Search Results

Search found 12371 results on 495 pages for 'ok'.

Page 67/495 | < Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >

• Debian software raid 1: boot from both disk

  - by bsreekanth

  I newly installed debian squeeze with software raid.The way I did was, as also given in this thread. I have 2 HDD with 500 GB each. For each of them, I created 3 partitions (/boot, / and swap) I selected the hard drive and created a new partition table I created a new partition that was 1GB. I then specified to use the partition as a Physical Volume for RAID. and used for /boot and enabled bootable. Created another partition, which is of 480 GB, and then specified to use the partition as a Physical Volume for RAID. and used for /. Created another partion and used for swap Then RAID configuration: Through Configure RAID menu - create MD device - (2 for the number of drives, 0 for spare devices) Next select the partitions you want to be members of /dev/MD0. I selected /dev/sda1 and /dev/sdb1 (for /boot) Next select the partitions you want to be members of /dev/MD1. I selected /dev/sda6 and /dev/sdb6 (for /) And no RAID for swap partitions 'Finish Partitioning and write changes to disk' -- Finish the rest of the install like normal Everything is ok now, except I am not sure how to test my raid config. When I pull the power of the HDD, it only boots from one disk. I read in some forum that I may have to install GRUB manually on the other. In Debian Squeeze, there is no grub command. Not sure how to make my software raid bootable from both disk. Also, please comment on my steps above. Anything unusual. I configured /boot partitions of both disks to be boot=yes. Not sure whether that is ok. Thanks, Bsr

  Read the article

• How can I safely close this window and forever avoid seeing similar pop-ups from Mackeeper Zeobit's malware and spyware?

  - by Michael Prescott

  The attached image shows a window that just popped up and the only button available is the OK button. I could Force quit Safari, but I've got several sites open right now and don't want to try and find my place again. Besides, I've seen similar hacks in the past and I'd like to learn how to handle them in a way better than just a brute force-quit. I've never heard of MacKeeper or Zeobit, so I opened Firefox and did a few searches while Safari is obviously still stuck, waiting for me to click the sneaky OK button in the dialog window. Anyhow, at least the first few pages of most search results contain lots of blabbering from questionable witnesses about how MacKeeper saved them from some malware or spyware. However, any company that is hacking the browser to maliciously install their product is itself the criminal and not providing a true security application. So, there are three questions here: How can I close this window? Can I do something to Safari to avoid these hacks in the future? (Just curious) Is MacKeeper or Zeobit somehow loading the search results so that no information about their application being malware or spyware is listed (I can't be the only person in the world that is offended by their tactics, even though it appears I am)?

  Read the article

• Accounting setup in freeradius with mikrotik and the "always" module

  - by Matt

  I have a freeradius setup that is being used to provide authentication for users on a wireless network. The access points are all Mikrotik hardware and the users are connected 24/7. We've been using Daloradius with mysql and freeradius 2. The boss wants to use the accounting information and while this is all set up and appears to be working, I've found that not all the accounting information is present. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly. So he started poking around at this link: http://wiki.mikrotik.com/wiki/RouterOs_MySql_Freeradius#Configuring_RouterOs_for_Radius_.26_PPP.2A_AAA And was looking specifically at the following section. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly always fail { rcode = fail } always reject { rcode = reject } always ok { rcode = ok simulcount = 0 mpp = no } However, that link references freeradius 1 and I can't find this in the radius.conf file for freeradius 2. What does it do and could it be a reason I'm missing data? EDIT: I have found one issue. We have a backup freeradius server that is also receiving the accounting packets. Although they are replicating, it's only a master/slave configuration. If the slave receives accounting packets it won't replicate them back to the master. Although I suspect this might solve it, the boss is not convinced due to the always module. Is there anything special I need to configure in the mikrotik AP's or freeradius 2 for clients connected 24/7.

  Read the article

• litespeed issue with content-type

  - by sandeep.s85

  I am running magento with litespeed. The problem I am facing is that ajax call is being made of which header is set as x-json, but lightspeed is setting another header of text/html content type I've checked that page with apache and everything is working fine. I checked the response headers with apache and litespeed and here are they: With apache: HTTP/1.1 200 OK Date: Fri, 07 Sep 2012 05:58:47 GMT Server: Apache Expires: Thu, 19 Nov 1981 08:52:00 GMT Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 Pragma: no-cache Set-Cookie: frontend=164b21c64808a05e806027bdbd4d745d; expires=Fri, 07-Sep-2012 06:58:48 GMT; path=/; domain=mydomain.com; httponly Connection: close Transfer-Encoding: chunked Content-Type: application/x-json With litespeed: HTTP/1.1 200 OK Date: Fri, 07 Sep 2012 06:10:55 GMT Server: LiteSpeed Connection: close Expires: Thu, 19 Nov 1981 08:52:00 GMT Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 Pragma: no-cache Set-Cookie: frontend=164b21c64808a05e806027bdbd4d745d; expires=Fri, 07-Sep-2012 07:10:55 GMT; path=/; domain=mydomain.com; httponly Content-Type: text/html; charset=UTF-8 Content-Length: 474 Vary: User-Agent I've also added application/json to mime.properties of litespeed,restarted it but that did not work. Here is the screenshot

  Read the article

• Make isolinux 4.0.3 chainload itself in VMWare

  - by chainloader

  I have a bootable iso which boots into isolinux 4.0.3 and I want to make it chainload itself (my actual goal is to chainload isolinux.bin v4.0.1-debian, which should start up the Ubuntu10.10 Live CD, but for now I just want to make it chainload itself). I can't get isolinux to chainload any isolinux.bin, no matter what version. It either freezes or shows a "checksum error" message. I'm using VMWare to test the iso. Things I have tried: .com32 /boot/isolinux/chain.c32 /boot/isolinux/isolinux-debug.bin (chainload self) this shows Loading the boot file... Booting... ISOLINUX 4.03 2010-10-22 Copyright (C) 1994-2010 H. Peter Anvin et al isolinux: Starting up, DL = 9F isolinux: Loaded spec packet OK, drive = 9F isolinux: Main image LBA = 53F00100 ...and the machine freezes. Then I've tried this (chainload GRUB4DOS 0.4.5b) chainloader /boot/isolinux/isolinux-debug.bin Result: Error 13: Invalid or unsupported executable format Next try: (chainload GRUB4DOS 0.4.5b) chainloader --force /boot/isolinux/isolinux-debug.bin boot Result: ISOLINUX 4.03 2010-10-22 Copyright (C) 1994-2010 H. Peter Anvin et al isolinux: Starting up, DL = 9F isolinux: Loaded spec packet OK, drive = 9F isolinux: No boot info table, assuming single session disk... isolinux: Spec packet missing LBA information, trying to wing it... isolinux: Main image LBA = 00000686 isolinux: Image checksum error, sorry... Boot failed: press a key to retry... I have tried other things, but all of them failed miserably. Any suggestions?

  Read the article

• Batch Script to Find Certain words and delete those lines in a file

  - by SuperUserMan

  EDITED THE QUESTION as regarding type of solutions I am on Windows & some suggested SED etc. So i am OK with these 3rd party standalone exe's using command line Say i have following lines in abc.txt file "@yuy007 what are you doing friend #disneyrocks" "STFU, i dont care what you think @happy55" "@social88 @gg99 ok mate see you at the subway :)" "btw arnold was great in that movie @tt11 @gg11 #disneyrocks" "we are going to disney. Do you want to? #disneyrocks" "We dont like disney.#disneyrocks we are not going" ".@socialguy what are you upto #disneyrocks " I need to employ 5 filters with above file to get def.txt Delete all lines which start with @ character, like 1st and 3rd Delete all lines which start with .@ characters, like 7th Delete all lines which don't have any word starting with # like 2nd and 3rd In leftover lines, Delete all words starting with @ character (keeping the lines intact) like words @happy55 in 2nd , @social99 & @gg99 in 3rd, etc. In this case we still need to preserve quotes " at start and end of line Delete all the blank lines left after above lines are removed EDIT if i have following line , it wrongly deletes the content after @word's "btw arnold was great in that movie @tt101 @gb1997 #whatthehell" is edited to "btw arnold was great in that movie" Thanks

  Read the article

• DD-WRT (WRT54G) and (THOMSON TG782) how to put them togather?

  - by FeRtoll

  Ok so let me explain, i bought WRT54G and successfully installed DD-WRT v24-sp1 (07/26/08) mini-special - build 9994. That's all ok no problems with it all normal functioning. And just to add (i don't need wireless, wireless is turned off always) What i want: ISP's router (TG782) from it's INTERNET port(out) cable "which was before in my pc" is connected to WRT54G's INTERNET port and then from WRT54G LAN port 1 to my pc. The problem: How do i connect and setup all? I have tried many times on many different ways but cant get it to work IF THE CABLE FROM TG782 IS CONNECTED TO WRT54G ON INTERNET PORT. If i connect the TG782 to Lan port 1 on WRT54G and my pc to lan port 2 then all works fine after i setup gateway and all. But i want to connect TG782 to Internet port of WRT54G because i need "Access Restrictions" and this only goes through WAN right? please correct me if i am wrong. What i have tried: This is how i have tried to setup all. The TG782 router ip is 192.168.1.1 And WRT54G ip is 192.168.1.30 so in WRT54G control panel i have setup like this: ----WAN Connection Type---- Connection Type: Automatic Configuration - DHCP STP: Disabled ----Router IP---- Local IP Address: 192.168.1.30 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 (the TG782) ----Network Address Server Settings (DHCP)---- DHCP Type: DHCP Server Start IP Address: 192.168.1.100 Maximum DHCP Users: 6 And this wont work i probably miss something more, if anyone can help i would be thankfull. Also i have to note that i have tried to set my network adapter on pc to use the gateway of WRT54G and ip 192.168.1.102 In short: i cant get it to work normal only as a switch! Thanks for any help! -------EDIT:------- Here is an image which maybe can help: http://img27.imageshack.us/img27/4227/allin1w.jpg

  Read the article

• Windows XP laptop doesn't appear in WSUS All computers list

  - by George

  I have this one laptop that doesn't appear in WSUS all computers list. We have about 23-25 PCs/laptops/servers in the network, all, but one are listed in WSUS. This is what I have done so far: 1) Changing Updates on local PC: Go to your Windows XP client and start a new Microsoft Management Console (MMC). At Start, Run, type MMC. Use Ctrl+M to add a new snap-in. Click Add, and then add the Group Policy Object Editor for the Local Computer. Click Close, and then click OK. Expand the Local Computer Policy. Under Computer Configuration, go to Administrative Templates, Windows Components, Windows Update. In the right-hand pane, double-click Specify intranet Microsoft update service location. Configure the settings to reflect my WSUS server. Click OK and then close the MMC without saving it. executed wuauclt.exe /detectnow 2) Edited registry key to be pushed to the PCs using GPO [HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\WindowsUpdate] "WUServer"=http://wsusserver "TargetGroupEnabled"=dword:00000001 "TargetGroup"="WINXP" "WUStatusServer"=http://wsuswerver 3) executed wuauclt /resetauthorization /detectnow 4)Synchronised and refreshed the group I am running out of ideas here. The client is running Windows XP pro, WSUS version is 3.0 and is running on Windows 2008 R2 64-bit. Please, help! Thanks! EDIT 13.IX.2012 @ 15.40 I should have also mentioned that we do have a Windows Update GPO for workstations group and that laptop is a part of that group.

  Read the article

• Why can't I specify the executable that opens file with extension on windows?

  - by Glen S. Dalton

  I am on windows server 2003, but I guess it is the same on windows xp. This is a superuser question, because it is definitly desktop, so do not move or close it. Question: I copied some movable applications (usually people create them for usb sticks) to locations like c:\bin\app1\app1.exe app1.exe can open files of type *.ap1 When I rightclick file.ap1 and choose "open with ..." the "Open with" dialog appears. But it is not working how I expect in this situation. I can choose c:\bin\app1\app1.exe with the "Browse" button, but: app1.exe will not appear in the dialog where I just choosed it in the programs list, like I am used to it after clicking OK on it in the browse dialog. app1.exe will not open it when I click ok in the "Open with" dialog, the application that was assigned until then will still open it What could be the reason? Edit: Additional Information: my account is member of the administrators group I just changed the permissions of the folder c:\bin\app1\ and made sure that the group "Administrators" has all rights. I also inherited this manually to all subfodlers and subfiles.

  Read the article

• The RTL8111/8168B NIC under Linux and the r8168 driver

  - by nik

  So I've got one of the infamous R8168 Realtek ethernet NIC, which have some problems under Linux. After some research, I found out I had to use the r8168 driver for this card (and not the r8169 which still loads when nothing else is available), which I did. So now everything works fine... Sort of. My download and upload rates are more than halved compared to what I should get. When I test (with eg. speedtest) I get something like 20M (often 15M) in download and 30M in upload, but if I test under Windows (everything is otherwise identical: same ethernet cable, same connection, at the same time of the day (well 5 min apart)...), I get 50M upload/download (which is what I expect). Where can it come from? Here's some info: ~ # lspci [...] 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) ~ # modinfo r8168 filename: /lib/modules/3.2.1-gentoo-r2/net/r8168.ko version: 8.027.00-NAPI license: GPL description: RealTek RTL-8168 Gigabit Ethernet driver author: Realtek and the Linux r8168 crew <[email protected]> srcversion: 0A6E9F1D4E8E51DE4B6BEE3 alias: pci:v00001186d00004300sv00001186sd00004B10bc*sc*i* alias: pci:v000010ECd00008168sv*sd*bc*sc*i* depends: vermagic: 3.2.1-gentoo-r2 SMP mod_unload [...] ~ # mii-tool -v eth0: negotiated 100baseTx-HD, link ok product info: vendor 00:07:32, model 17 rev 4 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

  Read the article

• Bad network performance on KVM guest

  - by Devator

  I have a dedicated server connected to a 1000 Mbit port. However, the Debian guest is only getting half to a 1/4 the speeds: On the node itself (Linux node 2.6.32-279.9.1.el6.x86_64 #1 SMP Tue Sep 25 21:43:11 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux): wget http://www.bbned.nl/scripts/speedtest/download/file1000mb.bin -O /dev/null --2012-11-11 23:10:11-- http://www.bbned.nl/scripts/speedtest/download/file1000mb.bin Resolving www.bbned.nl... 62.177.144.181 Connecting to www.bbned.nl|62.177.144.181|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1048576000 (1000M) [application/octet-stream] Saving to: â/dev/nullâ 100%[====================================>] 1,048,576,000 100M/s in 10s 2012-11-11 23:10:21 (100 MB/s) - â/dev/nullâ On the guest (Debian 6.0.5, x64: Linux debian 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux): wget http://www.bbned.nl/scripts/speedtest/download/file1000mb.bin -O /dev/null --2012-11-11 23:10:41-- http://www.bbned.nl/scripts/speedtest/download/file1000mb.bin Resolving www.bbned.nl... 62.177.144.181 Connecting to www.bbned.nl|62.177.144.181|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1048576000 (1000M) [application/octet-stream] Saving to: â/dev/nullâ 100%[=================================================================================================================================================================================================>] 1,048,576,000 16.5M/s in 42s 2012-11-11 23:11:23 (23.8 MB/s) - â/dev/nullâ I use the virtio NIC. I tried some more NICs: e1000 and the Realtek 8139 but those yield even worse results. Anyone has an idea how to improve these speeds?

  Read the article

• Windows 7: Setting up backup to an external hard drive on another computer on the network

  - by seansand

  I have an external hard drive connected to a Windows 7 (Home Edition) computer. I have another computer (with Windows 7 Ultimate), and I want to have the Windows 7 Ultimate back up to the same external hard drive, without having to disconnect and move the external hard drive from the Home Edition PC. When I get to the "Set up backup" dialog within Windows 7, it asks me where to save the backup. I select "Save on a network". However, when I enter "\\computername\harddrivename" under Browse, the "OK" button remains grayed out. The button remains grayed out unless I also enter a Username and Password under "Network credentials". However, the account I have on the other computer doesn't have a password for it. To un-gray out the button I must enter a fake password, allowing me to click "OK", but then obviously I get a "bad password" error. Does anyone know how to get around this problem? (Seems kind of ridiculous.) I made sure that the security settings with the external hard drive on the other computer are full access to Everyone, so permissions is not the problem. I also thought about using Homegroup instead of the regular security settings, but there is no obvious way to go about it that way, either.

  Read the article

• Accounting setup in freeradius with mikrotik and the "always" module

  - by Matt

  I have a freeradius setup that is being used to provide authentication for users on a wireless network. The access points are all Mikrotik hardware and the users are connected 24/7. We've been using Daloradius with mysql and freeradius 2. The boss wants to use the accounting information and while this is all set up and appears to be working, I've found that not all the accounting information is present. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly. So he started poking around at this link: http://wiki.mikrotik.com/wiki/RouterOs_MySql_Freeradius#Configuring_RouterOs_for_Radius_.26_PPP.2A_AAA And was looking specifically at the following section. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly always fail { rcode = fail } always reject { rcode = reject } always ok { rcode = ok simulcount = 0 mpp = no } However, that link references freeradius 1 and I can't find this in the radius.conf file for freeradius 2. What does it do and could it be a reason I'm missing data? EDIT: I have found one issue. We have a backup freeradius server that is also receiving the accounting packets. Although they are replicating, it's only a master/slave configuration. If the slave receives accounting packets it won't replicate them back to the master. Although I suspect this might solve it, the boss is not convinced due to the always module. Is there anything special I need to configure in the mikrotik AP's or freeradius 2 for clients connected 24/7.

  Read the article

• Asterisk terminating outbound call when picked up, sends 'BYE' message

  - by vo

  I'm running Asterisk 1.6.1.10 / FreePBX 2.5.2.2 and I've got an outbound trunk setup. Everything use to work fine until recently (perhaps due to upgrade to FC12 or other things I'm not sure). Anyway the setup does not appear to have issues registering and setting up the call, RTP packets go both ways and you can hear the ringing from the other side. However it appears that when the call is picked up or thereabouts, the incoming RTP packets cease. Upon closer inspection with Wireshark, there are these particular packets that seem to be the cause: trunk->asterisk SIP/SD Status: 200 OK, with session description asterisk->trunk SIP Request: ACK sip:<phone>@trunk:6889 asterisk->trunk SIP Request: BYE sip:<phone>@trunk:6889 [..about a dozzen RTP packets in/outbound..] trunk->asterisk SIP Status: 200 OK, CSeq: 104 Bye [..outbound RTP continues, phone is silent..] Then the inbound RTP packets cease, however the asterisk logs dont show any activity at this point. The last entry reads 'SIP/ is answered SIP/'. Then when you hangup the extension, you get asterisk->trunk SIP Request: BYE sip:<phone>@trunk:6889 trunk->asterisk SIP Status: 481 Call Leg/Transaction does not exist My trunk peer settings in FreePBX are: username=<user> fromuser=<user> canreinvite=no type=friend secret=<pass> qualify=no [qualify yes produces 401/forbidden messages] nat=yes insecure=very host=<sip trunk gateway> fromdomain=<sip trunk gateway> disallow=all context=from-pstn allow=ulaw dtmfmode=inband Under sip_general_custom.conf i have stunaddr=stun.xten.com externrefresh=120 localnet=192.168.1.1/255.255.255.0 nat=yes Whats causing Asterisk to prematurely end the call and still think the call is in progress? I have no idea where to look next.

  Read the article

• 550 Requested action not taken: mailbox unavailable

  - by Porch

  I setup a small box with Server 2003 64bit to be used as a webserver and email server for a small school. Real simple stuff for a few users. A simple website and a handful of emails. rDNS and spf records setup and pass every test I found including test at dnsstuff.com. Email sending to almost every email address (google, hotmail, aol, whatever) works. However, with one domain, I get an bounce back with the error. 550 Requested action not taken: mailbox unavailable It's another school running Exchange judging from some packet sniffing with WireShark. Every email on this domain I have tried sending to gives this error. The email address is valid as I can send to it from my personal, and gmail account without a problem. Does anyone know of some anti-spam software that gives an 550 error like the above? What else could this be? Thanks for any suggestions. Packet capture of the two servers communicating look like this. 220 <server snip> Microsoft ESMTP MAIL Service, Version: 6.0.3790.3959 ready at Sat, 2 Oct 2010 12:48:17 -0700 EHLO <email snip> 250-<server snip> Hello [<ip snip>] 250-TURN 250-SIZE 250-ETRN 250-XXXXXXXXXX 250-DSN 250-ENHANCEDSTATUSCODES 250-8bitmime 250-BINARYMIME 250-XXXXXXXX 250-VRFY 250-X-EXPS GSSAPI NTLM LOGIN 250-X-EXPS=LOGIN 250-AUTH GSSAPI NTLM LOGIN 250-AUTH=LOGIN 250-X-LINK2STATE 250-XXXXXXX 250 OK MAIL FROM: <email snip> 250 2.1.0 <email snip>....Sender OK RCPT TO:<email snip> 250 2.1.5 <email snip> DATA 354 Start mail input; end with <CRLF>.<CRLF> <email body here> . 550 Requested action not taken: mailbox unavailable QUIT 221 Goodbye

  Read the article

• Recovering a damaged microSDHC

  - by djechelon

  I just bought from eBay a Kingston 32GB microSDHC that was advertised as defective. The seller said that there could be formatting problems or with transfer of large files. Unfortunately, when I got it, it was a total mess. My Nikon camera doesn't read it at all (OK, maybe it doesn't support 32GB) My Linux laptop doesn't mount it: can't read superblock The same laptop refuses to mkfs.msdos because it failed whilst writing reserved sector The same laptop, under Windows, doesn't read nor format the card HTC HD2 mounts the MMC, allows me to write via USB, but is unable to open the just written files OK, folks, now you would say I would have to go through Paypal complaint... that's not that easy. I consciously bought a half-price card that was known to show some defects, and Paypal complaints take time. Obviously, I can't accept somebody sold me a completely use-less computer decoration. So I'll keep it as last option. My question is Do you know a way, under either Linux or Windows, to thoroughly scan, test and possibly repair memory cards, even if I have to lose some percentage of space because of bad sectors? If I can keep at least half of the card intact it would certainly be fine. I used to do broken sector marking with hard disks in the past. I almost forgot: MONSTR:/home/djechelon # fsck /dev/mmcblk0p1 fsck from util-linux-ng 2.17.2 dosfsck 3.0.9, 31 Jan 2010, FAT32, LFN Read 512 bytes at 0:Input/output error

  Read the article

• Installing mod_pagespeed (Apache module) on CentOS

  - by Sid B

  I have a CentOS (5.7 Final) system on which I already have Apache (2.2.3) installed. I have installed mod_pagespeed by following the instructions on: http://code.google.com/speed/page-speed/download.html and got the following while installing: # rpm -U mod-pagespeed-*.rpm warning: mod-pagespeed-beta_current_x86_64.rpm: Header V4 DSA signature: NOKEY, key ID 7fac5991 [ OK ] atd: [ OK ] It does appear to be installed properly: # apachectl -t -D DUMP_MODULES Loaded Modules: ... pagespeed_module (shared) And I've made the following changes in /etc/httpd/conf.d/pagespeed.conf Added: ModPagespeedEnableFilters collapse_whitespace,elide_attributes ModPagespeedEnableFilters combine_css,rewrite_css,move_css_to_head,inline_css ModPagespeedEnableFilters rewrite_javascript,inline_javascript ModPagespeedEnableFilters rewrite_images,insert_img_dimensions ModPagespeedEnableFilters extend_cache ModPagespeedEnableFilters remove_quotes,remove_comments ModPagespeedEnableFilters add_instrumentation Commented out the following lines in mod_pagespeed_statistics <Location /mod_pagespeed_statistics> **# Order allow,deny** # You may insert other "Allow from" lines to add hosts you want to # allow to look at generated statistics. Another possibility is # to comment out the "Order" and "Allow" options from the config # file, to allow any client that can reach your server to examine # statistics. This might be appropriate in an experimental setup or # if the Apache server is protected by a reverse proxy that will # filter URLs in some fashion. **# Allow from localhost** **# Allow from 127.0.0.1** SetHandler mod_pagespeed_statistics </Location> As a separate note, I'm trying to run the prescribed system tests as specified on google's site, but it gives the following error. I'm averse to updating wget on my server, as I'm sure there's no need for it for the actual module to function correctly. ./system_test.sh www.domain.com You have the wrong version of wget. 1.12 is required.

  Read the article

• Restricting memory area for linux kernel

  - by user1066789

  I am running ltib linux on P1022RDK (P1022 Core) platform. I have 512 MB = 0x20000000 memory. I want my linux kernel to use second half of the board memory (i.e from 256 MB to 512 MB) and want first half of memory to be reserved for some other purpose. For this I am building linux kernel using ltib. For that purpose I am setting following kernel configuration. Please suggest if I am doing it the right way. CONFIG_LOWMEM_SIZE = 0x10000000 # 256 MB CONFIG_PHYSICAL_START = 0x10000000 # Starting from 256MB (second half of memory) On the Uboot I am loading the kernel as following way setenv loadaddr 0x11000000 # Kernel base = 0x10000000 + 0x01000000 (offset) setenv fdtaddr 0x10c00000 # Kernel base = 0x10000000 + 0x00c00000 (offset) bootm $loadaddr - $fdtaddr My kernel Load address is 0x10000000 & kernel entry point is 0x10000000 Doing above configuration / steps my kernel stuck at following on Uboot ## Booting kernel from Legacy Image at 11000000 ... Image Name: Linux-2.6.32.13 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 3352851 Bytes = 3.2 MB Load Address: 10000000 Entry Point: 10000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 10c00000 Booting using the fdt blob at 0x10c00000 Uncompressing Kernel Image ... OK ================ >> It should uncompress FDT here & continue ============== Any thoughts ?

  Read the article

• Restricting memory area for linux kernel

  - by user1066789

  I am running ltib linux on P1022RDK (P1022 Core) platform. I have 512 MB = 0x20000000 memory. I want my linux kernel to use second half of the board memory (i.e from 256 MB to 512 MB) and want first half of memory to be reserved for some other purpose. For this I am building linux kernel using ltib. For that purpose I am setting following kernel configuration. Please suggest if I am doing it the right way. CONFIG_LOWMEM_SIZE = 0x10000000 # 256 MB CONFIG_PHYSICAL_START = 0x10000000 # Starting from 256MB (second half of memory) On the Uboot I am loading the kernel as following way setenv loadaddr 0x11000000 # Kernel base = 0x10000000 + 0x01000000 (offset) setenv fdtaddr 0x10c00000 # Kernel base = 0x10000000 + 0x00c00000 (offset) bootm $loadaddr - $fdtaddr My kernel Load address is 0x10000000 & kernel entry point is 0x10000000 Doing above configuration / steps my kernel stuck at following on Uboot ## Booting kernel from Legacy Image at 11000000 ... Image Name: Linux-2.6.32.13 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 3352851 Bytes = 3.2 MB Load Address: 10000000 Entry Point: 10000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 10c00000 Booting using the fdt blob at 0x10c00000 Uncompressing Kernel Image ... OK ================ It should uncompress FDT here & continue ============== Any thoughts ?

  Read the article

• HTTP responses curl and wget different results

  - by Fab

  To check HTTP response header for a set of urls I send with curl the following request headers foreach ( $urls as $url ) { // Setup headers - I used the same headers from Firefox version 2.0.0.6 $header[ ] = "Accept: text/xml,application/xml,application/xhtml+xml,"; $header[ ] = "text/html;q=0.9,text/plain;q=0.8,image/png,*/*;q=0.5"; $header[ ] = "Cache-Control: max-age=0"; $header[ ] = "Connection: keep-alive"; $header[ ] = "Keep-Alive: 300"; $header[ ] = "Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7"; $header[ ] = "Accept-Language: en-us,en;q=0.5"; $header[ ] = "Pragma: "; // browsers keep this blank. curl_setopt( $ch, CURLOPT_URL, $url ); curl_setopt( $ch, CURLOPT_USERAGENT, 'Googlebot/2.1 (+http://www.google.com/bot.html)'); curl_setopt( $ch, CURLOPT_HTTPHEADER, $header); curl_setopt( $ch, CURLOPT_REFERER, 'http://www.google.com'); curl_setopt( $ch, CURLOPT_HEADER, true ); curl_setopt( $ch, CURLOPT_NOBODY, true ); curl_setopt( $ch, CURLOPT_RETURNTRANSFER, true ); curl_setopt( $ch, CURLOPT_FOLLOWLOCATION, true ); curl_setopt( $ch, CURLOPT_HTTPAUTH, CURLAUTH_ANY ); curl_setopt( $ch, CURLOPT_TIMEOUT, 10 ); //timeout 10 seconds } Sometimes I receive 200 OK which is good other time 301, 302, 307 which I consider good as well, but other times I receive weird status as 406, 500, 504 which should identify an invalid url but when I open it on the browser they are fine for example the script returns http://www.awe.co.uk/ => HTTP/1.1 406 Not Acceptable and wget returns wget http://www.awe.co.uk/ --2011-06-23 15:26:26-- http://www.awe.co.uk/ Resolving www.awe.co.uk... 77.73.123.140 Connecting to www.awe.co.uk|77.73.123.140|:80... connected. HTTP request sent, awaiting response... 200 OK Does anyone know which request header I am missing or adding in excess?

  Read the article

• check_snmp warning & critical thresholds with negative values

  - by Oesor

  I'm querying some signal level values measured in dBm, and the SNMP host on the remove device reports the values as negative values, ie, -90 dBm. However, check-snmp seems to be incapable of dealing with negative numbers as part of its threshold values. If I specify the values as part of a collection of OIDs, it accepts the syntax but converts the snmp value to positive, thus always generating a WARNING/CRITICAL result: root@ops-00:/usr/local/nagios/libexec# ./check_snmp -H 192.168.1.100 -o DEVICE-MIB::AverageReceiveSNR.0,DEVICE-MIB::CurrentNoiseFloor.0 -w 10:,~:-85 -c 15:,~:-80 -vvvv /usr/bin/snmpget -t 1 -r 5 -m ALL -v 1 [authpriv] 192.168.1.100:161 DEVICE-MIB::AverageReceiveSNR.0 DEVICE-MIB::CurrentNoiseFloor.0 DEVICE-MIB::AverageReceiveSNR.0 = INTEGER: 25 DEVICE-MIB::CurrentNoiseFloor.0 = INTEGER: -97 Processing line 1 oidname: DEVICE-MIB::AverageReceiveSNR.0 response: = INTEGER: 25 Processing line 2 oidname: DEVICE-MIB::CurrentNoiseFloor.0 response: = INTEGER: -97 SNMP CRITICAL - 25 *97* | DEVICE-MIB::AverageReceiveSNR.0=25 DEVICE-MIB::CurrentNoiseFloor.0=97 If I run it with a single OID, it gives me an error that the format is incorrect: root@ops-00:/usr/local/nagios/libexec# ./check_snmp -H 192.168.1.100 -o DEVICE-MIB::CurrentNoiseFloor.0 -w ~:-85 -c ~:-80 -vvvv Range format incorrect And if I run it with no thresholds defined, it works properly and returns the right value. This makes the graphs correct, however it'll never generate a notification when out of range: root@ops-00:/usr/local/nagios/libexec# ./check_snmp -H 192.168.1.100 -o DEVICE-MIB::CurrentNoiseFloor.0 -vvvv /usr/bin/snmpget -t 1 -r 5 -m ALL -v 1 [authpriv] 192.168.1.100:161 DEVICE-MIB::CurrentNoiseFloor.0 DEVICE-MIB::CurrentNoiseFloor.0 = INTEGER: -97 Processing line 1 oidname: DEVICE-MIB::CurrentNoiseFloor.0 response: = INTEGER: -97 SNMP OK - -97 | DEVICE-MIB::CurrentNoiseFloor.0=-97 What am I doing wrong here? How would I, for example, generate a CRITICAL when the noise floor is -80 dBm or higher, a WARNING when it's -85 to -80 dBm, and an OK when -85 dBm or lower? Do I have to write my own SNMP plugins when dealing with negative values?

  Read the article

• Laptop Acer Travelmate 4050 takes over 10 Mins to POST

  - by Belliez

  Hi, I am a computer tech and have received a laptop for repair. I noticed when I turned it on the laptop would not do anything for a min or two (the fan would run up and stop, power led would shine and some cd rom activity then stop). It would sit there with a black screen. Suddenly after a random number of minutes (between 1-20mins!) the Acer BIOS screen would display and POST would happen before booting into Windows XP. It has frozen in XP at various times and pointed towards a CPU fault and over heating. The fan was on its last legs, sounded like a car engine, so I replaced this. Still same issues. I next replaced the CPU like for like. Same problems. Also applied new thermal paste between the cpu and heatsink, when running the fan kicks in occasionally (not as often as I thought it would) and I left it playing mp3, online radio and updating to service pack 3 and it wouldnt freeze. shutting down ok, cold start, not ok. Waits again before showing the BIOS screen. The hard disk was also making a screaming noise (SMART test and chkdsk passed) but I also replaced this. The laptop powers up with and without the battery so dont think its a battery issue. Running out of ideas and wondered if anyone had any advice. Thanks

  Read the article

• "Safely remove hardware"...doesn't.

  - by Kev

  I have an external USB harddisk that I have scripted to safely shut down after a backup, so the backup operator can unplug it, and knows not to if the lights are still on for some reason. It's always worked fine using the DevEject command-line utility. This week it failed for some reason: DevEject 1.0 2003 c't/Matthias Withopf Ejecting 'USB Mass Storage Device' [USB\VID_0411&PID_002A\00000704C8D2]...FAILED (23,5) Error ejecting device USB Mass Storage Device, vetoed (15,5)! Worse yet, using the SRH tray icon, I click Stop, click OK, it pauses about 5 seconds with OK and Cancel greyed out, closes the sub-window, and then the main window with the Stop button still shows the device, and Stop is still available. I can keep doing that and it never gets rid of the device. I can still access it in Explorer. LockHunter reports that nothing is locking the drive. I've made no changes to the backup configuration or anything to do with the drive this week. Why the sudden flake-out? Short of a restart, which I can't do today before the backup operator goes home, how do I fix it?

  Read the article

• Windows 2008 64bit: applications and explorer always hang

  - by Phil Farthing

  I setup a couple of Window 2008 64bit systems about 5 months ago. Initially all seemed well. Now however, for no apparent reason, things are dog slow, apps hang, explorer hangs, just clicking on something can cause a CPU spike of 100%, and often it's explorer that is eating it up. As I have two on identical hardware, and they experience the same problem, it doesn't seem related to addon software. The only thing these have in common is Kaspersky and I've tried disabling/uninstalling to no avail. There are no useful error messages in the event logs. Actually, the system never even reports app hangs. Sometimes, it similar to what I've seen on Windows 7 systems where the screen goes milky and asks if I want to trouble shoot, that's only when get impatient and click happy. The really odd thing, is that it will NOT do this for a few minutes at a time, and then starts up again. Like I will click on the start menu and browse for the Admin Tools, the start menu will hang at some point and I'll have to wait about a minute, then it's OK. The next time I do this, a few seconds later, it's fine. Every click seems to hang the first time around, then be ok the second time if I do the exact same thing. If anyone has any suggestions, please PLEASE let me know! thanks =)

  Read the article

• Microsoft , Hotmail , Live , MSN, Outlook , unable to send emails and no support received from microsoft in 3 months we are trying asking for that

  - by bombastic

  Ok this is somenthing unbelievable, we have a website, users sign up and receives links to confirm they signed up BUT: 1 - microsoft blocked our IP (no one with microsoft email account can receive our emails) 2 - we tryed contacting microsoft submitting the detailed form about our problem 3 - we posted 3 times in their community about our problem 4 - we tweeted they about our problem 5 - we tryed finding out some telephone support number (the few there are arent' helping at all) Do you think we solved? the answer is NO :/ We still unable to send emails from our IP to microsoft email accounts, since 3 months back. Our emails are perfect we checked all the email headers following microsoft guidelines but it seems not enought, checking our IP reputation it seems everythings ok, indeed we can send email easly to any other provider , gmail, yahoo, etc Do you know any other way to try to get help ? FULL STACK ERROR FROM MICROSOFT: host mx1.hotmail.com[65.55.37.120] said: 550 SC-001 (COL0-MC4-F28) Unfortunately, messages from 94.23.***** weren't sent. Please contact your Internet service provider since part of their network is on our block list. You can also refer your provider to http://mail.live.com/mail/troubleshooting.aspx#errors. (in reply to MAIL FROM command) We are running a Virtual Private Server , so no HOSTING SITE, using NGINX too

  Read the article

< Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >