Search Results

Search found 6972 results on 279 pages for 'usb sata'.

Page 64/279 | < Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >

• Ubuntu 11.10 USB 3.0 HDD

  - by Chazm

  I have a problem with my external HDD (WD My Book Essential 1TB) working on USB 3.0 port. I'm using dual boot setup with Windows 7 and Ubuntu 11.10, both 64 bit. While I'm running Windows and rebooting back to Windows everything works well. When I'm switchin to ubuntu everything works great as well. But after 1st reboot from ubuntu neither windows nor ubuntu mount the external drive. I have to reboot the device manually. I suspect that the problem is with unmounting the device on shutdown on ubuntu. The case concern only usb 3.0. When i plug the same device into usb 2 port the problem doesn't persist. Does any1 hit the same problem or have a clue what might goin wrong?

  Read the article

• fedora 11 server won't boot from SATA disk, won't boot from CD, BIOS configuration problems

  - by Tom

  Hi all, Yesterday our fc11 file/print server didn't boot, and had stopped on the BIOS page with a configuration problem. (with a distinct lack of foresight) I reset the BIOS settings to default without recording the message and booted the server. The server ran until it was to be booted this morning, and it was failing to mount the root partition from the SATA disk. It also failed to boot from a known good diagnostics CD. After a few more tries, it now fails part way through the Phoenix - AwardBIOS screen where it is listing the SATA/IDE devices, and it is showing garbage for the identity of one of the disks, which should actually be "none" It looks like the motherboard has gone kaput. The motherboard is an EVGA NF790i, are there any diagnostic tools that I can use to determine this? (as I would prefer to not send the motherboard back, only to discover that it is the RAM or the CPU) ps I can't get it to boot from the memTest disk, so I can't run that diagnostic. Thanks!

  Read the article

• VMWare ESX installation on sata disk

  - by ilansch

  I have a PC with Gigabyte H77 motherboard with Intel I5-3550 CPU 8 GB RAM 1600MHz and a 500GB Harddisk (7200RPM) - WD Sata III disk I wish to install esx on it and run some virtual machines on it. not alot, something like 2-3 VMs. My hardisk is Sata, is it possible to install ESX Server on it ? I am not worried about loading issues. When i try loading the installation it writes it cannot detect my disk (since its not SCSI disk). How can i bypass this ? or find a solution. thanks

  Read the article

• Solaris 10 5/09 can't find SATA disk

  - by anon

  We need to run standard Solaris 10 on a few development servers (Dell 530s) because we can't get a commercial application running on OpenSolaris (we're still trying). However, we are finding that sometimes when Solaris 10 goes to do the install, after setup screens, it can't find the SATA drive. We tried the BIOS setting described here: BigAdmin On some Dells 530s, Solaris GA installs fine, but on others it doesn't. OpenSolaris always installs. Is there some way we can determine (eg. installing OpenSolaris and examining the SATA driver used) what OpenSolaris detected and use some option or driver from it to get Solaris 10 installed on our development Dell servers?

  Read the article

• Add SATA Port to Motherboard?

  - by YAS

  I recently took off the bottom covers to my laptop, an Aspire 6930, and one of the covers was hiding an empty space large enough for a second hard drive. The bit of motherboard that was showing had the solder joints for a SATA port, but no port. What I'm wondering is; If I get a spare SATA port and solder it in would it mess up my motherboard and kill my laptop? I'm not concerned about a clean solder job, I can do that. But if the port is soldered in cleanly if there would be any danger to doing it. It'd be pretty darn awesome to get a second hard drive in my laptop.

  Read the article

• Internal SATA hard disk shows up as removable device on Windows 7

  - by neutron80k

  I am running Windows 7 on an Acer Aspire M7720 with three internal SATA drives; drive #2 and #3 are on a removable HDD rack. Drive #3 (on the second removable HDD rack) shows up as removable device in the system tray. If I take drive #3 and put it in the first rack, it shows up as an internal drive. If I put any other drive in the second removable rack, that drive is also shown as removable device. I would like to fix that so that the drive in the second removable rack also is listed as internal drive. Since this seems to be independent of the actual drive in the rack, I checked the BIOS, but that third SATA port uses the same configuration as the second rack. So far, I could not find a solution for this problem (it's really more an annoyance than a problem), any ideas are welcome.

  Read the article

• Can I use PCI SATA Addon card and Boot from a HDD attached to the card

  - by POTHEN

  Can I boot from a HDD which is running from a PCI SATA expansion card.

  Read the article

• Ubuntu 12.10 64 bits not booting on a Dell Inspiron 15z Puissance (French) in UEFI mode

  - by NicoGuich

  When trying to start Ubuntu from my USB key in UEFI mode (it works in Legacy mode, but I have to keep Windows) on a Dell Inspiron 15z , Grub starts, but when I choose any option, I get a black screen and my USB key stop teling me it is being read. EDIT: when using the legacy mode and trying to install Ubuntu, I get a blank partition table with Ubiquity… … and a very strange partition table from GParted (I have a hybrid 32Go SSD + 500Go HDD disk) :

  Read the article

• Why wont Ubuntu recognize Rogers LTE Rocket stick 330U Sierra wireless modem?

  - by rob lawson

  I tried to plug the rocket stick into the USB slot, and Ubuntu does not recognize that there is anything in the drive. I plug in a standard USB thumbdrive and it is recognized right away. Are there any applications to help me open the rogers folders to see the files, and maybe connect to the Internet using said rocket stick 330U? I've been searching for this answer for almost a week now, seems no one knows how to get the net using this piece of technology.

  Read the article

• Access files on Samsung Galaxy S3 external sd card using ubuntu 12.04

  - by nense

  I have a Samsung Galaxy s3 running the stock Samsung ROM and I'm trying to transfer files - videos, photos, music and downloads, from my handset to my system via USB running Ubuntu 12.04. I have followed to links suggested How to connect Samsung Galaxy S3 via USB? But it all goes over my head. Can anyone help me with a simple GUI program or a link so I can simply copy and paste selected files from my phone onto my system?

  Read the article

• lsusb - where device description comes from

  - by tommyk

  For one of my attached USB devices (2773:0104) I see no description in lsusb command output: user@Thinkpad-Laptop:~/binaries$ lsusb Bus 008 Device 002: ID 0a5c:217f Broadcom Corp. Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 036: ID 2773:0104 Where USB description is comming from, is it from device driver or is it stored in the hardware itself ?

  Read the article

• 2 internet connections

  - by oshirowanen

  If I have a wireless and a usb internet connection on my Ubuntu 12.04 as in: At the moment, Ubuntu seems to only make use of the Wired connection which is the usb connection. Is it possible to get ubuntu to use the wireless connection without unplugging the wired connection? So basically, as will, I would like to switch between the connections without unplugging any of them while leaving them both enabled. Is this possible?

  Read the article

• Can't access any storage devices on 12.10

  - by Trigger

  Hi I've just started using Ubuntu 12.10 (today!) my first time with any non-windows OS. I wanted to retrieve some files after windows stopped working. I boot Ubuntu from a USB and it seems to work fine - I can access the internet etc. But I can't access any of my drives or even a USB drive. The error I get is "Adding read ACL for uid 999 to `/media/ubuntu' failed: Operation not supported" Any help much appreciated:)

  Read the article

• "Can't find root filesystem / error mounting /dev/root" when booting to new kernel

  - by salparadise

  I am trying to upgrade my kernel from 2.6.18-274 to 2.6.39 for some wireless card drivers. When I boot into the new kernel I get the "Can't find root filesystem / error mounting /dev/root" googling led me to this page http://fedoraproject.org/wiki/Common_kernel_problems#Can.27t_find_root_filesystem_.2F_error_mounting_.2Fdev.2Froot From what I am reading seems to be an issue with a driver for my SATA controller or HD, but I can't find what option I need to add to the kernel. Doing a diff from the old initrd to the new one gives me the following: root-> diff /tmp/kafter /tmp/kbefore 6a7,8 > lib/dm-message.ko > lib/dm-region_hash.ko 8a11 > lib/dm-raid45.ko 13d15 < lib/dm-region-hash.ko 16a19 > lib/dm-mem-cache.ko Do I need any of those? not sure if I would need dm-raid45.ko as I am not running a raid. I have the same SATA and IDE options configured for both kernels so not sure what else to look for, any help is appreciated. Additionally here is the HW info: 00:1f.2 IDE interface: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Controller (rev 03) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Hewlett-Packard Company Unknown device 3006 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 233 I/O ports at 1818 [size=8] I/O ports at 1830 [size=4] I/O ports at 1820 [size=8] I/O ports at 1834 [size=4] I/O ports at 14f0 [size=16] Capabilities: [70] Power Management version 2 root-> smartctl -a /dev/sda ... === START OF INFORMATION SECTION === Device Model: WDC WD5000AADS-00S9B0

  Read the article

• How should I configure grub for booting linux kernel from a USB hard drive?

  - by skolima

  I have a laptop hard drive in an external enclosure which I use as a large pendrive. For an added twist, I have installed Linux on it, so I can boot any machine with my distribution of choice (e.g. for data recovery or repairing a b0rked system or just using a borrowed laptop without destroying the preinstalled Windows). The problem is that, depending on the hardware configuration, the USB hard drive may be visible under different paths. For grub configuration I just use (hda0,0) as it is relative to the device the grub was launched from. I have UUID entries in /etc/fstab. I also specify rootwait in the kernel parameters so that it waits for the USB subsystem to settle down before trying to mount the device. What should I pass to the kernel as root= ? Currently boot from the pendrive once, check the debug messages to see what /dev/sdX device has been assigned to the USB drive by the kernel, then reboot and edit the grub configuration. I can't change anything on the PC besides enabling Boot from USB hard drive in BIOS and setting it to higher priority than internal hard drives. There are various initrd generating scripts which include support for UUID in root device path, unfortunately the Gentoo native one (genkernel) does not support rootwait and I had no luck trying to use others. The boot process goes like this (it is quite similar in Windows): The BIOS chooses the boot device and loads whatever is its MBR (which happens to be grub stage-1). Grub loads it's configuration and stage-2 files from device it has set as root, using (hd0) for the device it was loaded from by BIOS. Grub loads and starts a kernel (still the same numbering, so I can use (hd0,0) again ). Kernel initializes all built-in devices (rootwait does it's magic now). Kernel mounts the partition it was passed as root (this is a kernel parameter, not grub parameter). init.d starts the userland booting process, including mounting things from /etc/fstab. Part 5 is the one giving me problems.

  Read the article

• Ubuntu 12.04 install DVD-RW recorder PATA as SCSI

  - by Alexandre Gatelli

  Ubuntu 12.04 64-bit installed DVD-RW recorder PATA as SCSI. My DVD-RW recorder is in /dev/sr0 as SCSI. I opened Disk Management and my IDE PATA drive is installed as SCSI. I can't use this drive because it hangs computer (I need press reset button on CPU to back to Ubuntu). What do I do for the drive back to function with the correct drive (IDE mode)? With the first kernel version of the Ubuntu 12.04 64-bit was all functioning. Help me please.

  Read the article

• Why Both 8GB USB Flash Drives Have Different Integrities?

  - by Boris_yo

  USB 3.0 SuperTalent Express DUO 8GB recently had its partition corrupted and declared itself "write-protected" and I was told in chat by @sidran32 that this usually means that flash drive gone bad due to writing cycles limit being reached. Having this thumbdrive for over a year being used infrequently, I was in doubt and referred to SuperTalent's support. I was given recovery tool which I executed but it failed first time prompting me to reinsert it. After that, I formatted it with Windows 7 integrated format utility since recovery tool offered to do this as well which was successful. The problem as I have noticed is with integrity of SuperTalent: Compare above to SanDisk's Micro Cruzer 8GB: Am I missing something? Both thumbdrives are of 8GB and have same FAT32 file system.

  Read the article

• How many times can data be read from a USB flash drive?

  - by John

  While I am aware that performing writes on a USB flash drive degrades the life expectancy of the device. I have heard the quantity of writes is anywhere from 100 thousand to 10 million, but I have not heard about number of read operations. Does reading from the device count toward this total? I am interested in writing only once to a flash drive and setting it to read-only. Then reading files from the device a thousand or more times per day, but am wondering if (at say 1,000 reads per day), the flash drive will need to be replaced within 100 days (assuming a 100,000 r/w cycle lifetime)?

  Read the article

• connecting to bsnl wll, with huawei fixed wireless modem with connected to usb port on linux mint.

  - by Rakesh

  On windows, when I plugged in the usb connector, to the device was recognized as a mass storage device and installed all the drivers, to my computer, then the device, automatically restarted and started behaving like a modem, I'm writing this post, using the same modem, through windows... On linux mint (debian kernel, similar to ubuntu 8.10), the device is recognized as a mass storage device, some times, but, has no programs, useful for linux... When I use the modem on windows and restart the computer and login to linux, the device shows up as "not yet configured" in the terminal command "lsusb"... I googled a lot for solutions, tried many things, atlast, configured it and run the command "wvdial". But, get the error, that the modem is not responding, at last ! :'( Please help me out... Many more people are facing this problem, as I could discover, when I googled for it. this is the website address of huawei, the company of my modem... "www.huawei.com" Specification: model: ETS1220 FEQ: 800M Thank you.

  Read the article

• How can I format a USB "thumb drive" so it will be readable on OS X and Windows?

  - by Ethan

  I have an OS X system. I want to use it to put some files on a USB drive and then be able to loan the drive to Mac and XP and Vista users so they can get the files off it. I also need to wipe the drive clean first to make sure there's nothing sensitive on it by accident because I'm going to be passing it around. What the name of the filesystem format I want? What's the procedure? Command line operations are fine.

  Read the article

• How do you partition a USB Thumb / Flash Drive?

  - by Omar Shahine

  Out of the box, Windows will not allow you to partition a USB Thumb / Flash Drive. How can you do this? In case anyone is wondering Why you would do this? It's interesting in the case of a BitLocker ToGo drive where you can take a large thumbdrive (like 4 or 8 GB) and format a small amount of the drive to be used normally as a Fat32 drive and leave the remaining partition encrypted using BitLocker. This allows you to keep some non secret data on the unencrypted partition(like portable apps).

  Read the article

• Windows XP waits for usb drive on almost every operation.

  - by Tomasz Kowalczyk

  Hello everyone, I have a problem with my Windows XP operating system, particularly with the USB device that is plugged in - 1TB WD My Book external drive. I haven't found any information about such behaviour when searching in Internet, so I have to ask You. The problem is: when I am using computer, especially during work (programming), when I try to access any information on a hard disk ("internal" one), Windows seems to "consult" it with the external drive. For example, when I open file selection dialog window, if I try to change directory, system activates external drive, reads something (I hear the disk's operational noise) and after some seconds of such pause it makes the operations I requested. There are many situations in which I can reproduce this behavior - opening My Computer, shutting down system, opening partition folder from My Computer - every operation involves the usage of external drive. Please understand me properly - this is not something that happens EVERY time, but at least "many" times a day. What causes such behavior and how can I "turn off" external drive when it's not needed? Thanks in advance for your answers.

  Read the article

• How can I recover [data from] my failing USB key?

  - by moe37x3

  I have a Corsair Flash Voyager USB key, and it's almost completely failed. When I plug it into my [WinXP] computer, the OS mounts it and open up explorer to the drive's root directory. However, if I try to copy any data off, I get an error message saying that the device is not there. If I leave it plugged in, the OS seems to oscillate between seeing it and not seeing it, since the "Safely Remove Hardware" tray icon appears and disappears every few seconds. The damage was probably caused by my abuse, either from plugging it in with my keys hanging off of it or from losing the cap and keeping it in my pocket uncapped. Is there anything I can do to save the data from it or even rehabilitate the drive?

  Read the article

• How to automatically show USB camera or memory stick contents in Icewm?

  - by darenw

  I normally use a very lightweight Linux setup. No desktop like Gnome or KDE, just Icewm as the windows manager and nothing else that normal users might consider essential. Well, I do need a file manager - I use Thunar. Recently I've been trying Gnome. Whenever I shove a memory stick into a USB port, or connect my digital camera, it can automatically pop up a file manager showing all the goodies on that device. KDE does this too. I like this. Although quick at the command line, I like not having to go sudo to mount the device and all that. If I want to stick with a lightweight setup using Icewm+Thunar, is there something non-huge I can install to make external devices fire up a Thunar window, or otherwise make access to the contents brainlessly easy?

  Read the article

• Where exactly does a portable app is running when the usb stick is pulled out without closing that app?

  - by Selin Peck

  Where exactly does a portable app is running when the usb stick is pulled out without closing that app? Is it in memory? Is it written the on hard disk as temporary files (where exactly is it, appdata or where)? Does that mean the next user of the pc could gain access just clicking that from the system tray and saving to other folders? How about when the system crash and that portable app is not closed the normal way? On the next open, will it stay somewhere on temporary folders?

  Read the article

< Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >