Search Results

Search found 7843 results on 314 pages for 'power over ethernet'.

Page 63/314 | < Previous Page | 59 60 61 62 63 64 65 66 67 68 69 70  | Next Page >

  • How do ISPs/Colocation Facilities limit bandwidth for Ethernet Drops?

    - by Kyle Brandt
    I have switch providers and have run into some problems with bandwidth limitations. I have more bandwidth then before, but there are performance issues. The router is connected to a 100mBit port, but they limit it to arbitrary settings (in software I imagine). It seems when I go above the limit, the provider starts to drop packets beyond the limit (This is what they said they do as well). Is it possible the previous provider did something like queuing packets above the this limit before dropping them? Is anyone aware of not only what can be done, but what is typical? Also, is there anything I can do on my Cisco router to help this situation? It would seem I am pretty helpless if the packets are dropped before they reach my interface (The traffic that is high is inbound to my network).

    Read the article

  • How can I join two simple home networks together using an ethernet cable?

    - by Ilia Jerebtsov
    I want to join two different home networks together like so: PC A1 PC A2 PC B1 PC B2 \ / \ / Gateway A <----- ethr. cable -----> Gateway B | | ADSL modem A ADSL modem B Both networks are of the basic residential type with identical configuration, with all PCs running Vista/7. The point is to temporarily join two apartments in a building for gaming and file sharing, and the holy grail would be: PCs on network A can access PCs on network B and vice-versa (file shares and gaming). Each network uses its own internet connection. Data between networks shouldn't take a trip through the internet (broadband upload speeds are severely capped) A network's internet access should continue working if the joining cable is disconnected with minimal configuration changes. How closely can this be achieved?

    Read the article

  • Trying to prevent Windows from hibernating/sleeping automatically

    - by user328821
    My Dell XPS 8700 (Win 7) suddenly began putting itself to sleep at 6pm daily, even if I'm typing. I don't know what caused this to occur, except possibly a windows update that took place in the middle of the night. I initially went into settings for power and saw 2 plans set up, one from Dell and the other window's Power saver plan. I set both to never for sleep and hibernate yet it still occurred. I have current drivers and a fairly new UPS that has software to set to shutdown only after power loss. Dell is of little help, can anyone point me in the right direction? I did do the powerdfg -energy program and came up with this: Power Efficiency Diagnostics Report Scan Time 2014-05-08T19:21:48Z Scan Duration 60 seconds System Manufacturer Dell Inc. System Product Name XPS 8700 BIOS Date 08/23/2013 BIOS Version A04 OS Build 7601 Platform Role PlatformRoleDesktop Plugged In true Process Count 115 Thread Count 1631 Report GUID {097caf99-039b-44c3-b154-d797bfbfdfcc} Analysis Results Errors Power Policy:Sleep timeout is disabled (Plugged In) The computer is not configured to automatically sleep after a period of inactivity. System Availability Requests:System Required Request The device or driver has made a request to prevent the system from automatically entering sleep. Requesting Driver Instance HDAUDIO\FUNC_01&VEN_10EC&DEV_0899&SUBSYS_102805B7&REV_1000\4&220b1bbc&0&0001 Requesting Driver Device Realtek High Definition Audio CPU Utilization:Processor utilization is high The average processor utilization during the trace was high. The system will consume less power when the average processor utilization is very low. Review processor utilization for individual processes to determine which applications and services contribute the most to total processor utilization. Average Utilization (%) 9.48 Warnings Platform Timer Resolution:Platform Timer Resolution The default platform timer resolution is 15.6ms (15625000ns) and should be used whenever the system is idle. If the timer resolution is increased, processor power management technologies may not be effective. The timer resolution may be increased due to multimedia playback or graphical animations. Current Timer Resolution (100ns units) 10000 Maximum Timer Period (100ns units) 156001 Platform Timer Resolution:Outstanding Kernel Timer Request A kernel component or device driver has requested a timer resolution smaller than the platform maximum timer resolution. Requested Period 10000 Request Count 2 Platform Timer Resolution:Outstanding Timer Request A program or service has requested a timer resolution smaller than the platform maximum timer resolution. Requested Period 10000 Requesting Process ID 8672 Requesting Process Path \Device\HarddiskVolume3\Program Files (x86)\Mozilla Firefox\firefox.exe Platform Timer Resolution:Outstanding Timer Request A program or service has requested a timer resolution smaller than the platform maximum timer resolution. Requested Period 100000 Requesting Process ID 1212 Requesting Process Path \Device\HarddiskVolume3\Windows\System32\svchost.exe Power Policy:802.11 Radio Power Policy is Maximum Performance (Plugged In) The current power policy for 802.11-compatible wireless network adapters is not configured to use low-power modes. CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace. Process Name audiodg.exe PID 1304 Average Utilization (%) 4.73 Module Average Module Utilization (%) \Device\HarddiskVolume3\Windows\System32\msvcrt.dll 1.88 \Device\HarddiskVolume3\Windows\System32\MaxxAudioAPO5064.dll 1.77 \Device\HarddiskVolume3\Windows\System32\AudioEng.dll 0.80 CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace. Process Name thunderbird.exe PID 6036 Average Utilization (%) 0.35 Module Average Module Utilization (%) \Device\HarddiskVolume3\Program Files (x86)\Mozilla Thunderbird\xul.dll 0.16 \Device\HarddiskVolume3\Program Files (x86)\Mozilla Thunderbird\mozjs.dll 0.05 \SystemRoot\System32\win32k.sys 0.03 CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace. Process Name dwm.exe PID 1340 Average Utilization (%) 0.25 Module Average Module Utilization (%) \Device\HarddiskVolume3\Windows\System32\dwmcore.dll 0.08 \Device\HarddiskVolume3\Windows\System32\nvwgf2umx.dll 0.05 \SystemRoot\system32\ntoskrnl.exe 0.03 CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace.

    Read the article

  • A can ping B, B can ping C but A cant ping C. How do i connect A to C (ethernet)?

    - by user16654
    I have a computer at home with ip 192.168.221.xxx I have another computer at work that I can ping and it has 2 ip addresses: 192.168.1.xxx and 192.168.0.xxx. Those last 2 addresses have the same gateway ie 192.168.1.1 . The computer at work is connected to a hub. That hub also has an embedded device connected to it with address 192.168.0.xxx Now from my home computer I cannot ping this embedded device. How would I connect to it without changing the subnetwork it connects to? I can ping the embedded device from my work computer and I can ping the work computer from my home computer. So I am trying to connect to the embedded device from my home computer through my work computer. Port forwarding? how would I establish that on Ubuntu?

    Read the article

  • How do I create a script that checks if a computer is connected via wireless or ethernet?

    - by user4941
    I am using log-me-in Central to look after a few dozen computers. These computers are used both for home use and work use. When the computers are used for work, they should not be connected via wireless. In the best case, I'd like to be able to use LogMeIn to prevents users on shift from connecting wirelessly. Still acceptable would be to have the computer email me if it connects wirelessly. If I knew how to set up a script that checks to see if the computer connected wirelessly and I could send an email, then I would be set.

    Read the article

  • Can I make Windows behave like an ethernet hub?

    - by dromedary
    I have two machines A and C mutually connected to NICs on a third machine, B, as follows: A-B-C B is a Windows 7 machine configured with a bridge containing the A-B and B-C NICs, so that A and C can communicate. So far, so good. I need frames from A destined for B to also arrive at C. Essentially, I would like Windows to behave like a hub rather than a switch. Is there any way to do this? If you have any ideas at all, no matter how hacky or roundabout, I would love to hear from you! I have been tearing my hair out over this and by now I am willing to try anything. My only limitations are that I can't touch A or change to a different operating system on B.

    Read the article

  • Electronic circuit simulator four-way flood-filling issues

    - by AJ Weeks
    I've made an electronic circuit board simulator which has simply 3 types of tiles: wires, power sources, and inverters. Wires connect to anything they touch, other than the sides of inverters; inverters have one input side and one output side; and finally power tiles connect in a similar manner as wires. In the case of an infinite loop, caused by the output of the inverter feeding into its input, I want inverters to oscillate (quickly turn on/off). I've attempted to implement a FloodFill algorithm to spread the power throughout the grid, but seem to have gotten something wrong, as only the tiles above the power source get powered (as seen below) I've attempted to debug the program, but have had no luck thus far. My code concerning the updating of power can be seen here.

    Read the article

  • Mouse Problem on Ubuntu 12.10

    - by KashmirHackers
    I had a strange mouse problem on Ubuntu 12.10(64-Bit), the problem is that when I turnoff power supply/power goes off, the red laser light of my mouse also goes off and my mouse stops working but it works fine when A/C power supply is on. First I thought my mouse or my laptop's USB ports had problem but since I am using Dual Boot with windows 7, I checked my mouse on windows 7 and it works fine, even I turn off power supply. Today,I thought that I should give a try to Linux Mint 14-RC (which is based on same Ubuntu 12.10) and after installing linux mint when I plugged in my mouse it worked fine even though power is off. Don't know what is really going on, and I am afraid if I reinstall my Ubuntu 12.10 the problem will remain.

    Read the article

  • ?Oracle Database 12c????ASM Scrubbing Disk Groups

    - by Liu Maclean(???)
    ?12.1?Oracle ASM??????????????????? ??Scrubbing Disk Groups, Disk Scrubbing???????????,?????Normal ??High Redundancy?disk group?????? Scrubbing ?????????????????Disk Scrubbing???disk group rebalancing???????I/O?????Disk Scrubbing??????I/O????? ?????????Scrubbing????,?????,????????????,?????ALTER DISKGROUP?????????: SQL> ALTER DISKGROUP data SCRUB POWER LOW; SQL> ALTER DISKGROUP data SCRUB FILE '+DATA/ORCL/ASKMACLEAN/example.266.806582193' REPAIR POWER HIGH FORCE; SQL> ALTER DISKGROUP data SCRUB DISK DATA_0005 REPAIR POWER HIGH FORCE; ?????SCRUB ?: ??REPAIR??????????,?????REPAIR,?SCRUB???????????????? ??POWER?????AUTO LOW HIGH ??MAX? ?POWER???,???AUTO????? ??WAIT ???????scrubbing ?????????WAIT???,?scrubbing??????scrubbing queue ??,??????? ?FORCE?????,?????I/O????????????????scrubbing ,????????

    Read the article

  • Delphi - Proper way to page though data.

    - by Brad
    I have a string list (TStrings) that has a couple thousand items in it. I need to process them in groups of 100. I basically want to know what the best way to do the loop is in Delphi. I'm hitting a brick wall when I'm trying to figure it out. Thanks unit Unit2; interface uses Windows, Messages, SysUtils, Variants, Classes, Graphics, Controls, Forms, Dialogs, StdCtrls; type TForm2 = class(TForm) Memo1: TMemo; Memo2: TMemo; Button1: TButton; procedure Button1Click(Sender: TObject); private { Private declarations } public { Public declarations } end; var Form2: TForm2; implementation Uses math; {$R *.dfm} procedure TForm2.Button1Click(Sender: TObject); var I:Integer; pages:Integer; str:string; begin pages:= ceil(memo1.Lines.Count/100) ; memo2.Lines.add('Total Pages: '+inttostr(pages)); memo2.Lines.add('Total Items: '+inttostr(memo1.Lines.Count)); // Should just do in batches of 100 VS entire list for I := 0 to memo1.lines.Count - 1 do begin if str '' then str:= str+#10+ memo1.Lines.Strings[i] else str:= memo1.Lines.Strings[i]; end; //I need to stop here every 100 items, then process the items. memo2.Lines.Add(str); end; end. Example form object Form2: TForm2 Left = 0 Top = 0 Caption = 'Form2' ClientHeight = 245 ClientWidth = 527 Color = clBtnFace Font.Charset = DEFAULT_CHARSET Font.Color = clWindowText Font.Height = -11 Font.Name = 'Tahoma' Font.Style = [] OldCreateOrder = False PixelsPerInch = 96 TextHeight = 13 object Memo1: TMemo Left = 16 Top = 8 Width = 209 Height = 175 Lines.Strings = ( '4xlt columbia thunder storm jacket' '5 things about thunder storms' 'a thunder storm with a lot of thunder ' 'and lighting sccreensaver' 'a thunder storm with a lot of thunder ' 'and lighting screensaver with no nag ' 'screens' 'all about thunder storms' 'all about thunderstorms for kids' 'amazing tornado videos and ' 'thunderstorm videos' 'are thunder storms louder in ohio?' 'bad thunder storms' 'bathing in thunder storm' 'best thunderstorm pictures' 'cartoon thunder storms' 'celtic thunder storm' 'central valley thunder storm' 'chicago thunderstorm pictures' 'cool thunderstorm pictures' 'current thunderstorm warnings' 'does thunder storms in december mean ' 'snow will be coming' 'facts about thunderstorms for kids' 'facts on thunderstorms for kids' 'fedex thunderstorm video' 'florida thunderstorms facts' 'free relaxing thunderstorm music' 'free soothing thunderstorm sounds ' 'online' 'free thunderstorm mp3' 'free thunderstorm mp3 download' 'free thunderstorm mp3 downloads' 'free thunderstorm mp3s' 'free thunderstorm music' 'free thunderstorm pictures' 'free thunderstorm sound effects' 'free thunderstorm sounds' 'free thunderstorm sounds cd' 'free thunderstorm sounds mp3' 'free thunderstorm sounds online' 'free thunderstorm soundscape' 'free thunderstorm video' 'free thunderstorm video download' 'free thunderstorm videos' 'god of storm and thunder' 'horses storm thunder rain' 'how do thunder storms form' 'how far away is a thunder storm' 'how long do thunder storms last' 'ice cube in a thunder storm' 'indoor thunderstorm safety tips' 'information about thunderstorms for kids' 'interesting thunderstorm facts' 'is it dangerous to shower during thunder ' 'storm' 'is there frequently thunder during snow ' 'storms' 'isolated thunderstorms' 'it'#39's just a thunder storm baby there is ' 'nothing you should fear lyrics' 'lightning & thunder storm safety' 'lightning and thunderstorm facts' 'lightning and thunderstorms facts' 'lightning and thunderstorms for kids' 'listen to thunderstorm sounds online' 'mississauga thunder storm' 'nature sounds free mp3 thunder storm' 'only about thunderstorms facts' 'original storm deep thunderstick' 'phone use during thunder storms' 'pictures of thunderstorms' 'pocono thunder storm' 'posters of thunder storms' 'power rangers ninja storm' 'power rangers thunder storm' 'power rangers thunder storm cast' 'power rangers thunder storm games' 'power rangers thunder storm morphers' 'power rangers thunder storm part 1' 'power rangers thunder storm part 2' 'power rangers thunderstorm' 'power rangers thunderstorm cannon' 'power rangers thunderstorm deluxe ' 'megazord' 'power rangers thunderstorm games' 'power rangers thunderstorm megazord' 'power rangers thunderstorm part 2' 'power rangers thunderstorm pictures' 'power rnager ninja storm thunder staff' 'powerful thunder and lightning storms' 'precambrian thunder storms' 'rain thunderstorm mp3' 'rain thunderstorm pictures' 'relaxing thunderstorm music' 'reminds me of ohio river thunder lighten ' 'storms' 'sacramento thunder storm' 'safety tips for when your caught in a ' 'thunder storm' 'scattered thunderstorms' 'schemer puts his head in the thunder ' 'storm' 'sedative thunder storm' 'server thunder storms' 'severe supercell thunderstorm pictures' 'severe thunder storm pictures' 'severe thunder storms' 'severe thunderstorm facts' 'severe thunderstorm pictures' 'severe thunderstorm pictures hail' 'severe thunderstorm pictures in alberta' 'severe thunderstorm pictures tornado' 'severe thunderstorm safety' 'severe thunderstorm safety tips' 'severe thunderstorm videos' 'severe thunderstorm warning' 'severe thunderstorm warning los ' 'angeles' 'severe thunderstorm warning signs' 'severe thunderstorm warnings' 'severe thunderstorms' 'severe thunderstorms facts' 'shakespeare use thunder storm for ' 'cosmic disorder julius caesar' 'soothing thunderstorm sounds online' 'sound effects of severe thunder storm' 'sound of rain storm finger snapping ' 'thunder chorus' 'split thunder storm' 'storm 3d thunder power' 'storm dark thunder' 'storm dark thunder bowling ball' 'storm dark thunder bowling ball sale' 'storm dark thunder for sale' 'storm dark thunder pearl' 'storm dark thunder pearl bowling ball' 'storm dark thunder review' 'storm dark thunder shirt' 'storm dark thunderball' 'storm deep thunder' 'storm deep thunder 11' 'storm deep thunder 15' 'storm deep thunder 15 lure' 'storm deep thunder 2' 'storm deep thunder lures' 'storm deep thunderstick' 'storm deep thunderstick crankbaits' 'storm deep thunderstick dts09' 'storm deep thunderstick jr' 'storm deep thunderstick lures' 'storm deep thundersticks' 'storm rolling thunder 3 ball roller' 'storm rolling thunder bowling bag' 'storm rolling thunder three ball bowling ' 'bag' 'storm shallow thunder' 'storm shallow thunder 15' 'storm thunder claw' 'storm thunder craw' 'storm watches thunder' 'storms with constant lightning and ' 'thunder non-stop' 'supercell thunder storms' 'supercell thunderstorm pictures' 'supercell thunderstorms' 'swimming pools thunder storms' 'tampa + lightning strikes + thunder ' 'storms' 'texas thunderstorm pictures' 'texas thunderstorm warnings' 'thunder and lightning storm' 'thunder and lighting storms' 'thunder and lightning storms' 'thunder bay snow storm video' 'thunder storm' 'thunder storm and windmill' 'thunder storm cd' 'thunder storm cloud' 'thunder storm clouds' 'thunder storm dog peppermint oil' 'thunder storm in winter' 'thunder storm in winter and weather ' 'prediction' 'thunder storm lx-3 & road blaster psx ' 'download' 'thunder storm occurances' 'thunder storm photos' 'thunder storm poems' 'thunder storm safety' 'thunder storm sign' 'thunder storm sounds' 'thunder storms' 'thunder storms and deaths' 'thunder storms and ilghting' 'thunder storms and lighting' 'thunder storms cd' 'thunder storms in the arctic arctic ' 'weather' 'thunder storms in winter' 'thunder storms on you tub' 'thunder storms pics' 'thunder storms with rain' 'thunderstorm' 'thunderstorm backgrounds' 'thunderstorm capital' 'thunderstorm capital 2008 dorfman' 'thunderstorm capital in boston' 'thunderstorm capital llc' 'thunderstorm capital of canada' 'thunderstorm capital of the us' 'thunderstorm capital of the world' 'thunderstorm facts' 'thunderstorm facts for kids' 'thunderstorm facts hail' 'thunderstorm facts tornadoes' 'thunderstorm mp3' 'thunderstorm mp3 download' 'thunderstorm mp3 download free' 'thunderstorm mp3 downloads' 'thunderstorm mp3 downloads free' 'thunderstorm mp3 files' 'thunderstorm mp3 free' 'thunderstorm mp3 free download' 'thunderstorm mp3 free downloads' 'thunderstorm mp3 torrent' 'thunderstorm mp3s' 'thunderstorm music' 'thunderstorm music cd' 'thunderstorm music downloads' 'thunderstorm music free' 'thunderstorm music playlists' 'thunderstorm music rain' 'thunderstorm pics' 'thunderstorm pictures' 'thunderstorm pictures for kids' 'thunderstorm safety' 'thunderstorm safety for kids' 'thunderstorm safety precautions' 'thunderstorm safety procedures' 'thunderstorm safety rules' 'thunderstorm safety tips' 'thunderstorm safety tips for kids' 'thunderstorm safety tips shelter' 'thunderstorm safety tips trees' 'thunderstorm sound effects' 'thunderstorm sound effects cd' 'thunderstorm sound effects download' 'thunderstorm sound effects free' 'thunderstorm sound effects free ' 'download' 'thunderstorm sound effects free music ' 'feature audio' 'thunderstorm sound effects mp3' 'thunderstorm sound effects rain' 'thunderstorm sounds' 'thunderstorm sounds cd' 'thunderstorm sounds download' 'thunderstorm sounds for sleep' 'thunderstorm sounds for sleeping' 'thunderstorm sounds free' 'thunderstorm sounds free download' 'thunderstorm sounds free downloads' 'thunderstorm sounds mp3' 'thunderstorm sounds mp3 download' 'thunderstorm sounds mp3 free' 'thunderstorm sounds online' 'thunderstorm sounds online for free' 'thunderstorm sounds online free' 'thunderstorm sounds sleep' 'thunderstorm sounds streaming' 'thunderstorm sounds torrent' 'thunderstorm soundscape' 'thunderstorm soundscapes' 'thunderstorm video' 'thunderstorm video clips' 'thunderstorm video download' 'thunderstorm video downloads' 'thunderstorm videos' 'thunderstorm videos for kids' 'thunderstorm videos lightning' 'thunderstorm videos online' 'thunderstorm wallpaper' 'thunderstorm warning' 'thunderstorm warning brisbane' 'thunderstorm warning definition' 'thunderstorm warning los angeles' 'thunderstorm warning san diego' 'thunderstorm warning san mateo county' 'thunderstorm warning santa barbara' 'thunderstorm warning santa clara' 'thunderstorm warning santa clara ' 'county' 'thunderstorm warning signal' 'thunderstorm warning signs' 'thunderstorm warning vs watch' 'thunderstorm warnings' 'thunderstorm warnings and watches' 'thunderstorm warnings for nj' 'thunderstorm warnings qld' 'thunderstorms' 'thunderstorms facts' 'thunderstorms facts for kids' 'thunderstorms for kids' 'tornados and thunder storms animated' 'understanding thunderstorms for kids' 'watch thunderstorm videos' 'weather underground forecast ' 'thunderstorms' 'what causes thunder storms' 'what is a thunder storm' 'where d thunder storms occur') TabOrder = 0 end object Memo2: TMemo Left = 240 Top = 8 Width = 265 Height = 129 Lines.Strings = ( 'Memo2') TabOrder = 1 end object Button1: TButton Left = 384 Top = 184 Width = 75 Height = 25 Caption = 'Button1' TabOrder = 2 OnClick = Button1Click end end

    Read the article

  • MySQL InnoDB Corruption after power outage, possible to recover?

    - by Tim Hackett
    Hey Guys, I recently started trying to get Redmine up and running after a power outage that seems to have corrupted our InnoDB database in MySQL. Redmine had an extensive set of documentation that I would like to get even if redmine isn't able to run. The service fails on startup. I have tried inserting innodb_force_recovery = 4 per the documentation from the url in the error log. (also tried 1 thru 6 as I have backed up all directories after the corruption) I have verified through "mysqld-nt --print-defaults" that it is starting with the recovery option in the params. The machine is running Windows Server 2003 SP2, Xeon E5335 with 2GB RAM, MySQL is not mirrored to another machine, nor is the machine a mirror. I do not have any backups because the previous person did not set them up. Here is the error log: InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 100308 14:50:01 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 100308 14:50:02 InnoDB: Error: page 7 log sequence number 0 935521175 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 2 log sequence number 0 935517607 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 11 log sequence number 0 935517607 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 5 log sequence number 0 972973045 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 6 log sequence number 0 972984051 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. 100308 14:50:02 InnoDB: Error: page 1577 log sequence number 0 972737368 InnoDB: is in the future! Current system log sequence number 0 933419020. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: for more information. InnoDB: Error: trying to access page number 4294965119 in space 0, InnoDB: space name .\ibdata1, InnoDB: which is outside the tablespace bounds. InnoDB: Byte offset 0, len 16384, i/o type 10. InnoDB: If you get this error at mysqld startup, please check that InnoDB: your my.cnf matches the ibdata files that you have in the InnoDB: MySQL server. 100308 14:50:02InnoDB: Assertion failure in thread 960 in file .\fil\fil0fil.c line 3959 InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.0/en/forcing-recovery.html InnoDB: about forcing recovery. 100308 14:50:02 [ERROR] mysqld-nt: Got signal 11. Aborting! 100308 14:50:02 [ERROR] Aborting 100308 14:50:02 [Note] mysqld-nt: Shutdown complete

    Read the article

  • How do you raise a Java BigInteger to the power of a BigInteger without doing modular arithmetic?

    - by angstrom91
    I'm doing some large integer computing, and I need to raise a BigInteger to the power of another BigInteger. The .pow() method does what I want, but takes an int value as an argument. The .modPow method takes a BigInteger as an argument, but I do not want an answer congruent to the value I'm trying to compute. My BigInteger exponent is too large to be represented as an int, can someone suggest a way to work around this limitation?

    Read the article

  • My EEEPc 900HA won't turn on/boot. Can it be fixed or does it need to be sent in?

    - by th3dude19
    My EEEPc 900HA stopped booting up out of nowhere. It went to sleep and when I went to wake it up, it wouldn't wake up. I powered down and went to power back up, but no go. The power light comes on solid and the battery/corded power light blinks consistently. There is no HDD activity or light activity. No BIOS. Just the lights described. I've troubleshooted the RAM, HDD, and internal power connections and everything checked out both on battery power and corded power. I've also reset the CMOS to no avail. What else can I do?

    Read the article

  • Wake On Lan only works on first boot, not sequent ones

    - by sp3ctum
    I have converted my old Dell Latitude D410 laptop to a server for tinkering. It is running an updated Debian Squeeze (6) with a Xen enabled kernel (I want to toy with virtual machines later on). I am running it 'headless' via an ethernet connection. I am struggling to enable Wake On Lan for the box. I have enabled the setting in the BIOS, and it works nicely, but only for the first time after the power cord is plugged in. Here is my test: Plug in power cord, don't boot yet Send magic Wake On Lan packet from test machine (Ubuntu) using the wakeonlan program Server expected to start (does every time) Once server has booted, log in via ssh and shut it down via the operating system After shutdown, wake server up via WOL again (fails every time) Some observations: Right after step 1 I can see the integrated NIC has a light on. I deduce this means the NIC gets adequate power and that the ethernet cable is connected to my switch. This light is not on after step 4 (the shutdown stage). The light becomes back on after I disconnect and reconnect the power cord, after which WOL works as well. After step 4 I can verify that wake on lan is enabled via the ethtool program (repeatable each time) This blog post suggested the problem may lay in the fact the motherboard might not be giving adequate power to the NIC after shutdown, so I copied an acpitool script that supposedly should signal the system to give the needed power to the card when shut down. Obviously it did not fix my issue. I have included the relevant power settings in the paste below. I have tried different combinations of parameters of shutdown (the program) options, as well as the poweroff program. I even tried "telinit 0", which I figured would do the most direct boot via software. If I keep the laptop's power button pressed down and do a hard boot this way, the light on the ethernet port stays lit and a WOL is possible. I copied a bunch of hopefully useful information in this paste I have tried this with the laptop battery connected and without it. I get the same result. Promptly pressing the power button causes the system to shut down with the message "The system is going down for system halt NOW!", and WOL is still unsuccessful.

    Read the article

  • How do I make changes to /proc/acpi/wakeup permanent?

    - by Jolan
    I had a problem with my Ubuntu 12.04 waking up immediately after going into suspend. I solved the problem by changing the settings in /proc/acpi/wakeup, as suggested in this question: How do I prevent immediate wake up from suspend?. After changing the settings, the system goes flawlessly into suspend and stays suspended, but after I wake it back up, the settings in /proc/acpi/wakeup are different from what I set them to. Before going to suspend: cat /proc/acpi/wakeup Device S-state Status Sysfs node SMB0 S4 *disabled pci:0000:00:03.2 PBB0 S4 *disabled pci:0000:00:09.0 HDAC S4 *disabled pci:0000:00:08.0 XVR0 S4 *disabled pci:0000:00:0c.0 XVR1 S4 *disabled P0P5 S4 *disabled P0P6 S4 *disabled pci:0000:00:15.0 GLAN S4 *enabled pci:0000:03:00.0 P0P7 S4 *disabled pci:0000:00:16.0 P0P8 S4 *disabled P0P9 S4 *disabled USB0 S3 *disabled pci:0000:00:04.0 USB2 S3 *disabled pci:0000:00:04.1 US15 S3 *disabled pci:0000:00:06.0 US12 S3 *disabled pci:0000:00:06.1 PWRB S4 *enabled SLPB S4 *enabled I tell the system to suspend, and it works as it should. But later after waking it up, the settings are changed to either: USB0 S3 *disabled pci:0000:00:04.0 USB2 S3 *enabled pci:0000:00:04.1 US15 S3 *disabled pci:0000:00:06.0 US12 S3 *enabled pci:0000:00:06.1 or USB0 S3 *enabled pci:0000:00:04.0 USB2 S3 *enabled pci:0000:00:04.1 US15 S3 *enabled pci:0000:00:06.0 US12 S3 *enabled pci:0000:00:06.1 Any ideas? Thank you for your response. Unfortunately it did not solve my problem. all of /sys/bus/usb/devices/usb1/power/wakeup /sys/bus/usb/devices/usb2/power/wakeup /sys/bus/usb/devices/usb3/power/wakeup /sys/bus/usb/devices/usb4/power/wakeup as well as /sys/bus/usb/devices/3-1/power/wakeup are set to disabled, and the notebook still wakes up by itself right after going to sleep. The only thing it seems to react to are the settings in /proc/acpi/wakeup, which keep changing (resetting) every time i power off/restart my notebook.

    Read the article

  • Microsoft&rsquo;s new technical computing initiative

    - by Randy Walker
    I made a mental note from earlier in the year.  Microsoft literally buys computers by the truckload.  From what I understand, it’s a typical practice amongst large software vendors.  You plug a few wires in, you test it, and you instantly have mega tera tera flops (don’t hold me to that number).  Microsoft has been trying to plug away at their cloud services (named Azure).  Which, for the layman, means Microsoft runs your software on their computers, and as demand increases you can allocate more computing power on the fly. With this in mind, it doesn’t surprise me that I was recently sent an executive email concerning Microsoft’s new technical computing initiative.  I find it to be a great marketing idea with actual substance behind their real work.  From the programmer academic perspective, in college we dreamed about this type of processing power.  This has decades of computer science theory behind it. A copy of the email received.  (note that I almost deleted this email, thinking it was spam due to it’s length) We don't often think about how complex life really is. Take the relatively simple task of commuting to and from work: it is, in fact, a complicated interplay of variables such as weather, train delays, accidents, traffic patterns, road construction, etc. You can however, take steps to shorten your commute - using a good, predictive understanding of a few of these variables. In fact, you probably are already taking these inputs and instinctively building a predictive model that you act on daily to get to your destination more quickly. Now, when we apply the same method to very complex tasks, this modeling approach becomes much more challenging. Recent world events clearly demonstrated our inability to process vast amounts of information and variables that would have helped to more accurately predict the behavior of global financial markets or the occurrence and impact of a volcano eruption in Iceland. To make sense of issues like these, researchers, engineers and analysts create computer models of the almost infinite number of possible interactions in complex systems. But, they need increasingly more sophisticated computer models to better understand how the world behaves and to make fact-based predictions about the future. And, to do this, it requires a tremendous amount of computing power to process and examine the massive data deluge from cameras, digital sensors and precision instruments of all kinds. This is the key to creating more accurate and realistic models that expose the hidden meaning of data, which gives us the kind of insight we need to solve a myriad of challenges. We have made great strides in our ability to build these kinds of computer models, and yet they are still too difficult, expensive and time consuming to manage. Today, even the most complicated data-rich simulations cannot fully capture all of the intricacies and dependencies of the systems they are trying to model. That is why, across the scientific and engineering world, it is so hard to say with any certainty when or where the next volcano will erupt and what flight patterns it might affect, or to more accurately predict something like a global flu pandemic. So far, we just cannot collect, correlate and compute enough data to create an accurate forecast of the real world. But this is about to change. Innovations in technology are transforming our ability to measure, monitor and model how the world behaves. The implication for scientific research is profound, and it will transform the way we tackle global challenges like health care and climate change. It will also have a huge impact on engineering and business, delivering breakthroughs that could lead to the creation of new products, new businesses and even new industries. Because you are a subscriber to executive e-mails from Microsoft, I want you to be the first to know about a new effort focused specifically on empowering millions of the world's smartest problem solvers. Today, I am happy to introduce Microsoft's Technical Computing initiative. Our goal is to unleash the power of pervasive, accurate, real-time modeling to help people and organizations achieve their objectives and realize their potential. We are bringing together some of the brightest minds in the technical computing community across industry, academia and science at www.modelingtheworld.com to discuss trends, challenges and shared opportunities. New advances provide the foundation for tools and applications that will make technical computing more affordable and accessible where mathematical and computational principles are applied to solve practical problems. One day soon, complicated tasks like building a sophisticated computer model that would typically take a team of advanced software programmers months to build and days to run, will be accomplished in a single afternoon by a scientist, engineer or analyst working at the PC on their desktop. And as technology continues to advance, these models will become more complete and accurate in the way they represent the world. This will speed our ability to test new ideas, improve processes and advance our understanding of systems. Our technical computing initiative reflects the best of Microsoft's heritage. Ever since Bill Gates articulated the then far-fetched vision of "a computer on every desktop" in the early 1980's, Microsoft has been at the forefront of expanding the power and reach of computing to benefit the world. As someone who worked closely with Bill for many years at Microsoft, I am happy to share with you that the passion behind that vision is fully alive at Microsoft and is carried out in the creation of our new Technical Computing group. Enabling more people to make better predictions We have seen the impact of making greater computing power more available firsthand through our investments in high performance computing (HPC) over the past five years. Scientists, engineers and analysts in organizations of all sizes and sectors are finding that using distributed computational power creates societal impact, fuels scientific breakthroughs and delivers competitive advantages. For example, we have seen remarkable results from some of our current customers: Malaria strikes 300,000 to 500,000 people around the world each year. To help in the effort to eradicate malaria worldwide, scientists at Intellectual Ventures use software that simulates how the disease spreads and would respond to prevention and control methods, such as vaccines and the use of bed nets. Technical computing allows researchers to model more detailed parameters for more accurate results and receive those results in less than an hour, rather than waiting a full day. Aerospace engineering firm, a.i. solutions, Inc., needed a more powerful computing platform to keep up with the increasingly complex computational needs of its customers: NASA, the Department of Defense and other government agencies planning space flights. To meet that need, it adopted technical computing. Now, a.i. solutions can produce detailed predictions and analysis of the flight dynamics of a given spacecraft, from optimal launch times and orbit determination to attitude control and navigation, up to eight times faster. This enables them to avoid mistakes in any areas that can cause a space mission to fail and potentially result in the loss of life and millions of dollars. Western & Southern Financial Group faced the challenge of running ever larger and more complex actuarial models as its number of policyholders and products grew and regulatory requirements changed. The company chose an actuarial solution that runs on technical computing technology. The solution is easy for the company's IT staff to manage and adjust to meet business needs. The new solution helps the company reduce modeling time by up to 99 percent - letting the team fine-tune its models for more accurate product pricing and financial projections. Our Technical Computing direction Collaborating closely with partners across industry and academia, we must now extend the reach of technical computing even further to help predictive modelers and data explorers make faster, more accurate predictions. As we build the Technical Computing initiative, we will invest in three core areas: Technical computing to the cloud: Microsoft will play a leading role in bringing technical computing power to scientists, engineers and analysts through the cloud. Existing high- performance computing users will benefit from the ability to augment their on-premises systems with cloud resources that enable 'just-in-time' processing. This platform will help ensure processing resources are available whenever they are needed-reliably, consistently and quickly. Simplify parallel development: Today, computers are shipping with more processing power than ever, including multiple cores, but most modern software only uses a small amount of the available processing power. Parallel programs are extremely difficult to write, test and trouble shoot. However, a consistent model for parallel programming can help more developers unlock the tremendous power in today's modern computers and enable a new generation of technical computing. We are delivering new tools to automate and simplify writing software through parallel processing from the desktop... to the cluster... to the cloud. Develop powerful new technical computing tools and applications: We know scientists, engineers and analysts are pushing common tools (i.e., spreadsheets and databases) to the limits with complex, data-intensive models. They need easy access to more computing power and simplified tools to increase the speed of their work. We are building a platform to do this. Our development efforts will yield new, easy-to-use tools and applications that automate data acquisition, modeling, simulation, visualization, workflow and collaboration. This will allow them to spend more time on their work and less time wrestling with complicated technology. Thinking bigger There is so much left to be discovered and so many questions yet to be answered in the fascinating world around us. We believe the technical computing community will show us that we have not seen anything yet. Imagine just some of the breakthroughs this community could make possible: Better predictions to help improve the understanding of pandemics, contagion and global health trends. Climate change models that predict environmental, economic and human impact, accessible in real-time during key discussions and debates. More accurate prediction of natural disasters and their impact to develop more effective emergency response plans. With an ambitious charter in hand, this new team is ready to build on our progress to-date and execute Microsoft's technical computing vision over the months and years ahead. We will steadily invest in the right technologies, tools and talent, and work to bring together the technical computing community. I invite you to visit www.modelingtheworld.com today. We welcome your ideas and feedback. I look forward to making this journey with you and others who want to answer the world's biggest questions, discover solutions to problems that seem impossible and uncover a host of new opportunities to change the world we live in for the better. Bob

    Read the article

  • How do I re-enable the backlight?

    - by Scott Severance
    Since Oneiric, if I leave my machine (HP Mini 110 netbook) unattended and it goes into power-save mode, the backlight gets disabled. How can I turn it back on? Note that the keyboard backlight controls (Fn+F4 and Fn+F3) don't have any effect in this situation. I've already filed a bug, but filing a bug doesn't fix my problem. I tried this workaround posted in this bug report dealing with Acer laptops: sudo setpci -s 00:02.0 F4.B=0 However, if anything, that command makes things worse. In the general case, I can see a little bit if I'm in a dark room with a flashlight aimed just so. But after running setpci I can't see anything. And I find the setpci documentation to be utterly incomprehensible, so I don't know whether I need to tweak my command somehow or whether I'm completely barking up the wrong tree. Update: I've found a workaround: I'm now booting with the kernel parameter acpi=off. This disables power management, which prevents the machine from going into power saving mode and thus failing to come back up correctly. Of course, not having power management means that I can't use suspend or do anything to manage power other than powering it off (even then, I have to manually use the power switch). Also, it prevents me from using Unity 3D or Gnome Shell, forcing me into Unity 2C or Gnome Classic. So, I'd really like to be able to stop using this hack.

    Read the article

  • nokia cell phone not accepting IP from dnsmasq dhcp server

    - by samix
    Hello, I having problem connecting a NOkia cell phone to my home wifi network. The wifi network is provided by a wireless card in a machine running Debian Testing and 2.6.26-2-686 kernel. The cars is D-Link DWL-G520 working in ap mode and has WPA encryption enabled. The wireless network is provided by hostapd using madwifi driver. Windows and Mac machines work properly with this wifi network. When I try to get the Nokia phone to connect to the wifi network, I get these lines in my dnsmasq log (to see lines without wrapping, here is the pastebin link for convenience - http://pastebin.com/m466c8fd2): Oct 27 13:25:21 red hostapd: ath0: STA 11:22:33:44:55:66 IEEE 802.11: disassociated Oct 27 13:25:21 red hostapd: ath0: STA 11:22:33:44:55:66 IEEE 802.11: associated Oct 27 13:25:21 red hostapd: ath0: STA 11:22:33:44:55:66 RADIUS: starting accounting session 4AE664FA-00000036 Oct 27 13:25:21 red hostapd: ath0: STA 11:22:33:44:55:66 WPA: pairwise key handshake completed (WPA) Oct 27 13:25:21 red hostapd: ath0: STA 11:22:33:44:55:66 WPA: group key handshake completed (WPA) Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 Available DHCP range: 192.168.5.150 -- 192.168.5.199 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 DHCPDISCOVER(ath0) 0.0.0.0 11:22:33:44:55:66 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 DHCPOFFER(ath0) 192.168.5.21 11:22:33:44:55:66 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 requested options: 12:hostname, 6:dns-server, 15:domain-name, Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 requested options: 1:netmask, 3:router, 28:broadcast, 120:sip-server Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 tags: known, ath0 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 next server: 192.168.5.1 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 1 option: 53:message-type 02 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 54:server-identifier 192.168.5.1 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 51:lease-time 00:00:46:50 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 58:T1 00:00:23:28 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 59:T2 00:00:3d:86 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 1:netmask 255.255.255.0 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 28:broadcast 192.168.5.255 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 3:router 192.168.5.1 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 6:dns-server 192.168.5.1 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 8 option: 15:domain-name home.pvt Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 3 option: 12:hostname NokiaCellPhone Anybody know the problem might be? If I switch off dnsmasq dhcp queries logging, i.e. if I decrease the verbosity of the log, all I see are two lines of DHCPDISCOVER(ath0) and DHCPOFFER(ath0) repeatedly in the log with no acceptance by the cell phone. It appears as though the phone is not accepting the dhcp offer. However, if I give the phone a static IP address in its configuration, it works properly on the wifi network. So it appears as though the problem is dhcp related. Hints? Suggestions? Installed stuff: $ dpkg -l dnsmasq hostap* | grep ^i ii dnsmasq 2.50-1 A small caching DNS proxy and DHCP/TFTP server ii dnsmasq-base 2.50-1 A small caching DNS proxy and DHCP/TFTP server ii hostapd 1:0.6.9-3 user space IEEE 802.11 AP and IEEE 802.1X/WPA/ Thanks. PS: Here is the DHCP tcp dump for more information (with mac addresses changed): $ sudo dhcpdump -i ath0 -h ^11:22:33:44:55:66 TIME: 2009-10-30 12:15:32.916 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 0 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:32.918 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 0 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:32.918 IP: 192.168.5.1 (a:bb:cc:dd:ee:ff) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 2 (BOOTPREPLY) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 0 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 192.168.5.21 SIADDR: 192.168.5.1 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 2 (DHCPOFFER) OPTION: 54 ( 4) Server identifier 192.168.5.1 OPTION: 51 ( 4) IP address leasetime 18000 (5h) OPTION: 58 ( 4) T1 9000 (2h30m) OPTION: 59 ( 4) T2 15750 (4h22m30s) OPTION: 1 ( 4) Subnet mask 255.255.255.0 OPTION: 28 ( 4) Broadcast address 192.168.5.255 OPTION: 3 ( 4) Routers 192.168.5.1 OPTION: 6 ( 4) DNS server 192.168.5.1 OPTION: 15 ( 8) Domainname home.pvt OPTION: 12 ( 3) Host name Nokia_E63 TIME: 2009-10-30 12:15:34.922 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 2 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:34.922 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 2 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:34.923 IP: 192.168.5.1 (a:bb:cc:dd:ee:ff) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 2 (BOOTPREPLY) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 2 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 192.168.5.21 SIADDR: 192.168.5.1 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 2 (DHCPOFFER) OPTION: 54 ( 4) Server identifier 192.168.5.1 OPTION: 51 ( 4) IP address leasetime 18000 (5h) OPTION: 58 ( 4) T1 9000 (2h30m) OPTION: 59 ( 4) T2 15750 (4h22m30s) OPTION: 1 ( 4) Subnet mask 255.255.255.0 OPTION: 28 ( 4) Broadcast address 192.168.5.255 OPTION: 3 ( 4) Routers 192.168.5.1 OPTION: 6 ( 4) DNS server 192.168.5.1 OPTION: 15 ( 8) Domainname home.pvt OPTION: 12 ( 3) Host name Nokia_E63 TIME: 2009-10-30 12:15:38.919 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 6 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:38.920 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 6 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:38.921 IP: 192.168.5.1 (a:bb:cc:dd:ee:ff) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 2 (BOOTPREPLY) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 6 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 192.168.5.21 SIADDR: 192.168.5.1 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 2 (DHCPOFFER) OPTION: 54 ( 4) Server identifier 192.168.5.1 OPTION: 51 ( 4) IP address leasetime 18000 (5h) OPTION: 58 ( 4) T1 9000 (2h30m) OPTION: 59 ( 4) T2 15750 (4h22m30s) OPTION: 1 ( 4) Subnet mask 255.255.255.0 OPTION: 28 ( 4) Broadcast address 192.168.5.255 OPTION: 3 ( 4) Routers 192.168.5.1 OPTION: 6 ( 4) DNS server 192.168.5.1 OPTION: 15 ( 8) Domainname home.pvt OPTION: 12 ( 3) Host name Nokia_E63 TIME: 2009-10-30 12:15:46.944 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: ccafe769 SECS: 14 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:46.944 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: ccafe769 SECS: 14 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:46.945 IP: 192.168.5.1 (a:bb:cc:dd:ee:ff) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 2 (BOOTPREPLY) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: ccafe769 SECS: 14 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 192.168.5.21 SIADDR: 192.168.5.1 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 2 (DHCPOFFER) OPTION: 54 ( 4) Server identifier 192.168.5.1 OPTION: 51 ( 4) IP address leasetime 18000 (5h) OPTION: 58 ( 4) T1 9000 (2h30m) OPTION: 59 ( 4) T2 15750 (4h22m30s) OPTION: 1 ( 4) Subnet mask 255.255.255.0 OPTION: 28 ( 4) Broadcast address 192.168.5.255 OPTION: 3 ( 4) Routers 192.168.5.1 OPTION: 6 ( 4) DNS server 192.168.5.1 OPTION: 15 ( 8) Domainname home.pvt OPTION: 12 ( 3) Host name Nokia_E63 TIME: 2009-10-30 12:15:48.952 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 ... and so on ...

    Read the article

  • Wifi Direct P2P-go and P2P-client support in ubuntu

    - by giri
    I am trying to get wifi direct working on a laptop with ubuntu 12.04 When I type the command 'iw list' it doesn't show P2P-client or P2P-go under 'supported interface modes.From http://wireless.kernel.org/en/users/Documentation/iw/replace-iwconfig I found that 'iwconfig' was replaced with 'iw'.Does it mean that my hardware doesn't have support for wifi-direct or is it just the software(drivers) issue? If is it just sofware issue please help me to find the right drivers which support wifi-direct. Here is the info about my ethernet controller from the output of 'lspci' 02:00.0 Ethernet controller: Atheros Communication Inc. AR242x / AR542x Wreless Network Adapter (PCI-Express) (rev 01) 06:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8055 PCI-E Gigabit Ethernet Controller (rev 13)

    Read the article

< Previous Page | 59 60 61 62 63 64 65 66 67 68 69 70  | Next Page >