Search Results

Search found 14837 results on 594 pages for 'duplicate ip'.

Page 66/594 | < Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >

• switch OFF syn cookies

  - by Nick

  We have several servers they have public IP's, but work together (one is with Load Balancer, orther with Apache Web server, other with MySQL and so on. Most of the ports are fire-walled, so only "local" servers can be connect there. However ALL servers have some ports that must be publicly open. We have SYN Cookies enabled and from time to time we got: possible SYN flooding on port 8080. Sending cookies. Port 8080 is not public. How we can switch OFF SYN Cookies for some ports (e.g. 8080, 3306 etc) or from some sources (e.g. our servers), but in same time SYN Cookies to be switched ON for all other ports, e.g. port 80. We found this similar problem, except our servers are with public IP's: SYN cookies on internal machines

  Read the article

• What router hardware or software should be used when multiple public IPs are routed into the same LAN?

  - by lcbrevard

  I am looking for recommendations to replace a set of consumer grade (Linksys, Netgear, Belkin) routers with something that can handle more traffic while routing more than one static public IP into the same LAN address space. We have a block of static public IPs, 5 usable, with Comcast Business. Currently four of them are in use for: General office access Web server Mail and DNS servers Download and backup web server for separate business All systems (a mixture of physical and virtual) are in the same LAN address space (10.x.y.0/24) to enable easy access between them inside the office. There are 30 or more systems in use depending on which virtual machines are currently active. We have a mixture of Windows, Linux, FreeBSD, and Solaris. Currently a separate consumer grade router is used for each of the four static addresses, with its WAN address set to the specific static address and a different gateway address for each: uses 10.x.y.1 - various ports are forwarded to various LAN IPs on systems with gateway 10.x.y.1 uses 10.x.y.254 - port 80 is forwarded to a server with gateway 10.x.y.254 uses 10.x.y.253 - ports for mail and dns are forwarded to a server with gateway 10.x.y.253 uses 10.x.y.252 - ports as needed are forwarded to server with gateway 10.x.y.252 Only router 1. is allowed to serve DHCP and address reservation based on the MAC is used for most of the internal "server" IP addresses so they are at fixed values. [Some are set static due to limitations in the address reservation capabilities of router 1.] And, yes, this really does work! But... I am looking for: better DHCP with more capable address reservation higher capacity so I don't have to periodically power cycle the routers One obvious improvement would be to have a real DHCP server and not use a consumer grade router for that purpose. I am torn between buying a "professional" router such as Cisco or Juniper or Sonic Wall verus learning to configure some spare hardware to perform this function. The price goes up extremely rapidly with capabilities for commercial routers! Worse, some routers require licensing based on the number of clients - a disaster in our environment with so many virtual machines. Sorry for such a long posting but I am getting tired of having to power cycle routers and deal with shifting IP addresses afterwards!

  Read the article

• What are the methods of separating network spaces in a LAN?

  - by dash17291

  Please detail me the methods. My thoughts: put the servers in separate (sub)networks the servers are forced to go through the firewall but no NAT is required assign more IP addresses to the internal interface of the server choosing gateway addresses from the clients and servers IP address ranges split DNS Netfilter/{iptables, ipset} could be heavily involved, I'm talking about Linux servers. See for example: Destination NAT Onto the Same Network from internal clients Please do not explain what is NAT or DNS. This is a theoretical question, but my poor English knowledge prevent me to describe it in a fancy fashion.

  Read the article

• Isolated Network Set-Up

  - by Isaac Kleinman

  I am looking to set up a small network for a client which would be isolated from his primary network. (I'm hoping to set-up the additional network as VMs on the primary network.) I've instructed the client to request a bunch of static ip addresses from his ISP, but I'm not sure how to proceed with setting this up. What hardware will I need and how do I go about the configuration? Heavy security is not my concern. All that's really required is that web requests from the two networks be presented to the outside world with different ip addresses.

  Read the article

• Request to server x Reply from server y

  - by klaasio

  I need some advice from you guys: I'm dealing with a custom loadbalancer/software for which we will use 2 main servers and about 8 slave servers. In short: User sends request to main server, main server will receive and handle the requests, sends a request to a slave server and slave server should send data DIRECTLY to the "user". User - Main server Main server - Slave server Slave server - User The reason for which data should be send directly to the user and not through the main server is because of bandwidth and low budget. Now I have the following idea's: -IPinIP, but that is not possible in Layer7 (so far i know there some expensive routers for that) -IP Spoof, using C/C++ we will make it look like the reply came from main server. But I was thinking, perhaps the reply "slave server - User" could just come from a different IP without causing issues in the firewall from the user or his anti-virus. I don't know so well about "home" firewalls/routers and/or anti-virus software. I guess the user machine wouldn't handle it well?

  Read the article

• Steps to Investigate Cause of Web.Config Duplicate Section

  - by pauly

  Symptoms In IIS Dot Net 2.0 Integrated app pool: double clicking to view any web.config section results in a the following error dialog. "There was an error while performing this operation.... Fielname... web.config... Error: There is a duplicate..." Browsing to the URL displays: "Http 500.19" internal server error.. There is a duplicate... 'system.web.extensions/scripting/scriptResourceHandler' section defined...." Running the app from VS 2008 an "Unable to start debugging on the web server..." dialog is displayed. Things Tried Looked at other application directories on same IIS server. No problem view web.config contents or serving up the app. Removed and re-added the application in IIS. Checked out a new version of the source code. Reverted to prior versions of the web.config file. Looked for web.config files that might have duplicate sections in: Inetpub root. "C:\Windows\Microsoft.NET\Framework\v2.0.50727\CONFIG\machine.config" The "Views" subfolder of the ASP.Net MVC app. Checked out source code to another dev machine. Setup IIS 7 app folder. No problem with Web.config. Question If the reason for this error is another web.config file where else should I look? Are there other reasons for these symptoms?

  Read the article

• Delete Duplicate records from large csv file C# .Net

  - by Sandhurst

  I have created a solution which read a large csv file currently 20-30 mb in size, I have tried to delete the duplicate rows based on certain column values that the user chooses at run time using the usual technique of finding duplicate rows but its so slow that it seems the program is not working at all. What other technique can be applied to remove duplicate records from a csv file Here's the code, definitely I am doing something wrong DataTable dtCSV = ReadCsv(file, columns); //columns is a list of string List column DataTable dt=RemoveDuplicateRecords(dtCSV, columns); private DataTable RemoveDuplicateRecords(DataTable dtCSV, List<string> columns) { DataView dv = dtCSV.DefaultView; string RowFilter=string.Empty; if(dt==null) dt = dv.ToTable().Clone(); DataRow row = dtCSV.Rows[0]; foreach (DataRow row in dtCSV.Rows) { try { RowFilter = string.Empty; foreach (string column in columns) { string col = column; RowFilter += "[" + col + "]" + "='" + row[col].ToString().Replace("'","''") + "' and "; } RowFilter = RowFilter.Substring(0, RowFilter.Length - 4); dv.RowFilter = RowFilter; DataRow dr = dt.NewRow(); bool result = RowExists(dt, RowFilter); if (!result) { dr.ItemArray = dv.ToTable().Rows[0].ItemArray; dt.Rows.Add(dr); } } catch (Exception ex) { } } return dt; }

  Read the article

• MySQL Normalization stored procedure performance

  - by srkiNZ84

  Hi, I've written a stored procedure in MySQL to take values currently in a table and to "Normalize" them. This means that for each value passed to the stored procedure, it checks whether the value is already in the table. If it is, then it stores the id of that row in a variable. If the value is not in the table, it stores the newly inserted value's id. The stored procedure then takes the id's and inserts them into a table which is equivalent to the original de-normailized table, but this table is fully normalized and consists of mainly foreign keys. My problem with this design is that the stored procedure takes approximately 10ms or so to return, which is too long when you're trying to work through some 10million records. My suspicion is that the performance is to do with the way in which I'm doing the inserts. i.e. INSERT INTO TableA (first_value) VALUES (argument_from_sp) ON DUPLICATE KEY UPDATE id=LAST_INSERT_ID(id); SET @TableAId = LAST_INSERT_ID(); The "ON DUPLICATE KEY UPDATE" is a bit of a hack, due to the fact that on a duplicate key I don't want to update anything but rather just return the id value of the row. If you miss this step though, the LAST_INSERT_ID() function returns the wrong value when you're trying to run the "SET ..." statement. Does anyone know of a better way to do this in MySQL? Thank you

  Read the article

• Remove redundant SQL code

  - by Dave Jarvis

  Code The following code calculates the slope and intercept for a linear regression against a slathering of data. It then applies the equation y = mx + b against the same result set to calculate the value of the regression line for each row. Can the two separate sub-selects be joined so that the data and its slope/intercept are calculated without executing the data gathering part of the query twice? SELECT AVG(D.AMOUNT) as AMOUNT, Y.YEAR * ymxb.SLOPE + ymxb.INTERCEPT as REGRESSION_LINE, Y.YEAR as YEAR, MAKEDATE(Y.YEAR,1) as AMOUNT_DATE FROM CITY C, STATION S, YEAR_REF Y, MONTH_REF M, DAILY D, (SELECT ((avg(t.AMOUNT * t.YEAR)) - avg(t.AMOUNT) * avg(t.YEAR)) / (stddev( t.AMOUNT ) * stddev( t.YEAR )) as CORRELATION, ((sum(t.YEAR) * sum(t.AMOUNT)) - (count(1) * sum(t.YEAR * t.AMOUNT))) / (power(sum(t.YEAR), 2) - count(1) * sum(power(t.YEAR, 2))) as SLOPE, ((sum( t.YEAR ) * sum( t.YEAR * t.AMOUNT )) - (sum( t.AMOUNT ) * sum(power(t.YEAR, 2)))) / (power(sum(t.YEAR), 2) - count(1) * sum(power(t.YEAR, 2))) as INTERCEPT FROM ( SELECT AVG(D.AMOUNT) as AMOUNT, Y.YEAR as YEAR, MAKEDATE(Y.YEAR,1) as AMOUNT_DATE FROM CITY C, STATION S, YEAR_REF Y, MONTH_REF M, DAILY D WHERE $X{ IN, C.ID, CityCode } AND SQRT( POW( C.LATITUDE - S.LATITUDE, 2 ) + POW( C.LONGITUDE - S.LONGITUDE, 2 ) ) < $P{Radius} AND S.STATION_DISTRICT_ID = Y.STATION_DISTRICT_ID AND Y.YEAR BETWEEN 1900 AND 2009 AND M.YEAR_REF_ID = Y.ID AND M.CATEGORY_ID = $P{CategoryCode} AND M.ID = D.MONTH_REF_ID AND D.DAILY_FLAG_ID <> 'M' GROUP BY Y.YEAR ) t ) ymxb WHERE $X{ IN, C.ID, CityCode } AND SQRT( POW( C.LATITUDE - S.LATITUDE, 2 ) + POW( C.LONGITUDE - S.LONGITUDE, 2 ) ) < $P{Radius} AND S.STATION_DISTRICT_ID = Y.STATION_DISTRICT_ID AND Y.YEAR BETWEEN 1900 AND 2009 AND M.YEAR_REF_ID = Y.ID AND M.CATEGORY_ID = $P{CategoryCode} AND M.ID = D.MONTH_REF_ID AND D.DAILY_FLAG_ID <> 'M' GROUP BY Y.YEAR Question How do I execute the duplicate bits only once per query, instead of twice? The duplicate bit is the WHERE clause: $X{ IN, C.ID, CityCode } AND SQRT( POW( C.LATITUDE - S.LATITUDE, 2 ) + POW( C.LONGITUDE - S.LONGITUDE, 2 ) ) < $P{Radius} AND S.STATION_DISTRICT_ID = Y.STATION_DISTRICT_ID AND Y.YEAR BETWEEN 1900 AND 2009 AND M.YEAR_REF_ID = Y.ID AND M.CATEGORY_ID = $P{CategoryCode} AND M.ID = D.MONTH_REF_ID AND D.DAILY_FLAG_ID <> 'M' Related http://stackoverflow.com/questions/1595659/how-to-eliminate-duplicate-calculation-in-sql Thank you!

  Read the article

• Duplicate Symbol Linker Error (C++ help)

  - by Vash265

  Hi. I'm learning some CSP (constraint satisfaction) theory stuff right now, and am using this library to parse XML files. I'm using Xcode as an IDE. My program compiles fine, but when it goes to link the files, I get a duplicate symbol error with the XMLParser_libxml2.hh file. My files are separated as such: A class header file that includes the XMLParser file above A class implementation file that include the class header file A main file that includes the class header file The duplicate symbol is occurring in main.o and classfile.o, but as far as I can tell, I'm not actually adding that .hh file twice. Full error: ld: duplicate symbol bool CSPXMLParser::UTF8String::to<std::basic_string<char, std::char_traits<char>, std::allocator<char> > >(std::basic_string<char, std::char_traits<char>, std::allocator<char> >&) constin /Users/vash265/CSP/Untitled/build/Untitled.build/Debug/Untitled.build/Objects-normal/x86_64/dStructFill.o and /Users/vash265/CSP/Untitled/build/Untitled.build/Debug/Untitled.build/Objects-normal/x86_64/main.o Copying the implementation of the class into the main file and taking the class implementation file out of the compilation target alleviates the error, but it's a disorganized mess this way, and I'll be adding more classes very soon (and it would be nice to have them in separate files). As I've come to understand it, this is caused by the file (XMLParser_libxml2.hh) having both the class and function definition and implementation in one file (and it seems as though this might have been necessary due to the use of templates in that 'header' file). Any ideas on how to get around sticking all my class files in my main.cpp? (I've tried ifdefs, they don't work).

  Read the article

• Entityframework duplicate record on second insert

  - by Delysid

  I am building an application for recipe/meal planning, and i have come across a problem i cant seem to figure out. i have a table for units of measure, where i keep the used units in, i only want unique units in here (for grocery list calculation and so forth) but if i use a unit from the table on a recipe, the first time it is okay, nothing is inserted in units of measure, but the second time i get a "duplicate". i suspect it has something to do with entitykey, because the primary key is identity column on the sql server (2008 r2) for some reason it works to change the objectstate on some objects (courses, see code) and that does not generate a duplicate, but that does not work on the unit of measure my insert methods looks like this : public recipe Create(recipe recipe) { using (RecipeDataContext ctx = new RecipeDataContext()) { foreach (recipe_ingredient rec_ing in recipe.recipe_ingredient) { if (rec_ing.ingredient.ingredient_id == 0) { ingredient ing = (from _ing in ctx.ingredients where _ing.name == rec_ing.ingredient.name select _ing).FirstOrDefault(); if (ing != null) { rec_ing.ingredient_id = ing.ingredient_id; rec_ing.ingredient = null; } } if (rec_ing.unit_of_measure.unit_of_measure_id == 0) { unit_of_measure _uom = (from dbUom in ctx.unit_of_measure where dbUom.unit == rec_ing.unit_of_measure.unit select dbUom).FirstOrDefault(); if (_uom != null) { rec_ing.unit_of_measure_id = _uom.unit_of_measure_id; rec_ing.unit_of_measure = null; } } ctx.Recipes.AddObject(recipe); //for some reason it works to change object state of this, and not generate a duplicate ctx.ObjectStateManager.ChangeObjectState(recipe.courses[0], EntityState.Unchanged); } ctx.SaveChanges(); } return recipe; } My datamodel looks like this : http://i.imgur.com/NMwZv.png

  Read the article

• how does openvpn decide which interface to get IP addrs from

  - by bkrupa

  Using ubuntu 10.04 on both ends. We have a client and server machine on the SAME network attempting to make a vpn connection. We use the config files from here and made minimal changes. The server and client start and seem to connect without any trouble. The server looks like: Wed Feb 23 22:13:22 2011 MULTI: multi_create_instance called Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Re-using SSL/TLS context Wed Feb 23 22:13:22 2011 192.168.1.55:47166 LZO compression initialized Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Control Channel MTU parms [ L:1574 D:138 EF:38 EB:0 ET:0 EL:0 ] Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Data Channel MTU parms [ L:1574 D:1450 EF:42 EB:135 ET:32 EL:0 AF:3/1 ] Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Local Options hash (VER=V4): 'f7df56b8' Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Expected Remote Options hash (VER=V4): 'd79ca330' Wed Feb 23 22:13:22 2011 192.168.1.55:47166 TLS: Initial packet from 192.168.1.55:47166, sid=69112e42 5458135b *...* Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Feb 23 22:13:22 2011 192.168.1.55:47166 [client1] Peer Connection Initiated with 192.168.1.55:47166 On the client side the connection looks like: Wed Feb 23 22:20:07 2011 [server] Peer Connection Initiated with [AF_INET]192.168.1.41:1194 Wed Feb 23 22:20:10 2011 SENT CONTROL [server]: 'PUSH_REQUEST' (status=1) Wed Feb 23 22:20:10 2011 PUSH: Received control message: 'PUSH_REPLY,route-gateway 10.8.0.4,ping 10,ping-restart 120,ifconfig 10.8.0.50 255.255.255.0' ... Wed Feb 23 22:20:10 2011 /sbin/ifconfig tap0 10.8.0.50 netmask 255.255.255.0 mtu 1500 broadcast 10.8.0.255 Wed Feb 23 22:20:10 2011 Initialization Sequence Completed The openvpn server has been configured to assign ip addresses in the range 10.8.0.* and the client has been given 10.8.0.50. When I run the following nmap from the client: Starting Nmap 5.00 ( http://nmap.org ) at 2011-02-23 22:04 EST Host 10.8.0.50 is up (0.00047s latency). Nmap done: 256 IP addresses (1 host up) scanned in 30.34 seconds Host 192.168.1.1 is up (0.0025s latency). Host 192.168.1.18 is up (0.074s latency). Host 192.168.1.41 is up (0.0024s latency). Host 192.168.1.55 is up (0.00018s latency). Nmap done: 256 IP addresses (4 hosts up) scanned in 6.33 seconds If I run an nmap from the server on 10.8.0.* I get nothing. If the client has two interfaces (wireless and tap device) when you look for a certain ip address, how does it decide which interface to connect on? edit I am trying to set up a vpn so that I can connect to my home network from a remote network. It seems like openvpn is connecting but none of the computers on my home network appear as network machines even after the connection is "Established". Stripped versions of the client and server config files are posted below. Thanks for any help you can offer. server.conf port 1194 proto udp dev tap ca /etc/openvpn/easy-rsa/keys/ca.crt cert /etc/openvpn/easy-rsa/keys/server.crt key /etc/openvpn/easy-rsa/keys/server.key # This file should be kept secret dh /etc/openvpn/easy-rsa/keys/dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 3 client.conf client dev tap dev-node tap0901 proto udp remote ********** 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client1.crt key client1.key comp-lzo verb 3 one other thing that might be helpful, I tried to connect using the openvpn gui for windows and the connection stalls out on "obtaining configuration" and the bar just scrolls forever.

  Read the article

• BIND - why duplicate nameserver entries (@ and *)?

  - by user27465

  I had to manually tweak my DNS service providers BIND file. BIND file, created by professional hosting company, before: $ORIGIN mycoolsite.com. $TTL 300 @ SOA ns1.cheapreg.com. registry.cheapreg.com. ( ... ) @ IN 3600 NS ns1.cheapreg.com. @ IN 3600 NS ns2.cheapreg.com. @ IN 3600 A 199.9.99.85 @ IN 3600 A 199.9.99.86 * IN 3600 A 199.9.99.85 * IN 3600 A 199.9.99.86 www IN 3600 A 199.9.99.85 www IN 3600 A 199.9.99.86 BIND file, created by layman, after: $ORIGIN mycoolsite.com. $TTL 300 @ SOA ns1.cheapreg.com. registry.cheapreg.com. ( ... ) @ IN 3600 NS ns1.cheapreg.com. @ IN 3600 NS ns2.cheapreg.com. * IN 3600 A 219.94.116.50 * IN 3600 A 219.94.116.51 * IN 3600 A 219.94.116.52 The difference is that the "pro"-file has duplicated the nameserver entries, once for @, and once for *, and I haven't. Any reason I should also duplicate nameserver entries (@ and *) ?

  Read the article

• Tracking down source of duplicate email messages in Outlook / Exchange environment

  - by Ken Pespisa

  I have a few users, who are also Blackberry users, that occasionally have duplicate emails generated from their "mailbox". I put mailbox in quotes because I'm not exactly sure where the duplicates are created. One of these users is in non-cached mode, and the other is in cached mode, and both experience the problem. In fact, the non-cached mode user was originally experiencing the problem while in cached mode, and I made the switch a few weeks ago to attempt to solve the problem. Today I discovered the issue still exists. I'm not sure if the fact that they are blackberry users could be causing the problem at all. I don't see how, but felt I should mention it anyway. Does anyone have ideas on how I might begin to troubleshoot this? I can see in the non-cached user's mailbox "Sent Items" that the message was sent only once. I confirmed the message does not state that there was a conflict and in fact that makes sense because they are in non-cached mode. On the server, we have a mail journaling feature turned on for our third-party mail archiving system, and I can see that that system sees two sent messages. And likewise, the recipient does in fact have two messages in their inbox with consecutive message IDs ([email protected]) and ([email protected]). It would seem to me that the duplicates are generated on the client, but is there a way to tell for sure?

  Read the article

• nginx : backend https, proxy_pass shows ip

  - by Vulpo

  I am using nginx as a reverse proxy listening at port 80 (http). I am using proxy_pass to forward requests to backend http and https servers. Everything works fine for my http server but when I try to reach the https server through nginx reverse proxy the ip of the https server is shown in the client's web browser. I want the uri of the nginx server to be shown instead of the https backend server's ip (once again, this works fine with the http server but not for the https server). See this post on the forum Here is my configuration file : server { listen 80; server_name domain1.com; access_log off; root /var/www; if ($request_method !~ ^(GET|HEAD|POST)$ ) { return 444; } location / { proxy_pass http://ipOfHttpServer:port/; } } server { listen 80; server_name domain2.com; access_log off; root /var/www; if ($request_method !~ ^(GET|HEAD|POST)$ ) { return 444; } location / { proxy_pass http://ipOfHttpsServer:port/; proxy_set_header X_FORWARDED_PROTO https; #proxy_set_header Host $http_host; } } When I try the "proxy_set_header Host $http_host" directive and "proxy_set_header Host $host" the web page can't be reached (page not found). But when I comment it, the ip of the https server is shown in the browser (which is bad). Does anyone have an idea ? My other configs files are : proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; #proxy_hide_header X-Powered-By; proxy_intercept_errors on; proxy_buffering on; proxy_cache_key "$scheme://$host$request_uri"; proxy_cache_path /var/cache/nginx levels=1:2 keys_zone=cache:10m inactive=7d max_size=700m; user www-data; worker_processes 2; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; access_log /var/log/nginx/access.log; server_names_hash_bucket_size 64; sendfile off; tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_comp_level 5; gzip_http_version 1.0; gzip_min_length 0; gzip_types text/plain text/html text/css image/x-icon application/x-javascript; gzip_vary on; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } Thanks for your help !

  Read the article

• Syncing two sheets, while being able to hide different data

  - by Joshua

  I'm pretty new to excel- so please bear with me. I have created a spreadsheet to organize gear by serial numbers and by who has it. This list is getting updated multiple times daily as gear shuffles regularly. I have gear that is assigned and unassigned. On the main sheet I have all the data, the way I want it to be organized. What I'm trying to do is duplicate this sheet, so that both sheets automatically keep the same data at all times, but on the first sheet I can hide all the unassigned gear, and view only the assigned gear, and then be able to narrow it down in groups using the hide function heavily. On the second sheet I want to be able to hide all of the assigned gear, and all the columns of gear that have no unassigned gear. End result will be that as gear is moved between individuals or is unassigned entirely, I make that adjustment on one sheet and the data stays the same on both, but the way I view that same sheet is different on both. If I'm making no sense just let me know and I'll try to explain again more clearly. Thanks

  Read the article

• OpenStack: How to make Cloudify use the floating IP instead of the fixed one?

  - by polslinux

  I have a problem with Cloudify (both 2.5 and 2.6-rc release). I have an All-In-One Openstack 2013.1.1 setup and I'm trying to use Cloudify to bootstrap a cirros 0.3.1 vm. My quantum configuration is: pool of fixed ip (10.0.0.0/24) for vm management; pool of floating ip (192.168.1.170-190) taken from 192.168.1.1/24 (my lan) When I deploy a vm first, an ip from 10.0.0.0/24 is given (I cannot reach it from my PCs because it is only for vm management) and then I associate a floating ip with which I can ping (and ssh) the deployed machine. The problem is when I do: bootstrap-cloud openstack because Cloudify stay forever into "attempting to access management vm 10.0.0.3" and this is due to the fact that 10.0.0.3 is not reachable. What can I do to get Cloudify take the floating ip instead of the fixed one?

  Read the article

• How can I work out how many IP addresses there are in a given range?

  - by Jarede

  I'm wondering if there is a formula to work out the amount of IP addresses in a given range. I have a system that takes either a single IP address or a start and and end IP address: A single one might be: 145.16.23.241 A range might be: 145.16.23.122 - 145.16.23.144 The people inputting these aren't technical, nor are they receiving these details from technical people, so suggesting using CIDR notation isn't an answer for me. I want to be able to highlight that when entering a range such as: 122.100.10.12 - 128.10.200.140 it might not actually be a range and rather 2 singular IP addresses since such a range would comprise of x (large number of) IP addresses. Is there a basic formula to help me highlight this?

  Read the article

• SMTP Client implementation [on hold]

  - by orif

  I'm implementing SMTP client. What should the client do once it already sent the "." at the end of the mail, but didn't receive "250 Ok"? This is how the conversation between the client and server look like: Server Response: 220 www.sample.com ESMTP Postfix Client Sending : HELO domain.com Server Response: 250 Hello domain.com Client Sending : MAIL FROM: <[email protected]> Server Response: 250 Ok Client Sending : RCPT TO: <[email protected]> Server Response: 250 Ok Client Sending : DATA Server Response: 354 End data with <CR><LF>.<CR><LF> Client Sending : Subject: Example Message Client Sending : From: [email protected] Client Sending : To: [email protected] Client Sending : Client Sending : TEST MAIL Client Sending : Client Sending : . Server Response: 250 Ok: queued as 23411 Client Sending : QUIT I'm not sure what should I do if the client sends "." and doesn't receive the 250 Ok - because of possible network error. Was the "." sent or not? Should the client resend the mail - and - maybe - duplicate the item, or not - and risk in losing an important mail item? Thank you.

  Read the article

• Can no longer duplicate display to external monitor on Windows 7

  - by rbeier

  We have a large TV at work - I connect my laptop to it to share my screen during meetings. Until today, my laptop display has been duplicating to the TV automatically when I connect the TV cable to the laptop. The display resolution would decrease automatically to be compatible with the TV. Today, however, it's stopped working. When I connect the cable to the TV, the display extends rather than duplicating. Using the Win+P key combination (or Fn+F7 on my Lenovo laptop), I can choose to duplicate the display - but when I do this, it ends up only displaying on the laptop. I can get it to display on the TV by hitting Win+P and choosing "projector only", but then I can't see what I'm doing on the laptop screen. I have a Lenovo W520 laptop running Windows 7, connected to the TV using a DisplayPort-to-HDMI converter cable. The TV's native resolution is 1280x720; the laptop's native resolution is 1600x900. I've tried booting with the TV cable already connected; I've tried manually lowering the display resolution on the laptop to 1280x720 before duplicating the display. Neither works. Does anyone have any other suggestions?

  Read the article

• Windows 7 constantly accessing hard drive [duplicate]

  - by Zohar

  Possible Duplicate: Tool which finds which process is causing the heavy hard drive activity? Did you notice that on Windows 7 (I use 64-bit) the hard drive LED is constantly blinking, which means that the OS is constantly wearing the hard drive by accessing it? It's something related to the system process, and it even occurs in safe mode, so I don't think it's a third party software problem. Has anyone experienced this problem as well, and is it a Windows problem, or caused by something else? Edit: My indexing service is reduced to indexing only the Start Menu. Even if it was set for the whole computer, it would eventually stop; that's not it. My friends also suffer from the same problem. Please answer my first question: have any of you have seen a Windows 7 machine whose hard drive LED is at rest? I'm also trying to track down the offending process using procmon and Resource Monitor, and it actually seems like a system process. It could also be svchost.exe, and I'm not sure which file they are accessing since I see a lot of activity which I can't make sense of. It's loading system DLLs, accessing registry keys, and other nonsense.

  Read the article

• Setting up an IP Camera with silverlight

  - by Sean

  I am trying to set up an IP camera and have it work through Silverlight I am using both Microsoft Expression and Microsoft Visual Studio 2008. I am able to do encoding with a usb connected web cam but I cannot find a way to use the encoder to connect to ip camera connected to our switch. Does anyone have experience setting up an ip camera to encode into the Silverlight framework?

  Read the article

• Cannot ping ubuntu server by hostname - can only ping by IP

  - by Tone

  I have an unbuntu 9.10 server and have set the hostname to "fileserver" When I try to ping fileserver from a client machine it doesn't find it, however I can ping by the IP my router assigns it. I have tried changing the ip in /etc/hosts from this: 127.0.0.1 fileserver to this: 192.168.1.109 fileserver which is the ip being assigned. I had a previous install of this server and i had no issues with this - only difference in this install is i did not select any of the options such as LAMP, OpenSSH, etc during the install process. I can access the machine fine by ip using PuTTY. Any ideas?

  Read the article

• What is the iPhone simulator IP address?

  - by Chris G

  Hi I have been looking for the answer to this question for some time. I am doing network programming for the iPhone and it is necessary for me to use the IP address of the device. This isn't a problem on the physical device as it has its own IP address on the network. However I was wondering what was the case with it on the simulator. Does it get assigned an IP address to be used? Thanks in advanced for any help, CG

  Read the article

• how to verify browser IP for server-side web service

  - by Anthony

  I have a web service that needs to be able to verify the end-user's IP that called the server-script that is requesting the web service. Simple layout: Person A goes to Webpage B. Webpage B calls Web Service C to get some info on Person A. Web Service C won't give Webpage B the requested information without confirmation that the request originated from Person A's IP and not someone who has stolen Person A's session. I'm thinking that for a browser-based solution, the original site (Webpage B) can open an iframe that goes to the Web Service's authentication page. A key of some kind is passed to the browser which will some how indicate both the user's IP and Web Page B's IP, so that the Web Service can confirm that no one has nabbed anything. I have two challenges, but I'll stick to the more immediate one first: I'm not sure if my browser-based plan really makes sense. If someone steals the session cookie, how is the Web Service going to know? Would this cookie be held be Web Page B and thus be harder to steal? Is it a sound assumption that a cookie or key held by the server only and not the browser is safe? Also, would the web service, based on the iframe initial connection, be expecting the server/user-ip combo? What I mean is, does the session key provided via the iframe get stored by the web service and the Web Site B shows it has a match? Or is the session key more generic, meaning the web service is passed the key by Website B and the Web Service verifies that this is a valid session key based on what a valid session key should look like?

  Read the article

< Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >