Search Results

Search found 9280 results on 372 pages for 'wireless card'.

Page 68/372 | < Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >

  • Can't control connection bit rate using iwconfig with Atheros TL-WN821N (AR7010)

    - by Paul H
    I'm trying to reduce the connection bit rate on my Atheros TP-Link TL-WN821N v3 usb wifi adapter due to frequent instability issues (reported connection speed goes down to 1Mb/s and I have to physically reconnect the adapter to regain a connection). I know this is a common problem with this device, and I have tried everything I can think of to fix it, including using drivers from linux-backports; compiling and installing a custom firmware (following instructions on https://wiki.debian.org/ath9k_htc#fw-free) and (as a last resort) using ndiswrapper. When using ndiswrapper, the wifi adapter is stable and operates in g mode at 54Mb/s (whilst when using the default ath9k_htc module, the adapter connects in n mode and the bit rate fluctuates constantly). Unfortunately, with this setup I have to run my processor using only one core, since using SMP with ndiswrapper causes a kernel oops on my system. So I want to lock my bit rate to 54Mb/s (or less, if need be) for connection stability, using the ath9k_htc module. I've tried 'sudo iwconfig wlan0 rate 54M'; the command runs with no error but when I check the bit rate with 'sudo iwlist wlan0 bitrate' the command returns: wlan0 unknown bit-rate information. Current Bit Rate:78 Mb/s Any ideas? Here's some info (hopefully relevant) on my setup: Xubuntu (12.04.3) 64bit (kernel 3.2.0-55.85-generic) using Network Manager. My Router is from Virgin Media, the VMDG480. lshw -C network : *-network description: Wireless interface physical id: 1 bus info: usb@1:4 logical name: wlan0 serial: 74:ea:3a:8f:16:b6 capabilities: ethernet physical wireless configuration: broadcast=yes driver=ath9k_htc driverversion=3.2.0-55 firmware=1.3 ip=192.168.0.9 link=yes multicast=yes wireless=IEEE 802.11bgn lsusb -v: Bus 001 Device 003: ID 0cf3:7015 Atheros Communications, Inc. TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 idVendor 0x0cf3 Atheros Communications, Inc. idProduct 0x7015 TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] bcdDevice 2.02 iManufacturer 16 ATHEROS iProduct 32 UB95 iSerial 48 12345 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 60 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 6 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x06 EP 6 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) iwlist wlan0 scanning: wlan0 Scan completed : Cell 01 - Address: C4:3D:C7:3A:1F:5D Channel:1 Frequency:2.412 GHz (Channel 1) Quality=37/70 Signal level=-73 dBm Encryption key:on ESSID:"my essid" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master Extra:tsf=00000070cca77186 Extra: Last beacon: 5588ms ago IE: Unknown: 0007756E69636F726E IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 32040C121860 IE: Unknown: 2D1AFC181BFFFF000000000000000000000000000000000000000000 IE: Unknown: 3D1601080400000000000000000000000000000000000000 IE: Unknown: DD7E0050F204104A0001101044000102103B00010310470010F99C335D7BAC57FB00137DFA79600220102100074E657467656172102300074E6574676561721024000631323334353610420007303030303030311054000800060050F20400011011000743473331303144100800022008103C0001011049000600372A000120 IE: Unknown: DD090010180203F02C0000 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 iwconfig: lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"my essid" Mode:Managed Frequency:2.412 GHz Access Point: C4:3D:C7:3A:1F:5D Bit Rate=78 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0,

    Read the article

  • how to download and install from the internet >> skype and realplayer

    - by ADAM
    i had corrupted win7 by dead blue screen and stopped rebooting or installing or safe mode. just death i installed linux unubtu one i still unable to install my wireless stick modem for surfing internet wirelessly form my provider vividwireless i don't know where or how to download porg and app from the net like real player and skype and others and to intall them. even i cannot find them after download. can i revive and reboot or fix my dead win7 os from linux. i can connect internet from wireless network in the neighborhood linksys!! what is linksys anyway? how to use linux ubuntu same way like windows? ie. insalling, using cd rom for installation and downloading and cleaning history and cache and system restore? please email me to: [email protected] any help..step by step many thanks

    Read the article

  • How do I do a B43 Legacy install on Ubuntu 11.10?

    - by Gozzy
    I recently installed ubuntu onto an extra hard drive and everything booted correctly. However, my Linksys wireless card is not working. I went though all the forums and walk throughs and I know that I need to install the b43 legacy firmware to get the card to work. When I try to install the files, I keep getting the message in Terminal saying "No such file or directory" for every file i need to run. It's Ubuntu 11.10 on a dell optiplex gx280. Also, the "pool" file that is supposed to be on the file system is not there

    Read the article

  • How to stop my wireless adapter from received dhcp from router (windows)

    - by baobeiii
    Hi, I have a windows 7 computer which is connected via vpn to an OpenVpn server which happens to be in another country. I have all internet traffic being routed from my computer through the vpn to the server. However dns queries are not going through the vpn, but are instead going directly to my isp's dns via a route outside of the vpn tunnel. This is happening because my wireless adapter is configured to obtain DNS server address automatically. The router that stands between my computer and the internet happens to have a DCHP server running on it that is assinging my computer with the DNS addresses of the isp. The issue is, i haven't been able to stop my wireless adapter on my computer from receiving the dns settings from the router. I've tried selecting 'use the following dns server addresses' and then just leaving them blank, but ipconfig /all shows me that this hasn't worked and i'm still getting dns form the router. So is there any way to completely stop my windows wireless adapter from receiving these settings from the router? I have the OpenVpn server pushing to my computer's tun adapter the dns that it should be using. I'd rather solve this in a way that doesn't involve disabling the dhcp server on the router or fiddling with the router. The reason is i'm on a laptop and i want my vpn to not leak dns even when i'm out, for example in wireless hotspots. I know if i could just force the wireless adapter to ignore the router's dhcp server then my dns queries would go through the tunnel to the dns address pushed by the OpenVpn server. Sorry, i know thats long winded, if you have any idea's please do tell me. Thanks and merry xmas.

    Read the article

  • Access Domain over Wireless

    - by William
    I have an active directory server and all hard wired clients connect perfectly fine. However any wireless clients do not recognize that they are connected to the domain, despite the dns server being appropriately set to the domain controller for both wired and wireless connections. Also - both wired and wireless clients are on the same subnet. I am using a Verizon food actiontec router. What am I missing? For instance, this is the same computer connected first via an Ethernet cable and second via the wireless.

    Read the article

  • 13.10 suspend kills wifi

    - by ser
    i tried to post to this thread Hardware wireless switch has no effect after suspend and 13.10 upgrade for if i understand their question i am having the same problem but the answer option won't work for me and maybe i am not supposed to post there anyway, i dunno lol...ack when i come out of suspend, the wireless is disconnected with the only way to get it to reinitialize/be recognized is to do a full restart. at first i thought it was my gnome shell (for lock screen disappeared there with 13.10) but when i switched to the default ubuntu it's still doing it and it's kinda driving me nuts for i have to reopen all my files and browsers/tabs/windows everytime. i'm only a geekling so i don't know how to show the terminal stuff the above asker shows, but it sounds like the same issue and it only started with 13.10 upgrade a few days ago. any help would be much appreciated!!! thanks so much ser

    Read the article

  • NetworkManager refuses to manage my WLAN interface

    - by user104167
    I'm using Ubuntu 12.10 with Gnome 3.6 on a brand-new Samsung NP900X4C. The installer detected the wireless adapter, took in the SSID and WPA passphrase, wrote these into /etc/network/interfaces and connected perfectly. Once installation was finished I wanted to switch to using NetworkManager to manage the wireless adapter, since this is much more convenient than fiddling with /etc/network/interfaces every time I find a new hotspot. Therefore I edited /etc/NetworkManager/NetworkManager.conf to set: [ifupdown] managed=true When I rebooted NetworkManager, the problems started: - The NetworkManager tray applet changed from saying device not managed to device not ready - I lost all internet connectivity as wlan0 would not associate to the Access Point - if I set managed=false in NetworkManager.conf and restarted both NetworkManager and networking services from the command-line, the Gnome desktop "semi-crashed" and lost all its Window Decorations, the panel, the launcher and basically became unusable. However if I restart the computer completely after setting managed=false, wlan0 once again works perfectly.

    Read the article

  • In 12.04, with my Linksys WUSB54G USB adapter I can see the networks, but cannot connect to any of them

    - by tobye
    I recently loaded Ubuntu version 12.04 onto my computer, and I have a WUSB54G v4 USB wireless adapter. I first tried to get it to work by simply plugging my adapter into an open USB port. This seemed to work fine, it came up with a list of wireless adapters, so I clicked on the correct one and entered the security code. It looked like it was going to connect. It tried for about five minutes before I stopped it. I then decided to create a network as I also have one setup. I did this and it connected, only one problem, I couldn't get onto the internet. Please help me, I am new to Ubuntu and am totally lost.

    Read the article

  • DVI vs HDMI graphics card output

    - by Shack
    Asking on behalf of someone: I want to buy a new graphics card but do not know which would be best in terms of output, DVI or HDMI, the sound part of the HDMI is not really required, I just need something to go to my new 32 inch hd tv. It accepts both DVI and HDMI. I only need it for basic gaming but mostly as a media center to watch movies and tv shows on. Also for windows media center's TV application, I need a tv card, should I get a graphics card with bult in tv card, or a usb dongle??

    Read the article

  • Joining two routers together, but I have no access to the second router, although I know it's IP address and Gateway

    - by JohnnyVegas
    I have temporarily moved into a rented apartment for 4 months, which has wireless. The trouble I am having is that the access points here are wifi only and no RJ45 and I need to use RJ45 to connect some equipment that I am working with. I have purchased an RT-N66U and installed Tomato (shibby ver. 1.28) and successfully replaced the existing access point, but now I want to enable the access point that I have replaced as it links wirelessly to 3 others. Can I plug in a cable from the access point to my RT-N66U and get it to access the internet via my router? I have no access to the existing wireless access point, and don't want to reset it as it's not mine. There is another router situated in the roof somewhere which I also have no access to, but it's supplying my RT-N66U internet and I most definitely have a double-nat, which although isn't the best way of doing things I am limited with what I can do. Any suggestions on routing tables, vlans etc would be helpful, but I have no experience in these fields before - but I know the tomato firmware can cater for this. My router is set to IP 10.0.1.1 and dhcp is 10.0.1.100-200 The wireless access point address was 192.168.1.2 but this was assigned by the router in the roof which has the address 192.168.1.1. There is a cable from this router going to a wall socket which I now have my RT-N66u attached to via the WAN port. I understand it's scruffy and it isn't the way to do things but I have tried to ask for the admin details but as the wireless network is looked after by a third party and nobody knows their details I am stuck with this dilemma. I could buy three wireless access points and replace the existing but this isn't what I want to do, and although I have installed plenty of DD-WRT wireless repeater bridges they simply don't work here for some unknown reason. The phone line here is very noisy too and I don't have the rights to install ADSL in a building that isn't mine, and 3G coverage isn't good enough either. Thanks for your time

    Read the article

  • I can't connect to my network, except in safe mode

    - by eidylon
    My laptop cannot connect to my network all of a sudden except in safe mode. When it boots, it will show the networks available in the tray popup, but if I click connect on any, it says "Unable to connect" and the troubleshooter is useless. Shortly thereafter all the networks disappear. I have tried removing IPv6 support as I have seen that cause problems. No joy. I've also tried removing the wireless network adapter in Device Manager and reinstalling it, also no joy. I've also tried attaching a USB wireless adapter, and it has the same problem. If I boot in safe mode, then it has no problems at all. Three other devices in the house connect fine, so I am pretty sure it is nothing to do with the router. Any ideas what to check next? I am running Win7 Ultimate on a 2GHz Quadcore with 8GB RAM with a Broadcom 802.11n wireless card. EDIT: RE wired connections: What is very weird is that if i plug in a wired connection, then not only does it connect via the wired connection, but the wireLESS also starts working perfectly. And a soon as I unplug the wire, then the wireLESS stops working again! So it seems the wireless is right now working only in safe-mode, or when a wired connection is also plugged in.

    Read the article

  • XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

    - by ewall
    Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

    Read the article

  • Two VGA monitors on Lenovo IdeaCentre H520 Desktop

    - by Sebastian-Laurentiu Plesciuc
    I recently bought a Lenovo IdeaCentre H520 computer and two VGA LED monitors. This particular PC has a dedicated NVIDIA Geforce GT630 video card and an integrated Intel HD Graphics 2500 video card. Both cards have VGA out. The Geforce card also has a HDMI out. I have installed Windows 8 and I can't seem to use both cards. I have connected both monitors, one to the VGA out of the Geforce card and one to the VGA out of the integrated card. I looked through the BIOS options for Video and I can only select the dedicated one, the integrate one or the Auto option. This kinda sucks. I was wondering what kind of options I have available. I have a VGA female to DVI A male adaptor, I was wondering if it could work if I can hook it to a DVI A female to HDMI male adaptor and plug one monitor into the VGA out of the Geforce video card and the other through both adapters to the HDMI out. Any chance this could work? I was looking online for a VGA to HDMI live cable but it's kind of expensive.

    Read the article

  • At what point does the performance gap between GPU & CPU become so great that the CPU is holding back a system?

    - by Matthew Galloway
    I know that generally speaking for gaming performance the GPU is the primary factor which holds back performance, with everything else such as RAM/motherboard/PSU/CPU being secondary in importance to the graphics card. But at some point the other components ARE going to be significant in holding back the whole system! For instance nobody would be silly enough to play modern games with 512MB RAM and the very latest graphics cards (such as an HD7970) as I bet the performance increase over such a system with only 512MB but a mid range card would be non-existent! Thus it would be a "waste" for such a person to buy any high end graphics card without resolving first the system's other problems. The same point applies to other components, such as if it only had a Pentium II a current high end graphics card would be wasted on it! So my core question is how do you determine at what point for your system is spending on extra GPU power be completely "wasted"? (also, a slightly more nuanced question is trying work out at what point might the extra graphics power not be "wasted" but would be "sub optimal" value for money, when the expenditure should then be split around graphics card and other components. As obviously a gamer shouldn't always just spend on upgrading the graphics card! But needs to balance it out)

    Read the article

  • Comparing 128MB GeForce 8600GT and 512MB Radeon X1650

    - by Synetech inc.
    Hi, I'm trying to determine which is the better of these two video cards: 128MB Nvidia GeForce 8600GT card while the other has a 512MB ATI Radeon X1650 card. Both cards are the upper-level mid-range versions of their respective series. On the one hand, the ATI has substantially more VRAM, but the Nvidia supports D3D 10 and SM4.0 as opposed to D3D 9.0c/SM3.0 that the ATI supports. Also, I have always heard better things about Nvidia cards compared to ATI cards. I'm trying to find some advice on which one is better, but I can't find any actual comparisons or anything for these specific cards (the comparisons I can find are only similar ones like the X1650 Pro or 8600GT PCI-E), so I figure that what I need to know is whether the extra VRAM is that important. Looking at the ATI table and the Nvidia table seems to indicate that the Nvidia is better, but then again, the Nvidia table also says that the GeForce 8600GT is a PCI-E card with at least 256MB even though the card in question is an AGP with 128MB. (:-?) (It looks like the ATI card is not supported in Windows 7 while the Nvidia card is, which I suppose is also a factor, though not quite as immediately relevant as performance.) Any ideas? Thanks a lot.

    Read the article

  • Storing Credit Card Numbers in SESSION - ways around it?

    - by JM4
    I am well aware of PCI Compliance so don't need an earful about storing CC numbers (and especially CVV nums) within our company database during checkout process. However, I want to be safe as possible when handling sensitive consumer information and am curious how to get around passing CC numbers from page to page WITHOUT using SESSION variables if at all possible. My site is built in this way: Step 1) collect Credit Card information from customer - when customer hits submit, the information is first run through JS validation, then run through PHP validation, if all passes he moves to step 2. Step 2) Information is displayed on a review page for customer to make sure the details of their upcoming transaction are shown. Only the first 6 and last 4 of the CC are shown on this page but card type, and exp date are shwon fully. If he clicks proceed, Step 3) The information is sent to another php page which runs one last validation, sends information through secure payment gateway, and string is returned with details. Step 4) If all is good and well, the consumer information (personal, not CC) is stored in DB and redirected to a completion page. If anything is bad, he is informed and told to revisit the CC processing page to try again (max of 3 times). Any suggestions?

    Read the article

  • No Sound card detected in Sound Settings, although sound works

    - by usertwelve
    I have Ubuntu 12.04 installed on my laptop. When I go to Sound Settings while logged into my user, no sound card appears detected. In spite of this, the sound on my laptop is working ok, and I can use alsamixer just fine. The Unity sound indicator is dead, and this is quite annoying. If I login as guest, the sound indicator works just fine, I assume it's something related to my user's sound settings, but I cannot find what exactly. Any clues?

    Read the article

  • Chainload boot of Ubuntu installed on 32GB SD card from legacy Grub boot on USB

    - by Gary Darsey
    I have Ubuntu installed on a 32 GB SD card (in the Storage Expansion slot on an Acer Aspire One) with Grub2 installed in the same partition. I boot into legacy Grub on a USB drive and would like to boot by chainloading Grub2 from Grub (kernel/initrd or symlink booting would also be fine), but I haven't figured out how to do this from legacy Grub CLI. Output from blkid for this partition is /dev/mmcblk0p1: LABEL="Ubuntu" UUID="7ceb9fa7-238c-4c5d-bb8e-2c655652ddec" TYPE='ext4" / fdisk -lu information Boot indicator ID 83. Related entries in grub.cfg: search --no-floppy --fs-uuid --set-root 7ceb9fa7-238c-4c5d-bb8e-2c655652ddec linux /boot/vmlinuz-3.5.0-17-generic root=UUID=7ceb9fa7-238c-4c5d-bb8e-2c655652ddec... initrd /boot/initrd.img-3.5.0-17-generic I can't seem to replicate this in legacy Grub. Is there any way get Grub2 to chainload? How do I set root with UUID in legacy Grub? I prefer to boot from USB. Would Grub2 on USB (copying the grub.cfg generated during installation) be an option?

    Read the article

  • What I need to know if I want credit card payments in an ecommerce website

    - by Andriane
    I live in Costa Rica (central america). I want to build an ecommerce website with credit card payments, I know Asp.NET and SQL Server 2008. I know paypal and the express checkout solution, but many people (and clients) here doesnt like it or dont use it. Paypal and Authorize.Net dont support countries of Latin America, so if you can tell me one company who can or what can I do to setup my shopping cart, im studing right now security and how to implement SSL certificates and encrypt sensible data and PCI compliance in some way. I need this for my own framework in ASP.NET and provide ecommerce solutions here in my country.

    Read the article

  • gnome-shell failed to launch when dual monitor detected, nvidia card

    - by Terry Hu
    I installed a clean precise. I like gnome-shell so I installed it. It worked well with single monitor. But It does not work well when I go to office, plug my external monitor onto my laptop. I am using nvidia driver. Another colleague is using the same laptop, he can work well with dual monitors. His laptop is ATI graphic card. When I plug my extended monitor cable, I choose GNOME, but actually it goes to gnome 2 classic desktop environment, not GNOME 3. When I disconnect the extended monitor, restart X, I can login with GNOME3. Do I have to choose between GNOME3 and extended monitor? It's a hard choose.

    Read the article

  • Pulseaudio no sound card detected. Dummy output only

    - by Zach Smith
    I'm using 12.10 Quantal with Openbox and a .xinitrc script at login instead of a display manager. Its a relatively fresh install and I noticed when I opened pavucontrol the only output was a dummy one. I check around and it appears that my soundcard is physically installed but Pulseaudio isn't detecting it. I'm really unsure what I should do but any help getting my audio back would be appreciated. Edit: further info if its at all useful: dante@dante-ubuntu:~$ uname -a && aplay -l && cat /proc/asound/version && head -n 1 /proc/asound/card*/codec#* Linux dante-ubuntu 3.5.0-17-generic #28-Ubuntu SMP Tue Oct 9 19:31:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux aplay: device_list:252: no soundcards found... Advanced Linux Sound Architecture Driver Version 1.0.25. == /proc/asound/card0/codec#0 <== Codec: ATI R6xx HDMI == /proc/asound/card1/codec#0 <== Codec: IDT 92HD81B1X5

    Read the article

  • Sigmatel sound card not working on an Dell XPS m2010

    - by ralph crowhurst
    I've installed Ubuntu 11.4 on my dell xps m2010 using wubi. Then booted up and could not connect to the Internet using 3three huawei e122 usb mobile broadband (I would like this to work also). I've managed to connect through a wireless network, I went to my favorite sites and was told I needed to install adobe flash player.This what I did players run and picture is good. But there is no sound! Then I've tried to play songs in Banshee, but no sound. I have checked everything in sound preferences including test speaker, there is sound. I have sigmatel sound card. Thanks

    Read the article

  • sound card is not working

    - by ralph crowhurst
    I've installed Ubuntu 11.4 on my dell xps m2010 using wubi. Then booted up and could not connect to the Internet using 3three huawei e122 usb mobile broadband (I would like this to work also). I've managed to connect through a wireless network, I went to my favorite sites and was told I needed to install adobe flash player.This what I did players run and picture is good. But there is no sound! Then I've tried to play songs in Banshee, but no sound. I have checked everything in sound preferences including test speaker, there is sound. I have sigmatel sound card. Thanks

    Read the article

  • Wild card redirect in htaccess giving error this webpage has a redirect loop

    - by kath
    In my website I changed the directory name "vehicles-cars" to "vehicles-cars-for-sale". When I tried to redirect using a wild card redirect from my old directory name to new directory name in my web hosting cPanel account, I get an error every time I open pages from that directory: this webpage has a redirect loop The website is php. The problem is that that I have lots of pages with the old directory indexed in Google and they are getting duplicate content. I really need some advice on what to do with this problem. Here is .htaccess file code for redirect, thanks. RewriteEngine on RewriteCond %{HTTP_HOST} ^adsbuz\.com$ [OR] RewriteCond %{HTTP_HOST} ^www\.adsbuz\.com$ RewriteRule ^vehicles\-cars\/?(.*)$ "http\:\/\/adsbuz\.com\/vehicles\-cars\-for\-sale\/$1" [R=301,L]

    Read the article

  • runt integrated intel graphics card + nvidia pcie graphics card?

    - by Roberto
    Its days I am searching for information/help. Is this possible at all? I am running Ubuntu 11.10 on an intel core i3 530 on a intel dh55hc mainboard. I have 2 monitors attached, one on dvi and one on hdmi. I want to ad a third or eaven a fourth monitor using an additional graphics card nvidia in pcie slot. I cant get an image on all monitors at the same time. I am wondering if this is possible at all? Any ideas where I can get information about this? Thanks in advance Roberto

    Read the article

< Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >