Search Results

Search found 1863 results on 75 pages for 'clone of anton makrushin'.

Page 62/75 | < Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >

• Cloning a NAS drive which hosts a SQL Server DB

  - by Adrian Hand

  We have a system in the field running a server application which is suffering with major performance issues. The system in question has 2 onboard 300gb sas drives in RAID 5 from which it boots Windows Server 2003, and a 6tb buffalo terastation NAS unit (also RAID 5) to which the server app does all of its reading and writing. I believe the terastation is the source of all our woes. Whilst under load, reads and writes tick by at something of the order of 1meg/sec, though the network in question is hardly utilised. The terastation contains various data, but crucially hosts a full instance worth of SQL Server .mdf and .ldf files (master etc - the whole shooting match) I wish to stop all the services on the server, then take everything on the terastation and essentially clone it to some alternative onboard storage, so as to eliminate the terastation from the equation as far as poor performance is concerned. ie the terastation is currently drive D: - I want to copy everything off and then have the duplicate assume the drive letter so that as far as the software is aware, nothing is different. This is tricky because of the mdf and ldf files - everything else will work with a straight up file copy. Can anyone suggest a means to achieve what I am describing? Many thanks!

  Read the article

• Data Store/Volume disconnecting. How to resume copy of VMDK?

  - by Serge

  I'm having an issue with my ESXi 4.1 hosts losing the datastore with FC SAN after a power outage. All 3 hosts disconnect so it's definitely a SAN issue. I've tried to resolve the issue on the SAN side with the SAN software support and Adaptec hardware support. No luck there. So I'm stuck with a SAN that will randomly disconnect the volume. I need to get the virtual machines (VMDK files) from the datastore. The problem is I can only get 5-20% before the data store disconnects. I have backups that are slightly older that I can use to replicate the VMDK differences to. What has not worked so far: Powering up the VMs, will boot up for 5-15 minutes then freeze vCenter migrate or clone of VM, will fail after similar period of time vCenter copy/paste of VMDK. Was able to get one 30GB VMDK and no luck after that. vMware Data Recovery. Fails at low %, can't resume, so next backup starts from begining. Veeam Backup & Recovery. Same as above, no resume function. If I can just find a backup solution that will resume from the failed spot that would solve my issue. Anyone have any ideas that I could try? EDIT 1 The SAN is Open-E DSS 6 running on a Supermicro 24 drive enclosure with 4 port Qlogic FC. Adaptec 52445 RAID card.

  Read the article

• Applications randomly alt-tab? (especially full screen games)

  - by Henry Scotts

  I'm not sure when this began, how it happens, or why it happens, but it is quite bothersome and apparently random. Just randomly throughout the day my computer will just go to the desktop. I could be in a full screen game and it will just immediately alt tab and present the desktop. Or I could be watching a movie and this happens. Sometimes it happens once every three hours and other times (just today actually) it did it twice in the span of 30 seconds. I am positive I am not pressing a hotkey because I launched a game, sat idle, and noticed it alt tab while cleaning up around my room after about 20 minutes. Sometimes it goes days without this happening. Specs: Windows 7 Ultimate 64 Bit, 10 gigs of RAM, GeForce GTX 260, Intel Xeon CPU. I also have basically nothing running when it happens other than the game and FireFox. My FireFox add-ons: Adblock Plus, Download Statusbar, Firebug, FirePHP, lazarus form recovery, tree-style-tabs, yslow. I doubt FireFox is causing the issue but I figured I'd include it anyway because it is the only application I have running when it happens. As for user processes I have running: VCDDaemon (context menu for virtual clone drive), razerhid (mouse), OSD, taskhost, dmw (desktop window manager), anyfullscreengame, audiorepeater, netsession_win, explorer, razerofa, tsvncache, firefox, plugin-container, and EKIJ5000MUI (printer). Whew. Okay. That was a lot of information. If someone could diagnose this I would be most grateful for this has been around with me for years.. Thanks for reading! PS: I doubt it's a virus because I never download illegal software and pretty much only browse Reddit and Stackexchange and play games. If it was a virus it would be a pretty lame one.. Hah..

  Read the article

• correct file permissions for trac and git user to access gitolite server repos

  - by klemens

  hi, sounds like a stupid questions (to me), but i couldn't find any info. on my server i host some git repositories via gitolite, and have a trac for every repository. i have a user called git to push/pull from server (git clone git@server:repo). and trac is a apache vhost with mod_wsgi. this runs with the www-data user. so what riddles me (maybe because I have not much of a clue about file-permissions at all) is whats the best permissions setup (chown, chmod) for the git repositories (/home/git/repositories/...). www-data (or trac) needs to at least read permissions (i think). and git (or gitolite) needs obviously read/write permissions to push changesets. i tried a little bit around (i.e. adding www-data and/or git to the www-data/git group), but didn't got it right. at least one of the two don't work (git or trac). any suggestions are highly appreciated. regard, klemens

  Read the article

• Recovering a mdadm+lvm+ext4 partition with read error

  - by bitwelder

  One of disks in my NAS has failed. The NAS is running Linux, and it uses mdadm + LVM technology for its filesystems. I do have backup for most of the contents, but not for the very last changes, and if possible, I'd like to recover that from this failing disk. The disk (a 'green drive' WD10EARS 1TB in size) throws this kind of errors: Oct 3 12:00:41 kernel: [ 3625.620000] ata5.00: read unc at 9453282 Oct 3 12:00:41 kernel: [ 3625.620000] lba 9453282 start 9453280 end 1953511007 Oct 3 12:00:41 kernel: [ 3625.620000] sde5 auto_remap 0 Oct 3 12:00:41 kernel: [ 3625.630000] ata5.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 Oct 3 12:00:41 kernel: [ 3625.630000] ata5.00: edma_err_cause=00000084 pp_flags=00000003, dev error, EDMA self-disable Oct 3 12:00:41 kernel: [ 3625.640000] ata5.00: failed command: READ FPDMA QUEUED Oct 3 12:00:41 kernel: [ 3625.650000] ata5.00: cmd 60/40:00:e0:3e:90/00:00:00:00:00/40 tag 0 ncq 32768 in Oct 3 12:00:41 kernel: [ 3625.650000] res 41/40:00:e2:3e:90/12:00:00:00:00/40 Emask 0x409 (media error) <F> Oct 3 12:00:41 kernel: [ 3625.660000] ata5.00: status: { DRDY ERR } However, while testing with 'dd', I noticed that if I skip the first 4kB, the read seems to be ok, i.e. a command like. dd if=/dev/sde5 of=dev/null bs=4k count=1000 skip=1 doesn't return any read error. Supposing that there is no other read failure in the rest of the disk, would I be able to recover this 900 GB partition (as I mentioned before, it's a 'linux raid autodetect' partition, that contains a a LVM2 volume that contains a ext4 filesystem) if I copy-clone the partition somewhere else, but the first 4kB?

  Read the article

• What are the IR codes the new Apple Remote (alu) uses?

  - by index

  I would like to clone the new Apple Remote (infrared, second generation, aluminium) just for fun with a microcontroller. Most codes of the previous model can be found in the LIRC remote control database (all except the key combinations menu + <<,play, which unpair, change ID, pair the remote. I also don't know which bit encodes the battery status. It uses a modified 32 bit NEC protocol (reverse LIRC codes bytewise). But the new Apple remote uses two additional codes for the play and the new select button. I don't have a mac, so I can't brute force test codes either ;-) So if someone possesses such a remote and the ability of recording those two new buttons and three combinations I'd really appreciate it. If you can't run LIRC (or it gets confused by the new codes) and you don't have an oscilloscope or logic analyser, maybe you could hook up a photo diode to your sound input and record the codes with Audacity? Just hit record, hit each button and combo a few times, hit stop, upload the uncompressed WAV file to a sharing site, done. That'd be great!

  Read the article

• Internet in the router but not in the local network.

  - by TheMouse

  I have a PC and a laptop (Windows 7 - both) which should connect through router to Internet. The router is Linksys wrt120. My ISP is using PPPoE. I have connected the Internet cable to the router, clone the MAC of my PC, writing the username and the password for my Internet connection. After seconds the router has acquired IP from my ISP. I have used the administration panel of Linksys and with the help of the ping and tracert commands which are built into it - I can connect to the world, outside the network. The problem is when I try to connect the PC or the laptop to the network. There's no problem here. The DHCP server of the router gives them appropriate addresses. The problem is that they couldn't connect to either Internet addresses (google.com) or IP addresses. But they can connect to the router and its control panel. I tried several times, reset the router..but there's no Internet..still.

  Read the article

• Multiple servers vs 1 big server performace

  - by pistacchio

  Hi to all! My team of developers has suggested a server structure for an upcoming project we are developing. Our structure is "logical", meaning that the various logical components of the application (it is a distributed one) relies on different servers. Some components are more critical than others and will be subjected to more load. Our proposal was to have 1 server per component but the hardware guys suggested to replace the various machines with a single, bigger one with virtual servers. They're gonna use Blade Servers. Now, I'm not an expert at all, but my question to the guys was: so if we need, for example, 3 2GHz CPU / 2GB RAM machines and you give me 1 machine with 3 2GHz CPUs and 6 GB of RAM it is the same? They told me it is. Is this accurate? What are the advantages or disadvantages of both the solutions? What are the generally accepted best practices? Could you point out some URL reference dealing with the problem? Thank you in advance! EDIT: Some more info. The (internet / intranet) application is already layered. We have some servers on the DMZ that will expose pages to the internet and the databases are on their own machines. What we want to split (and they want to join) are some webservers that mainly expose webservices. One is a DAL that communicates with the database layer, one is our Single Sign On / User Profile application that gets called once per page and one is a clone of what seen on the Internet to be used on our lan.

  Read the article

• Virtualize SBS 2003 - P2V vs migrating to new VM

  - by jlehtinen

  I need to virtualize a SBS 2003 server in my work environment. I need some tips on what people think is the best way to proceed. Background: The SBS 2003 server is the primary DC for the domain and also hosts FTP, RRAS(VPN), DNS, and file shares. Exchange is NOT used, neither is SQL server. DHCP is done via a firewall appliance. I have added a Server 2003 VM to the domain and promoted it to the DC role. AD/DNS is replicating here correctly. This was mainly done to provide fault-tolerance to the domain, I was not intending to make this VM the primary DC. I've already asked about buying upgraded licensing for Server 2008/2012 but was refused due to cost. Options: I see (at least) two routes I could take to complete this. From what I've read option 2 is the "preferred" method, but there's a few steps where I'm not clear on what to expect. Option 1.) P2V the primary DC Power off primary DC Power off secondary DC (to prevent USN rollback in case P2V has issue) P2V (cold clone) primary DC Boot new PDC VM Allow new hardware to detect Remove old NIC hardware from device manager Assign old IPs to new virtual NICs Reboot PDC VM, confirm connectivity and no major issues Power on secondary DC, confirm replication Option 2.) Create new VM, transfer roles, remove original DC from domain Create new VM, install SBS 2003 Do I need the original SBS install discs for this? MS migration doc mentions this. Add VM to domain, promote to DC role Does this start 7 day timer where two SBS servers can be in same domain? Set up RRAS on new VM Set up IIS/FTP on new VM Move file shares to new VM Transfer FSMO roles to new VM DC dcpromo original primary DC out of domain

  Read the article

• Does migrating 2 domain controllers between 2 datacentre requires both virtual machines to be shut down at the same time?

  - by Imagineer

  I was attempting to migrate 2 virtual machines that are domain controllers between 2 datacentres running ESX 3.5 and ESX 4.1. I was advised to shut down both domain controller at the same time during the migration process. This is to avoid USN Rollback and other replication issues. The following are the steps that I was planning to perform: 1. Shutdown both DC. 2. Copy both VMs files across to new datacentre using Veeam FastSCP (connection to both vCentre through IP address instead of hostname) 3. Power them up at new datacentre. 4. Configure Network interface/DNS/DHCP for both DCs in new datacentre I have tried to use Veeam FastSCP rather than VMware Standalone Converter is because its copying rather than converting. Someone also suggested that I use backup and restore app like Veeam backup and replication software. Sounds like a simple job, but after shutting down both DCs, the transfer rate using FastSCP is so slow registering only 1KB/s as oppose to the normal 1MB/s (or more). When that attempt to transfer failed, I tried to cold clone both DCs resulted in the both ESX hosts get disconnected. I have tried troubleshooting by referring to this - VMware KB - Diagnosing an ESX Server that is Disconnected or Not Responding in VirtualCenter It seems that the DNS being down is the caused of all unusual occurrence. The moment I powered up the DCs via VMware console command, the ESX host were able to connect to the vCentre again. How can I avoid such a pitfall again? Am I doing it correctly? Any help would be greatly appreciated! Thank you.

  Read the article

• How to migrate WinXP from failing old HD to new one

  - by Péter Török

  Following this issue, we have all our important data backed up now. I also bought and installed a new replacement hard disk (WD 160GB PATA) as secondary (slave) drive. I created two primary NTFS partitions on it: a 40 GB system partition, and a 110GB data partition. In theory I could start reinstalling WinXP from scratch on the new system partition, then copying over all user data from the old drive to the new data partition. Once this is done, I could even throw away the old drive, or keep it just to see what happens. (Note: I don't want to clone the whole drive as it contains a dual boot setup with an old Linux installation which I don't need anymore, and anyway, a fresh reinstall would do WinXP good to get rid of many years' clutter.) However, I am lazy :-) The old HD is still functioning, the problem has not manifested again since. So I feel there is no need to hurry with a complete OS reinstall. What I don't know though is whether I will be able to install WinXP on the new system partition at a later stage without affecting the contents of the data partition on the same drive. If this is possible, I can just move over all our data to the new data partition to have it safe, then continue running WinXP from the old drive as long as it works. Does anyone see any problems/risks with this plan?

  Read the article

• How to recover my invisible HD again?

  - by pattulus

  I made this several times now, but this time something bad happened. What I did: I installed Windows 7 at a 32GB partition on my slot 2 HD in my MacPro. Windows 7 made a 105MB partition… I knew this before, but what I didn’t know was that this partition is now on my slot 4 HD. My home folder, my private videos and some other stuff are on this 1TB drive. What I found out so far: I’m currently logged in as another admin since my OS partition as well as the two other HD's aren't harmed. Disk Utility: … only shows the 105MB NTSF partition on this 1TB volume. It isn’t showing my old 1TB partition/ex-HD named "storehouse". Only the partition tab is telling me that there now is a 1TB empty free unpartitioned space. Data Rescue II: … is showing the Volume as it used to be with it's old Name "storehouse". A quick scan and a thorough scan both were done in 1 second which leds me to the conclusion that there's isn’t something deleted at all (» hope!). Data Rescue doesn’t even mention the damn "system reserved" partition. Drive Genius: … also shows the old partition and doesn’t mention the new one. But looking at the info it tells me under "content": FDisk_partition_scheme (instead of Apple_partition_scheme). Well D'oh…. Tech Tools: … doesn’t show the volume, otherwise I'd might have been tempted to press rebuild/repair. What to do next?? I think the best approach is to buy another 1TB HD and let Disk Warrior Clone my old one to it… just to be on the safe side. But what is the best thing to do after this… ???

  Read the article

• OS X won't boot up unless I hold down option key

  - by Gazzer

  I have a strange issue on an early 2008 Mac Pro running OS 10.6: if I restart the computer it restarts normally if I shutdown and boot, it stops at the grey screen just before the boot process if I shutdown and boot but hold down the option key, I can select the boot disk and all is good. I've just cloned the disk, and the same thing happens. The disk is a SAMSUNG HD154UI The disk is partitioned (the second partition holds a clone of the Snow Leopard Install disk) One weird thing on the original disk was one of the partitions said 'EFI Boot' in a non-aliased font rather than the name of the disk when the disks are listed upon holding down option. Solution: it seems that there was a problem with the disk. Part of the difficulty in finding the solution was that you need to remove the disk from the computer completely. For example, a good disk in Bay 3, wouldn't boot up if the bad disk was in Bay 2. So for ages I thought the problem was hardware related in Bay 3. So if you think you have a dodgy disk remove it totally if you are testing the hardware with a 'clean' disk. Cleaning the PRAM helped to get the new disk to work too.

  Read the article

• ownership of hard drive recoveery of files Windows 7

  - by Jeff

  Here is the issue. I have an old laptop that died that was running xp. I now have a win 7 laptop. I need to get the files off the old drive. Win 7 will not let me take ownership of the drive. I can runn the comand prompt in regular mode and do a dir on the drive that shows up as Q: drive in regular mode. I gives me the volume as c and the serial number. I can not take ownership in regular mode with the comand prompt or other means. Microsoft site says use safe mode with networking. So I go to safe mode the drive shows up as G: in safe mode. I use the comand prompt Takeown /f G: and get the device is not ready error. I am at a loss. All I want is to retrieve my files from this drive. Any ideas or sugestions. I don't see how you can dir and get some info in one mode and not acces it in another. I have to get ownership and permissions fixed to get in the drive to get my files. Thanks in advance. I might add that I am using a usb3.0 to ide/sata cable adapter. Software came with the device but I can't make heads or tails out of the manual to know if any of the software can help me. The soft ware is PCClone Ex lite, and Clone Drive Soft ware

  Read the article

• Dead Linux server - need help and options

  - by Choi S.

  All, I have a Dell PE 1950 w/ 2 SATA drives in a software RAID1. OS is CentOS 5.5 (2.6.18.x). Starting this afternoon we received HW errors (something on the bus is bad, E171F) and the machine became unresponsive. We hard booted and it came back up for about 5 hours but then it happened again. I'm trying to figure out our options. Unfortunately we do not have similar hardware but I have a small desktop that I can use. I was contemplating putting one of the drives into the desktop and then starting it up. My goal was to then P2V it using Vmware converter but apparently the free v5.x doesn't support hot cloning/converting on a RAID volume, only the Enterprise 4.x version of Converter does. My questions are: 1.) Is putting a single drive out of a RAID1 pair into another piece of HW is safe? Based on my research and understanding it appears to be but would like confirmation. 2.) Is there any work around to the Vmware Converter not supporting RAID volumes during a hot clone/convert session? 3.) Are there other options I'm overlooking? Thanks in advance for reading and responding. --Choi S.

  Read the article

• How to connect computers to a network printer behind a router?

  - by kokbira

  General question: How to connect computers to an IP printer behind a router? Particular question: How to connect C-1 and C-2 to PRI? What? Where? [ISP] | | -> IPs:200.X.X.X/other configs:DC | [R-1] | | -> IPs:10.1.X.X locked by MAC,M:255.0.0.0,G:10.1.0.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [PRI] IP:10.1.7.7 [R-2] IP: 10.1.0.1,MAC:A | | -> IPs:192.168.1.X,M:255.255.255.0,G:192.168.1.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [C-1] IP:192.168.1.2 [C-2] IP:192.168.1.3,MAC:A Glossary and details: ------------------------------------------------------------------------------------ - IP: IP. - IPs: Some IP range. - M: Mask. - G: Gateway. - MAC:A: A MAC address that I will not inform you :) - DC: Don't care. - ISP: Internet Service Provider (not so much details about it on that case). - R-1: A real router or some concatenated so IP range bellow that block is 10.1.X.X and above is ISP. The provided IPs are provided by MAC. As all available addresses are in use, you must clone an existing one to join with a new device (and to disconnect the cloned one). - PRI: An network printer (some people here call that IP printer). - R-2: A TP-LINK TL-WR340G, mine wireless router (since my computer does not have ethernet input, it is my ethernet-wifi adapter :), admin access, MAC address cloned from C-2 (MAC:A). I've to configure 10.0.1.1 and 10.0.1.2 as DNS addresses, other wise I cannot connect C-1 and C-2 to Internet. - C-1: My computer, a CCE XLE-425 (remember: no ethernet input), with Windows 7, admin access. - C-2: another computer with better configs than mine, MAC:A, Windows XP. Requirements: I want to print, to access Internet and to do it myself (no need to call network admin men in black people). Pay attention to MAC clones and DNS info.

  Read the article

• Can't start Windows 7 after cloning HDD

  - by Paul

  Brief description: cloned HDD1 - HDD2 HDD1 partition 1 boots HDD1 partition 2 boots HDD2 partition 1 boots HDD2 partition 2 doesn't boot Windows, but is bootable in general Now verbosely: In all the cases computer is the same. I have two Windows 7 installations on HDD1 - both are booting fine. I choose between them using standard Windows 7 boot loader menu. Technically there are 4 partitions: 100 MB Boot loader partition (active), Windows 7 copy 1 (25 GB), Windows 7 copy 2 (150 GB) and Working partition. All are primary. In past few days I tried to clone the whole HDD1 to HDD2 of the same size (but 2,5 inch form factor) as is using Minitool Partition wizard. Everything has been copied, all files are accessible, no faults in file system structure, even boot loader wasn't damaged and I hadn't to repair it. But I can boot only first installation of Windows 7 (it boots without issues). When I choose the second installation, I get immediately a completely black screen without any texts, cursors and other data. HDD isn't accessed after that. This black screen is sensitive to Ctrl-Alt-Delete which causes computer reboot. I did some experimenting: Installed Windows 7 to that partition - it booted fine. Then I renamed "Windows" to "Windows.old" and copied Windows directory from HDD1 as it was, using Far Manager, and got the same troubles - black screen. (Of course I performed renaming and copying from other copy of Windows). So, it seems that problems are inside this installation of Windows, somewhere in its files.

  Read the article

• Error authenticating git repository with Redmine

  - by woni

  I've setup Redmine 2.1 on my Debian Squeeze server following this Tutorial HowTo configure Redmine for advanced git integration (I tried to use the grack path). Redmine server is running properly, but I have a problem granting users access to git repositories. When I try to clone a repository it says: error: The requested URL returned error: 500 while accessing The apache error.log shows this entry: [Fri Sep 28 15:50:56 2012] [crit] [client xx.xx.xx.xx] configuration error: couldn't check user. Check your authn provider!: /repo.git/info/refs It also asks me for user and password when cloning, but it shouldn't if I understand the tutorial right. I'm using the Redmine authentication module: <VirtualHost *:80> ServerName my.server.at DocumentRoot "/var/www/my.server.at/public" PerlLoadModule Apache::Redmine <Directory "/var/www/my.server.at/public"> Options None AllowOverride None Order allow,deny Allow from all </Directory> SetEnv REMOTE_USER=$REDIRECT_REMOTE_USER" SetEnv GIT_PROJECT_ROOT /var/git/my.server.at/ SetEnv GIT_HTTP_EXPORT_ALL ScriptAlias /git/ /usr/lib/git-core/git-http-backend <Location /> Order allow,deny Allow from all AuthType Basic AuthName Git Require valid-user AuthBasicAuthoritative Off AuthUserFile /dev/null AuthGroupFile /dev/null PerlAccessHandler Apache::Authn::Redmine::access_handler PerlAuthenHandler Apache::Authn::Redmine::authen_handler RedmineDSN "DBI:mysql:database=redmine;host=localhost" RedmineDbUser "user" RedmineDbPass "password" RedmineGitSmartHttp yes </Location> </VirtualHost> Can someone help me please and explain the error and what I can do to solve my problem?

  Read the article

• Cloning a git repository from a machine running OS X

  - by Mike

  Hi folks, I'm trying to host a git repository from my home OS X machine, and I'm stuck on the last step of cloning the repository from a remote system. Here's what I've done so far: On the OS X (10.6.6) machine (heretofore dubbed the "server") I created a new admin user Logged into the new user's account Installed git Created an empty git repository via "git init" Turned on remote login Set port mapping on my router (airport extreme) to send ssh traffic to the server Added a ".ssh" directory to the user's home directory From the remote machine (also an OS X 10.6.6 machine), I sent that machine's public key to the server using scp and the login credentials of the user created in step 1 To test that the server would use the remote machine's public key, I ssh'd to the server using the username of the user created in step 1 and indeed was able to connect successfully without being asked for a password I installed git on the remote machine From the remote machine I attempted to "git clone ssh://[email protected]:myrepo" (where "user", "my.server.address", and "myrepo" are all replaced by the actual username, server address and repo folder name, respectively) However, every time I try the command in step 11, I get asked to confirm the server's RSA fingerprint, then I'm asked for a password, but the password for the user I set up for that machine never works. Any advice on how to make this work would be greatly appreciated!

  Read the article

• Looking for advice on using dd to backup a dual boot laptop.

  - by AvatarOfChronos

  My questions boils down to this. If I do "dd if=/dev/sda of=usbdrive" can anybody confirm that this will get everything including mbr/partition information/all four partitions and create a drive that I can swap with the failing internal drive without losing anything? If this is done while the computer is running will it still copy everything? At this point I'm afraid to shutdown the computer for fear of it never starting again. Secondly, how tolerant is dd of failing drives? Has anybody used it to recover a half dead drive before that can share any potential pitfalls? Did it get the data ok or is this going to be a hope for the best kind of situation? And lastly, If the usbdrive is larger than the failing internal drive I'll still be able to expand the partitions later so I'm not losing space? this last part seems silly to ask but with my current streak of bad luck I'll end up overwriting some magic bit and forever turning a 640gb hdd into a 500gb hdd. Also if anybody has a better solution to create a complete clone that gets everything I'm all for hearing about it. PostScript: I had been making periodic backups however when whatever miasma that killed the laptop struck it also got the NAS :( Post PostScript: both devices were on a UPS system.

  Read the article

• Linux RAID: Replacing Failed Drive...permanantly

  - by user137519

  Okay, odd question here. I have a server with RAID 5. A drive failed, in a really physically in a really odd way. On the machine it boots and is seen by the BIOS but...no partition can be seen on the drive consistantly (in and out). 2 out of 3 drives working...I made new spare disk and added it, RAID 5 rebuilt clean. All appears well but...when I reboot it keeps trying to use the 2nd drive which doesn't give any partition data, so of course the RAID 5 gets 2 out of 3...again. The status of my drive is as follows: /dev/sda2:Good /dev/sdb2 (drive has physical problem so no partition data) bad, /dev/sdc2:good /dev/sdd2:good. Every time I reboot the mdadm system seems to keep trying to use /dev/sdb which has physical failure (although spins and is detected). /dev/sdd is the new drive I created. I added /dev/sdd to the raid and it rebuilds the raid but this action isn't memorized upon reboot so it keeps listing /dev/sda and /dev/sdc but doesn't use the perfectly good /dev/sdd until I re-add manually. I've tried removing the dead drive with the mdadm tool, but as it cannot see /dev/sdb paritions it will not fail or remove it (says partition doesn't exist). the /etc/mdadm.conf was automatically made on the original OS install which only lists: DEVICE partitions MAILADDR root ARRAY /dev/md2 super-minor=2 ARRAY /dev/md0 super-minor=0 ARRAY /dev/md1 super-minor=1 Basically just the raids to use on boot. I need to remove this semi-dead drive (/dev/sdb) but I'd prefer to know why this is happening before I do. any ideas or suggestions. I supposed I could attempt to clone/replace /dev/sdb (the partitions on drive show up, then disappear shortly after) but given the partition "chester cat" behaviour this seems risky to me and as I have a working "spare" it seems unnecessary. Thanks in advance for your insight.

  Read the article

• Limited user requires admin rights for plug and play printer?

  - by Kalamane

  I have a small fleet of laptops that aren't part of a domain running Windows XP Pro SP3 as limited users. They are used for printing different shipping documents. I have a script that runs when they start up that uses devcon and prntmngr to detect and install/configure the currently connected usb printers. This lets us deploy the laptops to any printing station with a USB printer and have the printer 'just work' for the end user employee. I've taken the original clone image and have added functionality to it. Since then I've discovered a bit of an issue with using HP LaserJet P1606dn printers. They have started asking for admin rights on setup. This is with and without the script running. Previously they would automatically install because I had installed WHQL plug and play drivers for them. I thought it might have to do with the HP Smart Install Utility but it happens when that is disabled. I don't have a good point to roll back to before this started happening because this was an issue on the image I took initially to start this upgrade. What could be causing this?

  Read the article

• Master does not appear to be a git repository error

  - by EmmyS

  I've inherited a position and instructions for creating a new git repository. Unfortunately I've run into problems and no one here knows what to do. Hoping someone can help me out. Here are the instructions I was left: Create a new repository: For these steps you need to be in the gitosis-admin repository, if you don't have it, in a suitable parent folder do: git clone [email protected]:gitosis-admin.git Edit gitosis.conf file - in gitosis-admin root, under [group base-repo] section, add the name of the new repo to the end of the "writable =" section. Commit change and push back to gitosis-admin master. For the next commands, my_new_project represents the name of your project mkdir my_new_project cd my_new_project git init Copy in any files you want to use to start the repo git commit -a -m "Initializing new repository" git remote add origin [email protected]:my_new_project.git git push master git push master:qa So I did 1 and 2, with no problem. It created a local folder on my machine called gitosis-admin. I edited the gitosis.conf file as indicated. But when I try to do step 3 (which I assume is git push gitosis-admin master) bash tells me that fatal: 'master' does not appear to be a git repository fatal: The remote end hung up unexpectedly What am I doing wrong?

  Read the article

• Last step in HDD Recovery (fixing windows)

  - by Atom Computing

  My dad’s hard drive corrupted which was a result of many bad sectors. Anyway, I made a clone of the drive and have now repaired it totally (recreating the MBR and MFT) and doing a series of ChkDsk's on it. I can now see all the files and folder on it and it is all intact. I currently have it as a slave in my computer (where I was doing all the repairs). When putting it back into the computer, it comes up with "A disk read error occurred: Press Ctrl + Alt + Del to Restart". I don’t know why this is happening but think it might have something to do with file permissions. I have tried a start-up recovery on the Vista boot CD and it found no problems. When trying to apply file permissions (and creating file perms for the SYSTEM group (as it didn’t have any for SYSTEM group)) it couldn't apply them for some of the System32 folder files. I have tried applying them as admin and with as powerful privileges I can get. All to no avail. When it is in my PC I can boot it up (I added it into my bootloader) and it boots up fine except when it logs in it comes up with the error - "Rundll32.exe - Windows cannot access the specified device, path or file. You may not have the appropriate permissions to access the item" This message keeps coming back and nothing loads at all. Any help would be greatly received as I have got so far with the data recovery and want to avoid a reformat at all costs due to the vast number of programs installed and I don’t have much time on my hands! Thanks

  Read the article

• Is there any functional-like unix shell?

  - by Caruccio

  I'm (really) newbie to functional programming (in fact only had contact with it using python) but seems to be a good approach for some list-intensive tasks in a shell environment. I'd love to do something like this: $ [ git clone $host/$repo for repo in repo1 repo2 repo3 ] Is there any Unix shell with these kind of feature? Or maybe some feature to allow easy shell access (commands, env/vars, readline, etc...) from within python (the idea is to use python's interactive interpreter as a replacement to bash). EDIT: Maybe a comparative example would clarify. Let's say I have a list composed of dir/file: $ FILES=( build/project.rpm build/project.src.rpm ) And I want to do a really simple task: copy all files to dist/ AND install it in the system (it's part of a build process): Using bash: $ cp ${files[*]} dist/ $ cd dist && rpm -Uvh $(for f in ${files[*]}; do basename $f; done)) Using a "pythonic shell" approach (caution: this is imaginary code): $ cp [ os.path.join('dist', os.path.basename(file)) for file in FILES ] 'dist' Can you see the difference ? THAT is what i'm talking about. How can not exits a shell with these kind of stuff build-in yet? It's a real pain to handle lists in shell, even its being a so common task: list of files, list of PIDs, list of everything. And a really, really, important point: using syntax/tools/features everybody already knows: sh and python. IPython seams to be on a good direction, but it's bloated: if var name starts with '$', it does this, if '$$' it does that. It's syntax is not "natural", so many rules and "workarounds" ([ ln.upper() for ln in !ls ] -- syntax error)

  Read the article

< Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >