Search Results

Search found 2589 results on 104 pages for 'dell powerconnect'.

Page 67/104 | < Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >

• Booting but not rebooting from external USB hard drive, what could be the problem?

  - by user8276

  I have a Dell Inspiron 6400 laptop with a dead internal hard drive controller. It boots perfectly from CD or USB. I therefore removed the internal hard drive and installed Ubuntu 10.10 Maverick onto an external USB hard drive. It boots and runs perfectly when doing a "cold start" of the PC. However, when I choose restart/reboot in the Ubuntu menu (e.g. after an update), I get this error message from the BIOS: "No bootable devices, strike f1 to retry boot, f2 for setup utility, press f5 to run onboard diagnostics". I can make the system boot again by pressing f2 or f5 and exiting the utility without having done anything. Or, I can simply power off the system and do a new "cold start". Does anyone know the likely reason for this problem and how to fix it. It is not a big issue but an annoyance that I would like to fix if possible.

  Read the article

• Flashing screen hovering over menubar on left side

  - by iwekb

  Just installed Ubuntu 10.10 netbook version on an older Dell Laptop (no other operating system installed). When hovering with mouse over menu bar, the full screen changes to default coloured back ground shortly and then back to normal (as after start-up) again. And that each time the mouse is over any of the (default) icons on the menu bar. I am not able to select any icon. No left or right click works on icons or anywhere on the menubar apart from the left top small icon, white Ubuntu logo, and the right top small icons for WiFi, sound, mail, shut-down etc. Those icons work. I tried re-installation again and all patches are downloaded. Same problem. Problem is that I can't enter commands either to reduce e.g. the swappiness (if that would be of any help). Can somebody help me that encountered similar problem or knows a resolution?

  Read the article

• How do I do a B43 Legacy install on Ubuntu 11.10?

  - by Gozzy

  I recently installed ubuntu onto an extra hard drive and everything booted correctly. However, my Linksys wireless card is not working. I went though all the forums and walk throughs and I know that I need to install the b43 legacy firmware to get the card to work. When I try to install the files, I keep getting the message in Terminal saying "No such file or directory" for every file i need to run. It's Ubuntu 11.10 on a dell optiplex gx280. Also, the "pool" file that is supposed to be on the file system is not there

  Read the article

• How do I get a Broadcom BCM4313 wireless card working?

  - by viky

  I upgraded Ubuntu from 11.10 to 12.04, until which wireless was working just fine. After the upgrade and reboot, wireless is not even being detected (When I click the network manager icon in the top panel, it does not show the wireless networks. Neither the Enable wireless option is there). But my laptop's LED indicator shows wireless is on. This is a Dell Vostro 3450 laptop with: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)** (from lspci). Is any other info needed? How do I get Wifi working?

  Read the article

• Is there a way to force lubuntu screen resolution?

  - by za1

  I have a Dell Inspiron 4000, 900 Mhz Pentium III, 192 MB RAM,10.1 GB disk running Lubuntu 12.04. When I start the computer, and I check the display resolution, Monitor Settings claims that the max resolution is 1024x768. I then connected another monitor I had lying around, rebooted, and now the laptop monitor looks normal,and monitor settings claims that 1280x1024 is the max resolution (it is) and the other monitor doesn't turn on. (black screen) The external monitor is not broken. Is there a way to, without the external monitor, force the laptop monitor resolution to 1280x1024? (The following is another question) - How can you run commands automatically at startup? Specifically "xinput 18 118 0" (without quotes) The first question is important, I can live with typing the second one at every boot. Thanks

  Read the article

• Ubuntu 10.10 booting but not rebooting from external USB hard drive, what could be the problem?

  - by user8276

  I have a Dell Inspiron 6400 laptop with a dead internal hard drive controller. It boots perfectly from CD or USB. I therefore removed the internal hard drive and installed Ubuntu 10.10 Maverick onto an external USB hard drive. It boots and runs perfectly when doing a "cold start" of the PC. However, when I choose restart/reboot in the Ubuntu menu (e.g. after an update), I get this error message from the BIOS: "No bootable devices, strike f1 to retry boot, f2 for setup utility, press f5 to run onboard diagnostics". I can make the system boot again by pressing f2 or f5 and exiting the utility without having done anything. Or, I can simply power off the system and do a new "cold start". Does anyone know the likely reason for this problem and how to fix it. It is not a big issue but an annoyance that I would like to fix if possible.

  Read the article

• Suggestions to Purchase a System76 Ubuntu Pre-Installed Laptop

  - by user2956795

  I am looking to buy a new laptop that well supports Ubuntu, and recently came across the Ubuntu laptop manufactured by System76. I am not familiar with this brand although it seems to me they produce Ubuntu laptop with good performance. The price listed on their website is also not that expensive as compared with a MacBook Pro, or ThinkPad T series, or the Dell XPS Developer Edition Has anyone used System76 Ubuntu Laptop? I'd like to ask for your opinions. How is the experience. Is it worth to put the money on?

  Read the article

• Why does installing 11.10 or 12.04 on old laptops fail?

  - by Adam

  I recently reimaged my Lenovo t400 with Ubuntu. However, after wiping two other systems (Compaq Presario 2100 and Dell Latitude D600) both hUbuntu 11.10 and Ubuntu 12.04 fail to load on boot. I am concerned that there is some type of issue using Ubuntu on these older systems as every part of the process has been repeated/attempted several times in the same manner as practiced in the successful load of the newer Lenovo t400. I now have two laptops without an operating system as the discs/thumb drives that were formatted to load on these devices do not seem to work. I would appreciate any assistance that you may be able to provide. Regards, -Adam

  Read the article

• How do I reset my display settings from the command line?

  - by Trevor

  I'm running 12.10 on a dell e5400 laptop and I used xrandr to get the dual monitors working that I connect through a laptop dock. I used xrandr again to switch back to the laptop display when I undocked. The problem is, after a restart, the laptop seems to want to come back up with the dual monitor configuration and the laptop screen stays blank. I can boot into single user mode but I'm not sure what to do from there to get the display settings reset. Any ideas? There's no xorg.conf file so I'm not sure where the settings are stored anymore. Thanks.

  Read the article

• How to force GNOME panels et. al. to display on a different monitor without mirroring?

  - by GrueKun

  So, I recently purchased a new 23" monitor for my PC. However, I can't use it with the PC currently as I am waiting on a replacement heatsink. In the mean time, I wanted to use it with my Dell laptop. I hooked it up to the VGA port, and it seems to be working properly. However, I wanted to know if there was a way I could move all of the main display elements over to the attached monitor? I wanted to shut the LCD panel off on the laptop and hook it up like a desktop. Relevant specs: Ubuntu 10.10 x64 Intel graphics chipset The attached monitor is currently set as the default monitor. Any suggestions are welcome. :)

  Read the article

• Trouble with Graphics Settings

  - by user291775

  I recently tried to install Ubuntu 14 Lts alongside Windows XP pro on my 2005 dell dimension E510. Everything appeared to be working correctly until I tried to log in, at which point it froze with a blank color background, which would flicker to black every other time I hit a key or clicked the mouse. I then tried booting in graphical safe mode at which point it told me that it could not configure the graphics settings. Does any body know what's going on. Thank you for any suggestions.

  Read the article

• Ubuntu samba file and print server

  - by Gerd

  I am using an old Dell desktop PC as a samba file and print server for a Windows 7 network. The version of Unbuntu I am running is 12.04 which seems to big for the RAM and disk space I have available. Unbuntu 12.04 runs very very slow, the printing over the home network works at a quite acceptable speed. I have two problems: SLOW Ubuntu and I cannot update samba. The update manager tells me "update failed". So my two questions: Is there anything I can remove from the standard 12.04 installation to make Ubuntu run faster and should I uninstall and the reinstall samba to overcome the "update failed" problem? I hesitate, as printing and file serving works somehow and I don't want to loose that. I know I should give you more information to give me answers. But what would you need to know? I am not a natural Linux user. Windows 7 is still my home. Thanks in advance, Gerd

  Read the article

• Logitech Wireless Keyboard & mouse not working aftesr upgrade to 12.04?

  - by deerjay99

  I upgraded my Dell Dimension 9200C to 12.04 Precise Pangolin with no issues, I ran it fine for a night but when I went back in a couple days later my Logitech Wireless Keyboard K350 and M510 mouse weren't active when booted. I can boot into an older version from the main the boot screen the mouse and keyboard work, but the network stack is gone. It says the networking manager on this version is not compatible. I'm scratching my head, it isn't the mouse and keyboard, they work fine on my dual boot, and they load fine in Knoppix. They did work fine on 12.04 for 1 night. Open to suggestions before I re-install completely.

  Read the article

• Broadcom wireless card disappears after restart

  - by user10854

  I used 'additional drivers' to install 'Broadcom STA wireless driver' and it returns an error. Within jockey.log it says the following numerous times. 2011-02-14 21:24:06,945 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted After it returns the error the network card will work temporarily until I restart the laptop. When I restart I got to go through the procedure again of trying to activate the driver, returns an error however it works temporarily. The network card is as follows on a Dell Inspiron 1545: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] Rev 01 I have been trying to solve this myself for many hours. Any help is appreciated/

  Read the article

• Edubuntu boot problem on dual boot PC

  - by trptplyr

  When booting Edubuntu on a dual boot PC with Windows 7, the last message that I get is "Restoring resolver state" [Ok]. I then press the Enter key, some other messages come up and go away too quickly to notice what they say, and then the system shuts down. Windows 7 works fine. My system is an older Dell Inspiron 9400 laptop with 3Gb usable memory. This all started happening after attempting to upgrade to the next version of Edubuntu, but was not allowed to because I didn't have enough space in my partition to allow for it. I'm unsure whether that has anything to do with the problem.

  Read the article

• How to use only intel graphics and power off radeon?

  - by luizrogeriocn

  I've been using Linux for quite a while in everyday computing and programming. But now i got this new laptop with amazing battery life on windows which runs pretty cool even while gaming. But for some reason on Ubuntu I get like 1/3 battery life and it gets hot even while browsing the web. I have the proprietary drivers for radeon, but I'm thinking about upgrading from Ubuntu 12.04 to 14.04, and I would like to know how can I use only the Intel graphics and have radeon always turned off? Since I do not need the discrete graphics on Ubuntu and I'm pretty sure my problem is related to the radeon sucking up my battery and generating heat. My laptop technical specifications are: Dell latitude 3540 Intel core i7 4500U (with Intel hd4400 graphics ) Ati Radeon HD 8850m with 2GB GDDR5 VRAM 8 GB DDR3L @1600mhz Toshiba 256gb SSD Ubuntu 12.4.3 If you need any additional info, please tell me :)

  Read the article

• Time display and Cursor bug in Ubuntu 14.04 LTS

  - by user291774

  Just installed Ubuntu 14.04. Noticed the time in seconds speeds up then slows down to normal speed. The cursor for the keyboard has a strange rhythm; it stays normal, then slowly speeds up faster and faster till it looks like it's not blinking anymore, then goes back to normal and starts the process again. It almost seems like my whole operating system speeds up then slows down again. Even the hour circle that spins when it's loading starts slowly then it picks up speed till it spins so fast it looks like it's not even spinning. It interferes with video and the whole system. I have a Dell Vostro 3750 dual video cards and dual boot with Windows 7. Windows is running fine.

  Read the article

• Keyboard Issues After Resuming From Sleep

  - by sammyd253

  I'm using Ubuntu 11.10 x64. It's running on my Dell Vostro V13. Everything works great until I shut the lid of my laptop (puts laptop into sleep). Once I come back and resume working in Ubuntu, typing becomes a chore. Ubuntu misses a lot of the keypresses from my keyboard. It usually results in me mashing my keyboard until the letter appears. A full system reboot fixes the problem. Again, typing is never an issue unless I resume from sleep. Any ideas?

  Read the article

• Wi-Fi connections gets Idle

  - by marcocamejo

  I am having this terrible problem. I have read a lot of people getting disconnected from the Network, it is not my case, I don't get disconnected, the connection just gets "idle" most of the time. It only works for short periods of time (seconds, a couple of minutes at most), then gets dead, then works again, and so on. It is annoying. I am using Ubuntu 11.10 on a Dell M5030 laptop. I have Windows 7 installed too, and of course with it, the wifi works perfectly. Any idea? advice?

  Read the article

• Moving a LAMP set up from 32 bit to 64 bit

  - by user10157

  Hello everyone... I have setup an Ubuntu server 10.10 32bit on an old Dell D610 Laptop for testing. I have the latest PHP, MySQL and Apache with Wordpress installed. After the testing is over and once I finish adding material to my wordpress I will build a Ubuntu 10.10 64bit VM on Hyper-V. What I am wondering is , if it's best practice to build everything from scratch (which will take me more time and would like to avoid) or transfer the database and all other settings? If I choose to transfer how and what I need to do? Here's where I'd like some help as I am still an intermediate admin (If I can call it that!) I am looking forward for your help. Thanks!

  Read the article

• Very slow startup after update to 12.04

  - by M Legoh

  My hardware: Dell Latitude D600 laptop Processor: Intel Pentium (r) 1.8 GHz Memory 1.2 GiB Graphics R200 (RV250 4C66) x86/MMX/SSE2 TCL DRI2 Disk: 37.7 gb I did an update from 11.?? using the automatic system update that pops up when you switch/log on. Ever since then when I switch on the machine it takes approximately one hour to get to the login screen. Sometimes the actual login will take time too, but sometimes within a couple of minutes I am logged in. Once I am logged in I find I can work normally, the response is not swift, but is neither too slow that I cannot work. I was wondering if there was anything I could do to speed things up. I deliberately did not do a clean install from disk, because I did not want to loose settings on the machine.

  Read the article

• bootscreen downscaled

  - by blackmist

  my specs intel mb dh67cl corsair 4gb ram nvidia 560ti gtx i5 processor dell 22" monitor 1920x1080 firstly, i began using ubuntu last year. now im in love with it. just one minor detail i dont like is that the bootscreen changed just after the first boot. now im using 12.04.1. i will explain how it happened. first i installed ubuntu via windows. so it booted for the first time and life was beautiful. the resolution was 1920x1080. then i installed the nvidia drivers, all the updates and codecs for the medias. now the ubuntu bootscreen downscaled to a lower resolution. i tried searching for answers, but nothing was for ubuntu 12.04.1. since im a newbie, i didnt want to take any chances. i need help. i like the bootscreen.

  Read the article

• Mouse on screen lags

  - by Jeggy

  I just made a fresh install of Ubuntu 13.10 64bit on my Dell XPS 15 laptop. My mouse lags/glitches/blinks each time something is loading in Ubuntu. when a youtube video is playing in the background it blinks all the time, and it also blinks for each character that I write, it's very annoying. It also blinks for each time the Blinking Cursor in a text field blinks. When I have just booted up my laptop it can be away for a second or more (than after it comes back it goes away for a second or more and this happends for awhile), so I have no chance of seeing the mouse on my screen.

  Read the article

• Ubuntu on low powered laptop

  - by zkent

  First off, I am new to Ubuntu. I come from a Windows background (DOS before that) and am loving it so far. I installed it on an older Dell laptop that I wanted to get another year out of. I set this machine up primarily as a LAMP development machine for a project I am working on. The machine is a Vostro 1500 and it has 4GB RAM (maxed) and an upgraded hard drive. I can't watch YouTube videos for long before it starts to overheat and start acting sporadic. I can live without YouTube but every so often the application switching (alt-tab) gets slower and begins not showing all applications and the Dash home quits displaying properly. I am sure I am asking a lot of this old machine. What I really want to know is: are there any settings in Ubuntu that allow me to lower the graphic effects (fade-ins, transparencies, fancy transitions, etc) that would be less taxing on the video card?

  Read the article

• How do I install drivers for graphics and sound?

  - by Sid

  I recently shifted to Ubuntu 12.04 from windows 7. I completely removed Windows and then installed Ubuntu. However, I can't find a way to download and install drivers for my video and audio hardware like I used to be able to do in Windows. Could someone please explain to me how software and drivers, in general, are installed on Ubuntu. Is installing through 'Ubuntu Software Center' the only way to install them? My laptop model is: Dell Inspiron 14 N4010 (i5/4gb/500gb). Kindly help. Thanks in advance.

  Read the article

< Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >