Search Results

Search found 19557 results on 783 pages for 'networking programming'.

Page 610/783 | < Previous Page | 606 607 608 609 610 611 612 613 614 615 616 617  | Next Page >

• "No more threads can be created in the system" in Network and Sharing Center

  - by Zell Faze

  A while back I noticed on one of our laboratory computers (Windows 7, very little extra software installed) that the network connection icon in the system tray would claim that it had no network connection, even though it did. This issue would go away after the computer was rebooted, but would surface again the next time I looked at the computer (a few days later). Upon opening the Network and Sharing Center I am shown an actual error message, but not one that seems to give me a lot of information about what the problem is. In the place of the usual information about network adapters and whether you are connected to the Internet it simply says: "No more threads can be created in the system." The Event Viewer shows hundreds of events from different services also with the same message. "Volume Shadow Copy Service error: Unexpected error calling routine CoCreateInstance. hr = 0x800700a4, No more threads can be created in the system."; "The WinHTTP Web Proxy Auto-Discovery Service service failed to start due to the following error: A thread could not be created for the service."; "The IP Helper service terminated with the following error: No more threads can be created in the system." As far as I can tell, this message seems to mean that there is some sort of resource leak in Windows where something is creating a large number of threads and those threads are not being killed off? I've tried restarting WMI and several services related to networking, without avail. Can anyone provide more information on what "No more threads can be created in the system" might mean and what I might be able to do to fix the issue? Currently the only solution appears to be restarting.

  Read the article

• 4in6 tunneling (via OpenVPN?)

  - by Deshene

  I have a local network with internet access. But unfortunately IPv4 internet connection speed is limited to 1mbps, which is realy sad. Fortunately I have a native IPv6, and there is no connection speed limit over IPv6. So, in order to get a good internet connection I made a plan: connect to the VPN-service over IPv6, and pass all IPv4 traffic through IPv6 tunnel, or something like that, I think you get the idea. I suggested to use service like HideMyAss.com, but unfortunately they don't support IPv6. The question is: Is there any existing VPN service that will make my dreams come true, and is easy to use, which I could connect over PPTP or OpenVPN (I want to set up connection to VPN in my router settings). Edit: It seems like there are couple of VPN services that supports IPv6 (it's odd, but the biggest VPN services support only IPv4), and there is none providing 4in6 tunnels. So, I came to the following solution: rent a VPS with IPv6 address, and manually setup 4in6 tunnel. I'm not good at networking, never did things like that, and don't know where to start, and what should I do. The use case, as I undestand, should look like this: I connect from my home computer to the VPS via OpenVPN, and after that all my IPv4 traffic pass through IPv6 (server do the job). OpenVPN - because I want to configure VPN connection to server in my router (Asus RT-N16?). How can I achieve this?

  Read the article

• Mac OS X 10.6 assign mapped IP to Windows 7 VM in Parallels

  - by Alex

  I'm trying to assign a mapped IP address to a Windows 7 VM. I have setup running in Parallels 5 in wireless bridged networking mode. The problem I am having is that it looks like the VM is actually broadcasting the MAC address of the host machine and thus causing a clash of IP addresses on the network. This is my current setup: Macbook Pro :~ ifconfig -a lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 inet 127.0.0.1 netmask 0xff000000 gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280 stf0: flags=0<> mtu 1280 en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 00:26:b0:df:31:b4 media: autoselect status: inactive supported media: none autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,flow-control> 10baseT/UTP <full-duplex,hw-loopback> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,flow-control> 100baseTX <full-duplex,hw-loopback> 1000baseT <full-duplex> 1000baseT <full-duplex,flow-control> 1000baseT <full-duplex,hw-loopback> fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078 lladdr 00:26:b0:ff:fe:df:31:b4 media: autoselect <full-duplex> status: inactive supported media: autoselect <full-duplex> en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::226:bbff:fe0a:59a1%en1 prefixlen 64 scopeid 0x6 inet 192.168.1.97 netmask 0xffffff00 broadcast 192.168.1.255 ether 00:26:bb:0a:59:a1 media: autoselect status: active supported media: autoselect vnic0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet 192.168.1.81 netmask 0xffffff00 broadcast 192.168.1.255 ether 00:1c:42:00:00:08 media: autoselect status: active supported media: autoselect vnic1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet 10.37.129.2 netmask 0xffffff00 broadcast 10.37.129.255 ether 00:1c:42:00:00:09 media: autoselect status: active supported media: autoselect Windows 7: :~ ipconfig -all Windows IP Configuration Host Name . . . . . . . . . . . . : Alex-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Parallels Ethernet Adapter Physical Address. . . . . . . . . : 00-1C-42-B8-E7-B4 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Teredo Tunneling Adapter Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{ACAC7EBB-5E5F-4F53-AFD9-E6EAEEA0FEE2}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Billion Bipac 7200 modem router: In DHCP server settings have the following two mapping entries. alex-macbook-win7 00:1c:42:00:00:08 192.168.1.98 alex-macbook 00:26:bb:0a:59:a1 192.168.1.97 The problem I have is that when the VM starts up it gets assigned the 192.168.1.97 address instead of the .98 address and thus networking on the host stops working as it says there is a clash. I have tried removing the mapping for "alex-macbook" which results in the guest machine being assigned a normal DHCP address and NOT the one that is in the mapping of the router.

  Read the article

• SQL Server 2005 Merge Replication to SQL Server CE 3.5

  - by user33067

  Hi, In my organization, we have a SQL Server 2005 database server (DBServer). Users of an application will normally be connected to DBServer, but, occasionally, would like to disconnect and continue their work on a laptop using SQL Server Compact Edition 3.5 (SQLCE). Due to this, we have been looking into using Merge Replication between the DBServer and SQLCE. From what I have read about this process, IIS must be installed on "the server"... yet, I have found no indication to whether this is talking about DBServer or SQLCE. I had assumed the documentation was referring to DBServer and proposed this to our networking staff. That idea was quickly put to rest as it is not our policy to install IIS on an internal server. This is where our SQL Server 2005 web server (WebServer) entered the picture. The idea being that IIS would be installed on WebServer and would be the conduit for DBServer and SQLCE to communicate. This sounded like a good idea at first, until I started looking for documentation on this type of setup. Everything I have been able deals with a DBServer -- SQLCE -- DBServer setup... nothing on DBServer -- WebServer -- SQLCE -- WebServer -- DBServer. Questions: Is going with a 3 server setup ideal? Does anyone have documentation on this type of setup? Does IIS even need to be running on one of the big servers, or can it just run off the laptop with SQLCE on it? (I'd really like this option ;))

  Read the article

• DKIM- Filter No Signature Data

  - by Vineet Sharma

  I have installed DKIM-Filter on Postfix after reading this tutorial http://www.unibia.com/unibianet/systems-networking/how-setup-domainkeys-identified-mail-dkim-postfix-and-ubuntu-server My email now has a DKIM signature but still it is landing in the SPAM folder. Here is the header Received-SPF: neutral (google.com: 69.164.193.167 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=69.164.193.167; Authentication-Results: mx.google.com; spf=neutral (google.com: 69.164.193.167 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected]; dkim=hardfail (test mode) [email protected] Received: from promote.a2labs.in (localhost [127.0.0.1]) by promote.a2labs.in (Postfix) with ESMTPA id 34858530E8 for <[email protected]>; Mon, 28 Feb 2011 12:23:07 +0530 (IST) DKIM-Signature: v=1; a=rsa-sha256; c=simple/simple; d=a2labs.in; s=mail; t=1298875987; bh=bo+H1VYPIHMja2u7i1lnzr4k/j4Pe8iSf79bVw94XpI=; h=To:Subject:Message-ID:Date:From:Reply-To:MIME-Version: Content-Type:Content-Transfer-Encoding; b=nhTdlnUwo0iUJ92ycQzKSRjw 5Pfya0DJcJrAc8Mr2hIv8OLpgzBCzdOMWTGqR5nuUmAzgCGYBhYAM2XZwVxo9JG/iz7 oYKysmNQnskFx0TRyW3UOkDWcfHcPnCL6Y7fGzZWinmsyjsg47k+mKZg/e8jqlwTAMO PYKkt5pBz7SM0= Also my mail.err file shows Feb 28 12:17:03 ivineet dkim-filter[32181]: 1F788530E1: no signature data Feb 28 12:18:02 ivineet dkim-filter[32181]: 432BA530E2: no signature data How to fix it

  Read the article

• cPanel web servers mounting home partition to a NAS or SAN

  - by Scott

  Hello, I currently have 2 cPanel web servers that are little 1RU dual cpu quad core xeons. They have a lot of resources for processing and handling web requests, and never exceed more than 10% cpu usage. They also have plenty of RAM. The problem is though that they both have RAID 1 160Gb SAS hard disk drives in them that are 75% full, and growing by the day. I didnt think that the amount of disk usage would be so high, but due to the nature of the sites hosted, this has become an issue. The easy fix would be just to upgrade the hard drives to something bigger (probably not of the SAS variety), but I am thinking of keeping the current machines as "processing servers" and buying a central "storage server" with about 12TB of storage. The /home/ partition on each of the 1RU servers would be mounted to a NAS or SAN point on this central storage server. My questions are: - Has anyone got a cPanel setup where they mount /home/ to a NAS or SAN elsewhere? If so, can you provide details as to what you did and how it went :) - Any recommendations on networking? Is gigabit ethernet enough? Is TCP/IP going to be a noticable performance problem? Anyone used a TOE key? - Anyone benchmarked or had any performance issues with SAN over NAS? Any help greatly appreciated. Scott

  Read the article

• Windows Authentication behaves oddly when VPN'd

  - by Dan F

  Hi all We've got a few apps that rely on windows authentication - a couple of web apps with AD auth turned on and we usually connect to our SQL servers with windows auth. This normally runs without a hitch. It doesn't work so well if we're VPN'd to a client site though. SSMS Opening SSMS normally from the start menu, then picking a server that normally accepts windows auth, results in a message saying: Login failed. The login is from an untrusted domain and cannot be used with Windows authentication. (.Net SqlClient Data Provider) If I drop to a command prompt and use runas /user:domain\user to launch SSMS I can successfully windows auth to our SQL server instances with that ssms process. If I look in task manager, both copies of ssms.exe (start menu vs runas) have the same user, and I can see no discernible differences between the processes in procexp. AD Auth websites If I open IE and browse to any of our websites that require an authenticated windows user, I get the "who are you" prompt, and that dialog thinks I'm whoever the VPN user is. I can click "Use another account" and authenticate that way though. Outlook Even Outlook prompts for a username when we are VPN'd! It's affecting our Win7 and Vista machines. It's been a while since we had an XP box, but I don't recall having this issue on XP for what it's worth. The VPN connections are just using the built in windows VPN connections, they're not fancy cisco VPNs or anything of that nature. Does anyone know how to tell windows that I'd like to be my normal old primary domain user rather than the VPN user when authenticating to resources in our domain? Heck, I'd be happy with a solution that prompted me with the "who are you" if I was trying to access windows auth requiring resources on the client's VPN. Thanks! Apologies if this is more a superuser question, I wasn't sure which site it best suited. It's about networking and infrastructure and plagues all of our developers here, so I hope it's a serverfault Q.

  Read the article

• Tools to (privately) annotate/markup a website for maintenance

  - by rob

  I've been tasked with updating a website. Rather than proofreading and updating each page (one at a time), I want to make a single pass over the entire website, marking graphics/images/videos that need to be rewritten, removed, or updated. I thought about taking screenshots, marking those up, and putting them in our bug-tracking database, but that seems like an extremely tedious solution. Some of the content is similar on various pages across the website, and the entire site itself is localized into several languages (so any changes made to the English version will have corresponding changes for other languages). I also want all of my markup to remain private (that is, if it's stored online somewhere, I should be the only person who can see my comments). I found an article that lists several website annotation services, but it's not clear whether they allow private annotations, or whether these tools are even appropriate for website maintenance (many of them look more geared toward social networking). I've started making a list of some necessary and desired features below, and may add more as necessary. Annotations/markup/comments remain private (only visible to me) Comment history/tagging (so I can reuse the same comment for shared footers, items requiring similar updates, etc.) Ability to print/export a list or report of all comments for the entire website Ability to produce a categorized list of changes (e.g., to produce a list of images that need updating, which I can send to the graphic designer) What processes and tools do you use to keep track of all the changes that need to be made to a website? What features are painfully absent from the tools you use?

  Read the article

• Distributed development staff needing a common IP range

  - by bakasan

  I work on a development staff that is geographically distributed, mostly all throughout the state of CA, but several key members also must travel frequently. We rely quite heavily on a 3rd party provider API for a great deal of our subsystems (can't get into who it is or what they do). The 3rd party however is quite stringent on network access and have no notion of a development sandbox. Access is restricted to 2, 3 IP numbers and that's about it. Once we account for our production servers, that leaves us with an IP or two to spare for our dev team--which is still problematic as people's home IP changes, people travel, we have more than 2 devs, etc. Wide IP blocks are not permitted by the 3rd party. Nor will they allow dynamic DNS type services. There is no simple console to swap IPs on the fly either (e.g. if a dev's IP at home changes or they are on the road). As none of us are deep network experts, I'm wondering what our viable options are? Are there such things as 3rd party hosts to VPNs? Generally I think of a VPN as a mechanism to gain access to a home office, but the notion would be a 3rd party VPN that we'd all connect to and we'd register this as an IP origin w/ our 3rd party. We've considered using Amazon EC2 to effectively host a dev environment for each dev and using that to connect. Amazon only gives you so many static IPs however (I believe 5?) so this would only be a stop gap solution until our team size out strips our IP count at Amazon. Those were the only viable thoughts that I had, but again, I'm far from a networking guy. Tried searching for similar threads, but I'm not even sure I know the right vernacular to look around for.

  Read the article

• Openfiler iSCSI performance

  - by Justin

  Hoping someone can point me in the right direction with some iSCSI performance issues I'm having. I'm running Openfiler 2.99 on an older ProLiant DL360 G5. Dual Xeon processor, 6GB ECC RAM, Intel Gigabit Server NIC, SAS controller with and 3 10K SAS drives in a RAID 5. When I run a simple write test from the box directly the performance is very good: [root@localhost ~]# dd if=/dev/zero of=tmpfile bs=1M count=1000 1000+0 records in 1000+0 records out 1048576000 bytes (1.0 GB) copied, 4.64468 s, 226 MB/s So I created a LUN, attached it to another box I have running ESXi 5.1 (Core i7 2600k, 16GB RAM, Intel Gigabit Server NIC) and created a new datastore. Once I created the datastore I was able to create and start a VM running CentOS with 2GB of RAM and 16GB of disk space. The OS installed fine and I'm able to use it but when I ran the same test inside the VM I get dramatically different results: [root@localhost ~]# dd if=/dev/zero of=tmpfile bs=1M count=1000 1000+0 records in 1000+0 records out 1048576000 bytes (1.0 GB) copied, 26.8786 s, 39.0 MB/s [root@localhost ~]# Both servers have brand new Intel Server NIC's and I have Jumbo Frames enabled on the switch, the openfiler box as well as the VMKernel adapter on the ESXi box. I can confirm this is set up properly by using the vmkping command from the ESXi host: ~ # vmkping 10.0.0.1 -s 9000 PING 10.0.0.1 (10.0.0.1): 9000 data bytes 9008 bytes from 10.0.0.1: icmp_seq=0 ttl=64 time=0.533 ms 9008 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=0.736 ms 9008 bytes from 10.0.0.1: icmp_seq=2 ttl=64 time=0.570 ms The only thing I haven't tried as far as networking goes is bonding two interfaces together. I'm open to trying that down the road but for now I am trying to keep things simple. I know this is a pretty modest setup and I'm not expecting top notch performance but I would like to see 90-100MB/s. Any ideas?

  Read the article

• Mac Management and Security

  - by Bart Silverstrim

  I was going through some literature on managing OS X laptops and asked someone some questions about usage scenarios when using the MacBooks. I asked someone more knowledgeable than I about whether it was possible for my Mac to be taken over if I were visiting another site for a conference or if I went on a wifi network at a local coffee house with policies from an OS X Server with workgroup manager (either legit for the site or someone running a version of OS X Server on hardware they have hidden somewhere on the network), which apparently could be set up to do things like limit my access to Finder or impose other neat whiz-bang management features. He said that it is indeed possible for it to happen as it would be assigned via the DHCP server and the OS X server would assume my Mac is a guest and could hand out restrictions and apparently my Mac will happily accept them without notifying me or giving me an option, unlike Windows which I believe would need to be joined to a domain before it becomes "managed" by Active Directory. So my question is as network admins and sysadmins with users traveling with MacBooks, is there a way to reasonably protect your users from having their machines hijacked without resorting to just turning off networking all the time? Or isn't this much of a security hazard? What threat does this pose to the road warriors in your businesses?

  Read the article

• How can a CentOS 6 guest running in VirtualBox be configured as a LAMP server that can be accessed from the Windows host?

  - by jtt89

  I was able to conect Centos6 on Virtual Box to Windows (I can ping in both directions) with Host-only Adapter (for connection between the two) and NAT Adapter (to enable Linux on VB to connect to the Internet). I want to set up httpd, mysql and vsftpd servers and in the end easily connect to httpd from Windows based browser and ftp server with a Windows based client as well. I would also want to have access through SSH. I have a general idea of the steps that are involved, but there is also a configuration that I am not sure about at this point. Lets say I follow these steps: yum install httpd yum install php php-pear php-mysql yum install mysql-server mysql_secure_installation yum install vsftpd yum install mod_ssl Technically I have everything installed, but what would be the next steps that I need to take (from the networking point of view, so to speak) to get it all working)? I know I need to configure, at least Apache, and ftp server, but I am not sure how is it gonna work; like where am I gonna be uloading the sites (I know this can vary), how am I gonna know what address to use in a browser if I wanna go to a website x, y, z on that installation etc. This sounds like I need to do some kind of DNS setup and I am kind of stuck at this point. If somebody could give me a general outline of what are the things that need to be done that would be great (I was looking at a lot of websites and I know about etc/sysconfig/network, httpd.config - not too much about it on Apache's site, hostname, hostname -f etc; but it is kind of hard to piece it all together at this point). I am gonna be looking at the books also, but they not always reflect the setup that I have too (VirtualBox). Thank you.

  Read the article

• Multiple vlans access to shared pbx system

  - by Matt

  I'm new to networking and was looking for some assistance. First off I'm using packet tracer to diagram my scenario as I will be receiving my equipment next week to deploy. Hardware to be used: 2 catalyst 3560 switches all connect to a sonic wall router I have two companies that work in the same office space. I need to keep these companies separate on their own vlan. They will however need to share the phone system. (Packet tracer file uploaded to give those who have the time to see what I put together.) http://dl.dropbox.com/u/86234623/network%20build.pkt Here is my current test scenario: on switch 0 I have: company A on vlan 2 computers 172.16.1.100 and 101 255.255.0.0 FA0/10 FA0/11 company B on vlan 3 computers 172.16.2.102, 255.255.0.0 FA0/12 PBX on a trunk port 172.16.0.5, 255.255.0.0 FA0/5 trunk port on FA0/1 to connect the switches on switch 1 I have: company A on vlan 2 computers 172.16.1.102, 255.255.0.0 company B on vlan 3 computers 172.16.2.100 and 101, 255.255.0.0 trunk port on FA0/1 to connect the switches I can ping the respective computers on the same vlan but cant ping company A to B which is what I want. However neither company can talk (ping) the PBX. Here are the commands I used to configure what I have: switch 0 en conf t vlan 2 name A vlan 3 name B int fa0/10 switchport mode access switchport access vlan 2 int fa0/11 switchport mode access switchport access vlan 2 int fa0/12 switchport mode access switchport access vlan 3 int fa0/5 switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3 int fa0/1 (to connect the switches) switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3 Switch 1 en conf t vlan 2 name A vlan 3 name B int fa0/10 switchport mode access switchport access vlan 3 int fa0/11 switchport mode access switchport access vlan 3 int fa0/12 switchport mode access switchport access vlan 2 int fa0/1 (to connect the switches) switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3

  Read the article

• KVM work with bridge network problems

  - by isware

  I try to configure bridge network for KVM(refer to http://www.linux-kvm.org/page/Networking), and it worked for Guest OS, but I have two problems with my Fedora host OS: 1?I can not access internet on host 2?The bridge configuration lost after reboot, I need to execute "service network restart" again to bring it up I checked here(http://serverfault.com/questions/168119/kvm-network-bridge-with-public-static-ip-for-both-host-and-guests) for the first problem, it seems not working for me. Any advice is appreciated! ifconfig -a eth0 Link encap:Ethernet HWaddr 48:5B:39:ED:EB:5A inet6 addr: fe80::4a5b:39ff:feed:eb5a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:231340 errors:0 dropped:0 overruns:0 frame:0 TX packets:413424 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:15335606 (14.6 MiB) TX bytes:114755796 (109.4 MiB) Interrupt:44 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:119307 errors:0 dropped:0 overruns:0 frame:0 TX packets:119307 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:57151264 (54.5 MiB) TX bytes:57151264 (54.5 MiB) sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) sw0 Link encap:Ethernet HWaddr 48:5B:39:ED:EB:5A inet addr:192.168.1.133 Bcast:255.255.255.255 Mask:255.255.255.0 inet6 addr: fe80::4a5b:39ff:feed:eb5a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:229584 errors:0 dropped:0 overruns:0 frame:0 TX packets:401232 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11047463 (10.5 MiB) TX bytes:113891533 (108.6 MiB) tap0 Link encap:Ethernet HWaddr F2:86:1A:48:E2:55 inet6 addr: fe80::f086:1aff:fe48:e255/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:232 errors:0 dropped:0 overruns:0 frame:0 TX packets:2744 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:24842 (24.2 KiB) TX bytes:243899 (238.1 KiB) virbr0 Link encap:Ethernet HWaddr 9A:7C:09:6B:85:65 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:46 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:5513 (5.3 KiB)

  Read the article

• Public DNS redirect subdomain to Windows Server 2003 DNS

  - by user125248

  I'm a programmer by trade but often dabble in sysadmin tasks and responsibilities. I have recently been tasked with setting up a Windows Server 2003 networking environment for a small business with multiple branches. The business already has a domain name they use to host a website at www.example.com. Currently the DNS nameservers are at Zerigo and I would very much like it to remain that way (as they specialize in just providing DNS services and they do this very well). We also have a bunch of other subdomains we use to conviniently connect to the various branches that have static IPs assigned from ISPs, so we're able to connect easily to branch1.example.com. Is it possible to 'redirect' all intranet.example.com DNS requests to a Windows box? I've been doing a little reading and I see there are NS records that might be able to do this, and the Windows DNS server could then perform all of the lookups for that subdomain, say, server1.intranet.example.com or client5.intranet.example.com. This would seem better to me, than registering a new domain name for the organisation, as keeping a single domain name makes more organizational sense.

  Read the article

• Windows 2003 Active Directory Integrated DNS zone not registering non-domain computers

  - by Jeff Willener

  I'm not a networking guy by all means, I'm just a developer who dabbles enough to get into trouble and I'm there. So bear with me... :) At my office I have a Windows 2003 Domain Controller which also services DNS. On the domain I have a handful of computers and other misc. equipment/toys. For the DNS I only created a Forward Lookup Zone for my domain (mydomain.com). I run a lot of VM's so generally I have everything on the domain, however some of those VM's are not and only in a 'Workgroup'. I also have another laptop which belongs to another domain (otherdomain.com) which is here 100% but I use it for other purposes and has to belong to the otherdomain.com. With all that said, I have two questions: I have found any computer not on mydomain.com does not register it's IP address even though 'Register this connections address in DNS' is set to in the 'Advanced TCP/IP Settings' for the nic. Where have I messed this up? On the laptop which is registered on otherdomain.com, when I do a nslookup for a computer on mydomain.com (e.g. nslookup devbox1) it appends otherdomain.com as the suffix (e.g. queries devbox1.otherdomain.com). Same thing occurs if I use the fully qualified name. In the 'Advanced TCP/IP Settings' for that nic, I can 'Append these DNS suffixes' of mydomain.com but I fear that will hose my DNS lookups when I VPN to otherdomain.com. So what is the correct approach to resolve this issue? Do I add both mydomain.com and otherdomain.com in that order?

  Read the article

• access an IP restricted service from a dynamic IP (Broadband modem) on a windows machine

  - by Joel Alenchery

  Hi, I dont know if this is the correct place to ask this question but here goes .. (please note that I am pretty much a newbie in terms of networking and I work primarily on the windows platform) I have been working on accessing and consuming some web services in C#/ASP.Net, these web services that I consume are IP restricted. Currently they allow access only from my work network (we have a static ip set up through which all our internet requests are routed). Every now and then we have people who go out and about and are stuck with using a usb dongle based internet connection and hence are not able to now access these web services that they are working on. What I would like to do is to provide some way for these remote workers to access the IP restricted web services using the static ip at our office. For example when the remote worker tries to access a service say http://exampleService.com .. the request gets routed to some box at our office and then out to the actual service. That way the service always sees the static ip of the office and not the dynamic ip that the remote user is actually using. I have done a fair bit of googling and its difficult to search for it as most of the results come back for dynamic DNS which is not really what I am looking for. I have also looked at a couple of posts on here namely Accessing IP restricted server from dynamic IP which does provide some insight but the fellow seems to have access to the source that does the ip restriction and is able to change the restrictions. In my case i dont have that access. another one that looked interesting was Static IP for dynamic IP the first answer seems exactly what I need but I dont know how I would go about doing the same on a windows machine. any help would be really appreciated. (am sorry about being soo noob-ish) PS: Right now everyone is using RDC/LogMeIn to access an internet connected machine in the office to manually check the webservice and getting work done. Which is a very tedious process.

  Read the article

• access an IP restricted service from a dynamic IP (Broadband modem) on a windows machine

  - by Joel Alenchery

  Hi, I dont know if this is the correct place to ask this question but here goes .. (please note that I am pretty much a newbie in terms of networking and I work primarily on the windows platform) I have been working on accessing and consuming some web services in C#/ASP.Net, these web services that I consume are IP restricted. Currently they allow access only from my work network (we have a static ip set up through which all our internet requests are routed). Every now and then we have people who go out and about and are stuck with using a usb dongle based internet connection and hence are not able to now access these web services that they are working on. What I would like to do is to provide some way for these remote workers to access the IP restricted web services using the static ip at our office. For example when the remote worker tries to access a service say http://exampleService.com .. the request gets routed to some box at our office and then out to the actual service. That way the service always sees the static ip of the office and not the dynamic ip that the remote user is actually using. I have done a fair bit of googling and its difficult to search for it as most of the results come back for dynamic DNS which is not really what I am looking for. I have also looked at a couple of posts on here namely http://serverfault.com/questions/187231/accessing-ip-restricted-server-from-dynamic-ip which does provide some insight but the fellow seems to have access to the source that does the ip restriction and is able to change the restrictions. In my case i dont have that access. another one that looked interesting was http://serverfault.com/questions/136806/static-ip-for-dynamic-ip the first answer seems exactly what I need but I dont know how I would go about on a windows machine. any help would be really appreciated. (am sorry about being soo noob-ish) PS: Right now everyone is using RDC/LogMeIn to access an internet connected machine in the office to manually check the webservice and getting work done. Which is a very tedious process.

  Read the article

• LAMP server VM issues

  - by nullArray

  After getting a recommendation to salvage a wiki by installing a LAMP server, I went on the prowl for a good virtualized one. I used the VMware Player version. Since the windows box has Bonjour, I can, for example, go to http://lamp.local. and it works see the web client. The problem is, I can't ssh to a directory to scp the files I need, mount a usb thumbdrive (usbfs is unsupported) nor get samba working. I can't even update the ubuntu installation, it fails. I've tried bridged, nat and host-only networking settings in VMware Player. Bridged gives me an undefined IP, while the other two each have different IPs. All three settings allow me to access the web config, but none of them give me samba access. Windows usually freezes, then reports that it cannot connect. I'd rather not wipe a box to do a dedicated install, is there I way I can get this VM working, or are there better LAMP VMs out there? This one came already working and set up with VMware Player, so I thought it would be perfect... Thanks,

  Read the article

• Windows Server 2003 with Apache and IIS causing random faulting and performance issues with Apache?

  - by contrebis

  I'm trying to fix a problem on a Windows Server 2003 SE install which is running IIS6 and Apache webserver (with PHP and MySQL). IIS sites are bound to one IP, Apache to the other. Everything seemed fine till the other IP address was installed to allow a webservice to run under IIS. Symptoms: Apache now responds very slowly, even requests for static files (often 30 seconds or more) Sporadic errors are appearing in the event logs like: Faulting application httpd.exe, version 2.2.14.0, faulting module php5ts.dll, version 5.2.13.13, fault address 0x000ac14f. I've double-checked the config files, taken account of this question/answer http://serverfault.com/questions/51230/running-iis-and-apache-on-the-same-windows-server, upped the Apache log level to debug, run TCPView to check for conflicting bindings, upgraded to latest Apache/PHP versions but still no success or indication of a cause. Any suggestions on where to look, or debugging tips would be gratefully received. I'm a web programmer so not so familiar with Windows Server admin or details of the networking stack. Running PHP under IIS is not an option and hosting on another server is non-ideal.

  Read the article

• Mac Management Without Permission and Security

  - by Bart Silverstrim

  I was going through some literature on managing OS X laptops and asked someone some questions about usage scenarios when using the MacBooks. I asked someone more knowledgeable than I about whether it was possible for my Mac to be taken over if I were visiting another site for a conference or if I went on a wifi network at a local coffee house with policies from an OS X Server with workgroup manager (either legit for the site or someone running a version of OS X Server on hardware they have hidden somewhere on the network), which apparently could be set up to do things like limit my access to Finder or impose other neat whiz-bang management features. He said that it is indeed possible for it to happen as it would be assigned via the DHCP server and the OS X server would assume my Mac is a guest and could hand out restrictions and apparently my Mac will happily accept them without notifying me or giving me an option, unlike Windows which I believe would need to be joined to a domain before it becomes "managed" by Active Directory. So my question is as network admins and sysadmins with users traveling with MacBooks, is there a way to reasonably protect your users from having their machines hijacked without resorting to just turning off networking all the time? Or isn't this much of a security hazard? What threat does this pose to the road warriors in your businesses?

  Read the article

• Unable to activate Windows XP

  - by Josh Kelley

  The latest round of Patch Tuesday updates left my Windows XP computer unbootable. ("Fatal System Error: The Windows Logon Process system process terminated unexpectedly.") After much messing around with the recovery console, an XP CD's repair mode, and manually copying registry files around, I have a system that can boot again. However, I overwrote my OEM XP installation's activation information while trying to run a retail XP CD's setup, so it needs reactivation. Here's my problem: I cannot activate it at all. I log in, Windows tells me I have to activate to continue, I click Yes, and absolutely nothing happens: no windows, no response to keyboard or mouse, no response to Ctrl-Alt-Del, nothing. Safe mode works, but I can't activate in safe mode (EDIT: not even safe mode with networking). I read a trick online of pressing [Windows Key]+U to bring up the Microsoft Narrator, and that works, but clicking its Microsoft Web Site link does nothing. My last attempt to resolve this was to reinstall Windows off of the OEM CD. Now I have two parallel Windows installations, both on the same hard drive, one with all of my stuff and no way to activate it, one fully activated with no usable programs. Any ideas? Any way to activate in safe mode? Any way to copy activation information from my activated installation to my unactivated installation (since they're both on the same hard drive)?

  Read the article

• Sophos UTM in Hyper-V

  - by TheD

  So, I had a previous thread about this Virtualizing Firewalls/UTM. Essentially, I have configured what I think would work, but networking isn't my strong point! Two Virtual Adapters - with IP addresses 192.168.0.2 (External) and 192.168.0.3 (Internal) respectively. The External Adapater looks at 192.168.0.1 (my Zyxel) for it's default gateway. The Internal Adapter, 192.168.0.3, which is what the Sophos UTM listens on, has it's default gateway set to 192.168.0.2, the IP of the External Lan interface. So, PC (192.168.0.11, DHCP) --> (LAN) --> Switch --> 192.168.0.3 (Internal LAN Interface IP) --> Sophos UTM --> 192.168.0.2 (External LAN Interface IP) --> 192.168.0.1 --> Internet Would this be the correct setup, or am I completely out of the game here? Cheers!

  Read the article

• Acer Aspire one is falling apart on Ubuntu

  - by Narcolapser

  Question: How do I have my netbook detect and install hardware? Info: I have an Acer Aspire One, it came with windows XP and I loaded it with Win7. I decided I wanted to change to Ubuntu so I tried Ubuntu netbook remix, which failed horribly, and so after attempting 3 or so other OS's I ended with Ubuntu Desktop 9.10. Which worked fine for a while, but there were some minor issues so I asked a question about it here and decided to change my OS again. This last weekend I tried mandriva like that guy in my other question suggested, no success. when I had though my netbook lost the ability to use it's touch pad, I didn't think much of it, just thought it must be a driver or something. But When Mandriva failed, and I also while I was at it tried Damn small linux and Debian, which both failed to, I decided to switch back to Ubuntu Desktop(some where in here my keyboard stopped working for one attempt to). But first I gave the netbook remix one more try. it worked this time, with the exception of it didn't have any networking. I thought it was a driver issue again and finished the weekend with ubuntu desktop 9.10 again. But now things get really crazy. it doesn't know it has a wireless card or an ethernet card. It doesn't know my phone is connected trying to provide wireless broadband either. I'm clueless on what could be the problem. And with only a minimal amount of experience with Ubuntu can't navigate the entire interface with only my keyboard(it doesn't detect a USB mouse when I plug it in, it had when I installed it. in fact the network interfaces were working just fine when I live boot ubuntu to installed it). Even so, I don't know where to go or what to do to make it recognize it's hardware. I'm in a dire situation, any help is welcome.

  Read the article

• Setup of high-end web server and DB server cluster on Amazon EC2: Is this how it's done?

  - by user1086584

  Amazon is so technical, I want to confirm that my understanding is correct. We have a large 500 GB database. (OrientDB.) We will have it mirrored to one another in the same Availability Zone. We believe the database size will grow rapidly. The plan is: Get 4 large instances that are compatible types with Placement Groups (as well as ideally, Enhanced Networking) (2 for web, 2 for DB.) We use an EBS-backed instances to store our operating system. Discussion here: http://alestic.com/2012/01/ec2-ebs-boot-recommended We can set up ephemeral SSD instance storage as swap space. (But it is lost after even a reboot. I hear its hard to add ephemeral storage if booting from EBS, but possible.) For offsite backup, we will take periodic snapshots and store them on S3. Obviously we need to ensure the database is in a safe state when that snapshot happens to avoid corruption. (Any hints here, aside from shutting down the DB?) If the database gets too big, we need to create a EBS volume that's larger. We can use RAID to break the 1 TB limit: http://alestic.com/2009/06/ec2-ebs-raid Static assets on web servers will be stored on S3. Is that correct? Or am I missing something?

  Read the article

< Previous Page | 606 607 608 609 610 611 612 613 614 615 616 617  | Next Page >