Search Results

Search found 2066 results on 83 pages for 'cable'.

Page 6/83 | < Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >

  • IP Micro-outages, telephone micro-outages, and CATV micro-outages

    - by Michael Graff
    This is a long and complicated question, mostly because it has been going on for 2.5 years without a solution in sight. It also is only one-third computer related, the other two-thirds are cable TV and cable-phone related. Background I have COX Communications for a cable provider, and we get Internet, digital cable TV, and digital phone service through them. The Internet is a SB5101 right now, and has been a DPC2100 and SB5120 in the past. Same results. The phone service is provided through a telephone interface mounted on the outside of the house (not classic VoIP) and the CATV is through a Scientific Atlanta receiver without DVR. I do have a TiVo connected to the CATV box. Symptoms The CATV shows "blocking" -- sometimes very very short duration where a few blocks appear on the screen. Sometimes it lasts long enough that the video "pauses" for 2-5 seconds, and rarely but not unseen the audio also fails. The CATV decoder box shows no correctable (FEC) or uncorrectable errors. That is, all BER counters are zero for the video stream. The Internet shows "micro-outages" where it appears that sent packets are not making it out, but I continue to receive packets from local modems. That is, pings stop coming back, but I continue to see modems broadcast for DHCP, and sometimes they ask more than once. The cable modem shows no errors during this time, but cable modems lie like you would not believe. It is actually possible to unplug the coax from the modem for 20 seconds and it reports NO ERRORS to the provider's tools. The phone service cuts out for 1-3 seconds, infrequently. When this happens, I hear NOTHING (not even comfort noise) and the remote side hears a "click" as if I were getting a call waiting message. However, there is no call incoming, other than the one I'm currently on of course. Things SEEM to happen more frequently when the temperature outside swings from cold to warm, so fall/spring seems worse than summer/winter. All micro-outages occur between once or twice a day (which I could ignore) to 10 times per hour. All SNR, signal levels, noise levels, etc. show very close to optimal when measured. COX's diagnosis This is a continual pain for me. Over the last 2.5 years, they have opened, "fixed" something, and closed the tickets. They close it without confirming that it is indeed better, and when I reopen they cannot do that, but instead they open a new ticket and send yet another low-level tech out to do the same signal tests and report that all is OK. I've finally gotten a line tech who has a clue and is motivated enough to pursue this with me. We have tried things like switching the local nodes over to UPS and generator power, but this does not trigger the noise. We have tried replacing all cabling, the tap outside my house, the modem, the CATV decoder -- all without resolution. Recently they have decided it is both my computer or switch, my TiVo, and my phone that are all broken and causing this issue. My debugging steps I spent the worse day of my TV-watching life yesterday and part of today. I watched live TV without the TiVo. I witnessed blocking, but it did "feel different." and was actually more severe. Some days it is better, some days it is worse, so perhaps this was just a very bad day. Today, I connected the TiVo to my DVD player, and ran two very long movies through it. I saw no blocking at all during nearly 6 hours of video. Suggestions? Does anyone have any suggestions on what to do next? I understand perhaps only the IP side can be addressed here, but it is one of the more limiting debugging options.

    Read the article

  • USB Serial cable with CDC support

    - by Harsha
    Hi All, I bought a USB to Serial cable which claims to be CDC compliant. But the bInterfaceClass value in interface descriptor is 0xFF(which is vendor specific). I was expecting it to be 0x02 (Communications and CDC control). In the device manager, i found that the drivers being loaded are ser2pl.sys and serenum.sys. I had learnt usbser.sys is the windows CDC driver, but it was not loaded for my cable. I am pretty much new to this CDC, so i have following questions 1.Does this indicate that the cable is not CDC compliant 2.Can i make this cable CDC compliant (since CDC is a driver functionality), by loading usbser.sys. If yes how?

    Read the article

  • How to connect to a Virtualbox guest from the host when network cable unplugged

    - by Greg K
    I'd like to work offline (I'm flying to the US twice this month), to do this I need access to a linux development server. When I work from home I boot a VirtualBox VM and that acts as my dev server for the day (providing Apache, PHP & MySQL to run my server side code). However, I'd like to work with my VM when I'm not connected to a network. I have my Ubuntu VM guest set up with a bridge connection so it can serve HTTP and provide SSH access from inside my local network. I've tried to manually configure my network settings on both Mac OSX (the host) and Ubuntu (the guest) but I can't even ping my own NIC address (127.0.0.1 can, 192.168.21.x I can't) in OS X when I unplug the cable. Manual network settings: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx inet 192.168.21.5 netmask 0xffffff00 broadcast 192.168.21.255 media: autoselect (100baseTX <full-duplex,flow-control>) status: active I can ping localhost fine, as well as my VM (.20) and SSH too. $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes 64 bytes from 192.168.21.5: icmp_seq=0 ttl=64 time=0.085 ms 64 bytes from 192.168.21.5: icmp_seq=1 ttl=64 time=0.102 ms 64 bytes from 192.168.21.5: icmp_seq=2 ttl=64 time=0.100 ms 64 bytes from 192.168.21.5: icmp_seq=3 ttl=64 time=0.094 ms $ ping 192.168.21.20 PING 192.168.21.20 (192.168.21.20): 56 data bytes 64 bytes from 192.168.21.20: icmp_seq=0 ttl=64 time=0.910 ms 64 bytes from 192.168.21.20: icmp_seq=1 ttl=64 time=1.181 ms 64 bytes from 192.168.21.20: icmp_seq=2 ttl=64 time=1.159 ms 64 bytes from 192.168.21.20: icmp_seq=3 ttl=64 time=1.320 ms Network cable unplugged: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx media: autoselect status: inactive $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes ping: sendto: No route to host ping: sendto: No route to host Request timeout for icmp_seq 0 ping: sendto: No route to host Request timeout for icmp_seq 1 Does OS X disable the NIC when the network cable is unplugged? Any way to stop it doing this?

    Read the article

  • File sharing from a cable connected pc to wifi connected laptop (windows 7 ultimate)

    - by Aiden Jones
    I have a one desktop running windows 7 ultimate connected to Ethernet cable. And I want to share folder to another wifi connected laptop (also windows 7 ultimate). Both machines are on the same home internet connection. I have tried to share folders by going to properties sharing advanced sharing permissions checked all the boxes to allow all but I don’t see any shared files on my laptop. I know it’s possible to share folders between two Wi-Fi connected machines but how can it be done when one pc is cable connected and other is Wi-Fi connected on the same internet connection.

    Read the article

  • Limited RGB range due to HDMI cable?

    - by Cedric Reichenbach
    I have a NVidia GeForce GTX 660, connected to a Samsung SyncMaster S24B350 through a HDMI cable. On my computer, I'm running both, Windows 8 and Linux Mint. I think that something might prevent my system from using the whole RGB spectrum, since bright colors seem to vanish into white under standard settings. However, under Linux I could switch to a limited color range mode (16-235) and suddenly, the image looked much better. Is it possible that the HDMI cable limits color range (since it was originally inteded for TVs)? Is there a way of switching to limited color range mode in Windows 8 as well?

    Read the article

  • Why didn't cable select work?

    - by jldugger
    I got roped into doing tech support for a friend of the family. Obviously I'd already failed to hide my powers, ala Penny Arcade. Anyways, the guy bought a DVD burner OEM from Microcenter, and asked me to install it. So I stopped by before and thought I'd be slick and use Cable Select on the jumpers. I didn't get a chance to test it before it I had to leave, and it seems that this didn't work. I came back this week to investigate, and he explains he's confused how none of the software he downloaded was able to burn. So on a whim I switch it to explicit master / slave, and it starts working fine. Whoops. Well, at least it's not the extra crap he found and downloaded for free from the internet. Why doesn't setting both jumpers to Cable Select solve this?

    Read the article

  • Loss of wireless network connectivity when playing video via HDMI cable

    - by Jeff Fohl
    Hi Folks - New to Super User, so I hope this question fits in with the guidelines. Very strange problem I am having, and I am at a loss as to how to continue troubleshooting this one. The basic problem is that when I attempt to watch streamed video on a particular display device (an Optoma HD180 projector), my network connectivity drops like a stone to barely measurable levels. This is my setup: I have a Dell H2C 730x running Windows 7 64bit. This particular computer has two ATI Radeon HD 4800 video cards. I have two Samsung 22" monitors connected to one card, and an Optoma HD180 digital projector connected to the other card via an HDMI cable. My internet connection is normally a reliable 6Mbps. The problem I am having occurs when I stream video (or even just browse the web) on the Optoma Projector. When I do this, my internet connection drops to practically zero (just a few kilobits per second). When I move the browser away from the projector, and over to one of my Samsung monitors, the internet connection comes right back. Note that the Optoma projector is on and enabled as a third monitor all this time. I can move the mouse around on the projector without triggering the problem. I tried pinging my router when I was playing a movie on one of the monitors, and I get a 1 millisecond response. However, when I have the movie playing on the Optoma projecter, pinging the router gives me response times in the hundreds of milliseconds, or times out completely. So, it clearly is something local to my machine - and not some sort of throttling occurring down the line. I would think that it is possibly something to do with the HDMI driver conflicting somehow with my network driver (which is a USB-based wireless connection). This one has me really stumped. Anyone have any ideas? EDIT: I am now leaning towards the possibility that the HDMI cable is somehow interfering with the wireless network, when large amounts of data are being pushed through the cable. Is this possible?

    Read the article

  • Un-balanced network speed although using fiberoptic cable line

    - by Hoàng Long
    I'm not sure this is a right place to ask this question, but there's a strange thing that I don't quite sure what the reason is. My company has hired a fiberoptic cable line for network use (Wifi and cable through a router). But the strange thing is that, whenever someone view YouTube or listen stream music, then network speed for all the others become extremely slow. The download speed for that person is about 4-5 MB/s (or more), but others suffer. I'm still a newbie about networking. But I know there should be a solution. Could anyone tell me a way to stop this bad behavior? It's not possible for asking people not viewing YouTube, since that's part of their jobs. Any insights about this problem would be very welcome.

    Read the article

  • No sigal showing on LCD TV when Conects Leptop via VGA Cable [migrated]

    - by Amit Prajapati
    I am trying to connect my laptop to Samsung LCD TV by VGA TO HDMI cable My Laptop find Samsung tv on display setting. But When I press fn+F7 key my TV display No Signal My laptop specifications are: "Lenovo R61 ThinkPad, Model: 8935AE7 Window7 Ultimate 32 bits 2GB RAM VGA Port available No HDMI Port My TV specification are: Samsung LCD 26 HDMI Port available VGA Port Available I want to know what is problem? When I connect Another Dell Laptop (Window7 32 bit) with HDMI to HDMI cable it work properly. Thanks in Advance!

    Read the article

  • Identifying a CAT6 cable in a bundle

    - by Jon Tackabury
    We had a contractor wire up our office with all the cables leading back to a central location. The only problem is that he didn't label anything, so we have no idea which cables go to which room. One end of the cable is terminated in a wall-jack (in the rooms), the other end is un-terminated and will be punched to a patch panel. Is there a way to identify the cables without having to terminate them? We'd like to group the cables on the patch panel by room, but I don't want to crimp/punch each cable twice. Thanks!

    Read the article

  • new PC not work with existing router, but works fine when directly connecting to cable modem

    - by user34786
    I bought a new desktop PC (eMachine ET1331G-03W from WalMart) with windows 7 installed, but I can not access internet by connecting to my existing wireless router(LinkSys BEFW11S4) with wired cable. Though all other existing desktops and laptops have no problem connecting to the same router. However, the new desktop PC works fine and able to connect to internet if I bypass the router and directly hook up with the cable modem. At new PC when connecting to the router, I got the below information by typing ipconfig, the IP address looks wrong to me: autoconfiguration IPv4 Address: 169.254.71.140 subnet mask: 255.255.0.0 default gateway: (empty) NetBIOS over Tcpip: Enabled Typing ipconfig at all other desktop and laptop have values like below, which are good to me: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.1.140 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 The wireless router was on 192.168.1.1, I do not know why the new desktop got 169.254.71.140 IP? It should have something like 192.168.1.xxx, and it was configured to automatically get IP by DHCP. I have tried to switch cables,power off cable modem, router and reboot new pc many times and got no luck. So I believe this is only an issue related to router or new pc configuration. Can someone help me figure out the issue?

    Read the article

  • Can't connect to Internet through WiFi, but can with cable

    - by aldy505
    I'm using Windows 7 32-bit, Toshiba Portege laptop. I want to connect to the WiFi, usually I can do that easily. But, I don't know.. maybe when I tried to install a Microsoft Research: Mesh Virtual WiFi that could connect more than 2 wireless networks. I wanna try in connecting both Wireless router and my personal Ad-Hoc. Now, my laptop don't recognize my WiFi, well, I can connect to the WiFi but it says: "Limited access" and doesn't really connect to the internet. But when I plug the LAN cable, it works. I know the problem is in the laptop's wireless connection or in the properties. Any help for this? UPDATE: The IP and DNS settings, I set to automatic, and when I ran diagnostic, Windows tells me that the wireless network adapter is the problem, but they told me to insert the LAN cable, so how to fix the wireless? They didn't tell me how to fix that.

    Read the article

  • Laptop display not working unless DVI cable is plugged in

    - by marien
    I have a Lenovo ThinkPad T420 with an i5 processor and integrated graphics. I dropped the laptop and now the screen is not working. I replaced the screen and it is still not working. It shows the BIOS and then at Windows login the screen gets all static looking. But if I plug in a DVI-to-HDMI cable the laptop starts and works fine. Even the external display works and the laptop display works too. As soon as I unplug the cable the screen crashes and is all static. I cannot figure out the problem. The video works because the external screen still works. How can I fix this?

    Read the article

  • Issues connecting to a pix 501 via console cable

    - by Bourne
    Have a pix 501 that was set up to do filtering and I was working on setting the vpn up when I lost ssh connectivity. Looking at the front, all 4 lan lights blink intensely green but in a very repetitive pattern. The funny thing is there are only 3 devices connected to the 4 ports so that's the first element that doesn't look right to me. Console cable light doesn't turn on when cable is plugged in and have tried rebooting it many many times to see the bootup sequence with no result. Also, I cannot connect to it via pdm or console but the traffic is permitted through. Are there any additional troubleshooting steps I could do or should I count it as dead? Thank you.

    Read the article

  • No sigal showing on LCD TV when Conects Leptop via VGA Cable

    - by Amit Prajapati
    I am trying to connect my laptop to Samsung LCD TV by VGA TO HDMI cable My Laptop find Samsung tv on display setting. But When I press fn+F7 key my TV display No Signal My laptop specifications are: "Lenovo R61 ThinkPad, Model: 8935AE7 Window7 Ultimate 32 bits 2GB RAM VGA Port available No HDMI Port My TV specification are: Samsung LCD 26 HDMI Port available VGA Port Available I want to know what is problem? When I connect Another Dell Laptop (Window7 32 bit) with HDMI to HDMI cable it work properly. Thanks in Advance!

    Read the article

  • What cable would be used for a touch screen

    - by George Bailey
    I was told that any monitor could be turned into a touch screen if you have the right software. This has got to be old news, or even a myth. Please shed some light on this if you can. Am I wrong? My primary question is which cable would normally be used to hook up a touch screen. Would you need 2 cables for this (one for the monitor, one to receive touch events?), or is a single cable going to have data in both directions (perhaps an HDMI?)

    Read the article

  • Samsung S23A750D 23" 120Hz get no signal

    - by John Carter
    I have a few days ago received this monitor. Samsung S23A750D 23" 120Hz I am using it with a Gainward Nvidia GTX570 Phantom GPU via DisplayPort cabling. The trouble I am having is that the monitor has great trouble picking up a signal from the GPU when the computer has gone into sleep mode or been switched off (at this point I can get a signal to the monitor). It's only when I turn the computer back on and then the monitor that I get no signal. To get a signal I have to remove the power cable and put back in or sometimes remove the DP cable and put back in. I have tried not turning the monitor off (the monitor goes into a sleep mode when the computer goes into sleep mode) but on putting the computer on it does not pick up a signal. It is only by removing the power cable and/or DisplayPort cable will I get a signal. And this is intermittent. I have tried upgrading the firmware from Samsung but this hasn't helped. Any ideas?

    Read the article

  • Running computer from separate room

    - by Dan
    I want my computer to be in the basement, but to use it on the first floor. Which cables should I run through the floor? Can some be wireless or other methods? Here are some of the options I've thought of: Basic: Run DVI, usb (mouse), usb (keyboard), and audio cable (4 cables) USB Hub option: Run DVI, and 1 usb, then using a usb hub split it into mouse, keyboard, maybe even audio (2-3 cables) HDMI Option: If I get a new video card and monitor that supports HDMI, would I be able to run both audio and video through it? Would the monitor have to have an audio out? Also there is a lot of extra bandwidth in the HDMI cables, could I send two monitors on 1 cable or would I have to use 2 cables? How about sending mouse/keyboard through the HDMI cable? I see a lot of monitors with USB hubs built in, but I assume I'd still have to wire HDMI + 1 USB cable to use the USB hubs? X Terminal Machine/Thin Client: I don't really know much about this option. Not sure if it would allow me to run graphics acceleration and watch movies, does anyone know more details about what this would allow me to do? Other options: Any other ways to do this? Can any of this be wireless?

    Read the article

  • What am I doing wrong with this cat 6 patch panel wiring?

    - by Max Hodges
    top number is transmitter bottom number is remote terminator 12345678 36145278 is this because I could be mixing T568A and T568B wiring? how do I know if my patch cord is A or B? Do I just look at the plug and match it up with the diagram on the back of the panel somehow? EDIT I read that 36145278 indicates a cross over cable, but I'm not trying to make a cross over. Where did I go wrong? I'm guessing the cable plug is T568A but I wired it to the panel using T568B. So I need to redo it as T568A. But in the future how do I know if I cable is A or B? Cheers!

    Read the article

  • ethernet not working

    - by good boy
    i wanted to know how do i setup an ethernet connection on a laptop,my isp gave me a telephone like cable which fits the ethernet port. i guess its the ethernet cable. when i connect it, nothing happens on the pc the ethernet card(realtek pcie gbe family controller) says cable not plugged in. i am using wired connection for first time.the system is completely stable with softwares .the drivers are also automatically updated through a manufacturer installed update system. the isp says there must be some sort of light on the port. whats the problem? how do get it working.

    Read the article

  • Difficulty racking HP ProLiant Gen8 servers

    - by Systemspoet
    We're an all Proliant shop with around 50 servers, mostly DL360s and DL380, from G5's through G7's. We just got our first two G8's in and went to rack them. We were stunned to find out that the new cable management arms protrude almost 1 inch deeper into the rack then previous iterations of the Proliant line. Unfortunately that causes them to occupy the same space as the PDU's in our APC racks. In a non-densely populated section of rack that's no biggie, but in a densely populated section it's impossible to get the cable arm into place without dislodging another machine's power. Has anyone else run into this? Obviously racking machines without cable management arms is not an option. I supposed we could reconfigure our racks but that's a nightmare.

    Read the article

  • Difficulty racking Proliant G8's

    - by Systemspoet
    We're an all Proliant shop with around 50 servers, mostly DL360s and DL380, from G5's through G7's. We just got our first two G8's in and went to rack them. We were stunned to find out that the new cable management arms protrude almost 1 inch deeper into the rack then previous iterations of the Proliant line. Unfortunately that causes them to occupy the same space as the PDU's in our APC racks. In a non-densely populated section of rack that's no biggie, but in a densely populated section it's impossible to get the cable arm into place without dislodging another machine's power. Has anyone else run into this? Obviously racking machines without cable management arms is not an option. I supposed we could reconfigure our racks but that's a nightmare.

    Read the article

  • Ubuntu/Nvidia lists DVI dual cable as single

    - by Joseph Mastey
    I have an NVidia Quadro FX 880M graphics card, from which I am trying to drive 2 monitors: my internal laptop montior (15.6", 1920x1080, Nvidia driver says it's running via DisplayPort) and an external 27" monitor (Dell U2711, 2560x1440 native resolution, via DVI). I've hooked the dual DVI cable to the dual DVI port on my dock (Dell PR03X) and installed the proprietary NVidia driver, but I cannot seem to get the full 2560x1440 out of the larger 27" external monitor. Looking at the NVidia driver settings, the monitor's connection is reported as a single DVI cable, rather than a dual one, which would explain the reduced resolution. Does anyone have any experience with an issue like this? What can I do to make full use of my new monitor? (Possibly) Relevant Information: There is no DVI port on the laptop itself, but one is provided via the dock. The laptop and dock both provide a DisplayPort jack, but I have been unable to get this working on either w/ the monitor. I did have the nouveau driver installed when I installed the nvidia proprietary driver, but have since removed it (no change in the monitor situation when I removed it). The 27" reports a max resolution of 1680x1050. Thanks, Joe

    Read the article

  • Does water damage a fiber optic / cat5 cable

    - by chris
    One of the buildings I support recently had an adventure with a broken fire sprinkler. Lots of water everywhere. One of the "drains" the water used was the vertical risers between network closets. The cable plant in this building has bundles of cat5e as well as conduit with bundles of multimode fiber optic cables. The fiber is standard multi strand plenum rated stuff that terminates in boxes that have the patches to the switches. As far as I can tell, no water got near the ends of the cables (fiber or copper) but the conduit was saturated, and is likely still saturated because there isn't any air flow to dry the cables out. My gut reaction is that while it didn't do the cables any favors, it likely also isn't going to cause any problems. A little more reading / googling around leads me to believe that the water may cause problems down the road. Some pretty pictures so everyone knows what I'm talking about: Fiber conduit: Vertical riser, going down: Vertical riser, going up: Does anyone have any experience with this sort of damage and how to deal with it? Should we just ask the insurance adjuster to add "pull new structured cable" to the list of things to be replaced? And, if the opinion is "replace it because it'll start failing randomly over time" please include links that describe the specific failure modes, so I've got some ammo to use with the adjuster.

    Read the article

< Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >