Search Results

Search found 6288 results on 252 pages for 'credit card'.

Page 60/252 | < Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >

• How to stream sound from an esx virtual machine ?

  - by Adrien

  Hi, I try to play sound from my monitoring application, which is an xp virtual machine on VMware ESX 3, on a physical machine with a real sound card, but I can not add from the ESX console sound card. Currently, I transmit sound with opening an RDP session and play it in this session. I would like to play sound without openning RDP session, do you have a solution to add a virtual sound card and then stream it with vlc?

  Read the article

• Only two monitor ports are detected on nVidia Quadro NVS 450

  - by Erick Robertson

  I have an nVidia Quadro NVS 450 installed in a Dell Optiron 380. Only DisplayPort #1 and DisplayPort #4 are detected by windows. The machine has a BIOS setting to automatically choose the primary video card, or to disable the primary when a PCI-e card is installed (which it is). Windows cannot see DisplayPort #2 and #3 no matter what I do. I have tried the Windows Drivers, latest nVidia Drivers - no dice. I am assured that this video card cannot break in this way. I'm plum out of ideas. I've tried reseating the video card. I've contacted Dell and they've remoted in and looked around - threw their arms up after two hours. Any ideas? I'm running Windows 7 64-bit. All four monitors are 1600x1200 Dell monitors.

  Read the article

• How to use Ralink RT2501/RT2573 as wifi access point in Debian Linux

  - by user60813

  Hi, I have a fit-PC server with Debian GNU/Linux (Lenny). I would like to use it as a wifi access point since my Linksys WRT54GS has become unstable. I have a USB Ralink wifi NIC. When I insert the card to USB I can see this with lsusb: Bus 001 Device 002: ID 148f:2573 Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter I have tried following various HOWTOs on using wifi card as AP in Linux, however, it seems that the card cannot go into monitor mode. I believe this is because I must use a newer driver or upload non-free firmware or something like that. I have tried installed wicd, but it does not help. I bought this wifi adapter because I was told that it is one of the most common used Linux supported wifi cards that can be used as access point and a lot of other stuff. So my question is: How do I set up this USB wifi card as wireless access point in Debian Lenny?

  Read the article

• Diagnosing PCI issues

  - by dtsazza

  I'm upgrading a PC for a friend, and have run into a problem with upgrading the motherboard. I've been assembling custom PCs for the best part of a decade now, so I'm happy enough with the basics at the very least. The motherboard, CPU and graphics card were all updated at once - after this was done, the machine POSTs but the PCI wireless card, as well as the PCI-E graphics card, do not seem to be recognised at all by the system. No trace of them anywhere in the BIOS, or the POST output, or in Windows. I booted into Linux and ran an lspci which also showed up no sign of them. What is the best step to go about diagnosing this? Is it likely/feasible that the motherboard's PCI bus is just defective and it needs to be RMAed? Are there any other common gotchas that might cause these symptoms? For reference, the components in question are: CPU: Celeron E1400 Motherboard: Gigabyte GA-G31M-ES2L Graphics card: TBC (a low end card from a couple of years ago; worked flawlessly before the mobo change) PCI WNIC: Edimax 7128G Thanks in advance for any help.

  Read the article

• Why my new GTX 660m's clock drops drastically after running few seconds

  - by trVoldemort

  I bought a Lenovo Y580 laptop few days ago, this model is equipped with GTX 660m graphics card. However, the game performance is unbelievably poor since it out from the box. I realized there is something wrong with this graphics card. I downloaded GPU-z, and did a simple test. And I was shocked by the fact that my GTX 660m graphics card is running at 135.0mhz core clock. (It should be 835mhz at least!) Even the integrated graphics card "Intel HD graphics 4000" can run at 650mhz. Further examining showed that in the first few seconds GTX 660m was actually running at 835mhz, however the core temperature quickly reached 90+°C and the clock (maybe) automatically drop to 135.0mhz. This is very strange. Anyone has any idea what's going on here?

  Read the article

• how to enable opengl 2.0 and webgl on gma 3150 on ubuntu?

  - by mahmoudelbadry

  hi, i have a dell mini 1012 which an intel n450 processor and gma 3150 integrated graphics card running ubuntu 10.10 according to the intel website the graphics card support opengl 2.0 http://software.intel.com/en-us/arti...ed-graphics/#9 but when i type glxinfo in terminal the opengl version string gives me the following OpenGL version string: 1.4 Mesa 7.9-devel i installed the latest drivers but it didn't work so, how can i enable opengl 2.0 on this card?? thanks

  Read the article

• How to determine the root cause of a system lockup on Ubuntu 8.04 LTS?

  - by jdt141

  I'm currently working a project that involves setting up a PC/104 stack and running Ubuntu 8.04 LTS. We need to use the PC/104 stack because its an embedded application - and we're required to use a DeviceNet peripheral card to communicate to other devices. (DeviceNet is just a protocol on top of CAN.) Anyway, the following hardware is on the stack: Kontron MOPSPM104 with a 1GHz Intel Celeron processor ConnectTech FlashDrive/104 4GB Industrial Temp (-40 to +85 C) Woodhead (Molex) PC104DVNIO DeviceNet card A run of the mill 104 power supply The Kontron Board offers two serial ports, one VGA out, and two USB ports. The DeviceNet card is an ISA card. Because of this (per the User's Guide for the Kontron Board), I have manually set the IRQs in the BIOS to be appropriately configured, and turned off ACPI in both the BIOS and passed the appropriate flag in GRUB. I've installed Ubuntu 8.04 desktop, 32 bit. The problem that I'm having is that, from time to time, the entire 104 stack locks up. This only seems to happen in two cases, both of which we're running GNOME. We have a custom application that uses the DeviceNet card, and the system will lock up, or (more frequently) when we're running Firefox and either surfing for some information or trying to test it - typically by streaming video from a IP-camera. The reason I ask this questions is I cannot determine the root cause of this lockup. The IRQs appear to correctly configured in the BIOS and as the Kernel sees them, and nothing is logged to dmesg. If you all could help me determine the root cause of this lockup, I would greatly appreciate it. Thanks.

  Read the article

• Windows XP does not list WPA wireless networks

  - by Tomalak

  What can be the reason that Windows XP does not show WPA-encrypted wireless networks? The laptop I have problems with is an older model (Toshiba Satellite Pro 6100) with Windows XP SP3 on it, fresh install. The wireless network card in it is an Agere product that lists as "Toshiba Wireless LAN Mini PCI Card". The networks showed up perfectly before I first tried to connect to one (it was set to WPA2). The connection failed (the card supports WPA only), then something must have happend and Windows hides these networks now. A manually configured WPA setup via Windows' own wizard works, I'm using it right now. The network just won't show up in the list of available network on its own. I suspect that XP incorrectly set a flag somewhere that this network card does not support WPA. Is there such a flag, and if so, how can I change it back?

  Read the article

• Is it possible to dedicate the physical screen of a vmware server machine to a guest vm graphically?

  - by matnagel

  I have a vmware server 2.x running on ubuntu server (8.04). So the graphics card and the screen of the physical box are unused (I log in remotely and the host os has only the cli console installed). I wonder if it is possible to assign this graphics card to a virtual machine directly and use it for the gui of this guest? Or maybe if I add a second graphics card to the machine?

  Read the article

• Is it safe to have NVidia graphics always on on a Linux laptop, or do I risk overheating?

  - by codeape

  I'm getting a Lenovo T520 with two graphics cards: Integrated Intel HD 3000 Discrete NVidia NVS 4200M In BIOS, I can adjust which card(s) to use: Integrated only Discrete only Both (NVidia optimus) Since optimus is not well supported under Linux, I wonder if it is OK to set up the system to use the NVidia card all the time. I have read somewhere that a laptop risks overheating if using a discrete graphics card all the time. Is this true? Does someone have any experience to share?

  Read the article

• I'm using a compatible active DisplayPort to DVI adapter with EyeFinity, why does my monitor still flicker?

  - by Christopher Galpin

  I specifically chose an active DisplayPort <- DVI adapter for use with EyeFinity right out of my graphic card vendor's list of confirmed compatible adapters. Yet the screen fails horribly, it blinks on and off constantly, sometimes the graphics go screwy and the appropriate resolutions won't be available. Sometimes the resolution will be available but I'll discover it's only with interlaced refresh rates and bounces up and down. I have to switch the resolution back and forth, again and again, to get it to work correctly, and then it fails again and the process must be repeated the moment the monitor is turned off or I reboot. It's maddening. What is wrong? Is my GFX card supplying insufficient voltage? (Firmware tweaks allegedly help some people, but my card's isn't modifiable.) Could the adapter be defective? Is it not "active" enough for my card and I need an expensive powered adapter? Is this endemic to DisplayPort in general?

  Read the article

• Building My First Computer And Suprise It Isn't Working

  - by BobbShots

  I've had many years of experience working on and around computers, but this was my first foray into building one completely from scratch. So far that foray has been a disaster. My rig is completely assembled, and on its maiden power-up plus many power cycles I noticed three things: There were a few beeps from the BIOS POST upon powering up the first time, but I wasn't paying attention completely to the sequence. However, every time after that there are 0 POST beeps, even after taking off all hardware except the CPU and MB. There was no video being sent to the monitor. I run a HDMI cable from my video card to the monitor. The video card was LOUD. My card is a Sapphire Radeon HD 5870 which is known for not only being a powerhouse, but being pretty quiet. A few times during my power cycles it ran a lot quieter, but most of the time it was just super loud. Can anyone provide help for any of these issues? My MB, CPU, and Video Card are: MB: ASUS P6X58D Premium LGA 1366 Intel X58 SATA 6Gb/s USB 3.0 ATX Intel Motherboard CPU: i7 920 Video Card: Sapphire Radeon HD 5870

  Read the article

• How can I get multiple video cards to work on linux?

  - by user17943

  I installed fedora 12. I have 2 ATI cards that I used to use on windows to run 4 monitors. A recurring problem has been to get them detected in linux. Only my secondary card is picked up linux. When I manage the displays it detects the 2 monitors connected that card. What are the specific steps I should take to get the second card detected? Supposedly there is a tool system-config-xfree. I don't have it, yum can't find it. Also I heard it has something to do with editing some xorg.conf file or something to that effect. I have absolutely no idea how to find the "bus id" of my card, or lookup the horizontal refresh rates, etc.. I would probably have no problem following the documentation & editing the file if I knew a good way to find these values. Someone also suggested installing linux twice and saving the xorg.conf it generates each time (with different card each time) and then merging the two by hand. That is like killing a fly with a hammer though, when I do this again and again in the future It'd be nice to not have to take twice as long. Thanks

  Read the article

• Windows 7: from Geforce 8800 to three monitors?

  - by lance

  I've got a GeForce 8800 that I've quite happy with. It drives my two 23" widescreen displays well. Now I've got a 19" standard display that I want to stick between the two widescreens. My second PCIe 16x slot is unused (as is the PCI slot below that), and I want to add a card to my Win7 x64 system. This 19" display won't be used for gaming, so I don't need anything fancy. Here are two cards I was considering, but I'm wondering if they're bad choices for some reason? If they're both fine choices, which is better and why? Again, I'm needing to power only the 19" standard display with this card, and it won't play games. I just need 1280x1024 in Win7 x64. NVidia: Galaxy 95TFE8HUFEXX GeForce 9500 GT Video Card - 512MB DDR2, PCI Express 2.0 ATI: ASUS EAH4350 SILENT/DI/51 Radeon HD 4350 Video Card - 512MB DDR2, PCI Express 2.0

  Read the article

• Why is the pavucontrol level indicator jumping while nothing plays?

  - by EnterTheLiquidToasterFamily

  The level indicator in the screenshot does jump around even if nothing is playing. The indicator also reasonably represents sound levels when music is playing. I dont have any mediaservers running or noisy browsertabs open. Also no mic connected. When I turn the volume to max in software and on the amp, there is no noise from the speakers at all. Played music is loud and not distorted. Hardware: Realtek ALC889 over optical audio connector to a generic amp. Software: Debian Wheezy with latest backport kernel 3.14 (same thing on wheezy 3.2 stock), wheezy pulseaudio, xfce session, a custom asound.conf that enables pulseaudio to push sound over optical port. /etc/asound.conf pcm.a52 { @args [CARD] @args.CARD { type string } type rate slave { pcm { type a52 bitrate 448 channels 6 card $CARD } rate 48000 #required somehow, otherwise nothing happens in PulseAudio } }

  Read the article

• Failover Internet connection?

  - by ez_brian0

  Hi In my Linux server i have three network cards. The eth0 card is connected to ISP1, the eth1 card is connected to LAN and the eth3 card is connected to ISP2. What i want to do is to automatically use eth3 as Internet connection if the eth0 connection fails. How can this be done? Another problem is that my firewall is referring to eth0 as the server is doing NAT for clients this would be broken if eth3 is taken in use, how can this be solved?

  Read the article

• Run 3 monitors on two different video cards?

  - by hullot

  Can I run 3 monitors on two different video cards? I have an ATI and Nvidia brand card. The ATI has 2 HDMI connections. They both work. Both cards are also picked up in Windows, one being the ATI and the other one as the Nvidia, but it says VGA Controller, although the card only takes 2 DVi. So, one DVI cable goes into that Nvidia card. 3 Monitors, but only 2 the HDMI ones from the ATI pick up, not the third one which is connected to the Nvidia via DVI. How can I run three monitors then? I suppose I can't install both drivers, so I'm unsure what to do. Is this possible? I just want the Nvidia card to power the third screen, no gaming on it, nothing. Also the ATI is picked up as primary card as well, so no hurdle there. EDIT: Hm, just installed the Nvidia drivers and it picked up the third screen no problem. Hope there aren't any major conflicts. Will post this as an answer as correct when I'm able. Can't as a new user.

  Read the article

• Windows 7 Taskbar Icons Randomly Disappearing

  - by Ryker

  This is a problem that i'm totally stumped on. Taskbar Icons that are pinned, as well as open program thumbs keep disappearing. This is totally random, no set pattern. I've tried updating drivers for the vid card, rolling back to old drivers, nothing seems to work. I've also tried the usual uncheck hide the taskbar and recheck, changing the start menu, keeping commonly used programs in start menu, etc. This is using an add-in card which is a necessity. Here is the specs on the machine: New Dell Optiplex 390 i3 2100 Proc 3gb Ram, Windows 7 32-bit. The add in card is an Nvidia 8400 GS model. I've tried different versions of the 8400gs, from MSI, or from other manufactureres and regardless it keeps happening. After the Icons disappear, I can log out and log back in and they return, but disappear again. I can reinstall the drivers for the vid card and it fixes it for a few days, and then they disappear again. There isn't any set pattern of days that it happens, software being used, etc. Another user in the office had the same problem with the exact same machine, but updating the vid card drivers fixed the issue. Anyone?

  Read the article

• Program for managing multiple monitors to keep from rearranging Windows

  - by Rumel

  I have a setup in use where I use up to four monitors. The problem is I generally switch around what I'm using and that messes up where all of my windows are. I'm on Windows 8 and have two graphics cards. My setup is as follows: Monitor 1: Card 1 Monitor 2: Card 1 Monitor 3: Card 2 TV 1: Card 2 I almost always have all the monitors turned on and in use. When I turn on the TV though, all of my windows get reconfigured and moved to different monitors. I don't know how to stop this. Another configuration I use is where I have Monitors 1 and 2 plus TV in use, and I have my Xbox in use on Monitor 3. When I get done with the Xbox and switch Monitor 3 over to the PC, everything is reconfigured. So is there a program out there that can help with this? I have the free version of Display Fusion in use but haven't seen settings to save monitor configurations.

  Read the article

• Debian - no sound output

  - by Gogeta70

  So I've been trying for the last few days to get sound output on my Linux desktop. The onboard audio is Intel HD Audio ICH9, but I couldn't get Alsa to even detect it, so I disabled it in BIOS and installed a PCI card - a Dynex DX-SC51. Searching around, I found that it needed the Alsa driver for ice1724, so I installed all the stuff for that. Now, the system detects my sound card, but I can't get any audio to play out of it. Here's some information: root@debian:~# lspci | grep audio 02:01.0 Multimedia audio controller: VIA Technologies Inc. VT1720/24 [Envy24PT/HT] PCI Multi-Channel Audio Controller (rev 01) root@debian:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: ICE1724 [ICEnsemble ICE1724], device 0: ICE1724 [ICE1724] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: ICE1724 [ICEnsemble ICE1724], device 1: ICE1724 IEC958 [ICE1724 IEC958] Subdevices: 1/1 Subdevice #0: subdevice #0 I've been trying various solutions found on Google for a few days now and I'm getting nowhere. Hopefully someone here can point me in the right direction. Thanks.

  Read the article

• Ubuntu 12.04.1 Radeon 9550 stuck with 640x480, works in Geexbox

  - by Betty

  I am a complete new user trying to set up Ubuntu on an old desktop. It has an AGP Radeon 9550 graphics card. I am running Ubuntu from a USB drive with persistence as the PC currently has no hard drive I seem to be stuck in 640*480 mode. The desktop itself is larger, but the monitor display is stuck on 640*480. In SettingsDisplays, only the 640*480 option is available. What I have found out so far: The proprietary ati drivers no longer support my card. If 3D isn't an issue (it's not) the open source driver should be fine. This should be installed by default so in theory I am using it already xserver-xconf/pci/*.ids doesn't show any entries for the card's PCI id. hardware additional drivers show no proprietary drivers I tried the booting into the current version of Geexbox from a USB stick and this set the resolution correctly by default so I know it can be done, but I know no idea how. How can I tell what driver the card is using, and how can I get the higher resolutions back?

  Read the article

• Suspending my laptop breaks ethernet over firewire, are there commands which can fix it?

  - by Josh

  As mentioned in this question I am using a firewire cable to provide a private network between my laptop and my desktop, because it makes using the screen sharing program synergy much nicer than using WIFI. However when I leave my office for the day and I suspend my laptop, when I return the next day, the desktop and the laptop cannot communicate over firewire anymore. The firewire0 device still has an IP address. but when I try and ping the desktop I get no route to host I'm using kernel 2.6.35-24-generic #42-Ubuntu SMP x86_64 on Ubuntu 10.10. Is there some way I can remedy this without a reboot? Like, removing some kernel modules and re-inserting them? Here's what I have tried so far and the results: root@token:~# dmesg|tail -n 1 [592525.204024] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 root@token:~# modprobe -r firewire_net firewire_ohci firewire_core root@token:~# modprobe -v firewire_ohci insmod /lib/modules/2.6.35-24-generic/kernel/lib/crc-itu-t.ko insmod /lib/modules/2.6.35-24-generic/kernel/drivers/firewire/firewire-core.ko insmod /lib/modules/2.6.35-24-generic/kernel/drivers/firewire/firewire-ohci.ko root@token:~# dmesg|tail [592525.204024] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592563.410868] firewire_ohci: Removed fw-ohci device. [592579.160086] firewire_ohci: Added fw-ohci device 0000:02:00.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2 [592579.160137] firewire_ohci: isochronous cycle inconsistent [592579.660294] firewire_core: created device fw0: GUID 0000000000000000, S400 [592579.663805] firewire_core: created device fw1: GUID 0017f2fffe89bce6, S400 [592579.663813] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592579.700720] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [592579.700842] firewire_core: refreshed device fw0 [592579.702603] firewire_net: firewire0: IPv4 over FireWire on device 0000000000000000 root@token:~# ping stan.firewire PING stan.firewire (192.168.100.1) 56(84) bytes of data. From token.local (192.168.100.3) icmp_seq=1 Destination Host Unreachable From token.local (192.168.100.3) icmp_seq=2 Destination Host Unreachable From token.local (192.168.100.3) icmp_seq=3 Destination Host Unreachable I also tried removing the modules prior to suspending, and re-inserting after resuming. This did not work either :-(

  Read the article

• Dlink DWA-643 ExpressCard / Atheros AR5008 can't connect to wifi networks

  - by Justin Kelly

  I've just purchased a D-Link DWA-643 Xtreme N ExpressCard Notebook Adapter - but it can't connect to my wireless network The card is listed on the FSF website and - refer links below: http://www.fsf.org/resources/hw/index_html/net/wireless/index_html/cards.html http://www.dlink.com.au/products/?pid=550 Ubuntu see the card as using the Atheros AR5008 chipset - refer image below The card lights up and I can see that available wifi networks using this card - so it seems to 'just work' on ubuntu 12.04 but when i try and connect to my networks - it fails I've tried setting the network to all the different options (WEP, WPA2, no encryption, etc.. b/g/n ) but ubuntu sill cant connect to it I've also installed wicd but still couldn't connect Has anyone got a DWA-643 to work in Ubuntu? Or does anyone have any suggestion on how to get it to connect?? Any help would be greatly appreciated Note: the laptop has built in wifi but its broadcom, works but with dialup speed connection - and i've had nothign but trouble using the boardcom drivers so purchased the FSF recommended PCI expresscard as i hoped it would 'just work' on the latest Ubuntu i've have tried to disable the built in wifi - broadcom - but even with the broadcom uninstall and unavailable it didnt help the dlink to connect previously I had MAC address filtering on the router - i've added the dlinks MAC - and also disabled MAC address filtering - still no luck lspci output below: 18:00.0 Network controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) Subsystem: D-Link System Inc Device 3a6f Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at e4000000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Kernel driver in use: ath9k Kernel modules: ath9k

  Read the article

• nvidia graphics resolution problem

  - by Deepak Adhikari

  I am currently using ubuntu 12.04 I have acer aspire timelinex 3830tg with 2GB nvidia GeForce GT540M graphics card To enable my graphics card I followed following steps. 1.) I activated nvidia_current and nvidia_current_updates from additional drivers 2.) sudo nvidia-xconfig 3.) then reboot Following these steps I got following errors 1.) my resolution is 640x480...(there is no option of 1366x768 in display...previously there was 1366x768 when nvidia-xconfig command was not entered) 2.) when I open nvidia-settings it shows me following error "You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run 'nvidia-xconfig' as root) and restart the X server." Problem need to be solved 1.) Change resolution to 1366x768 2.) Also how to check my nvidia graphics working or not Please some one please help me to solve these issues...I am seriously in need of my graphics card... I wan't my nvidia graphics card work as my intel graphics smoothly I am not willing to use bumblebee with regards, ubuntu user

  Read the article

• Direct IO enhancements in OVM Server for SPARC 2.2(a.k.a LDoms2.2)

  - by user12611315

  The Direct I/O feature has been available for LDoms customers since LDoms2.0. Apart from the latest SR-IOV feature in LDoms2.2, it is worth noting a few enhancements to the Direct I/O feature. These are: Support for Metis-Q and Metis-E cards. These cards are highly requested for support and are worth mentioning because they are the only combo cards containing both FibreChannel and Ethernet in the same card. With this support, a customer can have both SAN storage and network access with just one card and one PCIe slot assigned to a logical domain. This reduces cost and helps when there are less number of slots in a given platform. The following are the part numbers for these cards. I have tried to put the platforms on which each card is supported, but this information can get quickly outdated. The accurate information can be found at the Support Document.  Card Name  Part Number  Platforms Metis-Q: StorageTek Dual 8Gb Fibre Channel Dual GbE ExpressModule HBA, QLogic SG-XPCIEFCGBE-Q8-N  SPARC T3-4, T4-4 Metis-E: StorageTek Dual 8Gb Fibre Chanel Dual GbE ExpressModule HBA, Emulex SG-XPCIEFCGBE-E8-N SPARC T3-4, T4-4  Additional cards added to the portfolio of supported cards. This is mainly Powerville based Ethernet cards, the part numbers for these cards as below:  Part Number  Description  7100477 Sun Quad Port GbE PCI Express 2.0 Low Profile Adapter, UTP  7100481 Sun Dual Port GbE PCI Express 2.0 Low Profile Adapter, MMF  7100483 Sun Quad Port GbE PCI Express 2.0 ExpressModule, UTP  7110486 Sun Quad Port GbE PCI Express 2.0 ExpressModule, MMF    Note:  Direct IO feature has a hard dependency on the Root domain(PCIe bus owner, here Primary domain). That is, rebooting the Root domain for any reason may impact the logical domains having PCIe slots assigned with Direct IO feature. So rebooting a root domain need to be carefully managed. Also apply the failure-policy settings as described in the admin guide and release notes to deal with unexpected cases.

  Read the article

< Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >