Search Results

Search found 5287 results on 212 pages for 'physical computing'.

Page 66/212 | < Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >

• 12.04 wired network doesn't work RTL8111/8168B

  - by laket

  its a fresh 12.04 install 64bits. wifi works fine, wired stays off with cable connected and network-manager shows as if cable is disconnected. Turning off networking lights up my network-cards leds, turning networking on shuts off the leds and no communication is possible. I already tried, turning off the network-manager (sudo service network-manager stop) and setting up my eth0 manually, as soon as I switch off the network-manager my leds light up, but after setting up manually eth0 (sudo ifconfig eth0 10.2.10.114 netmask 255.255.0.0 up) the leds turn off again. I am still dual booting with 10.04 where I have no issues at all, leaving the cable connected all time to my notebook and a switch. Here is some hardware info: lshw: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 03 serial: c8:0a:a9:d7:05:97 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168d-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff memory:f0010000-f001ffff lspci: 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) ifconfig eth0: eth0 Link encap:Ethernet HWaddr c8:0a:a9:d7:05:97 inet addr:10.2.10.114 Bcast:10.2.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0xc000 cat /etc/network/interfaces: (already tried here with and w/o eth0) auto lo eth0 iface lo inet loopback cat /etc/NetworkManager/NetworkManager.conf [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false Any help is welcome ;) Laket

  Read the article

• Problem with APTonCD application

  - by Harikrishnan

  I created a iso image using aptoncd & burned it to a dvd. Now when i tried to restore, the program does not detect the dvd in the drive. It shows "Please insert a disc in the drive." and if we click "ok" it shows E: Failed to mount the cdrom. The dvd is in the drive itself. I tried sudo lshw -C disk and the output is: *-cdrom description: DVD-RAM writer product: DVDRAM GH22NS50 vendor: HL-DT-ST physical id: 1 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd0 logical name: /dev/sr0 logical name: /media/APTonCD logical name: /media/apt version: TN02 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 mount.fstype=iso9660 mount.options=ro,relatime,uid=1000,gid=1000,iocharset=utf8,mode=0400,dmode=0500 state=mounted status=ready *-medium physical id: 0 logical name: /dev/cdrom logical name: /media/APTonCD logical name: /media/apt configuration: mount.fstype=iso9660 mount.options=ro,relatime,uid=1000,gid=1000,iocharset=utf8,mode=0400,dmode=0500 state=mounted Then i checked in disk utility application. in that dvd rom is shown as /dvd/sr0 My ubuntu version is 10.10. Please help me to solve the problem.

  Read the article

• Script to recursively grep data from certain files in the directory

  - by Jude

  I am making a simple shell script which will minimize the time I spend in searching all directories under a parent directory and grep some things inside some files. Here's my script. #!/bin/sh MainDir=/var/opt/database/1227-1239/ cd "$MainDir" for dir in $(ls); do grep -i "STAGE,te_start_seq Starting" "$dir"/his_file | tail -1 >> /home/xtee/sst-logs.out if [ -f "$dir"/sysconfig.out]; then grep -A 1 "Drive Model" "$dir"/sysconfig.out | tail -1 >> /home/xtee/sst-logs.out else grep -m 1 "Physical memory size" "$dir"/node0/setupsys.out | tail -1 >> /home/xtee/sst-logs.out fi done The script is supposed to grep the string STAGE,te_start_seq Starting under the file his_file then dump it sst-logs.out which it does. My problem though is the part in the if statement. The script should check the current directory for sysconfig.out, grep drive model and dump it to sst-logs.out if it exists, otherwise, change directory to node0 then grep physical memory size from setupsys.out and dump it to sst-logs.out. My problem is, it seems the if then else statement seems not to work as it doesn`t dump any data at all but if i execute grep manually, i do have data. What is wrong with my shell script? Is there any more efficient way in doing this?

  Read the article

• Yoga Pro 2 Wi-Fi not working

  - by user293004

  I installed Ubuntu 14.04 on my new Yoga Pro 2 and the wireless is not working. It started with Windows 8 on it. The Network Manager says Wi-Fi is disabled by hardware switch. I tried putting a blacklist file in ect/modprobe.d as has been suggested in many places. I called the file "blacklist-ideapad_laptop.conf" and wrote in the file blacklist ideapad_laptop I checked to make sure that the wireless is enabled in the BIOS. It is. I ran rfkill list all and it displayed: 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I ran iwlist wlan0 scan and it displayed: wlan0 Failed to read scan data : Network is down I ran sudo rmmod ideapad_laptop and it displayed: rmmod: ERROR: Module ideapad_laptop is not currently loaded. I ran ifconfig wlp1s0 up and it displayed: wlp1s0: ERROR while getting interface flags: No such device. I ran "lspci" and it displayed: 01:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b) I ran sudo lshw -c network and it displayed: *-network DISABLED description: Wireless interface product: Wireless 7260 vendor: Intel Corporation physical id: 0<br> bus info: pci@0000:01:00:0.0 logical name: wlan0 version: 6b serial: 7c:7a:91:5f:9b:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-24-generic firmware=22.24.8.0 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:61 memory:b0400000-b0401fff This No wireless with Intel Centrino Advanced-N 7260 seems to be dealing with a similar issue. It suggests that I need to update my firmware. So I downloaded iwlwifi-7260-ucode-23.214.9.0 from Intel's website. I put the file "iwlwifi-7260-9.ucode" in /lib/firmware and ran "sudo lshw -c network" again. It displayed exactly as before. Is there something else I need to do install the new firmware?

  Read the article

• Can't access external hard drives or thumb drives

  - by calden

  I am not a complete linux noob but I don't know a lot either and would greatly appreciate some help with this. I just installed Ubuntu 10.10 onto my laptop. Everything is working great however USB devices such as thumb drives and external hard drives wont show up. I have been looking around a bit and when I run sudo fdisk -l it displays this: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00065684 Device Boot Start End Blocks Id System /dev/sda1 * 1 29255 234983424 83 Linux /dev/sda2 29255 30402 9212929 5 Extended /dev/sda5 29255 30402 9212928 82 Linux swap / Solaris Disk /dev/sdb: 16.0 GB, 16026435072 bytes 64 heads, 32 sectors/track, 15283 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000df90d Device Boot Start End Blocks Id System /dev/sdb1 * 1 15283 15649776 7 HPFS/NTFS It does seem to display my 16 gig thumb drive but other then seeing it here I cant access it to read and write files to it. It does the same with my external hard drive. I know those devices work as I have tried them on my other computer and they are working fine. Also this is what is in fstab if this will help anybody help me: proc /proc proc nodev,noexec,nosuid 0 0 /dev/sdb1 / ext4 errors=remount-ro 0 1 /dev/sdb5 none swap sw 0 0 Thank you very much for the help everyone.

  Read the article

• Ubuntu installer does not show drives

  - by Tanweer Rashid

  I am trying to install Ubuntu 12.04 LTS on my Inspiron laptio, but the installer does not show any drives. My system has a 1TB SATA drive and a 32GB SSD. As far as I can figure, the boot files are kept on the SSD for fast startup (for Windows). During Win7 installation, I had to manually load drivers for RAID controller to see all available drives. Running fdisk -l from the live CD shows the following: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x234b4782 Device Boot Start End Blocks Id System /dev/sda1 63 80324 40131 de Dell Utility /dev/sda2 * 81920 41627647 20772864 7 HPFS/NTFS/exFAT /dev/sda3 41627648 357019647 157696000 7 HPFS/NTFS/exFAT /dev/sda4 357019648 1953517567 798248960 f W95 Ext'd (LBA) /dev/sda5 672415744 1312966655 320275456 7 HPFS/NTFS/exFAT /dev/sda6 1312968704 1953517567 320274432 7 HPFS/NTFS/exFAT Disk /dev/sdb: 32.0 GB, 32017047552 bytes 255 heads, 63 sectors/track, 3892 cylinders, total 62533296 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x234b474b Device Boot Start End Blocks Id System /dev/sdb1 2048 16775167 8386560 84 OS/2 hidden C: drive ubuntu@ubuntu:~$ In the Ubuntu installer, I can only choose /dev/sdb for "Device for boot loader installation", and sdb doesn't show any drives. I cannot select /dev/sda. Any ideas anyone? Thanks.

  Read the article

• How do I get Graphics drivers / bluetooth / card reader working on an Acer Aspire V3-571G?

  - by Adam

  A couple of days ago I bought an Acer Aspire V3-571G laptop without a system installed on it. The only thing that was there was Linux Linpus. I created a bootable CD with Ubuntu 12.04 64-bit - I read that my processor was 64 bit and that it might be a good configuration for my gear (I'm not especially fluent with all the computer stuff, still trying to learn) and replaced Linpus with Ubuntu. Everything seemed to work fine, but there're few exceptions to that which came pass my way. My bluetooth doesn't work. It seems to be switched on, but when I check my system settings the button is actually off, and I can't drag it 'perminently' to the 'on' position. Tried a couple of commands I found on the net, none of them helped and there was no word whatsoever in my BIOS settings about enabling bluetooth. My card reader has some serious problems with copying more than one file at a time. I tried to put some music on my phone through a MicroSD card adapter (because my bluetooth doesn't work) and it got stuck every single time I copied an album on it. I'm not sure if all my drivers were properly installed, so I checked in the terminal if it could tell me sth about my graphics. typed: sudo lshw -c display and what i got was: *-display UNCLAIMED description: VGA compatible controller product: NVIDIA Corporation vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller cap_list configuration: latency=0 resources: memory:b2000000-b2ffffff memory:a0000000-afffffff memory:b0000000-b1ffffff ioport:2000(size=128) *-display description: VGA compatible controller product: Ivy Bridge Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:44 memory:b3000000-b33fffff memory:c0000000-cfffffff ioport:3000(size=64) As I said I'm no expert and not english-speaking generally, but it doesn't seem to be right. I've got a NVIDIA GeForce GT 640M.

  Read the article

• How do I get a Belkin F5D8053 wireless adapter working?

  - by disassembler

  I've tried getting my Belkin N Wireless adapter to work on Ubuntu many times with no luck at all. Each time I seem to arrive at a dead end. After some thorough searching of UbuntuForums and WifiDocs I've gathered some information and narrowed the problem down to an issue with the rtl819xU driver. Here's some info that may help: $ sudo lshw -C network *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:22:75:38:52:ac capabilities: ethernet physical wireless configuration: broadcast=yes driver=rtl819xU multicast=yes wireless=802.11b/g/n $ sudo lsmod Module Size Used by vesafb 13449 1 snd_ice1724 106559 2 snd_ice17xx_ak4xxx 13163 1 snd_ice1724 snd_ac97_codec 105614 1 snd_ice1724 ac97_bus 12642 1 snd_ac97_codec snd_ak4xxx_adda 18436 2 snd_ice1724,snd_ice17xx_ak4xxx snd_ak4114 14326 1 snd_ice1724 snd_pt2258 12986 1 snd_ice1724 snd_i2c 13831 2 snd_ice1724,snd_pt2258 snd_ak4113 14307 1 snd_ice1724 snd_pcm 80244 4 snd_ice1724,snd_ac97_codec,snd_ak4114,snd_ak4113 fglrx 2434640 121 snd_seq_midi 13132 0 snd_rawmidi 25269 2 snd_ice1724,snd_seq_midi binfmt_misc 13213 1 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event ppdev 12849 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq dcdbas 14054 0 r8192u_usb 297246 0 snd 55295 16 snd_ice1724,snd_ac97_codec,snd_ak4xxx_adda,snd_ak4114,snd_pt2258,snd_i2c,snd_ak4113,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd parport_pc 32111 1 snd_page_alloc 14073 1 snd_pcm shpchp 32345 0 lp 13349 0 parport 36746 3 ppdev,parport_pc,lp usbhid 41704 0 hid 77084 1 usbhid e100 40108 0 floppy 60032 0 $ sudo iwconfig wlan0 802.11b/g/n Mode:Managed Access Point: Not-Associated Bit Rate:1 Mb/s Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I'd like to know if 1) Is the driver is properly installed and recognized by Ubuntu? 2) What can I do to load the drivers properly and make use of the adapter? Thanks!

  Read the article

• Discs in DVD Drive not being read

  - by I Heart Ubuntu

  Does anyone have an experience with Ubuntu that is no longer reading discs in the DVD drive? This is my first time Ubuntu does not see the disc :| The disc is fine and works on my other Ubuntu computers. The drive is there and powered. I can even type in eject in a terminal and the drive will open. Using the command: sudo lshw -C disk I am able to see info about my drive too. Actually BOTH of my internal DVD drives cannot read discs anymore. If the output is not readable below, here is the info in pastebin. http://pastebin.com/GqqSCTPw *-cdrom:0 description: DVD writer product: DVD_RW ND-3500AG vendor: _NEC physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/cdrom1 logical name: /dev/cdrw1 logical name: /dev/dvd1 logical name: /dev/dvdrw1 logical name: /dev/scd0 logical name: /dev/sr0 version: 2.1B serial: [_NEC DVD_RW ND-3500AG2.1B06022300BT-LIGGY capabilities: removable audio cd-r cd-rw dvd dvd-r configuration: ansiversion=5 status=nodisc *-cdrom:1 description: DVD-RAM writer product: CDDVDW SH-S222A vendor: TSSTcorp physical id: 0.1.0 bus info: scsi@0:0.1.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd1 logical name: /dev/sr1 version: SB01 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc

  Read the article

• Wireless drops on HP ENVY dv6 with RT3290 wireless, worked without problem prior to upgrading to Ubuntu 13.10, can it be fixed?

  - by Tim

  I have a HP ENVY dv6 Notebook PC with an AMD A10 quad core and RT3290 wireless. Since I upgraded from Ubuntu 13.04 to 13.10, the wireless connects, but then drops after a few minutes or longer, whether or not I am running openconnect to get through a VPN. If I attempt to run a remote X client (e.g. remote xterm) it drops. If I don't run an X client, it disconnects after a while, requiring a reload of the driver and reconnect. Wireless info... sudo lshw -c network *-network description: Wireless interface product: RT3290 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 68:94:23:a7:09:cb width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.11.0-12-generic firmware=0.37 ip=192.168.1.115 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:55 memory:f0210000-f021ffff I have successfully built and installed the MediaTek driver with no luck on connecting, then the system hangs on reboot and I have to recover/undo the changes to boot successfully.

  Read the article

• Deleting Unused Swaps Partions

  - by Nikita Kononov

  Good evening everyone , I got a little issue with Swap Partitions. Due to some issues after installing Ubuntu first time, I reinstalled it and now I have 3 Swaps. Here is sudo fdisk -l result Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xaa9693fe Device Boot Start End Blocks Id System /dev/sda1 2048 52430847 26214400 1c Hidden W95 FAT32 (LBA) /dev/sda2 * 52430848 540677076 244123114+ 7 HPFS/NTFS/exFAT /dev/sda3 540678142 1465147391 462234625 5 Extended Partition 3 does not start on physical sector boundary. /dev/sda5 1452750848 1465147391 6198272 82 Linux swap / Solaris /dev/sda6 1440352256 1452742655 6195200 82 Linux swap / Solaris /dev/sda7 540678144 1427951615 443636736 83 Linux /dev/sda8 1427953664 1440339967 6193152 82 Linux swap / Solaris So Swaps in /dev/sda5 and /dev/sda6 are no longer in use as far as I understand and thus I was planning to delete them, however faced a problem. What I did is download and burn Gparted Live CD and boot it up, tried to delete those partitions but I have no idea how to add 12GB unallocated memory to the existing OS partition in this case to /dev/sda7 Is there anyway I can delete 2 swaps and extend unallocated memory to /dev/sda7 partion? Thank you in advance!

  Read the article

• Trendnet tew-424ub wireless not working after update 12.10

  - by dwa

  I updated packages from the software manager and now my wireless won't work. It's a Trendnet tew-424ub iwconfig says lo no wireless extensions. eth0 no wireless extensions. sudo lshw -C network: description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 1c:6f:65:46:e9:d4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.137 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:de00(size=256) memory:fdaff000-fdafffff memory:fdae0000-fdaeffff memory:fda00000-fda0ffff lsusb: Bus 003 Device 002: ID 0bc2:3332 Seagate RSS LLC Expansion Bus 003 Device 003: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 006: ID 0457:0163 Silicon Integrated Systems Corp. 802.11 Wireless LAN Adapter Bus 005 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 005: ID 0781:5530 SanDisk Corp. Cruzer Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Help? I'm not sure where to start. I've been browsing forums and such for a long time and nothing I try is working.

  Read the article

• SD Card only mounted after a reboot

  - by hattenn

  I have a Kingston 2GB MicroSD and I plug it in via an inconix MicroSD Adapter to the internal card reader of my Samsung N210 Netbook with Ubuntu 10.10, but it doesn't show up. Only if I reboot the system when the card's plugged in it shows up. Why does it need a reboot for mounting? sudo fdisk -l gives the output below. But I can only see the drive when I reboot the computer while the card's plugged. Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9a5a7990 Device Boot Start End Blocks Id System /dev/sda1 1 1959 15728640 27 Unknown Partition 1 does not end on cylinder boundary. /dev/sda2 * 1959 1972 102400 7 HPFS/NTFS /dev/sda3 1972 18992 136718750 83 Linux /dev/sda4 18992 19458 3738625 5 Extended /dev/sda5 18992 19458 3738624 82 Linux swap / Solaris Disk /dev/sdb: 1973 MB, 1973420032 bytes 60 heads, 59 sectors/track, 1088 cylinders Units = cylinders of 3540 * 512 = 1812480 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1089 1927100+ 6 FAT16

  Read the article

• Ubuntu installation does not recognize drive partinioning

  - by Woltan

  I have a 1TB drive and installed Windows 7 on a 128GB partition. When I now try to install Ubuntu 11.04 it does not recognize the Windows partition but offers the complete 1TB drive to install Ubuntu on instead. It displays: However, in the Ubuntu Disk Utility the Windows partitions are recognized. What do I need to do in order for Ubuntu to recognize the Windows 7 partition and install Ubuntu as a dual boot? Response to comments The following commands were executed and the results are shown below: fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x34a38165 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 16318 130969600 7 HPFS/NTFS Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x14a714a6 Device Boot Start End Blocks Id System /dev/sdb1 1 60801 488384001 83 Linux parted -l Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: /dev/sr0: unrecognised disk label

  Read the article

• Grub does not show a Windows 8 option after dual boot

  - by skytreader

  So, I've successfully dual-booted my Windows 8 machine with Ubuntu 12.04 . However, I still don't have a convenient method of choosing what OS to load at boot time. After installing Ubuntu, my computer still loads Windows 8 directly. I then added grubx64.efi to the white list of my boot loader. But after that, my machine loads Ubuntu directly without even a shadow of GRUB showing up! I used boot-repair and I got this paste.ubuntu URL: paste.ubuntu.com/1326074. After running boot-repair (and re-white listing the grubx64.efi file), GRUB now shows up but without any Windows 8 option! Lastly, I ran sudo fdisk -l and it gave me this: WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x6396389f Device Boot Start End Blocks Id System /dev/sda1 1 1465149167 732574583+ ee GPT Partition 1 does not start on physical sector boundary. I'm guessing my problem has something to do with the warning from fdisk above but I don't know what to do with it. How do I proceed now?

  Read the article

• Extension GLX missing...on a desktop PC

  - by Bart van Heukelom

  I just installed Ubuntu 12.10 on a new PC with an Nvidia GTX 560 graphics card, but after installing the Nvidia proprietary drivers (either -current or -current-updates), Unity won't start. When trying to start it manually I get the message "extension GLX missing". I've searched around and found results like this question which point out it's a problem with Nvidia Optimus laptops. However, I don't have this problem on a laptop, but on a desktop PC. lshw output for the graphics card: *-display description: VGA compatible controller product: GF114 [GeForce GTX 560 SE] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nouveau latency=0 resources: irq:16 memory:f4000000-f5ffffff memory:e0000000-e7ffffff memory:e8000000-ebffffff ioport:e000(size=128) memory:f6000000-f607ffff and CPU: *-cpu description: CPU product: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz vendor: Intel Corp. physical id: 40 bus info: cpu@0 version: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz slot: SOCKET 0 size: 1600MHz capacity: 3800MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid fsgsbase smep erms cpufreq configuration: cores=4 enabledcores=4 threads=4

  Read the article

• Ubuntu server 11.04 recognize only 1 core instead of 4

  - by Kreker

  I searched for other questions and googled a lot but I don't find a solution for solving this problem. Ubuntu Server 11.04 64bit installed on Dell Poweredge with Intel Xeon X5450. He only recognize 1 of the 4 cores I have. Tried to modify the GRUB config but didn't work. IN the machine BIOS I didn't find anything useful. CPU root@darwin:~# cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Xeon(R) CPU X5450 @ 3.00GHz stepping : 10 cpu MHz : 2992.180 cache size : 6144 KB physical id : 0 siblings : 1 core id : 0 cpu cores : 1 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm dca sse4_1 xsave lahf_lm dts tpr_shadow vnmi flexpriority bogomips : 5984.36 clflush size : 64 cache_alignment : 64 address sizes : 38 bits physical, 48 bits virtual power management: GRUB root@darwin:~# cat /etc/default/grub # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 #GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=2 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="" GRUB_CMDLINE_LINUX="noapic nolapic" #was with acpi=off # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux #GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1" Complete dmesg Too long, posted on pastebin http://pastebin.com/bsKPBhzu

  Read the article

• Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

  - by user1622959

  A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

  Read the article

• Why does Ubuntu 13.10 not detect my Win7 partition?

  - by goutham

  I'm trying to install Ubuntu 13.10 alongside Windows 7 on my DELL INSPIRON 14z 5423 laptop and I'm new to all of this. I'm using the Ubuntu 13.10 64-bit ISO burned onto a CD. The first time I tried to install it, Ubuntu said it did not detect any other OS, which meant I only had 4 options: Erase disk and install Ubuntu (I don't want to do this) Encrypt new Ubuntu. Use LVM. Something else. If I choose the Something else option, it brings me to the partition menu and says that I have 1 disk with free space of (500Gb), but that's not true because I have Windows 7. I restarted the laptop several times and booted the CD again and I got exactly the same as I did previously. How do fix this problem and install Ubuntu alongside Windows 7? After executing "sudo fdisk -l" command in terminal ubuntu@ubuntu:~$ sudo fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xd2b811c5 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 314574847 157184000 7 HPFS/NTFS/exFAT /dev/sda3 314574848 629147647 157286400 7 HPFS/NTFS/exFAT /dev/sda4 629147648 976771071 173811712 7 HPFS/NTFS/exFAT After removing one partition I executed command once again ubuntu@ubuntu:~$ sudo fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xd2b811c5 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 629145599 314469376 7 HPFS/NTFS/exFAT /dev/sda3 629147648 976771071 173811712 7 HPFS/NTFS/exFAT

  Read the article

• How to Manage and Use LVM (Logical Volume Management) in Ubuntu

  - by Justin Garrison

  In our previous article we told you what LVM is and what you may want to use it for, and today we are going to walk you through some of the key management tools of LVM so you will be confident when setting up or expanding your installation. As stated before, LVM is a abstraction layer between your operating system and physical hard drives. What that means is your physical hard drives and partitions are no longer tied to the hard drives and partitions they reside on. Rather, the hard drives and partitions that your operating system sees can be any number of separate hard drives pooled together or in a software RAID Latest Features How-To Geek ETC Inspire Geek Love with These Hilarious Geek Valentines How to Integrate Dropbox with Pages, Keynote, and Numbers on iPad RGB? CMYK? Alpha? What Are Image Channels and What Do They Mean? How to Recover that Photo, Picture or File You Deleted Accidentally How To Colorize Black and White Vintage Photographs in Photoshop How To Get SSH Command-Line Access to Windows 7 Using Cygwin How to Kid Proof Your Computer’s Power and Reset Buttons Microsoft’s Windows Media Player Extension Adds H.264 Support Back to Google Chrome Android Notifier Pushes Android Notices to Your Desktop Dead Space 2 Theme for Chrome and Iron Carl Sagan and Halo Reach Mashup – We Humans are Capable of Greatness [Video] Battle the Necromorphs Once Again on Your Desktop with the Dead Space 2 Theme for Windows 7

  Read the article

• How to install Ubuntu 12.04.1 in EFI mode with Encrypted LVM?

  - by g0lem

  I'm trying to properly install Ubuntu 12.04.1 LTS 64-bit PC (AMD64) with the alternate install CD ".iso" on a lenovo Thinkpad X220. Default Hard Disk (with a pre-installed version of Windows 7) has been replaced with a brand new SSD. The UEFI BIOS of the lenovo Thinkpad X220 is set to "UEFI Boot only" & "USB UEFI BIOS Support" is enabled (I'm using an external USB DVD reader to perform Ubuntu installation). The BIOS is a Phoenix SecureCore Tiano, BIOS version is 8DET56WW (1.26). The attempts below are made with the UEFI BIOS settings described above. Here's what I've tried so far: Boot on a live GParted CD Create a GPT partition table Create a FAT32 partition for UEFI System, set the partition to "EF00" type ("boot" flag) Leave remaining space unformated Boot on Ubuntu 12.04.1 LTS 64-bit PC (AMD64) with alternate CD: Perform the install with network updates enabled Use manual partitioning FAT32 partition created with GParted is used as "EFI System partition" Remaining space is set to be used as "Physical volume for LVM" Then "Configure encrypted volumes" using the previous "Physical volume for LVM" as the encrypted container, passphrase is setup. "Configure the Logical Volume Manager" creating a volume Group using the encrypted container /dev/mapper/sda2_crypt Creation of the Logical Volumes "Create logical volume", choosing the previously created volume Group Assign a mount point and file system to the Logical volumes : LV-root for / LV-var for /var LV-usr for /usr LV-usr-local for /usr/local LV-swap for swap LV-home for /home NOTE: /tmp would be in RAM only using TMPFS Bootloader step: neither my ESP partition (/dev/sda1, /dev/sda or MBR) seems to be the right place for GRUB, I get the following message (X suffix is for demonstration only): unable to install grub in /dev/sdaX Executing 'grub-install /dev/sdaX' failed This is a fatal error. Finish installation without the Bootloader & Reboot The system doesn't start, there's no EFI/GRUB menu at startup. What are the steps to perform a clean and working installation of Ubuntu 12.04.1 Precise Pangolin, 64bit version in U(EFI) mode using the encrypted LUKS + LVM scheme described above?

  Read the article

• Problem with APTonCD application

  - by Harikrishnan

  I created a iso image using aptoncd & burned it to a dvd. now when i tried to restore, the program does not detect the dvd in the drive. It shows "Please insert a disc in the drive." and if we click "ok" it shows "E: Failed to mount the cdrom.". The dvd is in the drive itself. I tried "sudo lshw -C disk" and the out put is: *-cdrom description: DVD-RAM writer product: DVDRAM GH22NS50 vendor: HL-DT-ST physical id: 1 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd0 logical name: /dev/sr0 logical name: /media/APTonCD logical name: /media/apt version: TN02 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 mount.fstype=iso9660 mount.options=ro,relatime,uid=1000,gid=1000,iocharset=utf8,mode=0400,dmode=0500 state=mounted status=ready *-medium physical id: 0 logical name: /dev/cdrom logical name: /media/APTonCD logical name: /media/apt configuration: mount.fstype=iso9660 mount.options=ro,relatime,uid=1000,gid=1000,iocharset=utf8,mode=0400,dmode=0500 state=mounted Then i checked in disk utility application. in that dvd rom is shown as "/dvd/sr0". my ubuntu version is 10.10. please help me to solve the problem.

  Read the article

• How do I know if I'm getting the most out of my video card?

  - by b.long

  My computer at home is a bit lacking, so I want to make sure I'm getting the most out of it while I can. Generally speaking, here are the specs: 4GB Memory AMD Athlon(tm) 64 X2 Dual Core Processor 5200+ × 2 64-bit Ubuntu The terminal shows me the following: me@home:~$ uname -a Linux home 3.0.0-17-generic #30-Ubuntu SMP Thu Mar 8 20:45:39 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux me@home:~$ lspci | grep VGA 01:00.0 VGA compatible controller: ATI Technologies Inc RV380 [Radeon X600 (PCIE)] me@home:~$ sudo lshw -C video *-display:0 description: VGA compatible controller product: RV380 [Radeon X600 (PCIE)] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:44 memory:e0000000-efffffff ioport:ac00(size=256) memory:fdef0000-fdefffff memory:fdec0000-fdedffff *-display:1 UNCLAIMED description: Display controller product: RV380 [Radeon X600] vendor: ATI Technologies Inc physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress bus_master cap_list configuration: latency=0 resources: memory:fdee0000-fdeeffff me@home:~$ lspci -nn | grep VGA 01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV380 [Radeon X600 (PCIE)] [1002:5b62] The additional drivers menu in System Settings shows me nothing useful and my attempt at installing ATI's Catalyst Control center (drivers that came with the video card) failed. I believe the latest version of Ubuntu at the time was 9.x. What should I do? Install an old version of Ubuntu 9? Use some alternative driver? UPDATE: I might try my hand at a bit from this answer next: "Installing Catalyst Manually (from AMD/ATI's site)" . From a terminal, fgl_glxgears returns *"fgl_glxgears: command not found"*. Any thoughts?

  Read the article

• Desktop goes blurry / granulated

  - by Bonfire

  After few minutes using, desktop and fonts in unity-menu goes blurry. See screenshot.! In all applications (browser etc.) graphics seem to be allright. After rebooting problem disappears for few minutes. Changing the wallpaper also makes the desktop clear (for a while) but fonts are still blurry. I have ubuntu 12.04 and windows xp dualbooted. lspci: 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) 00:02.1 Display controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) lshw -c video: *-display:0 description: VGA compatible controller product: 82945G/GZ Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:16 memory:d0100000-d017ffff ioport:30c0(size=8) memory:c0000000-cfffffff memory:d0180000-d01bffff *-display:1 UNCLAIMED description: Display controller product: 82945G/GZ Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 02 width: 32 bits clock: 33MHz capabilities: cap_list configuration: latency=0 resources: memory:40000000-4007ffff Have you got any ideas to get this solved? Thank you very much! Bonfire

  Read the article

• Low Graphics and laggy screen after update to 13.10 from 13.04

  - by Wh0RU

  After updating from 13.04 to 13.10 many of 3D unity stuff has stopped working, I am suing Samsung Series 3 (NP350V5X) Laptop which has Switchable Intel and AMD Radeon HD 7670M GFX. xserver-xorg-video-ati does works but NO 3D support and graphics are very low. [I am currently using this] fglrx & fglrx-updates shows blank screen after Login. Intel Graphic Install doesn't work either (dependency error) Output of $ sudo lshw -c video *-display description: VGA compatible controller product: Thames [Radeon HD 7500M/7600M Series] vendor: Advanced Micro Devices, Inc. [AMD/ATI] physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:45 memory:e0000000-efffffff memory:c0120000-c013ffff ioport:3000(size=256) memory:c0100000-c011ffff *-display description: VGA compatible controller product: 3rd Gen Core processor Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:bfc00000-bfffffff memory:d0000000-dfffffff ioport:4000(size=64) Similarly $ /usr/lib/nux/unity_support_test -p OpenGL vendor string: VMware, Inc. OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 3.3, 256 bits) OpenGL version string: 2.1 Mesa 9.2.1 Not software rendered: no Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no Shows no 3D support. Can anyone please guide how to make things working again.

  Read the article

< Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >