Search Results

Search found 2504 results on 101 pages for 'hp envy'.

Page 6/101 | < Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13 | Next Page >

HP Pavillion DV6500 recovery disk failure

- by Scott W

I recently attempted to re-install Windows Vista on an HP Pavillion DV6500 using the factory recovery DVD's, but encountered a strange problem. When the recovery disk attempted to reformat the hard disk, it failed at 22%. The error message provided was not very informative, just the error code "0x400110020000 1005". A google search turned up some people with a similar problem who asserted that HP has been know to ship corrupted recovery DVDs. The recovery disk did manage to reformat the the recovery partition before failing though, so recovering from the partition is no longer an option. It would be possible to reinstall from an off-the-shelf retail copy of Vista and then pull the drivers from HP's website, but I don't have access to a copy of Vista, and it would really be outrageous to have to purchase a new OS when I have a perfectly valid license already. Thought about biting the bullet and upgrading to Windows 7, but my understanding is that without Vista installed I'd be unable to use the upgrade version, and be forced to purchase the more expensive non-upgrade retail copy (!). Can anyone suggest a possible solution to this Catch-22? I've run out of ideas.

Read the article
hp proliant dl360 disk diagnostic issue

- by user1039384

We recently got two used drives (15000) and installed on our HP proliant dl360 G5 server. Created RAID1 and used HP SmartStart CD to perform diagnostics. Interestingly, the Diagnostic tab immidiately fails on Logical drive testing saying the Disk1 should be replaced, while the Test tab successfully runs all the complete tests on both disks and does not find any issue. At the meantime, when booting to esxi 5, vSphere periodically shows the Disk1 as Unknown and Logical drive in recovery process. This happens every 5-10 minutes. Here is the log from HP SmartScan diagnostic: 1 - Device, Test: Logical Drive 1, Storage Controller in Slot 0 1 - Description: The controller has reported a critical error in the drive error log. 1 - Recommended Repair: This drive should be replaced. 1 - Failed Count: 44 1 - Error code: F157 There is also another error log record (see below): 2 - Device, Test: test_components/libstorage.so ID 2 - Description: An unexpected exception occurred while performing an operation. Exception message: CISS_StatusHandler::evaluate: commandStatus = 4 (INVALID); hexdump of CISS_ErrorInfo: 00000000: __ __ 04 __ 20 __ __ __ __ __ __ __ __ __ __ __ .... ... ........ 00000010: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ 00000020: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ Device: Hard Drive 2, Storage Controller in Slot 0 Property name: Bad Target Count 2 - Recommended Repair: Reboot or restart Insight Diagnostics. Retry the test. If the problem persists, upgrade to the latest version of Insight Diagnostics. 2 - Failed Count: 48 2 - Error Code: F62 Note that rebooting didn't help and I was running the latest diagnostic software version. Anyone has a clue? Is this a real disk issue? BTW, the controller is Smart Array E200i Thanks in advance

Read the article
HP DL185 - very slow disk read speed

- by fistameeny

Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

Read the article
HP Pavillion DV6500 recovery disk failure

- by Scott W

I recently attempted to re-install Windows Vista on an HP Pavillion DV6500 using the factory recovery DVD's, but encountered a strange problem. When the recovery disk attempted to reformat the hard disk, it failed at 22%. The error message provided was not very informative, just the error code "0x400110020000 1005". A google search turned up some people with a similar problem who asserted that HP has been know to ship corrupted recovery DVDs. The recovery disk did manage to reformat the the recovery partition before failing though, so recovering from the partition is no longer an option. It would be possible to reinstall from an off-the-shelf retail copy of Vista and then pull the drivers from HP's website, but I don't have access to a copy of Vista, and it would really be outrageous to have to purchase a new OS when I have a perfectly valid license already. Thought about biting the bullet and upgrading to Windows 7, but my understanding is that without Vista installed I'd be unable to use the upgrade version, and be forced to purchase the more expensive non-upgrade retail copy (!). Can anyone suggest a possible solution to this Catch-22? I've run out of ideas.

Read the article
HP LaserJet 1515: Disable "refill" warning

- by Pekka

I have a HP LaserJet 1515 connected to a Windows 7 PC. The Magenta cartridge is empty; the printer shows a warning to that effect, and won't let me print even black-and-white documents any more. I can't turn the warning off manually using the printer's small console: When I try to enter any menu, the display says "Menu access disabled". I have no idea why. There is a setting to override the warning, but it can't be changed using the Network interface in the browser (Although it is there on the status page) According to the manual,the HP printing tool is supposed to offer a switch for this, but it won't install on my Windows 7. It just rumbles about for half an hour, to magnificently exit with an "unknown error" requiring a reboot. On second look, the problem seems to be that Windows 7 just isn't supported. There is no download link for the tool when you specify Windows 7 as your OS. I just want to print a black-and-white-document on a printer whose black cartridge is still 65% full. Is this indeed impossible? On second thought, I'm cross-posting this on the HP support forum. I'll update here if anything comes up.

Read the article
Ubuntu 12.4.1 failing in vm both Vbox and Vmware on new HP Envy 4t-1000

- by Chas

Brand new to Linux, getting frustrated trying to get an environment up with Ubuntu. My primary goal is to learn Linux and Apache/PHP development. I need to keep my Windows OS as main on my machine for work, so i'm trying to virtualize Ubuntu 12.4.1 without luck (many attempts). I have a new HP Envy 4t-1000 with 16gb ram, and 32 gb ssd caching with 500gb spindle hard drive. Graphics card is an Intel HD 3000 with AMD Radeon 7670M. With installing Ubuntu desktop in VBox, I'm getting this result: https://forums.virtualbox.org/viewtopic.php?f=6&t=51939 With VMware workstation 7 (patched), I complete the install of Ubuntu, it reboots, purple desktop briefly flashes then it drops to command line. I bought a beginning Ubuntu book, and it recommends trying to manually configure graphics if this happens. So I tried doing a safe boot holding shift - I get to the first screen (GRUB) loads fine, and I choose recovery mode. After choosing the recovery mode, I get the recovery mode options, and can arrow down to what the book suggests 'Run in fail safe graphic mode.' Once I select this option, I get a black screen with a large white dialogue box, at the top it says "The system is running in low-graphics mode. Your screen, graphics card, and input device settings could not be detected correctly. You will need to configure these yourself." Then there is an ok button way down at the bottom. When I select 'ok' I get a menu for a few options, book recommended 'reconfigure graphics.' When I try this, I get a menu of two options: 1) "Use generic (default) configuration or 2) use backup. I've tried both options several times, hitting ok just refreshes screen and nothing more. Rebooting at this point just goes back to command line as before. I don't know what to do at this point, I've spent too many hours this weekend trying in both VBox and VMware to get Ubuntu going. Isn't there like a very basic graphic display or something I can use to at least get into the desktop? I explored the GRUB some more, and tried to look at the startup and xserver logs - both are blank. No help there I guess? When I try to choose 'Edit the configuration file, then 'ok' screen just refreshes on same menu options, nothing happens. thx for any advice. I really need to focus on learning Linux, Apache and PHP, so perhaps Ubuntu just won't work on my hardware? Any other suggestions? I will need to virtualize - THANKS for any help/advice.

Read the article
hp ProLiant DL380 G6 server error code: 347 of array controller

- by alhaythum

I have got a bran new hp ProLiant DL380 G6 server with embedded smart array P410i controller, I got 164 GB SATA drives and wanted to change them with 300 GB SATA drives before installation. Now, we replace the drives and begin the configuration with the hp DVD and begin; when we reach the point that we want to save the configurations, an error message appears: "The operation has failed with an unknown error, please restart the application and attempt the operation again" When using Rescan System, this error message appears: "Status Alerts - Smart Array P410i in Embedded Slot Warning Status Message Code Description 347 The cache for Smart Array P410i Embedded Slot is not configured" We return back to the 164 GB SATA drives and the message just keeps appearing again. Any help please.

Read the article
How HP D2700 disk enclosure is monitored for alarms via SNMP

- by VSAC

We have HP D2700 disk enclosure and we would like to monitor D2700 (connected to HP Proliant DL360G8) for alarms.I have following questions regarding this. What are the options available for reporting D2700 hardware alarms (disk failure, power failure) via SNMP? We understand the D2700 to have an Ethernet interface for controller A and B and alarms are available via SNMP via this interface. Can anyone provide the actual alarms via this interface? (MIB and alarm list) As we have a number of D2700’s and would like to minimize the number of physical connections to the switch and associated IP addresses; Is there a mechanism to monitor the D2700 from the SCSI connected HPDL360 and raise SNMP alarms from the DL360 for hardware failures on the D2700? If so can anyone provide details and the actual alarms and MIB via this mechanism? Thanks!

Read the article
HP Blade ILO not responding in chassis ILO

- by bobinabottle

I have just started at a new company and I am inspecting their current server config. The HP 480c blades in a c7000 chassis aren't responding to ILO, although the chassis ILO is working fine. I have a feeling the last sysadmin configured the blades ILO as static IPs and it is not responding correctly. The servers are sitting in a datacenter and I'm hoping to be able to fix this remotely. Is there a way that I can change the ILO static IPs for the blades remotely? If not and I do have to go onsite, how do I change the IP addresses of the ILO for the blades? (Sorry I'm not very familiar with HP servers) thanks for you help!

Read the article
Creating a dynamic lacp trunk from HP Procurve 2412zl to Proliant DL380 G7

- by Maalobs

I'm configuring an IEEE 802.3ad (LACP) dynamic trunk from a HP Procurve 2412zl (firmware version K.15.07) switch to a HP Proliant DL380 G7 server. The DL380 has 4 NICs and is running Win2008 R2, so I'm teaming the NICs together and leaving everything on the recommended "automatic" setting in the HP NIC configuration tool. The server is one of two, they'll be connected on interfaces F17-F20 and F21-F24 respectively on the switch. I need the servers in a separate VLAN, here is the configuration for the VLAN: vlan 10 name "Lab_Mgmt" untagged B2,F17-F24 ip address 172.22.71.3 255.255.255.0 tagged B21 exit There is a DHCP-relay into the VLAN 10 from another device beyond interface B21. The Advanced Traffic Management Guide says that in order to run a dynamic LACP trunk on another VLAN besides the DEFAULT_VLAN, you need to first enable GVRP and then use "forbid" to stop the interfaces from automatically joining DEFAULT_VLAN when the dynamic trunk is created. GVRP brings some other stuff with it that I don't want or need, so I disable it with "unknown-vlans disable" on all other interfaces. Here is how I do it: procurve-5412zl-1(config)# gvrp procurve-5412zl-1(config)# interface A1-A24,B1-B24,C1-C24,D1-D10,D13-D24,E1-E24, F1-F16,K1,K2 unknown-vlans disable procurve-5412zl-1(config)# vlan 1 forbid F17-F24 procurve-5412zl-1(config)# interface F17-F20 lacp active The result afterwards looks all successful: procurve-5412zl-1(config)# show trunks Load Balancing Method: L3-based (Default), L2-based if non-IP traffic Port | Name Type | Group Type ---- + -------------------------------- --------- + ------ -------- F17 | XYZTEAM3_NIC1 100/1000T | Dyn2 LACP F18 | XYZTEAM3_NIC2 100/1000T | Dyn2 LACP F19 | XYZTEAM3_NIC3 100/1000T | Dyn2 LACP F20 | XYZTEAM3_NIC4 100/1000T | Dyn2 LACP procurve-5412zl-1(config)# vlan 10 procurve-5412zl-1(vlan-10)# show lacp LACP LACP Trunk Port LACP Admin Oper Port Enabled Group Status Partner Status Key Key ---- ------- ------- ------- ------- ------- ------ ------ F17 Active Dyn2 Up Yes Success 0 0 F18 Active Dyn2 Up Yes Success 0 0 F19 Active Dyn2 Up Yes Success 0 0 F20 Active Dyn2 Up Yes Success 0 0 On the Proliant server, the NIC configuration Tool is also indicating that a 802.3ad dynamic trunk has been established. Everything should be good, but it isn't. The server is not getting an IP-address from the DHCP, which it does if I'm not enabling LACP. If I configure the server to a static IP-address on the VLAN 10 subnet, it can't even ping the switch IP-address, much less anything outside of the VLAN. The switch can't ping the server either. I did another attempt with F17-F20 tagged, and checking the box "Default Native Tag (VLAN 10)" in the NIC configuration tool on the server, but there was no difference. Does anyone have any idea what I might have missed?

Read the article
Network Scanning: HP Laserjet 2840 & Windows 7 (+ Linux?)

- by Eddie Parker

I own a HP Laserjet 2840 multifunction printer. It's a fabulous device, but on Windows 7 it can't network scan. HP doesn't seem to support it in anything greater than Vista, and they aren't forth coming with solutions. I'm curious if anyone else has gotten work arounds to this problem. One possible avenue for me is that I have an always-on Gentoo server that is configured to see the printer as a fax and printer using hplip. I have this shared via samba and I can print just fine through samba. Is there a similar way I can do network scanning? Anyone know of where I start looking for this?

Read the article
How do I install an HP home-use printer on Windows Home Server (Windows Server 2003)

- by Rob Allen

I have an HP DeskJet F4210 printer that I would like to share on my network via Windows Home Server. Unfortunately, the driver installation checks for supported OS's, detects Home Server as Windows Server 2003 and exits. The driver install supports WinXP, W2k, Vista, and Win98SE. In theory, drivers for XP or Windows 2000 should work fine with Home Server. When using the "Install Printer" tool in Home Server I am only able to select .inf files (there are serveral on the install media) but the driver folders for XP and 2000 have .sys and .dll files. How can I bypass HP's short-sighted install program and get this printer up and running on Home server? I'll be happy with basic print functionality and will save the task of enabling scanning for another time.

Read the article
HP Pavilion dv3 volume control display driver on Windows 7

- by Farinha

I've recently bought an HP Pavilion dv3-2150ep and I'm having a hard time getting the volume control display to work as expected. The control is a back-lit touch-sensitive bar above the keyboard. Now the buttons to turn the volume up and down actually do it, but the lightning is not changing at all. The mute button does change color when toggled. I'm not sure if I'm missing any drivers here (I've installed all of those on the HP support page that seem to have something to do with sound and/or display) or if I have to activate this somewhere. Any ideas?

Read the article
HP DAT72x6 autoloader

- by ericmayo

Hoping someone here has seen this similar issue and can offer soem advise... I have an HP DAT72x6 auto loader tape backup unit. The external kind, here is a link to an owner's manual I found of it. http://www.dectrader.com/docs/set2/emr_na-c00070400-1.pdf I purchased the unit used about 6 months ago. The unit stopped working after 3-4 back-ups, it's used one day a month to do a monthly backup of another system. Suffice it to say the unit gets very little usage. There is an amber light on the front of the unit called the OAR (Operator Attention Required). The manual states to call for service when this light comes on and stays on. I've tried a few things to resolve but none are working. I've tried power cycling, re-securing the SCSI cables at both ends. Unit was used so I didn't pay much ($500) and so I don't want to spend a lot to have it fixed; might as well buy something new one if fixing this is going to cost more than $100-$150 bucks. I'm curious to see if anyone here has been around these devices or possibly is an HP repair person that can give me some things to try to resolve. The manual states that a solid amber OAR light indicates a hardware failure. When I power cycle the unit I see one of two scenarios so far. The unit powers up, shows self test in the LCD, then LCD changes to show all possible images and the OAR light comes on. The unit powers up, LCD is completely blank, the green lights go through some sort of process of going on and off and later the amber OAR light comes on and stays on. If it's a simple misalignment issue, I may be able to fix myself but not knowing what could cause the OAR light to come on gives me no where to even start. Google around gave no help either. I hoping someone here has experience with this and can help or point me in the right direction. Also, I don't have the HP Diagnostic tools mentioned in many manuals. The unit is connected to a Linux box. The 3-4 backups I've done with it so far have had no issues. We run amanda backup. Before this incident the unit was backing up and reading tapes fine. Thanks for any help or suggestions.

Read the article
Cannot Access Web Interface on HP 2510G

- by Stephen

I am currently setting up a new infrastructure with HP 2510s as edge switches and an HP E5406 as the main switch. I also have a DHCP and DNS server running on the same network. When i first set up one of my 2510 switches, I gave it a static IP through the console and then went to the web interface to continue my configuration. Later, I realized that I assigned it the wrong IP address, so i went through the web interface and changed the IP address to the correct one. Now, I can't access the web interface. I can telnet to the switch on the new IP address, but the web interface will not load. If I switch from static IP to DHCP, it loads the web interface. Any ideas on what could be causing the web server in the 2510 not to load with the new static IP address?

Read the article
HP ML115 with P400 Smart Array Controller

- by John

Hi, I have a HP ML115 server I have installed a HP P400 Smart Array Controller card, I also have 4 x 1TB Samsung Hard drives. I'm unable to get the the controller to detect the hard drives, I have changed the drives to SATA 1.5G without luck, I have also tried connecting a single 80GB Maxtor drive without luck The controller shows up just after boot and tries to initialize, The controller does not show up in the POST prompt, although I can see the controller when booting off a ACU CD THe controller firmware is a little old v4.12 but I have no way to update it. Any ideas on how I can get this going?

Read the article
Restoring factory image of HP Laptop

- by Ahmed

I use a HP G62. I am unable to use my recovery disk to restore to factory settings. I had no problems earlier until I created an additional partition which I hear might have changed my hard disk to dynamic. How do I get back to 'normal'? I don't mind formatting the disk. I just want my factory OS back. .............. i get an error message at about 69 percent telling me that the restoration process failed. I'm using the factory image disks i created using the hp recovery manager. I have tried formating the hard drive clean and then restoring woth the cd, it didn't work. I was always able to restore before i created that partition.

Read the article
HP 1210 Scan Button does nothing.

- by Jack M.

I have an HP 1210 all-in-one nightmare of a printer which has decided not to listen to the scan button anymore. I've dug into it, and see in the properties of the scanner in Windows XP that it says "No applications are registered for this event" under what to do when the Scan button is pressed. I've tried re-installing the HP software, didn't help. Updated the drivers off the website, and downgraded them to the ones on the CD, neither had an effect. Is there any way to tell Windows to just open the Scan/Cammera wizard when I press the Scan button on the printer? Windows XP SP3, if that matters.

Read the article
HP Photosmart 7450 Prints Noise On Windows 7 Pro 64-bit

- by David Mackintosh

I have received a working (in its last location) HP Photosmart 7450 printer. I connected it up to my Windows 7 Pro 64-bit workstation, and the driver was (apparently) installed. The problem is that whenever I try to print from it -- test page, text from notepad, picture, whatever -- it spins through a half dozen sheets of paper, some of which have fractions of text on them, but most of which are either blank or have line noise printed on them. Noise similar to what was printed out on ye olde laserjet printers when the postscript interpreter failed. HP's web site only has a "use the included driver in Windows 7, be happy" instruction. The driver has been removed and added several times. The printer was previously attached to a XP Home computer and worked correctly without incident. Does anyone have any ideas for troubleshooting before I drop this printer in the river?

Read the article
Convert RAID-0 to RAID-1 on HP ML350G6 with P410i zero memory

- by JLe

I have an HP ML350 G6 with a P410i zero memory RAID controller. As far as I can understand that means I can't expand a current single drive "RAID-0" configuration to a RAID-1 using the HP Offline ACU without installing memory and BBWC. Is that correct? What makes me think about this is the fact that expanding RAID-0 to RAID-1 should be pretty similar to replacing a failed drive in an already existing RAID-1? So then why can't I expand without memory and BBWC? Is my best option otherwise to (i) use Ghost to capture the disk, create a new RAID-1 with the existing drive and a new one or (ii) buy memory+BBWC and do it online? Thanks

Read the article
HP CM2320 Printer crashes windows 2003 spooler in TS/Citrix

- by Stephane

Hello, I'm having a very annoying issue with an HP printer (CM2320): all of a sudden, any user who has that printer installed locally as default printer would crash any Windows 2003 terminal services or Citrix server (XenApp PS 4.5) as soon as he connect, causing the session to hang and other users to be unable to connect to the server. To restore functionality, an administrator has to connect to the server's console session and acknowledge the error message about spoolsv.exe having crashed with an AV. I tried downloading the latest drivers from HP (an adventure worthy of Lara Croft in itself) and install it on all servers but that didn't seem to have helped the situation: the spooler is still crashing. Anyone has a suggestion about what I could do about this ?

Read the article
HP LaserJet 1320 printing black boxes instead of text

- by David Gard

I have an HP LaserJet 1320, running off of the HP PCL5 64-bit Universal Driver (Windows 7 Professional, 64-bit). When printing, anything other than body text is blacked out. I.e. on an email, where the 'To...', 'From...', 'CC...' and 'Subect' are usually shown at the top, there is just a black box. And on Word documents, anything to do with Track Changes is also blacked out. I have tried restarting the Print Spooler, and reinstalling the printer, but this does not help. Does anybody know why this is happening?

Read the article
HP DL370 G6 expansion

- by user72185

Hi, we are running a HP DL370 server with 6 x 300 gb disks on RAID 5. Due to a Windows update causing our server to fail recently, we couldn't access the data. I now want to separate the data from the OS (Windows server 2008 r2) so that if anything like that happens again, we can route everyone through a separate server. I have seen these HP storageworks enclosures (msa70) and have a couple of questions: Can I just take out our 2.5 inch 10k SAS drives, install them in the new Storageworks NAS and hey presto we would be up and running? If I wanted to then add another drive (I think there are 25 bays), can I just insert a blank but identical drive and the RAID 5 would dynamically expand to incorporate the new drive. Many thanks Adrian

Read the article
Alternatives for HP ProtectTools on EliteBook 2530p

- by AlexDuggleby

Hi, I'd like to use the HP fingerprint sensor on my Elitebook 2530p. The system is a fresh Win7 Enterprise 64-bit and we are looking for an alternative to the HP ProtectTools Security Suite, which seems a bit bloated. We have tried the UPEK ProtectorSuite (both WBF and stand-alone edition) and they say they can't find the fingerprint device. The device shows up in device manager, in the BioMetric system configuration I have enabled logon to Windows and Domain credentials. Are there any other fingerprint login software (free or commercial) that you can recommend. Thanks in advance, Alex

Read the article
HP Pavilion dv6000 QuickPlay power on

- by user22559

Hello I have a question for HP Pavilion dv6000 owners. If your laptop is powered down, and you press the QuickPlay button or the DVD button (NOT the power button), does the laptop start up? More info: I am asking this because I have got a hold of a broken HP dv6000. If I power it up, the power light lights up, and then the laptop powers down. It seems to be because of a broken motherboard. But the laptop does the same thing if you press the QuickPlay or DVD buttons, and I want to know if that's supposed to happen, or if it's something else that is wrong.

Read the article

< Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13 | Next Page >