Search Results

Search found 2858 results on 115 pages for 'pop ups'.

Page 65/115 | < Previous Page | 61 62 63 64 65 66 67 68 69 70 71 72  | Next Page >

• WOL doesn't work if set to anything other than `a` but this setting makes it boot all the time

  - by Elton Carvalho

  I manage a small "cluster" of 4 Xeon machines with Intel boards in my lab. They are all plugged to a 5-port 3-Com switch with static IP addresses like 10.0.0.x. They are all running OpenSuse 11.4 and their /home/ is served by one of the machines (node00) via NFS. They are plugged to an UPS that can keep them on for ca. 15 minutes, but there are lots of electric shortages due to "unscheduled maintenace" that are longer than this. So they end up being powered down without notice. If I set the BIOS to turn them on after power shortages, the issue is that they all boot at the same time and, if node00 decides to run fsck in the /home/ partition, it does not finish booting before the others try to NFS mount their /home/. I am trying to make wake on lan work, so I can choose to boot the NFS clients only after the server has successfully booted. The problem is that when I run ethtool I get an output like this: Supports Wake-on: pumbag Wake-on: g Theoretically, it is set to wake on MagicPacket(tm), according to the manual. But sending the WOL packet using wol -i 10.0.0.255 $MACADDR does not wake up the box after I shut it down with halt. The ethernet link led blinks after I send the packet, so it appears to be getting to the machine. However, if I set it up with ethtool -s eth1 wol bag, the machine always wakes up right after halting, even if I don't send the Magic packet. This means that the device can wake up with LAN activity, but seems to be ignoring the magic packet. Setting wol ag does not wake the box with the MagicPacket. Does setting wol a mean that it should boot with any broadcast message? How can I diagnose the issue of the machine not waking up with the MagicPacket even though I am sending it and it's set up to wake up with it? Thanks in advance!

  Read the article

• How to verify power provided to processors is clean

  - by GregC

  Once in a blue moon, I am seeing a blue screen of death on a shiny new Dell R7610 with a single 1100 Watt Dell-provided power supply on a beefy UPS. BCode is 101 (A clock interrupt was not received...), which some say is caused by under-volting a CPU. Naturally, I would have to contact Dell support, and their natural reaction would be to replace a motherboard, a power supply, or CPU, or a mixture of the above components. In synthetic benchmarks, system memory and CPU, as well as graphics memory and CPU perform admirably, staying up for hours and days. My questions are: Is power supply good enough for the application? Does it provide clean enough power to VRMs on the motherboard? Are VRMs good enough for dual Xeon E5-2665? Does C-states logic work correctly? Is there sufficient current provided to PCIe peripherals, such as disk controllers? P.S. Recently, I've gone through the ordeal with HP. They were nice and professional about it, but root cause was not established, and the HP machine still is less than 100%, giving me a blue screen of death once in a couple of months. Here's what quick web-searching turns up: http://www.sevenforums.com/bsod-help-support/35427-win-7-clock-interrupt-bsod-101-error.html#post356791 It appears Dell has addressed the above issue by clocking PCIe bus down to 5GT/sec in A03 BIOS. My disk controllers support PCIe 3.0, meaning that I would have to re-validate stability. Early testing shows improvements. Further testing shows significant decrease in performance on each of the x16 slots with Dell R7610 with A03 BIOS. But now it's running stable. HP machine has received a microcode update in September 2013 SUM (July BIOS) that makes it stable.

  Read the article

• TLS_REQCERT and PHP with LDAPS

  - by John

  Problem: Secure LDAP queries via command-line and PHP to an AD domain controller with a self-signed certificate. Background: I am working on a project where I need to enable LDAP look-ups from a PHP web application to a MS AD domain controller that is using a self-signed certificate. This self-signed certificate is also using a domain name that is not a FQDN - think of something like people.campus as the domain name. The web application would take the user's credentials and pass them on to the AD domain controller to verify if the credntials are a match or not. This seems simple, but I am having problems trying to get PHP and the self-signed certificate to work. Some people have suggested that I changed the TLS_REQCERT variable from "request" to "never" within the OpenLDAP configuration. I am concerned that this might have larger implications such as a man-in-the-middle attack and I am not comfortable changing this setting to never. I have also read some places online where one can take a certificate and place it as a trusted source within the openldap configuration file. I am curious if that is something that I could do for the situation that I have? Can I, from the command line, obtain the self-signed certificate that the AD domain controller is using, save it to a file, and then have openldap use that file for the trust that it needs so that I do not need to adjust the variable from request to never? I do not have access to the AD domain controller and as a result cannot export the certificate. If there is a way to obtain the certificate from the command line, what commands do I need to use? Is there an alternate method of handling this issue that would be better in the long run? I have some CentOS servers and some Ubuntu servers that I am working with to try and get this going on. Thanks in advance for your help and ideas.

  Read the article

• Vista - perform scheduled actions only if screen is not locked

  - by Syntax Error

  Ok, here's the general idea of what I want to do. After a certain time, I would like the computer to nag me to go to sleep. Maybe every five minutes or so. But I don't want the messages to pop up if the screen is locked, because I leave it like that all night. Ideally I would like to be able to do more things like shut down running instances the web browser, or lock my user session if I ignore the notices for too long. But I'm happy with just popup messages if that's all I can do. So, how much of this is possible and where do I start? I'm not too well versed with task scheduler, and I'm assuming I'll use that to at least start whatever script I have to put together.

  Read the article

• Recommend a mail server setup for multiple domains

  - by Greg

  Hi all, I've just set up a new Debian web server which I have done plenty of times before, but I want to add a mail server which I have never done before. I am aware of this question, but I would like someone to recommend packages and briefly explain how to use them for providing pop/imap access on multiple domains, a concept that has confused me for a while. I'm planning for this server to grow slowly but surely, from serving an initial 5 or 6 domains to about 20 in the first year, continuing at this rate. (yes, I've jumped on the cloud bandwaggon). At the moment, I have a DNS-A record pointing to my server's IP and nothing else. I'm assuming that I need a DNS-MX record pointing there too, but I haven't read up about it yet so today that's what I'll be doing. Hopefully reading up on the subject and the help that I get here will get my server up and running in no time. Thanks!

  Read the article

• Setting Up Local Repository with TortoiseSVN in Windows

  - by Teno

  I'm trying to set up a local repository so that all commitments are copied to the local destination, not a remote server. I followed this tutorial. What I did. Created a folder named "SVN_Repo" under C:\Documents and Settings[user-name]\My Documents\ Right clicked on the folder and chose TortoiseSVN -> Create repository here Clicked OK in the pop up dialog asking whether to create a directory structure. Created a folder named Repos for the local destination, under E:\ Right clicked on the SVN_Repo folder and chose SVN Checkout... Typed file:///E:\repos in the URL of repository field and clicked the OK button. What I got: Checkout from file:///E:/repos, revision HEAD, Fully recursive, Externals included Unable to connect to a repository at URL 'file:///E:/repos' Unable to open an ra_local session to URL Unable to open repository 'file:///E:/repos' I must be doing something wrong. Could somebody point it out? Thanks.

  Read the article

• Is there a lightweight MTA for Ubuntu 9.10 Desktop?

  - by Joe Casadonte

  I'm writing a Perl script to run as a cron job, and I want to email results & errors to a local account on the laptop. I'd like something that can talk SMTP (do any MTAs not adhere to SMTP?). I use Thunderbird 3, so I'll also need a POP/IMAP server (unless T-Bird can read straight from an mbox file; I'll have to check into that). No need for spam controls as I'll lock it down real tight, only accepting mail originating from the laptop itself. Thanks!

  Read the article

• XP Install Driver Notification for AirCard

  - by Brian

  Hello, A co-worker of mine is using an air-card; it prompted him to install software in the notification tray; he clicked on the wrong thing and the icon went away without him installing that software. How can I get that icon back? He can't install the software then... I know that you can download the software from the site, but we did that and were having issues from that too, was hoping to be able to install the sofware on the air card... Restarting and trying again doesn't pop up the notification too. Thanks.

  Read the article

• Thunderbird 16.0.1 with IMAP on Gmail on Windows 7

  - by Joe M

  My Thunderbird Trash folder is messed up and it does not get fixed by "Repair Folder". When I delete a message it goes into the Trash folder but if I try to access the message, I get a pop-up error message: The current operation on Trash did not succeed. The mail server for account for the XXX imail Gmail account responded: Some messages could not be FETCHed The message count in the Trash folder continues to increase. If I look in the Gmail trash folder I can read the deleted messages. Unlike other users that have reported this problem I cannot find a corrupted message in the Gmail Trash folder. In fact I do not find any corrupted messages in my any of Gmail labels.

  Read the article

• startx error no desktop manager

  - by WikiWitz

  I have Backtrack 5R2 KDE. I started recovery mode and did a failsafe xorg configuration. After that, I cannot load the KDE manager when I enter the startx command after logging in. Whenever I do a startx command (as root), the result resembles the following: This is not the actual output (I just drew this with MS paint because I cannot do a printscreen). The screen is just black with the icon in the upper left corner. The other pop-up menu appears when left-clicking the mouse. I tried the cp xorg.conf.failsafe xorg.conf advice from other websites with no luck. I have also tried the 'reconfigure option(s)' form the recovery mode with no success.

  Read the article

• webmail suite recommendation

  - by hoball

  Hello, I have serveral emails in a few domains (email@domain1, email@domain2, email@domain3). Currently they are on an owned email server and I am collecting emails via IMAP protocol (i would not like to use POP..) in Thunderbird. I have a few partners and I want to allow them to access the same email address. Here is what I desired: All users can open All the inboxes via IMAP @ Thunderbird (with proper configuration) at the same time, there are a webmail system, every user can login their account (userA, userB, userC), and they will see all inboxes (email@domain1, email@domain2, email@domain3) Would you recommend any suite that fits my needs? Either (a system to be installed on my server) or (a remote service where I need to config MX records) will do. Thank you.

  Read the article

• Site Goes Offline Every Day At Midnight - No One Knows Why

  - by HollerTrain

  0 down vote favorite Seems today a website I manage has been going online and offline between 12a and 12:25a. I have no idea what is causing the issue so I am seeking guidance on where to start. It is a Wordpress based site. So here is what I DO know: I have a pingdom account which alerts me when the site goes offline so we can see every day, like clockwork, the site goes on/off. At the time of the ups/downs I see a lot of strain on the memory usage. Look at the load average when the site is going online/offline (http://screencast.com/t/BRlfXkqrbJII). Then I ran this command to restart http (http://screencast.com/t/usVtYWZ2Qi) and the memory usage then goes down to this (http://screencast.com/t/VdTIy3bgZiQB). An hour after I restarted http, the site then went offline/online so restarting the http didn't do much help. When the site is going offline/online, I ran the top command and get this (http://screencast.com/t/zEwr7YQj3). Here is a top command when the site is at it's lowest (http://screencast.com/t/eaMfha9lbT - so this would be dubbged "normal"). Here is a bandwidth report (http://screencast.com/t/AS0h2CH1Gypq). The traffic doesn't seem to be that much (http://screencast.com/t/s7hrWNNic1K), but looking at my times the site is going up/down this may be one of the reasons? I have the dvp Nitro package at Media Temple (http://mediatemple.net/webhosting/nitro/). So at this point I would request some help in trying to figure out what the cause of this is, and how I can go about pinpointing this issue. ANY HELP is greatly appreciated.

  Read the article

• Why is Firefox so slow and heavy?

  - by Tony

  For some reason, when I go to links the pages seem slow and heavy. It also has a lot of lag spikes between page loads. Basically it seems to freeze then load it all at once fast. I'm currently using Firefox 25. But when I use the same Chrome version, it seems to be very fast and smooth page loading. The CPU it takes on average is about 400,000k. Extensions: iMacros Leethax Ad Block Plus 2.4 Ad Block Plus Pop-up Addon 0.9.1 Computer stats: 6 GB RAM Windows 7 Acer Aspire Laptop 500 GB HDD Intel Core i4-2370M How do I make Firefox load like Google Chrome, without much freezing?

  Read the article

• Clone a Red Hat RAID as part of a disaster recovery plan

  - by Campo

  I am looking for recommendations to clone a Red Hat mirrored raid to a single hard drive located in the same machine. The idea is if the servers hardware ever has an issue we have a similar hardware machine ready to go. All we would have to do is pop in the cloned drive. If the servers RAID ever failed we could just switch to the single drive to maintain uptime and restore the original configuration on the spare server with a backup. This is a restaurant and they are open 7 days a week. We do have time from 12:am to 9:00am to perform the necessary steps for a clone and we talking about under 10 Gigs of information. There is a database on the server. I have looked into Rsync and Clonezilla. But I am just not confident either is capable of completing the task I want. Looking for some suggestions and possibly a step by step if you could be so kind.

  Read the article

• Recommended resource to understand Internet conventions IPs, CNAMES, *, MX etc

  - by Petras

  I am a programmer who has been creating websites for many years in shared hosting environments. To make the website live, I logged into where the domain was hosted and updated the name servers. Sometimes I didn’t want POP email so I changed an A record. I never really understood what this meant but it worked. Now we have a dedicated server and I have to fill out all this to make it live: Plus I was told I had to complete zones at my domain host: I would really like to know what all this means. What is a * record What is an @ How does the internet work regarding all these conventions? Is there a good approachable book on this topic?

  Read the article

• Exchange 2010 Multiple accounts in one mailbox

  - by durilai

  I am looking for best practice or recommended ways of doing the following: I have a user that has 2 email addresses, he accesses them via POP 3 and OWA. He need to be able to send as each of the addresses. I do not want to create multiple AD accounts or mailboxes, but would like to be able to provide that visual separation. Is this possible, I know using Outlook I am able to add multiple POP3 accounts and he can send from whichever he choose, but how to enable this is OWA, as well as on a mobile using POP3. Thanks

  Read the article

• What's the best way to clone multiple PCs from one machine?

  - by Jason T.

  Where I work we have dozens and dozens of old ThinkPad laptops. A lot of these can be reused but not for our needs. They have been long since replaced. The higher-ups have decided to donate them to charity. For better or for worse I have been tasked with reimaging them. I took a laptop and installed the factory copy of Windows, updated it, configured it appropriately. Now I'm trying to reimage it to dozens of other laptops. What's some good software to do this? First I used clonezilla to clone the hdd in the laptop to an internal drive in an external enclosure and it worked. Then I tried taking the base image out and connecting it externally to a laptop that needed to be imaged and I got it to work a few times. So far so good, right? Well once I informed my boss of my findings and what I would want to do then the images started to not work on new laptops. One of three things would happen: The Thinkpads would just blink at me and Windows wouldn't load. Or Windows would load but freeze within two minutes. Last but not least the laptops would BSOD during the Windows XP bootup. These laptops are not going to be used by the company. They're going to charity. So can anyone else recommend a way to reimage multiple laptops?

  Read the article

• USB keyboard not working under Windows 7 x64?

  - by Comboo

  I have two USB keyboards, one no-name cheap thing and an old Logitech. When I plug them in to my computer they pop up in Device Manager as an "Unknown device" and "USB-receiver", respectively. Both of them fail to install any drivers, neither automatically or through Windows Update. Both keyboards work perfectly on another computer I have with Windows Vista 32-bit. Can this be one of those cases where a device does not work in a 64-bit version of Windows? I doubt it though since I've never had that problem before with any device and I thought that basic things like keyboards would be kind of failsafe. I don't really know how to start debugging this issue. I've tried all the obvious, rebooting, changing the USB port, etc. Are there any generic x64 keyboard drivers you can use? Is there any way to find the manufacturer of the keyboard over USB? There is nothing written on it.

  Read the article

• Opening Word documents from IE LAG Windows 7 IE8

  - by Steve McCall

  Hi, I'm having a lot of trouble opening documents from a network share in word using IE. The documents are located in a network share which is mapped to a virtual directory. The documents are accessed by URLs that link to the virtual directory. There is now a huge lag (sometimes up to a minute or two!) from when clicking on the link to the document opening in word. The 'loading disc' in IE just keeps spinning and nothing happens. Sometimes a pop up box appears with 'opening file - (address)' but it still takes ages. I've tried setting in the registry to open the files directly in ie but to no avail. Anyone have any ideas? Steve

  Read the article

• Why does VNC eat certain characters?

  - by TK Kocheran

  I often use VNC to connect to my desktop upstairs using a laptop downstairs over my home network. I tunnel the VNC connection via SSH. The problem I keep running into is that I'll attempt to type a ! or a : or even a captial A and it will come across the wire as a 1, ;, or a respectively. Is this something I can fix? It's really REALLY annoying while one is programming to have to pop open character map and find a colon and copy/paste it in each time. Running Ubuntu 10.04 upstairs, Linux Mint 10 downstairs.

  Read the article

• Material to use for computer system cover against UV and salty air?

  - by hippietrail

  I live right next to the sea and have a large window quite close to my computer setup which allows a lot of indirect sunlight to enter. I'd like to buy or make a cover for my computer system. From visiting my usual mom & pop computer shop yesterday I got the impression these might not really exist any more. If I make my own I need a material with these qualities: Block or reduce ultraviolet light which can depolymerize plastics (the sun here in Australia is much stronger than in the northern hemisphere). Block salt-laden sea air which can oxidize USB and other connectors. Not cause static electricity when covering or uncovering. Keep dust off of course (-: My setup is a laptop plugged into a wide-screen LCD with a few external drives. So I think I'd want a largish sheet to flop over the whole desk. Are such covers commonly sold these days? What material(s) should I look for which provides the listed attributes?

  Read the article

• Apple Mail Rules application

  - by Steve

  I've got a Mac running Apple Mail and a bberry, both checking the same mail accounts. One account is pop and two accounts are IMAP. The Mac is asleep during the day. While out and about, I'll check my mail on the bberry, read the new messages, and leave them in my inbox. When I come home, I wake up the Mac, and Mail syncs with the server. The filtering rules are not applied to messages that are previously read via bberry. Can I apply rules to 'read' messages? I've tried to select emails in the inbox and then apply rules to them, but that doesn't move the message.

  Read the article

• Making audio CDs en mass - Linux based solutions?

  - by The Journeyman geek

  My mom's sings and gives away cds to people. Invariably it falls to me to have to burn cds for her, and burning 50-100 cds on a single drive is a pain. I DO have a handful of cd burners and a slightly geriatric old PIII 450. This is what i want to be able to do - either point an application at a folder of WAV or MP3s, say how many copies i need on CLI (since then i can SSH into the system and use it headless) feed 2 or more CD burners cds until its done, OR pop in a single CD into a master drive and have its contents duplicated to 2 or more burners. I'd rather have it running on linux, be command line based, and be as little work as possible - almost automatic short of telling it how many copies i want would be ideal. I'm sure i'll have people wondering about legality - My mom sings her own music, and its classical, and older than copyright law, so, that's a non issue. I just want a way to make this chore a little easier, short of telling my mom to do it herself.

  Read the article

• What is a good web interface for remote linux load monitoring?

  - by Jakobud

  I'm looking for some type of remote linux monitoring software that you can view using a web interface. And I'm not just looking for the basic load information. I'm also looking for process information, similar to the info that you get from TOP. Like I'd just like to be able to pop open this webpage to view whats going on with the server at a moments notice. For example, perhaps just a basic PHP page that is on the server that uses basic AJAX to display and refresh results from the TOP command in the page. I was thinking about writing something like this, but I don't want to reinvent the wheel.

  Read the article

• postfix smtps issue

  - by DavidC

  Im currently experiencing the following issue with postfix over ssl (smtps) Apr 7 13:43:55 server88-208-248-147 postfix/smtpd[5777]: connect from xxxxxxxxxxxxxxx[xxx.xxx.xxx.xxx] Apr 7 13:45:09 server88-208-248-147 postfix/smtpd[5777]: lost connection after UNKNOWN from xxxxxxxxxxxxxxx[xxx.xxx.xxx.xxx] Apr 7 13:45:09 server88-208-248-147 postfix/smtpd[5777]: disconnect from xxxxxxxxxxxxxxx[xxx.xxx.xxx.xxx] my main.cf is as follows: smtpd_tls_cert_file = /etc/postfix/smtpd.cert smtpd_tls_key_file = /etc/postfix/smtpd.key smtpd_use_tls = yes smtp_use_tls = yes smtpd_tls_auth_only = no smtpd_tls_CAfile = /etc/postfix/caroot.crt smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_tls_loglevel = 1 when accessing smtp and running start tls i get the following: # telnet xxxxxxxxxxxxxxx 25 Trying xxxxxxxxxxxxxxx... Connected to xxxxxxxxxxxxxxx . Escape character is '^]'. 220 xxxxxxxxxxxxxxx ESMTP Postfix ehlo localhost 250-xxxxxxxxxxxxxxx 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-AUTH PLAIN LOGIN 250-AUTH=PLAIN LOGIN 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN STARTTLS 220 2.0.0 Ready to start TLS please help as i'm lost of places to look now. os is Ubuntu 10.4 and the SSL is a wildcard SSL, imap/pop and apache work flawlessly with the same certificate.

  Read the article

< Previous Page | 61 62 63 64 65 66 67 68 69 70 71 72  | Next Page >