Search Results

Search found 817 results on 33 pages for 'ipv6'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 6/33 | < Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >

  • Enterprise IPv6 Migration - End of proxypac ? Start of Point-to-Point ? +10K users

    - by Yohann
    Let's start with a diagram : We can see a "typical" IPv4 company network with : An Internet acces through a proxy An "Others companys" access through an dedicated proxy A direct access to local resources All computers have a proxy.pac file that indicates which proxy to use or whether to connect directly. Computers have access to just a local DNS (no name resolution for google.com for example.) By the way ... The company does not respect the RFC1918 internally and uses public addresses! (historical reason). The use of internet proxy explicitly makes it possible to not to have problem. What if we would migrate to IPv6? Step 1 : IPv6 internet access Internet access in IPv6 is easy. Indeed, just connect the proxy in Internet IPv4 and IPv6. There is nothing to do in internal network : Step 2 : IPv6 AND IPv4 in internal network And why not full IPv6 network directly? Because there is always the old servers that are not compatible IPv6 .. Option 1 : Same architecture as in IPv4 with a proxy pac This is probably the easiest solution. But is this the best? I think the transition to IPv6 is an opportunity not to bother with this proxy pac! Option 2 : New architecture with transparent proxy, whithout proxypac, recursive DNS Oh yes! In this new architecture, we have: Explicit Internet Proxy becomes a Transparent Internet Proxy Local DNS becomes a Normal Recursive DNS + authorative for local domains No proxypac Explicit Company Proxy becomes a Transparent Company Proxy Routing Internal Routers reditect IP of appx.ext.example.com to Company Proxy. The default gateway is the Transparent Internet proxy. Questions What do you think of this architecture IPv6? This architecture will reveal the IP addresses of our internal network but it is protected by firewalls. Is this a real big problem? Should we keep the explicit use of a proxy? -How would you make for this migration scenario? -And you, how do you do in your company? Thanks! Feel free to edit my post to make it better.

    Read the article

  • Configure IPv6 on your Linux system (Ubuntu)

    After the presentation on IPv6 at the first event of the Emtel Knowledge Series and some recent discussion on social media networks with other geeks and Linux interested IT people here in Mauritius, I thought that I should give it a try (finally) and tweak my local network infrastructure. Honestly, I have been to busy with contractual project work and it never really occurred to me to set up IPv6 in my LAN. Well, the following paragraphs are going to shed some light on those aspects of modern computer and network technology. This is the first article in a series on IPv6 configuration: Configure IPv6 on your Linux system DHCPv6: Provide IPv6 information in your local network Enabling DNS for IPv6 infrastructure Accessing your web server via IPv6 Piece of advice: This is based on my findings on the internet while reading other people's helpful articles and going through a couple of man-pages on my local system. Let's embrace IPv6 The basic configuration on Linux is actually very simple as the kernel, operating system, and user-space programs support that protocol natively. If your system is ready to go for IP (aka: IPv4), then you are good to go for anything else. At least, I didn't have to install any additional packages on my system(s). We are going to assign a static IPv6 address to the system. Hence, we have to modify the definition of interfaces and check whether we have an inet6 entry specified. Open your favourite text editor and check the following entries (it should be at least similar to this): $ sudo nano /etc/network/interfaces auto eth0# IPv4 configurationiface eth0 inet static  address 192.168.1.2  network 192.168.1.0  netmask 255.255.255.0  broadcast 192.168.1.255# IPv6 configurationiface eth0 inet6 static  pre-up modprobe ipv6  address 2001:db8:bad:a55::2  netmask 64 Of course, you might have to adjust your interface device (eth0) or you might be interested to have multiple directives for additional devices (eth1, eth2, etc.). The auto instruction takes care that your device is enabled and configured during the booting phase. The use of the pre-up directive depends on your kernel configuration but in most scenarios this might be an optional line. Anyways, it doesn't hurt to have it enabled after all - just to be on the safe side. Next, either restart your network subsystem like so: $ sudo service networking restart Or you might prefer to do it manually with identical parameters, like so: $ sudo ifconfig eth0 inet6 add 2001:db8:bad:a55::2/64 In case that you're logged in remotely into your PC (ie. via ssh), it is highly advised to opt for the second choice and add the device manually. You can check your configuration afterwards with one of the following commands (depends on whether it is installed): $ sudo ifconfig eth0eth0      Link encap:Ethernet  HWaddr 00:21:5a:50:d7:94            inet addr:192.168.160.2  Bcast:192.168.160.255  Mask:255.255.255.0          inet6 addr: fe80::221:5aff:fe50:d794/64 Scope:Link          inet6 addr: 2001:db8:bad:a55::2/64 Scope:Global          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 $ sudo ip -6 address show eth03: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000    inet6 2001:db8:bad:a55::2/64 scope global        valid_lft forever preferred_lft forever    inet6 fe80::221:5aff:fe50:d794/64 scope link        valid_lft forever preferred_lft forever In both cases, it confirms that our network device has been assigned a valid IPv6 address. That's it in general for your setup on one system. But of course, you might be interested to enable more services for IPv6, especially if you're already running a couple of them in your IP network. More details are available on the official Ubuntu Wiki. Continue to configure your network to provide IPv6 address information automatically in your local infrastructure.

    Read the article

  • Gethostname and IPv6

    - by Indhu Bharathi
    Microsoft recommends not to use 'gethostname' on IPv6 and instead use 'getaddrinfo' or 'getnameinfo'. http://msdn.microsoft.com/en-us/library/ms899604.aspx But 'gethostname' doesn't seem to have any problem working on IPv6. Does anyone know any reason why 'gethostname' is not recommended on IPv6?

    Read the article

  • Does Active Directory on Server 2003 R2 support IPv6 subnets in Sites and Services?

    - by NorbyTheGeek
    I've been experimenting with IPv6 at our organization. The domain controllers (all 2003 R2) and most of the servers (2003 R2 / 2008 / 2008 R2) have IPv6 configured. We have a subnet assigned through a tunnel provider. Currently, the only workstation that is running IPv6 is mine. (Windows 7) I have been noticing that my workstation is picking domain controllers in other sites for things like DFS, and I finally realized that I don't have the IPv6 subnets set up in Active Directory Sites and Services (ADSS). But when I try to add a IPv6 prefix in ADSS, it tells me: Windows cannot create the object 2001:xxxx:xxxx:xxxx::/64 because: The object name has bad syntax. I believe I may be using the 2008 version of the admin tools (ADSS reports version 6.1.7601.17514) so I'm wondering if maybe my 2003 R2 Active Directory schema doesn't support configuring IPv6 subnets in ADSS. Is this true? UPDATE Even with 2008 R2 schema in Active Directory, I'm having the same problem. How can I get my IPv6 subnets into Sites and Services?

    Read the article

  • Get IIS 7.5 to listen on IPv6

    - by Matthew Steeples
    I'm using IIS on Windows 7, and I can't get it to bind to the IPv6 equivalent of 0.0.0.0 and 127.0.0.1 ([::] and [::1]) The first one gives me an error when trying to start the service that says The World Wide Web Publishing Service (WWW Service) did not register the URL prefix http://[::]:80/ for site 1. The site has been disabled. The data field contains the error number. The second one doesn't give any errors but doesn't listen on anything apart from 0.0.0.0 The bindings dropdown only has my teredo address (2001::) listed, and not my link local (fe80::) one.

    Read the article

  • IPv6 local address in hosts file

    - by Dan
    I have set up a local domain on my Apache server. Then I added the following line in my /etc/hosts file ::1 exampledomain.local After I trying to navigate to it, (I tried Firefox and Chromium) I got a server not found error. Then I tried ping6 and it worked: dan@danny:~$ ping6 exampledomain.local PING exampledomain.local(exampledomain.local) 56 data bytes 64 bytes from exampledomain.local: icmp_seq=1 ttl=64 time=0.032 ms If I replace ::1 with 127.0.0.1 in my hosts file, it works fine. I'm not sure if this is relevant but this is my Virtual Host configuration in Apache2: <VirtualHost *:80> ServerAlias exampledomain.local DocumentRoot /home/dan/sites/exampledomain <Directory /home/dan/sites/exampledomain> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/exampledomain-error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel debug CustomLog ${APACHE_LOG_DIR}/exampledomain-access.log combined </VirtualHost> My question is: How can I make it work with the IPv6 address?

    Read the article

  • Could not open IPV6 addr on web browser

    - by vito
    I have ipv6 address fe80::21f:a4ff:fe91:2e44%4. This is the address of modem/router. I am unable to open this address in browser to view the web configuration. I am able to telnet to fe80::21f:a4ff:fe91:2e44%4, view the console UI & can do settings. I can also open 192.168.1.1(IPv4 address of modem/router) in browser. I tried [fe80::21f:a4ff:fe91:2e44] in all browsers like IE, Firefox & Chrome. It was not possible.

    Read the article

  • What are the IPv6 Public and Private and Reserved ranges

    - by vipin raj
    I just want to know what are all the public IPv6 ranges which ISPs or other users can use? Also need a list of addresses which can be used in private networks and also the list of addresses which never can be used in any network. I have been searching through different web sites. But none gives a reliable answer. Actually we are developing an application which allows user to plan their IP address(create supernets, subnets, hosts, assign host to ports etc). So my application should be able to distinguish between all kinds of address ranges, whether it is reserved, public, private, multicast etc

    Read the article

  • Automatic DNS population for routable IPV6 addresses

    - by Clint
    In ipv4 I can set my DHCP server to populate DNS with hostnames and IP addresses as clients are found. This works well and clients can resolve these DNS addresses to contact eachother over routed subnets. How can this be done in ipv6 without DHCP? Link Local Multicast Name Resolution can allow clients on the same subnet to discover eachothers hostnames and match them to link-local addresses, but so far I can't find a way for clients to advertise their global or unique local addresses and hostnames to a DNS server to be resolved across subnets.

    Read the article

  • Single ipv6 from /64 subnet

    - by PartyPete
    I have a newb question I'd like to ask. We have an dedicated server and we got an ipv6 /64 block. We want to use squid to make proxy and use those IP. And my question now is: Is it possible to use only one IP out of range? for example: let's say I have a range of IPs ffff:ffff::/64, and want to use only one address from it: ffff:ffff::1/128 or ffff:ffff::2/128 but whenever I set squid like this I always get from 'what is my ip' services whole subnet which is again ffff:ffff::. What I want to achieve is to get from those 'what is my ip' services to send me back IP ffff:ffff::1 (or 2 for that matter) Am I doing something wrong?

    Read the article

  • Debian, 6rd tunnel, and connection troubles

    - by Chris B
    Long story short I am having issues with IPv6 using a 6rd tunnel with my ISP, charter business. They offer a 6rd tunnel that I think I have properly set up, but the server doesn’t reply to every ipv6 request. When the server has the network interfaces idle with no traffic for about 10 minutes, then IPv6 stops accepting inbound connections. to re-allow it, I must go into the server, and make it do a outbound ipv6 connection (normally a ping) to start it back up. Whats weird though i that if I run iptraf when its not working, it still shows a inbound ipv6 packet… the server is just not replying, and I can’t figure out why. Also, if I try to access my server over IPv6 from a house about 1 mile away on the same ISP, it is never able to connect. it always times out, but again the iptraf shows a ipv6 inbound packet. Again, it just does not reply. To test if my server is accessible through IPv6 I always have to use my vzw 4g phone (they use IPv6) or ipv6proxy dot net. Here is all of the configuration information my ISP gives on there tunnel server: 6rd Prefix = 2602:100::/32 Border Relay Address = 68.114.165.1 6rd prefix length = 32 IPv4 mask length = 0 Here is my /etc/network/interfaces for ipv6 (used x's to block real addresses) auto charterv6 iface charterv6 inet6 v4tunnel address 2602:100:189f:xxxx::1 netmask 32 ttl 64 gateway ::68.114.165.1 endpoint 68.114.165.1 local 24.159.218.xxx up ip link set mtu 1280 dev charterv6 here is my iptables config filter :INPUT DROP [0:0] :fail2ban-ssh – [0:0] :OUTPUT ACCEPT [0:0] :FORWARD DROP [0:0] :hold – [0:0] -A INPUT -p tcp -m tcp —dport 22 -j fail2ban-ssh -A INPUT -m state —state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m multiport -j ACCEPT —dports 80,443,25,465,110,995,143,993,587,465,22 -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp —dport 10000 -j ACCEPT -A INPUT -p tcp -m tcp —dport 5900:5910 -j ACCEPT -A fail2ban-ssh -j RETURN -A INPUT -p icmp -j ACCEPT COMMIT and last here is my ip6tables firewall config filter :INPUT DROP [1653:339023] :FORWARD DROP [0:0] :OUTPUT ACCEPT [60141:13757903] :hold – [0:0] -A INPUT -m state —state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m multiport —dports 80,443,25,465,110,995,143,993,587,465,22 -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp —dport 10000 -j ACCEPT -A INPUT -p tcp -m tcp —dport 5900:5910 -j ACCEPT -A INPUT -p ipv6-icmp -j ACCEPT COMMIT So Summary: 1.iptraf always shows IPv6 traffic, so its always making it to the server 2.server stops replying on ipv6 after no traffic for awhile (10 minutesish) until a outbound connection is made, then the process repeats. 3.server is NEVER accessable vi same ISP (yet iptraf still shows ipv6 request) Notes: When I try to access it from the same ISP from across town, even with iptables and ip6tables allowing ALL inbound traffic, this is what iptraf shows. IPv6 (92 bytes) from 97.92.18.xxx to 24.159.218.xxx on eth0 ICMP dest unrch (port) (120 bytes) from 24.159.218.xxx to 97.92.18.xxx on eth1 its strange, like its trying to forward to LAN? (eth1 is LAN, eth0 is WAN) even with the IPv6 address being set in the hosts file to the servers domain name. With iptables set up normally with the above configurations it only says this: IPv6 (100 bytes) from 97.92.18.xxx to 24.159.218.xxx on eth0 Im REALLY stuck on this, and any help would be GREATLY appreciated.

    Read the article

  • How to enable IPv6 glue records (AAAA) in PowerDNS

    - by aef
    I'm running a PowerDNS 3.1 on a Debian Wheezy Beta 4 system. The zone data is accessed through a PostgreSQL database, the server answers to both IPv4 and IPv6 queries. If the DNS-Server knows the A record for one of the name servers referenced by NS records on a zone, it automatically return these A records as additional information to the response on an NS query for that zone. Now even if it knows the AAAA record for one of the name servers of the NS records, it currently does never return an AAAA record as additional information. How can I enable this? Or is there anything I could be doing wrong? Output of dig @ns.mydomain.tld NS mydomain.tld: ;; QUESTION SECTION: ;mydomain.tld. IN NS ;; ANSWER SECTION: mydomain.tld. 86400 IN NS ns3.nsprovider.de. mydomain.tld. 86400 IN NS ns2.nsprovider.de. mydomain.tld. 86400 IN NS ns.mydomain.tld. mydomain.tld. 86400 IN NS ns.nsprovider.de. ;; ADDITIONAL SECTION: ns2.nsprovider.de. 86400 IN A 1.2.3.1 ns.nsprovider.de. 86400 IN A 1.2.3.2 ns.mydomain.tld. 600 IN A 192.0.2.194 ns3.nsprovider.de. 86400 IN A 1.2.3.3 Output of dig @ns.mydomain.tld A ns.mydomain.tld: ;; QUESTION SECTION: ;ns.mydomain.tld. IN A ;; ANSWER SECTION: ns.mydomain.tld. 600 IN A 192.0.2.194 Output of dig @ns.mydomain.tld AAAA ns.mydomain.tld: ;; QUESTION SECTION: ;ns.mydomain.tld. IN AAAA ;; ANSWER SECTION: ns.mydomain.tld. 86400 IN AAAA 2001:db8:100:3022:1::3

    Read the article

  • Virtual IPv6 Network between VirtualBox VMs

    - by Ben
    I'm trying to create a virtual IPv6 network as a test environment. I have 5 VirtualBox VMs (Ubuntu Server) with network adapters using host-only networking. You can imagine them being connected in series and every machine connects 2 subnets. I want to ping the last machine from the first one: On: 2001:db8:aaaa::100 I want to ping 2001:db8:dddd::101 (Note: there is no cccc network in between) Only static configuration and routes are used: /etc/network/interfaces auto eth0 iface eth0 inet6 static address 2001:db8:aaaa::100 netmask 64 /etc/network/interfaces auto eth0 iface eth0 inet6 static address 2001:db8:aaaa::101 netmask 64 auto eth1 iface eth1 inet6 static address 2001:db8:bbbb::100 netmask 64 up ip -6 route add 2001:db8:dddd::/64 via 2001:db8:bbbb::101 dev eth1 down ip -6 route del 2001:db8:dddd::/64 via 2001:db8:bbbb::101 dev eth1 I thought there might be some automatic route discovery going on. Anyway, ping6 2001:db8:dddd::100 will not work from aaaa::100 When I add the route: ip -6 route add 2001:db8:dddd::/64 via 2001:db8:aaaa::101 it will work. But the next interface in the same network dddd::101 is not reachable. How could that be? There is a machine with an interface bbbb::101 and another dddd::100 and I can ping the latter one, but the machine connected to it, dddd::101 not?? I also have also turned on forwarding. Any ideas?

    Read the article

  • Asterisk: Forcing a sip peer to connect via ipv6?

    - by growse
    I've got an asterisk server that connects to an upstream provider over a WAN. The upstream provider supports both IPv4 and IPv6 connectivity, and the asterisk server is behind a NAT. When asterisk connects to the upstream sip peer via IPv6, everything works perfectly. The issue I have is that when I configure the asterisk server IPv6 address via DHCPv6, a race condition means that asterisk sometimes ends up attempting to contact the upstream peer via IPv4 (the SIP DNS name has both A and AAAA records). This is because asterisk starts up before the system has a valid IPv6 address. The connection does not work via IPv4 because of the NAT. Is there a way of configuring the peer to specify that it should only be contactable over IPv6? I guess it might be possible to hack together a firewall rule to deny all IPv4 traffic to that IP, but it'd be easier to configure this within asterisk itself.

    Read the article

  • How to prefer ipv6 over ipv4 only for specific websites?

    - by kria
    I only have ipv6 connectivity via a HE tunnel on my router, so normally I want to prefer ipv4 over ipv6. For some websites however, I would like to prefer ipv6. Right now I have just set DisabledComponents to 0x20 and hard coded the ipv6 resolution into my hosts file for the sites i want to access over ipv6. Since these ip addresses change at times, this is not a good solution. Any ideas on how to handle this in a non-clunky way? Some kind of Chrome/Firefox add-on might do the trick, but I couldn't find one for this purpose.

    Read the article

  • How can I make IPv6 on OpenVPN work using a tap device?

    - by Lekensteyn
    I've managed to setup OpenVPN for full IPv4 connectivity using tap0. Now I want to do the same for IPv6. Addresses and network setup (note that my real prefix is replaced by 2001:db8): 2001:db8::100:0:0/96 my assigned IPv6 range 2001:db8::100:abc:0/112 OpenVPN IPv6 range 2001:db8::100:abc:1 tap0 server side (set as gateway on client) 2001:db8::100:abc:2 tap0 client side 2001:db8::1:2:3:4 gateway for server Home laptop (tap0: 2001:db8::100:abc:2/112 gateway 2001:db8::100:abc:1/112) | | | (running Kubuntu 10.10; OpenVPN 2.1.0-3ubuntu1) | wifi | | router | | OpenVPN INTERNET | eth0 | /tap0 VPS (eth0:2001:db8::1:2:3:4/64 gateway 2001:db8::1) (tap0: 2001:db8::100:abc:1/112) (running Debian 6; OpenVPN 2.1.3-2) The server has both native IPv4 and IPv6 connectivity, the client has only IPv4. I can ping6 to and from my server over OpenVPN, but not to other machines (for example, ipv6.google.com). Using tcpdump on both the server and client, I can see that packets are actually transferred over tap0 to eth0. The router (2001:db8::1) send a neighbor solicitation for the client (2001:db8::100:abc:2) to eth0 after it receives the ICMP6 echo-request. The server does not respond to that solicitation, which causes the ICMP6 echo-request not be routed to the destination. How can I make this IPv6 connection work?

    Read the article

  • Converting IPv4 or IPv6 address to a long for comparisons

    - by Justin Akehurst
    In order to check if an IPv4 or IPv6 address is within a certain range, I've got code that takes an IPv4 address, turns that into a long, then does that same conversion on the upper/lower bound of the subnet, then checks to see if the long is between those values. I'd like to be able to do the same thing for IPv6, but saw nothing in the Python 2.6 standard libraries to allow me to do this, so I wrote this up: import socket, struct from array import array def ip_address_to_long(address): ip_as_long = None try: ip_as_long = socket.ntohl(struct.unpack('L', socket.inet_pton(socket.AF_INET, address))[0]) except socket.error: # try IPv6 try: addr = array('L', struct.unpack('!4L', socket.inet_pton(socket.AF_INET6, address))) addr.reverse() ip_as_long = sum(addr[i] << (i * 32) for i in range(len(addr))) except socket.error as se: raise ValueError('Invalid address') except Exception as e: print str(e) return ip_as_long My question is: Is there a simpler way to do this that I am missing? Is there a standard library call that can do this for me?

    Read the article

  • 'IPv6' Newbie with IPv6 address assigment

    - by Cute Puppy
    I am new to IP v6 and I am looking to translate some existing private IPv4 addresses into v6 address assignment. Can someone please help me to answer/explain the questions below? If I have an v4 address of: 10.10.0.0/22 10.10.1.0/22 10.10.2.0/22 10.10.3.0/22 10.10.8.0/20 10.20.1.0/24 What will the new v6 address to be? I have been looking online @ http://www.subnetonline.com/pages/subnet-calculators/ipv4-to-ipv6-converter.php or other sites, Seems like they translated it directly to be: fe80::a0a:0 /118 fe80::a0a:100 /118 fe80::a0a:200 /118 fe80::a0a:300 /118 fe80::a0a:800 /118 fe80::a14:100 /120 Can someone please explain to me how we get to /118 from either "/22 or /24" (1. and 5) In addition, I would like to create the new private address based on the Unique local address "fc00::/16" How do I expand from there? Any help is greatly appreciated it!! Thanks,

    Read the article

  • Store IPv6 in database

    - by poru
    What's the best practise to store IP's with PHP in MySQL database? There's a function called ip2long - but this is just for IPv4. But what about IPv6? I know a php function that is for IPv6 IP's, but it doesn't work on Windows with PHP < Version 5.3

    Read the article

  • PHP Disabling ipv6

    - by Dave C
    Hello, It seems that I need to somehow disable IPv6 on my php pages, but I am not sure how to do this. I think I have to add --disable-ipv6 somewhere into my INI file... this doesnt look like proper syntax though. I am trying to solve the following bug: http://bugs.php.net/45519 Does anyone know where to put this?

    Read the article

  • Ruby IpV6 Multicast Sending and Receive

    - by Francesco Vollero
    Hi, as object i'm tring to create a client and server scripts in order to send and receive multicast packages over IPv6. In IPv4 everything work as well, but i cannot figure out how to change it in IPv6. I start as basis from Multicasting In Ruby but seems ff02::1 isnt good for MULTICAST_ADDR. Thanks in advance.

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >