Search Results

Search found 7129 results on 286 pages for 'battery usage'.

Page 62/286 | < Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >

• ubuntu hardrive repartition without uninstalling ubuntu or windows 7 and losing data of hardrive

  - by user141692

  I have and asus r500v with 750 gb gpt system uefi motherboard core i7 3610qm, nvidia geforce gt, with ubuntu and w7 dual boot, I had problems installing ubuntu because of the grub but I fix it with https://bugs.launchpad.net/ubuntu/+source/grub2/+bug/807801, but I still have the problem of "warning: the partition is misaligned by 3072 bytes. this may result iin very poor performance. Repartitioning is suggested" in every linux partitioin I made and my 750 gb is not being used at the maximun capacity it only uses 698 gb. I want to make partitions so that the warning doesnt show up and I can use the maximum capacity of the HDD, as I did with another dual boot laptop (compaq presario cq40). I have the following partitions: unknown 1.0Mb: partition type: lynux Basic DAta partition, device: /dev/sda2 Usage: --, Partition flags: --, partition label:-- warning: the partition is misaligned by 3072 bytes. this may result in very poor performance. repartitioning is suggested. -system 210 Mb FAt, usage: Filesystem, partition type: EFI system Partition, Partition Flags:--, Label: system, Device: /dev/sda1, partition label: EFI system partition, Capacity 210MB, avilable:--, Mount Point: mounted at /boot/efi -134 Mb NTFS, usage: filesystem, partition type: linux basic data partition, partition flags:.--, device: /dev/sda7, partition label: --, capacity: 134MB,available:--, mount point: not mounted -OS 250 GB NTFS, usage: file system, partititon type: linux basic data partition, partition flags: --, type: NTFS, label: OS, device: /dev/sda3, partition label: basic data partition, capacity: 250 GB, available:-, mount point: not mounted -10GB FAT 32, usage: filesystem, partition type: EFI system partition, partition flags:--, type: FAT 32, label: --, device: /dev/sda4, partition label: --, capacity: 10GB, available:--, mount point: not mounted warning: the partition is misaligned by 3072 bytes. this may result in very poor performance. repartitioning is suggested. -10gb ext 4, usage: file system, partition type: linux basic data partition, partition flags:--, type: EXT4(version1) label:--, device: /dev/sda9, partition label:--, capacity: 10 GB, available:--, mount point at / warning: the partition is misaligned by 1536 bytes. this may result in very poor performance. repartitioning is suggested. -478GB ext4, usage: filesystem, partition type: linux basic data partition, partition flags:--, type: EXT4, label:--, device: /dev/sda5, partition label:--, capacity: 478gb, available:--, mount point: mounted at /home warning: the partition is misaligned by 512 bytes. this may result in very poor performance. repartitioning is suggested. -2.0gb Swap 2.0Gb, usage: swap space, partition type: linux swap partitioin, partition flags:-, device: /dev/sda6, partition label: capacity: 2.0gb warning: the partition is misaligned by 512 bytes. this may result in very poor performance. repartitioning is suggested. and as you can see it is not well organized so please help me to organize the partitions witahout uninstalling the w7, and if possible the grub2

  Read the article

• Bash scripting help

  - by paul

  #!/bin/bash usage() { echo "usage: ‘basename $0‘ project_name" } if [ $# -ne 1 ] then usage exit 1 fi mkdir $1 What does this code do?

  Read the article

• Single Responsibility Principle usage how can i call sub method correctly?

  - by Phsika

  i try to learn SOLID prencibles. i writed two type of code style. which one is : 1)Single Responsibility Principle_2.cs : if you look main program all instance generated from interface 1)Single Responsibility Principle_3.cs : if you look main program all instance genareted from normal class My question: which one is correct usage? which one can i prefer? namespace Single_Responsibility_Principle_2 { class Program { static void Main(string[] args) { IReportManager raporcu = new ReportManager(); IReport wordraporu = new WordRaporu(); raporcu.RaporHazirla(wordraporu, "data"); Console.ReadKey(); } } interface IReportManager { void RaporHazirla(IReport rapor, string bilgi); } class ReportManager : IReportManager { public void RaporHazirla(IReport rapor, string bilgi) { rapor.RaporYarat(bilgi); } } interface IReport { void RaporYarat(string bilgi); } class WordRaporu : IReport { public void RaporYarat(string bilgi) { Console.WriteLine("Word Raporu yaratildi:{0}",bilgi); } } class ExcellRaporu : IReport { public void RaporYarat(string bilgi) { Console.WriteLine("Excell raporu yaratildi:{0}",bilgi); } } class PdfRaporu : IReport { public void RaporYarat(string bilgi) { Console.WriteLine("pdf raporu yaratildi:{0}",bilgi); } } } Second 0ne all instance genareted from normal class namespace Single_Responsibility_Principle_3 { class Program { static void Main(string[] args) { WordRaporu word = new WordRaporu(); ReportManager manager = new ReportManager(); manager.RaporHazirla(word,"test"); } } interface IReportManager { void RaporHazirla(IReport rapor, string bilgi); } class ReportManager : IReportManager { public void RaporHazirla(IReport rapor, string bilgi) { rapor.RaporYarat(bilgi); } } interface IReport { void RaporYarat(string bilgi); } class WordRaporu : IReport { public void RaporYarat(string bilgi) { Console.WriteLine("Word Raporu yaratildi:{0}",bilgi); } } class ExcellRaporu : IReport { public void RaporYarat(string bilgi) { Console.WriteLine("Excell raporu yaratildi:{0}",bilgi); } } class PdfRaporu : IReport { public void RaporYarat(string bilgi) { Console.WriteLine("pdf raporu yaratildi:{0}",bilgi); } } }

  Read the article

• ASP.NET - What is the best way to block the application usage?

  - by Tufo

  Our clients must pay a monthly Fee... if they don't, what is the best way to block the asp.net software usage? Note: The application runs on the client own server, its not a SaaS app... My ideas are: Idea: Host a Web Service on the internet that the application will use to know if the client can use the software. Issue 1 - What happen if the client internet fails? Or the data center fails? Possible Answer: Make each web service access to send a key that is valid for 7 or 15 days, so each web service consult will enable the software to run more 7 or 15 days, this way the application will only be locked after 7 or 15 days without consulting our web servicee. Issue 2 - And if the client don't have or don't want to enable internet access to the application? Idea 2: Send a key monthly to the client. Issue - How to make a offline key? Possible Answer: Generate a Hash using the "limit" date, so each login try on software will compare the today hash with the key? Issue 2 - Where to store the key? Possible Answer: Database (not good, too easy to change), text file, registry, code file, assembly... Any opinion will be very appreciated!

  Read the article

• How to keep the CPU usage down while running an SDL program?

  - by budwiser

  I've done a very basic window with SDL and want to keep it running until I press the X on window. #include "SDL.h" const int SCREEN_WIDTH = 640; const int SCREEN_HEIGHT = 480; int main(int argc, char **argv) { SDL_Init( SDL_INIT_VIDEO ); SDL_Surface* screen = SDL_SetVideoMode( SCREEN_WIDTH, SCREEN_HEIGHT, 0, SDL_HWSURFACE | SDL_DOUBLEBUF ); SDL_WM_SetCaption( "SDL Test", 0 ); SDL_Event event; bool quit = false; while (quit != false) { if (SDL_PollEvent(&event)) { if (event.type == SDL_QUIT) { quit = true; } } SDL_Delay(80); } SDL_Quit(); return 0; } I tried adding SDL_Delay() at the end of the while-clause and it worked quite well. However, 80 ms seemed to be the highest value I could use to keep the program running smoothly and even then the CPU usage is about 15-20%. Is this the best way to do this and do I have to just live with the fact that it eats this much CPU already on this point?

  Read the article

• Can I monitor a service's memory/cpu usage on OpenSolaris?

  - by Phillip Oldham

  What would be the best way to monitor a service's memory/load on the OpenSolaris platform so that one can send alerts and automate service management (restarts, etc) based on "rules"? On the linux platform I use Monit, but since OpenSolaris has SMF I thought there may be a complimentary service "built-in" if SMF doesn't have those features and I'd prefer to use a standard OpenSolaris app if there is one.

  Read the article

• How can I limit my data usage over tethering on Windows?

  - by Casebash

  The excess data charges if I go over my tethering data limit are ridiculously. Fennec already stated the question well. Because of this, and on general principle, I'd like to have some tools which permit me to do things like: Monitor the amount of bandwidth that I've used I think I can do this from Sprint too, but on-the-computer is nice too on-the-computer gives me a possibility of breaking it down by application See what sort of programs are using the Internet connection I could use, like, Wireshark, but that's a bit too micro-level to be practical Keep those programs, and the operating system, from doing things like "downloading an operating system update" while on the mobile hotspot Related I want to monitor and limit OS X's data transfer while I'm tethering via my iPhone

  Read the article

• Should websites live in /var/ or /usr/ according to recommended usage?

  - by nbolton

  According to a guide on the Linux directory structure, /usr/ is for application files, and /var/ is for files that change (I assume this means "files that belong to the applications"). Is this correct? If this is the case then I'm a little torn between using either. A website is an application (if it's dynamic, so to speak), but in other cases it is just a collection of files used by Apache. The default www dir lives in /var/www/, so should we follow suit by using /var/websites/ (or something similar), or choose /usr/websites/ since they could be applications? This is a very trivial question, but it's bugging me nonetheless. For our case, I'm leaning toward /usr/web or something like that, since our websites are all applications. Update: This is for our company websites; it's not a shared hosting server, so we don't need to worry about separating them in /home/ or anything like that.

  Read the article

• Windows 7 boot problem on a Lenovo Thinkpad Z61m 9450HAG

  - by Matt Taylor

  Hello, I recently did a full upgrade of windows 7 on my thinkpad, everything worked fine after up until the second reboot (the first reboot after some updates installed worked OK). At second reboot time the system would just black screen just before the Windows logo appears, disk/wireless/power/battery lights are all lit and the disk light is active (flickering). However, if I remove my battery and boot with just power it boots fine and quickly, and everything is OK. Any help on why this wont boot with battery plugged in is greatly appreciated - i need to take this battery out on the road/trains etc.... Cheers Matt

  Read the article

• Dual boot OSX and Windows 7 natively

  - by Phill

  I'm considering getting one of those new fancy Mac Book Pro's with the fancy screens, but after reading some stuff on the internets about running Windows 7 with bootcamp: https://discussions.apple.com/thread/2770866?start=0&tstart=0 It seems you can't use the integrated graphics with windows, this causes windows to chew the battery life: I am afraid it is not possible. Since Apple introduced dual graphics chip laptops, they kept the low power/embedded GPU hidden under Window and they expose only the power hungry discrete GPU. It feels that this is being done on purpose so that it appears to users that OS X offers a better experience and battery life over Windows. So running bootcamp and windows kills the battery, running in parallels means you don't get accelerated 3d support (or something along those lines), so you don't get the performance out of it. I'm wondering: Is it possible to natively dual boot Windows 7 on a MBP, and if so would/does that give windows access to the integrated graphics to be able to not rape the battery?

  Read the article

• APC Smart UPS network shutdown issue

  - by Rob Clarke

  Here is a bit about our setup: We have 2x Smart-UPS RT 6000 XL units with network management cards We are running Powerchute from a network server Powerchute is connected to the management cards of both UPSs UPSs are set to do a graceful shutdown via Powerchute when the battery duration is under 20 minutes We also have a command file that runs with Powerchute Although our setup is redundant we do not have an equal load on each server due to APC switches for single power devices The problem is that as we do not have an equal load on each server the batteries drain at different rates. This means that the UPSs both get to the specified low battery duration at completely different times. The problem here is that UPS 1 may have run down to 5 minutes and is in desperate need of initiating a Powerchute shutdown - UPS 2 still has 25 minutes of runtime so no shutdown is initiated. Consequently UPS 1 goes down and takes all the servers with and then shuts down UPS 2 as well! What we need to happen are 1 of either 2 things: Powerchute initiates the shutdown as soon as either UPS reaches the 20 minutes low battery duration setting - and doesnt wait for both The UPS with the heavier load expends its entire battery but does not shutdown both UPSs and lets the load be switched across to the UPS that still has runtime remaining. That way when the UPS that still has runtime reaches its low battery duration it can proceed with the graceful shutdown via Powerchute. Hope that makes sense, any help is greatly appreciated!

  Read the article

• APC Smart UPS network shutdown issue

  - by Rob Clarke

  Here is a bit about our setup: We have 2x Smart-UPS RT 6000 XL units with network management cards We are running Powerchute from a network server Powerchute is connected to the management cards of both UPSs UPSs are set to do a graceful shutdown via Powerchute when the battery duration is under 20 minutes We also have a command file that runs with Powerchute Although our setup is redundant we do not have an equal load on each server due to APC switches for single power devices The problem is that as we do not have an equal load on each server the batteries drain at different rates. This means that the UPSs both get to the specified low battery duration at completely different times. The problem here is that UPS 1 may have run down to 5 minutes and is in desperate need of initiating a Powerchute shutdown - UPS 2 still has 25 minutes of runtime so no shutdown is initiated. Consequently UPS 1 goes down and takes all the servers with and then shuts down UPS 2 as well! What we need to happen are 1 of either 2 things: Powerchute initiates the shutdown as soon as either UPS reaches the 20 minutes low battery duration setting - and doesnt wait for both The UPS with the heavier load expends its entire battery but does not shutdown both UPSs and lets the load be switched across to the UPS that still has runtime remaining. That way when the UPS that still has runtime reaches its low battery duration it can proceed with the graceful shutdown via Powerchute. Hope that makes sense, any help is greatly appreciated!

  Read the article

• How can I get a data usage/access log for an external hard-drive?

  - by Vittorio Vittori

  Hello, I'm working in an office with many people and sometimes I leave my external hard drive with my personal data inside. I would to know if there is some way to see if my hard disk was used during my absence. I'm not the computer administrator, so I can't use exclusive file permissions and I would really like to know hard disk is opened from another computer. I am using a Mac. Does exist some other way to protect personal data on usb device like an hard-drive? If yes can you write some link to possible guides? I hope there is some ploy!!

  Read the article

• Excessive server I/O rate is a symptom of excessive memory usage?

  - by johnlai2004

  I'm learning to manage a VPS LAMP server. I noticed that whenever Apache consumes more RAM than is allotted, the server disk I/O rate jumps from a negligible value to a big value like 3k/hour. Why is this so? What exactly is happening? Thanks

  Read the article

• Reseting Macbook Pro keyboard and trackpad's power usage on Windows?

  - by Dan the Man

  I recently installed a utitlity for Windows (ASUS Ai Charger) which modifies the USB ports on the computer to output more power (for charging iPads, etc). The problem is, I believe it is also giving more power to my keyboard and trackpad. And now, neither devices are working at all, yet they work on Mac OS X. So does anyone know the amount of power MacBook Pro (2007) keyboards and trackpads use, and how I can set these settings in Windows 7?

  Read the article

• Windows 7 Wakeup from Sleep then Shutdown

  - by Kevin Hua

  Is this caused by low battery? I have an Asus UX31A, and I left it unattended. As usual, in 5 minutes, it went to sleep mode with the lid still open. I came back a couple hours later, and I noticed the laptop was off. I was still able to turn it on by manually pressing the power button (battery was at 2% though), but I don't understand why it shut off. If it was in sleep mode and the battery was near depletion, then wouldn't that result in a "Windows has recovered from an unexpected shutdown" upon boot? Does Windows have a mechanism to wake from sleep from a super critical battery level to shut down all programs and power down the system completely? I noticed that upon booting, firefox didn't give a fit about improper shutdown. Here are my power settings btw, powercfg -h off has been ran, so hibernation is off. And here is the event log: http://www.mediafire.com/download.php?lbfhl21g0nj2adi

  Read the article

• Hard drive degredation from large memory usage and paging files?

  - by Stephen R

  I've had a question(s) regarding computer degradation going through my head for a while and haven't found many good resources for researching it. 1) First off, when is the virtual RAM/paging file on a hard drive used by Windows? Is it used when the RAM is full? Or does it use the Virtual RAM/paging file as intermediate caching between the RAM and actual hard drive space all the time? 2) If I were to run many applications on my computer at the same time and have a bad habit of doing this for the entire lifetime of the computer, does it use more of the virtual RAM/paging file than if I were to have fewer programs running? Just to note, the RAM never fills up on my computer but it is used heavily. 3) By extension of question 2, if the virtual RAM/paging file is used more heavily, would that result in rapid hard drive degradation? I have seen a pattern among all of the computers that I have owned or used in the past 5 years. I am the kind of person to leave my web browser up with 40 tabs among other programs which will eat up 40% of my memory typically. Over time my computer will slow down, browsers start crashing, programs start seizing up or crashing themselves, eventually the computer becomes essentially unusable. I have been trying to rack my mind to come up with a solution other than to purchase a new PC to have it die on me in the next couple years as well. This is the only thought that has come to mind that might have a simple hardware fix...Windows ReadyBoost...Maybe? I'd like to be able to discuss this so I can learn something about all of the above. Thanks.

  Read the article

• Collecting and viewing statistical data on website usage? Want to give Google Analytics the boot.

  - by amn

  I have always been somewhat reluctant to "outsource" site statistics to Google. We have an Apache server running on a Windows server. I am pretty sure all the foundation to collect the needed visitor data are there. I would like to stop using GA, and use some form of application where the data does not travel to a third party but remains at the host, or at least travels to the remote administrator, if it is a log analyzer in a browser. What are my options?

  Read the article

• Are some DSL modems cheaper to operate than others? (power usage question)

  - by SetJmp

  I recently have started using a Motorola 2210 in conjunction with AT&T's DSL service in the Silicon Valley area. That gadget runs hot to the touch! Which means... I assume it is gobbling lots of electricity even when I am not using it. Has anyone studied this subject in a rigorous way? Which leads to the question... if the 2210 is very energy inefficient are some DSL modem models cheaper to operate than others? -SetJmp

  Read the article

• Flash Backed Write Cache (FBWC) without capacitor pack

  - by Martyn

  I brought a HP Smart Array P410 controller and it is installed and working fine in a HP Prolient Microserver with 4 drives in two RAID 1 arrays. I didn’t realise however that it came without any cache so would only work by directly writing straight to the disk, and the performance was horrible. So I then brought the 512MB Flash Backed Write Cache (FBWC) memory module as I was under the impression that with FBWC I would not need a battery. I got this idea from a forum post. "What do you guys think of the choice between 'BBWC' (battery backed write cache) and 'FBWC' (flash backed write cache)? The flashed based ones use non-volitile memory so need no battery." After installing the cache module however the server pretty much won’t boot. The P410 has a flashing amber light on it, and from the manual that doesn’t sound good. I’ve managed to get to the on board BIOS once and even managed to get to boot to the HP Array Configuration Utility (ACU) CD once, but every other time the Server continuingly reboots once it get to the POST screen and reads ARRAY INITILIZING %%%. The one time I reached the ACU, it reported a problem with the Cache Module. To me, it seems like the cache module is faulty, however the supplier tells me “Do you have an FBWC battery pack, p/n 587324-001, because that is required for the cache to work. If you have it, please complete an RMA form and we'll send a replacement / credit.” Does this sound right to you? I’ve been ordering the parts from the US and I don’t want to spend $77 + $40 p&p on a battery, wait a week for the shipping to find the card is faulty, and I don’t want to send back a working card?

  Read the article

• How do I lower idle cpu usage in ubuntu linux? Gnome or KDE Variants

  - by Jasen

  My question comes from a kde desktop currently, but it also happens with the gnome instance. When just sitting there, with only the cpu monitor widget running. no open windows, no background processes other than the desktop, my cpu is at ~20%. I wanna know how to fix this, and possibly get better performance out of it. When running my windows side, the cpu will sit at zero, and i generally load new programs about 400ms faster. With windows 7 being as slow as it is, this is not acceptable. and the widget is only set to check every 500ms, so im almost completely sure its not the widget. My system is a Gateway nv 53 amd 2.0 ghz turion with 4 gb of installed ram, and 500 gb hd. both linux and windows are 64 bit. average ram use on either system is about 1.4 gb for just the os

  Read the article

• How can I compare effective power usage of two CPUs / CPU+Mobo+Mem combinations?

  - by einpoklum

  I have this server which does mostly file sharing (with the associated storage). No serious number crunching and it isn't the firewall. My current box has a Celeron D processor (Prescott 336 2.8 GHz); and I'm considering replacing it with a Pentium D (Smithfield 805 2.66 GHz) - for reasons which do not involve performance. How can I know whether one can expect a higher or lower power consumptipn for the change? And how can I estimate the power consumption for each option?

  Read the article

• How to calculate required switch speed based on network usage?

  - by tobefound

  I have a 48 port HP Procurve Switch 2610 (J9088A) that can handle 13.0 million PPS (packets per second) and features wire speed switching capacity at 17.6Gbps. First off, what does that REALLY mean? Where do I start when trying to figure out if my office (with 70 employees) will be well setup with this switch? How to calculate through-put based on a user average load of X MB per day? 90% of the folks will only be sending email, access random websites, etc... the other 10% will be conducting heavier tasks like moving image files (10 MB) across network shares, constant external FTP streams through the switch to a server etc... Is this switch good enough?

  Read the article

• Startech SVx41HDI Series Server Remote Control Usage Question - How do I switch away from a dead por

  - by tajh

  We have a Startech KVM over IP model SV841HDI and it was stuck pointing a port where the machine has been removed. We ended up having to physically plug something into that port in order to switch ports again, meaning that if someone in support accidentally switches to an empty port, we need to have a documented solution for making it useable again. The unit is old, no longer under warranty, firmware updates for it are no longer available (interestingly it runs a powerPC version of busybox). Since it does work well except for this one catch, we would like to avoid replacing it. Reading the manual, you have a several recommended methods. I tried them. Hit the left CTRL key a few times (as well as all the other popular KVM keys I could think of). The VNC GUI offers lots of buttons - none of them switch away from a dead port. The question is: how do I switch away from a dead port on this particular KVM remotely?

  Read the article

• Does Intel Smart Response provide any statistics on the cache usage?

  - by Tom Seddon

  I've set up my Z68-based Core i7 PC with a 60GB SSD dedicated as a Smart Response cache drive. Is there any way I can get any statistics out of it? It would be nice to have some information on how much cache space is actually being used, maybe how much of it was actually accessed recently, and how many reads in general are coming from the SSD rather than from the mechanical disk. These statistics might help to quickly provide some evidence for or against the use of Smart Response, without my having to reinstall Windows on the SSD (etc.) to find out. The Windows ReadyBoost feature has some performance counters you can access via the Windows 7 perfmon tool, for example, which is the kind of thing I'm hoping is somehow available. Smart Response provides no perfmon counters, though, and the Intel Rapid Storage Utility tells you pretty much nothing except that Smart Response is switched on.

  Read the article

< Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >