 sec) mysql UPDATE members SET myfield=benchmark(9999999, md5('This is to slow down the update')) WHERE id = 21560; Query OK, 0 rows affected (2.32 sec) Rows matched: 1 Changed: 0 Warnings: 0 At this point (before the commit) the UPDATE is already in the slow log. mysql commit; Query OK, 0 rows affected (0.01 sec) The commit happens fast, it never appeared in the slow log. I also tried a UPDATE which changes a large amount of data but again it was the UPDATE that was slow not the COMMIT. However, I can reproduce a slow ROLLBACK that takes 46s and gets output to the slow log: mysql begin; Query OK, 0 rows affected (0.00 sec) mysql UPDATE members SET myfield=CONCAT(myfield,'TEST'); Query OK, 481446 rows affected (53.31 sec) Rows matched: 481446 Changed: 481446 Warnings: 0 mysql rollback; Query OK, 0 rows affected (46.09 sec) I understand why rollback has a lot of work to do and therefore takes some time. But I'm still struggling to understand the COMMIT situation - i.e. why it might take a while.

  Read the article

• Limiting bandwith on an Windows 7 machine

  - by Mihai Damian

  I need to limit the bandwidth on my Windows 7 x64 machine. In the past (on XP) I've been able to use NetLimiter for similar tasks. However for some reason I can't get it to work anymore. For lower limits the bandwidth tests are able to exceed the limit by 10-50%; higher limits seem to be ignored completely and the bandwidth tests report download speeds of over 10 times the speed I set. I'm using speedtest.net and some similar service from my ISP for these tests. Anyway, I don't necessarily need a program as complex as NetLimiter since I only need to throttle my machine's bandwidth, not a specific program's. In case you are wondering why in the world I'd want to cripple my Internet speed, there is a funny story behind this. Long story short, my modem gets random disconnects. Tech support comes in, says my Internet speed is abnormally high and I must be using some tools to somehow make it go faster than it's supposed to and this messes up my modem. I check the connection with another computer and it seems that my PC is the only one in my network that gets abnormal speeds. I reinstall my OS, speed looks normal at first, after I install the batch of 50 or so updates, it goes back to abnormally high speeds and the disconnect problems are not solved. Now I don't have a clue if the explanation the tech team gave me was just a strategy to lay the blame on someone else, but I was trying to give them the benefit of the doubt and see what happens if I really reduce my speed to their specification. Any help appreciated.

  Read the article

• Output Caching with IIS7 - How To for an dynamic aspx page?

  - by Lieven Cardoen

  I have a RetrieveBlob.aspx that gets some query string variables and returns an asset. Eeach url corresponds to a unique asset. In the RetrieveBlob.aspx a Cache Profile is set. In Web.Config the profile looks like (under system.web tag: <caching> <outputCache enableOutputCache="true" /> <outputCacheSettings> <outputCacheProfiles> <add duration="14800" enabled="true" varyByParam="*" name="AssetCacheProfile" /> </outputCacheProfiles> </outputCacheSettings> </caching> Ok, this works fine. When I put a breakpoint in the code behind of RetrieveBlob.aspx, it gets triggered the first time, and all the other times not. Now, I throw away the Cache Profile and instead I'm having this in my Web.Config under System.WebServer: <caching> <profiles> <add extension=".swf" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".flv" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".gif" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".png" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".mp3" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".jpeg" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".jpg" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> </profiles> </caching> Now the caching doesn't work anymore. What am I doing wrong? Is it possible to configure under Caching tag of System.WebServer a Caching Profile for a Dynamic aspx page?

  Read the article

• Windows 7 Loading Very Slow

  - by Adnan

  Hi guys, I've had a problem that only started to occur yesterday. When I boot into Windows 7 and log on to my user account, the computer gets very laggy and slow for at least 5 minutes. Icons take ages to load, and everything is rendered unclickable. This happens for about five minutes after which everything goes back to normal. I tried restarting a few times to see if this is a recurring problem, and it is. I ran a full system scan with Microsoft Security Essentials and found nothing wrong, and I also defragmented the disk to increase performance. However, the problem still exists. Edit: For the past day, I've been trying to install Ubuntu on the same laptop. When installing it on a partition didn't work, I decided to use Wubi. Could this somehow be the problem? Also, my hard drive gets hot a lot, so could the heat be affecting the hard drive and maybe making it defective? Any help on this issue would be greatly, greatly appreciated.

  Read the article

• Menu command stuck on screen

  - by 280Z28

  For some reason, periodically when I select a menu command, the command label gets "stuck" on the screen and won't go away. I can close all open applications, including whichever one I was using when it got stuck, but it still won't go away. In the screenshot below, I opened an new instance of IE just to show how the label stays on top. The label was not created by this instance of IE. Edit with the source: The label that gets stuck is the first menu command I select in IE. If a label is already stuck, a new one does not get stuck (regardless of which instance(s) of IE are involved). Based on this knowledge, I now just open IE on my secondary monitor, carefully open the context menu so the Properties command is in the bottom corner, and click it. This is not a solution... The label never moves and is transparent to mouse input (if I click it, it's as if I clicked the item behind it). The label does not go away if I close all running applications. I haven't tried stopping services or closing system tray items like Live Mesh. The label does go away if I change the screen resolution and then change it back. Any ideas how I can stop this from happening? It's happened a half dozen times since yesterday and it's becoming quite disrupting to my work. Obviously I added the circle in MS Paint. That part isn't stuck. ;)

  Read the article

• Computer causing WiFi interference?

  - by Mannimarco

  I came back from college and brought my desktop computer. Family recently switched to Verizon FIOS and got a new router because of it. Unfortunately, my connection to the new wifi network is awful, with the download speeds (tested through speedtest.net) fluctuating wildly and often dropping below 1.5 Mbps. A laptop in the same room gets 20 Mbps. I've tried a new wireless card, thinking that mine got damaged in the move home but no luck. Here's where it gets weird: if I place the laptop near the computer, the laptop's download speeds often suffer greatly. Pulling the laptop away always fixes this. So now I'm under the impression that there's something in the computer (which I built a year ago and has had 0 issues up to this point) is causing an insane amount of wireless interference. Also bizarre: the upload speeds seem unaffected by this problem. On the laptop and desktop, upload speeds are generally around 5 Mpbs. Any ideas as to what could be causing this and how to test said theories would be fantastic.

  Read the article

• Networking problems in VMWare with wireless bridge

  - by Robert Koritnik

  Barebone data: virtualization: VMWare Workstation 6.5 (latest) Host: Windows Server 2008 x64 Guest: Windows Server 2008 x86 Host network adapter: Ethernet (see comment) Host network adapter: Wireless (see comment) Guest ethernet network adapter 1: Bridged VMNet (automatic) Guest ethernet network adapter 2: Host only VMNet comment: my host has LAN and Wifi but only one at the same time. I'm either wired or wireless. Never both. So bridged connection on VM goes either via wire or air. Problem When I'm wirelessly connected on the host and I access internet within VM my connection just gets stalled (not dropped). It doesn't experience any timeout whatsoever, it just stops downloading/communicating. For instance: I start downloading a file with a browser (IE/FF/CR doesn't matter) and I have to pause/restart download when speed drops to 0. I could wait indefinitely but connection won't pick-up automatically. What did I miss in my network configuration? Update 1 I've tested this in various combinations. This works fine when host is connected via Ethernet. But when host is connected via Wifi, the connection on the guest works as previously described. It connects fine. It gets a valid IP from DHCP... Everything is cool as long as you don't start doing some intensive network traffic (ie. download a 2MB file) In this case it starts downloading and stops after a while. Speed just drops to 0B/s... Sometimes it picks up back, sometimes it doesn't. Connection still stays and works. I can ping around with no problem.

  Read the article

• NETKEY IPsec and ARP

  - by Shawn J. Goff

  I'm wondering if I have the correct routing setup for an IPsec tunnel. I have control over the IPsec endpoints and the hosts connected to one side. These hosts are connecting to the tunnel so that they have access to the network on the other side of what I will call the IPsec server. I don't have control of the network upstream of this server. Normally, the IPsec server will not respond to ARP requests for the hosts on the other side of the tunnel. So when a packet arrives for one of my hosts the server gets ARP requests, but the upstream router gets no response, and cannot construct the ethernet frame to send me the packets. If I was using one of the swan stacks, I would have a separate interface, and I'd probably just need to turn on proxyarp, but I'm using NETKEY, which doesn't use a separate interface for the tunnel. To solve the problem for now, I have added an eth0.5 vlan to the IPsec server, turned on proxyarp for that interface, and added all routes my hosts addresses to that interface so that it will respond to those ARP requests (and will therefore get relevant packets routed to it). This works, but it feels wrong. What is the correct way to get the upstream router to send me the traffic for these hosts?

  Read the article

• windows Home Server backup error

  - by domen

  I've finally built my WHS, but some other problems have showed up. I've googled, binged and searched SU with no success. The problem is following: at the moment I've got a Win7 laptop and Win7 PC, which should be backed up by the WHS. Laptop is backed up just fine with no issues, but when I try to manually backup the PC, after "backup is starting" message, when backup service should be monitoring changes on partitions, PC gets disconnected from the home network and thus, the backup process is stuck. Disabling/enabling network adapter gets PC back on the network. The only thing I've tried was reinstalling connector software. no success. Also, I've downloaded connector troubleshooter and only thing it says is "DHCP server was not found". I'm not good with networks, so I couldn't figure out what could that indicate (all computers in the network are assigned static IPs). Any ideas what the problem can be? I can provide any additional information, I'm just not sure what may be helpful right now. Thanks.

  Read the article

• Conky starts above windows in Ubuntu Maverick

  - by DesertIvy

  Hey guys, I did not run into this problem until I upgraded my Ubuntu box to Maverick Meerkat (10.10). Basically, whenever I start my computer, conky runs as expected, except it gets drawn over any windows that I load (see screenshot). To fix this for a single session, I simply restart conky by running killall conky; conky in a terminal. Conky gets re-drawn below active windows (namely, only appearing on my desktop), and does not have the border/drop-shadow, but I have to do this every time I start a new session. Is there a simple way to fix this? I have a small shell script that I run on startup, but it does not seem to solve the problem. #!/bin/bash sleep 10 && conky; sleep 5 && killall conky; conky; Below is the non-text part of my .conkyrc file. # Conky settings # background yes update_interval 1 cpu_avg_samples 2 net_avg_samples 2 override_utf8_locale yes double_buffer yes no_buffers yes text_buffer_size 2048 #imlib_cache_size 0 temperature_unit fahrenheit # Window specifications # own_window yes own_window_type override own_window_transparent yes own_window_hints undecorate,sticky,skip_taskbar,skip_pager,below border_inner_margin 0 border_outer_margin 0 minimum_size 200 250 maximum_width 200 alignment tr gap_x 220 gap_y 280 # Graphics settings # draw_shades no draw_outline no draw_borders no draw_graph_borders no # Text settings # use_xft yes xftfont caviar dreams:size=8 xftalpha 0.5 uppercase no temperature_unit celsius default_color FFFFFF # Lua Load # lua_load ~/.lua/scripts/clock_rings.lua lua_draw_hook_pre clock_rings

  Read the article

• Will just a couple of thermal "trip" shutdowns typically damage a CPU?

  - by T.J. Crowder

  The short version If a CPU gets so hot that the system turns itself off because of a thermal trip signal just a couple of times, is it likely that the CPU will be damaged? Or does the trip do its job, turning it off before the CPU gets damaged? (This is with all default settings in the BIOS; I haven't raised any temp thresholds or overclocked anything.) The longer version I just got this Intel Atom D510-based fanless system, installed a 2.5" mobile SATA drive and two 2GB PC2-6400s, closed it up, and having checked everything was recognized in the BIOS, set about installing Ubuntu. After a couple of false starts related, I think, to the external DVD drive I was using, I got the install happily running along. About three-fourths or so of the way through the install, having been running less than an hour, the machine turned itself off. I was actually out of the room at the time, but when I came back and turned it back on, it said it had shut down due to a thermal event. I went into the BIOS and saw that (at that point, having just been turned back on after a couple of minutes off), it was running 87C. As near as I can tell from Intel's docs (PDF here), the max "junction" temperature for the CPU is 100C and it will raise a THERMTRIP signal at 125C. Yowsa. Presumably there will be some back-and-forth with the vendor on this, I'm just wondering whether letting it get that hot a couple of times is likely to end up damaging it.

  Read the article

• how to automatically mount ~/Private using ecryptfs when logging in via ssh pubkey

  - by andreash

  Raionale: I want to be able to automatically make backups to a remote machine, which will be encrypted with ecryptfs. The title says it all: I set up ecryptfs-utils on my Debian Squeeze box, and set up one user to use it via ecryptfs-setup-private. When I log in via SSH using password authentication, the ~/Private directory automatically gets mounted. How can I achieve that ~/Private also automatically gets mounted when logging in via SSH using public key authentication? Obviously, the best solution would be if ecryptfs could somehow 'use' the SSH public key to en/decrypt the data (I know that then using the user's password would not be able to en/decrypt the data any more; this would be acceptable). Probably, this will not work. So perhaps somehow call ecryptfs-mount-private via ssh before logging in via public key? Probably, then I would need to somehow pipe the passphrase through the SSH connection, right? So I would need to store it on the source machine's file system. Not nice either. Any other ideas?

  Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >