Search Results

Search found 15646 results on 626 pages for 'port 80'.

Page 68/626 | < Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >

• Cisco Catalyst 3550 + Alteon 184 Load-Balancing Issues...

  - by upkels

  I have just deployed a couple Cisco Catalyst 3550 switches, and a couple Alteon 184 Web Switches for load-balancing. I can ping all RIPs and VIPs to/from the Alteon. Topology Before: (server) <- (Alteon) <- (Internet) Topology Now: (server) <- (3550) <- Alteon <- (Internet) Cisco Port Configuration (Alteon Uplink Port): description LB_1_PORT_9_PRIMARY switchport access vlan 10 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 9 Configuration (VLAN 10 WAN): >> Main# /c/port 9/cur Current Port 9 configuration: enabled pref fast, backup gig, PVID 10, BW Contract 1024 name UPLINK >> Main# /c/port 9/fast/cur Current Port 9 Fast link configuration: speed 100, mode full duplex, fctl none, auto off Cisco Configuration (Load-Balanced Servers Port): description LB_1_PORT_1_PRIMARY switchport access vlan 30 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 1 Configuration (VLAN 30 LOAD-BALANCED LAN): >> Main# /c/port 1/cur Current Port 1 configuration: enabled pref fast, backup gig, PVID 30, BW Contract 1024 name LB_PORT_1 >> Main# /c/port 1/fast/cur Current Port 1 Fast link configuration: speed 100, mode full duplex, fctl both, auto on Each of my servers are on vlan 10 and 30, properly communicating. I have tried to turn on VLAN tagging on the Alteon, however it seems to cause all communications to stop working. When I tcpdump -i vlan30 on any of the webservers, I see normal ARP communications, and some STP communications, which may or may not be part of the problem: ... 15:00:51.035882 STP 802.1d, Config, Flags [none], bridge-id 801e.00:11:5c:62:fe:80.8041, length 42 15:00:51.493154 IP 10.1.1.254.33923 > 10.1.1.1.http: Flags [S], seq 707324510, win 8760, options [mss 1460], length 0 15:00:51.493336 IP 10.1.1.1.http > 10.1.1.254.33923: Flags [S.], seq 3981707623, ack 707324511, win 65535, options [mss 1460], len gth 0 15:00:51.493778 ARP, Request who-has 10.1.3.1 tell 10.1.3.254, length 46 etc... I'm not sure if I've provided enough information, so please let me know if any more is necessary. Thank you!

  Read the article

• Cisco Catalyst 3550 + Alteon 184 Load-Balancing Issues

  - by upkels

  I have just deployed a couple Cisco Catalyst 3550 switches, and a couple Alteon 184 Web Switches for load-balancing. I can ping all RIPs and VIPs to/from the Alteon. Topology Before: (server) <- (Alteon) <- (Internet) Topology Now: (server) <- (3550) <- Alteon <- (Internet) Cisco Port Configuration (Alteon Uplink Port): description LB_1_PORT_9_PRIMARY switchport access vlan 10 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 9 Configuration (VLAN 10 WAN): >> Main# /c/port 9/cur Current Port 9 configuration: enabled pref fast, backup gig, PVID 10, BW Contract 1024 name UPLINK >> Main# /c/port 9/fast/cur Current Port 9 Fast link configuration: speed 100, mode full duplex, fctl none, auto off Cisco Configuration (Load-Balanced Servers Port): description LB_1_PORT_1_PRIMARY switchport access vlan 30 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 1 Configuration (VLAN 30 LOAD-BALANCED LAN): >> Main# /c/port 1/cur Current Port 1 configuration: enabled pref fast, backup gig, PVID 30, BW Contract 1024 name LB_PORT_1 >> Main# /c/port 1/fast/cur Current Port 1 Fast link configuration: speed 100, mode full duplex, fctl both, auto on Each of my servers are on vlan 10 and 30, properly communicating. I have tried to turn on VLAN tagging on the Alteon, however it seems to cause all communications to stop working. When I tcpdump -i vlan30 on any of the webservers, I see normal ARP communications, and some STP communications, which may or may not be part of the problem: ... 15:00:51.035882 STP 802.1d, Config, Flags [none], bridge-id 801e.00:11:5c:62:fe:80.8041, length 42 15:00:51.493154 IP 10.1.1.254.33923 > 10.1.1.1.http: Flags [S], seq 707324510, win 8760, options [mss 1460], length 0 15:00:51.493336 IP 10.1.1.1.http > 10.1.1.254.33923: Flags [S.], seq 3981707623, ack 707324511, win 65535, options [mss 1460], len gth 0 15:00:51.493778 ARP, Request who-has 10.1.3.1 tell 10.1.3.254, length 46 etc... I'm not sure if I've provided enough information, so please let me know if any more is necessary. Thank you!

  Read the article

• Advice on coding Perl to work like PHP

  - by user272273

  I am first and foremost a perl coder, but like many, also code in PHP for client work, especially web apps. I am finding that I am duplicating a lot of my projects in the two languages, but using different paradigms (e.g. for handling cgi input and session data) or functions. What I would like to do is start to code my Perl in a way which is structured more like PHP, so that I a) am keeping one paradigm in my head b) can more quickly port over scripts from one to the other Specifically, I am asking if people could advise how you might do the following in perl? 1) Reproduce the functionality of $_SESSION, $_GET etc. e.g. by wrapping up the param() method of CGI.pm, a session library? 2) Templating library that is similar to PHP I am used to mixing my code and HTML in the PHP convention. e.g. i <h1>HTML Code here</h1> <? print "Hello World\b"; ?> Can anybody advise on which perl templating engine (and possibly configuration) will allow me to code similarly? 3) PHP function library Anybody know of a library for perl which reproduces a lot of the php inbuilt functions?

  Read the article

• Moving delegate-related function to a different thread

  - by Chris

  Hello everybody. We are developing a library in C# that communicates with the serial port. We have a function that is given to a delegate. The problem is that we want it to be run in a different thread. We tried creating a new thread (called DatafromBot) but keep using it as follows (first line): comPort.DataReceived += new SerialDataReceivedEventHandler(comPort_DataReceived); DatafromBot = new Thread(comPort_DataReceived); DatafromBot.Start(); comPort_DataReceived is defined as: Thread DatafromBot; public void comPort_DataReceived(object sender, SerialDataReceivedEventArgs e) { ... } The following errors occur: Error 3 The best overloaded method match for 'System.Threading.Thread.Thread(System.Threading.ThreadStart)' has some invalid arguments C:...\IR52cLow\CommunicationManager.cs 180 27 IR52cLow Error 4 Argument '1': cannot convert from 'method group' to 'System.Threading.ThreadStart' C:...\IR52cLow\CommunicationManager.cs 180 38 IR52cLow Any ideas of how we should convert this to get it to compile? Please note that comPort.DataReceived (pay attention to "." instead of "_") lies within a system library and cannot be modified. Thanks for your time! Chris

  Read the article

• Listing serial (COM) ports on Windows?

  - by Eli Bendersky

  Hello, I'm looking for a robust way to list the available serial (COM) ports on a Windows machine. There's this post about using WMI, but I would like something less .NET specific - I want to get the list of ports in a Python or a C++ program, without .NET. I currently know of two other approaches: Reading the information in the HARDWARE\\DEVICEMAP\\SERIALCOMM registry key. This looks like a great option, but is it robust? I can't find a guarantee online or in MSDN that this registry cell indeed always holds the full list of available ports. Tryint to call CreateFile on COMN with N a number from 1 to something. This isn't good enough, because some COM ports aren't named COMN. For example, some virtual COM ports created are named CSNA0, CSNB0, and so on, so I wouldn't rely on this method. Any other methods/ideas/experience to share? Edit: by the way, here's a simple Python implementation of reading the port names from registry: import _winreg as winreg import itertools def enumerate_serial_ports(): """ Uses the Win32 registry to return a iterator of serial (COM) ports existing on this computer. """ path = 'HARDWARE\\DEVICEMAP\\SERIALCOMM' try: key = winreg.OpenKey(winreg.HKEY_LOCAL_MACHINE, path) except WindowsError: raise IterationError for i in itertools.count(): try: val = winreg.EnumValue(key, i) yield (str(val[1]), str(val[0])) except EnvironmentError: break

  Read the article

• WinCE and PC USB communication

  - by sebeksd

  We are developing some device and we need to find good solution for one of needed functionality. Thing is that we need communicate WinCE 6.0 (ARM) and Windows on PC. Easiest way is of course COM port but in our case it is impossible (all serial ports are used on WinCE and we don't want to add one more). Second option is LAN but for us it is not the best option for few reasons. So there is third option we could use. USB to USB communication but how to do that ? Of course WinCE is USB Device and PC is USB Host so all hardware basics are meet. We could use Active sync but there are few problems with it: - WinCE 6.0 is not working with WMDC (drivers on device just crash after connecting device with PC) and I didn't find any solution for it so in this case we need to use WinXP on PC side (old ActiveSync) - we need to filter communication with active sync to only our application, no other non authorized software should be allowed (what I know this is imposible to obtain). So propably best way to do what we need is to communicate throug USB like standard COM (serial communication). The question is, how it could be made, are we need to write driver on WinCE and also a Driver on Windows (PC), or there are better solution? Maybe some driver for WinCE 6.0 that would emulate Virtual COM on PC side (and of course allow standard Read/Write to it on WinCE side) ? Could someone tell me if something like that exists ?

  Read the article

• Fake serial communication under Linux

  - by kigurai

  I have an application where I want to simulate the connection between a device and a "modem". The device will be connected to a serial port and will talk to the software modem through that. For testing purposes I want to be able to use a mock software device to test send and receive data. Example Python code device = Device() modem = Modem() device.connect(modem) device.write("Hello") modem_reply = device.read() Now, in my final app I will just pass /dev/ttyS1 or COM1 or whatever for the application to use. But how can I do this in software? I am running Linux and application is written in Python. I have tried making a FIFO (mkfifo ~/my_fifo) and that does work, but then I'll need one FIFO for writing and one for reading. What I want is to open ~/my_fake_serial_port and read and write to that. I have also lpayed with the ptymodule, but can't get that to work either. I can get a master and slave file descriptor from pty.openpty() but trying to read or write to them only causes IOError Bad File Descriptor error message.

  Read the article

• .NET SerialPort DataReceived event thread interference with main thread

  - by Kiran

  I am writing a serial communication program using the SerialPort class in C# to interact with a strip machine connected via a RS232 cable. When i send the command to the machine it responds with some bytes depending on the command. Like when i send a "\D" command, i am expecting to download the machine program data of 180 bytes as a continous string. As per the machine's manual, it suggests as a best practice to send an unreognized characters like comma (,) character to make sure the machine is initialized before sending the first command in the cycle. My serial communication code is as follows: public class SerialHelper { SerialPort commPort = null; string currentReceived = string.Empty; string receivedStr = string.Empty; private bool CommInitialized() { try { commPort = new SerialPort(); commPort.PortName = "COM1"; if (!commPort.IsOpen) commPort.Open(); commPort.BaudRate = 9600; commPort.Parity = System.IO.Ports.Parity.None; commPort.StopBits = StopBits.One; commPort.DataBits = 8; commPort.RtsEnable = true; commPort.DtrEnable = true; commPort.DataReceived += new SerialDataReceivedEventHandler(commPort_DataReceived); return true; } catch (Exception ex) { return false; } } void commPort_DataReceived(object sender, SerialDataReceivedEventArgs e) { SerialPort currentPort = (SerialPort)sender; currentReceived = currentPort.ReadExisting(); receivedStr += currentReceived; } internal int CommIO(string outString, int outLen, ref string inBuffer, int inLen) { receivedStr = string.Empty; inBuffer = string.Empty; if (CommInitialized()) { commPort.Write(outString); } System.Threading.Thread.Sleep(1500); int i = 0; while ((receivedStr.Length < inLen) && i < 10) { System.Threading.Thread.Sleep(500); i += 1; } if (!string.IsNullOrEmpty(receivedStr)) { inBuffer = receivedStr; } commPort.Close(); return inBuffer.Length; } } I am calling this code from a windows form as follows: len = SerialHelperObj.CommIO(",",1,ref inBuffer, 4) len = SerialHelperObj.CommIO(",",1,ref inBuffer, 4) If(inBuffer == "!?*O") { len = SerialHelperObj.CommIO("\D",2,ref inBuffer, 180) } A valid return value from the serial port looks like this: \D00000010000000000010 550 3250 0000256000 and so on ... I am getting some thing like this: \D00000010D,, 000 550 D,, and so on... I feel that my comm calls are getting interferred with the one when i send commands. But i am trying to make sure the result of the comma command then initiating the actual command. but the received thread is inserting the bytes from the previous communication cycle. Can any one please shed some light into this...? I lost quite some hair just trying to get this work. I am not sure where i am doing wrong

  Read the article

• why is port 500 in use and how can I free it? VPNC error

  - by kirill_igum

  i tried to use network manager to connect to my university's vpn; it didn't work. then i used a command line vpnc: > sudo vpnc [sudo] password for kirill: Enter IPSec gateway address: vpn.net.**.edu Enter IPSec ID for vpn.net.**.edu: ** Enter IPSec secret for **@vpn.net.**.edu: Enter username for vpn.net.**.edu: ** Enter password for **@vpn.net.**.edu: vpnc: Error binding to source port. Try '--local-port 0' Failed to bind to 0.0.0.0:500: Address already in use then i did this: sudo vpnc --local-port 0 with the same config and it all worked. i'd like to be able to use network manager gui to connect to vpn. I wanted to find out which program uses the port 500: > sudo netstat -a |grep 500 tcp 0 0 *:17500 *:* LISTEN udp 0 0 *:4500 *:* udp 0 0 *:17500 *:* unix 3 [ ] STREAM CONNECTED 63500 unix 3 [ ] STREAM CONNECTED 12500 @/tmp/.X11-unix/X0 there is nothing that uses 500 i'm using ubuntu 10.10 on thinkpad x201t

  Read the article

• Mixing SSL and non-SSL content in an Apache2 virtual host

  - by gravyface

  I have a (hopefully) common scenario for one of my sites that I just can't seem to figure out how to deploy correctly. I have the following site and directories for example.com: These need to require SSL: /var/www/example.com/admin /var/www/example.com/order These need to be non-SSL: /var/www/example.com/maps These need to support both: /var/www/example.com/css /var/www/example.com/js /var/www/example.com/img I have two virtual host declarations for the one site in my /sites-available/example.com file; the top one is *:443 the second one is *:80. Since I have two sites, and if a request comes in on 443, the top virtualhost is used, same with the bottom if it's a port 80 request. However, I can't seem to enforce my SSL requirements using SSLRequireSSL because I'm assuming a port 80 request to /admin or /order is not even hitting the *:443 vhost. Should I just Deny All to /order and /admin within the *:80 virtual host so that if you try to request it on 80, you'll get a 403 Forbidden?

  Read the article

• SQL SERVER – Dedicated Access Control for SQL Server Express Edition – An error occurred while obtaining the dedicated administrator connection (DAC) port.

  - by pinaldave

  Recently I had faced very interesting situation. Due to some reason we were not able to login into the production server for one of client. The reason for the same was that server was very busy, we had to login into the system and bring server to normal situation. When all the attempts failed, I decided to login using Dedicated Administrator Connection (DAC). However when I attempted to connect using DAC it threw following error for me. C:\Users\pinald>sqlcmd -A -d master -S .\SQLEXPRESS Sqlcmd: Error: Microsoft SQL Server Native Client 11.0 : SQL Server Network Interfaces: An error occurred while obtaining the dedicated administrator connection (DAC) port. Make sure that SQL Browser is running, or check the error log for t he port number [xFFFFFFFF]. .Sqlcmd: Error: Microsoft SQL Server Native Client 11.0 : Login timeout expired.Sqlcmd: Error: Microsoft SQL Server Native Client 11.0 : A network-related or instance-specific error has occurred while establishing a connection to SQL Server. Server is not found or not accessible. Check if instance name is correct and if SQL Server is configured to allow remote connections. For more information see SQL Server Books Online. I was bit taken a back as I knew that my commands are correct to login and if DAC does not work, there should be some serious reason for it. When inquired further about the SQL Server version I learned that it was SQL Server Express version deployed. To conserve resources, SQL Server Express does not listen on the DAC port. There is an additional step to be done if SQL Server Express has to be used with DAC. Enable TRACEFLAG on SQL Server Express will enable the connection by DAC possible. Here is the quick methods how one can enable DAC on SQL Server Express. Go to Start >> All Program >>Microsoft SQL Server (your version) >> Configuration Tools >> SQL Server Configuration Manager. Click on SQL Server Services >> Select your SQL Server Express version >> Right Click Properties >> select Startup Parameters Once on the Startup Parameter add the Startup parameter which is TRACEFLAG -T7806. Click on OK and RESTART SQL Server Express edition. Now once again try to connect to SQL Server Express edition and it will work just fine. This is absolutely documented method on BOL and SQL Server Express needs to be restarted. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL Error Messages, SQL Interview Questions and Answers, SQL Query, SQL Server, SQL Tips and Tricks, SQLServer, T SQL, Technology Tagged: SQL Server Express

  Read the article

• Build Open JDK 7 on Mac OSX (TOTD #172)

  - by arungupta

  The complete requirements, pre-requisites, and steps to build OpenJDK 7 port on Mac OSX are described here. The steps are very clearly explained and here are the exact ones I followed on my MacBook Pro 10.7.2: Confirm the version of pre-installed Java as: > java -versionjava version "1.6.0_26"Java(TM) SE Runtime Environment (build 1.6.0_26-b03-383-11A511c)Java HotSpot(TM) 64-Bit Server VM (build 20.1-b02-383, mixed mode) Download and install Mercurial from mercurial.berkwood.com (zip bundle for 10.7 is here). It gets installed in the /usr/local/bin directory. Get the source code as (commands highlighted in bold): hg clone http://hg.openjdk.java.net/macosx-port/macosx-port destination directory: macosx-port requesting all changes adding changesets adding manifests adding file changes added 437 changesets with 364 changes to 33 files updating to branch default 31 files updated, 0 files merged, 0 files removed, 0 files unresolved cd macosx-port chmod 7555 get_source.sh ./get_source.sh # Repos:  corba jaxp jaxws langtools jdk hotspot Starting on corba Starting on jaxp Starting on jaxws Starting on langtools Starting on jdk Starting on hotspot # hg clone http://hg.openjdk.java.net/macosx-port/macosx-port/corba corba requesting all changes adding changesets adding manifests adding file changes added 396 changesets with 3275 changes to 1379 files . . . # exit code 0 # cd ./corba && hg pull -u pulling from http://hg.openjdk.java.net/macosx-port/macosx-port/corba searching for changes no changes found # exit code 0 # cd ./jaxp && hg pull -u pulling from http://hg.openjdk.java.net/macosx-port/macosx-port/jaxp searching for changes no changes found # exit code 0 Install Xcode from the App Store. Include /Developer/usr/bin in PATH. Note: JDK 1.6.0_26 ame pre-installed on my laptop and I installed Xode after that. The compilation went fine and there was no need to re-install the Java for Mac OS X as mentioned in the original steps. Build the code as: make ALLOW_DOWNLOADS=true SA_APPLE_BOOT_JAVA=true ALWAYS_PASS_TEST_GAMMA=true ALT_BOOTDIR=`/usr/libexec/java_home -v 1.6` HOTSPOT_BUILD_JOBS=`sysctl -n hw.ncpu` The final output is shown as: >>>Finished making images @ Sat Nov 19 00:59:04 WET 2011 ... >>>Finished making images @ Sat Nov 19 00:59:04 WET 2011 ...############################################################################# Leaving jdk for target(s) sanity all docs images ################################################################################## Build time 00:17:42 jdk for target(s) sanity all docs images ############################################################################### Build times ##########Target all_product_buildStart 2011-11-19 00:32:40End 2011-11-19 00:59:0400:01:46 corba00:04:07 hotspot00:00:51 jaxp00:01:21 jaxws00:17:42 jdk00:00:37 langtools00:26:24 TOTAL######################### Change the directory and verify the version: >cd build/macosx-universal/j2sdk-image/1.7.0.jdk/Contents/Home/bin >./java -version openjdk version "1.7.0-internal" OpenJDK Runtime Environment (build 1.7.0-internal-arungup_2011_11_19_00_32-b00) OpenJDK 64-Bit Server VM (build 21.0-b17, mixed mode) Now go fix some bugs, file new bugs, or discuss at the macosx-port-dev mailing list.

  Read the article

• not find 127.0.0.1 or vhost with localhost apache in mac

  - by Charly Palencia

  i was working with localhost:81 during a long time with vhost and all was rigth. BUT, right now i need to work over the 80 port and i change the http.conf and http-vhost for used the 80 port but right now into the browser localhost works ok, 127.0.0.1 and the vhost not find the server. my configurations are: * My local machine is lion osx * mamp * HTTP.conf: ServerName localhost:80 * http-vhost NameVirtualHost localhost <VirtualHost localhost> DocumentRoot "/Users/chalien/projects/ownProjects/PHP" ServerName example.dev </VirtualHost> * /private/etc/hosts 127.0.0.1 localhost 255.255.255.255 broadcasthost ::1 localhost fe80::1%lo0 localhost 127.0.0.1 example.dev * /private/etc/services http 80/udp www www-http # World Wide Web HTTP http 80/tcp www www-http # World Wide Web HTTP

  Read the article

• How to DNAT to different local IP based on what public IP was accessed with Shorewall?

  - by mikl

  My server has several public IPs, and is running a bunch of virtual machines with private IP adresses. As an example, I want to map ports 80, 443 and 8080 on 232.21.23.23 (public) to 192.168.122.12 (private). I have tried a couple of different NAT mappings, but none of them seem to work: # This doesn't work. DNAT net loc:192.168.122.12 tcp 80,443,8080 - 232.21.23.23 # Neither does this. DNAT $FW loc:192.168.122.12 tcp 80,443,8080 - 232.21.23.23 # Nor this. DNAT net:232.21.23.23 loc:192.168.122.12 tcp 80,443,8080 # I have no idea what I'm doing. DNAT $FW:232.21.23.23 loc:192.168.122.12 tcp 80,443,8080 Can anyone point me in the right direction?

  Read the article

• How to run VisualSvn Server on port 443 running IIS on same server?

  - by Metro Smurf

  Server 2008 R2 SP1 VisualSvn Server 2.1.6 The IIS server has about 10 sites. One of them uses https over port 443 with the following bindings: http x.x.x.39:80 site.com http x.x.x.39:80 www.site.com https x.x.x.39:443 VisualSvn Server Properties server name: svn.SomeSite.com server port: 443 Server Binding: x.x.x.40 No sites on IIS are listening to x.x.x.40. When starting up VisualSvn server, the following errors are thrown: make_sock: could not bind to address x.x.x.40:443 (OS 10013) An attempt was made to access a socket in a way forbidden by its access permissions. no listening sockets available, shutting down When I stop Site.com on IIS, then VisualSvn Server starts up without a problem. When I bind VisualSvn server to port 8443 and start Site.com, then VisualSvn Server starts without a problem. My goal is to be able to access the VisualSvn Server with a normal url, i.e., one that does't use a port number in the address: https://svn.site.com vs https://svn.site.com:8443 What needs to be configured to allow VisualSvn Server to run on port 443 with IIS running on the same server?

  Read the article

• WPA2 authentication fails on Ubuntu 12.04 using Rosewill RNX-N1

  - by user94156

  Decided to reduce the clutter in the house and replace a wired connection with a wireless one on my wife's system using USB network device Rosewill RNX-X1. I can see and connect to unprotected network, but WPA2 authentication repeatedly fails. RNX-X1 works on other systems (including TV); also have 2 of 'em and tried each. Worth noting that I recently switched from Comcast to CenturyLink and so switched routers. The system connected successfully to previous router (Linksys EA4500) using WPA2. Would think it is the router (Actiontec C1000A) but all other devices (TV, iPad, Windows, Blackberry, and Squeezebox) connect ok. Would appreciate some diagnostic guidance and insight (phrased for a newbie!) Tests to date: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 01 serial: 00:e0:4d:30:40:a1 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:47 ioport:ac00(size=256) memory:fdcff000-fdcfffff memory:fdb00000-fdb1ffff *-network description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan1 serial: 00:02:6f:bd:30:a0 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.2.0-31-generic firmware=0.29 link=no multicast=yes wireless=IEEE 802.11bgn sudo lspci -v 00:00.0 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- 00:01.0 ISA bridge: NVIDIA Corporation MCP67 ISA Bridge (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 00:01.1 SMBus: NVIDIA Corporation MCP67 SMBus (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: 66MHz, fast devsel, IRQ 11 I/O ports at fc00 [size=64] I/O ports at 1c00 [size=64] I/O ports at 1c40 [size=64] Capabilities: [44] Power Management version 2 Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00:01.2 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Flags: 66MHz, fast devsel 00:02.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 Memory at fe02f000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:02.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe02e000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:04.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20 Memory at fe02c000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:06.0 IDE interface: NVIDIA Corporation MCP67 IDE Controller (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] I/O ports at f000 [size=16] Capabilities: [44] Power Management version 2 Kernel driver in use: pata_amd Kernel modules: pata_amd 00:07.0 Audio device: NVIDIA Corporation MCP67 High Definition Audio (rev a1) Subsystem: Biostar Microtech Int'l Corp Device 820c Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe024000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:08.0 PCI bridge: NVIDIA Corporation MCP67 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: fd000000-fd0fffff Capabilities: [b8] Subsystem: NVIDIA Corporation Device cb84 Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- 00:09.0 IDE interface: NVIDIA Corporation MCP67 AHCI Controller (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: Biostar Microtech Int'l Corp Device 5407 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 I/O ports at 09f0 [size=8] I/O ports at 0bf0 [size=4] I/O ports at 0970 [size=8] I/O ports at 0b70 [size=4] I/O ports at dc00 [size=16] Memory at fe02a000 (32-bit, non-prefetchable) [size=8K] Capabilities: [44] Power Management version 2 Capabilities: [8c] SATA HBA v1.0 Capabilities: [b0] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: ahci 00:0b.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0c.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0d.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0e.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 00008000-00008fff Memory behind bridge: fd800000-fd8fffff Prefetchable memory behind bridge: 00000000fd700000-00000000fd7fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0f.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 00007000-00007fff Memory behind bridge: fd600000-fd6fffff Prefetchable memory behind bridge: 00000000fd500000-00000000fd5fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:10.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 I/O behind bridge: 00006000-00006fff Memory behind bridge: fd400000-fd4fffff Prefetchable memory behind bridge: 00000000fd300000-00000000fd3fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:11.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: fd200000-fd2fffff Prefetchable memory behind bridge: 00000000fd100000-00000000fd1fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:12.0 VGA compatible controller: NVIDIA Corporation C68 [GeForce 7050 PV / nForce 630a] (rev a2) (prog-if 00 [VGA controller]) Subsystem: Biostar Microtech Int'l Corp Device 1406 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fb000000 (32-bit, non-prefetchable) [size=16M] Memory at e0000000 (64-bit, prefetchable) [size=256M] Memory at fc000000 (64-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at 80000000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Kernel driver in use: nvidia Kernel modules: nvidia_current, nouveau, nvidiafb 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) Subsystem: Biostar Microtech Int'l Corp Device 2305 Flags: bus master, fast devsel, latency 0, IRQ 47 I/O ports at ac00 [size=256] Memory at fdcff000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at fdb00000 [disabled] [size=128K] Capabilities: [40] Power Management version 2 Capabilities: [48] Vital Product Data Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] Express Endpoint, MSI 00 Capabilities: [84] Vendor Specific Information: Len=4c <?> Capabilities: [100] Advanced Error Reporting Capabilities: [12c] Virtual Channel Capabilities: [148] Device Serial Number 32-00-00-00-10-ec-81-68 Capabilities: [154] Power Budgeting <?> Kernel driver in use: r8169 Kernel modules: r8169 sudo rfkill list all 2: phy2: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• Manage SQL Server Connectivity through Windows Azure Virtual Machines Remote PowerShell

  - by SQLOS Team

  Manage SQL Server Connectivity through Windows Azure Virtual Machines Remote PowerShell Blog This blog post comes from Khalid Mouss, Senior Program Manager in Microsoft SQL Server. Overview The goal of this blog is to demonstrate how we can automate through PowerShell connecting multiple SQL Server deployments in Windows Azure Virtual Machines. We would configure TCP port that we would open (and close) though Windows firewall from a remote PowerShell session to the Virtual Machine (VM). This will demonstrate how to take the advantage of the remote PowerShell support in Windows Azure Virtual Machines to automate the steps required to connect SQL Server in the same cloud service and in different cloud services.  Scenario 1: VMs connected through the same Cloud Service 2 Virtual machines configured in the same cloud service. Both VMs running different SQL Server instances on them. Both VMs configured with remote PowerShell turned on to be able to run PS and other commands directly into them remotely in order to re-configure them to allow incoming SQL connections from a remote VM or on premise machine(s). Note: RDP (Remote Desktop Protocol) is kept configured in both VMs by default to be able to remote connect to them and check the connections to SQL instances for demo purposes only; but not actually required. Step 1 – Provision VMs and Configure Ports   Provision VM1; named DemoVM1 as follows (see examples screenshots below if using the portal):   Provision VM2 (DemoVM2) with PowerShell Remoting enabled and connected to DemoVM1 above (see examples screenshots below if using the portal): After provisioning of the 2 VMs above, here is the default port configurations for example: Step2 – Verify / Confirm the TCP port used by the database Engine By the default, the port will be configured to be 1433 – this can be changed to a different port number if desired.   1. RDP to each of the VMs created below – this will also ensure the VMs complete SysPrep(ing) and complete configuration 2. Go to SQL Server Configuration Manager -> SQL Server Network Configuration -> Protocols for <SQL instance> -> TCP/IP - > IP Addresses   3. Confirm the port number used by SQL Server Engine; in this case 1433 4. Update from Windows Authentication to Mixed mode   5.       Restart SQL Server service for the change to take effect 6.       Repeat steps 3., 4., and 5. For the second VM: DemoVM2 Step 3 – Remote Powershell to DemoVM1 Enter-PSSession -ComputerName condemo.cloudapp.net -Port 61503 -Credential <username> -UseSSL -SessionOption (New-PSSessionOption -SkipCACheck -SkipCNCheck) Your will then be prompted to enter the password. Step 4 – Open 1433 port in the Windows firewall netsh advfirewall firewall add rule name="DemoVM1Port" dir=in localport=1433 protocol=TCP action=allow Output: netsh advfirewall firewall show rule name=DemoVM1Port Rule Name:                            DemoVM1Port ---------------------------------------------------------------------- Enabled:                              Yes Direction:                            In Profiles:                             Domain,Private,Public Grouping:                             LocalIP:                              Any RemoteIP:                             Any Protocol:                             TCP LocalPort:                            1433 RemotePort:                           Any Edge traversal:                       No Action:                               Allow Ok. Step 5 – Now connect from DemoVM2 to DB instance in DemoVM1 Step 6 – Close port 1433 in the Windows firewall netsh advfirewall firewall delete rule name=DemoVM1Port Output: Deleted 1 rule(s). Ok. netsh advfirewall firewall show  rule name=DemoVM1Port No rules match the specified criteria.   Step 7 – Try to connect from DemoVM2 to DB Instance in DemoVM1  Because port 1433 has been closed (in step 6) in the Windows Firewall in VM1 machine, we can longer connect from VM3 remotely to VM1. Scenario 2: VMs provisioned in different Cloud Services 2 Virtual machines configured in different cloud services. Both VMs running different SQL Server instances on them. Both VMs configured with remote PowerShell turned on to be able to run PS and other commands directly into them remotely in order to re-configure them to allow incoming SQL connections from a remote VM or on on-premise machine(s). Note: RDP (Remote Desktop Protocol) is kept configured in both VMs by default to be able to remote connect to them and check the connections to SQL instances for demo purposes only; but not actually needed. Step 1 – Provision new VM3 Provision VM3; named DemoVM3 as follows (see examples screenshots below if using the portal): After provisioning is complete, here is the default port configurations: Step 2 – Add public port to VM1 connect to from VM3’s DB instance Since VM3 and VM1 are not connected in the same cloud service, we will need to specify the full DNS address while connecting between the machines which includes the public port. We shall add a public port 57000 in this case that is linked to private port 1433 which will be used later to connect to the DB instance. Step 3 – Remote Powershell to DemoVM1 Enter-PSSession -ComputerName condemo.cloudapp.net -Port 61503 -Credential <UserName> -UseSSL -SessionOption (New-PSSessionOption -SkipCACheck -SkipCNCheck) You will then be prompted to enter the password.   Step 4 – Open 1433 port in the Windows firewall netsh advfirewall firewall add rule name="DemoVM1Port" dir=in localport=1433 protocol=TCP action=allow Output: Ok. netsh advfirewall firewall show rule name=DemoVM1Port Rule Name:                            DemoVM1Port ---------------------------------------------------------------------- Enabled:                              Yes Direction:                            In Profiles:                             Domain,Private,Public Grouping:                             LocalIP:                              Any RemoteIP:                             Any Protocol:                             TCP LocalPort:                            1433 RemotePort:                           Any Edge traversal:                       No Action:                               Allow Ok.   Step 5 – Now connect from DemoVM3 to DB instance in DemoVM1 RDP into VM3, launch SSM and Connect to VM1’s DB instance as follows. You must specify the full server name using the DNS address and public port number configured above. Step 6 – Close port 1433 in the Windows firewall netsh advfirewall firewall delete rule name=DemoVM1Port   Output: Deleted 1 rule(s). Ok. netsh advfirewall firewall show  rule name=DemoVM1Port No rules match the specified criteria.  Step 7 – Try to connect from DemoVM2 to DB Instance in DemoVM1  Because port 1433 has been closed (in step 6) in the Windows Firewall in VM1 machine, we can no longer connect from VM3 remotely to VM1. Conclusion Through the new support for remote PowerShell in Windows Azure Virtual Machines, one can script and automate many Virtual Machine and SQL management tasks. In this blog, we have demonstrated, how to start a remote PowerShell session, re-configure Virtual Machine firewall to allow (or disallow) SQL Server connections. References SQL Server in Windows Azure Virtual Machines   Originally posted at http://blogs.msdn.com/b/sqlosteam/

  Read the article

• Virtual host in Apache Zend

  - by llocani

  I'd like to ask you if you can tell me why I can't get Vhost in Apache to work my Vhostconf is: NameVirtualHost *:80 <VirtualHost _default_:80> ServerAdmin [email protected] DocumentRoot "E:/Archivos de programa/Zend/Apache2/htdocs" ServerName localhost <Directory "E:/Archivos de programa/Zend/Apache2/htdocs"> Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> #AllowOveride all </VirtualHost> <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/HealingHands" ServerName healinghands.loc <Directory "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/HealingHands"> Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> ErrorLog "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/HealingHands/logs/error.log" CustomLog "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/HealingHands/logs/access.log" common #AllowOveride all </VirtualHost> <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects" ServerName dev.loc <Directory "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects"> Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> ErrorLog "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/logs/error.log" CustomLog "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/logs/access.log" common #AllowOveride all </VirtualHost> My httpd.conf is: ServerRoot "E:\Archivos de programa\Zend\Apache2" Listen 80 LoadModule actions_module modules/mod_actions.so LoadModule alias_module modules/mod_alias.so LoadModule asis_module modules/mod_asis.so LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule auth_digest_module modules/mod_auth_digest.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule cgi_module modules/mod_cgi.so LoadModule dir_module modules/mod_dir.so LoadModule env_module modules/mod_env.so LoadModule filter_module modules/mod_filter.so LoadModule headers_module modules/mod_headers.so LoadModule imagemap_module modules/mod_imagemap.so LoadModule include_module modules/mod_include.so LoadModule info_module modules/mod_info.so LoadModule isapi_module modules/mod_isapi.so LoadModule log_config_module modules/mod_log_config.so LoadModule mime_module modules/mod_mime.so LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule ssl_module modules/mod_ssl.so LoadModule status_module modules/mod_status.so LoadModule userdir_module modules/mod_userdir.so <IfModule !mpm_netware_module> <IfModule !mpm_winnt_module> User daemon Group daemon </IfModule> </IfModule> ServerAdmin [email protected] DocumentRoot "E:\Archivos de programa\Zend\Apache2/htdocs" <Directory /> Options FollowSymLinks AllowOverride all Order allow,deny Allow from all </Directory> <IfModule dir_module> DirectoryIndex index.php index.html home.php </IfModule> <FilesMatch "^\.ht"> Order allow,deny Deny from all Satisfy All </FilesMatch> ErrorLog "logs/error.log" LogLevel warn <IfModule log_config_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> CustomLog "logs/access.log" common </IfModule> <IfModule alias_module> Alias /NetBeansProjects "E:\Documents and Settings\dvieira\Mis documentos\NetBeansProjects" ScriptAlias /cgi-bin/ "E:\Archivos de programa\Zend\Apache2/cgi-bin/" </IfModule> <IfModule cgid_module> </IfModule> <Directory "E:\Archivos de programa\Zend\Apache2/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> DefaultType text/plain <IfModule mime_module> TypesConfig conf/mime.types AddType application/x-compress .Z AddType application/x-gzip .gz .tgz </IfModule> Include conf/extra/httpd-vhosts.conf <IfModule ssl_module> SSLRandomSeed startup builtin SSLRandomSeed connect builtin </IfModule> Include "conf/zend.conf" NameVirtualHost *:80 <VirtualHost *:80> Include "E:\Archivos de programa\Zend\ZendServer/etc/sites.d/zend-default-vhost-80.conf" </VirtualHost> Include "E:\Archivos de programa\Zend\ZendServer/etc/sites.d/globals-*.conf" Include "E:\Archivos de programa\Zend\ZendServer/etc/sites.d/vhost_*.conf" And my host in Windows: 127.0.0.1 localhost 127.0.0.1 healinghands.loc 127.0.0.1 dev.loc And I can't get any of the browser to recognize dev.loc or healinghands.loc but a ping does it. Localhost is working fine. I've spent 3 days now traying to solve this for my one but I finally quit and have to ask. The error should be this Error Code 11002: host not found. Background: this error indicates that the gateway could not find an authoritative DNS server for the website you are trying to access. Date: 5/20/2013 5:51:03 PM Server: Source: DNS problem. i'd like to add this ping Haciendo ping a healinghands.loc [127.0.0.1] con 32 bytes de datos: Respuesta desde 127.0.0.1: bytes=32 tiempo<1m TTL=128 Respuesta desde 127.0.0.1: bytes=32 tiempo<1m TTL=128 Respuesta desde 127.0.0.1: bytes=32 tiempo<1m TTL=128 Respuesta desde 127.0.0.1: bytes=32 tiempo<1m TTL=128 Estadísticas de ping para 127.0.0.1: Paquetes: enviados = 4, recibidos = 4, perdidos = 0 (0% perdidos), Tiempos aproximados de ida y vuelta en milisegundos: Mínimo = 0ms, Máximo = 0ms, Media = 0ms Today i've tryed something: i've add this domains into the exceptions of mi ie proxy config. This worked for healinghands.loc but not for dev.loc i really do not understand why, both config are exactly the same except for de documentroot. I will continue searching

  Read the article

• WPA2 authentication fails using USB network devices (Linksys and Rosewill)

  - by Greg Youtz

  Decided to reduce the clutter in the house and replace a wired connection with a wireless one on my wife's system using USB network device Rosewill RNX-X1. I can see and connect to unprotected network, but WPA2 authentication repeatedly fails. Tried the same with a Linksys USB network adapter. Both failed to authenticate. Worth noting that I recently switched from Comcast to CenturyLink and so switched routers. The system connected successfully to previous router (Linksys EA4500) using WPA2. Would think it is the router (Actiontec C1000A) but all other devices (TV, iPad, Windows, Blackberry, and Squeezebox) connect ok. Would appreciate some diagnostic guidance and insight (phrased for a newbie!) Tests to date: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 01 serial: 00:e0:4d:30:40:a1 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:47 ioport:ac00(size=256) memory:fdcff000-fdcfffff memory:fdb00000-fdb1ffff *-network description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan1 serial: 00:02:6f:bd:30:a0 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.2.0-31-generic firmware=0.29 link=no multicast=yes wireless=IEEE 802.11bgn sudo lspci -v 00:00.0 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- 00:01.0 ISA bridge: NVIDIA Corporation MCP67 ISA Bridge (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 00:01.1 SMBus: NVIDIA Corporation MCP67 SMBus (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: 66MHz, fast devsel, IRQ 11 I/O ports at fc00 [size=64] I/O ports at 1c00 [size=64] I/O ports at 1c40 [size=64] Capabilities: [44] Power Management version 2 Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00:01.2 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Flags: 66MHz, fast devsel 00:02.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 Memory at fe02f000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:02.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe02e000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:04.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20 Memory at fe02c000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:06.0 IDE interface: NVIDIA Corporation MCP67 IDE Controller (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] I/O ports at f000 [size=16] Capabilities: [44] Power Management version 2 Kernel driver in use: pata_amd Kernel modules: pata_amd 00:07.0 Audio device: NVIDIA Corporation MCP67 High Definition Audio (rev a1) Subsystem: Biostar Microtech Int'l Corp Device 820c Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe024000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:08.0 PCI bridge: NVIDIA Corporation MCP67 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: fd000000-fd0fffff Capabilities: [b8] Subsystem: NVIDIA Corporation Device cb84 Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- 00:09.0 IDE interface: NVIDIA Corporation MCP67 AHCI Controller (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: Biostar Microtech Int'l Corp Device 5407 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 I/O ports at 09f0 [size=8] I/O ports at 0bf0 [size=4] I/O ports at 0970 [size=8] I/O ports at 0b70 [size=4] I/O ports at dc00 [size=16] Memory at fe02a000 (32-bit, non-prefetchable) [size=8K] Capabilities: [44] Power Management version 2 Capabilities: [8c] SATA HBA v1.0 Capabilities: [b0] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: ahci 00:0b.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0c.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0d.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0e.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 00008000-00008fff Memory behind bridge: fd800000-fd8fffff Prefetchable memory behind bridge: 00000000fd700000-00000000fd7fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0f.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 00007000-00007fff Memory behind bridge: fd600000-fd6fffff Prefetchable memory behind bridge: 00000000fd500000-00000000fd5fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:10.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 I/O behind bridge: 00006000-00006fff Memory behind bridge: fd400000-fd4fffff Prefetchable memory behind bridge: 00000000fd300000-00000000fd3fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:11.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: fd200000-fd2fffff Prefetchable memory behind bridge: 00000000fd100000-00000000fd1fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:12.0 VGA compatible controller: NVIDIA Corporation C68 [GeForce 7050 PV / nForce 630a] (rev a2) (prog-if 00 [VGA controller]) Subsystem: Biostar Microtech Int'l Corp Device 1406 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fb000000 (32-bit, non-prefetchable) [size=16M] Memory at e0000000 (64-bit, prefetchable) [size=256M] Memory at fc000000 (64-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at 80000000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Kernel driver in use: nvidia Kernel modules: nvidia_current, nouveau, nvidiafb 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) Subsystem: Biostar Microtech Int'l Corp Device 2305 Flags: bus master, fast devsel, latency 0, IRQ 47 I/O ports at ac00 [size=256] Memory at fdcff000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at fdb00000 [disabled] [size=128K] Capabilities: [40] Power Management version 2 Capabilities: [48] Vital Product Data Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] Express Endpoint, MSI 00 Capabilities: [84] Vendor Specific Information: Len=4c <?> Capabilities: [100] Advanced Error Reporting Capabilities: [12c] Virtual Channel Capabilities: [148] Device Serial Number 32-00-00-00-10-ec-81-68 Capabilities: [154] Power Budgeting <?> Kernel driver in use: r8169 Kernel modules: r8169 sudo rfkill list all 2: phy2: Wireless LAN Soft blocked: no Hard blocked: no Would appreciate insight on how to chase this down.

  Read the article

• FreeBSD Ports: How can I see all dependencies, and all dependencies for those dependencies, for a port?

  - by Stefan Lasiewski

  I'm trying to build a port which depends on apache-ant. I thought I could run make build-depends-list to see all dependencies required by this port: # make build-depends-list /usr/ports/devel/apache-ant /usr/ports/java/jdk16 /usr/ports/math/gmp But after installing everything, the port had a dependency list which was a mile long: apache-ant-1.8.1 desktop-file-utils-0.15_2 gamin-0.1.10_4 gettext-0.18.1.1 gio-fam-backend-2.26.1 glib-2.26.1_1 gmp-5.0.1 inputproto-2.0 javavmwrapper-2.3.5 kbproto-1.0.4 libX11-1.3.3_1,1 libXau-1.0.5 libXdmcp-1.0.3 libXext-1.1.1,1 libXi-1.3,1 libXtst-1.1.0 libiconv-1.13.1_1 libpthread-stubs-0.3_3 libxcb-1.7 pcre-8.12 perl-5.10.1_3 pkg-config-0.25_1 python26-2.6.6 recordproto-1.14 unzip-6.0 xextproto-7.1.1 xproto How can I see all dependencies, and all subdependencies for a port?

  Read the article

• why I can not install Gphpedit

  - by Mohamed Samir Khalil

  why I can not install Gphpedit and I get this errors: Failed to fetch //http://security.ubuntu.com/ubuntu/pool/main/w/webkit/libjavascriptcoregtk-1.0-0_1.8.1-0ubuntu0.12.04.1_amd64.deb 404 Not Found [IP: 91.189.92.190 80] Failed to fetch //http://security.ubuntu.com/ubuntu/pool/main/w/webkit/libwebkitgtk-1.0-common_1.8.1-0ubuntu0.12.04.1_all.deb 404 Not Found [IP: 91.189.92.190 80] Failed to fetch //http://security.ubuntu.com/ubuntu/pool/main/w/webkit/libwebkitgtk-1.0-0_1.8.1-0ubuntu0.12.04.1_amd64.deb 404 Not Found [IP: 91.189.92.190 80]

  Read the article

• Error using SoapClient() in PHP [migrated]

  - by Dhaval

  I'm trying to access WSDL(Web Service Definition Language) file using SoapClient() of PHP. I found that WSDL file is authenticated. I tried with passing credentials on an array by another parameter and active SSL on my server, still I'm getting an error. Here is the code I'm using: $client = new SoapClient("https://webservices.chargepointportal.net:8081/coulomb_api_1.1.wsdl",array("trace" = "1","Username" = "username","Password" = "password")); Here is the error I'm getting: Warning: SoapClient::SoapClient(https://webservices.chargepointportal.net:8081/coulomb_api_1.1.wsdl) [soapclient.soapclient]: failed to open stream: Connection timed out in PATH_TO_FILE on line 80 Warning: SoapClient::SoapClient() [soapclient.soapclient]: I/O warning : failed to load external entity "https://webservices.chargepointportal.net:8081/coulomb_api_1.1.wsdl" in PATH_TO_FILE on line 80 Fatal error: Uncaught SoapFault exception: [WSDL] SOAP-ERROR: Parsing WSDL: Couldn't load from 'https://webservices.chargepointportal.net:8081/coulomb_api_1.1.wsdl' : failed to load external entity "https://webservices.chargepointportal.net:8081/coulomb_api_1.1.wsdl" in PATH_TO_FILE:80 Stack trace: #0 /home2/wingstec/public_html/widget/API/index.php(80): SoapClient-SoapClient('https://webserv...', Array) #1 {main} thrown in PATH_TO_FILE on line 80 It seems that error says file not exist at the path we given but when we run that path directly on browser then we're getting that file Can anyone help me to figure out what the exactly problem is?

  Read the article

• Can iptables allow Squid to process a request, then redirect the response packets to another port?

  - by Dan H

  I'm trying to test a fancy traffic analyzer app, which I have running on port 8890. My current plan is to let any HTTP request come into Squid, on port 3128, and let it process the request, and then just before it sends the response back, use iptables to redirect the response packets (leaving port 3128) to port 8890. I've researched this all night, and tried many iptables commands, but I'm missing something and my hair is falling out. I thought something like this would work: iptables -t nat -A OUTPUT -p tcp --sport 3128 -j REDIRECT --to-ports 8990 This rule gets created ok, but it never redirects anything. Is this even possible? If so, what iptables incantation could do it? If not, any idea what might work on a single host, given multiple remote browser clients?

  Read the article

• how can make transparent proxy on more than one port?

  - by ermya

  i want to make transparent proxy with linux ( centos) , i want all incoming connection on port 1000 - 2000 on eth0 forward to eth1 on port 1000 - 2000 in transparent mode i have 2 server 1- linux ( proxy server) 2- windows i want protect my windows server with my linux server firewall also i must make transparent proxy with my linux server linux server have 2 interface one for public network an another for private network connected to windows server so all incoming connection must connect to the linux server (at eth0 public network) first and after checking , must forward to the windows server on private network (with linux interface eth1 ) i can use squid for making transparent proxy but i dont know how i must config the squid for multi port because i want listen in more than 1000 ports for example from port 1000 to 2000 anyone know how can i do ?

  Read the article

• Installing Yaws server on Ubuntu 12.04 (Using a cloud service)

  - by Lee Torres

  I'm trying to get a Yaws web server working on a cloud service (Amazon AWS). I've compilled and installed a local copy on the server. My problem is that I can't get Yaws to run while running on either port 8000 or port 80. I have the following configuration in yaws.conf: port = 8000 listen = 0.0.0.0 docroot = /home/ubuntu/yaws/www/test dir_listings = true This produces the following successful launch/result: Eshell V5.8.5 (abort with ^G) =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Using config file /home/ubuntu/yaws.conf =INFO REPORT==== 16-Sep-2012::17:21:06 === Ctlfile : /home/ubuntu/.yaws/yaws/default/CTL =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Listening to 0.0.0.0:8000 for <3> virtual servers: - http://domU-12-31-39-0B-1A-F6:8000 under /home/ubuntu/yaws/www/trial - =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Listening to 0.0.0.0:4443 for <1> virtual servers: - When I try to access the the url (http://ec2-72-44-47-235.compute-1.amazonaws.com), it never connects. I've tried using paping to check if port 80 or 8000 is open(http://code.google.com/p/paping/) and I get a "Host can not be resolved" error, so obviously something isn't working. I've also tried setting the yaws.conf so its at Port 80, appearing like this: port = 8000 listen = 0.0.0.0 docroot = /home/ubuntu/yaws/www/test dir_listings = true and I get the following error: =ERROR REPORT==== 16-Sep-2012::17:24:47 === Yaws: Failed to listen 0.0.0.0:80 : {error,eacces} =ERROR REPORT==== 16-Sep-2012::17:24:47 === Can't listen to socket: {error,eacces} =ERROR REPORT==== 16-Sep-2012::17:24:47 === Top proc died, terminate gserv =ERROR REPORT==== 16-Sep-2012::17:24:47 === Top proc died, terminate gserv =INFO REPORT==== 16-Sep-2012::17:24:47 === application: yaws exited: {shutdown,{yaws_app,start,[normal,[]]}} type: permanent {"Kernel pid terminated",application_controller," {application_start_failure,yaws,>>>>>>{shutdown,>{yaws_app,start,[normal,[]]}}}"} I've also opened up the port 80 using iptables. Running sudo iptables -L gives this output: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- ip-192-168-2-0.ec2.internal ip-192-168-2-16.ec2.internal tcp dpt:http ACCEPT tcp -- 0.0.0.0 anywhere tcp dpt:http ACCEPT all -- anywhere anywhere ctstate RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:http Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination In addition, I've gone to the security group panel in the Amazon AWS configuration area, and add ports 80, 8000, and 8080 to ip source 0.0.0.0 Please note: if you try to access the URL of the virtual server now, it likely won't connect because I'm not running currently running the yaws daemon. I've tested it when I've run yaws either through yaws or yaws -i Thanks for the patience

  Read the article

< Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >