Search Results

Search found 1886 results on 76 pages for 'vendor neutrality'.

Page 59/76 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

• Setting my NIC to full duplex

  - by David

  I am trying to optimize the network speed of my Solaris X86 server, and have discovered that the Cisco 3548 that it is connected to has issues with the NIC in my server. The NIC appears to have not been configured fully, and is coming up 100 half-duplex. The 3548 ports are all set to 100 full. Ideally I'd like to have the server set for 100 full, and have been attempting to configure it using ndd commands. However I have had no results. The following command: -bash-3.00# dladm show-dev rtls0 link: unknown speed: 100 Mbps duplex: unknown The NIC shows up as: pci bus 0x0001 cardnum 0x06 function 0x00: vendor 0x10ec device 0x8139 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ which should be configurable. I have modified the configuration file from auto config (5) to 100 fdx (4) to no avail. If there is no other choice, I could alter the Cisco 3548 to be 100 half-duplex. However, this solution causes huge performance loss. Currently throughput is about 500Kbps, when it should be around 40Mbps.

  Read the article

• Lenovo S110 netbook screen resolution Ubuntu

  - by Neigyl R. Noval

  I am still stuck with 800x600 resolution. Here is the output of lspci: 00:00.0 Host bridge: Intel Corporation Device 0bf2 (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Device 0be2 (rev 09) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation N10/ICH7 Family SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8176 (rev 01) Also, I tried modifying /usr/lib/X11/xorg.conf.d/10-monitor.conf to fix this problem, but still does not work: Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Screen" Identifier "Screen0" Monitor "Monitor0" Device "Card0" SubSection "Display" Viewport 0 0 Depth 1 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 4 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 8 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 15 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 16 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 24 Modes "1024x768" EndSubSection EndSection Section "Device" Identifier "Card0" Driver "vesa" VendorName "Intel Corporation Device" EndSection I'm using Gnome. System Preference Monitor screen resolution sticks to 800x600. What am I going to do?

  Read the article

• Is StoreJet Transcend (0x2329) an Advanced Format drive?

  - by Graham Perrin

  I use a 640 GB StoreJet Transcend (0x2329) with ZEVO Community Edition 1.1.1 on OS X 10.8.2. Question Is this drive Advanced Format? Background I submitted a request for technical support to Transcend but the first response was gibberish so I don't expect a reasonable follow-up. Models at http://www.transcend-info.com/Products/CatList.asp?LangNo=0&ModNo=293 are similar but different sizes (not 640 GB). Mine is probably 25M2 (TS640GSJ25M2): Unless I'm missing something, nothing currently in the Transcend support area tells me whether the drive is Advanced Format. From System Information in OS X 10.8.2: StoreJet Transcend: Capacity: 640.14 GB (640,135,028,736 bytes) Removable Media: Yes Detachable Drive: Yes BSD Name: disk3 Product ID: 0x2329 Vendor ID: 0x152d (JMicron Technology Corp.) Version: 0.00 Serial Number: 322549FBA004 Speed: Up to 480 Mb/sec Manufacturer: JMicron History for the ZFS pool shows creation in March 2012 –  macbookpro08-centrim:~ gjp22$ zpool history zhandy | grep create 2012-03-14.17:29:37 zpool create -f -O compression=off -O copies=1 -O casesensitivity=insensitive -O snapdir=visible zhandy /dev/dsk/GPTE_1928482A-7FE4-482D-B692-3EC6B03159BA 2012-06-22.15:51:16 zfs create zhandy/Pocket Time Machine At that time I almost certainly used ZEVO Setup Assistant to create the pool. macbookpro08-centrim:~ gjp22$ zpool get ashift zhandy NAME PROPERTY VALUE SOURCE zhandy ashift 0 default If I discover that the drive is Advanced Format, a different ashift value will be appropriate.

  Read the article

• RPM issues after signing JDK 1.6 64-bit

  - by organicveggie

  I'm trying to sign the Java JDK 1.6u21 64-bit RPM on CentOS 5.5 for use with Spacewalk and I'm running into problems. It seems to sign okay, but then when I check the signature it seems to be missing the key I just used to sign it. Yet RPM shows the key in it's list... # rpm --addsign jdk-6u21-linux-amd64.rpm Enter pass phrase: Pass phrase is good. jdk-6u21-linux-amd64.rpm: gpg: WARNING: standard input reopened gpg: WARNING: standard input reopened # rpm --checksig -v jdk-6u21-linux-amd64.rpm jdk-6u21-linux-amd64.rpm: Header V3 DSA signature: NOKEY, key ID ecfd98a5 MD5 digest: OK (650e0961e20d4a44169b68e8f4a1691b) V3 DSA signature: OK, key ID ecfd98a5 Yet I have the key imported (edited for privacy): # rpm -qa gpg-pubkey* |grep ecfd98a5 gpg-pubkey-ecfd98a5-4caa4a4c # rpm -qi gpg-pubkey-ecfd98a5-4caa4a4c Name : gpg-pubkey Relocations: (not relocatable) Version : ecfd98a5 Vendor: (none) Release : 4caa4a4c Build Date: Mon 04 Oct 2010 10:20:49 PM CDT Install Date: Mon 04 Oct 2010 10:20:49 PM CDT Build Host: localhost Group : Public Keys Source RPM: (none) Size : 0 License: pubkey Signature : (none) Summary : gpg(FirstName LastName <[email protected]>) Description : -----BEGIN PGP PUBLIC KEY BLOCK----- Version: rpm-4.4.2.3 (NSS-3) ...key goes here... =gKjN-----END PGP PUBLIC KEY BLOCK----- And I'm definitely running a 64-bit version of CentOS: # uname -a Linux spacewalk.mycompany.corp 2.6.18-194.11.4.el5 #1 SMP Tue Sep 21 05:04:09 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux Without a valid signature, Spacewalk refuses to install the RPM unless I completely disable signature checking. I have tried this with two different keys and two different users on the same machine without any success. Any bright ideas?

  Read the article

• What does this mean: "SATP VMW_SATP_LOCAL does not support device configuration"?

  - by Jason Tan

  Can anyone tell me what this means in ESXi 5.1?: SATP VMW_SATP_LOCAL does not support device configuration I've googled it and I get a lot of results, but as yet all the pages that contain the string are discussing other matters. The storage array is a HDS HUS-VM and the hosts are HP b460c G8 blades with flex fabric and flex fabric VCs which I am in the process of commissioning and would like to get it started on the right foot - i.e. error and warning free! naa.600508b1001c56ee3d70da65f071da23 Device Display Name: HP Serial Attached SCSI Disk (naa.600508b1001c56ee3d70da65f071da23) Storage Array Type: VMW_SATP_LOCAL Storage Array Type Device Config: SATP VMW_SATP_LOCAL does not support device configuration. Path Selection Policy: VMW_PSP_FIXED Path Selection Policy Device Config: {preferred=vmhba0:C0:T0:L1;current=vmhba0:C0:T0:L1} Path Selection Policy Device Custom Config: Working Paths: vmhba0:C0:T0:L1 Is Local SAS Device: true Is Boot USB Device: false This is the same LUN: ~ # esxcli storage core device list -d naa.60060e80132757005020275700000016 naa.60060e80132757005020275700000016 Display Name: HITACHI Fibre Channel Disk (naa.60060e80132757005020275700000016) Has Settable Display Name: true Size: 204800 Device Type: Direct-Access Multipath Plugin: NMP Devfs Path: /vmfs/devices/disks/naa.60060e80132757005020275700000016 Vendor: HITACHI Model: OPEN-V Revision: 5001 SCSI Level: 2 Is Pseudo: false Status: degraded Is RDM Capable: true Is Local: false Is Removable: false Is SSD: false Is Offline: false Is Perennially Reserved: false Queue Full Sample Size: 0 Queue Full Threshold: 0 Thin Provisioning Status: unknown Attached Filters: VAAI_FILTER VAAI Status: supported Other UIDs: vml.020001000060060e801327570050202757000000164f50454e2d56 Is Local SAS Device: false Is Boot USB Device: false ~ #

  Read the article

• How do hdparm's -S and -B options interact?

  - by user697683

  These two options seem confusing. For example: according to the man page -B 254 "does not permit spin-down". However, testing with -B 254 -S 1 the drive does spin down after 5 seconds. -B Query/set Advanced Power Management feature, if the drive supports it. A low value means aggressive power management and a high value means better performance. Possible settings range from values 1 through 127 (which permit spin-down), and values 128 through 254 (which do not permit spin-down). The highest degree of power management is attained with a setting of 1, and the highest I/O performance with a setting of 254. A value of 255 tells hdparm to disable Advanced Power Management altogether on the drive (not all drives support disabling it, but most do). -S Put the drive into idle (low-power) mode, and also set the standby (spindown) timeout for the drive. This timeout value is used by the drive to determine how long to wait (with no disk activity) before turning off the spindle motor to save power. Under such circumstances, the drive may take as long as 30 seconds to respond to a subsequent disk access, though most drives are much quicker. The encoding of the timeout value is somewhat peculiar. A value of zero means "timeouts are disabled": the device will not automatically enter standby mode. Values from 1 to 240 specify multiples of 5 seconds, yielding timeouts from 5 seconds to 20 minutes. Values from 241 to 251 specify from 1 to 11 units of 30 minutes, yielding timeouts from 30 minutes to 5.5 hours. A value of 252 signifies a timeout of 21 minutes. A value of 253 sets a vendor-defined timeout period between 8 and 12 hours, and the value 254 is reserved. 255 is interpreted as 21 minutes plus 15 seconds. Note that some older drives may have very different interpretations of these values.

  Read the article

• Fully FOSS EMail solution

  - by Ravi

  I am looking at various FOSS options to build a robust EMail solution for a government funded university. Commercial options are to be chosen only in the worst case scenario. Here are the requirements: Approx 1000-1500 users - Postfix or Exim? (Sendmail is out;-)) Mailing lists for different groups/Need web based archive - Mailman? Sympa? Centralised identity store - OpenLDAP? Fedora 389DS? Secure IMAP only - no POP3 required - Courier? Dovecot? Cyrus?? Anti Spam - SpamAssasin? what else? Calendaring - ?? webmail - good to have, not mandatory - needs to be very secure...so squirrelmail is out;-)? Other questions: What mailbox storage format to use? where to store? database/file system? Simple and effective HA options? Is there a web proxy equivalent to squid in the mail server world? software load balancers?CARP? Monitoring and alert? Backup? The govt wants to stimulate the local economy by buying hardware locally from whitebox vendors. Also local consultants and university students will do the integration. We looked at out-of-the-box integrated solutions like Axigen, Zimbra and GMail but each was ruled out in favour of a DIY approach in the hopes of full control over the data and avoiding vendor lockin - which i though was a smart thing to do. I wish more provincial governments in the developing world think of these sort of initiatives As for OS - Debian, FreeBSD would be first preference. Commercial OS's need not apply. CentOS as second tier option...

  Read the article

• Replacing all disks in a non-OS RAID 5 volume

  - by molecule

  Hi all, We currently have a server with 8 x HDD slots. It is a HP DL380G5 with a P400 controller. 2 x HDD are in a RAID 1+0 config and this hosts the OS. 6 x HDD are in a RAID 5 config and holds an Oracle DB. Basically the RAID 5 volume is running out of space and we would like to swap all 6 with higher capacity disks. Excuse my ignorance as I am pretty new to this... I believe we will need to backup the data, delete the RAID volume, insert the new disks, recreate the volume, and restore the data. 2 questions: Do we need to worry about the OS partition or is it completely independent so we can simply take out the 6 and insert 6 new disks and get the controller to recognize the 6 new disks and form a new RAID 5 volume? We should not need to reinstall OS or Oracle correct? Since we are going to restore the data on the volume from another source (our vendor will take care of this) but we would like to keep the existing data on the 6 disks just in case we run into issues and want to fall back, is this possible? Thanks in advance.

  Read the article

• windows xp blue screen dumping physical memory

  - by dotnet-practitioner

  I get following blue screen after running my laptop for an hour... A problem has been detected and windows has been shut down to prevent damange to your computer. If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to be sure you have adequate disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters. Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as cashing or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and the select safe mode. Technical Information: * STOP 0x0000008E (0xc0000005, 0x805B03F5, 0xF703DC7C, 0x00000000) Beginning dump of physical memory Physical memory dump complete. Contact you system administrator or technical support group for further assistance. so.... if this is a faulty memory.... from where I could buy RAM for following laptop.... TOSHIBA SATELLITE A45-S250 My local Frys store does not carry memory for this laptop.

  Read the article

• Utility to LOGICALLY compare two xml files?

  - by Matthew

  Right now we are attempting to build golden configurations for our environment. One piece of software that we use relies on large XML files to contain the bulk of its configuration. We want tot ake our lab environment, catalog it as our "golden configuration" and then be able to audit against that configuration in the future. Since diff is bytewise comparison and NOT logical comparison, we can't use it to compare files in this case (XML is unordered, so it won't work). What I am looking for is something that can parse the two XML files, and compare them element by element. So far we have yet to find any utilities that can do this. OS doesn't matter, I can do it on anything where it will work. The preference is something off the shelf. Any ideas? Edit: One issue we have run into is one vendor's config files will occasionally mention the same element several times, each time with different attributes. Whatever diff utility we use would need to be able to identify either the set of attributes or identify them all as part of one element. Tall order :)

  Read the article

• ipmi - can't ping or remotely connect

  - by Fidel

  I've tried configuring the IPMI controller to accept remote connections, but I can't even ping it. Here is it status: #/usr/local/bin/ipmitool lan print 2 Set in Progress : Set Complete Auth Type Support : NONE PASSWORD Auth Type Enable : Callback : : User : NONE PASSWORD : Operator : PASSWORD : Admin : PASSWORD : OEM : IP Address Source : Static Address IP Address : 192.168.1.112 Subnet Mask : 255.255.255.0 MAC Address : 00:a0:a5:67:45:25 IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10 BMC ARP Control : ARP Responses Enabled, Gratuitous ARP Enabled Gratituous ARP Intrvl : 8.0 seconds Default Gateway IP : 192.168.1.1 Default Gateway MAC : 00:00:00:00:00:00 802.1q VLAN ID : Disabled 802.1q VLAN Priority : 0 RMCP+ Cipher Suites : 0,1,2,3 Cipher Suite Priv Max : uaaaXXXXXXXXXXX : X=Cipher Suite Unused : c=CALLBACK : u=USER : o=OPERATOR : a=ADMIN : O=OEM # /usr/local/bin/ipmitool user list 2 ID Name Enabled Callin Link Auth IPMI Msg Channel Priv Limit 1 true false true true USER 2 admin true false true true ADMINISTRATOR # /usr/local/bin/ipmitool channel getaccess 2 2 Maximum User IDs : 5 Enabled User IDs : 2 User ID : 2 User Name : admin Fixed Name : No Access Available : callback Link Authentication : enabled IPMI Messaging : enabled Privilege Level : ADMINISTRATOR # /usr/local/bin/ipmitool channel info 2 Channel 0x2 info: Channel Medium Type : 802.3 LAN Channel Protocol Type : IPMB-1.0 Session Support : multi-session Active Session Count : 0 Protocol Vendor ID : 7154 Volatile(active) Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available Non-Volatile Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available # /usr/local/bin/ipmitool chassis status System Power : on Power Overload : false Power Interlock : inactive Main Power Fault : false Power Control Fault : false Power Restore Policy : unknown Last Power Event : Chassis Intrusion : inactive Front-Panel Lockout : inactive Drive Fault : false Cooling/Fan Fault : false # arp Address HWtype HWaddress Flags Mask Iface 192.168.1.112 ether 00:A0:A5:67:45:25 C bond0 # /usr/local/bin/ipmitool -I lan -H 192.168.1.112 -U admin -P admin chassis power status Error: Unable to establish LAN session Unable to get Chassis Power Status In summary. It exists on the ARP list so arp's are being broadcast. I can't ping it and can't connect to it. Can anyone spot any glaring mistakes in the configuration? Many thanks, Fidel

  Read the article

• I am looking for a tool to measure or detect "unresponsiveness" of a desktop PC

  - by Tom H

  I have a client that provides some server systems to a hospital, and a support ticket was raised that the desktop application was hanging waiting for the server. We did some extensive testing and its pretty clear that the server is responsive, and the network is fine, and that the problem is on the client end. (no requests are received during the hang etc...) We take a look at the desktop machines and they should be fine, so we raise tickets with the software vendor who says that it must be the hardware, the hardware company says that it is the software, etc etc Anyway, so talking to the nurses, they say that these machines often "hang" for 30 seconds at a time, and sometimes during important moments where they need to get data for a patient who is unwell, such as charts and status. So I want to stick a client on these machines that would be able to detect arbitrary "unresponsiveness" of the keyboard/mouse and log that for analysis later. Obviously I am wary to suggest some application that takes resources and makes the problem even worse, so I would interested to see any tools that would detect these (is it correct to say that the keyboard interrupts are being discarded?) scenarios by looking for the OS discarding the interrupts, or whatever is appropriate here. so go on then serverfault, here is your chance to save a life.... ;-) Edit: I am starting to think that some of the tools associated with real time systems might be appropriate, at least as a diagnostic.

  Read the article

• Drivers and firmware for the LiteOn ihap-122-9 DVD drive

  - by Sandy

  I'm trying to replace the DVD drive in my old PC. LiteOn.com is a mess and I can't find a single working driver or firmware update there, or anywhere. Windows XP tries to use a default, generic driver dated 2001. (About 9 years before this drive even existed.) http://www.firmwarehq.com/download_1..._6L0H.EXE.html This correctly finds my LiteOn ihap-122-9 DVD Drive. It correctly finds that I'm currently using firmware 6L0F. It correctly tries to install 6L0H. It completes 100% but then just fails and says "contact your vendor". Does anyone know why? Where can I actually get drivers... and firmware updates... that actually work for the ihap-122-9? Apparently, the newest driver IS the 1 made 9 years before the drive existed. (Unbelievable.) And the latest firmware is the 1 that is already in the drive. (Common.) No other drive I've had in this computer ever had a problem. This brand new LiteOn is doing this: Opening MY COMPUTER now takes 60 seconds. MY COMPUTER marking the drive as "DVD F:" takes another 30 seconds. MY COMPUTER showing "Batman II" title takes another 15 seconds. Clicking and running the movie will take another 30 seconds for the main-menu to appear. The movie starts about 20 seconds later. The movie runs fine for 1-2 seconds... then stops for 5 seconds.... then starts again and plays for 1-2 seconds. Repeats for 2 hours. (It happens with all store-bought DVDs and all home-made DVDs.)

  Read the article

• Can I format a Veritas cluster shared volume from windows?

  - by spaghettidba

  We have a Microsoft Failover Cluster with dynamic disks managed by Veritas Storage Foundation. Today the sysadmins added a new disk for SQL Server but the cluster size on the volume was wrong, so I issued a quick format to change it. The disk volume failed, the SQL Server group failed as well and the cluster became unresponsive. After some minutes I managed to fail over to a passive node. The SAN admins say it's my fault because I shouldn't have formatted the disk from the Windows format applet, but I should have used Veritas Enterprise Administrator instead. Can a format operation bring offline a whole cluster group this way? Relevant error messages: From the eventlog: The cluster resource host subsystem (RHS) stopped unexpectedly. An attempt will be made to restart it. This is usually due to a problem in a resource DLL. Please determine which resource DLL is causing the issue and report the problem to the resource vendor. From the cluster.log ERR [RCM] rcm::RcmResControl::DoResourceControl: ERROR_RESOURCE_CALL_TIMED_OUT(5910)' because of 'Control(STORAGE_GET_DISK_INFO_EX) to resource 'NameOfTheDiskGroup' timed out.' Veritas Documentation: Excerpt from Symantec's documentation: Note: Before manually creating the resource, you must format the cluster-shared volume with NTFS using the VEA GUI and mount it on the node where you are trying to create the resource. Does this mean the disk cannot be formatted from Windows? I don't read it that way. For the record, I formatted many disks using the Windows applet in the past and nothing bad happened.

  Read the article

• Anyone else experiencing high rates of linux server crashes today?

  - by Bron Gondwana

  Just today, Sat June 30th - starting soon after the start of the day GMT. We've had a handful of blades in different datacentres as managed by different teams all go dark - not responding to pings, screen blank. They're all running Debian Squeeze - with everything from stock kernel to custom 3.2.21 builds. Most are Dell M610 blades, but I've also just lost a Dell R510 and other departments have lost machines from other vendors too. There was also an older IBM x3550 which crashed and which I thought might be unrelated, but now I'm wondering. The one crash which I did get a screen dump from said: [3161000.864001] BUG: spinlock lockup on CPU#1, ntpd/3358 [3161000.864001] lock: ffff88083fc0d740, .magic: dead4ead, .owner: imapd/24737, .owner_cpu: 0 Unfortunately the blades all supposedly had kdump configured, but they died so hard that kdump didn't trigger - and they had console blanking turned on. I've disabled console blanking now, so fingers crossed I'll have more information after the next crash. Just want to know if it's a common thread or "just us". It's really odd that they're different units in different datacentres bought at different times and run by different admins (I run the FastMail.FM ones)... and now even different vendor hardware. Most of the machines which crashed had been up for weeks/months and were running 3.1 or 3.2 series kernels. The most recent crash was a machine which had only been up about 6 hours running 3.2.21.

  Read the article

• Cannot set video resolution above 640x480 after installing Windows XP SP2

  - by waanders

  I've installed Windows XP SP2 on a computer (there was not SP at all). Now the display settings are set back to 640x480 and 4 bits colors. And I can't change it, it's the only option in Settings tab of the Display dialog of Windows. The screen look awful now, how can I solve this problem? UPDATE: Seems to be a problem with the video driver (thanks @Karan and @Hennes). I did run Speccy (PC-Wizard freezes the computer) and this is a part of the log file: Summary Operating System Microsoft Windows XP Professional 32-bit SP3 CPU Intel Celeron Willamette 0.18um Technology RAM 512 MB DDR @ 133MHz (2.5-3-3-6) Motherboard COMPAQ 0838h (FC-478) Graphics Standard Monitor (640x480@1Hz) Hard Drives 19.0GB Maxtor 2B020H1 (PATA) Optical Drives No optical disk drives detected Audio No audio card detected ... Graphics Monitor Name Standard Monitor on Current Resolution 640x480 pixels Work Resolution 640x450 pixels State enabled, primary Monitor Width 640 Monitor Height 480 Monitor BPP 4 bits per pixel Monitor Frequency 1 Hz Device \\.\DISPLAY1 OpenGL Version 1.1.0 Vendor Microsoft Corporation Renderer GDI Generic GLU Version 1.2.2.0 Microsoft Corporation Values GL_MAX_LIGHTS 8 GL_MAX_TEXTURE_SIZE 1024 GL_MAX_TEXTURE_STACK_DEPTH 10 GL Extensions GL_WIN_swap_hint GL_EXT_bgra GL_EXT_paletted_texture GL_EXT_bgra

  Read the article

• Configuration for httphandler in classic mode

  - by happyspider

  I have to install an httphandler that needs to run on classic mode. I have created an application on the iis that uses a classic apppool and put the handler assembly there. The vendor gave me a configuration in the deployment document that looks like this: <system.web> <globalization requestEncoding="iso-8859-1" responseEncoding="iso-8859-1" /> <httpModules> </httpModules> <httpHandlers> <add verb="*" path="*" type="ProductName.ProductName, ProductName" /> </httpHandlers> </system.web> <system.webServer> <validation validateIntegratedModeConfiguration="false"/> <handlers> <add name="someUnspecificName" path="*" verb="*" modules="IsapiModule" scriptProcessor="C:\Windows\Microsoft.NET\Framework\v2.0.50727\aspnet_isapi.dll" resourceType="Unspecified" requireAccess="None" preCondition="classicMode,runtimeVersionv2.0,bitness32" /> </handlers> </system.webServer> The error I get when requesting a URL on the application is a 404, so I guess the handle is not used at all. Does the configuration look ok for a 64bit system?

  Read the article

• Finding custom printer-specific options on *nix

  - by enbuyukfener

  Hey all, I have a printer set up using CUPS (FujiXerox Document Center 1100), it is named DC1100. There are capabilities of the printer that are not shows as options of the printer as listed by: lpoptions -l -d DC1100 The output is below: PrintoutMode/Printout Mode: Draft *Normal High Photo InputSlot/Media Source: Upper Lower MultiPurpose LargeCapacity Manual *Standard PageSize/Page Size: *Letter A4 C5 C6 COM10 DL Executive Legal Monarch Statement PageRegion/PageRegion: Letter A4 C5 C6 COM10 DL Executive Legal Monarch Statement STP_Brightness/Brightness: 0.00 0.02 0.04 [snip] 2.00 STP_Contrast/Contrast: 0.00 0.05 0.10 0.15 [snip] 4.00 STP_ColorCorrection/Color Correction: Accurate Bright Density [snip] Uncorrected STP_DitherAlgorithm/Dither Algorithm: Adaptive EvenTone Fast [snip] VeryFast STP_EnableDensity/Density Enable: *Disabled Enabled STP_Density/Density Value: 0.1 0.2 0.3 0.4 [snip] 8.0 STP_EnableGamma/Composite Gamma Enable: *Disabled Enabled STP_Gamma/Composite Gamma Value: 0.10 0.15 0.20 0.25 [snip] 4.00 STP_LinearContrast/Linear Contrast Adjustment: *False True STP_Duplex/Double-Sided Printing: DuplexNoTumble DuplexTumble *None Resolution/Rendering Resolution: *FromPrintoutMode 150x150dpi 300x300dpi 600x600dpi OutputType/Output Type: *FromPrintoutMode BlackAndWhite Grayscale STP_ImageType/Image Type: *FromPrintoutMode Photo Graphics LineArt None Text TextGraphics STP_Resolution/Resolution: *FromPrintoutMode 150dpi 300dpi 600dpi I am particularly looking for options for: "secure print" (possibly by setting a mode and setting a username) stapling hole punching Perhaps I need a vendor specific driver/PPD file? If so, any pointers as I have no idea where to look for one. I haven't been able to find one on the official site or on sites such as http://www.openprinting.org

  Read the article

• Why Is Volume Shadow Copy Services stopping?

  - by David Mackintosh

  I am running Windows 7 Professional, 64-bit. I am running a backup-over-the-internet software client which depends on the Volume Shadow Copy Services running. Since I installed Service Pack 1 (or rather, didn't object when Windows Update forced Service Pack 1 on me) the backup service is failing to back everything up because VSC isn't running. Most of the time it fails to back up such noise as the Security Essentials database or the Messenger Live contact list -- stuff I really don't care about -- but I don't want to fall into the trap of accepting an Error-state backup as "normal". At the recommendation of the backup software, I have set the VSC service startup mode to be Automatic. When I look in the Event Log, System channel I can see at boot time: The Volume Shadow Copy service entered the running state. ...and then two or three minutes later: The Volume Shadow Copy service entered the stopped state. How do I figure out why VSC is stopping? At the suggestion of the backup vendor, I have already followed the suggestions from http://support.microsoft.com/default.aspx/kb/940184 net stop SENS net stop EventSystem net start EventSystem net start SENS net stop COMSysApp net stop SwPrv net stop VSS cd /d C:\Windows\system32 regsvr32 ole32.dll /s regsvr32 oleaut32.dll /s regsvr32 vss_ps.dll /s vssvc /register /s regsvr32 /i swprv.dll /s regsvr32 /i eventcls.dll /s regsvr32 es.dll /s regsvr32 stdprov.dll /s regsvr32 vssui.dll /s regsvr32 msxml.dll /s regsvr32 msxml3.dll /s regsvr32 msxml4.dll /s net start SwPrv net start VSS net start ProtectedStorage ...and per http://support.microsoft.com/kb/940184 I have deleted the key tree HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\EventSystem\{26c409cc-ae86-11d1-b616-00805fc79216}\Subscriptions I have also run chkdsk /F and chkdsk /R on both permanent hard disks. (I had a similar problem with another computer (same OS, same failure, same start point after SP1 install) but the problem went away when I forced Volume Shadow Copy Services to Automatic startup rather than Manual. I did not have to resort to following the Microsoft KB instructions.)

  Read the article

• Why I cannot copy install.wim from Windows 7 ISO to USB (in linux env)

  - by fastreload

  I need to make a USB bootable disk of Windows 7 ISO. My USB is formatted to NTFS, ISO is not corrupt. I can copy install.wim elsewhere but I cannot copy it to USB. I even tried rsync. rsync error sources/install.wim rsync: writefd_unbuffered failed to write 4 bytes to socket [sender]: Broken pipe (32) rsync: write failed on "/media/52E866F5450158A4/sources/install.wim": Input/output error (5) rsync error: error in file IO (code 11) at receiver.c(322) [receiver=3.0.8] Stat for windows.vim File: `X15-65732 (2)/sources/install.wim' Size: 2188587580 Blocks: 4274600 IO Block: 4096 regular file Device: 801h/2049d Inode: 671984 Links: 1 Access: (0664/-rw-rw-r--) Uid: ( 1000/ umur) Gid: ( 1000/ umur) Access: 2011-10-17 22:59:54.754619736 +0300 Modify: 2009-07-14 12:26:40.000000000 +0300 Change: 2011-10-17 22:55:47.327358410 +0300 fdisk -l Disk /dev/sdd: 8103 MB, 8103395328 bytes 196 heads, 32 sectors/track, 2523 cylinders, total 15826944 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdd1 * 32 15826943 7913456 7 HPFS/NTFS/exFAT hdparm -I /dev/sdd: SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ATA device, with non-removable media Model Number: UF?F?A????U]r???U u??tF?f?`~ Serial Number: ?@??~| Firmware Revision: ????V? Media Serial Num: $I?vnladip raititnot baelErrrol aoidgn Media Manufacturer: o eparitgns syetmiM Standards: Used: unknown (minor revision code 0x0c75) Supported: 12 8 6 Likely used: 12 Configuration: Logical max current cylinders 17218 0 heads 0 0 sectors/track 128 0 -- Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 0 MBytes device size with M = 1000*1000: 0 MBytes cache/buffer size = unknown Capabilities: IORDY(may be)(cannot be disabled) Queue depth: 11 Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 0 Current = ? Recommended acoustic management value: 254, current value: 62 DMA: not supported PIO: unknown * reserved 69[0] * reserved 69[1] * reserved 69[3] * reserved 69[4] * reserved 69[7] Security: Master password revision code = 60253 not supported not enabled not locked not frozen not expired: security count not supported: enhanced erase 71112min for SECURITY ERASE UNIT. 172min for ENHANCED SECURITY ERASE UNIT. Integrity word not set (found 0xaa55, expected 0x80a5)

  Read the article

• Display with intel integrated graphics, bitcoin mine with Radeon 6950

  - by karategeek6

  I'm on Ubuntu Linux 11.04 64 bit. I have an intel i5 with integrated graphics and a Radeon 6950, with one monitor. I would like to run my graphics on the integrated card, and run bitcoin mining on the 6950. I have bitcoin mining working when I use the 6950 for both display and mining. Every time I try and and use the integrated graphics instead, OpenCL doesn't recognize my 6950. Using aticonfig --initial when using the integrated graphics for display breaks things. So I used the xorg.conf it created as a basis and tried to manually edit it. I really don't know what I'm doing, though. My last attempt is given below. The graphics ran off the integrated card, but the 6950 wasn't recognized. Any help would be greatly appreciated! xorg.conf: #Section "ServerLayout" # Identifier "Intel Layout" # Screen "Default Screen" # Identifier "aticonfig Layout" # Screen "aticonfig-Screen[0]-0" # Screen 0 "aticonfig-Screen[0]-0" 0 0 #EndSection Section "Module" Load "glx" EndSection # Intel Section "Device" Identifier "Intel Integrated Graphics" Driver "intel" BusID "PCI:0:2:0" EndSection Section "Monitor" Identifier "Default Monitor" Option "VendorName" "Monitor Vendor" Option "ModelName" "Monitor Name" Option "DPMS" "true" EndSection Section "Screen" Identifier "Default Screen" Device "Intel Integrated Graphics" Monitor "Default Monitor" DefaultDepth 24 EndSection # ATI Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

  Read the article

• Multi-WAN bonding across different media

  - by Tom O'Connor

  I've recently been thinking again about a product that Viprinet provide, basically they've got a pair of routers, one that lives in a datacentre, Their VPN Multichannel Hub and the on-site hardware, their VPN multichannel routers They've also got a bunch of interface cards (like HWICs) for 3G, UMTS, Ethernet, ADSL and ISDN adapters. Their main spiel seems to be bonding across different media. It's something that I'd really like to use for a couple of projects, but their pricing is really quite extreme, the hub is about 1-2k, the routers are 2-6k, and the interface modules are 200-600 each. So, what I'd like to know is, is it possible with a couple of stock Cisco routers, 28xx or 18xx series, to do something similar, and basically connect a bunch of different WAN ports, but have it all presented neatly as one channel back to the internet, with seamless (or nearly) failover if one of the WAN interfaces should fail. Basically, If i got 3x 3G to ethernet modems, and each on a different network, I'd like to be able to loadbalance/bond across all of them, without having to pay Viprinet for the privilege. Does anyone know how I'd go about configuring something for myself, based around standard protocols (or vendor specific ones), but without actually having to buy the Viprinet hardware?

  Read the article

• Software/hardware to build video streaming server?

  - by Sasha Yanovets

  I am looking for a video streaming server solution, something like online TV server, with ability to make live broadcasts in the internet. What software could you recommend for that? What kind of hardware it should run on, should be there anything special? I am looking for a solution that could be scaled up to at least 1000 simultaneous users online with good resolution of video. I think it is good to have general answer on what direction to choose. But here more details on my specific case: I just looking for a solution almost from scratch. We have some video content that we've produced, but it is not delivered over internet yet. We do not tied to any particular vendor for now. We want to make 24 hours of steaming three 8 hour blocks with change of content every day. We want the ability to make regular live broadcasts. I guess we will need to have several options of streaming quality (low ~56 kb/s mid ~273 kb/s). Some terms just foreign to me (like play-truncation rate), if you could point out what parameters we should avare of, it would be great. Uplink to the internet is to be determined. We plan to start from something and scale up on the way. If you are already have some kind of media streaming server, just describe its configuration here (hardware, OS, software), peak number of concurrent users it serves. I think it could help people approaching this task.

  Read the article

• How to resolve virtual disk degraded in Windows Server 2012

  - by harrydev

  I am using the new Storage Spaces feature in Windows Server 2012. I have the following disks: FriendlyName CanPool OperationalStatus HealthStatus Usage Size ------------ ------- ----------------- ------------ ----- ---- PhysicalDisk2 False OK Healthy Auto-Select 2.73 TB PhysicalDisk3 False OK Healthy Auto-Select 2.73 TB PhysicalDisk4 False OK Healthy Auto-Select 2.73 TB PhysicalDisk5 False OK Healthy Auto-Select 2.73 TB There is also a separate OS disk. The above disks are part of a single storage pool: FriendlyName OperationalStatus HealthStatus IsPrimordial IsReadOnly ------------ ----------------- ------------ ------------ ---------- Pool OK Healthy False False Within this storage pool some virtual disks are defined, see below: FriendlyName ResiliencySettingNa OperationalStatus HealthStatus IsManualAttach Size me ------------ ------------------- ----------------- ------------ -------------- ---- Docs Mirror OK Healthy False 500 GB Data Mirror Degraded Warning False 500 GB Work Mirror Degraded Warning False 2 TB Now the virtual disks are all running normal 2-way mirror, but two of the virtual disks are degraded. This is probably because one of the physical disks was offline for a short period of time. However, now the virtual disk cannot be repaired, even though, all physical disks are healthy. There is plenty of available space in the storage pool. This I cannot understand so I was hoping for some help, on how to resolve this? Below I have listed the full output from the Get-VirtualDisk CmdLet for the "Work" disk: ObjectId : {XXXXXXXX} PassThroughClass : PassThroughIds : PassThroughNamespace : PassThroughServer : UniqueId : XXXXXXXX Access : Read/Write AllocatedSize : 412316860416 DetachedReason : None FootprintOnPool : 824633720832 FriendlyName : Work HealthStatus : Warning Interleave : 262144 IsDeduplicationEnabled : False IsEnclosureAware : False IsManualAttach : False IsSnapshot : False LogicalSectorSize : 512 Name : NameFormat : NumberOfAvailableCopies : 0 NumberOfColumns : 2 NumberOfDataCopies : 2 OperationalStatus : Degraded OtherOperationalStatusDescription : OtherUsageDescription : Disk for data being worked on (not backed up) ParityLayout : PhysicalDiskRedundancy : 1 PhysicalSectorSize : 4096 ProvisioningType : Thin RequestNoSinglePointOfFailure : True ResiliencySettingName : Mirror Size : 2199023255552 UniqueIdFormat : Vendor Specific UniqueIdFormatDescription : Usage : Other PSComputerName :

  Read the article

• Windows 7 - Intermittently processes will not close when the app closes

  - by Bill Sambrone

  I have a user I am supporting who has the strangest issue. There are 2 problem applications, Word 2010 and a scanning program called ScandallPro. Intermittently (and at least once a day), she will close an app and the underlying process will not close. Both Word 2010 and this scanning software have all the latest updates. There is another user who has the same software that does not have this problem, and has identical hardware. I have formatted and rebuilt the computer for the user who is having the problems. After the rebuild, the machine was fine for a day but the scanning software continues to intermittently keep the process running even after it is closed. This is a problem because she cannot open a new instance of it while the process is still running. There is a boatload of line of business software on this machine, all of which she needs. I believe the Word 2010 issue is due to a misbehaving add-in (there are 2 add-ins, neither of which seem stable), and I think my best bet is to work with the add-in vendor on it. The scanning program staying open is isolated to this 1 user. The only difference between her machine and the other user is that she has Quickbooks, RoboForm, and Adobe Acrobat X Pro. Any ideas of what can be causing this, or other diagnostic steps to try?

  Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >