Search Results

Search found 22641 results on 906 pages for 'use case'.

Page 650/906 | < Previous Page | 646 647 648 649 650 651 652 653 654 655 656 657  | Next Page >

• Should I use "Raid 5 + spare" or "Raid 6"?

  - by Trevor Boyd Smith

  What is "Raid 5 + Spare" (excerpt from User Manual, Sect 4.17.2, P.54): RAID5+Spare: RAID 5+Spare is a RAID 5 array in which one disk is used as spare to rebuild the system as soon as a disk fails (Fig. 79). At least four disks are required. If one physical disk fails, the data remains available because it is read from the parity blocks. Data from a failed disk is rebuilt onto the hot spare disk. When a failed disk is replaced, the replacement becomes the new hot spare. No data is lost in the case of a single disk failure, but if a second disk fails before the system can rebuild data to the hot spare, all data in the array will be lost. What is "Raid 6" (excerpt from User Manual, Sect 4.17.2, P.54): RAID6: In RAID 6, data is striped across all disks (minimum of four) and a two parity blocks for each data block (p and q in Fig. 80) is written on the same stripe. If one physical disk fails, the data from the failed disk can be rebuilt onto a replacement disk. This Raid mode can support up to two disk failures with no data loss. RAID 6 provides for faster rebuilding of data from a failed disk. Both "Raid 5 + spare" and "Raid 6" are SO similar ... I can't tell the difference. When would "Raid 5 + Spare" be optimal? And when would "Raid 6" be optimal"? The manual dumbs down the different raid with 5 star ratings. "Raid 5 + Spare" only gets 4 stars but "Raid 6" gets 5 stars. If I were to blindly trust the manual I would conclude that "Raid 6" is always better. Is "Raid 6" always better?

  Read the article

• Good Enough Failover Strategy for DNS / MySQL / Email

  - by IMB

  I've asked and read a lot questions regarding DNS failover but the more I read the more complicated it becomes, some people say it's good enough some say it isn't. No clear answers from what I read. I was wondering if we can set it straight once and for all, at least for the requirements of most websites out there. Right now let's assume the following: We don't need really need load-balancing, what we need is a failover solution. We are running a website based on LAMP on a VPS. We need to make sure that the Web Server, MySQL, Email are always accessible if not 99%. Basically here's my idea and questions about it: Web Server: We need at least one failover server (another VPS on a separate data center). Is DNS Failover via Round Robin good, if not, what's the best? And how do you exactly implement it? How do you make the files you upload/delete on Server A is also on Server B? MySQL: I've only read a brief intro to MySQL replication and I assume that I can replicate Server A to Server B and vice versa on the fly right? So just it case Server A fails and Server B is now running, it will continue to work and replicate to Server A when it becomes available. So in essence Server B is now the primary server, and will later on failover to Server A, should a failure happen again. Email: If we are gonna use DNS Failover, using webmail or relying on emails stored on the server is probably not a good idea right? Since some emails might be on Server A while some might be on Server B? I assume a basic email forwarder to a 3rdparty is good enough (like Gmail for example) to ensure all emails are kept in one place. Here's a basic diagram for a better picture: http://i.stack.imgur.com/KWSIi.png

  Read the article

• Three server processes consume no more than 50% of Dual Core CPU

  - by thor

  I have three processes running on Intel Core 2 Duo CPU. From watching output of 'top' and graphs of CPU load (drawn by MRTG, data collection via SNMP) I can see that CPU load is never more than 50%, and, most of the day, when those processes are busy CPU load has a ceiling at 50 %. I mean, CPU load grows up to 50% in the morning and stays there until late evening. My first thought was that only one core was used at 100% thus giving 50% of both CPUs. But, as there are three processes running and from 'top' I see that both cores are being loaded, so this is not the case. schedtool shows that CPU affinity for those three processes is at default, 0x03, allowing them to use both cores. If I force one process to one core (schedtool -a 0x01), and two others to second (schedtool -a 0x02), cumulative usage grows beyond 50%. Why three processes seem to consume only 50% of two cores? Why forcing them to different CPUs allows usage to grow higher? Any hints? P.S. Processes in question are Counter-Strike servers.

  Read the article

• Adding subnet to a vsphere with single vcenter and esxi host

  - by Ilya Rakhlin

  Let me start of by saying that I do not specialize in networking, I am in the process of adding additional VMs to a testing environment and wanted some recommendations. In this case I am running a single ESXI 5.1 host and a single Vcenter management server. The problem is, I need another range of IP addresses added to the existing setup; hopefully without reconfiguring everything. Currently the esxi host is configured to IP: 192.168.100.200, gateway: 192.168.100.1 and subnet: 255.255.255.0. All of the VMs are running some version of linux with hard coded IP addresses in that range, and using that subnet. The VMs I am about to deploy I want to be on the 192.168.101.X network. Is it possible to add an additional subnet to this existing system that will also communicate with the current subnet? The esxi host has 6 physical NICs but only one connected as it is only a testing system; not sure if that matters. Are there any other ways to accomplish this hopefully without restarting or at least reconfiguring the IP addresses for each VM? Reason: Due to the configuration of the VMs to run the applications that we need I am using a large amount of the current IPs in the potential range (mostly VIPs). I will be setting up a new version of this “environment” while keeping the old one, thus potentially running out of IP addresses.

  Read the article

• mount.nfs: access denied by server while mounting (Kerberos authentication)

  - by Nick

  There's plenty of references to this error on Goggle, and even a question here with the same title, but it seems that "access denied by server while mounting" is a catch-all error. I've tried suggestions that others have used to fix this problem, but they did not work in my case. I'm trying to set-up a Kerberos-based NFS file server with shared homes for a Linux network. I'm using Ubuntu 11.04 Servers and clients. When trying to mount a share using: mount 192.168.1.115:/export/home/ /media/tmp I get: mount.nfs: access denied by server while mounting 192.168.1.115:/export/home/ This is the same if I mount it from a client machine or from the server itself. On the server, in /var/log/syslog I get: Aug 25 06:22:37 nfs mountd[1580]: authenticated mount request from 192.168.1.115:835 for /export/home (/export/home) Aug 25 06:22:37 nfs mountd[1580]: authenticated unmount request from 192.168.1.115:766 for /export/home (/export/home) Which is odd, since it says it's authenticated the request, not denying it. /etc/exports: /export *(rw,fsid=0,crossmnt,insecure,async,no_subtree_check,sec=krb5p:krb5i:krb5) /export/home *(rw,insecure,async,no_subtree_check,sec=krb5p:krb5i:krb5) On client: me@dt1:/$ rpcinfo -p 192.168.1.115 program vers proto port 100000 2 tcp 111 portmapper 100024 1 udp 37320 status 100024 1 tcp 48460 status 100003 2 tcp 2049 nfs 100003 3 tcp 2049 nfs 100003 4 tcp 2049 nfs 100227 2 tcp 2049 100227 3 tcp 2049 100003 2 udp 2049 nfs 100003 3 udp 2049 nfs 100003 4 udp 2049 nfs 100227 2 udp 2049 100227 3 udp 2049 100021 1 udp 58625 nlockmgr 100021 3 udp 58625 nlockmgr 100021 4 udp 58625 nlockmgr 100021 1 tcp 49616 nlockmgr 100021 3 tcp 49616 nlockmgr 100021 4 tcp 49616 nlockmgr 100005 1 udp 45627 mountd 100005 1 tcp 60265 mountd 100005 2 udp 45627 mountd 100005 2 tcp 60265 mountd 100005 3 udp 45627 mountd 100005 3 tcp 60265 mountd Any suggestions I could try?

  Read the article

• Intel Ethernet Bottlenecking Internet?

  - by Donald Darma

  I'm having trouble with my internet speeds. So I just recent build a pc and everything is fine. I installed the Intel drivers and connected to the internet. It connects but I'm only half the speed I should be getting. My normal speed is 20mbps but speedtest.net is only showing 10. It can't be my ISP (which is TWC if anyone is asking) because my other devices like my laptop and my smartphone are showing 20 down. Heres my system: CPU: i5 4430 HSF: Stock cooler Mobo: Gigabyte Z87MX-D3H GPU: x2 MSI R7950-3GD5/OC BE RAM: Crucial Ballistix Tactical Tracer 8GB dual channel PSU: Silencer High Performance Power Supply 750 Watt 80+ (It's a subdivision of OCZ) HDD: Seagate Barracuda 7200RPM 3TB SSD: Samsung 840 Evo 120 GB Case: Corsair Obsidian 350D Edit: I am using the stock adapter that is on the motherboard. I know for a fact that the cable is good because I used it on my laptop and it ran fine. Its a CAT5E cable. I also ran IPERF and its giving me the same results, 10 mbps.

  Read the article

• Large, high performance object or key/value store for HTTP serving on Linux

  - by Tommy

  I have a service that serves images to end users at a very high rate using plain HTTP. The images vary between 4 and 64kbytes, and there are 1.300.000.000 of them in total. The dataset is about 30TiB in size and changes (new objects, updates, deletes) make out less than 1% of the requests. The number of requests pr. second vary from 240 to 9000 and is dispersed pretty much all over, with few objects being especially "hot". As of now, these images are files on a ext3 filesystem distributed read only across a large amount of mid range servers. This poses several problems: Using a fileysystem is very inefficient since the metadata size is large, the inode/dentry cache is volatile on linux and some daemons tend to stat()/readdir() it's way through the directory structure, which in my case becomes very expensive. Updating the dataset is very time consuming and requires remounting between set A and B. The only reasonable handling is operating on the block device for backup, copying, etc. What I would like is a deamon that: speaks HTTP (get, put, delete and perhaps update) stores data it in an efficient structure. The index should remain in memory, and considering the amount of objects, the overhead must be small. The software should be able to handle massive connections with slow (if any) time needed to ramp up. Index should be read in memory at startup. Statistics would be nice, but not mandatory. I have experimented a bit with riak, redis, mongodb, kyoto and varnish with persistent storage, but I haven't had the chance to dig in really deep yet.

  Read the article

• connecting to server with multiple nics in other vlan

  - by Thierry

  I have a windows 2003 server with 3 nics on 3 vlan's (this is in domain 1). nic 1 has a default gateway to my router/firewall (sonicwall). In nic 2 and 3 I have left it empty, because it is advised like that everywhere. Within this domain and VLAN's 1-3 everything works fine. BUT... I have a second domain (domain 2) with a 4th Vlan (all 4 VLAN's connected to the same router/firewall) from which my clients need to access the 2003 server in domain 1 (it's my antivirus management console for both domains). when i ping the server from my vlan4 by it's FQDN, it randomly chooses ip from nic 1, 2 or 3 from my 2003 server. (logically because that server is know in DNS with it's 3 IP-addresses. And that is needed for my VLAN's 1-3) I don't really have a problem with that. BUT, I only get an answer of NIC1 (which sounds logically to me, because it's the only one with a gateway). It is not a router problem, because I'm testing in this phase and ping from vlan4 to any machine in vlan1, 2 or 3 that has 1 nic works just fine. If i add a gateway to nic2 and nic3, I get answer from all 3 nics and this works fine. But I know it's adviced to not do that. Can anyone give me advice in this particular case? Would it really be a problem to add a gateway to nic 2 and 3? They would be pointing to the same router/firewall (only with different ip-address, based on the vlan). Or is there another good solution to fix this problem? Thank's in advance, Thierry.

  Read the article

• Apache2 default vhost in alphabetical order or override with _default_ vhost?

  - by benbradley

  I've got multiple named vhosts on an Apache web server (CentOS 5, Apache 2.2.3). Each vhost has their own config file in /etc/httpd/vhosts.d and these vhost config files are included from the main httpd conf with... Include vhosts.d/*.conf Here's an example of one of the vhost confs... NameVirtualHost *:80 <VirtualHost *:80> ServerName www.domain.biz ServerAlias domain.biz www.domain.biz DocumentRoot /var/www/www.domain.biz <Directory /var/www/www.domain.biz> Options +FollowSymLinks Order Allow,Deny Allow from all </Directory> CustomLog /var/log/httpd/www.domain.biz_access.log combined ErrorLog /var/log/httpd/www.domain.biz_error.log </VirtualHost> Now I when anyone tries to access the server directly by using the public IP address, they get the first vhost specified in the aggregated config (so in my case it's alphabetical order from the vhosts.d directory). Anyone accessing the server directly by IP address, I'd like them to just get an 403 or a 404. I've discovered several ways to set a default/catch-all vhost and some conflicting opinions. I could create a new vhost conf in vhosts.d called 000aaadefault.conf or something but that feels a bit nasty. I could have a <VirtualHost> block in my main httpd.conf before the vhosts.d directory is included. I could just specify a DocumentRoot in my main httpd.conf What about specifying a default vhost in httpd.conf with _default_ http://httpd.apache.org/docs/2.2/vhosts/examples.html#default Would having a <VirtualHost _default_:*> block in my httpd.conf before I Include vhosts.d/*.conf be the best way for a catch-all?

  Read the article

• How to prevent asymmetric routing with multiple eBGP routers?

  - by Andy Shinn

  I have 2 routers announcing a /22 subnet to different providers (one providers connects to each of the 2 routers). I have split the /22 in two /23 to announce one /23 on each of the routers plus the /22 (the providers will take the more specific route). This allows me to fail over and keep traffic inside the /23 in and out the same provider. What are other ways in which I could announce just the /22 with both routers and have packets from servers on the network behind the routers go back out the same router in which they came in from? EDIT: The main problem I come across, which end users and clients complain about the most, is that the least hop route is sometimes not the "optimal" route. In my case, I know that Provider B may have better latency to X nation. But when packets come in from provider B, they may go out Provider A or provider B. The reverse is also true. If I send a packet to X nation out provider A, even though it may have more hops back, the packet will likely come in from Provider B (which may have higher latency, packet loss, etc. to this nation)

  Read the article

• Ubuntu 12.10 64bit host reboots when trying to install any guest system using VirtualBox

  - by gts123

  I am having a really nasty problem with VirtualBox as everytime I try to install any guest OS(using ISO file as CD for installation media), the installation starts normally but as soon as it is about to start either installing to virtual hard drive or loading(e.g. as LiveFS) it causes the host system to reboot abruptly. Config is as below: Host system: Ubuntu 12.10 64bit - Intel® Core i7-2640M CPU @ 2.80GHz × 4 Virtualbox version: 4.1.18_Ubuntu r78361 Guest OS systems tried: 32bit version of FreeBSD 9, Debian 6, Tails 0.14 VM setup Tried to have the minimal setup necessary just in case it would avoid for each system to make sure I'd avoid conflicts, but to no avail. I've tried different values and combinations of the below but the problem still persists: Shared Clipboard: Disabled Show in fullscreen/seamless: Disabled Remember runtime changes: DIsabled Base Memory: 2048 MB Chipset: PIIX3 IO APIC: Disabled EFI: Disabled Absolute Pointing device: Disabled Processor(s): 1 CPU PAE/NX: Disabled VT-x/AMD-V: Disabled Video Memory: 12 MB 3d/2d acceleration: Disabled Storage IDE COntroller: PIIX3 (same as chipset instead of PIIX4) Use host I/O cache: No Audio: disabled Network adapter: NAT USB controller: disabled No shared folder Also another sideeffect of the reboot is that it appears that it does not log any information in the error log files; not making things any easier. Please help.

  Read the article

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  Hi All, I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: http://superuser.com/questions/12955/how-do-i-remove-the-option-to-eject-sata-drives-from-the-windows-7-tray-icon

  Read the article

• Windows 7 Startup fails after installation

  - by Nadav S.

  I have installed Windows 7 Ultimate a week ago. Yesterday I've noticed that the SP1 update is available. After installation of SP1 the computer failed to startup, and had shown a black screen. I couldn't even go to safe mode and F8 didn't help. After some fixing attempts including system restore, startup repair, bootmgr & BCD rebuilding from CMD, I have decided to reinstall Windows (after all, it's only a week old) After the successful installation, I have decided to first install all available updates before I continue. So after the updates download & installation, the computer rebooted. And now I didn't see the black screen again - but in the "Starting Windows..." screen the logo didn't appear and the system didn't startup. Here I could go to safe mode selection window, but it didn't work either ("Loading Windows Files" but nothing). I've also tried: I thought that the CD was corrupted, so I've used a fresh new disk of Windows, tried x86 & x64 versions, the same symptoms, no change. Resetted the BIOS to default, no change. Memory diagnostic HDD diagnostic Restarted Windows WITHOUT INSTALLING UPDATES, but it had the same symptom, so maybe Windows Update is not the case?! I've tried installing it so many times - that I am simply stuck - I can't "reinstall Windows, because it is corrupted...". Maybe the HDD is corrupted? I've also checked it and didn't find a problem.

  Read the article

• Access NFS share from cygwin?

  - by Jason Voegele

  We have a Windows 2003 Server on which we have installed Microsoft's Services for UNIX, and we have mounted a few NFS shares that contain shared resources that we need to access from this box. When I log in to this server with remote desktop, I am able to browse the contents of the NFS shares and everything works fine. However, one use case that we have is that we need to access this server using SSH, and still be able to access the NFS shares. We are running the Cygwin SSH daemon to provide SSH access to the server, but for some reason when we log in to the Windows 2003 server using SSH we can no longer access the NFS shares. To demonstrate, here is the output of the 'mount' command, first from a Cygwin shell when logged in with remote desktop: $ mount C:/cygwin/bin on /usr/bin type ntfs (binary,auto) C:/cygwin/lib on /usr/lib type ntfs (binary,auto) C:/cygwin on / type ntfs (binary,auto) C: on /cygdrive/c type ntfs (binary,posix=0,user,noumount,auto) O: on /cygdrive/o type nfs (binary,posix=0,user,noumount,auto) P: on /cygdrive/p type nfs (binary,posix=0,user,noumount,auto) Z: on /cygdrive/z type nfs (binary,posix=0,user,noumount,auto) And now, the same 'mount' command when logged in with SSH: $ mount C:/cygwin/bin on /usr/bin type ntfs (binary,auto) C:/cygwin/lib on /usr/lib type ntfs (binary,auto) C:/cygwin on / type ntfs (binary,auto) C: on /cygdrive/c type ntfs (binary,posix=0,user,noumount,auto) Notice the missing O: P: and Z: NFS shares in the latter. Can anyone tell me why I am unable to see these NFS shares when logged in with SSH? Thanks!

  Read the article

• Mangling traffic from a Mikrotik Router

  - by TiernanO

  I have a MikroTik powered Router in the house with a couple of internet connections (2 200/10Mb Cable modems and a 100/20Mb VDSL Line). I am using Mangle rules to set routing marks and NAT rules to do some load balancing, and everything seems to be going grand... But it only works for traffic from outside the router... Let me explain: I have 4 GigE ports on the machine, WAN1,2 and 3, and a LAN port named LAN1. All traffic from LAN1 is getting mangled (as it should be) but traffic from the load router itself (proxy traffic, IPv6 tunnels, VPN connections) are not being mangled. They get the first route to 0.0.0.0/0, which in my case is WAN2, and stick with it. So, how do I get traffic from the local router to be mangled? Originally it was proxy traffic that caused the problem, but now with IPv6 and VPN, they are more important to be mangled... last time i enabled IPv6 traffic, all traffic only went though WAN2, and the rest where unused... Any ideas?

  Read the article

• Limiting bandwith on an Windows 7 machine

  - by Mihai Damian

  I need to limit the bandwidth on my Windows 7 x64 machine. In the past (on XP) I've been able to use NetLimiter for similar tasks. However for some reason I can't get it to work anymore. For lower limits the bandwidth tests are able to exceed the limit by 10-50%; higher limits seem to be ignored completely and the bandwidth tests report download speeds of over 10 times the speed I set. I'm using speedtest.net and some similar service from my ISP for these tests. Anyway, I don't necessarily need a program as complex as NetLimiter since I only need to throttle my machine's bandwidth, not a specific program's. In case you are wondering why in the world I'd want to cripple my Internet speed, there is a funny story behind this. Long story short, my modem gets random disconnects. Tech support comes in, says my Internet speed is abnormally high and I must be using some tools to somehow make it go faster than it's supposed to and this messes up my modem. I check the connection with another computer and it seems that my PC is the only one in my network that gets abnormal speeds. I reinstall my OS, speed looks normal at first, after I install the batch of 50 or so updates, it goes back to abnormally high speeds and the disconnect problems are not solved. Now I don't have a clue if the explanation the tech team gave me was just a strategy to lay the blame on someone else, but I was trying to give them the benefit of the doubt and see what happens if I really reduce my speed to their specification. Any help appreciated.

  Read the article

• How to simulate Apache [END] flag on a redirect?

  - by Javier Méndez

  For business-specific reasons I created the following rewrite rule for Apache 2.2.22 (mod_rewrite): RewriteRule /site/(\d+)/([^/]+)\.html /site/$2/$1 [R=301,L] Which if given an URL like: http://www.mydomain.com/site/0999/document.html Is translated to: http://www.mydomain.com/site/document/0999.html That's the expected scenario. However, there are documents which name are only numbers. So consider the following case: http://www.mydomain.com/site/0055/0666.html Gets translated to: http://www.mydomain.com/site/0666/0055.html Which also matches my rewrite rule pattern, so I end up with "The web page resulted in too many redirects" errors from browsers. I have researched for a long time, and haven't found "good" solutions. Things I tried: Use the [END] flag. Unfortunately is not available on my Apache version nor it works with redirects. Use %{ENV:REDIRECT_STATUS} on a RewriteCond clause to end the rewrite process (L). For some reason %{ENV:REDIRECT_STATUS} is empty all the times I tried. Add a response header with the Header clause if my rule matches and then check for that header (see: here for details). Seems that a) REDIRECT_addHeader is empty b) headers are can't be set on the 301 response explicitly. There is another alternative. I could set a query parameter to the redirect URL which indicates it comes from a redirect, but I don't like that solution as it seems to hacky. Is there a way to do exactly what the [END] flag does but in older Apache versions? Such as mine 2.2.22. Thanks!

  Read the article

• Openbsd init script for ssh VPN tunnel

  - by manthis

  I have a server hosting SSH tunnels and Openbsd 4.5 clients connecting to it. Things work just fine but I am in the need of automating the connection from the client to the server. So that if the client is accidentally rebooted, then the connection initiates unattended. So it should be as straight forward as to include the ssh connection in an init script. However I have miserably failed to do so by including it to /etc/rc.local, which is the file I usually do this sort of things in. Right now I am using autossh to also restart the connection if necessary and the script that I put on /etc/rc.local follows: #!/bin/sh # # Example script to start up tunnel with autossh. # # This script will tunnel 2200 from the remote host # to 22 on the local host. On remote host do: # ssh -p 2200 localhost # # $Id: autossh.host,v 1.6 2004/01/24 05:53:09 harding Exp $ # ID=root HOST=example.com #AUTOSSH_POLL=600 #AUTOSSH_PORT=20000 #AUTOSSH_GATETIME=30 #AUTOSSH_LOGFILE=$HOST.log #AUTOSSH_DEBUG=yes #AUTOSSH_PATH=/usr/local/bin/ssh export AUTOSSH_POLL AUTOSSH_LOGFILE AUTOSSH_DEBUG AUTOSSH_PATH AUTOSSH_GATETIME AUTOSSH_PORT autossh -2 -f -M 20000 ${ID}@${HOST} The script detaches just fine when run manually so I just include it on /etc/rc.local as echo -n 'starting local daemons:' if [ -x /usr/local/sbin/autossh.sh ]; then echo -n 'ssh tunnel' /usr/local/sbin/autossh.sh fi echo '.' I have also tried calling it from /etc/hostname.tun0 in case there may be issues with /etc/rc.local not being called at the right time when network connections are ready, so I would use: inet 10.254.254.2 255.255.255.252 10.254.254.1 !/usr/local/sbin/autossh.sh Your input is highly appreciated.

  Read the article

• Sending e-mail on behalf of our customer(s), with Postfix

  - by NathanE

  We send e-mail on behalf of our customers, via our own SMTP services. It's always been a problem for us because usually our "spoofing" of their source address results in the mails being caught in spam traps. This hasn't been a problem in the past due to the small volume and low importance of these mails that we sent. However this requirement has recently changed and we need to fix this issue. We realise that fundamentally our application is sending e-mail incorrectly, as per this post: Send email on behalf of clients However, we would like to resolve the problem at the SMTP server level. We have deployed a server running Postfix. Is it possible to have Postfix automatically adjust the mail headers so that we get this "Sent on behalf of" behaviour? I figure it should just be a case of Postfix noticing that the FROM address is the spoofed (i.e. a domain that is not mentioned in its config anywhere) and therefore inject/replace the appropriate headers to get the desired effect. Thanks.

  Read the article

• MX records set up

  - by andrei.troll

  I just want to know how other people set up their MX-entries for mail accounts used with google apps. I work at a local web-hosting firm and we get a lot of tickets from clients who want to set up these settings. I just set them up something like: example.com. 14400 IN MX 10 ALT1.ASPMX.L.GOOGLE.COM. example.com. 14400 IN MX 10 ASPMX4.GOOGLEMAIL.COM. example.com. 14400 IN MX 15 ASPMX5.GOOGLEMAIL.COM. example.com. 14400 IN MX 15 ASPMX2.GOOGLEMAIL.COM. example.com. 14400 IN MX 30 ASPMX3.GOOGLEMAIL.COM. I see another firm (rival one) who sets up way more MX-records ? Roughly, around 10-15 entries. Am I doing something wrong ? More is better in this case ? Is there a secret that I'm not on too ?

  Read the article

• Active Directory: how to be SURE users can change their own passwords?

  - by Latro

  Working on some project where a tool we have has to authenticate against AD connecting via LDAPS and perform password changes if required or requested. IN THEORY, the tool does that, and we have seen it work in other projects. IN PRACTICE, against this particular directory, it fails. Been driving me crazy. The particulars of the situation: Windows 2003 AD Defined a "technical user" for the LDAP connection with rights to change users passwords When password change is required - in this case, because pwdLastSet is 0 - the tool uses the technical account to go, bind to the controller and change the user password. If password change is not required but the user request it, then the bind is done with the user account. That last condition is the one that doesnt work. With the technical user the password change is possible, but with the user itself, it isnt. We get an error like this: LDAP access failed: javax.naming.directory.InvalidAttributeValueException: [LDAP: error code 19 - 0000052D: AtrErr: DSID-03190F00, #1: 0: 0000052D: DSID-03190F00, problem 1005 (CONSTRAINT_ATT_TYPE), data 0, Att 9005a (unicodePwd) no idea what DSID-03190F00 means cause it doesnt seem to be anywhere in google :-/ Been looking at several MS documentation pages and frankly, I'm not understanding one bit of it. There is some "control access right" called User-Change-Password that may, or may not, control what objects have the right to change their own password, which may, or may not, have to do with ACE and ACLs... There is GPO. There is maybe the password policy but it is only set to ask for passwords of 6 chars or more... Can anybody explain to me in easy-to-check steps how can I go and tell the AD admin guy (who is as lost as me) what to do to ensure that users in the AD directory (objectClass top,person,organizationalPerson and user) are able to change their own passwords by themselves? Thanks in advance

  Read the article

• MAMP Pro mysqld won't start on os x lion

  - by Mike

  getting a Start MySQL Failed error in the GUI.. when i attempt to start mysqld from the CLI i get the following error: ? /Applications/MAMP/Library/bin/mysqld 120623 23:12:47 [Warning] Setting lower_case_table_names=2 because file system for /Applications/MAMP/db/mysql/ is case insensitive 120623 23:12:47 [Note] Plugin 'FEDERATED' is disabled. 120623 23:12:47 InnoDB: The InnoDB memory heap is disabled 120623 23:12:47 InnoDB: Mutexes and rw_locks use GCC atomic builtins 120623 23:12:47 InnoDB: Compressed tables use zlib 1.2.3 120623 23:12:47 InnoDB: Initializing buffer pool, size = 128.0M 120623 23:12:47 InnoDB: Completed initialization of buffer pool 120623 23:12:47 InnoDB: highest supported file format is Barracuda. 120623 23:12:47 InnoDB: Waiting for the background threads to start 120623 23:12:48 InnoDB: 1.1.5 started; log sequence number 1595675 120623 23:12:48 [ERROR] /Applications/MAMP/Library/bin/mysqld: unknown option '--skip-locking' 120623 23:12:48 [ERROR] Aborting 120623 23:12:48 InnoDB: Starting shutdown... 120623 23:12:49 InnoDB: Shutdown completed; log sequence number 1595675 120623 23:12:49 [Note] /Applications/MAMP/Library/bin/mysqld: Shutdown complete i have deleted the mysql.pid file located at /application/mamp/tmp/mysql/mysql.pid and i still get the error above. I can't find where MAMP has set --skip-locking set, my.cnf doesnt have it anywhere. Activity monitor gives me a mysqld process running by me, and everytime i KILL the process both via Activity Monitor and via kill =9 pid it starts right back up.. Sampling the process points back to the MAMP mysqld.. wtf?! About to throw MAMP out the window and boot up a VM of CentOS =)

  Read the article

• Printer Naming Conventions

  - by John

  I am working on building a new AD print server and have been pondering the idea of renaming the printers. Right now we have a mix of names that varies between a mashup of some that reference location, some that reference functional area, and some that are rather generic. Some examples include the following: Dell 5210 - Building Name HP 4350 - Functional Area Dell Color 3100 - Location and Building Number HP 6500 - Mailroom I was curious what other people used to name their printers with. What conventions do you use and how to design a method that will be able to be used for a while without needing to rename them all again. Also, the naming methodology needs to be understandable for regular computing users so that they can relatively easily find the printer that they need. I was looking at some ideas from here, but I was not sure how practical some of them are. Any help that you can provide is appreciated. Note: I have reviewed many of the postings on here in relation to server naming conventions and found that they were not specific enough for the use case I present above.

  Read the article

• How to reproduce the behavior of Mac OS X's dead keys on Windows 7?

  - by Pascal Qyy

  I'm French, but I've chosen to take a QWERTY keyboard for my MacBook Pro for many reasons: first of all, the AZERTY keyboard is not at all ergonomic because it has no numeric keypad, and I must use MAJ or CAPS LOCK to access to the numeric keys ; secondly, I've bought this mac for development ; and chars {, }, etc., are not directly accessible on the Apple AZERTY keyboard the last thing is that: the diacritics are VERY easy to produce on an Apple keyboard with Mac OS X : ? + c for a ç, for example, and many dead keys easy to use (e.g. ? + e, then e give you an é. So, I have no difficulties to write in my native language with this keyboard under Mac OS X. BUT, when I boot on Windows 7's Boot Camp partition, or when I use applications from it through VMware Unity, it is no longer the same comfort! Without numeric keypad, it's impossible to use it for produce specials characters (e.g.: Alt + 0231 for the ç) I've tried many solutions, like auto replacement in Microsoft Office (e.g.: ,,c being replaced by ç), but for all my diacritics, I must type a space, then a back space before the replacement work. I've also tried third party software, as Texter, but it is very buggy and don't work properly (or don't work at all) in many case! So, is there a solution somewhere, to have this Mac OS X's nice and comfortable way of producing diacritics for Windows 7? Thank in advance for your help and your time!

  Read the article

• How can I create a simple Exchange 2010 backup solution?

  - by bduncanj

  I'm sure this question's been asked a dozen times in one form or another, however after much searching, there doesn't appear to be an obvious simple recovery solution for a single Exchange box. We're using Exchange 2010 on a single server, the server hosts the AD and nothing else on the network uses the AD. The intent is to run this server as you would an externally hosted Exchange server - access only via HTTP (RPC mode or OWA) - all other ports blocked. I've a daily backup running, using Windows Server 2008 volume shadow service to backup the Exchange data to an external hard disk. My question is, how do I perform a bare metal recovery of this server? 1) Do I need to be explicitly including the active directory information in this nightly backup, or will it be there by virtue of the fact that this system is the primary AD server and the Windows backup service knows this? 2) I understand I can re-install Server 2008 onto my new hardware (in the case of hardware failure) and then run Exchange 2010 setup.exe with a /recover argument, referencing the backup volume. 3) It is acceptable to have some downtime during this recovery process. But is there anything else I should be aware of? Thanks! Duncan

  Read the article

< Previous Page | 646 647 648 649 650 651 652 653 654 655 656 657  | Next Page >