Search Results

Search found 16086 results on 644 pages for 'screen scraping'.

Page 601/644 | < Previous Page | 597 598 599 600 601 602 603 604 605 606 607 608  | Next Page >

• How to Assign a Static IP Address in XP, Vista, or Windows 7

  - by Mysticgeek

  When organizing your home network it’s easier to assign each computer it’s own IP address than using DHCP. Here we will take a look at doing it in XP, Vista, and Windows 7. If you have a home network with several computes and devices, it’s a good idea to assign each of them a specific address. If you use DHCP (Dynamic Host Configuration Protocol), each computer will request and be assigned an address every time it’s booted up. When you have to do troubleshooting on your network, it’s annoying going to each machine to figure out what IP they have. Using Static IPs prevents address conflicts between devices and allows you to manage them more easily. Assigning IPs to Windows is essentially the same process, but getting to where you need to be varies between each version. Windows 7 To change the computer’s IP address in Windows 7, type network and sharing into the Search box in the Start Menu and select Network and Sharing Center when it comes up.   Then when the Network and Sharing Center opens, click on Change adapter settings. Right-click on your local adapter and select Properties. In the Local Area Connection Properties window highlight Internet Protocol Version 4 (TCP/IPv4) then click the Properties button. Now select the radio button Use the following IP address and enter in the correct IP, Subnet mask, and Default gateway that corresponds with your network setup. Then enter your Preferred and Alternate DNS server addresses. Here we’re on a home network and using a simple Class C network configuration and Google DNS. Check Validate settings upon exit so Windows can find any problems with the addresses you entered. When you’re finished click OK. Now close out of the Local Area Connections Properties window. Windows 7 will run network diagnostics and verify the connection is good. Here we had no problems with it, but if you did, you could run the network troubleshooting wizard. Now you can open the command prompt and do an ipconfig  to see the network adapter settings have been successfully changed.   Windows Vista Changing your IP from DHCP to a Static address in Vista is similar to Windows 7, but getting to the correct location is a bit different. Open the Start Menu, right-click on Network, and select Properties. The Network and Sharing Center opens…click on Manage network connections. Right-click on the network adapter you want to assign an IP address and click Properties. Highlight Internet Protocol Version 4 (TCP/IPv4) then click the Properties button. Now change the IP, Subnet mask, Default Gateway, and DNS Server Addresses. When you’re finished click OK. You’ll need to close out of Local Area Connection Properties for the settings to go into effect. Open the Command Prompt and do an ipconfig to verify the changes were successful.   Windows XP In this example we’re using XP SP3 Media Center Edition and changing the IP address of the Wireless adapter. To set a Static IP in XP right-click on My Network Places and select Properties. Right-click on the adapter you want to set the IP for and select Properties. Highlight Internet Protocol (TCP/IP) and click the Properties button. Now change the IP, Subnet mask, Default Gateway, and DNS Server Addresses. When you’re finished click OK. You will need to close out of the Network Connection Properties screen before the changes go into effect.   Again you can verify the settings by doing an ipconfig in the command prompt. In case you’re not sure how to do this, click on Start then Run.   In the Run box type in cmd and click OK. Then at the prompt type in ipconfig and hit Enter. This will show the IP address for the network adapter you changed.   If you have a small office or home network, assigning each computer a specific IP address makes it a lot easier to manage and troubleshoot network connection problems. Similar Articles Productive Geek Tips Change Ubuntu Desktop from DHCP to a Static IP AddressChange Ubuntu Server from DHCP to a Static IP AddressVista Breadcrumbs for Windows XPCreate a Shortcut or Hotkey for the Safely Remove Hardware DialogCreate a Shortcut or Hotkey to Eject the CD/DVD Drive TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Nice Websites To Watch TV Shows Online 24 Million Sites Windows Media Player Glass Icons (icons we like) How to Forecast Weather, without Gadgets Outlook Tools, one stop tweaking for any Outlook version Zoofs, find the most popular tweeted YouTube videos

  Read the article

• SQL SERVER – Database Dynamic Caching by Automatic SQL Server Performance Acceleration

  - by pinaldave

  My second look at SafePeak’s new version (2.1) revealed to me few additional interesting features. For those of you who hadn’t read my previous reviews SafePeak and not familiar with it, here is a quick brief: SafePeak is in business of accelerating performance of SQL Server applications, as well as their scalability, without making code changes to the applications or to the databases. SafePeak performs database dynamic caching, by caching in memory result sets of queries and stored procedures while keeping all those cache correct and up to date. Cached queries are retrieved from the SafePeak RAM in microsecond speed and not send to the SQL Server. The application gets much faster results (100-500 micro seconds), the load on the SQL Server is reduced (less CPU and IO) and the application or the infrastructure gets better scalability. SafePeak solution is hosted either within your cloud servers, hosted servers or your enterprise servers, as part of the application architecture. Connection of the application is done via change of connection strings or adding reroute line in the c:\windows\system32\drivers\etc\hosts file on all application servers. For those who would like to learn more on SafePeak architecture and how it works, I suggest to read this vendor’s webpage: SafePeak Architecture. More interesting new features in SafePeak 2.1 In my previous review of SafePeak new I covered the first 4 things I noticed in the new SafePeak (check out my article “SQLAuthority News – SafePeak Releases a Major Update: SafePeak version 2.1 for SQL Server Performance Acceleration”): Cache setup and fine-tuning – a critical part for getting good caching results Database templates Choosing which database to cache Monitoring and analysis options by SafePeak Since then I had a chance to play with SafePeak some more and here is what I found. 5. Analysis of SQL Performance (present and history): In SafePeak v.2.1 the tools for understanding of performance became more comprehensive. Every 15 minutes SafePeak creates and updates various performance statistics. Each query (or a procedure execute) that arrives to SafePeak gets a SQL pattern, and after it is used again there are statistics for such pattern. An important part of this product is that it understands the dependencies of every pattern (list of tables, views, user defined functions and procs). From this understanding SafePeak creates important analysis information on performance of every object: response time from the database, response time from SafePeak cache, average response time, percent of traffic and break down of behavior. One of the interesting things this behavior column shows is how often the object is actually pdated. The break down analysis allows knowing the above information for: queries and procedures, tables, views, databases and even instances level. The data is show now on all arriving queries, both read queries (that can be cached), but also any types of updates like DMLs, DDLs, DCLs, and even session settings queries. The stats are being updated every 15 minutes and SafePeak dashboard allows going back in time and investigating what happened within any time frame. 6. Logon trigger, for making sure nothing corrupts SafePeak cache data If you have an application with many parts, many servers many possible locations that can actually update the database, or the SQL Server is accessible to many DBAs or software engineers, each can access some database directly and do some changes without going thru SafePeak – this can create a potential corruption of the data stored in SafePeak cache. To make sure SafePeak cache is correct it needs to get all updates to arrive to SafePeak, and if a DBA will access the database directly and do some changes, for example, then SafePeak will simply not know about it and will not clean SafePeak cache. In the new version, SafePeak brought a new feature called “Logon Trigger” to solve the above challenge. By special click of a button SafePeak can deploy a special server logon trigger (with a CLR object) on your SQL Server that actually monitors all connections and informs SafePeak on any connection that is coming not from SafePeak. In SafePeak dashboard there is an interface that allows to control which logins can be ignored based on login names and IPs, while the rest will invoke cache cleanup of SafePeak and actually locks SafePeak cache until this connection will not be closed. Important to note, that this does not interrupt any logins, only informs SafePeak on such connection. On the Dashboard screen in SafePeak you will be able to see those connections and then decide what to do with them. Configuration of this feature in SafePeak dashboard can be done here: Settings -> SQL instances management -> click on instance -> Logon Trigger tab. Other features: 7. User management ability to grant permissions to someone without changing its configuration and only use SafePeak as performance analysis tool. 8. Better reports for analysis of performance using 15 minute resolution charts. 9. Caching of client cursors 10. Support for IPv6 Summary SafePeak is a great SQL Server performance acceleration solution for users who want immediate results for sites with performance, scalability and peak spikes challenges. Especially if your apps are packaged or 3rd party, since no code changes are done. SafePeak can significantly increase response times, by reducing network roundtrip to the database, decreasing CPU resource usage, eliminating I/O and storage access. SafePeak team provides a free fully functional trial www.safepeak.com/download and actually provides a one-on-one assistance during such trial. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: About Me, Pinal Dave, PostADay, SQL, SQL Authority, SQL Performance, SQL Query, SQL Server, SQL Tips and Tricks, SQL Utility, T SQL, Technology

  Read the article

• Fix Windows Computer Problems with Microsoft Fix it Center

  - by Matthew Guay

  Fixing computer problems can often be difficult, but Microsoft is aiming to make it as simple as a couple clicks with.  Here’s how you can easily fix computer problems with Microsoft’s new Fix it Center Beta. Last year Microsoft began offering small Fix it scripts that you could download and run to help solve common computer problems automatically.  These were added to some of the most visited Windows help pages, and helped fix problems with things such as printing errors and Aero glass support.  Now, the Fix it scripts have been bundled together with the Fix it Center, making fixing your computer even easier.  This free tool works great on all editions of Windows XP, Vista, and Windows 7. Note: The Fix it Center is currently in beta, so only run if you are comfortable running beta software. Getting Started Download the Fix it Center installer (link below), and install as normal. The installer will download the remaining components, and then finish the installation. In Windows XP, if you have not yet installed .NET 2.0, you may see the following prompt.  Click Yes to go to the download site, and once you’ve installed .NET 2.0, run the Fix it Center setup again. Also, the Fix it Center uses PowerShell to automate its fixes, but if it is not installed yet the installer will automatically download and install it. Find Fixes for Your PC Once Fix it Center is installed, you can personalize it for your computer.  Select Now, and the click Next. It will scan your computer for problems with known solutions, and will offer to go ahead and install these troubleshooters.  If you choose to not install them, you can always download them from within the Fix it Center at a later time. While those troubleshooters are downloading, you can create a Fix it account.  This will give you additional help and support, and let you review Fix it solutions for all your computers from an online dashboard.  You need a Windows Live ID to create an account. Also, choose whether or not to send information to Microsoft about your hardware and software problems. Get Problems Fixed Now that the Fix it Center is installed and has identified issues on your computer, it’s time to get the problems fixed.  Here’s the default front screen in Windows 7, showing all of the available fixes. And here’s the Fix it Center running in Windows XP. Select one of the Troubleshooters to see more information about it, and click Run to start it. You can choose to either detect problems and have them fixed automatically, or you can choose for the Fix it Center to show you the solutions and let you choose whether to apply them or not.  The defaults usually work good, and only take a couple minutes to apply the fixes, but you can select your own fixes if you’d rather be in control. It will scan your computer for known problems in this area, and then will show you the results.  Here, Fix it determined that startup programs may be causing performance issues.  Select Start System Configuration, and uncheck any of the programs you do not usually use. Once you’ve run a troubleshooter, you can see the issues it checked for and any problems it discovered. If you created the online account, you can also choose to view the details online.  This will show all of your computers with Fix it Center and the fixes you’ve run on them.   Conclusion Whether you’re a power user or new to computers, sometimes it’s best to just get your problems fixed and go on with life instead of digging through the registry, forums, and hacking your way to a solution.  Remember the service is still in beta and may not work perfectly or solve your issues every time. But it’s something cool and worth a look. Links Download Microsoft Fix it Center Beta Fix additional problems with Microsoft’s Fix it Center Online Similar Articles Productive Geek Tips Disable Windows Mobility Center in Windows 7 or VistaMake Outlook Faster by Disabling Unnecessary Add-InsUsing Netflix Watchnow in Windows Vista Media Center (Gmedia)Disable Security Center Popup Notifications in Windows VistaHow To Manage Action Center in Windows 7 TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Icelandic Volcano Webcams Open Multiple Links At One Go NachoFoto Searches Images in Real-time Office 2010 Product Guides Google Maps Place marks – Pizza, Guns or Strip Clubs Monitor Applications With Kiwi

  Read the article

• Parallelism in .NET – Part 1, Decomposition

  - by Reed

  The first step in designing any parallelized system is Decomposition.  Decomposition is nothing more than taking a problem space and breaking it into discrete parts.  When we want to work in parallel, we need to have at least two separate things that we are trying to run.  We do this by taking our problem and decomposing it into parts. There are two common abstractions that are useful when discussing parallel decomposition: Data Decomposition and Task Decomposition.  These two abstractions allow us to think about our problem in a way that helps leads us to correct decision making in terms of the algorithms we’ll use to parallelize our routine. To start, I will make a couple of minor points. I’d like to stress that Decomposition has nothing to do with specific algorithms or techniques.  It’s about how you approach and think about the problem, not how you solve the problem using a specific tool, technique, or library.  Decomposing the problem is about constructing the appropriate mental model: once this is done, you can choose the appropriate design and tools, which is a subject for future posts. Decomposition, being unrelated to tools or specific techniques, is not specific to .NET in any way.  This should be the first step to parallelizing a problem, and is valid using any framework, language, or toolset.  However, this gives us a starting point – without a proper understanding of decomposition, it is difficult to understand the proper usage of specific classes and tools within the .NET framework. Data Decomposition is often the simpler abstraction to use when trying to parallelize a routine.  In order to decompose our problem domain by data, we take our entire set of data and break it into smaller, discrete portions, or chunks.  We then work on each chunk in the data set in parallel. This is particularly useful if we can process each element of data independently of the rest of the data.  In a situation like this, there are some wonderfully simple techniques we can use to take advantage of our data.  By decomposing our domain by data, we can very simply parallelize our routines.  In general, we, as developers, should be always searching for data that can be decomposed. Finding data to decompose if fairly simple, in many instances.  Data decomposition is typically used with collections of data.  Any time you have a collection of items, and you’re going to perform work on or with each of the items, you potentially have a situation where parallelism can be exploited.  This is fairly easy to do in practice: look for iteration statements in your code, such as for and foreach. Granted, every for loop is not a candidate to be parallelized.  If the collection is being modified as it’s iterated, or the processing of elements depends on other elements, the iteration block may need to be processed in serial.  However, if this is not the case, data decomposition may be possible. Let’s look at one example of how we might use data decomposition.  Suppose we were working with an image, and we were applying a simple contrast stretching filter.  When we go to apply the filter, once we know the minimum and maximum values, we can apply this to each pixel independently of the other pixels.  This means that we can easily decompose this problem based off data – we will do the same operation, in parallel, on individual chunks of data (each pixel). Task Decomposition, on the other hand, is focused on the individual tasks that need to be performed instead of focusing on the data.  In order to decompose our problem domain by tasks, we need to think about our algorithm in terms of discrete operations, or tasks, which can then later be parallelized. Task decomposition, in practice, can be a bit more tricky than data decomposition.  Here, we need to look at what our algorithm actually does, and how it performs its actions.  Once we have all of the basic steps taken into account, we can try to analyze them and determine whether there are any constraints in terms of shared data or ordering.  There are no simple things to look for in terms of finding tasks we can decompose for parallelism; every algorithm is unique in terms of its tasks, so every algorithm will have unique opportunities for task decomposition. For example, say we want our software to perform some customized actions on startup, prior to showing our main screen.  Perhaps we want to check for proper licensing, notify the user if the license is not valid, and also check for updates to the program.  Once we verify the license, and that there are no updates, we’ll start normally.  In this case, we can decompose this problem into tasks – we have a few tasks, but there are at least two discrete, independent tasks (check licensing, check for updates) which we can perform in parallel.  Once those are completed, we will continue on with our other tasks. One final note – Data Decomposition and Task Decomposition are not mutually exclusive.  Often, you’ll mix the two approaches while trying to parallelize a single routine.  It’s possible to decompose your problem based off data, then further decompose the processing of each element of data based on tasks.  This just provides a framework for thinking about our algorithms, and for discussing the problem.

  Read the article

• WPF ListView as a DataGrid – Part 3

  - by psheriff

  I have had a lot of great feedback on the blog post about turning the ListView into a DataGrid by creating GridViewColumn objects on the fly. So, in the last 2 parts, I showed a couple of different methods for accomplishing this. Let’s now look at one more and that is use Reflection to extract the properties from a Product, Customer, or Employee object to create the columns. Yes, Reflection is a slower approach, but you could create the columns one time then cache the View object for re-use. Another potential drawback is you may have columns in your object that you do not wish to display on your ListView. But, just because so many people asked, here is how to accomplish this using Reflection.   Figure 1: Use Reflection to create GridViewColumns. Using Reflection to gather property names is actually quite simple. First you need to pass any type (Product, Customer, Employee, etc.) to a method like I did in my last two blog posts on this subject. Below is the method that I created in the WPFListViewCommon class that now uses reflection. C#public static GridView CreateGridViewColumns(Type anyType){  // Create the GridView  GridView gv = new GridView();  GridViewColumn gvc;   // Get the public properties.  PropertyInfo[] propInfo =          anyType.GetProperties(BindingFlags.Public |                                BindingFlags.Instance);   foreach (PropertyInfo item in propInfo)  {    gvc = new GridViewColumn();    gvc.DisplayMemberBinding = new Binding(item.Name);    gvc.Header = item.Name;    gvc.Width = Double.NaN;    gv.Columns.Add(gvc);  }   return gv;} VB.NETPublic Shared Function CreateGridViewColumns( _  ByVal anyType As Type) As GridView  ' Create the GridView   Dim gv As New GridView()  Dim gvc As GridViewColumn   ' Get the public properties.   Dim propInfo As PropertyInfo() = _    anyType.GetProperties(BindingFlags.Public Or _                          BindingFlags.Instance)   For Each item As PropertyInfo In propInfo    gvc = New GridViewColumn()    gvc.DisplayMemberBinding = New Binding(item.Name)    gvc.Header = item.Name    gvc.Width = [Double].NaN    gv.Columns.Add(gvc)  Next   Return gvEnd Function The key to using Relection is using the GetProperties method on the type you pass in. When you pass in a Product object as Type, you can now use the GetProperties method and specify, via flags, which properties you wish to return. In the code that I wrote, I am just retrieving the Public properties and only those that are Instance properties. I do not want any static/Shared properties or private properties. GetProperties returns an array of PropertyInfo objects. You can loop through this array and build your GridViewColumn objects by reading the Name property from the PropertyInfo object. Build the Product Screen To populate the ListView shown in Figure 1, you might write code like the following: C#private void CollectionSample(){  Product prod = new Product();   // Setup the GridView Columns  lstData.View =      WPFListViewCommon.CreateGridViewColumns(typeOf(Product));  lstData.DataContext = prod.GetProducts();} VB.NETPrivate Sub CollectionSample()  Dim prod As New Product()   ' Setup the GridView Columns  lstData.View = WPFListViewCommon.CreateGridViewColumns( _       GetType(Product))  lstData.DataContext = prod.GetProducts()End Sub All you need to do now is to pass in a Type object from your Product class that you can get by using the typeOf() function in C# or the GetType() function in VB. That’s all there is to it! Summary There are so many different ways to approach the same problem in programming. That is what makes programming so much fun! In this blog post I showed you how to create ListView columns on the fly using Reflection. This gives you a lot of flexibility without having to write extra code as was done previously. NOTE: You can download the complete sample code (in both VB and C#) at my website. http://www.pdsa.com/downloads. Choose Tips & Tricks, then "WPF ListView as a DataGrid – Part 3" from the drop-down. Good Luck with your Coding,Paul Sheriff ** SPECIAL OFFER FOR MY BLOG READERS **Visit http://www.pdsa.com/Event/Blog for a free eBook on "Fundamentals of N-Tier".  

  Read the article

• Add Background Images and Themes to Windows 7 Media Center

  - by DigitalGeekery

  Are you tired of the same Windows Media Center look and feel? Today we’ll show you how change the background and apply themes to WMC. Changing the Basic Color Scheme in WMC There are a couple of very basic color scheme options built in to Windows 7 Media Center. From the WMC Start Menu, select Settings on the Tasks strip and then select General. On the General settings screen select Visual and Sound Effects.   Under Color scheme you’ll find options for Windows Media Center standard, High contrast white, and High contrast black. Simply select a color scheme and click Save before exiting.   If you have used Media Center before you are familiar with the standard blue default theme. There is also the high contrast white. And, the high contrast black. Changing the Background Image with Media Center Studio Themes and custom backgrounds need to be added with the third-party software, Media Center Studio. You can find the download link at the end of this article. You can use your own high resolution photo, or download one from the Internet. For best results, you’ll want to find an image that meets or exceeds the resolution of your monitor. Also, using a darker colored background image is ideal as it should contrast better with the lighter colored text of the start menu. Once you’ve downloaded and installed Media Center Studio (link below), open the application select the Home tab on the ribbon and make sure you are on the Themes tab below. Click New. Select Biography from the left pane and type in a name for your new theme.   Next, click on the triangle next to Images to expand the list below. You’ll want to browse to Images > Common > Background. You should see a list of PNG image files located below Background. We will want to swap out the COMMON.ANIMATED.BACKGROUND.PNG and the COMMON.BACKGROUND.PNG images. Select COMMON.ANIMATED.BACKGROUND.PNG and click on the Browse button on the right.   Browse for your photo and click Open. Your selected image will appear on the left pane. Now, do the same for the COMMON.BACKGROUND.PNG. When finished, select the Home tab on the ribbon at the top and click Save.   Now switch to the Themes tab on the ribbon and the Themes tab below. (There are two Themes tabs which can be a bit confusing). Select your theme on the right pane and click Apply. Note: You won’t see the image backgrounds displayed. Your theme will be applied to Media Center. Close out of Media Center Studio and open Windows Media Center to check out your new background.   You can load multiple backgrounds images and switch them periodically as your mood changes. You might like to find a nice background featuring your favorite movie or TV show.   Perhaps you can even find a background of your favorite sports team.   Installing Themes with Media Center Studio Theme7MC has made available a small group of Media Center Studio Theme packs that are simple to download and install. You can find the download link below. Note: Before installing a theme, turn off any extenders and close Windows Media Center. Download any (or all) of the Theme7MC theme packages to your Media Center PC. Open Media Center Studio, select the Themes tab (the one at the top) and click Import Theme.   Browse for the theme you wish to import and click Open. Select your theme from the themes pane and click Apply. Media Center Studio will proceed to apply your theme. You should then see your new theme appear under Current theme on the left theme pane. Close out of Media Center Studio. Open Media Center and enjoy your new theme. Conclusion Media Center Studio runs on Windows 7 or Vista and gives users a solution for personalizing their Media Center backgrounds. It is a Beta application, however, so it still has a few bugs. Currently, there are only a handful of themes available at Themes7MC, but what they have is pretty slick. If you’d like to further customize the look of Media Center, check out our previous article on how to customize the Media Center start menu with Media Center Studio. Downloads Media Center Studio Theme7MC Similar Articles Productive Geek Tips Using Netflix Watchnow in Windows Vista Media Center (Gmedia)How To Rip a Music CD in Windows 7 Media CenterAutomatically Mount and View ISO files in Windows 7 Media CenterSchedule Updates for Windows Media CenterIntegrate Hulu Desktop and Windows Media Center in Windows 7 TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 VMware Workstation 7 Acronis Online Backup AceStock, a Tiny Desktop Quote Monitor Gmail Button Addon (Firefox) Hyperwords addon (Firefox) Backup Outlook 2010 Daily Motivator (Firefox) FetchMp3 Can Download Videos & Convert Them to Mp3

  Read the article

• Installing Visual Studio Team Foundation Server Service Pack 1

  - by Martin Hinshelwood

  As has become customary when the product team releases a new patch, SP or version I like to document the install. Although I had no errors on my main computer, my netbook did have problems. Although I am not ready to call it a Service Pack problem just yet! Update 2011-03-10 – Running the Team Foundation Server 2010 Service Pack 1 install a second time worked As per Brian's post I am installing the Team Foundation Server Service Pack first and indeed as this is a single server local deployment I need to install both. If I only install one it will leave the other product broken. This however does not affect you if you are running Visual Studio and Team Foundation Server on separate computers as is normal in a production deployment. Main workhorse I will be installing the service pack first on my main computer as I want to actually use it here. Figure: My main workhorse I will also be installing this on my netbook which is obviously of significantly lower spec, but I will do that one after. Although, as always I had my fingers crossed, I was not really worried. Figure: KB2182621 Compared to Visual Studio there are not really a lot of components to update. Figure: TFS 2010 and SQL 2008 are the main things to update There is no “web” installer for the Team Foundation Server 2010 Service Pack, but that is ok as most people will be installing it on a production server and will want to have everything local. I would have liked a Web installer, but the added complexity for the product team is not work the capability for a 500mb patch. Figure: There is currently no way to roll SP1 and RTM together Figure: No problems with the file verification, phew Figure: Although the install took a while, it progressed smoothly   Figure: I always like a success screen Well, as far as the install is concerned everything is OK, but what about TFS? Can I still connect and can I still administer it. Figure: Service Pack 1 is reflected correctly in the Administration Console I am confident that there are no major problems with TFS on my system and that it has been updated to SP1. I can do all of the things that I used before with ease, and with the new features detailed by Brian I think I will be happy. Netbook The great god Murphy has stuck, and my poor wee laptop spat the Team Foundation Server 2010 Service Pack 1 out so fast it hit me on the back of the head. That will teach me for not looking… Figure: “Installation did not succeed” I am pretty sure should not be all caps! On examining the file I found that everything worked, except the actual Team Foundation Server 2010 serving step. Action: System Requirement Checks... Action complete Action: Downloading and/or Verifying Items c:\757fe6efe9f065130d4838081911\VS10-KB2182621.msp: Verifying signature for VS10-KB2182621.msp c:\757fe6efe9f065130d4838081911\VS10-KB2182621.msp Signature verified successfully for VS10-KB2182621.msp c:\757fe6efe9f065130d4838081911\DACFramework_enu.msi: Verifying signature for DACFramework_enu.msi c:\757fe6efe9f065130d4838081911\DACFramework_enu.msi Signature verified successfully for DACFramework_enu.msi c:\757fe6efe9f065130d4838081911\DACProjectSystemSetup_enu.msi: Verifying signature for DACProjectSystemSetup_enu.msi Exists: evaluating Exists evaluated to false c:\757fe6efe9f065130d4838081911\DACProjectSystemSetup_enu.msi Signature verified successfully for DACProjectSystemSetup_enu.msi c:\757fe6efe9f065130d4838081911\TSqlLanguageService_enu.msi: Verifying signature for TSqlLanguageService_enu.msi c:\757fe6efe9f065130d4838081911\TSqlLanguageService_enu.msi Signature verified successfully for TSqlLanguageService_enu.msi c:\757fe6efe9f065130d4838081911\SharedManagementObjects_x86_enu.msi: Verifying signature for SharedManagementObjects_x86_enu.msi c:\757fe6efe9f065130d4838081911\SharedManagementObjects_x86_enu.msi Signature verified successfully for SharedManagementObjects_x86_enu.msi c:\757fe6efe9f065130d4838081911\SharedManagementObjects_amd64_enu.msi: Verifying signature for SharedManagementObjects_amd64_enu.msi c:\757fe6efe9f065130d4838081911\SharedManagementObjects_amd64_enu.msi Signature verified successfully for SharedManagementObjects_amd64_enu.msi c:\757fe6efe9f065130d4838081911\SQLSysClrTypes_x86_enu.msi: Verifying signature for SQLSysClrTypes_x86_enu.msi c:\757fe6efe9f065130d4838081911\SQLSysClrTypes_x86_enu.msi Signature verified successfully for SQLSysClrTypes_x86_enu.msi c:\757fe6efe9f065130d4838081911\SQLSysClrTypes_amd64_enu.msi: Verifying signature for SQLSysClrTypes_amd64_enu.msi c:\757fe6efe9f065130d4838081911\SQLSysClrTypes_amd64_enu.msi Signature verified successfully for SQLSysClrTypes_amd64_enu.msi c:\757fe6efe9f065130d4838081911\vcruntime\Vc_runtime_x86.cab: Verifying signature for vcruntime\Vc_runtime_x86.cab c:\757fe6efe9f065130d4838081911\vcruntime\Vc_runtime_x86.cab Signature verified successfully for vcruntime\Vc_runtime_x86.cab c:\757fe6efe9f065130d4838081911\vcruntime\Vc_runtime_x86.msi: Verifying signature for vcruntime\Vc_runtime_x86.msi c:\757fe6efe9f065130d4838081911\vcruntime\Vc_runtime_x86.msi Signature verified successfully for vcruntime\Vc_runtime_x86.msi c:\757fe6efe9f065130d4838081911\SetupUtility.exe: Verifying signature for SetupUtility.exe c:\757fe6efe9f065130d4838081911\SetupUtility.exe Signature verified successfully for SetupUtility.exe c:\757fe6efe9f065130d4838081911\vcruntime\Vc_runtime_x64.cab: Verifying signature for vcruntime\Vc_runtime_x64.cab c:\757fe6efe9f065130d4838081911\vcruntime\Vc_runtime_x64.cab Signature verified successfully for vcruntime\Vc_runtime_x64.cab c:\757fe6efe9f065130d4838081911\vcruntime\Vc_runtime_x64.msi: Verifying signature for vcruntime\Vc_runtime_x64.msi c:\757fe6efe9f065130d4838081911\vcruntime\Vc_runtime_x64.msi Signature verified successfully for vcruntime\Vc_runtime_x64.msi c:\757fe6efe9f065130d4838081911\NDP40-KB2468871.exe: Verifying signature for NDP40-KB2468871.exe c:\757fe6efe9f065130d4838081911\NDP40-KB2468871.exe Signature verified successfully for NDP40-KB2468871.exe Action complete Action: Performing actions on all Items Entering Function: BaseMspInstallerT >::PerformAction Action: Performing Install on MSP: c:\757fe6efe9f065130d4838081911\VS10-KB2182621.msp targetting Product: Microsoft Team Foundation Server 2010 - ENU Returning IDOK. INSTALLMESSAGE_ERROR [Error 1935.An error occurred during the installation of assembly 'Microsoft.TeamFoundation.WebAccess.WorkItemTracking,version="10.0.0.0",publicKeyToken="b03f5f7f11d50a3a",processorArchitecture="MSIL",fileVersion="10.0.40219.1",culture="neutral"'. Please refer to Help and Support for more information. HRESULT: 0x80070005. ] Returning IDOK. INSTALLMESSAGE_ERROR [Error 1712.One or more of the files required to restore your computer to its previous state could not be found. Restoration will not be possible.] Patch (c:\757fe6efe9f065130d4838081911\VS10-KB2182621.msp) Install failed on product (Microsoft Team Foundation Server 2010 - ENU). Msi Log: MSI returned 0x643 Entering Function: MspInstallerT >::Rollback Action Rollback changes PerformMsiOperation returned 0x643 PerformMsiOperation returned 0x643 OnFailureBehavior for this item is to Rollback. Action complete Final Result: Installation failed with error code: (0x80070643), "Fatal error during installation. " (Elapsed time: 0 00:14:09). Figure: Error log for Team Foundation Server 2010 install shows a failure As there is really no information in this log as to why the installation failed so I checked the event log on that box. Figure: There are hundreds of errors and it actually looks like there are more problems than a failed Service Pack I am going to just run it again and see if it was because the netbook was slow to catch on to the update. Hears hoping, but even if it fails, I would question the installation of Windows (PDC laptop original install) before I question the Service Pack Figure: Second run through was successful I don’t know if the laptop was just slow, or what… Did you get this error? If you did I will push this to the product team as a problem, but unless more people have this sort of error, I will just look to write this off as a corrupted install of Windows and reinstall.

  Read the article

• Change the User Interface Language in Ubuntu

  - by Matthew Guay

  Would you like to use your Ubuntu computer in another language?  Here’s how you can easily change your interface language in Ubuntu. Ubuntu’s default install only includes a couple languages, but it makes it easy to find and add a new interface language to your computer.  To get started, open the System menu, select Administration, and then click Language Support. Ubuntu may ask if you want to update or add components to your current default language when you first open the dialog.  Click Install to go ahead and install the additional components, or you can click Remind Me Later to wait as these will be installed automatically when you add a new language. Now we’re ready to find and add an interface language to Ubuntu.  Click Install / Remove Languages to add the language you want. Find the language you want in the list, and click the check box to install it.  Ubuntu will show you all the components it will install for the language; this often includes spellchecking files for OpenOffice as well.  Once you’ve made your selection, click Apply Changes to install your new language.  Make sure you’re connected to the internet, as Ubuntu will have to download the additional components you’ve selected. Enter your system password when prompted, and then Ubuntu will download the needed languages files and install them.   Back in the main Language & Text dialog, we’re now ready to set our new language as default.  Find your new language in the list, and then click and drag it to the top of the list. Notice that Thai is the first language listed, and English is the second.  This will make Thai the default language for menus and windows in this account.  The tooltip reminds us that this setting does not effect system settings like currency or date formats. To change these, select the Text Tab and pick your new language from the drop-down menu.  You can preview the changes in the bottom Example box. The changes we just made will only affect this user account; the login screen and startup will not be affected.  If you wish to change the language in the startup and login screens also, click Apply System-Wide in both dialogs.  Other user accounts will still retain their original language settings; if you wish to change them, you must do it from those accounts. Once you have your new language settings all set, you’ll need to log out of your account and log back in to see your new interface language.  When you re-login, Ubuntu may ask you if you want to update your user folders’ names to your new language.  For example, here Ubuntu is asking if we want to change our folders to their Thai equivalents.  If you wish to do so, click Update or its equivalents in your language. Now your interface will be almost completely translated into your new language.  As you can see here, applications with generic names are translated to Thai but ones with specific names like Shutter keep their original name. Even the help dialogs are translated, which makes it easy for users around to world to get started with Ubuntu.  Once again, you may notice some things that are still in English, but almost everything is translated. Adding a new interface language doesn’t add the new language to your keyboard, so you’ll still need to set that up.  Check out our article on adding languages to your keyboard to get this setup. If you wish to revert to your original language or switch to another new language, simply repeat the above steps, this time dragging your original or new language to the top instead of the one you chose previously. Conclusion Ubuntu has a large number of supported interface languages to make it user-friendly to people around the globe.  And since you can set the language for each user account, it’s easy for multi-lingual individuals to share the same computer. Or, if you’re using Windows, check out our article on how you can Change the User Interface Language in Vista or Windows 7, too! Similar Articles Productive Geek Tips Restart the Ubuntu Gnome User Interface QuicklyChange the User Interface Language in Vista or Windows 7Create a Samba User on UbuntuInstall Samba Server on UbuntuSee Which Groups Your Linux User Belongs To TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips VMware Workstation 7 Acronis Online Backup DVDFab 6 Revo Uninstaller Pro FetchMp3 Can Download Videos & Convert Them to Mp3 Use Flixtime To Create Video Slideshows Creating a Password Reset Disk in Windows Bypass Waiting Time On Customer Service Calls With Lucyphone MELTUP – "The Beginning Of US Currency Crisis And Hyperinflation" Enable or Disable the Task Manager Using TaskMgrED

  Read the article

• Convert Video and Remove Commercials in Windows 7 Media Center with MCEBuddy 1.1

  - by DigitalGeekery

  Today look at MCEBuddy for Windows 7 Media Center. This handy app automatically takes your recorded TV files and converts them to MP4, AVI, WMV, or MPEG format. It even has the option to cut out those annoying commercials during the conversion process. Installation and Configuration Download and extract MCE Buddy. (Download link below) Run the setup.exe file and take all the default settings.   Open MCEBuddy Configuration by going to Start > All Programs > MCEBuddy > MCEBuddy Configuration.   Video Paths The MCEBuddy application is comprised of a single window. The first step you’ll want to take is to define your Source and Destination paths. The “Source” will most likely be your Recorded TV directory. The Destination should NOT be the same as the Source folder. Note: The Recorded TV directory in Windows 7 Media Center will only display and play WTV & DVR-MS files. To watch the converted MP4, AVI, WMV, or MPEG files in Windows Media Center you’ll need to add them to your Video Library or Movie Library. Video Conversion Next, choose your preferred format for conversion from the “Convert to” drop down list. The default is MP4 with the H.264 codec. You’ll find a wide variety of formats. The first set of conversion options in the drop down list will resize the video to 720 pixels wide. The next two sections maintain the original size, and the final section is for a variety of portable devices.   Next, you’ll see a group of check boxes below the “Convert to” drop down list. The Commercial Skipping option will cut the commercials while converting the file. Sort By Series will create a sub-folder in your Destination folder for each TV show. Delete Original will delete the WTV file after conversion is complete. (This option is not recommended unless you are sure your files are converting properly and you no longer need the WTV file.) Start Minimized is ideal if you want to run MCEBuddy on Windows startup. Note: MCEBuddy installs and uses Comskip for commercial cutting by default. However, if you have ShowAnalyzer installed, it will use that application instead. Advanced Options To choose a specific time of day to perform the conversions, click the checkbox under the “Advanced Options,” and select the starting and ending times for conversion. For example, convert between 2 hours and 5 hours would be between 2 am and 5am. If you want MCEBuddy to constantly look for and immediately convert new recordings, leave the box unchecked.   The “Video age” option lets you choose a specific number of days to wait before performing the conversion. This can be useful if you want to watch the recordings first and delete those you don’t wish to convert. You can also choose the “Sub Directories” if you’d like MCEBuddy to convert files that are in a sub-folder in your “Source” directory. Second Conversion As you might expect, this option allows MCEBuddy to perform a second conversion of your file. This can be useful if you want to use your first conversion to create a higher quality MP4 or AVI file for playback on a larger screen, and a second one for a portable device such as Zune or iPhone. The same options from the first conversion are also available for the second. You’ll want to choose a separate Destination folder for the second conversion.   Start and Monitor Progress To start converting your video files, simply press the “Start” button at the bottom. You’ll be able to follow the progress in the “Current Activity” section. When all the video files have finished converting, or there are no current files to convert, MCEBuddy will display a “Started – Idle” status. Click “Stop” if you don’t want MCEBuddy to continue scanning for new files.   Conclusion MCEBuddy 1.1 will convert all WTV files in it’s source folder. If you want to pick and choose which recordings to convert, you may want to define a source folder different than the Recorded TV folder and then just copy or move the files you wish to convert into the new source folder. The conversion process does take a good bit of time. If you choose the commercial skipping and second conversion options it can take several hours to fully convert one TV recording. Overall, MCEBuddy makes a nice Media Center addition for those that want to save some space with smaller size files, convert Recorded TV files for their portable device, or automatically remove commercials. If you’re looking for a different method to skip commercials check out our post on how to skip commercials in Windows 7 Media Center. Download MCEBuddy 1.1 Similar Articles Productive Geek Tips Using Netflix Watchnow in Windows Vista Media Center (Gmedia)How To Skip Commercials in Windows 7 Media CenterHow To Convert Video Files to MP3 with VLCStartup Customizations for Media Center in Windows 7Add Folders to the Movie Library in Windows 7 Media Center TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional The Ultimate Excel Cheatsheet Convert the Quick Launch Bar into a Super Application Launcher Automate Tasks in Linux with Crontab Discover New Bundled Feeds in Google Reader Play Music in Chrome by Simply Dragging a File 15 Great Illustrations by Chow Hon Lam

  Read the article

• Create an iTunes Account without a credit card

  - by Matthew Guay

  iTunes Store offers a large variety of free content, but to download it you have to have an account. Usually you have to enter your credit card information to sign up, but here’s an easy way to get an iTunes account for free downloads without entering any payment info. Although iTunes Store is known for paid downloads of movies, music, and more, it also has a treasure trove of free media.  Some of it, including Podcasts and iTunes U educational content do not require an account to download.  However, any other free content, including free iPhone/iPod Touch apps and free or promotional music, videos, and TV Shows all require an account to download.  If you try to download a free movie or music download, you will be required to enter payment information. Even though your card will not be charged, it will be kept on file so you can be charged if you download a for-pay item.  However, if you only plan to download free items, it may be preferable to not have your account linked to a credit card. The following steps will get you an account without entering your credit card info. Getting Started First, make sure you have iTunes installed.  If you don’t already have it, download and install it (link below) with the default settings. Now open iTunes, and click the iTunes Store link on the left. Click the App Store link on the top of this page. Select a free app to download.  A simple way to do this is to scroll down to the Top Free Apps box on the right side, hover your mouse over the first item, and click on the Free button that appears when you hover over it. A popup will open asking you to sign in with your Apple ID.  Click “Create New Account”. Click Continue to create your account. Check the box to accept the Store Terms and Conditions, and click Continue.   Enter your email address, password, security question, and date of birth, and uncheck the boxes to get email if you don’t want it…then click Continue. Now, you will be asked to provide a payment method.  Notice now that the last option says None!  Click that bullet option… Then enter your billing address.  Simply enter your normal billing address, even though you are not entering a payment method.  Click Continue and your account will be created! If you get the Address Verification screen just verify your county and click Done. An email will be sent to you to verify your account… Click on the link in your email to verify your account, iTunes will launch and you’re prompted to enter in the Apple ID and Password you just created. Your account is successfully created! Now you can easily download any free media from iTunes.  Keep an eye on the Free on iTunes box on the bottom of the iTunes Store page for interesting downloads, or if you have an iPhone or iPod Touch, watch the popular Free downloads on the Apps page. And of course there is always great content on iTunes U to grab free as well. Purchasing for-pay media If you want to purchase an item on the iTunes store later, simply click on the item to download as normal.  Click Buy to proceed with the purchase. iTunes will prompt you that you need to enter payment information to complete the purchase.  Enter your Apple ID email and password, and then add the payment information as prompted.   Remove Payment Information from an iTunes Account If you’ve already entered payment information into your iTunes account, and would like to remove it, click Store in the top iTunes menu, and select View My Account. Enter your Apple ID email and password, and click View Account.   This will open your account information.  Click the Edit Payment Information button.   Now, click the None button to remove your payment information.  Click Done to save the changes. Your account will now prompt you to enter payment information if you try to make a purchase.  You could repeat these steps after making a purchase if you do not want iTunes to keep your payment info on file. Conclusion This is a great way to make an iTunes account without entering your credit card, or to remove your credit card info from your account.  Parents may especially enjoy this tip, as they can have an iTunes account on their kids computer or iPod Touch without worrying about them spending money with it. Links Download iTunes Similar Articles Productive Geek Tips Quick Tip: Switch Between Signatures in Outlook 2007 the Easy WayRedeem Pre-paid Zune Card Points for Zune Marketplace MediaCreate An Electronic Business Card In Outlook 2007Understanding Windows Vista Aero Glass RequirementsSpeed up Your Windows Vista Computer with ReadyBoost TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Draw Online using Harmony How to Browse Privately in Firefox Kill Processes Quickly with Process Assassin Need to Come Up with a Good Name? Try Wordoid StockFox puts a Lightweight Stock Ticker in your Statusbar Explore Google Public Data Visually

  Read the article

• Connecting to DB2 from SSIS

  - by Christopher House

  The project I'm currently working on involves moving various pieces of data from a legacy DB2 environment to some SQL Server and flat file locations.  Most of the data flows are real time, so they were a natural fit for the client's MQSeries on their iSeries servers and BizTalk to handle the messaging.  Some of the data flows, however, are daily batch type transmissions.  For the daily batch transmissions, it was decided that we'd use SSIS to pull the data direct from DB2 to either a SQL Server or flat file.  I'm not at all an SSIS guy, I've done a bit here and there, but mainly for situations were we needed to move data from a dev environment to QA, mostly informal stuff like that.  And, as much as I'm not an SSIS guy, I'm even less a DB2/iSeries guy.  Prior to this engagement, my knowledge of DB2 was limited to the fact that it's an IBM product and that it was probably a DBMS flatform (that's what the DB in DB2 means, right?).   One of my first goals when I came onto this project was to develop of POC SSIS package to pull some data from DB2 and dump it to a flat file.  It sounded like a pretty straight forward task.  As always, the devil is in the details.  Configuring the DB2 connection manager took a bit of trial and error.  As such, I thought I'd post my experiences here in hopes that they might save someone the efforts I went through.  That being said, please keep in mind, as I pointed out, I'm not at all a DB2 guy, so my terminology and explanations may not be 100% spot on. Before you get started, you need to figure out how you're going to connect to DB2.  From the research I did, it looks like there are a few options.  IBM has both an OLE DB and .Net data provider which can be found here.  I installed their client access tools and tried to use both the .Net and OLE DB providers but I received an error message from both when attempting to connect to the iSeries that indicated I needed a license for a product called DB2 Connect.  I inquired with one of my client's iSeries resources about a license for this product and it appears they didn't have one, so that meant the IBM drivers were out.  The other option that I found quite a bit of discussion around was Microsoft's OLE DB Provider for DB2.  This driver is part of the feature pack for SQL Server 2008 Enterprise Edition and can be downloaded here. As it turns out, I already had Microsoft's driver installed on my dev VM, which stuck me as odd since I hadn't installed it.  I discovered that the driver is installed with the BizTalk adapter pack for host systems, which was also installed on my VM.  However, it looks like the version used by the adapter pack is newer than the version provided in the SQL Server feature pack.   Once you get the driver installed, create a connection manager in your package just like you normally would and select the Microsoft OLE DB Provider for DB2 from the list of available drivers. After you select the driver, you'll need to enter in your host name, login credentials and initial catalog. A couple of things to note here.  First, the Initial catalog needs to be the same as your host name.  Not sure why that is, but trust me, it just does.  Second, for credentials, in my environment, we're using what the client's iSeries people refer to as "profiles".  I guess this is similar to SQL auth in the SQL Server world.  In other words, they've given me a username and password for connecting to DB, so I've entered it here. Next, click the Data Links button.  On the Data Links screen, enter your package collection on the first tab. Package collection is one of those DB2 concepts I'm still trying to figure out.  From the little bit I've read, packages are used to control SQL compilation and each DB2 connection needs one.  The package collection, I believe, controls where your package is created.  One of the iSeries folks I've been working with told me that I should always use QGPL for my package collection, as QGPL is "general purpose" and doesn't require any additional authority. Next click the ellipsis next to the Network drop-down.  Here you'll want to enter your host name again. Again, not sure why you need to do this, but trust me, my connection wouldn't work until I entered my hostname here. Finally, go to the Advanced tab, select your DBMS platform and check Process binary as character. My environment is DB2 on the iSeries and iSeries is the replacement for AS/400, so I selected DB2/AS400 for my platform.  Process binary as character was necessary to handle some of the DB2 data types.  I had a few columns that showed all their data as "System.Byte[]".  Checking Process binary as character resolved this. At this point, you should be good to go.  You can go back to the Connection tab on the Data Links dialog to perform a couple of tests to validate your configuration.  The Test Connection button is obvious, this just verifies you can connect to the host using the configuration data you've entered.  The Packages button will attempt to connect to the host and create the packages required to execute queries. This isn't meant to be a comprehensive look SSIS and DB2, these are just some of the notes I've come up with since I've started working with DB2 and SSIS.  I'm sure as I continue developing my packages, I'll find more quirks and will post them here.

  Read the article

• How to Collect Debug Info for Oracle SQL Developer

  - by thatjeffsmith

  In a perfect world, there would be no software bugs. Developers would always test their code. QA would find any scenarios and bugs the developers hadn’t already thought of. Regression tests would be complete and flawless. But alas, we can only afford to pay mere humans here, so we will have bugs from time to time. Or sometimes you are trying to do something the software wasn’t designed for, or perhaps your machine has exhausted it’s resources trying to build the un-buildable. When you run into problems, you will need help. Developers need your help so they can help you. Surprisingly enough, feedback like this isn’t very helpful: Your program isn’t working. How can I make it work? When you are ready to work with us on the SQL Developer OTN forum, you will most likely be asked to run SQL Developer and capture the output from the command console. In case you need help with this, ere’s a step-by-step process you can follow in Windows 7 (should work in XP too.) Open a windows command window Start – Run – CMD Once it’s open, click on the window icon and select ‘Defaults.’ Change the default buffer size to be something bigger, much bigger. Set the CMD window default buffer size HIGHER Note: you only need to do this once. Navigate to your SQL Developer Installation Folder Instead of running the ‘sqldeveloper.exe’ file in the root directory, we are going to go several sub-directories down. Find the ‘bin’ sub-directory and run the ‘sqldeveloper.exe’ there. When you do this, a CMD window will open, and then you’ll see the SQL Developer application load. The SQL Developer bin directory - run the tool from here and get a logging window Use SQL Developer as normal, until it ‘breaks’ or ‘hangs’ Now, you are ready to grab the nitty-gritty information that MIGHT tell the developer what is going wrong or happening in your scenario. Click back into the CMD window Send a Ctrl+Break or a Ctrl+Pause. If you on a newer laptop that doesn’t have this key, be sure to check the ‘Fn’ subset of keys. If you need to map the BREAK or PAUSE buttons, this article might help. You can also try the on-screen keyboard in windows – just type ‘OSK’ in your START – RUN prompt. Copy the logging information from the command window – all of it We need this information, help us get it! Open a case with Oracle Support or Start a Thread on the Forums Or email me. If you’re on my blog reading this, it’s the least I can do to help Now, before you hit ‘Send’ or ‘Post’ or ‘Submit’ – be sure to add a brief description of what you were doing in the application when you ran into the problem. Even if you were doing ‘nothing,’ let us know how many connections you had open, what windows were active, etc. The more you can tell us, the higher your odds go up to getting a quick fix or at least an answer as to what is happening. Also include the following information: The version of SQL Developer you are running The version of the JDK you are using The OS you are using The version of Oracle you are connected to Now, don’t be surprised if you get asked to upgrade to a supported configuration, say ‘version 3.1 and the 1.6 JDK.’ Supporting older versions of software is fun, and while we enjoy a challenge, it may be easier for you to upgrade your way out of the problem at hand.

  Read the article

• How to Use An Antivirus Boot Disc or USB Drive to Ensure Your Computer is Clean

  - by Chris Hoffman

  If your computer is infected with malware, running an antivirus within Windows may not be enough to remove it. If your computer has a rootkit, the malware may be able to hide itself from your antivirus software. This is where bootable antivirus solutions come in. They can clean malware from outside the infected Windows system, so the malware won’t be running and interfering with the clean-up process. The Problem With Cleaning Up Malware From Within Windows Standard antivirus software runs within Windows. If your computer is infected with malware, the antivirus software will have to do battle with the malware. Antivirus software will try to stop the malware and remove it, while the malware will attempt to defend itself and shut down the antivirus. For really nasty malware, your antivirus software may not be able to fully remove it from within Windows. Rootkits, a type of malware that hides itself, can be even trickier. A rootkit could load at boot time before other Windows components and prevent Windows from seeing it, hide its processes from the task manager, and even trick antivirus applications into believing that the rootkit isn’t running. The problem here is that the malware and antivirus are both running on the computer at the same time. The antivirus is attempting to fight the malware on its home turf — the malware can put up a fight. Why You Should Use an Antivirus Boot Disc Antivirus boot discs deal with this by approaching the malware from outside Windows. You boot your computer from a CD or USB drive containing the antivirus and it loads a specialized operating system from the disc. Even if your Windows installation is completely infected with malware, the special operating system won’t have any malware running within it. This means the antivirus program can work on the Windows installation from outside it. The malware won’t be running while the antivirus tries to remove it, so the antivirus can methodically locate and remove the harmful software without it interfering. Any rootkits won’t be able to set up the tricks they use at Windows boot time to hide themselves from the rest o the operating system. The antivirus will be able to see the rootkits and remove them. These tools are often referred to as “rescue disks.” They’re meant to be used when you need to rescue a hopelessly infected system. Bootable Antivirus Options As with any type of antivirus software, you have quite a few options. Many antivirus companies offer bootable antivirus systems based on their antivirus software. These tools are generally free, even when they’re offered by companies that specialized in paid antivirus solutions. Here are a few good options: avast! Rescue Disk – We like avast! for offering a capable free antivirus with good detection rates in independent tests. avast! now offers the ability to create an antivirus boot disc or USB drive. Just navigate to the Tools -> Rescue Disk option in the avast! desktop application to create bootable media. BitDefender Rescue CD – BitDefender always seems to receive good scores in independent tests, and the BitDefender Rescue CD offers the same antivirus engine in the form of a bootable disc. Kaspersky Rescue Disk – Kaspersky also receives good scores in independent tests and offers its own antivirus boot disc. These are just a handful of options. If you prefer another antivirus for some reason — Comodo, Norton, Avira, ESET, or almost any other antivirus product — you’ll probably find that it offers its own system rescue disk. How to Use an Antivirus Boot Disc Using an antivirus boot disc or USB drive is actually pretty simple. You’ll just need to find the antivirus boot disc you want to use and burn it to disc or install it on a USB drive. You can do this part on any computer, so you can create antivirus boot media on a clean computer and then take it to an infected computer. Insert the boot media into the infected computer and then reboot. The computer should boot from the removable media and load the secure antivirus environment. (If it doesn’t, you may need to change the boot order in your BIOS or UEFI firmware.) You can then follow the instructions on your screen to scan your Windows system for malware and remove it. No malware will be running in the background while you do this. Antivirus boot discs are useful because they allow you to detect and clean malware infections from outside an infected operating system. If the operating system is severely infected, it may not be possible to remove — or even detect — all the malware from within it. Image Credit: aussiegall on Flickr     

  Read the article

• SSAS Compare: an intern’s journey

  - by Red Gate Software BI Tools Team

  About a month ago, David mentioned an intern working in the BI Tools Team. That intern happens to be me! In five weeks’ time, I’ll start my second year of Computer Science at the University of Cambridge and be a full-time student again, but for the past eight weeks, I’ve been living a completely different life. As Jon mentioned before, the teams here at Red Gate are small and everyone (including the interns!) is responsible for the product as a whole. I’ve attended planning sessions, UX tests, daily meetings, and everything else a full-time member of the team would; I had as much say in where we would go next with the product as anyone; I was able to see that what I was doing was an important part of the product from the feedback we got in the UX tests. All these things almost made me forget that this is just an internship and not my full-time job. First steps at Red Gate Being based in Cambridge, Red Gate has many Cambridge university graduates working for them. They also hire some Cambridge undergraduates for internships each summer. With its popularity with university graduates and its great working environment, Red Gate has managed to build up a great reputation. When I thought of doing an internship here in Cambridge, Red Gate just seemed to be the obvious choice for my first real work experience. On my first day at Red Gate, David, the lead developer for SSAS Compare, helped me settle in and explained what I’d be doing. My task was to improve the user experience of displaying differences between MDX scripts by syntax highlighting, script formatting, and improving the difference identification in the first place. David suggested how I should approach the problem, but left all the details and design decisions to me. That was when I realised how much independence and responsibility I’d have. What I’ve done If you launch the latest version of SSAS Compare and drill down to an MDX script difference, you can see the changes that have been made. In earlier versions, you could only see the scripts in plain text on both sides — either in black or grey, depending on whether they were the same or not. However, you couldn’t see exactly where the scripts were different, which was especially annoying when the two scripts were large – as they often are. Furthermore, if parts of the two scripts were formatted differently, they seemed to be different but were actually the same, which caused even more confusion and made it difficult to see where the differences were. All these issues have been fixed now. The two scripts are automatically formatted by the tool so that if two things are syntactically equivalent, they look the same – including case differences in keywords! The actual difference is highlighted in grey, which makes them easy to spot. The difference identification has been improved as well, so two scripts aren’t identified as different if there’s just a difference in meaningless whitespace characters, or when you have “select” on one side and “SELECT” on the other. We also have syntax highlighting, which makes it easier to read the scripts. How I did it In order to do the formatting properly, we decided to parse the MDX scripts. After some investigation into parser builders, I decided to go with the GOLD Parser builder and the bsn-goldparser .NET engine. GOLD Parser builder provides a fairly nice GUI to write, build, and test grammar in. We also liked the idea of separating the grammar building from parsing a text. The bsn-goldparser is one of many .NET engines for GOLD, and although it doesn’t support the newest features of GOLD Parser, it has “the ability to map semantic action classes to terminals or reduction rules, so that a completely functional semantic AST can be created directly without intermediate token AST representation, and without the need for glue code.” That makes it much easier for us to change the implementation in our program when we change the grammar. As bsn-goldparser is open source, and I wanted some more features in it, I contributed two new features which have now been merged to the project. Unfortunately, there wasn’t an MDX grammar written for GOLD already, so I had to write it myself. I was referencing MSDN to get the formal grammar specification, but the specification was all over the place, so it wasn’t that easy to implement and find. We’re aware that we don’t yet fully support all valid MDX, so sometimes you’ll just see the MDX script difference displayed the old way. In that case, there is some grammar construct we don’t yet recognise. If you come across something SSAS Compare doesn’t recognise, we’d love to hear about it so we can add it to our grammar. When some MDX script gets parsed, a tree is produced. That tree can then be processed into a list of inlines which deal with the correct formatting and can be outputted to the screen. Doing all this has led me to many new technologies and projects I haven’t worked with before. This was my first experience with C# and Visual Studio, although I have done things in Java before. I have learnt how to unit test with NUnit, how to do dependency injection with Ninject, how to source-control code with SVN and Mercurial, how to build with TeamCity, how to use GOLD, and many other things. What’s coming next Sadly, my internship comes to an end this week, so there will be less development on MDX difference view for a while. But the team is going to work on marking the differences better and making it consistent with difference indication in the top part of comparison window, and will keep adding support for more MDX grammar so you can see the differences easily in every comparison you make. So long! And maybe I’ll see you next summer!

  Read the article

• Surface development: it&rsquo;s just like software development

  - by Dennis Vroegop

  Surface is magic. Everyone using it seems to think that way. And I have to be honest, after working for almost 2 years with the platform I still get that special feeling the moment I turn on the unit to do some more work. The whole user experience, the rich environment of the SDK, the touch, even the look and feel of the Surface environment is so much different from the stuff I’ve been working on all my career that I am still bewildered by it. But… and this is a big but.. in the end we’re still talking about a computer and that needs software to become useful. Deep down the magic of the Surface unit there is a PC somewhere, running Windows Vista and the .net framework 3.5. When you write that magic software that makes the platform come alive you’re still working with .net, WPF/XNA, C#, VB.Net and all those other tools and technologies you know so well. Sure, the whole user experience is different from what you’ve known. And the way of thinking about users, their interaction and the positioning of screen elements requires a whole new paradigm. And that takes time. It took me about half a year before I had the feeling I got it nailed down. But when that moment came (about 18 months ago…) I realized that everything I had learned so far on software development still is true when it comes to Surface. The last 6 months I have been working with some people with a different background to start a new company. The idea was that the new company would be focussing on Surface and Surface only. These people come from a marketing background and had some good ideas for some applications. And I have to admit: their ideas were good. Very good. Where it all fell down of course is that these ideas need to be implemented in a piece of software. And creating great software takes skilled developers and a lot of time and money. That’s where things went wrong: the marketing guys didn’t realize and didn’t want to realize that software development is a job that takes skill. You can’t just hire a bunch of developers and expect them to deliver the best sort of software, especially not when it comes to Surface. I tried to explain that yes, their User Interface in Photoshop looked great, but no: I couldn’t develop an application like that in a weeks time. Even worse: the while backend of the software (WCF for communications, SQL Server for the database, etc) would take a lot more time than the frontend. They didn’t understand. It took them a couple of days to drawn the UI in Photoshop so in Blend I should be able to build the software in about the same amount of time. Well, you and I know that it doesn’t work that way. Software is hard to write, and even harder to write well, and it takes skill and dedication. It’s not something you can do as fast as you can draw a mock up for a Surface application in Photohop. The same holds true for web applications of course. A lot of designers there fail to appreciate the hard work that goes into writing the plumbing for a good web app that can handle thousands of users. Although the UI is very important, it’s not all there is to it. And in Surface development this is the same. The UI should create the feeling of magic, but the software behind it is what makes it come alive. And that takes time. A lot of time. So brush of you skills and don’t throw them away if you start developing for Surface. Because projects (and colaborations) can fail there as hard as they can in any other area of software development. On a side note: we decided to stop the colaboration (something the other parties involved didn’t appreciate and were very angry about) and decided to hire a designer for the Surface projects. The focus is back where it belongs: on the software development we know so well and have been doing very well for 13 years. UI is just a part of the whole project and not the end product. So my company Detrio is still going strong when it comes to develivering Surface solutions but once again from a technological background, not a marketing background.

  Read the article

• Using CMS for App Configuration - Part 1, Deploying Umbraco

  - by Elton Stoneman

  Originally posted on: http://geekswithblogs.net/EltonStoneman/archive/2014/06/04/using-cms-for-app-configurationndashpart-1-deploy-umbraco.aspxSince my last post on using CMS for semi-static API content, How about a new platform for your next API… a CMS?, I’ve been using the idea for centralized app configuration, and this post is the first in a series that will walk through how to do that, step-by-step. The approach gives you a platform-independent, easily configurable way to specify your application configuration for different environments, with a built-in approval workflow, change auditing and the ability to easily rollback to previous settings. It’s like Azure Web and Worker Roles where you can specify settings that change at runtime, but it's not specific to Azure - you can use it for any app that needs changeable config, provided it can access the Internet. The series breaks down into four posts: Deploying Umbraco – the CMS that will store your configurable settings and the current values; Publishing your config – create a document type that encapsulates your settings and a template to expose them as JSON; Consuming your config – in .NET, a simple client that uses dynamic objects to access settings; Config lifecycle management – how to publish, audit, and rollback settings. Let’s get started. Deploying Umbraco There’s an Umbraco package on Azure Websites, so deploying your own instance is easy – but there are a couple of things to watch out for, so this step-by-step will put you in a good place. Create From Gallery The easiest way to get started is with an Azure subscription, navigate to add a new Website and then Create From Gallery. Under CMS, you’ll see an Umbraco package (currently at version 7.1.3): Configure Your App For high availability and scale, you’ll want your CMS on separate kit from anything else you have in Azure, so in the configuration of Umbraco I’d create a new SQL Azure database – which Umbraco will use to store all its content: You can use the free 20mb database option if you don’t have demanding NFRs, or if you’re just experimenting. You’ll need to specify a password for a SQL Server account which the Umbraco service will use, and changing from the default username umbracouser is probably wise. Specify Database Settings You can create a new database on an existing server if you have one, or create new. If you create a new server *do not* use the same username for the database server login as you used for the Umbraco account. If you do, the deployment will fail later. Think of this as the SQL Admin account that you can use for managing the db, the previous account was the service account Umbraco uses to connect. Make Tea If you have a fast kettle. It takes about two minutes for Azure to create and provision the website and the database. Install Umbraco So far we’ve deployed an empty instance of Umbraco using the Azure package, and now we need to browse to the site and complete installation. My Website was called my-app-config, so to complete installation I browse to http://my-app-config.azurewebsites.net:   Enter the credentials you want to use to login – this account will have full admin rights to the Umbraco instance. Note that between deploying your new Umbraco instance and completing installation in this step, anyone can browse to your website and complete the installation themselves with their own credentials, if they know the URL. Remote possibility, but it’s there. From this page *do not* click the big green Install button. If you do, Umbraco will configure itself with a local SQL Server CE database (.sdf file on the Web server), and ignore the SQL Azure database you’ve carefully provisioned and may be paying for. Instead, click on the Customize link and: Configure Your Database You need to enter your SQL Azure database details here, so you’ll have to get the server name from the Azure Management Console. You don’t need to explicitly grant access to your Umbraco website for the database though. Click Continue and you’ll be offered a “starter” website to install: If you don’t know Umbraco at all (but you are familiar with ASP.NET MVC) then a starter website is worthwhile to see how it all hangs together. But after a while you’ll have a bunch of artifacts in your CMS that you don’t want and you’ll have to work out which you can safely delete. So I’d click “No thanks, I do not want to install a starter website” and give yourself a clean Umbraco install. When it completes, the installation will log you in to the welcome screen for managing Umbraco – which you can access from http://my-app-config.azurewebsites.net/umbraco: That’s It Easy. Umbraco is installed, using a dedicated SQL Azure instance that you can separately scale, sync and backup, and ready for your content. In the next post, we’ll define what our app config looks like, and publish some settings for the dev environment.

  Read the article

• Aamir Khan’s Satyamev Jayate stirs a movement

  - by Gopinath

  Bollywood actor Aamir Khan is known for his dedication and hard work in inspiring millions of viewers though movies by discussing social problems and motivating people to solve them. His movie Rang De Basanthi seeded Indian anti-corruption movement, Tare Zameen Par touched the problems faced by few challenged kids and the latest movie 3 idiots exposed how education institutions in India are producing lakhs of Donkeys out of colleges every year. He extended his dedication of serving the society to small screen with the launch of reality TV show Satyamev Jayate. Before you start misjudging it as one of those non sense drama / entertaining reality shows, let me tell you that it is not a typical music, games, fight or dance reality show. Satyamev Jayate is all about the real people of India, their problems and how to tackle them.  This is not just a reality show, its movement to educate people about the social evils. Its been many years since I spent couple of hours  in front of TV as most of the programs are too cynical or does not add much value.  In my childhood I use to anxiously wait for Mahabarath or He-Man TV shows to start but after a two decades I waited anxiously for the start of Satyamev Jayate. The wait was worth and the 1 hours 30 minutes spent watching it meaningful. When was the last time you were so satisfied after watching a TV show and inspired to do something? I don’t remember. Today, the show focused on female foeticide and its impact. It showed women who were tortured and forced to abort female foetuses. On the show few brave women shared their experiences of giving birth to girl babies and rough times they are going through with their in-laws & husbands. The show not only focused on the problem but also on the root cause of the evil,  inspiring people working to tackle it and what every individual can do his part to solve it.  The best part of the show is,  its not a blame game. When there is a problem most of the people quickly get into identifying who is wrong and start blaming them instead of solve the actual problem.  Aamir did not blame anyone for female foeticide – neither the government who don’t impose strict rules, nor the doctors who abort girl babies to make money or the mother-in-laws & husbands who torcher girl baby mothers are blamed. He careful highlighted the problem, showed horrifying statistics and their impact on the future society and few inspiring people working to tackle the problem.  He touched heart and stirred a movement against the issue. First time ever I voted for a reality show through SMS and it’s for Satyamev Jayate. I’m proud to do so. Here are the few reactions of popular people, activists & media about the program @aamir_khan absolutely the best program I have seen on TV in recent past. Thanku for converting an idiot box into an inspirationsl medium — Kiran Bedi (@thekiranbedi) May 6, 2012 Satyamev Jayate proves tht TV 2 can b a tool of social change. — Shekhar Kapur (@shekharkapur) May 6, 2012 i absolutely loved #satyamevjayate. at least aamir is doing what all of us only talk about. — Harsha Bhogle (@bhogleharsha) May 6, 2012 Now Television will no longer be called an idiot box,the VISION of Television broadens up with#SatyamevJayate !!! — Madhur Bhandarkar (@mbhandarkar268) May 6, 2012 The Sunday 11am slot seems to have come back with a bang… #SatyamevJayate — atul kasbekar (@atulkasbekar) May 6, 2012   I was spellbound, says Prasoon Joshi – It’s a unique show. I was completely bowled over by it. It’s a never-done before concept Aamir Khan strikes the right chord with Satyamev Jayate – The format is quite crisp. Talking about the emotional connect, there are moments when your eyes well up with tears, but the various segments ensure there’s more content than emotional drama ‘Satyamev Jayate’ gutsy, sensible show: Viewers – From filmmakers to clinical psychologists to professors – everyone has given the thumbs up to Aamir Khan’s television show ‘Satyamev Jayate’, saying it is a gutsy, hard-hitting and sensible programme that strikes an emotional chord with the audiences. Aamir Khan’s TV debut ‘Satyamev Jayate’ takes Twitter by storm – The roads of the capital sported a deserted look around 11 am on Sunday morning, as everyone was hooked on to their TV sets. Did you watch the program? What is your opinion? I’m waiting for next 11 AM of next Sunday. Are you?

  Read the article

• CodePlex Daily Summary for Sunday, March 07, 2010

  CodePlex Daily Summary for Sunday, March 07, 2010New ProjectsAlgorithminator: Universal .NET algorithm visualizer, which helps you to illustrate any algorithm, written in any .NET language. Still in development.ALToolkit: Contains a set of handy .NET components/classes. Currently it contains: * A Numeric Text Box (an Extended NumericUpDown) * A Splash Screen base fo...Automaton Home: Automaton is a home automation software built with a n-Tier, MVVM pattern utilzing WCF, EF, WPF, Silverlight and XBAP.Developer Controls: Developer Controls contains various controls to help build applications that can script/write code.Dynamic Reference Manager: Dynamic Reference Manager is a set (more like a small group) of classes and attributes written in C# that allows any .NET program to reference othe...indiologic: Utilities of an IndioNeural Cryptography in F#: This project is my magistracy resulting work. It is intended to be an example of using neural networks in cryptography. Hashing functions are chose...Particle Filter Visualization: Particle Filter Visualization Program for the Intel Science and Engineering FairPólya: Efficient, immutable, polymorphic collections. .Net lacks them, we provide them*. * By we, we mean I; and by efficient, I mean hopefully so.project euler solutions from mhinze: mhinze project euler solutionsSilverlight 4 and WCF multi layer: Silverlight 4 and WCF multi layersqwarea: Project for a browser-based, minimalistic, massively multiplayer strategy game. Part of the "Génie logiciel et Cloud Computing" course of the ENS (...SuperSocket: SuperSocket, a socket application framework can build FTP/SMTP/POP server easilyToast (for ASP.NET MVC): Dynamic, developer & designer friendly content injection, compression and optimization for ASP.NET MVCNew ReleasesALToolkit: ALToolkit 1.0: Binary release of the libraries containing: NumericTextBox SplashScreen Based on the VB.NET code, but that doesn't really matter.Blacklist of Providers: 1.0-Milestone 1: Blacklist of Providers.Milestone 1In this development release implemented - Main interface (Work Item #5453) - Database (Work Item #5523)C# Linear Hash Table: Linear Hash Table b2: Now includes a default constructor, and will throw an exception if capacity is not set to a power of 2 or loadToMaintain is below 1.Composure: CassiniDev-Trunk-40745-VS2010.rc1.NET4: A simple port of the CassiniDev portable web server project for Visual Studio 2010 RC1 built against .NET 4.0. The WCF tests currently fail unless...Developer Controls: DevControls: These are the version 1.0 releases of these controls. Download the individually or all together (in a .zip file). More releases coming soon!Dynamic Reference Manager: DRM Alpha1: This is the first release. I'm calling it Alpha because I intend implementing other functions, but I do not intend changing the way current functio...ESB Toolkit Extensions: Tellago SOA ESB Extenstions v0.3: Windows Installer file that installs Library on a BizTalk ESB 2.0 system. This Install automatically configures the esb.config to use the new compo...GKO Libraries: GKO Libraries 0.1 Alpha: 0.1 AlphaHome Access Plus+: v3.0.3.0: Version 3.0.3.0 Release Change Log: Added Announcement Box Removed script files that aren't needed Fixed & issue in directory path Stylesheet...Icarus Scene Engine: Icarus Scene Engine 1.10.306.840: Icarus Professional, Icarus Player, the supporting software for Icarus Scene Engine, with some included samples, and the start of a tutorial (with ...mavjuz WndLpt: wndlpt-0.2.5: New: Response to 5 LPT inputs "test i 1" New: Reaction to 12 LPT outputs "test q 8" New: Reaction to all LPT pins "test pin 15" New: Syntax: ...Neural Cryptography in F#: Neural Cryptography 0.0.1: The most simple version of this project. It has a neural network that works just like logical AND and a possibility to recreate neural network from...Password Provider: 1.0.3: This release fixes a bug which caused the program to crash when double clicking on a generic item.RoTwee: RoTwee 6.2.0.0: New feature is as next. 16649 Add hashtag for tweet of tune.Now you can tweet your playing tune with hashtag.Visual Studio DSite: Picture Viewer (Visual C++ 2008): This example source code allows you to view any picture you want in the click of a button. All you got to do is click the button and browser via th...WatchersNET CKEditor™ Provider for DotNetNuke: CKEditor Provider 1.8.00: Whats New File Browser: Folders & Files View reworked File Browser: Folders & Files View reworked File Browser: Folders are displayed as TreeVi...WSDLGenerator: WSDLGenerator 0.0.0.4: - replaced CommonLibrary.dll by CommandLineParser.dll - added better support for custom complex typesMost Popular ProjectsMetaSharpSilverlight ToolkitASP.NET Ajax LibraryAll-In-One Code FrameworkWindows 7 USB/DVD Download Toolニコ生アラートWindows Double ExplorerVirtual Router - Wifi Hot Spot for Windows 7 / 2008 R2Caliburn: An Application Framework for WPF and SilverlightArkSwitchMost Active ProjectsUmbraco CMSRawrSDS: Scientific DataSet library and toolsBlogEngine.NETjQuery Library for SharePoint Web Servicespatterns & practices – Enterprise LibraryIonics Isapi Rewrite FilterFarseer Physics EngineFasterflect - A Fast and Simple Reflection APIFluent Assertions

  Read the article

• ASP.NET MVC HandleError Attribute

  - by Ben Griswold

  Last Wednesday, I took a whopping 15 minutes out of my day and added ELMAH (Error Logging Modules and Handlers) to my ASP.NET MVC application.  If you haven’t heard the news (I hadn’t until recently), ELMAH does a killer job of logging and reporting nearly all unhandled exceptions.  As for handled exceptions, I’ve been using NLog but since I was already playing with the ELMAH bits I thought I’d see if I couldn’t replace it. Atif Aziz provided a quick solution in his answer to a Stack Overflow question.  I’ll let you consult his answer to see how one can subclass the HandleErrorAttribute and override the OnException method in order to get the bits working.  I pretty much took rolled the recommended logic into my application and it worked like a charm.  Along the way, I did uncover a few HandleError fact to which I wasn’t already privy.  Most of my learning came from Steven Sanderson’s book, Pro ASP.NET MVC Framework.  I’ve flipped through a bunch of the book and spent time on specific sections.  It’s a really good read if you’re looking to pick up an ASP.NET MVC reference. Anyway, my notes are found a comments in the following code snippet.  I hope my notes clarify a few things for you too. public class LogAndHandleErrorAttribute : HandleErrorAttribute {     public override void OnException(ExceptionContext context)     {         // A word from our sponsors:         //      http://stackoverflow.com/questions/766610/how-to-get-elmah-to-work-with-asp-net-mvc-handleerror-attribute         //      and Pro ASP.NET MVC Framework by Steven Sanderson         //         // Invoke the base implementation first. This should mark context.ExceptionHandled = true         // which stops ASP.NET from producing a "yellow screen of death." This also sets the         // Http StatusCode to 500 (internal server error.)         //         // Assuming Custom Errors aren't off, the base implementation will trigger the application         // to ultimately render the "Error" view from one of the following locations:         //         //      1. ~/Views/Controller/Error.aspx         //      2. ~/Views/Controller/Error.ascx         //      3. ~/Views/Shared/Error.aspx         //      4. ~/Views/Shared/Error.ascx         //         // "Error" is the default view, however, a specific view may be provided as an Attribute property.         // A notable point is the Custom Errors defaultRedirect is not considered in the redirection plan.         base.OnException(context);           var e = context.Exception;                  // If the exception is unhandled, simply return and let Elmah handle the unhandled exception.         // Otherwise, try to use error signaling which involves the fully configured pipeline like logging,         // mailing, filtering and what have you). Failing that, see if the error should be filtered.         // If not, the error simply logged the exception.         if (!context.ExceptionHandled                || RaiseErrorSignal(e)                   || IsFiltered(context))                  return;           LogException(e); // FYI. Simple Elmah logging doesn't handle mail notifications.     }

  Read the article

• How to Access a Windows Desktop From Your Tablet or Phone

  - by Chris Hoffman

  iPads and Android tablets can’t run Windows apps locally, but they can access a Windows desktops remotely — even with a physical keyboard. In a pinch, the same tricks can be used to access a Windows desktop from a smartphone. Microsoft recently launched their own official Remote Desktop app for iOS and Android devices. Microsoft’s official apps are primarily useful for businesses — if you’re a typical home user, you’ll want to use a different remote desktop solution. Microsoft’s Remote Desktop App Microsoft now offers official Remote Desktop apps for iPad and iPhone as well as Android tablets and smartphones. The apps use Microsoft’s RDP protocol to connect to remote Windows systems. They’re essentially just new clients for the Remote Desktop feature that has been included in Windows for more than a decade. There are big problems with these apps if you’re an average home user. Microsoft’s Remote Desktop server is not available on standard or Home versions of Windows, only Professional and Enterprise editions. If you do have the appropriate edition of Windows, you’ll have to set up port-forwarding and a dynamic DNS service if you want to access your Windows desktop from outside your local network. You could also set up a VPN — either way you’ll need to do some footwork. This app is a gift to businesses who are already using Remote Desktop and enthusiasts who have the more expensive versions of Windows and don’t mind the configuration process. To set this up, follow our guide to setting up Remote Desktop for Internet access and connect using the Remote Desktop app instead of traditional Remote Desktop clients. TeamViewer If you have the standard edition of Windows or you just don’t want to mess around with port-forwarding and dynamic DNS configuration, you’ll want to skip Remote Desktop and use something else. We like TeamViewer for this. Just as it’s a great way to remotely troubleshoot your relatives’ computers, it’s also a great way to remotely access your own computer. It doesn’t have the same limitations Microsoft’s Remote Desktop system has — it’s completely free for personal use, runs on any edition of Windows, and is easy to set up. There’s no messing around with port-forwarding or dynamic DNS configuration. To get started, just download and run the TeamViewer program on your computer. You can get started with it immediately, but you’ll want to set up unattended access to connect remotely without using the codes displayed on your screen. To connect, just install the TeamViewer mobile app and log in with the details the TeamViewer window displays. TeamViewer also offers software that runs on Mac and Linux, so you can remote-control other types of computers from your tablet. Other Options Microsoft’s Remote Desktop app and TeamViewer aren’t the only options, of course. There are a variety of different apps and services built for this. Splashtop is another fairly popular remote desktop solution that some people report as being faster. Unfortunately, it’s not entirely free — the iPad and iPhone app costs $20 at regular price. To use it over the Internet, you’ll have to purchase an additional “Anywhere Access Pack.” If you’re frustrated with TeamViewer’s speed and you don’t mind spending money, you may want to try Splashtop instead. As always, you could use any VNC server along with a VNC client app. VNC is the do-it-yourself solution — it’s an open protocol. Unlike Microsoft’s RDP protocol, you can install a VNC server of your own, configure it how you like, and use any mobile VNC client app. This is more flexible because you can install a VNC server on any edition of Windows or even non-Windows operating systems, but it otherwise has all the same issues — you have to worry about port-forwarding, setting up dynamic DNS, and securing your VNC server. Keep an eye on Chrome Remote Desktop. Chrome already offers a built-in remote desktop feature that allows you to remotely control your PC from another Windows, Mac, Linux, or Chrome OS device. Google is rumored to be building an Android app for Chrome Remote Desktop, which would allow you to easily access a computer running Chrome from Android tablets. Google’s solution is much more user-friendly for average people than Microsoft’s Remote Desktop solution, which is clearly geared towards businesses. Chrome Remote Desktop just requires signing in with a Google account. Remote desktop solutions like Microsoft’s Remote Desktop app and TeamViewer are also available for Windows tablets. On Windows RT devices like the Surface RT and Surface 2, they allow you to use the full Windows desktop that’s unavailable on your tablet.     

  Read the article

• Play Your Favorite DOS Games in XP, Vista, and Windows 7

  - by Matthew Guay

  Want to take a trip down memory lane with old school DOS games?  D-Fend Reloaded makes it easy for you to play your favorite DOS games directly on XP, Vista, and Windows 7. D-Fend Reloaded is a great frontend for DOSBox, the popular DOS emulator.  It lets you install and run many DOS games and applications directly from its interface without ever touching a DOS prompt.  It works great on XP, Vista, and Windows 7 32 & 64-bit versions.   Getting Started Download D-Fend Reloaded (link below), and install with the default settings.  You don’t need to install DOSBox, as D-Fend Reloaded will automatically install all the components you need to run DOS games on Windows. D-Fend Reloaded can also be installed as a portable application, so you can run it from a flash drive on any Windows computer by selecting User defined installation. Then select Portable mode installation. Once D-Fend Reloaded is installed, you can go ahead and open the program. Then simply click “Accept all settings” to apply the default settings.   D-Fend is now ready to run all of your favorite DOS games. Installing DOS Games and Applications: To install a DOS game or application, simply drag-and-drop a zip file of the app into D-Fend Reloaded’s window.  D-Fend Reloaded will automatically extract the program… Then will ask you to name the application and choose where to store it — by default it uses the name of the DOS app. Now you’ll see a new entry for the app you just installed.  Simply double-click to run it.   D-Fend will remind you that you can switch out of fullscreen mode by pressing Alt+Enter, and can also close the DOS application by pressing Ctrl+F9.  Press Ok to run the program. Here we’re running Ms. PacPC, a remake of the classic game Ms. Pac-Man, in full-screen mode.  All features work automatically, including sound, and you never have to setup anything from DOS command line — it just works. Here it’s in windowed mode running on Windows 7. Please note that your color scheme may change to Windows Basic while running DOS applications. You can run DOS application just as easily.  Here’s Word 5.5 running in in DOSBox through D-Fend Reloaded… Game Packs: Want to quickly install many old DOS freeware and trial games?  D-Fend Reloaded offers several game packs that let you install dozens of DOS games with only four clicks…just download and run the game pack installer of your choice (link below). Now you’ve got a selection of DOS games to choose from. Here’s a group of poor lemmings walking around … in Windows 7. Conclusion D-Fend Reloaded gives you a great way to run your favorite DOS games and applications directly from XP, Vista, and Windows 7.  Give it a try, and relive your DOS days from the comfort of your Windows desktop. What were some of your favorite DOS games and applications? Leave a comment and let us know. Links Download D-Fend Reloaded Download DOS game packs for D-Fend Reloaded Download Ms. Pac-PC Similar Articles Productive Geek Tips Friday Fun: Get Your Mario OnFriday Fun: Go Retro with PacmanThursday’s Pre-Holiday Lazy Links RoundupFriday Fun: Five More Time Wasting Online GamesFriday Fun: Holiday Themed Games TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional The Growth of Citibank Quickly Switch between Tabs in IE Windows Media Player 12: Tweak Video & Sound with Playback Enhancements Own a cell phone, or does a cell phone own you? Make your Joomla & Drupal Sites Mobile with OSMOBI Integrate Twitter and Delicious and Make Life Easier

  Read the article

• Restore Your PC from Windows Home Server

  - by Mysticgeek

  If your computer crashes or you get a virus infection that makes it unrecoverable, doing a clean install can be a hassle, let alone getting your data back. If you’re backing up your computers to Windows Home Server, you can completely restore them to the last successful backup. Note: For this process to work you need to verify the PC you want to restore is connected to your network via Ethernet. If you have it connected wirelessly it won’t work. Restore a PC from Windows Home Server On the computer you want to restore, pop in the Windows Home Server Home Computer Restore disc and boot from it. If you don’t have one already made, you can easily make one following these instructions. We have also included the link to the restore disc below. Boot from the CD then select if your machine has 512MB or RAM or more. The disc will initialize… Then choose your language and keyboard settings. Hopefully if everything goes correctly, your network card will be detected and you can continue. However, if it doesn’t like in our example, click on the Show Details button. In the Detect Hardware screen click on the Install Drivers button. Now you will need to have a USB flash drive with the correct drivers on it. It has to be a flash drive or a floppy (if you happen to still have one of those) because you can’t take out the Restore CD. If you want to make sure you have the correct drivers on the USB flash drive, open the Windows Home Server Console on another computer on your network. In the Computers and Backup section right-click on the computer you want to restore and select View Backups. Select the backup you want to restore from and click the Open button in the Restore or view Files section. Now drag the entire contents of the folder named Windows Home Server Drivers for Restore to the USB flash drive. Back to the machine you’re trying to restore, insert the USB flash drive with the correct drivers and click the Scan button. Wait a few moments while the drivers are found then click Ok then Continue.   The Restore Computer Wizard starts up… Enter in your home server password and click Next. Select the computer you want to restore. If it isn’t selected by default you can pull it up from the dropdown list under Another Computer. Make certain you’re selecting the correct machine. Now select the backup you want to restore. In this example we only have one but chances are you’ll have several. If you have several backups to choose from, you might want to check out the details for them. Now you can select the disk from backup and and restore it to the destination volume. You might need to initialize a disk, change a drive letter, or other disk management tasks, if so, then click on Run Disk Manger. For example we want to change the destination drive letter to (C:).   After you’ve made all the changes to the destination disk you can continue with the restore process. If everything looks correct, confirm the restore configuration. If you need to make any changes at this point, you can still go back and make them. Now Windows Home Server will restore your drive. The amount of time it takes will vary depend on the amount of data you have to restore, network connection speed, and hardware. You are notified when the restore successfully completes. Click Finish and the PC will reboot and be restored and should be working correctly. All the updates, programs, and files will be back that were saved to the last successful backup. Anything you might have installed after that backup will be gone. If you have your computers set to backup every night, then hopefully it won’t be a big issue.   Conclusion Backing up the computers on your network to Windows Home Server is a valuable tool in your backup strategy. Sometimes you may only need to restore a couple files and we’ve covered how to restore them from backups on WHS and that works really well. If the unthinkable happens and you need to restore the entire computer, WHS makes that easy too.  Download Windows Home Server Home Computer Restore CD Similar Articles Productive Geek Tips Restore Files from Backups on Windows Home ServerCreate A Windows Home Server Home Computer Restore DiscGMedia Blog: Setting Up a Windows Home ServerShare Ubuntu Home Directories using SambaInstalling Windows Home Server TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Make your Joomla & Drupal Sites Mobile with OSMOBI Integrate Twitter and Delicious and Make Life Easier Design Your Web Pages Using the Golden Ratio Worldwide Growth of the Internet How to Find Your Mac Address Use My TextTools to Edit and Organize Text

  Read the article

• Using the “Settings.settings” functionalities in VB.NET can be tricky…

  - by Vincent Grondin

  Sometime you’re searching for something forever and when you find it, you realize it was right under your nose.  Maybe you were distracted by other things around… or maybe that thing right under your nose was so well hidden that it deserves a blog post…   That happened to me a few days ago while using the “Settings.settings” functionalities in my VB.NET application…  I thought it was a cool feature and I decided to use it…  So there I am adding new settings with “USER” scope and StringCollection as the data type, testing my application and everything works perfectly fine...  That was before I decided to modify the “Value” of one of my settings…  After changing the value of one of my settings, I start my application again and, to my surprise, my new values aren’t showing!  Hmmm… That’s odd…  My setting was a pretty long list of strings so I was rather angry at myself for not saving my work after I was done…  So I open up the Settings.setting in the designer and click the ellipsis symbol to enter my string collection again, but to my great pleasure (and disbelief) my strings are there!!!  Alright, you rock VB.NET!  You’ve just save me a bunch of typing time and I’m thinking it’s just a simple Visual Studio glitch…  I hit “Save” then “Save All” (just in case) and finally I rebuild everything and fire up my app once again.  Huh?  Where are my darn strings????????  Ok there’s a bug there…  I open up the app.config and my new strings are there!!!  Alright, let’s recap…  My new strings are in the app.config, they show correctly in the Settings.settings designer UI but they aren’t showing at runtime…  Hmmmm?  Let’s try something else…  Let’s start the application but outside Visual Studio this time… I fire up the exe and BAM!  My strings where there!  I “alt-tab” and hit “F5” and BOOM, no strings!  So it’s a bug in the Visual Studio environment… or could it be a FEATURE?  I must admit that I’m a little confused over what’s a bug and what’s a feature in Visual Studio… lol!   Finally I found out there’s a “cache” for your Visual Studio located here:  C:\Users\<your username>\AppData\Local\Microsoft\<your app name and a very weird temp ID>\<your app version>\user.config When using the “Settings.settings” with a setting of scope “user”, this file is out of sync with your app.config until you manually decide to update it… The button is right there… under your nose… at the top left corner of your screen in the settings designer…  See the big “Synchronize” button there?  Yep…  Now that’s user friendly isn’t it?  Oh, and wait until you see what it does when you click it…  It prompts you and basically says:  “Would you like your settings to start working inside Visual Studio now that you found out that I exist?” and of course the right answer is yes… or rather “OK”…  Unfortunately, you have to do this every time you edit a value… On the other hand, adding and removing settings seem to work flawlessly without having to click this magical button… go figure!  Oh and I almost forgot… this great “feature” is only available for VB.NET…  A project in C# using Settings.settings will work perfectly EVEN when editing values… Here’s a screenshot that shows this important button: Button Using other data types appears to work perfectly well…   Maybe it’s simply related to the StringCollection data type?  If you are a VB.NET programmer, you should pay attention to this when you plan on using the settings functionalities and your scope is “user” and your data type is StringCollection… Happy coding all!

  Read the article

• BizTalk host throttling &ndash; Singleton pattern and High database size

  - by S.E.R.

  Originally posted on: http://geekswithblogs.net/SERivas/archive/2013/06/30/biztalk-host-throttling-ndash-singleton-pattern-and-high-database-size.aspxI have worked for some days around the singleton pattern (for those unfamiliar with it, read this post by Victor Fehlberg) and have come across a few very interesting posts, among which one dealt with performance issues (here, also by Victor Fehlberg). Simply put: if you have an orchestration which implements the singleton pattern, then performances will continuously decrease as the orchestration receives and consumes messages, and that behavior is more obvious when the orchestration never ends (ie : it keeps looping and never terminates or completes). As I experienced the same kind of problem (actually I was alerted by SCOM, which told me that the host was being throttled because of High database size), I thought it would be a good idea to dig a little bit a see what happens deep inside BizTalk and thus understand the reasons for this behavior. NOTE: in this article, I will focus on this High database size throttling condition. I will try and work on the other conditions in some not too distant future… Test conditions The singleton orchestration For the purpose of this study, I have created the following orchestration, which is a very basic implementation of a singleton that piles up incoming messages, then does something else when a certain timeout has been reached without receiving another message: Throttling settings I have two distinct hosts : one that hosts the receive port (basic FILE port) : Ports_ReceiveHostone that hosts the orchestration : ProcessingHost In order to emphasize the throttling mechanism, I have modified the throttling settings for each of these hosts are as follows (all other parameters are set to the default value): [Throttling thresholds] Message count in database: 500 (default value : 50000) Evolution of performance counters when submitting messages Since we are investigating the High database size throttling condition, here are the performance counter that we should take a look at (all of them are in the BizTalk:Message Agent performance object): Database sizeHigh database sizeMessage delivery throttling stateMessage publishing throttling stateMessage delivery delay (ms)Message publishing delay (ms)Message delivery throttling state durationMessage publishing throttling state duration (If you are not used to Perfmon, I strongly recommend that you start using it right now: it is a wonderful tool that allows you to open the hood and see what is going on inside BizTalk – and other systems) Database size It is quite obvious that we will start by watching the database size and high database size counters, just to see when the first reaches the configured threshold (500) and when the second rings the alarm. NOTE : During this test I submitted 600 messages, one message at a time every 10ms to see the evolution of the counters we have previously selected. It might not show very well on this screenshot, but here is what happened: From 15:46:50 to 15:47:50, the database size for the Ports_ReceiveHost host (blue line) kept growing until it reached a maximum of 504.At 15:47:50, the high database size alert fires At first I was surprised by this result: why is it the database size of the receiving host that keeps growing since it is the processing host that piles up messages? Actually, it makes total sense. This counter measures the size of the database queue that is being filled by the host, not consumed. Therefore, the high database size alert is raised on the host that fills the queue: Ports_ReceiveHost. More information is available on the Public MPWiki page. Now, looking at the Message publishing throttling state for the receiving host (green line), we can see that a throttling condition has been reached at 15:47:50: We can also see that the Message publishing delay(ms) (blue line) has begun growing slowly from this point. All of this explains why performances keep decreasing when a singleton keeps processing new messages: the database size grows and when it has exceeded the Message count in database threshold, the host is throttled and the publishing delay keeps increasing. Digging further So, what happens to the database queue then? Is it flushed some day or does it keep growing and growing indefinitely? The real question being: will the host be throttled forever because of this singleton? To answer this question, I set the Message count in database threshold to 20 (this value is very low in order not to wait for too long, otherwise I certainly would have fallen asleep in front of my screen) and I submitted 30 messages. The test was started at 18:26. At 18:56 (ie : exactly 30min later) the throttling was stopped and the database size was divided by 2. 30 min later again, the database size had dropped to almost zero: I guess I’ll have to find some documentation and do some more testing before I sort this out! My guess is that some maintenance job is at work here, though I cannot tell which one Digging even further If we take a look at the Message delivery throttling state counter for the processing host, we can see that this host was also throttled during the submission of the 600 documents: The value for the counter was 1, meaning that Message delivery incoming rate for the host instance exceeds the Message delivery outgoing rate * the specified Rate overdrive factor (percent) value. We will see this another day… :) A last word Let’s end this article with a warning: DO NOT CHANGE THE THROTTLING SETTINGS LIGHTLY! The temptation can be great to just bypass throttling by setting very high values for each parameter (or zero in some cases, which simply disables throttling). Nevertheless, always keep in mind that this mechanism is here for a very good reason: prevent your BizTalk infrastructure from exploding!! So whatever you do with those settings, do a lot of testing and benchmarking!

  Read the article

• System locking up with suspicious messages about hard disk

  - by Chris Conway

  My system has started behaving strangely, intermittently locking up. I see messages like the following in syslog: Nov 18 22:22:00 claypool kernel: [ 3428.078156] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Nov 18 22:22:00 claypool kernel: [ 3428.078163] ata3.00: irq_stat 0x40000000 Nov 18 22:22:00 claypool kernel: [ 3428.078167] sr 2:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 Nov 18 22:22:00 claypool kernel: [ 3428.078182] ata3.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 Nov 18 22:22:00 claypool kernel: [ 3428.078184] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x1 (device error) Nov 18 22:22:00 claypool kernel: [ 3428.078188] ata3.00: status: { DRDY } Nov 18 22:22:00 claypool kernel: [ 3428.080887] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Nov 18 22:22:00 claypool kernel: [ 3428.080890] ata3.00: irq_stat 0x40000000 Nov 18 22:22:00 claypool kernel: [ 3428.080893] sr 2:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 Nov 18 22:22:00 claypool kernel: [ 3428.080905] ata3.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 Nov 18 22:22:00 claypool kernel: [ 3428.080906] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x1 (device error) Nov 18 22:22:00 claypool kernel: [ 3428.080910] ata3.00: status: { DRDY } And then this: Nov 18 23:13:56 claypool kernel: [ 6544.000798] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen Nov 18 23:13:56 claypool kernel: [ 6544.000804] ata1.00: failed command: FLUSH CACHE EXT Nov 18 23:13:56 claypool kernel: [ 6544.000814] ata1.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0 Nov 18 23:13:56 claypool kernel: [ 6544.000815] res 40/00:00:00:4f:c2/00:00:00:00:00/40 Emask 0x4 (timeout) Nov 18 23:13:56 claypool kernel: [ 6544.000819] ata1.00: status: { DRDY } Nov 18 23:13:56 claypool kernel: [ 6544.000825] ata1: hard resetting link Nov 18 23:14:01 claypool kernel: [ 6549.360324] ata1: link is slow to respond, please be patient (ready=0) Nov 18 23:14:06 claypool kernel: [ 6554.008091] ata1: COMRESET failed (errno=-16) Nov 18 23:14:06 claypool kernel: [ 6554.008103] ata1: hard resetting link Nov 18 23:14:11 claypool kernel: [ 6559.372246] ata1: link is slow to respond, please be patient (ready=0) Nov 18 23:14:16 claypool kernel: [ 6564.020228] ata1: COMRESET failed (errno=-16) Nov 18 23:14:16 claypool kernel: [ 6564.020235] ata1: hard resetting link Nov 18 23:14:21 claypool kernel: [ 6569.380109] ata1: link is slow to respond, please be patient (ready=0) Nov 18 23:14:31 claypool kernel: [ 6579.460243] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Nov 18 23:14:31 claypool kernel: [ 6579.486595] ata1.00: configured for UDMA/133 Nov 18 23:14:31 claypool kernel: [ 6579.486601] ata1.00: retrying FLUSH 0xea Emask 0x4 Nov 18 23:14:31 claypool kernel: [ 6579.486939] ata1.00: device reported invalid CHS sector 0 Nov 18 23:14:31 claypool kernel: [ 6579.486952] ata1: EH complete Nov 18 23:17:01 claypool CRON[3910]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Nov 18 23:17:01 claypool CRON[3908]: (CRON) error (grandchild #3910 failed with exit status 1) Nov 18 23:17:01 claypool postfix/sendmail[3925]: fatal: open /etc/postfix/main.cf: No such file or directory Nov 18 23:17:01 claypool CRON[3908]: (root) MAIL (mailed 1 byte of output; but got status 0x004b, #012) Nov 18 23:39:01 claypool CRON[4200]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -type f -cmin +$(/usr/lib/php5/maxlifetime) -print0 | xargs -n 200 -r -0 rm) There are no messages marked after 23:39. When I next tried to use the machine, it would not return from the screensaver (blank screen), nor switch to another terminal, and I had to hard reboot it. [UPDATE] The output of smartctl is here. I had trouble getting this, because / is being mounted read-only (?!), which prevents most applications from running. Also, it may not be related, but I have the following worrying messages in dmesg: [ 10.084596] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141 [ 10.098477] i2c i2c-0: nForce2 SMBus adapter at 0x600 [ 10.098483] ACPI: resource nForce2_smbus [io 0x0700-0x073f] conflicts with ACPI region SM00 [??? 0x00000700-0x0000073f flags 0x30] [ 10.098486] ACPI: This conflict may cause random problems and system instability [ 10.098487] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 10.098509] i2c i2c-1: nForce2 SMBus adapter at 0x700 [ 10.112570] Linux agpgart interface v0.103 [ 10.155329] atk: Resources not safely usable due to acpi_enforce_resources kernel parameter [ 10.161506] it87: Found IT8712F chip at 0x290, revision 8 [ 10.161517] it87: VID is disabled (pins used for GPIO) [ 10.161527] it87: in3 is VCC (+5V) [ 10.161528] it87: in7 is VCCH (+5V Stand-By) [ 10.161560] ACPI: resource it87 [io 0x0295-0x0296] conflicts with ACPI region ECRE [??? 0x00000290-0x000002af flags 0x45] [ 10.161562] ACPI: This conflict may cause random problems and system instability [ 10.161564] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [UPDATE 2] I swapped in a new SATA cable, per Phil's suggestion. The current output of smartctl is here, if it helps. [UPDATE 3] I don't think the cable fixed it. The system hasn't locked up yet, but my media player crashed a few minutes ago and I have the following in the syslog: Nov 20 16:07:17 claypool kernel: [ 2294.400033] ata1: link is slow to respond, please be patient (ready=0) Nov 20 16:07:47 claypool kernel: [ 2324.084581] ata1: COMRESET failed (errno=-16) Nov 20 16:07:47 claypool kernel: [ 2324.084588] ata1: limiting SATA link speed to 1.5 Gbps Nov 20 16:07:47 claypool kernel: [ 2324.084592] ata1: hard resetting link I get the following response from smartctl: $ sudo smartctl -a /dev/sda [sudo] password for chris: sudo: Can't open /var/lib/sudo/chris/0: Read-only file system smartctl 5.40 2010-03-16 r3077 [i686-pc-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Device: /0:0:0:0 Version: scsiModePageOffset: response length too short, resp_len=47 offset=50 bd_len=46 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.

  Read the article

< Previous Page | 597 598 599 600 601 602 603 604 605 606 607 608  | Next Page >