Search Results

Search found 9280 results on 372 pages for 'wireless card'.

Page 67/372 | < Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >

• Ubuntu 12.04, can't find my home wifi network

  - by Anton

  I've tried several solutions I found on the web, but didn't manage to solve a problem. Since today my laptop won't find my WiFi network, but neighbours' networks are suggested. Another laptop with U12.04 does find one. What do I do? I've Dell Latitude-E4310, 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01) Subsystem: Dell Inspiron M5010 / XPS 8300 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f2c00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac also NetworkManager Tool State: connected (global) - Device: eth1 ----------------------------------------------------------------- Type: 802.11 WiFi Driver: wl State: disconnected Default: no HW Address: 1C:65:9D:7A:45:5C Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Should I provide anything else? Many thanks in advance.

  Read the article

• slow speed transfering files to a local network device

  - by F. Ariel Jung

  I'm having troubles copying files from my pc(ubuntu 13.04 64 bits) to a Media Center(WDTV Live: with an SATA2 HDD attached) through the local network. the speed is to slow, it's up to 2.0 MB/s image: http://s11.postimg.org/g1nuai92b/Captura_de_pantalla_de_2013_06_24_07_46_55.png (I don't use image tag because it is a big image) my PC has a wifi network card Tp Link TL-WN951N and it is connected to a TP Link TL-WDR3500 router via wifi, and the WDTV Live is connected via LAN here is a iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TL-WDR3500" Mode:Managed Frequency:2.462 GHz Access Point: A0:F3:C1:6C:3B:F1 Bit Rate=39 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:33521 Invalid misc:2245290 Missed beacon:0 if more data is required I'll post it as needed. I can't figure this out, needed help. please

  Read the article

• Nvidia Optimus shows Nvidia card is always active in Windows 8

  - by Ty Underwood

  I have loaded the new Asus Nvidia driver for my Asus Ux32VD that I have installed Windows 8 on. It has an Nvidia 620m and Intel hd 4000 integrated graphics. The problem is that the Optimus activity icon in my system tray shows that the Nvidia card is always active, though it shows that it is not doing anything. I can force the system to prefer the Intel graphics, and after rebooting, the Nvidia card will shut off, but then all the programs will be overridden and use the Intel graphics. Is anyone else having problems with Optimus in Windows 8? My battery life is really suffering because I'm always idling my Nvidia card while also presumably running the Intel card. Any suggestions would be appreciated.

  Read the article

• Wireless stopped working on Lenovo G430 notebook

  - by Jigar Shah

  It has Broadcom Wireless card. Wireless used to work fine earlier. Now it has stopped suddenly. I can see Wireless driver in "Hardware Driver" tab. How do i diagnose problem ? in ifconfig output, i don't see wlan0 at all. I am on Ubuntu 9.10.

  Read the article

• Restoring a SD card after using it to root a device

  - by Raz

  I recently purchased the Nook Touch reading device. I rooted it using the instructions on nookdevs.com Rooting included using win32diskimager to somehow transfer an .img file onto the card. Rooting is now completed and as far as I can tell, I don't need to keep the files used on the SD card, which has been reduced from a 3.5 GB or so unit to a 75 MB unit. Is there a simple way for me to somehow reformat the SD card to its original state or at least 3.5 GB. I cannot simply format it.

  Read the article

• How to install Netgear N-300 UAB adapter WNA3100 on Ubuntu 12.04

  - by JacobusR

  After a fresh install of Ubuntu 12.04, the first thing I'm trying to do, is to setup my wireless adapter. I can see it using lsusb: beer@beer-linux:~$ lsusb ... Bus 002 Device 006: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] ... I have found a lot of dated instructions on the net and just wanted to know what the right way is to set it up on 12.04. I don't want to mess up a brand new install by tweaking things that don't need tweaking. According to most posts, you have to install the Windows drivers using the ndiswrapper package. Is this still the right way to go? If so, it would be great if someone could write down the steps to do this under 12.04

  Read the article

• Wifi networks will not show up!

  - by Kcahmadi

  I'm running Ubuntu 14.04 on an old '08 macbook. I've gone to system settingsSoftware & UpdatesAdditional Drivers and enabled the wireless driver. But when I click the wifi icon on the top toolbar no networks show up. When running lshw it clearly shows my wireless card under Network controller and it says the driver is installed. However, nm-tool only shows ethernet. And rfkill only shows bluetooth. What can I do?

  Read the article

• Smart card driven membership and door entry system

  - by Rob G

  I'm looking at putting in a smart card driven system at my local sports club (which doesn't have oodles of money), and since they're willing to pay for hardware, and I'm willing to do the technical setup, I was wondering if anyone had any experience in setting something like this up. Writing any software needed is not the problem, I've pretty much got that covered with various open source projects out there and custom code I'll write, but it's more the hardware side I'm not too sure about and I'm looking for advice from people out there. I'm sure there are numerous complications, but on the surface it looks fairly simple. I'd basically like to enable members to swipe/touch a smart card at the door to gain entry to the club, walk up to a touch screen PC and swipe/touch a card reader there to "login" to the system I create, which will allow them to book club facilities etc. I may even want that same card to then activate things like lights or music when they enter the room they've booked. Pretty Eutopian I know, but still, we'd like to get as close as we can. As I said, the software shouldn't be a problem, and on the hardware side, so far I'm looking at: All in one touch screen PC running Windows 7 or Ubuntu USB card reader (not sure which one to buy) Smart Cards (again, never bought these before) Door/lighting hardware that could be triggered (not sure here either) If anyone has any advice on implementing something like this - especially the items I'm not sure about above, and of course anything I've missed out that's crucial, I'd be most grateful. Recommended hardware that you've used for something like this would be fantastic!

  Read the article

• System freeze after opening Wi-Fi menu can boot into the machine and use Internet in recovery mode

  - by Michael

  So right now sitting in front of my Alienware area 51 desktop. It has a Broadcom Netlink BCM 5784M gigabit ethernet PCI E card. Most of the time able to get through the login screen and to the main screen if I click on the wireless settings on the top right-hand corner the system immediately freezes the cursor does not move at all keyboards are unresponsive. I was doing some quick Google searching and I found a suggestion to boot into recovery mode I did this and did a apt-get Distribution update which ran successfully installed then I rebooted into the regular system same thing I'm pretty sure it's the network card because even if I don't click the settings if a network related dialog opens such as disconnection or connection the system again immediately freezes. I'm running Ubuntu 13.04 ** update 1 ** Just was able to use my system for a little bit however when I went into Firefox and hit the web it again froze so obviously a driver problem but I'm not sure how to get drivers for Broadcom which apparently according to the description on stack-overflow is terrible Any ideas? Sorry for lack of punctuation on an ipad.

  Read the article

• How do I get the Netgear N150 USB wifi adapter working on 12.04?

  - by Jon

  Just installed latest version of ubuntu. I'm using a Netgear N150 Wireless USB Micro Adapter WNA1000M which keeps asking for network password over and over. I read elsewhere that I needed to install the latest driver for my chipset (RTL8188CUS) which I have and still no joy. If I run the steps listed in this thread while connected through ethernet, the wireless will connect just fine. If I disconnect the ethernet, the wifi will even continue to work, but after a restart or two I will lose connection. If I repeat the steps listed in the aforementioned thread, it will not re-connect wifi unless I run those steps while connected to ethernet.......so strange...

  Read the article

• Cannot get Atheros AR9285 to work on 12.10

  - by user100449

  I've already went through all possible advices and still cannot start my Atheros AR9285 wireless card. I have a laptop Toshiba Portege Z830 where the WiFi already worked under Windows 7. But after migration on Ubuntu 12.10. I'm not able get it work. This is what I see on command lshw *-network UNCLAIMED description: Network controller product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:c0500000-c050ffff This is what I see on command rfkill list 0: Toshiba Bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 1: hci0: Bluetooth Soft blocked: yes Hard blocked: no Any idea?

  Read the article

• How to setup 802.11n wireless card in ubuntu

  - by michael

  Hi, I have installed ubuntu 9.10 on my laptop. It has a 802.11n wireless card. When I boot up to ubuntu, the wireless does not work. And if I connect to a wire network within ubuntu, it works. Can you please tell me how can I setup my wireless card in ubuntu 9.10? Thank you.

  Read the article

• Ops Center 12c - Update - Provisioning Solaris on x86 Using a Card-Based NIC

  - by scottdickson

  Last week, I posted a blog describing how to use Ops Center to provision Solaris over the network via a NIC on a card rather than the built-in NIC.  Really, that was all about how to install Solaris on a SPARC system.  This week, we'll look at how to do the same thing for an x86-based server. Really, the overall process is exactly the same, at least for Solaris 11, with only minor updates. We will focus on Solaris 11 for this blog.  Once I verify that the same approach works for Solaris 10, I will provide another update. Booting Solaris 11 on x86 Just as before, in order to configure the server for network boot across a card-based NIC, it is necessary to declare the asset to associate the additional MACs with the server.  You likely will need to access the server console via the ILOM to figure out the MAC and to get a good idea of the network instance number.  The simplest way to find both of these is to start a network boot using the desired NIC and see where it appears in the list of network interfaces and what MAC is used when it tries to boot.  Go to the ILOM for the server.  Reset the server and start the console.  When the BIOS loads, select the boot menu, usually with Ctrl-P.  This will give you a menu of devices to boot from, including all of the NICs.  Select the NIC you want to boot from.  Its position in the list is a good indication of what network number Solaris will give the device. In this case, we want to boot from the 5th interface (GB_4, net4).  Pick it and start the boot processes.  When it starts to boot, you will see the MAC address for the interface Once you have the network instance and the MAC, go through the same process of declaring the asset as in the SPARC case.  This associates the additional network interface with the server.. Creating an OS Provisioning Plan The simplest way to do the boot via an alternate interface on an x86 system is to do a manual boot.  Update the OS provisioning profile as in the SPARC case to reflect the fact that we are booting from a different interface.  Update, in this case, the network boot device to be GB_4/net4, or the device corresponding to your network instance number.  Configure the profile to support manual network boot by checking the box for manual boot in the OS Provisioning profile. Booting the System Once you have created a profile and plan to support booting from the additional NIC, we are ready to install the server. Again, from the ILOM, reset the system and start the console.  When the BIOS loads, select boot from the Boot Menu as above.  Select the network interface from the list as before and start the boot process.  When the grub bootloader loads, the default boot image is the Solaris Text Installer.  On the grub menu, select Automated Installer and Ops Center takes over from there. Lessons The key lesson from all of this is that Ops Center is a valuable tool for provisioning servers whether they are connected via built-in network interfaces or via high-speed NICs on cards.  This is great news for modern datacenters using converged network infrastructures.  The process works for both SPARC and x86 Solaris installations.  And it's easy and repeatable.

  Read the article

• Network Manager troubleshooting

  - by Anero

  I'm having some issues when connecting to my house's wifi from my Ubuntu 10.10 laptop. If the connection doesn't exists, when selecting the network (and after entering the WPA2 password) I'm able to connect. Once the connection is saved, when trying to reconnect, Network Manager works for a minute or so and then fails; the only way to reconnect then is to delete the saved connection and re-select the network from the list of available wireless networks. The same network works with no issues on the same laptop when running Win7, and on other wireless networks when running Ubuntu. Is there a Network Manager log which I can take a look at for troubleshooting the issue? Are there any tools for checking the wifi status?

  Read the article

• Unstable Wifi and Spontaneous Low-graphic Error with Pavilion DV4

  - by Constant Dean

  I've been having numerous problems with connectivity through WiFi. It had been working for a few days and now it doesn't. On top of that around 40% of every time I turn on the laptop it shows "System running in low-graphics" error and I'm unable to view the desktop (sometimes not even able to access terminal), therefore having to manually power-down until it finally works. I use Ubuntu 12.10. nm-tool NetworkManager Tool State: connected (global) - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: r8169 State: connected Default: yes HW Address: 84:34:97:6B:2E:D7 Capabilities: Carrier Detect: yes Speed: 10 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.10 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 DNS: 68.237.161.12 - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: rt2800pci State: unavailable Default: no HW Address: 68:94:23:50:A5:D9 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points

  Read the article

• Ubuntu 12.04 crashes on startup for newer versions of Linux, possibly related to WiFi

  - by Jake

  My computer gets to the screen with the Ubuntu logo and the orange/white dots, and then the screen goes black, spits out a lot of error messages, and cannot boot. (If it'd be helpful, I can take a photo of my screen in this state.) I've found I can successfully boot if my wireless card is turned off. As soon as I turn it on, my computer crashes with the same black screen of death. I can also successfully boot if I choose "Previous Linux Version" and select a few versions back (I think 3.0.6). Here are some relevant details about my setup: Ubuntu 12.04 Computer: Lenovo x230 Wireless: Realtek RTL8188CE 802.11b/g/n WiFi Adapter Processor: Intel Core i5-3210M CPU @ 2.50GHz × 4 RAM: 16 GB of RAM Thank you!!!

  Read the article

• What does a media server need?

  - by DeaDSouL

  I want to buy a new PC to be used as a media server that streams HD movies, music to any wireless device on my network (laptop, desktop, TV, etc.). I was wondering about the PC hardware's specifications that I need to have so that it can work just fine? (It will be wireless) Is there any tutorial showing how it could be done? And the security - how can I secure it? As well as I need it to to host my emails. I mean I have many emails. And sometimes I'm using desktop, sometimes laptop.. so is it possible to make the server store a copy of my emails, attachments, all sent items (whether they were from desktop or laptop)?

  Read the article

• How to fix additional STA driver installation error on 12.04

  - by nibl

  I have a Broadcom BCM4313 wireless driver. It worked fine under 11.04 and the upgrade to 11.10 also went smoothly. The 12.04 upgrade has broken the wireless connection. I've seen several posts about this and all presume you can activate the STA drivers, but that's where it fails on this machine. The log is in /var/log/jockey.log: WARNING: modinfo for module wl failed: ERROR: modinfo: could not find module wl WARNING: /sys/module/wl/drivers does not exist, cannot rebind wl driver DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted (repeat of last error several times) Any ideas how to proceed?

  Read the article

• Where are Wireless Profiles stored in Ubuntu

  - by LonnieBest

  Where does Ubuntu store profiles that allow it to remember the credentials to private wireless networks that it has previously authenticate to and used? I just replaced my Uncle's hard drive with a new one and installed Ubuntu 10.04 on it (he had Ubuntu 9.10 on his old hard drive. He is at my house right now, and I want him to be able to access his private wireless network when he gets home. Usually, when I upgrade Ubuntu, I have his /home directory on another partition, so his wireless profile to his own network persists. However, right now, I'm trying to figure out which .folder I need to copy from his /home/user folder on the old hard drive, to the new hard drive, so that he will be able to have wireless Internet when he gets home. Does anyone know with certainty, exactly which folder I need to copy to the new hard drive to achieve this?

  Read the article

• Wi-Fi Connection Issues.. tried a lot.. pls help

  - by nikvana

  I am posting a question for the first time, do not know coding and am relatively new to ubuntu, but a quick learner. I have an Acer Aspire One D270 notebook that came originally with Windows 7 starter installed. I have removed that and installed Ubuntu 12.04 I have chronic issues with connecting to the wi-fi. I figure it is due to issues with the driver(s) I think this is the driver I have- BCM4313 802.11bgn Wireless Network Adapter (on entering this in the terminal- lshw -C) I also installed the software Windows wireless drivers and it shows currently installed drivers as blank- but when i choose install new drivers, it asks me to select inf file which I do not know where to find. Please help with this, coders. Thanks a ton

  Read the article

• Concurrent wireless and wired network

  - by Stew Megaw

  Hi, I am concerned with maintaining a wireless and wired network connection on my laptop. Basically I can change the metric on each interface so that Windows prefers one connection over the other. I am wondering is following scenario possible.... Some applications uses the wireless while other applications use the wired... I want Internet Explorer (only) to use the wireless connection while Outlook and everything else uses the wired connection. Perhaps adding some lines to the routing table might work? - Adding the ip addresses of websites I want to view via the wireless connection? Many Thanks in advance for any replies!

  Read the article

• Error Formatting Memory Card

  - by Kirby Fromm

  I just tried to look at some of my pictures on my sony cyber-shot dsc-tx5, with a Lexar platinum II 16 GB memory stick, and it is now saying I have a formatting error every time I turn the camera on. The card and Camera are both 3 months old and have worked perfectly before. I tried to check the card on my computer and it says there is an error, so the camera is working but the card is not. Does anyone know how I can fix this to get the pictures off of the card?

  Read the article

• Network card dies when trying to wake up laptop from sleep

  - by Bugmaster

  I have a Dell XPS 1640 laptop (aka Dell Studio XPS 16), running Vista. Whenever the laptop wakes up from sleep, my Broadcomm LAN card immediately dies. Any attempt to access it completely locks up whichever program I use to access it. There appears to be no way to re-awaken the card, other than rebooting; note that Vista does not even shut down properly if some program is waiting for the card. So far, I have tried the following: Disabled the "allow your computer to shut down this device to save power" in the device properties. This had no effect. Attempted to disable and then enable the card in the device properties. No effect. Tried ipconfig /renew: this locks up ipconfig to the point where I can't even kill its process. Force-install updated drivers from broadcomm: no effect. Does anyone have any other ideas ?

  Read the article

• Wifi worked after reinstalling the driver, but why did it stopped working in the first place?

  - by Ankit

  I was having an issue with connecting to my wifi router since yesterday; could see the router in the wireless networks available but the router was not authenticating my password. I tried unblocking the hardware switches though non was blocked. Finally on discussing with the ISP i gave a re-installation of the wireless driver a try; and to my surprise that worked.(I was assuming faulty wifi router). So as per the subject of the question; I am very curious to know what actually happened that prevented me to connect to my wifi. Any logs that I could see to confirm the cause of this suspicious activity.

  Read the article

• Issues in Fedora detecting on board NIC card

  - by Vivek27

  Basically I have two NIC cards (on-board + Added in PCI slot) on my Linux machine running Fedora 12.By default the OS detects the NIC card in the PCI slot but it fails to detect the on board network card.Following are few details of the same Linux Vivek 2.6.32.26-175.fc12.i686.PAE #1 SMP Wed Dec 1 21:45:50 UTC 2010 i686 i686 i386 GNU/Linux ifconfig -a doesen't show the on board NIC card.Any thoughts for it please? Since it is also related to network configuration. I posted it here.

  Read the article

< Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >