Search Results

Search found 16598 results on 664 pages for 'device center'.

Page 608/664 | < Previous Page | 604 605 606 607 608 609 610 611 612 613 614 615  | Next Page >

• Custom built machine has much higher power consumption than expected

  - by foraidt

  I built a machine according to the specs of a computer magazine (c't, Germany). According to the magazine, the power consumption should be at around 10W. I don't want to go into the specifics of the hardware but rather ask for general advice on where to look: I updated the BIOS/UEFI version to the latest version, installed all the recommended drivers and unplugged all hardware that's not necessary to boot into Windows. All that was left is the power supply, mainboard, cpu, cpu cooler and one SSD drive. But still I measured a power consumption of 50W, which is 40W more than it should be. I tried booting Linux Mint from a USB stick, so I don't think it's some Windows-related problem.. Where else could I look? Update 1 I dind't want the question to get closed for being too localized but if more details are necessary, here they are: The system is a desktop PC. The power consumption is measured using a Brennenstuhl PM 231 device, which was tested also by c't and they found it quite accurate. The PSU is an Enermax ETL300AWT, the mainboard Intel DH87RL (Socket 1150) and the CPU Intel G3220 (Haswell). Update 2 There is no online version of the article*. The most details I found can be read on its project page (in German, though...) (*)You can pay for downloadable PDFs, however. English translation of that project page Update 3 Regarding the sceptics: It may sound ridiculous but apparently 10W idle consumption is possible with Intel's Haswell architecture. As a kind of proof, there's an additional Blog article explicitly listing the steps needed to reduce the idle consumption to 10W. Additional hardware: I measured the consumption without the HDD, and as expected the usage dropped by around 10W. I have no chassis fans and the CPU fan is a "Scythe Mugen 4" model. It runs at around 600rpm so I think it won't draw much. When stripping off all my extra components I should be at 10W. But I'm not getting anywhere near that. I would be happy to see "just" 15W in the stripped down version but currently I'm not getting below 50W no matter which component I remove. As I see it this cannot be explained by the PSU being less efficient at lower consumption. I also waited half an hour or so (also checked that no Windows updates were running in the background) and the consumption dind't drop by more than a few watts.

  Read the article

• USB mouse connecting and disconnecting randomly

  - by Kalec

  I've bought an acer aspire 5742G about 2 months ago or so and it's been running great, but sometimes I used to hear the windows error beep but I had no idea what was causing it since the "bug" was automatically fixed so fast I couldn't even see an error message (also it kinda always happened when I was busy also, either in a game or while doing my homework). Later on my mouse would simply not work for 3-5 seconds then work again, I thought nothing of it at the time. I also had a problem where it only worked in one usb and one only. To move it I had to remove the battery, unplug the laptop and hold the power button for 2 minutes to reset the bios settings. Since today though it went nuts. Sometimes it disconnects / reconnects 12 times in 10 seconds and windows just keeps beeping till I unplug it, then it runs smooth for 5-6 minutes then it goes nuts again. Other times it seems like it skips (disconnects for a fraction of a second) other times just for 2-3 seconds. But this is incredibly frustrating. Sometimes the power just goes down (the laser turns off) and well that at least I would understand but this is a rare occurrence. Now I know the usb ports work since I have a lot of other devices connected and I tried the mouse on a room m8's laptop so the mouse also works. My only conclusion is that it's an operating system / settings bug and / or problem (I have tried the mouse in all ports by the way). All drivers and bios are up to date (maybe except mouse but I can't seem to update that and the mouse has no name, just a serial number which helps with nothing. Still it worked till today and nothing should have changed any way). I have made sure windows can't shut it down to save power (in device management). Also I tried to delete the drivers and re-install them, rebooting and the power button trick but nothing. Most I have done is get rid of the 12 disconnects / reconnects every 10 seconds :) but that's all :( I would buy a new one but I'm afraid it might do the same thing. ****EDIT****** Tried the mouse again at a friend but now it didn't even install it's software nor did the update work. Think I'll just buy a new one but I'd still like a suggestion at least so I'll leave this open #### EDIT 2 Now it works again, I can't explain this. Still thinking of getting a new one though

  Read the article

• How to know the source of certain TCP traffic on AIX

  - by A.Rashad

  We have two AIX boxes, one for production system and another for testing. both systems are running ATM machine switches, where the ATM device is connected via TCP socket. we had an issue on production system where the machine would power off or get disconnected but the netstat -na | grep <IP of machine > would still mention that the socket is up when simulated that case on the UAT environment, the problem did not happen, where the socket would terminate in 3 to 5 minutes. when sniffed on the traffic between the machine and ATM we found that no traffic takes place on production while there is some sort of heartbeat on UAT. but it is not initiated by the application. $>tcpdump | grep -v "10.2.2.71" | grep -v "HSRP" | grep "10.3.1.30" tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on en6, link-type 1, capture size 96 bytes 09:08:13.323421 IP server073.afs3-callback > 10.3.1.30.impera: . 278204201:278204202(1) ack 3307884029 win 164 09:08:13.335334 IP 10.3.1.30.impera > server073.afs3-callback: . ack 1 win 64180 09:08:23.425771 IP 10.3.1.30.impera > server073.afs3-callback: . 1:2(1) ack 1 win 64180 09:08:23.425789 IP server073.afs3-callback > 10.3.1.30.impera: . ack 2 win 65535 09:09:13.628985 IP server073.afs3-callback > 10.3.1.30.impera: . 0:1(1) ack 1 win 164 09:09:13.633900 IP 10.3.1.30.impera > server073.afs3-callback: . ack 1 win 64180 09:09:23.373634 IP 10.3.1.30.impera > server073.afs3-callback: . 1:2(1) ack 1 win 64180 09:09:23.373647 IP server073.afs3-callback > 10.3.1.30.impera: . ack 2 win 65535 while on production, that traffic is not there. we want to know where this traffic is initiated from to implement on production to sense disconnection our comms parameters are: tcp_keepcnt = 2 tcp_keepidle = 100 tcp_keepinit = 150 tcp_keepintvl = 150 tcp_finwait2 = 1200 can anyone help?

  Read the article

• Proper Imaging Procedures to Restore and Deploy Image with Separate System Reserved Partition

  - by alharaka

  UPDATE: As per my experience here, no one responded. If I do not hear back from TechNet forum members about it, I will post a bounty here, if it makes a difference. I have banged my head against a wall for what seems like all week. I am going to explain my simple procedure, and how none of it, absolutely none, seems to work afterword despite few alternatives and everyone on the internet telling assuming this is how to do it. Diskpart Commands to Create FS Structure REM Select the disk targeted for deployment. REM REM NOTE: Usually disk 0, but drive failure can make it external USB REM media. This will erase the drive regardless! select disk 0 REM Remove previous formatting. clean REM Create System Reserved partition bootloader and files. create partition primary size=100 REM Format the volume format fs=ntfs label="System Reserved" quick override noerr REM Assign the System Reserved partition the D: mount for now assign letter=C REM The main system partition, size not specified to occupy whole drive. create partition primary REM Format the volume format fs=ntfs quick override noerr REM Assign the OS partition the D: mount for now assign letter=D REM Make this the active/bootable partition. sel disk 0 sel partition 1 active REM Close out the diskpart session. exit Now, I thought this was madness, but it turns out the System Reserved partition and standard "System Partition" (C:, commonly both the boot and system volumes where you find the Windows directory AND the bootmgr/ntldr hardware files, this is where Windows 7 diverges) as mounted in the Windows PE session where I run these commands do not matter. See reference here. Since this needs to be BitLocker-ready, enter this crappy System Reserved partition that is separate 100MB of awesome that goes before the regular boot volume. I do this, then I proceed to the next step. Deploy System Reserved and Normal System Images REM C is still the "System Reserved Partition", and the image is just like it sounds. imagex /apply G:\images\systemreserved.wim 1 C: REM D is now what will be the C: system partition on reboot, supposedly. imagex /apply G:\images\testimage.wim 1 D: Reboot the system Now, the images I just captured should look good. This is not even sysprepped, but reapplying the same fscking image I prepared on the same reference workstation hours before. Problem is I get 0xc000000e could not detect the accessible boot device \Windows\system32\winload.exe or different kinds of nonsense revolving around being able to find the boot volume with all the right files. I try different variations of things, now none of them work. I tried repairs with bcdboot, with a fresh System Reserved partition or not, bootrec, and maually editing the damn BCD store with bcdedit. I tried finalizing the above process with and without bootsect /nt60 C: /force. I need to wrap up and automate this procedure. What am I doing wrong that does not make the image happy, but really just miserable.

  Read the article

• Problems migrating an EBS backed instance over AWS Regions

  - by gshankar

  Note: I asked this question on the EC2 forums too but haven't received any love there. Hopefully the ServerFault community will be more awesome. The new AWS Sydney region opening up is something that we've been waiting for for a long time but I'm having a lot of trouble migrating our instances over from N. California. I managed to migrate 1 instance over using CloudyScripts to move a snapshot and then firing up a new instance in the Sydney region. This was a very new instance so both the source and destination were running on a Ubuntu 12.04 LTS server and I had no issues there. However, the rest of our instances are all Ubuntu 10.04 LTS and with these, I'm having a lot of problems. I've tried following: 1- following the AWS whitepaper on moving instances which was given to us at the recent Customer Appreciation Day in Sydney where the new region was launched. The problem with this approach was with the last step (Step 19) here you register the image: ec2-register -s snap-0f62ec3f -n "Wombat" -d "migrated Wombat" --region ap-southeast-2 -a x86_64 --kernel aki-937e2ed6 --block-device-mapping "/dev/sdk=ephemeral0" I keep getting this error: Client.InvalidAMIID.NotFound: The AMI ID 'ami-937e2ed6' does not exist which I think is due to the kernel_id not existing in the Sydney region? 2- Using CloudyScripts to move a snapshot and then creating a new volume and attaching to a new instance in Sydney This results in the instance just hanging on boot and failing the status checks. I can't SSH in or look at the server log I suspect that my issue is with finding the right kernel_id for the volume in the new region. However I can't seem to work out how to go about finding this kernel_id, the ones I've tried (from the original instance) don't result in the Client.InvalidAMIID.NotFound: The AMI ID 'ami-937e2ed6' error and any other kernel_id just won't boot. I've tried both 12.04 and 10.04 versions of Ubuntu. Nothing seems to work, I've been banging my head against a wall for a while now, please help! New (broken) instance i-a1acda9b ami-9b8611a1 aki-31990e0b Source instance i-08a6664e ami-b37e2ef6 aki-937e2ed6 p.s. I also tried following this guide on updating my Ubuntu LTS version to 12.04 before doing the migration but it didn't seem to work either, still getting stuck on updating the kernel_id http://ubuntu-smoser.blogspot.com.au/2010/04/upgrading-ebs-instance.html

  Read the article

• windows server 2008 r2 remote desktop issue with roaming clients

  - by Patrick D'Haese

  I have the following situation : a Dell windows server 2008 R2 computer, with remote desktop services installed. I have installed a java application making use of a PostgreSql database, and made this application available for clients using RDP. Clients are standard Win XP pc's and Psion Neo handheld devices running Windows CE 5 Pro. The application works fine for clients on standard XP pc's connected directly via cat 5E Ethernet cable to a Dell Powerconnect 2816 switch. The Psion Neo clients connect wireless to the network via Motorola AP6532 access points. These access points are connected via a POE adapter to the same switch as the XP pc's. The Psion devices can connect without any problem and very quickly to the server and to the application using RDP. So far, so good. When the Psion devices move around in the warehouse, and they roam from one access point to the other, the RDP session on the client freezes for approx 1 minute, and then it automatically resumes the session. This freezing is very annoying for the users. Can anyone help in solving this issue? Update (August 9) : After re-installing the access points we have a working situation, but only when connecting to the RDP host : * via a Win Xp SP3 laptop * via a Symbol MC9190 Win CE 6 mobile device When roaming we notice a small hick-up less then 1 second, what is very acceptable. With the Psion NEO it's still not working, when roaming the screen freezes from 2 to 30 seconds. The RDP client on the win xp sp3 laptop and the symbol mc9190 is version 6.0. The RDP client on the neo is version 5.2. I have changed the security layer on the RDP host to RDP security layer (based on forums on the internet), because older RDP clients seem to have issues with the RDP 7.1 protocol on the Win server 2088 R2. Psion adviced us to do some network logging activity on the different devices. We made this logging via wireshark, and based on this the conclusion of Psion is that the server fails in handling tcp-requests. Can anyone give me a second opinion by analysing the wireshark loggings. Thanks in advance. Regards Patrick

  Read the article

• Encoding multiple video streams with a single avconv invocation

  - by automatthias

  I played with avconv on Ubuntu and I'm now able to e.g. record the desktop with sound from a soundcard. One thing I wanted to do was recording two video inputs at the same time, for instance the desktop and from the webcam. I thought about doing something like this: avconv \ -f alsa \ -i default \ -acodec flac \ -f video4linux2 \ -r 6 \ -i /dev/video0 \ -f x11grab \ -i :0.0 \ out.mkv My thinking was that if you define multiple video inputs, and the .mkv format can handle multiple video streams, avconv will encode 2 video streams and 1 audio stream into one file. But this isn't what happens: avconv version 0.8.4-6:0.8.4-0ubuntu0.12.10.1, Copyright (c) 2000-2012 the Libav developers built on Nov 6 2012 16:51:11 with gcc 4.7.2 [alsa @ 0x1091bc0] capture with some ALSA plugins, especially dsnoop, may hang. [alsa @ 0x1091bc0] Estimating duration from bitrate, this may be inaccurate Input #0, alsa, from 'default': Duration: N/A, start: 1354364317.020350, bitrate: N/A Stream #0.0: Audio: pcm_s16le, 48000 Hz, 2 channels, s16, 1536 kb/s [video4linux2 @ 0x10923e0] Estimating duration from bitrate, this may be inaccurate Input #1, video4linux2, from '/dev/video0': Duration: N/A, start: 100607.724745, bitrate: 29491 kb/s Stream #1.0: Video: rawvideo, yuyv422, 640x480, 29491 kb/s, 6 tbr, 1000k tbn, 6 tbc [x11grab @ 0x107b2a0] device: :0.0+83,87 -> display: :0.0 x: 83 y: 87 width: 854 height: 480 [x11grab @ 0x107b2a0] shared memory extension found [x11grab @ 0x107b2a0] Estimating duration from bitrate, this may be inaccurate Input #2, x11grab, from ':0.0+83,87': Duration: N/A, start: 1354364318.488382, bitrate: 196761 kb/s Stream #2.0: Video: rawvideo, bgra, 854x480, 196761 kb/s, 15 tbr, 1000k tbn, 15 tbc Incompatible pixel format 'bgra' for codec 'mpeg4', auto-selecting format 'yuv420p' [buffer @ 0x107fcc0] w:854 h:480 pixfmt:bgra [avsink @ 0x10bdf00] auto-inserting filter 'auto-inserted scaler 0' between the filter 'src' and the filter 'out' [scale @ 0x10dc680] w:854 h:480 fmt:bgra -> w:854 h:480 fmt:yuv420p flags:0x4 Output #0, matroska, to '.../out.mkv': Metadata: encoder : Lavf53.21.0 Stream #0.0: Video: mpeg4, yuv420p, 854x480, q=2-31, 4000 kb/s, 1k tbn, 15 tbc Stream #0.1: Audio: libvorbis, 48000 Hz, 2 channels, s16 Stream mapping: Stream #2:0 -> #0:0 (rawvideo -> mpeg4) Stream #0:0 -> #0:1 (pcm_s16le -> libvorbis) Press ctrl-c to stop encoding [mpeg4 @ 0x10bd800] rc buffer underflow ^Cframe= 160 fps= 15 q=2.0 Lsize= 3414kB time=10.66 bitrate=2623.0kbits/s video:3273kB audio:131kB global headers:4kB muxing overhead 0.165600% Received signal 2: terminating. I'm not sure if it's the question of mapping (some -map options to add?) or that avconv just can't encode more than 1 video stream at one time. So is it an actual avconv limitation, or a limitation of the available containers, or me simply not finding the right combination of command line options?

  Read the article

• ASA and cisco vs NSA sonic firewall

  - by Lbaker101

  Currently I’m trying to structure our network to fully support and be redundant with BGP/Multi homing. Our current company size is 40 employees but the major part of that is our Development department. We are a software company and continued connection to the internet is a requirement as 90% of work stops when the net goes down. The only thing hosted on site (that needs to remain up) is our exchange server. Right now i'm faced with 2 different directions and was wondering if I could get your opinions on this. We will have 2 ISPs that are both 20meg up/down and dedicated fiber (so 40megs combined). This is handed off as an Ethernet cable into our server room. ISP#1 first digital ISP#2 CenturyLink we currently have 2x ASA5505s but the 2nd one is not in use. It was there to be a failover and it just needs the security+ license to be matched with the primary device. But this depends on the network structure. I have been looking into the hardware that would be required to be fully redundant and I found that we will either of the following. 2x Cisco 2921+ series routers with failover licenses. They will go in front of the ASAs and either connects in a failover state or 1 ISP into each of the 2921 series routers and then 1 line into each of the ASAs (thus all 4 hardware components will be used actively). So 2x Cisco 2921+ series routers 2x Cisco ASA5505 firewalls The other route 2x SonicWalls NSA2400MX series. 1 primary and the secondary will be in a failover state. This will remove the ASAs from the network and be about 2k cheaper than the cisco route. This also brings down the points of failure because it’s just the 2x sonicwalls It will also allow us to scale all the way up to 200-400 users (depending on their configuration). This also makes so the Sonic walls. So the real question is with the added functionality ect of the sonicwall is there a point in paying so much more to stay the cisco route? Thanks!

  Read the article

• Ubuntu Lucid: Erratic screen behaviour after boot

  - by fgysin

  In short: about 50% of the time I have a screwed up monitor setup after reboot. About 50% it is totally correct. Now the longer version: I updated my machine from 9.04 to 10.04 (via 9.10). At first I run into some monitor problems (I have a 3-monitor setup) because of the known bug in the new xserver driver for xinerama. This messes up behaviour if the mouse goes either left or above the screen number 0, i.e. I had to make my left-most monitor screen 0. Everything worked out fine finally, I got my 3-monitor setup back with xinerama enabled to get one big desktop streched over 3 screens. Now the fun part: Every time I start up my machine only one of the 3 monitors gets a signal and is woken up: it only recognizes the left-most monitor (screen 0) and crams all the desktop stuff into this one screen. If I go into nvidia settings I only see one physical device although all 3 are connected and have power. When I look into the xorg.conf I can still see my old setup with 3 devices, 3 screens, xinerama active etc... But I was totally unable to get 3 montitors to work. (I tried unplugging monitors, reconfiguring whole nvidia setup, ...) But it gets even better: When I restart my machine (i.e. choose the restart option from the Ubuntu menu) it shuts down and tries to restart. The restart then gets stuck after showing the Ubuntu splash screen with the 'loading bar' (the moving dots thingy) and I am forced to kill the machine by cutting power. But after the power cut the machine boots up normally and suddenly I get my 3 monitor setup back up working. That is until the next time I shut down and start up, where it all starts over again and I only have one monitor... (see above) I really have a hard time seeing where the error is. It must be that the restart boot somehow differs from the 'normal' boot. But the fact that it gets stuck and I need to cut power which then basically triggers a 'normal' boot does not really support this theory... My setup (please tell me if you need further info): 3 monitors as 3 screens as one desktop (with xinerama) 2 nvidia cards where screen 0 and 1 are on card 0 and screen 2 is on card 1 Ubuntu 10.04 Lucid Lynx (updated from 9.10, 9.04, ....) I would appreciate every idea on the subject, at the moment I really don't have any clue what to do...

  Read the article

• DVD playback with Windows Media Player 11 works fine, but when copied to HDD and then played back, t

  - by stakx

  I have several DVDs with short documentaries on it. Since the notebook I'm using (a Dell Latitude E6400) has only one DVD drive, and I might play back those short movies very often, I thought of copying them to the HDD and playing them back from there. However, I've run into a problem, namely stuttering audio. Problem description: When I play back these movies directly from DVD (with Windows Media Player 11 under Windows Vista), everything works fine. Smooth video, no significant audio problems (only the occasional click). But as soon as I copy any of these DVDs to the HDD and try to play them back from there (e.g. using the wmpdvd://drive/title/chapter?contentdir=path protocol, I get stuttering audio — audio playback sounds like a machine gun for a third of a second or so, approx. every 8 seconds. I have tried converting the VOB files from the DVD to another format (ie. ripping), but that resulted in a noticeable downgrade of picture quality. Therefore I thought it best to keep the files in their original format, if possible. Still, I suspect that the stuttering audio is due to some (de-)muxing problem, and that changing the file format might help. (After all, video playback is fine; therefore I don't think that the hardware is too slow for playback.) Only thing is, I don't know how to convert the VOB files to another Windows Media Player-compatible format without quality loss. I hope someone can help me, or give me further pointers on things I could try out to get HDD playback to work without the problem described. Some things I've tried so far, without any success: VOB2MPG, in order to convert the .vob file to a .mpg file. But that changes only the A/V container, not the content. No re-encoding takes place at all. Re-encoding with MPlayer/MEncoder. Lots of quality loss there, and I frankly haven't got the time to test all possible settings combinations available. Disabling all plug-ins, equalizers, etc. in Windows Media Player. Disabling all hardware acceleration on the audio playback device. Further info on the VOB files I'm trying to playback: The video format is MPEG ES, PAL 720x576 pixels @ 24/25 frames per second. The sound stream is uncompressed PCM, 16-bit stereo @ 48kHz. (Might it help if I somehow re-encoded the sound stream at a lower resolution, or as an MP3? If so, how would I do this without changing the video stream?) P.S.: I am limited to using Windows Media Player (11). (I previously tried MPlayer btw., but the video playback quality was surprisingly bad.)

  Read the article

• how does openvpn decide which interface to get IP addrs from

  - by bkrupa

  Using ubuntu 10.04 on both ends. We have a client and server machine on the SAME network attempting to make a vpn connection. We use the config files from here and made minimal changes. The server and client start and seem to connect without any trouble. The server looks like: Wed Feb 23 22:13:22 2011 MULTI: multi_create_instance called Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Re-using SSL/TLS context Wed Feb 23 22:13:22 2011 192.168.1.55:47166 LZO compression initialized Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Control Channel MTU parms [ L:1574 D:138 EF:38 EB:0 ET:0 EL:0 ] Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Data Channel MTU parms [ L:1574 D:1450 EF:42 EB:135 ET:32 EL:0 AF:3/1 ] Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Local Options hash (VER=V4): 'f7df56b8' Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Expected Remote Options hash (VER=V4): 'd79ca330' Wed Feb 23 22:13:22 2011 192.168.1.55:47166 TLS: Initial packet from 192.168.1.55:47166, sid=69112e42 5458135b *...* Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Feb 23 22:13:22 2011 192.168.1.55:47166 [client1] Peer Connection Initiated with 192.168.1.55:47166 On the client side the connection looks like: Wed Feb 23 22:20:07 2011 [server] Peer Connection Initiated with [AF_INET]192.168.1.41:1194 Wed Feb 23 22:20:10 2011 SENT CONTROL [server]: 'PUSH_REQUEST' (status=1) Wed Feb 23 22:20:10 2011 PUSH: Received control message: 'PUSH_REPLY,route-gateway 10.8.0.4,ping 10,ping-restart 120,ifconfig 10.8.0.50 255.255.255.0' ... Wed Feb 23 22:20:10 2011 /sbin/ifconfig tap0 10.8.0.50 netmask 255.255.255.0 mtu 1500 broadcast 10.8.0.255 Wed Feb 23 22:20:10 2011 Initialization Sequence Completed The openvpn server has been configured to assign ip addresses in the range 10.8.0.* and the client has been given 10.8.0.50. When I run the following nmap from the client: Starting Nmap 5.00 ( http://nmap.org ) at 2011-02-23 22:04 EST Host 10.8.0.50 is up (0.00047s latency). Nmap done: 256 IP addresses (1 host up) scanned in 30.34 seconds Host 192.168.1.1 is up (0.0025s latency). Host 192.168.1.18 is up (0.074s latency). Host 192.168.1.41 is up (0.0024s latency). Host 192.168.1.55 is up (0.00018s latency). Nmap done: 256 IP addresses (4 hosts up) scanned in 6.33 seconds If I run an nmap from the server on 10.8.0.* I get nothing. If the client has two interfaces (wireless and tap device) when you look for a certain ip address, how does it decide which interface to connect on?

  Read the article

• Problems with Windows XP Plug and Play devices, maybe relating to MSVCR71.dll

  - by Richard

  I believe this question is unanswered as of now so I appologize if I've overlooked it. I have been having trouble some external devices with windows recently and I'm trying my darnedest to get to the bottom of it. At first, my Zero Tension USB mouse would stop working...as in the laser in the bottom of it would be on and would register movement, but the mouse on the screen wouldn't budge even an inch. At first this would happen randomly and then it would correct itself. As time went on, it became more and more frequent. At some point, the computer would make the "doo doo" sound of plugging or unplugging a USB device when the mouse stopped/started working. I dealt with it for a while and usually if I rebooted my machine, the mouse would work again for a day or two. As more time has gone on, the computer fully does not recognize the mouse AT ALL...I have another mouse that I use with the computer that works just fine and cannot seem to figure out why my Zero Tension mouse has failed. I tried plugging the Zero Tension mouse into my Mac and low and behold, it works without hesitation and never stops on me... Needless to say, I am stumped about this. I figured because I had another mouse I could deal with the loss of my fancy one for now...until my speakers stopped being recognized. I have a set of Logitec speakers that I have plugged into my sound card. Again, every now and again the audio devices would cease to be recognized by my computer, but a reboot would fix the problem. Now my speakers do not work at all with my computer and I feel like it's time to ask for help. My computer seems to be having a neural shutdown...where I can plug in devices and the computer doesn't seem to notice anything wrong, but none of the devices work. I hope this doesn't get any worse! Please help! Also, on a potentially (un)related note, when I start up my machine I get the message "This application has failed to start because Msvcp71.dll was not found. Re-installing the application may fix this problem." in reference to qbupdate.exe I don't know if that DLL being messed up has anything to do with my mouse or speakers, but I figure it might...anyway, thanks in advance for an answer and let me know if I need to clarify anything. Let me sum up: Zero Tension Mouse gradually stopped working Logitec Speakers gradually stopped working MSVCR71.dll seems to be messed up I don't know if any of those are related but any help would be much appreciated

  Read the article

• New monitor connected to HDMI adaptor doesn't show output after booting

  - by Paul

  Hello out there in the multiple monitors’ world. I am a very old newbie in your world and need help. I just purchased a new Asus VH236H monitor and hooked it up the HDMI port of an ATI Radeon HD4300 / 4500 Series display adaptor. I left the old Princeton LCD19 (TMDS) hooked up to the DVI port of the same display adaptor. Both monitors displayed the boot sequence, after I fired good old Sarastro2 (Asus P5Q Pro Turbo – Dual Core E5300 – 2.60 GHz) up. The Asus lacked one half of a second behind the Princeton until the Windows 7 Ultimate SP 1 boot up was complete. Then the Asus displayed “HDMI NO SIGNAL” and went into hibernation. The Princeton stayed lit up as before. Both monitors are displayed on the “Screen Resolution Setup Display” and I plaid around with them for a while. The only thing I accomplished was to shove the desktop icons from the Princeton to the still hibernating Asus. The “Multiple displays:” is set to “Extend these displays”, the Orientation is “Landscape” and the Resolutions are set on both to the “recommended” one. Both monitors show that they work properly in the advanced Properties display. What am I doing wrong, what am I missing? Never mind the opinions about the different resolutions of the two monitors. I always can unhook the Princeton and give it to a Goodwill Store if I do not like the setup. I just would like to make it work. Any constructive help is very much appreciated, Thank you. Thank you Anees Bakrain Only the ATI Radeon HD 4300/4500 Series adapter is displayed in the Device Manager, for that reason I have to assume that the onboard display adaptor is not active. All 40 drivers of Sarastro2 are up to date and the HDMI cable can not be the problem because both monitors displayed the boot sequence up to the moment when Windows 7 was loaded completely. This was the moment, when the Asus monitor lost its signal. Both connectors, HDMI and DVI are connected and removing the DVI connector would not solve my problem of running both monitors simultaneously. However, your suggestions shifted my seventy one year old brain into the next gear. The only question remaining is; “Why the signals to the Asus monitor stop after the sequence is complete”. The ATI Radeon HD 4300/4500 Series adapter seems to be capable of sending simultaneous HDMI and DVI signals, what is done during the boot sequence. Why do the signals change after the boot sequence is complete is the key question or der springende Punkt? Is this a correct assumption slhck?

  Read the article

• DELL DRAC & Ubuntu VPN Connection

  - by Mikunos

  I am trying to connect to a DELL DRAC card without success by Ubuntu VPN Connection Manager. I have these data: Protocol: PPTP SERVER IP PPTP: 1233.123.123.123 DRAC IP: 192.168.10.25 Subnet: 255.255.0.0 User: myuser Pass: mypass where have I to write these parameters? I have configured the PPTP connection using the graphical tool in Ubuntu 11.10 ... but in the /var/log/syslog I get these messages: Apr 15 11:33:15 shinet NetworkManager[1035]: <info> Starting VPN service 'pptp'... Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' started (org.freedesktop.NetworkManager.pptp), PID 18180 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' appeared; activating connections Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN plugin state changed: 3 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN connection 'Connessione VPN 1' (Connect) reply received. Apr 15 11:33:15 shinet pppd[18182]: Plugin /usr/lib/pppd/2.4.5/nm-pptp-pppd-plugin.so loaded. Apr 15 11:33:15 shinet pppd[18182]: pppd 2.4.5 started by root, uid 0 Apr 15 11:33:15 shinet pppd[18182]: Using interface ppp0 Apr 15 11:33:15 shinet pppd[18182]: Connect: ppp0 <--> /dev/pts/1 Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp0, iface: ppp0): no ifupdown configuration found. Apr 15 11:33:15 shinet pptp[18185]: nm-pptp-service-18180 log[main:pptp.c:314]: The synchronous pptp option is NOT activated Apr 15 11:33:46 shinet pppd[18182]: LCP: timeout sending Config-Requests Apr 15 11:33:46 shinet pppd[18182]: Connection terminated. Apr 15 11:33:46 shinet avahi-daemon[1081]: Withdrawing workstation service for ppp0. Apr 15 11:33:46 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:46 shinet pppd[18182]: Modem hangup Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet pppd[18182]: Exit. Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state changed: 6 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state change reason: 0 Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> error disconnecting VPN: Could not process the request because no VPN connection was active. Apr 15 11:33:51 shinet NetworkManager[1035]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Apr 15 11:33:57 shinet NetworkManager[1035]: <info> VPN service 'pptp' disappeared Thanks

  Read the article

• MBPro, mid 2010 can't see Dlink DIR655 signal after sleep etc

  - by user88114

  This is my son's MBP 7,1 running Snow Leopard 10.6.7. Router signal is fine since iPad, Wintel on same table 20 feet from router are fine. the MBP however frequently wakes and fails to find the internet. iStumbler can see 1 neighbours hub and my garden hub are there but can't get to the normal DIR655 wifi... no ping no en0 or en1 device seems to exist. Airport off and on does not help. He just resets router and it all works but this does not please me! I must admit the winter sometimes seems to loose connect too, but less so. The DIR655 (hardware rev A3) is on the original EU firmware 1.10, I'm cautious about jumping to latest 1.31EU since no downgrade seems to be possible and that feels a bit risky as so much is set up and working fine. If I use the DIR655 admin web and release the lease the MBP has then wake it all worked OK. So I suspect lease timing/locking issue but unsure how to check up, plus why iStumbler seems to say the network is not visible at all when I sit on the iPad right next to it just fine.. I do not think there are any channel overlaps and we also have RFquiet DECT phones (Orchid) that are silent until lifted or called. Anyway signals all show low interference and high throughput except for this failure to connect. Just walked the MBP to the garden office and iStumbler now sees the more distant DIR655 signal although it will not connect to it (does not show under Sys Prefs NetNetwork names) even after airport off & on... It also refuses to connect to my garden network (an old Belkin acting as AP wired to DIR655), the signal it can see and even net name in Sys Prefs NetNetwork names (2 mins later):NOW both names ARE visible, but both fail to accept the correct WPA2 password and keep asking again after failing to connect. IT ALL MAKES NO SENSE TO ME. Just revoked the lease for the MBP on DIR655 and no changes although this seemed to help MBP wake into connection 1 hour ago. OK a bit of walking about to report. Carried MBP across garden towards DIR655, a few other wifis show up on iStumbler, low signals all channel 1. Right next to DIR655 but iStumbler not showing it, although most other wifi's have gone. I'd say iStubler is suffering timeouts&hangs but hard to be sure. Lots of attempts to Airport on/off, join other etc and suddenly I get to connect, get given new IP (I revoked), can browse. Walk away, connection drops quite soon at 30 feet then reconnected briefly then died again. MUST ATTEND ELSEWHERE FOR A BIT...

  Read the article

• How to install missing Sound Drivers in Ubuntu?

  - by Sakamoto Kazuma

  I seem to be missing drivers for my Gateway laptop MA7. I have looked in System-Admin-Hardware Drivers, but it does not show up in there.There are also no devices listed in Sound-Hardware. I'm guessing at this point that I don't have the driver installed. However, I get the following output: admin@machine001:~$ cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xd8240000 irq 22 admin@machine001:~$ And my lspci shows: 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02) 04:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 04:09.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 04:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) I have also checked alsamixer, and nothing is muted. No headphones plugged into headphone jack either. So the question now is, how do I get sound to work on my laptop? It doesn't work for any application.

  Read the article

• Hot-swap drive got new name, can I change it on-the-fly?

  - by T.J. Crowder

  One of the HDDs in my server's RAID config failed, so I took it out of the array and had the data center hot-swap it. They've done that, but now the new drive is /dev/sdc rather than /dev/sda. I suspect — correct me if I'm wrong — that if I reboot the server, it will be /dev/sda again, so I'm hesitant to add it back to the array as /dev/sdc because I don't want to lay a trap for myself to fall into on the next reboot. I'd just as soon not reboot the server if I don't need to (if I do need to, well, too bad for me). Is there a way I can change the device name from /dev/sdc to /dev/sda without rebooting? This is on Ubuntu 10.04 LTS. It's an md array ("Linux Software RAID"), where currently one of the devices (there are a couple of them) looks like this ("degraded" because I've removed the old /dev/sda from it): # mdadm --detail /dev/md0 /dev/md0: Version : 00.90.03 Creation Time : Sun Oct 11 21:07:54 2009 Raid Level : raid1 Array Size : 97536 (95.27 MiB 99.88 MB) Used Dev Size : 97536 (95.27 MiB 99.88 MB) Raid Devices : 2 Total Devices : 1 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Jun 30 09:31:16 2011 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 UUID : 496be7a5:ab9177ed:7792c71e:7dc17aa4 Events : 0.112 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed Thanks, Update: Reading through the kernel md documentation, I suspect that if the name changes on reboot, it won't matter. (Good design, that.) Here's why: Boot time autodetection of RAID arrays When md is compiled into the kernel (not as module), partitions of type 0xfd are scanned and automatically assembled into RAID arrays. This autodetection may be suppressed with the kernel parameter "raid=noautodetect". As of kernel 2.6.9, only drives with a type 0 superblock can be autodetected and run at boot time. The kernel parameter "raid=partitionable" (or "raid=part") means that all auto-detected arrays are assembled as partitionable. I do have md compiled into the kernel, so I'm rebuilding the array now and will do the reboot to see what happens. Even if it works, the above doesn't answer the question I actually asked, so unless someone comes along and answers that question in the meantime (I'd be interested, even if it's not necessary for what I'm doing this very moment), I'll just delete the question to keep noise down.

  Read the article

• SSH Socks Proxy wiith iptables REDIRECT

  - by Radium

  I have googled and haven`t found the answer on my question. Help me please. There are two servers: serverA with public IP 12.0.0.10 and an private IP 10.0.0.5 serverB with public IP 20.0.0.11 I have setup SOCKS proxy on serverB to serverA: ssh -D20.0.0.11:2222 [email protected] So when on my local machine in a browser i specify SOCKS proxy 20.0.0.11:2222 (serverB:2222) as external IP while browsing i get 12.0.0.10 (serverA IP). That is ok. As well if i go onto http://10.0.0.5 (serverA private IP) it is also reachable. That is what i need. I want to make servers A private IP to be available through servers B public IP on certain ports but without specifying SOCKS in my browser. I could use ssh port forward but the problem is - i need to forward many ports and do not know which exactly - i know only the range. So when i connect to 20.0.0.11 to any port , for example, from 3000:4000 range, i want that traffic to be redirected to 10.0.0.5 on the same port. That is why i`ve decided maybe SOCKS proxy via SSH and iptables REDIRECT could help me. Client - serverBPublicIP (any port from range 3000:4000) - serverAPublicIP - serverAPrivateIP (the port was requested on serverBPublicIP) On serverB i do: ssh -D20.0.0.11:2222 [email protected] iptables -t nat -A PREROUTING -d 20.0.0.11 -p tcp --dport 3000:4000 -j REDIRECT --to-port 2222 But that does not work - when i telnet on 20.0.0.11:3001 for example i do not see any proxied traffic on the serverA. What should i do else? I have tried tcpsocks like this (in example i am telneting to 20.0.0.11:3001) Client -> 20.0.0.11:3001 -> iptables REDIRECT from 3001 --to-port 1111 -> tcpsocks from 1111 to 2222 -> SOCKS proxy from serverB to serverA on port 2222 -> serverA But i do not know what to do with the traffic on serverA. How to route it to its private IP. Help me please. I know, VPN removes all the hell i am trying to create, but i have no ability to use tun/tap device. It is disabled.

  Read the article

• Troubleshooting an NFS server hanging after authenticated mount request

  - by Christoph

  I need some advice on troubleshooting an NFS server problem on Scientific Linux (RHEL) 6.1. The log on the server shows that an authenticated mount request was made: Jan 13 16:30:02 ??? rpc.mountd[3996]: authenticated mount request from ????:784 for /shared-storage/cm/shared (/shared-storage/cm/shared) But after that, it does not continue. On the client, it is also hanging. The interesting thing now is that I have two NFS servers, which should be identical, and the one is working perfectly, but the other exhibits the above mentioned behaviour. The problem is also not completely persistent, i. e. sometimes the mount request succeeds. I assume that the problem must be related to the server rather than to the client, because it is working perfectly on the other server. My question is where I should search the problem. I have already re-created the exports using exportfs -r, I have restarted the NFS server, I have compared the rpcinfo outputs of both server - no success. The problem even survives a reboot. Any other ideas are appreciated. As answer to Tim's question: I have sporadically the following in dmesg, but do not know whether it is related e1000e 0000:0c:00.0: eth4: Detected Hardware Unit Hang: TDH <24> TDT <25> next_to_use <25> next_to_clean <24> buffer_info[next_to_clean]: time_stamp <1c3d12940> next_to_watch <24> jiffies <1c3d12940> next_to_watch.status <0> MAC Status <80383> PHY Status <792d> PHY 1000BASE-T Status <7800> PHY Extended Status <3000> PCI Status <10> Further edit: The problem above does not occur on the machine that is working, so it probably is related. Again an edit: The error is not on the (software) device that is used for NFS, but on another one. The NFS mount also does not trigger the message.

  Read the article

• How to get wireless working (properly) with Sitecom Wireless USB micro adapter 300N on Windows 7?

  - by Timo

  The question says it all, but more detail follows ;) I've got a new computer that runs Windows 7 64-bits (Home Edition) and I'd like to connect it to my wireless home network (Sitecom wireless gigabit router 300N wl-352 v1 002) with a Sitecom wireless USB micro adaptapter 300 wl-352 V2 001. After installing the router (i.e. connected to the modem and power) and ensuring that wireless is indeed enabled, I've installed the driver of the USB adapter on the new computer described above. After the installation (drivers and utility on CD) completes successfull I rebooted my computer and inserted the USB adapter. After discovering the right network and connecting to it using the network key, a connection is succesfully made. (Using the Sitecom 300N USB Wireless LAN utility). In the LAN utility I can see that the signal strength is approximately 50% and connection quality is approximately 80%. Judging from these numbers I assumed that all was fine and started to use the connection (reading news on nu.nl, a dutch news site), but noticed that the connection was lost several times in a very short time span, but each time the connections was resumed, resulting in the 50/80 percent numbers described above. However, the website was not loaded completely and often a timeout would be reported. When inspecting the drivers through Device Management (Windows' Apparaatbeheer in dutch) there were no errors/warnings; everything seemed to be in order. In an attempt to solve this, I downloaded the latest drivers for the USB adapter, but the problems remained. Finally I tried to connect the computer with a Siemens Gigaset USB Adapter 108. This process was a troublesome since I had to download a driver (from the site above) and tell Windows (7) to use the Windows Vista driver when installing the new hardware, since there is (was) no Windows 7 driver available. This resulted in a usable connection, although not very stable when reconfiguring the router. Which took the form of selecting a different wireless channel on the router, even using the Sitecom utility mentioned above to check if there were other networks communicating on that channel (and thus picking a channel that was not used by other networks). Again no result when changing back to the Sitecom USB adapter. Note that this means (I think) that I could use the internet connection with the Siemens adapter, meaning the problem was not in the router. So: How to get wireless working (properly) with Sitecom Wireless USB micro adapter 300N on Windows 7? PS Sorry, but should be able to post one link, while I had links in place for the USB adapter, router and the siemens adapter in place as well, but I'm not (yet) allowed to post these... (The site says I can post one link, but only when no links are present will it allow me to post the question...)

  Read the article

• WIndows 7 cannot boot - bootrec reports FS not found or corrupt

  - by purecharger

  For 3 days now I've been unable to boot into my Windows 7 partition, and all my research has been to no avail. I'm hoping someone here has more ideas on how to fix this. When I boot up now, I get the black screen with BCD error that says theres no valid file system or it may be corrupt (pardon my lack of detail, no copy/paste is available then). When I boot with the Windows 7 disc and go into repair tools, no operating system is found, and attempting to automatically repair the problem fails with Unknown Operating System (Unknown Disk) or something similar. When I drop into the command prompt, I am able to see and navigate my C:\ drive without issue. I attempt to use bootrec: C:\> bootrec /ScanOS Finds C:\Windows as a system partition. C:\> bootrec /RebuildBCD Fails with volume does not contain a recognized file system. please make sure that all required file system drivers are loaded and that the volume is not corrupted. So then I attempt to fix the bootsector: C:\> bootsect /nt60 C: /force Which completes successfully (sorry, no output..) Upon rebooting, I have the same problem. I've also tried all of the above after making my Windows partition active: C:\> diskpart DISKPART> select disk 1 DISKPART> select partition 1 DISKPART> active DISKPART> exit Then bootrec as above, both with and without a reboot after the DISKPART commands. Then I've also tried rebuilding the BCD store by hand: set systemdrive=C: set tempbcd=C:\boot\bcd.temp set tempfile=C:\boot\temp.txt bcdedit -createstore %tempbcd% bcdedit.exe -store %tempbcd% -create {bootmgr} -d "Windows Boot Manager" bcdedit -store %tempbcd% -create -d "Windows Vista" -application osloader>%tempfile% set /p winvistaguid= <%tempfile% set winvistaguid=%winvistaguid:~10,38% bcdedit -store %tempbcd% -set %winvistaguid% osdevice partition=%systemdrive% bcdedit -store %tempbcd% -set %winvistaguid% device partition=%systemdrive% bcdedit -store %tempbcd% -set %winvistaguid% path \Windows\system32\winload.exe bcdedit -store %tempbcd% -set %winvistaguid% systemroot \Windows bcdedit -import %tempbcd% However on the import, I get my familiar friendly message: volume does not contain a recognized file system. please make sure that all required file system drivers are loaded and that the volume is not corrupted I'm at my wits end here, and I cannot understand why Windows refuses to see this as a valid install. When I list the disk/partition in DISKPART, it shows up as NTFS and "Healthy", and I can navigate the directory structure from DOS with no problems. I really, really do not want to reformat and reinstall. I know this problem can be solved!

  Read the article

• UCARP: prevent the original master from taking over the VIP when it comes back after failure?

  - by quanta

  Keepalived can do this by combining the nopreempt option and the BACKUP state on the both nodes: Prevent VRRP Master from becoming Master once it has failed Prevent master to fall back to master after failure How about the UCARP? Name : ucarp Arch : x86_64 Version : 1.5.2 Release : 1.el5.rf Size : 81 k Repo : installed Summary : Common Address Redundancy Protocol (CARP) for Unix URL : http://www.ucarp.org/ License : BSD Description: UCARP allows a couple of hosts to share common virtual IP addresses in order : to provide automatic failover. It is a portable userland implementation of the : secure and patent-free Common Address Redundancy Protocol (CARP, OpenBSD's : alternative to the patents-bloated VRRP). : Strong points of the CARP protocol are: very low overhead, cryptographically : signed messages, interoperability between different operating systems and no : need for any dedicated extra network link between redundant hosts. If I don't use the --preempt option and set the --advskew to the same value, both nodes become master. /etc/sysconfig/carp/vip-010.conf # Virtual IP configuration file for UCARP # The number (from 001 to 255) in the name of the file is the identifier # $Id: vip-001.conf.example 1527 2004-07-09 15:23:54Z dude $ # Set the same password on all mamchines sharing the same virtual IP PASSWORD="pa$$w0rd" # You are required to have an IPADDR= line in the configuration file for # this interface (so no DHCP allowed) BIND_INTERFACE="eth0" # Do *NOT* use a main interface for the virtual IP, use an ethX:Y alias # with the corresponding /etc/sysconfig/network-scripts/ifcfg-ethX:Y file # already configured and ith ONBOOT=no VIP_INTERFACE="eth0:0" # If you have extra options to add, see "ucarp --help" output # (the lower the "-k <val>" the higher priority and "-P" to become master ASAP) OPTIONS="-z -k 255" /etc/sysconfig/network-scripts/ifcfg-eth0:0 DEVICE=eth0:0 ONBOOT=no BOOTPROTO= IPADDR=192.168.6.8 NETMASK=255.255.255.0 USERCTL=yes IPV6INIT=no node 1: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether c6:9b:8e:af:a7:69 brd ff:ff:ff:ff:ff:ff inet 192.168.6.192/24 brd 192.168.6.255 scope global eth0 inet 192.168.6.8/24 brd 192.168.6.255 scope global secondary eth0:0 inet6 fe80::c49b:8eff:feaf:a769/64 scope link valid_lft forever preferred_lft forever node 2: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:30:48:f7:0f:81 brd ff:ff:ff:ff:ff:ff inet 192.168.6.38/24 brd 192.168.6.255 scope global eth1 inet 192.168.6.8/24 brd 192.168.6.255 scope global secondary eth1:0 inet6 fe80::230:48ff:fef7:f81/64 scope link valid_lft forever preferred_lft forever

  Read the article

• WIndows 7 cannot boot - bootrec reports FS not found or corrupt

  - by purecharger

  For 3 days now I've been unable to boot into my Windows 7 partition, and all my research has been to no avail. I'm hoping someone here has more ideas on how to fix this. When I boot up now, I get the black screen with BCD error that says theres no valid file system or it may be corrupt (pardon my lack of detail, no copy/paste is available then). When I boot with the Windows 7 disc and go into repair tools, no operating system is found, and attempting to automatically repair the problem fails with Unknown Operating System (Unknown Disk) or something similar. When I drop into the command prompt, I am able to see and navigate my C:\ drive without issue. I attempt to use bootrec: C:\> bootrec /ScanOS Finds C:\Windows as a system partition. C:\> bootrec /RebuildBCD Fails with volume does not contain a recognized file system. please make sure that all required file system drivers are loaded and that the volume is not corrupted. So then I attempt to fix the bootsector: C:\> bootsect /nt60 C: /force Which completes successfully (sorry, no output..) Upon rebooting, I have the same problem. I've also tried all of the above after making my Windows partition active: C:\> diskpart DISKPART> select disk 1 DISKPART> select partition 1 DISKPART> active DISKPART> exit Then bootrec as above, both with and without a reboot after the DISKPART commands. Then I've also tried rebuilding the BCD store by hand: set systemdrive=C: set tempbcd=C:\boot\bcd.temp set tempfile=C:\boot\temp.txt bcdedit -createstore %tempbcd% bcdedit.exe -store %tempbcd% -create {bootmgr} -d "Windows Boot Manager" bcdedit -store %tempbcd% -create -d "Windows Vista" -application osloader>%tempfile% set /p winvistaguid= <%tempfile% set winvistaguid=%winvistaguid:~10,38% bcdedit -store %tempbcd% -set %winvistaguid% osdevice partition=%systemdrive% bcdedit -store %tempbcd% -set %winvistaguid% device partition=%systemdrive% bcdedit -store %tempbcd% -set %winvistaguid% path \Windows\system32\winload.exe bcdedit -store %tempbcd% -set %winvistaguid% systemroot \Windows bcdedit -import %tempbcd% However on the import, I get my familiar friendly message: volume does not contain a recognized file system. please make sure that all required file system drivers are loaded and that the volume is not corrupted I'm at my wits end here, and I cannot understand why Windows refuses to see this as a valid install. When I list the disk/partition in DISKPART, it shows up as NTFS and "Healthy", and I can navigate the directory structure from DOS with no problems. I really, really do not want to reformat and reinstall. I know this problem can be solved!

  Read the article

• Batch file to uninstall all Sun Java versions?

  - by Ricket

  I'm setting up a system to keep Java in our office up to date. Everyone has all different versions of Java, many of them old and insecure, and some dating back as far as 1.4. I have a System Center Essentials server which can push out and silently run a .msi file, and I've already tested that it can install the latest Java. But old versions (such as 1.4) aren't removed by the installer, so I need to uninstall them. Everyone is running Windows XP. The neat coincidence is that Sun just got bought by Oracle and Oracle has now changed all the instances of "Sun" to "Oracle" in Java. So, I can conveniently not have to worry about uninstalling the latest Java, because I can just do a search and uninstall all Sun Java programs. I found the following batch script on a forum post which looked promising: @echo off & cls Rem List all Installation subkeys from uninstall key. echo Searching Registry for Java Installs for /f %%I in ('reg query HKLM\SOFTWARE\microsoft\windows\currentversion\uninstall') do echo %%I | find "{" > nul && call :All-Installations %%I echo Search Complete.. goto :EOF :All-Installations Rem Filter out all but the Sun Installations for /f "tokens=2*" %%T in ('reg query %1 /v Publisher 2^> nul') do echo %%U | find "Sun" > nul && call :Sun-Installations %1 goto :EOF :Sun-Installations Rem Filter out all but the Sun-Java Installations. Note the tilda + n, which drops all the subkeys from the path for /f "tokens=2*" %%T in ('reg query %1 /v DisplayName 2^> nul') do echo . Uninstalling - %%U: | find "Java" && call :Sun-Java-Installs %~n1 goto :EOF :Sun-Java-Installs Rem Run Uninstaller for the installation MsiExec.exe /x%1 /qb echo . Uninstall Complete, Resuming Search.. goto :EOF However, when I run the script, I get the following output: Searching Registry for Java Installs 'DEV_24x6' is not recognized as an internal or external command, operable program or batch file. 'SUBSYS_542214F1' is not recognized as an internal or external command, operable program or batch file. And then it appears to hang and I ctrl-c to stop it. Reading through the script, I don't understand everything, but I don't know why it is trying to run pieces of registry keys as programs. What is wrong with the batch script? How can I fix it, so that I can move on to somehow turning it into a MSI and deploying it to everyone to clean up this office? Or alternatively, can you suggest a better solution or existing MSI file to do what I need? I just want to make sure to get all the old versions of Java off of everyone's computers, since I've heard of exploits that cause web pages to load using old versions of Java and I want to avoid those.

  Read the article

• Loss of wireless network connectivity when playing video via HDMI cable

  - by Jeff Fohl

  Hi Folks - New to Super User, so I hope this question fits in with the guidelines. Very strange problem I am having, and I am at a loss as to how to continue troubleshooting this one. The basic problem is that when I attempt to watch streamed video on a particular display device (an Optoma HD180 projector), my network connectivity drops like a stone to barely measurable levels. This is my setup: I have a Dell H2C 730x running Windows 7 64bit. This particular computer has two ATI Radeon HD 4800 video cards. I have two Samsung 22" monitors connected to one card, and an Optoma HD180 digital projector connected to the other card via an HDMI cable. My internet connection is normally a reliable 6Mbps. The problem I am having occurs when I stream video (or even just browse the web) on the Optoma Projector. When I do this, my internet connection drops to practically zero (just a few kilobits per second). When I move the browser away from the projector, and over to one of my Samsung monitors, the internet connection comes right back. Note that the Optoma projector is on and enabled as a third monitor all this time. I can move the mouse around on the projector without triggering the problem. I tried pinging my router when I was playing a movie on one of the monitors, and I get a 1 millisecond response. However, when I have the movie playing on the Optoma projecter, pinging the router gives me response times in the hundreds of milliseconds, or times out completely. So, it clearly is something local to my machine - and not some sort of throttling occurring down the line. I would think that it is possibly something to do with the HDMI driver conflicting somehow with my network driver (which is a USB-based wireless connection). This one has me really stumped. Anyone have any ideas? EDIT: I am now leaning towards the possibility that the HDMI cable is somehow interfering with the wireless network, when large amounts of data are being pushed through the cable. Is this possible?

  Read the article

< Previous Page | 604 605 606 607 608 609 610 611 612 613 614 615  | Next Page >