Search Results

Search found 2602 results on 105 pages for 'dell poweredge'.

Page 62/105 | < Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >

  • Screen Corruption in half the screen only

    - by Guy DAmico
    About 50% of the my NATTY desktop screen is corrupted. Once that happens I can re-boot as many times as I want but the problem continues. If I logout and then into WINDOWS for a day I may be successful and boot UBUNTU with a good screen. The desktop is formatted correctly, there's no pixelation, rather there is a fine grained white crosshatch pattern covering the entire screen. If I open any application the screen corruption worsens eventually to the point I can no longer make out anything. I ran ram memory test w/o any errors. I have no display issues when running WINDOWS 7. Any ideas. My computer is a Dual Boot stock DELL 5150 w/3gig of ram an on board video.

    Read the article

  • Wireless card disappeards when restart ubuntu

    - by Kristian Jones
    I used 'additional drivers' to install 'Broadcom STA wireless driver' and it returns an error. WIthin jockey.log it says the following numerous times. 2011-02-14 21:24:06,945 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted After it returns the error the network card will work temporarily until I restart the laptop. When I restart I got to go through the procedure again of trying to activate the driver, returns an error however it works temporarily. The network card is as follows on a Dell Inspiron 1545: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] Rev 01 I have been trying to solve this myself for many hours. Any help is appreciated/

    Read the article

  • Ubuntu 14.04 ATI/Intel Hybrid Graphics DPM

    - by anchit123
    I have a Dell Inspiron 3521 with hybrid ATI/Intel graphics. (AMD Radeon 7670M / Intel HD 4000) using Ubuntu 14.04 with open source drivers for graphics. (xserver-xorg-video-ati) I read that Ubuntu 14.04 with the linux kernel version 3.13 supports auto switching between graphics and dynamic power management. Is it correct? Anyway, if it is true, I dont think that it is working in my system , because fan runs constantly and battery backup is less than 2 hours. lspci | grep -i vga 00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) 01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Thames [Radeon HD 7500M/7600M Series] (rev ff) What should I do? Is there any hope that this gets fixed in future kernels?

    Read the article

  • Best Practice for Images in Facebook Pages

    - by BFTrick
    Hello I am looking for best practices when it comes to uploading images on facebook fan pages. I notice on Dell, US Cellular, and the Gap that they load all of their images on one of their web servers. Are there any alternatives? I was hoping for something like being able to upload photos and then hide the gallery. But I couldn't find anything like that. The reason that I ask is that I have access to someone's facebook fan page but not to their webserver so it would be extra work to email someone who does have access the photos and have them upload them to their web server.

    Read the article

  • Windows XP with Ubuntu 14.04 on 2 separate hard drives

    - by maplenet2
    I am new to Ubuntu. I have Windows XP Professional 32-bit on one 300GB IDE hard drive and Ubuntu 14.04 running on another 61GB IDE hard drive, and I cannot get my Windows XP to boot with Grub! When I select Windows XP from the boot menu, Grub just restarts my computer. The computer I have with those two hard drives is a Dell Optiplex GX240, so the hardware is old, and its BIOS won't let me change the boot priority on the two IDE hard drives. What can I do now? Is there a step I missed when installing Ubuntu? Can I edit Grub to boot Windows XP without messing with the BIOS? Do I have to downgrade to an older release of Ubuntu to make it work? I am willing to reinstall Ubuntu, if that's what it takes.

    Read the article

  • Cheese with vaapi

    - by MetaDark
    Hi, I am using a Dell Inspiron Mini 10 with GMA500 video drivers. GMA500 fixes resolution issues and enables video acceleration. The only problem with the GMA500 drivers I am having is that I can not find a fix for the webcam program called cheese, and I can't find a way to enable the vaapi (Video Acceleration API) backend. Videos don't work with the GMA500 (without vaapi) and I cannot properly use cheese. If anyone can help me out with this I will be grateful because Google isn't helping me much with this problem.

    Read the article

  • Nautilus is really slow

    - by david
    Nautilus used to be lightning fast.Now it's dead slow. I have tried upgrading the video card but that does not seem to be the problem. Also I found that there was a problem with the Dropbox uninstall, finally I replace it with pcmanfm which appears to be much faster but the down side is that I no longer have the gwibber social client and a lot of stuff don't work like they use to. Also I completely removed nautilus and couldn't even login to ubuntu to install again nautilus.How can I remove or repair nautilus, and use pcmanfm instead? I have a dell inspiron 1440 3gb ram / disk 300gb / Additionally, why does nautilus run fast when I run it as root? There are no USB devices attached to my computer. Thanks in advance

    Read the article

  • Unmet Dependencies when I try to install wine or skype

    - by Andres
    I have a dell inspiron 64 bit and I'm running both windows 7 and Ubuntu in dual boot I am having trouble installing skype and wine. When I try to install skype etc I get the following error: sudo apt-get install ia32-libs Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are Blockquote using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-multiarch but it is not installable E: Unable to correct problems, you have held broken packages

    Read the article

  • How can I enable Unity 3d after installing Bumblebee? GLX Problems

    - by ashley
    I'm new to Ubuntu, I'm running 12.04 64 Bit on a Dell XPS L207x with a Nvidia GT555M card. From what I could understand online I needed to install Bumblebee to get the most out of the Optimus system and better battery life. I can test the Bumblebee is working by running optirun glxgears for example. If I run just glxgears then I get the following error Error: couldn't get an RGB, Double-buffered visual. I'm also unable to run Unity 3d, which I would very much like. I'd greatly appreciate any and all help, please be gentle.

    Read the article

  • Crashes while playing Mp3 songs

    - by sid
    I have Downloaded and Installed Ubuntu last month while downloading codecs for playing Music and Video Formats my Laptop (Dell XPS) crashed. later i again started the system now the problems i face are 1) After Signing in as User/Admin the wallpaper loads while all other windows disappear no UI (task bar and dock) is displayed even after say 30 min. 2) I uninstalled and reinstalled Ubnutu hence there were no problems but when i play Music files the Laptop crashes and the same sequence as above follows this has happened for last 6 times. 3) Whenever the UI disaapears after logging in the Hard Disk starts to heat up and there is considerable increase in power usage of the system. where in the power drain is notable. Please suggest any changes or rectify the issue. Regards Sid

    Read the article

  • Removal of libsound2 file causes graphics loss

    - by Sajid Ahmad
    I was trying to install skype on ubuntu 12.10 desktop. but it was giving some error related to libsound2:i386 file. to overcome this problem i removed file libsound2 thinking that will install it later. but it removes all the graphics from my system. after removal of the file system started to give error that system is running in low graphics mode. I tried to install libsound2 file again but couldn't. After it i have upgraded the release of my ubuntu version using command do-release-upgrade think that it will install the missing file. But still there are no graphics on the system. I am using Dell Inspiron 15 . Please help me to tell that how can i get the graphics of system back.

    Read the article

  • How to list missing partitions?

    - by celebrimbor
    I have installed Ubuntu on one of my partition and Crunchbang on the other partition. As I wanted to make some continuous space, I moved Crunchbang partition and then checked fdisk output which looks like this Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc7996dfa Device Boot Start End Blocks Id System /dev/sda1 * 63 80324 40131 de Dell Utility /dev/sda4 81918 625139711 312528897 f W95 Ext'd (LBA) /dev/sda5 81920 211816447 105867264 83 Linux /dev/sda6 299100160 341043199 20971520 83 Linux /dev/sda7 341045248 625139711 142047232 7 HPFS/NTFS/exFAT I cannot see sda2 and sda3 partition. How to find them?

    Read the article

  • Can't mount cds after failed Brasero burn

    - by Allan
    Brasero failed to burn a disk recently, and now I can't access CD-ROMS. Even CD-Rs are not not showing. Using Ubuntu 11.10 on a Dell D510 Lattitude laptop. allan@allan-Latitude-D510:~$ cdrecord -checkdrive Device was not specified. Trying to find an appropriate drive... Detected CD-R drive: /dev/cdrw Using /dev/cdrom of unknown capabilities Device type : Removable CD-ROM Version : 5 Response Format: 2 Capabilities : Vendor_info : 'TSSTcorp' Identification : 'DVD+-RW TS-L532B' Revision : 'DE04' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R96R My CD drive is now useless, and any help on getting it to read/burn would be appreciated.

    Read the article

  • Sound Problem due to wrong driver installation

    - by Starx
    First of all, the audio used to play from the speaker but whenever I connected a headphone or speaker in the I, the sound didn't came. So I installed a realtek sound driver to fix this (actually I didn't find any relevant driver for my sound card so I installed it hoping it would show some light) When I rebooted the system, my sound is completely gone and now ubuntu does not detect any sound devices in my system. I clearly installed wrong driver, now I need to remove and go to previous stage and find a correct driver. My laptop is: Dell Studio 1747, uses a speaker Creative Labs Sound X-Fi MB Sound Blaster and the chipset is INTEL PM55. How can I fix this?

    Read the article

  • Why can't I use Unity 3D on a ATI Mobility Radeon HD 4200 Series with FGLRX drivers?

    - by user88257
    With a brand new install of 12.04 on my Dell Inspiron M5030, Unity 3D appears to load everything but the icons in the top left, and I am unable to click on anything. Unity 2D seems to works fine however. I have done nothing except install Synaptic Package manager and follow this guide to install FGLRX Drivers under Settings ? Additional Drivers, the driver shows as installed and functioning. Also after running: /usr/lib/nux/unity_support_test -p, I get this: OpenGL vendor string: ATI Technologies Inc. OpenGL renderer string: ATI Mobility Radeon HD 4200 Series OpenGL version string: 3.3.11653 Compatibility Profile Context Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: yes I am unsure as to what the problem is. I have tried the non-proprietary drivers, I could not get them to work either, but I would be willing to try again.

    Read the article

  • Wifi not working for Ubuntu 14.04

    - by user286975
    I have installed the Ubuntu 14.04 on Dell Vostro 2520 laptop. Wifi is not working after installation. Tried several methods to install but nothing happens. Vostro-2520:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no Vostro-2520:~$ iwconfig usb0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. The hardware is Broadcom 802.11 bcm43142. Please help to solve this issue.

    Read the article

  • Upgrade from 11.10 to 12:04 failed

    - by Sandeep Adi
    I upgraded from Ubuntu 11.10 to 12.04 using the update manager. At the end of the upgrade the console said the upgrade had failed and it forced me to restart. After a restart I am not able to do anything other than logging in. I just see a blue screen with the ubuntu one icon, I can open applications, but nothing beyond that. I opened the terminal but after that the keyboard is not being recognized. Basically the laptop is now rendered useless. Any pointers on how to recover? This is on a Dell Inspiron 1501 laptop with a 64 bit AMD Sempron Processor. Any help would be appreciated. Thanks, Sandeep

    Read the article

  • Sound distortion in Ubuntu 14.04

    - by Aditya Shah
    I recently installed Ubuntu 14.04 on my Dell XPS 15 (L502X). Previously I had Ubuntu 12.04 installed on the laptop along with Windows 8.1 dual boot. The sound worked perfectly fine in Ubuntu 12.04 and is working fine in Windows 8.1. Of late, I have been experiencing sound distortion coming from the subwoofer at moderately high volume levels. At the same level I am unable to reproduce the same effect in Windows 8.1. Also, I did a clean install of Ubuntu 14.04 over 12.04. Can anyone please confirm this and help me with this? Thanks

    Read the article

  • stuck with 640x480 resolution using bumblebee on 10.04

    - by pholz
    I just installed bumblebee on a Dell XPS L502X. It basically works: optirun glxspheres does exactly what it should. However, X is running with a resolution of 640x480. I can try to change settings with optirun nvidia-settings -c :8 (as suggested on the bumblebee wiki), but in the relevant section it only lists resolutions up to 640x480. In the /etc/bumblebee/xorg.conf.* files, there are no Monitor or Screen sections. Adding them doesn't change anything. How can I change the resolution?

    Read the article

  • nvidia GT 525m no screen found

    - by Pavan
    I'm a Dell XPS user with nvidia GT 525M with Optimus. When I installed nvidia I was greeted with blank screen. And the error in nvidia log was "Fatal error : No screen found". So after searching for the solutions I figured that I have to insert "BusID" in xorg.conf file. After rebooting I was again greeted with blank screen with error "Fatal error : screen already occupied". I don't what exactly the problem is. Do I need to blacklist Intel inbuilt graphics to nvidia in my machine or anything else needs to be done? Please guide me.

    Read the article

  • is gnome 3 is slow or my machine?

    - by user103054
    I have Dell XPS 15 i7 - 2360 with nvidia 525M (1GB) with optimus running Ubuntu 12.10 64 bit and have bumblebee installed for optimus. Recently I installed Gnome Shell to give it a try and found it sort of lagging under few scenarios though rest all is butter smooth. When I click on Date gnome 3 it appears as if a second has elapsed before the window is drawn. But others panel items like network or volume looks fine. In gnome 3 when I'm on dash with (window preview) if I remove any of the windows before the remaining windows reshuffle it takes about 2 seconds (noticeable clearly). Everything else is fine in both unity and Gnome Shell. What is causing this slowness? Is Gnome Shell is really slower?

    Read the article

  • Broadcom wireless card disappeards on restart

    - by Kristian Jones
    I used 'additional drivers' to install 'Broadcom STA wireless driver' and it returns an error. WIthin jockey.log it says the following numerous times. 2011-02-14 21:24:06,945 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted After it returns the error the network card will work temporarily until I restart the laptop. When I restart I got to go through the procedure again of trying to activate the driver, returns an error however it works temporarily. The network card is as follows on a Dell Inspiron 1545: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] Rev 01 I have been trying to solve this myself for many hours. Any help is appreciated/

    Read the article

  • Why does waking from hibernate take nearly ten minutes on 11.10?

    - by Shane O'Connor
    Im running 11.10 64bit on a Dell XPS 15 L502x laptop. It uses an i5 proc and has 16Gb ram. Whenever I close the lid on the laptop I have it set to hibernate as I want to continue whatever I was previously running. Generally that is simple text editing, so my mem usage would normally be only a Gb or 2. When I open the lid and it resumes from Hibernation, it takes up to ten minutes to do so. Extremely frustrating. Is there anything I can do to make hibernate function properly. On windows it used to wake from Hibernation in less than 30 seconds. Its really frustrating and souring my experience with Ubuntu. Any help would be gratefully appreciated! Thanks guys/gals! S

    Read the article

  • It's noisy in ubuntu,why?

    - by Jinx
    I just installed an ubuntu on my pc(Dell Inspiration I560SR-358, with CPU E5700 3GHz, 4G memory, and NVIDIA GeForce G310). The pc becomes noisy before that it's quiet with a windows 7 on it. How come? How to set it to be quiet again in unbuntu 10.04. One of the two cpu usage is always 100%. I think that is the reason. //re-edit Everything gets ok after I restart the computer.But the fan is still running which makes it noisy, if i switch to windows 7, it becomes quiet again.

    Read the article

  • How to setup ATI Mobility Radeon HD 4650?

    - by Thi An
    I'm currently using Ubuntu 12.04 64bit. After installing ATI/AMD proprietary FGLRX graphics drivers via Additional Drivers, I checked the status of my VGA card using lspci -v. Here's the output: 02:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI M96 [Mobility Radeon HD 4650] (prog-if 00 [VGA controller]) Subsystem: Dell Device 0456 Flags: bus master, fast devsel, latency 0, IRQ 46 Memory at d0000000 (32-bit, prefetchable) [size=256M] I/O ports at 2000 [size=256] Memory at cfef0000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at cfe00000 [disabled] [size=128K] Capabilities: Kernel driver in use: fglrx_pci Kernel modules: fglrx, radeon As mentioned in the title, my VGA card is 1GB and yet my computer only recognizes 256MB. My question is: "How to make my computer fully recognize the capacity of my ATI Mobility Radeon HD 4650 (1GB)?"

    Read the article

< Previous Page | 58 59 60 61 62 63 64 65 66 67 68 69  | Next Page >