Search Results

Search found 1812 results on 73 pages for 'amd radeon'.

Page 69/73 | < Previous Page | 65 66 67 68 69 70 71 72 73  | Next Page >

• transferring binary files between systems

  - by tim

  Hi guys I'm trying to transfer my files between 2 UNIX clusters, the data is pure numeric (vectors of double) in binary form. Unfortunately one of the systems is IBM ppc997 and the other is AMD Opteron, It seems the format of binary numbers in these systems are different. I have tried 3 ways till now: 1- Changed my files to ASCII format (i.e. saved a number at each line in a text file), sent them to the destination and changed them again to binary on the target system (they both are UNIX, no end of line character difference??!) 2- Sent pure binaries to the destination 3- used uuencode sent them to the destination and decoded them Unfortunately any of these methods does not work (my code in the destination system generates garbage, while it works on the first system, I'm 100% sure the code itself is portable). I don't know what else I can do? Do you have any idea? I'm not a professional, please don't use computer scientists terminology! And: my codes are in C, so by binary I mean a one to one mapping between memory and hard disk. Thanks

  Read the article

• CPU overheating because of Delphi IDE

  - by Altar

  I am using Delphi 7 but I have trialed the Delphi 2005 - 2010 versions. In all these new versions my CPU utilization is 50% (one core is 100%, the other is "relaxed") when Delphi IDE is visible on screen. It doesn't happen when the IDE is minimized. My computer is overheating because of this. Any hints why this happens? It looks like if I want to upgrade to Delphi 2010, I need to upgrade my cooling system first. And I am a bit lazy about that, especially that I want to discahrge my computer and buy a new one (in the next 6 months) - probably I will have to buy a Win 7 license too. Edit: My CPU is AMD Dual Core 4600+. 4GB RAM Overheating means that temperature of the HDDs is raising because the CPU. Edit: Comming to a possible solution I just deleted all HKCU/CodeGear key and let started Delphi as "new". Guess what? The CPU utilization is 0%. I will investigate more.

  Read the article

• Aliasing `T*` with `char*` is allowed. Is it also allowed the other way around?

  - by StackedCrooked

  Note: This question has been renamed and reduced to make it more focused and readable. Most of the comments refer to the old text. According to the standard objects of different type may not share the same memory location. So this would not be legal: int i = 0; short * s = reinterpret_cast<short*>(&i); // BAD! The standard however allows an exception to this rule: any object may be accessed through a pointer to char or unsigned char: int i = 0; char * c = reinterpret_cast<char*>(&i); // OK However, it is not clear to me if this is also allowed the other way around. For example: char * c = read_socket(...); unsigned * u = reinterpret_cast<unsigned*>(c); // huh? Summary of the answers The answer is NO for two reasons: You an only access an existing object as char*. There is no object in my sample code, only a byte buffer. The pointer address may not have the right alignment for the target object. In that case dereferencing it would result in undefined behavior. On the Intel and AMD platforms it will result performance overhead. On ARM it will trigger a CPU trap and your program will be terminated! This is a simplified explanation. For more detailed information see answers by @Luc Danton, @Cheers and hth. - Alf and @David Rodríguez.

  Read the article

• Strange ATI vs Nvidia TRIANGLE_STRIP issue

  - by chriscisco

  I have this code, I am using a test for my Engine I am working on. On My NVIDIA NVS 4200M it displays the GL_TRIANGLE_STRIP as expected. On my ATI Radeon 5800 it appears to draw a Triangle. shader.begin(); Matrix4<float> temp = getActiveCamera()->getProjectionMatrix() * getActiveCamera()->getObjectToWorld().fastInverse(); glUniformMatrix4fv(shader["mvp"], 1, GL_TRUE, temp.getArray()); glBegin(GL_TRIANGLE_STRIP); glVertexAttrib3f(shader["colour"],0,1,0); glVertexAttrib3f(shader["coord3d"],-.5,-.5,0); glVertexAttrib3f(shader["colour"],1,1,0); glVertexAttrib3f(shader["coord3d"],0.5,-.5,0); glVertexAttrib3f(shader["colour"],1,0,1); glVertexAttrib3f(shader["coord3d"],-.5,.5,0); glVertexAttrib3f(shader["colour"],0,1,1); glVertexAttrib3f(shader["coord3d"],.5,.5,0); glEnd(); shader.end(); Here are what it actually looks like on my two computers. https://www.dropbox.com/s/sgm2j978tx2ipnp/not%20working.png https://www.dropbox.com/s/27idv0b8k0p4pcx/working.png

  Read the article

• Windows XP SP3 - Library not registered error... IE8 not installing.

  - by Wesley

  Specs to put things in context: AMD Athlon XP 2400+ @ 1987 MHz / 2 x 512MB PC3200 DDR RAM / WD 160GB IDE HDD / 3DFuzion 128MB GeForce 6200 AGP 4x / FIC AM37 / Windows XP SP3 Just recently, I was unable to start Windows Media Player. I clicked it and the busy cursor came up, but then nothing happened. Also, I tried doing a search for a file, and same thing. It would show busy cursor then suddenly stop doing anything. I couldn't find it in the Processes of the Task Manager. (Perhaps I don't know what I'm looking for?) Also, I was trying to update my DirectX, which has been running something older than DX9 9.0c for a while now, except the installation fails due to "internal error". I think the failed DirectX installation has been like that for a while... (I remember trying to install DX9 9.0c a while back, but still failed.) The Windows programs not starting, I don't think I've ever had before... what could be the cause of these problems?! Thanks in advance. =) EDIT1: Weird thing now is that when I try to open User Accounts, I get a message saying "Wrong number of arguments or invalid property assignment." Also, when I'm trying to open services.msc, I'm getting a script error that says that "Library not registered." (Code: 0, URL: res://C:\WINDOWS\System32\mmcndmgr.dll/views.htm) Perhaps this is related to my other question, where I seemed to have an unregistered library of some sort. EDIT2: The DirectX End-User Runtime Web Installer freakishly worked and updated successfully. Now, I have focussed the question on the bigger problem. For WMP11, H&S, and Search, I click it once, get a busy icon for a second, and then nothing happens. Refer to EDIT1 for other problems. EDIT3: Seems that my problems may be related to some Internet Explorer Script Errors. So what I did was download the IE8 installer from the Microsoft website, but when I run it and get to the main portion of the installer, it just keeps looping on the Downloading step of the installation. The installer is still running, but I left it for at least 4 hours and the downloading step was still not finished. What is the problem? Also, I uninstalled Ubuntu 9.10 after these problems, but they still remain. EDIT4: I'm getting an active desktop recovery background on startup now. And within seconds my computer hangs again. EDIT3 explains main issue though.

  Read the article

• iSCSI timeouts under high load

  - by Antonio

  I have two servers connected via Gigabit Ethernet. One is iSCSI target, the second one is initiator. When I run mkfs.ext4 at initiator, after a while disk IO slows down critically. In the target host I can see the following in syslog: Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119668c 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119668c 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119668d 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119668d 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119668e 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119668e 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 1196696 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 1196696 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119669e 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119669e 6 Sep 14 09:40:04 sh11 tgtd: abort_task_set(1139) found 119669f 0 Sep 14 09:40:04 sh11 tgtd: abort_cmd(1115) found 119669f 6 And load average grows to 12 or even more: # uptime 12:37:00 up 23 days, 13:25, 1 user, load average: 12.00, 7.00, 4.00 CentOS 6.3 tgtd 1.0.24 Intel Pentium 4 2.4GHz 1Gb RAM 2Tb WD Cavlar Green SATA 2.0 #lspci 00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 02) 00:01.0 PCI bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE Host-to-AGP Bridge (rev 02) 00:1d.0 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 82) 00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 02) 00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 02) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV200 QW [Radeon 7500] 02:01.0 Ethernet controller: D-Link System Inc DGE-530T Gigabit Ethernet Adapter (rev 11) (rev 11) 02:02.0 RAID bus controller: VIA Technologies, Inc. VT6421 IDE/SATA Controller (rev 50) 02:03.0 RAID bus controller: VIA Technologies, Inc. VT6421 IDE/SATA Controller (rev 50) 02:04.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) 02:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VE (CNR) Ethernet Controller (rev 82) Is there a way to tune target host to avoid these timeouts?

  Read the article

• XenServer 6.0.2 path to installation media contains non-ascii characters

  - by cmaduro

  XenServer 6.0.2 install fails no matter what I do. I have confirmed that the md5 checksum on my ISO file is good. I tried installing from a mounted ISO file (remotely via iKVM). I tried installing from physical media. I tried installing from a bootable USB stick (using syslinux + contents of the ISO) All attempts have yielded the same result: When verifying the installation media, at 0% initializing, the following is reported: "Some packages appeared to be damaged." followed by a list of pretty much all the gz2 and rpm packages. If I skip the media verification the installer proceeds and then gives me an error when it reaches "Installing from base pack" at 0% which states "An unrecoverable error has occurred. The error was: 'ascii' codec can't decode byte 0xff in position 20710: ordinal not in range(128) Please refer to your user guide, or contact a Technical Support Representative, for further details" there is one option left which is to reboot. Apparently at some point during the processing of the repositories on the installation media non-ascii characters are found, which causes the installer to quit. How do I fix this? Here are my specs TYAN S8236 motherboard 2 AMD Opteron 6234 processors LSI2008 card connected to 2 1TB Seagate Constellation drives SATA, 1 500GB Corsair m4 SSD SATA and 1 Corsair Forse 3 - 64GB SSD SATA Onboard SATA connected to a slim DVD-+RW. Onboard SAS connected to 2 IBM ESX 70GB 10K SAS drives (for XenServer) 256GB memory ================================================================================= Comments: According to pylonsbook.com "chances are you have run into a problem with character sets, encodings, and Unicode" – cmaduro 10 hours ago A clue is provided by "vmware.com/support/vsphere5/doc/…; Data migration fails if the path to the vCenter Server installation media contains non-ASCII characters When this problem occurs, an error message similar to: 'ascii' codec can't decode byte 0xd0 in position 30: ordinal not in range(128) appears, and the installer quits unexpectedly during the data migration process. – cmaduro 10 hours ago This is an error that python throws. And guess what, the .py extention of the file you have to edit in this link community.spiceworks.com/how_to/show/1168 means the installer is written in python. Python is interpreted, so now to find the install file responsible for this error. – cmaduro 6 hours ago The file that generates the error upon verification is /opt/xensource/installer/tui/repo.py. The error message appears around line 359. – cmaduro 2 hours ago I am fairly sure that the install error is generated somewhere in repository.py as the backend.py file throws errors while methods in that file are being called. Perhaps all errors can be traced back to this file. – cmaduro 1 hour ago

  Read the article

• Apache2 benchmarks - very poor performance

  - by andrzejp

  I have two servers on which I test the configuration of apache2. The first server: 4GB of RAM, AMD Athlon (tm) 64 X2 Dual Core Processor 5600 + Apache 2.2.3, mod_php, mpm prefork: Settings: Timeout 100 KeepAlive On MaxKeepAliveRequests 150 KeepAliveTimeout 4 <IfModule Mpm_prefork_module> StartServers 7 MinSpareServers 15 MaxSpareServers 30 MaxClients 250 MaxRequestsPerChild 2000 </ IfModule> Compiled in modules: core.c mod_log_config.c mod_logio.c prefork.c http_core.c mod_so.c Second server: 8GB of RAM, Intel (R) Core (TM) i7 CPU [email protected] Apache 2.2.9, **fcgid, mpm worker, suexec** PHP scripts are running via fcgi-wrapper Settings: Timeout 100 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 4 <IfModule Mpm_worker_module> StartServers 10 MaxClients 200 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 1000 </ IfModule> Compiled in modules: core.c mod_log_config.c mod_logio.c worker.c http_core.c mod_so.c The following test results, which are very strange! New server (dynamic content - php via fcgid+suexec): Server Software: Apache/2.2.9 Server Hostname: XXXXXXXX Server Port: 80 Document Path: XXXXXXX Document Length: 179512 bytes Concurrency Level: 10 Time taken for tests: 0.26276 seconds Complete requests: 1000 Failed requests: 0 Total transferred: 179935000 bytes HTML transferred: 179512000 bytes Requests per second: 38.06 Transfer rate: 6847.88 kb/s received Connnection Times (ms) min avg max Connect: 2 4 54 Processing: 161 257 449 Total: 163 261 503 Old server (dynamic content - mod_php): Server Software: Apache/2.2.3 Server Hostname: XXXXXX Server Port: 80 Document Path: XXXXXX Document Length: 187537 bytes Concurrency Level: 10 Time taken for tests: 173.073 seconds Complete requests: 1000 Failed requests: 22 (Connect: 0, Length: 22, Exceptions: 0) Total transferred: 188003372 bytes HTML transferred: 187546372 bytes Requests per second: 5777.91 Transfer rate: 1086267.40 kb/s received Connnection Times (ms) min avg max Connect: 3 3 28 Processing: 298 1724 26615 Total: 301 1727 26643 Old server: Static content (jpg file) Server Software: Apache/2.2.3 Server Hostname: xxxxxxxxx Server Port: 80 Document Path: /images/top2.gif Document Length: 40486 bytes Concurrency Level: 100 Time taken for tests: 3.558 seconds Complete requests: 1000 Failed requests: 0 Write errors: 0 Total transferred: 40864400 bytes HTML transferred: 40557482 bytes Requests per second: 281.09 [#/sec] (mean) Time per request: 355.753 [ms] (mean) Time per request: 3.558 [ms] (mean, across all concurrent requests) Transfer rate: 11217.51 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 3 11 4.5 12 23 Processing: 40 329 61.4 339 1009 Waiting: 6 282 55.2 293 737 Total: 43 340 63.0 351 1020 New server - static content (jpg file) Server Software: Apache/2.2.9 Server Hostname: XXXXX Server Port: 80 Document Path: /images/top2.gif Document Length: 40486 bytes Concurrency Level: 100 Time taken for tests: 3.571531 seconds Complete requests: 1000 Failed requests: 0 Write errors: 0 Total transferred: 41282792 bytes HTML transferred: 41030080 bytes Requests per second: 279.99 [#/sec] (mean) Time per request: 357.153 [ms] (mean) Time per request: 3.572 [ms] (mean, across all concurrent requests) Transfer rate: 11287.88 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 2 63 24.8 66 119 Processing: 124 278 31.8 282 391 Waiting: 3 70 28.5 66 164 Total: 126 341 35.9 350 443 I noticed that in the apache error.log is a lot of entries: [notice] mod_fcgid: call /www/XXXXX/public_html/forum/index.php with wrapper /www/php-fcgi-scripts/XXXXXX/php-fcgi-starter What I have omitted, or do not understand? Such a difference in requests per second? Is it possible? What could be the cause?

  Read the article

• High CPU from httpd process

  - by KHWeb

  I am currently getting high CPU on a server that is just running a couple of sites with very low traffic. One of the sites is in still development going live soon. However, this site is very very slow...When browsing through its pages I can see that the CPU goes from 30% to 100% for httpd (see top output below). I have tuned httpd & MySQL, Apache Solr, Tomcat for high performance, and I am using APC. Not sure what to do from here or how to find the culprit as I have a bunch of messages on the httpd log and have been chasing dead ends for some time...any help is greatly appreciated. Server: AuthenticAMD, Quad-Core AMD Opteron(tm) Processor 2352, RAM 16GB Linux 2.6.27 64-bit, Centos 5.5 Plesk 9.5.4, MySQL 5.1.48, PHP 5.2.17 Apache/2.2.3 (CentOS) DAV/2 mod_jk/1.2.15 mod_ssl/2.2.3 OpenSSL/0.9.8e-fips-rhel5 PHP/5.2.17 mod_perl/2.0.4 Perl/v5.8.8 Tomcat6-6.0.29-1.jpp5, Tomcat-native-1.1.20-1.el5, Apache Solr top 17595 apache 20 0 1825m 507m 10m R 100.4 3.2 0:17.50 httpd 17596 apache 20 0 1565m 247m 9936 R 83.1 1.5 0:10.86 httpd 17598 apache 20 0 1430m 110m 6472 S 54.5 0.7 0:08.66 httpd 17599 apache 20 0 1438m 124m 12m S 37.2 0.8 0:11.20 httpd 16197 mysql 20 0 13.0g 2.0g 5440 S 9.6 12.6 297:12.79 mysqld 17617 root 20 0 12748 1172 812 R 0.7 0.0 0:00.88 top 8169 tomcat 20 0 4613m 268m 6056 S 0.3 1.7 6:40.56 java httpd error_log [debug] prefork.c(991): AcceptMutex: sysvsem (default: sysvsem) [info] mod_fcgid: Process manager 17593 started [debug] proxy_util.c(1854): proxy: grabbed scoreboard slot 0 in child 17594 for worker proxy:reverse [debug] proxy_util.c(1967): proxy: initialized single connection worker 0 in child 17594 for (*) [debug] proxy_util.c(1854): proxy: grabbed scoreboard slot 0 in child 17595 for worker proxy:reverse [debug] proxy_util.c(1873): proxy: worker proxy:reverse already initialized [notice] child pid 22782 exit signal Segmentation fault (11) [error] (43)Identifier removed: apr_global_mutex_lock(jk_log_lock) failed [debug] util_ldap.c(2021): LDAP merging Shared Cache conf: shm=0x7fd29a5478c0 rmm=0x7fd29a547918 for VHOST: example.com [info] APR LDAP: Built with OpenLDAP LDAP SDK [info] LDAP: SSL support available [info] Init: Seeding PRNG with 256 bytes of entropy [info] Init: Generating temporary RSA private keys (512/1024 bits) [info] Init: Generating temporary DH parameters (512/1024 bits) [debug] ssl_scache_shmcb.c(374): shmcb_init allocated 512000 bytes of shared memory [debug] ssl_scache_shmcb.c(554): entered shmcb_init_memory() [debug] ssl_scache_shmcb.c(576): for 512000 bytes, recommending 4265 indexes [debug] ssl_scache_shmcb.c(619): shmcb_init_memory choices follow [debug] ssl_scache_shmcb.c(621): division_mask = 0x1F [debug] ssl_scache_shmcb.c(623): division_offset = 96 [debug] ssl_scache_shmcb.c(625): division_size = 15997 [debug] ssl_scache_shmcb.c(627): queue_size = 2136 [debug] ssl_scache_shmcb.c(629): index_num = 133 [debug] ssl_scache_shmcb.c(631): index_offset = 8 [debug] ssl_scache_shmcb.c(633): index_size = 16 [debug] ssl_scache_shmcb.c(635): cache_data_offset = 8 [debug] ssl_scache_shmcb.c(637): cache_data_size = 13853 [debug] ssl_scache_shmcb.c(650): leaving shmcb_init_memory()

  Read the article

• Using a 64bit Linux kernel, can't see more than 4GB of RAM in /proc/meminfo

  - by Chris Huang-Leaver

  I'm running my new computer which has 8GB of RAM installed, which is visable from BIOS page, does not show in /proc/meminfo uname -a Linux localhost 3.0.6-gentoo #2 SMP PREEMPT Sat Nov 19 10:45:22 GMT-- x86_64 AMD Phenom(tm) II X4 955 Processor AuthenticAMD GNU/Linux The result of /proc/meminfo is as follows: (thans Andrey) MemTotal: 4021348 kB MemFree: 1440280 kB Buffers: 23696 kB Cached: 1710828 kB SwapCached: 4956 kB Active: 1389904 kB Inactive: 841364 kB Active(anon): 1337812 kB Inactive(anon): 714060 kB Active(file): 52092 kB Inactive(file): 127304 kB Unevictable: 32 kB Mlocked: 32 kB SwapTotal: 8388604 kB SwapFree: 8047900 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 492732 kB Mapped: 47528 kB Shmem: 1555120 kB Slab: 267724 kB SReclaimable: 177464 kB SUnreclaim: 90260 kB KernelStack: 1176 kB PageTables: 12148 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 10399276 kB Committed_AS: 3293896 kB VmallocTotal: 34359738367 kB VmallocUsed: 317008 kB VmallocChunk: 34359398908 kB AnonHugePages: 120832 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 23552 kB DirectMap2M: 3088384 kB DirectMap1G: 1048576 kB I have tried using mem=8G as a kernel boot parameter, I read a post about setting HIGHMEM64G to yes, before realising that only applies to 32bit kernels. Trying dmindecode -t memory SMBIOS 2.7 present. Handle 0x0026, DMI type 16, 23 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: Multi-bit ECC Maximum Capacity: 32 GB Error Information Handle: Not Provided Number Of Devices: 4 Handle 0x0028, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 4096 MB Form Factor: DIMM Set: None Locator: DIMM0 Bank Locator: BANK0 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz Manufacturer: Manufacturer0 Serial Number: SerNum0 Asset Tag: AssetTagNum0 Part Number: Array1_PartNumber0 Rank: Unknown Handle 0x002A, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: Unknown Data Width: 64 bits Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM1 Bank Locator: BANK1 Type: Unknown Type Detail: Synchronous Speed: Unknown Manufacturer: Manufacturer1 Serial Number: SerNum1 Asset Tag: AssetTagNum1 Part Number: Array1_PartNumber1 Rank: Unknown Handle 0x002C, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 4096 MB Form Factor: DIMM Set: None Locator: DIMM2 Bank Locator: BANK2 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz Manufacturer: Manufacturer2 Serial Number: SerNum2 Asset Tag: AssetTagNum2 Part Number: Array1_PartNumber2 Rank: Unknown Handle 0x002E, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: Unknown Data Width: 64 bits Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM3 Bank Locator: BANK3 Type: Unknown Type Detail: Synchronous Speed: Unknown Manufacturer: Manufacturer3 Serial Number: SerNum3 Asset Tag: AssetTagNum3 Part Number: Array1_PartNumber3 Rank: Unknown

  Read the article

• HT Link Sync Error after Ubuntu 10.04 LTS Installation

  - by marklab

  Update 1 I just assembled an exact replica of this server, and successfully installed Ubuntu 10.04 LTS in a RAID10 configuration. The success was confirmed by a login to the initial account. There must be a hardware component that is faulty. Since the error mentions HT, which I believe to be Hyper Threading, I will start with the CPUs. Please indicate if this error is more strongly associated with any other piece of hardware. Or make a recommendation of another approach that would be good for this issue. Issue I was attempting to install Ubuntu 10.04 LTS on this system with the board RAID10 configured. However, the installation failed at the partitioning stage by rebooting the system. Upon reboot, there is an error report after POST listing the following: Node0: NB WatchDog Timer Error Node1: HT Link Sync Error Node2: HT Link Sync Error ... Node7: HT Link Sync Error Press F1 to continue/resume. After pressing F1 the system will boot from the Ubuntu 10.04 LTS installation disc. However, it will fail at the same stage, and go through the same process from there. Hardware CPU: AMD OPTERON X12 6172 G34 2.1G 18MB Motherboard: Supermicro H8QG6-F HDD: WD Caviar Green 2TB 5.4K RPM Troubleshooting I disabled RAID10 on the system, and installed the Ubuntu on a single drive. It installed successfully. I then went back to a RAID10 setup and attempted to install on the system again, and was able to make it through the partitioning stage. However, upon reboot, the system reported: Error: file not found, and then booted me into the Grub Rescue console. I feel I have aggravated the problem at this point because when I attempted to install from the boot disc again, the system reboots upon hitting enter to even start the installation process. It does the same thing when trying to boot from an Ubuntu 11 disc. I have not been able to find any information on this HT Link Sync Error, which I feel may have started the problems I am experiencing now with the installation of the OS. I am also aware that Ubuntu is said not to be supported by the motherboard according to Supermicro's site. However, since I was able to install it successfully on a single drive, I do not believe it is incompatible. I would like to know a reason for why it's failing to install on/off.

  Read the article

• Android emulator performance on linux

  - by Rado

  I installed the android SDK and eclipse plugin on my laptop, but I was surprised to find out that the emulator eats up 100% of one of my cpu cores. I have exactly the same setup on a desktop machine that does not have this issue. Both computers are running arch linux and both were updated yesterday. Granted, the desktop has better hardware than the laptop, but I was expecting to get closer to 50% cpu usage than 100% on the laptop. Both android virtual devices have the same specs: CPU: ARM Target: Android 2.3.3 - API Level 10 Skin: WVGA800 SD Card: 512M hw.lcd.density: 240 vm.heapSize: 24 hw.ramSize: 256 Laptop host has Intel Core 2 T7200 @ 2GHz cpu with 2Gb RAM. Desktop host has AMD Phenom II X4 940 @ 3GHz cpu with 8Gb RAM. The android emulator uses only 1 core and here are the CPU usage results: Laptop: Cpu0 : 22.8%us, 76.5%sy, 0.0%ni, 0.3%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu1 : 11.2%us, 2.4%sy, 0.0%ni, 86.4%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 2055484k total, 1860304k used, 195180k free, 5276k buffers Swap: 2000088k total, 106872k used, 1893216k free, 350780k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2026 xyz 20 0 396m 207m 7192 R 100 10.3 4:11.58 emulator-arm Desktop: Cpu0 : 0.7%us, 0.0%sy, 0.0%ni, 99.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 1.3%us, 0.0%sy, 0.0%ni, 98.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 5.0%us, 1.3%sy, 0.0%ni, 91.9%id, 1.7%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 0.3%us, 0.3%sy, 0.0%ni, 99.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 7666324k total, 6506808k used, 1159516k free, 1650960k buffers Swap: 8988348k total, 0k used, 8988348k free, 2867300k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2811 xyz 20 0 392m 220m 6276 S 8 2.9 0:33.58 emulator-arm Is there any way I can improve the emulator performance on the laptop? [UPDATE] I ran the emulator with the same settings, on the same laptop under Win7 and after starting up, it didn't use 100% of a CPU core unlike under linux. Also, I tried running the emulator from a terminal in Linux and I get this message when I don't get it under the desktop Linux host: Could not configure '/dev/hpet' to have a 1024Hz timer. This is not a fatal error, but for better emulation accuracy type: 'echo 1024 /proc/sys/dev/hpet/max-user-freq' as root. I'm not really familiar with rtc or hpet, but it doesn't seem that max-user-freq setting does anything, I still get the same warning.

  Read the article

• Why do I see a large performance hit with DRBD?

  - by BHS

  I see a much larger performance hit with DRBD than their user manual says I should get. I'm using DRBD 8.3.7 (Fedora 13 RPMs). I've setup a DRBD test and measured throughput of disk and network without DRBD: dd if=/dev/zero of=/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 4.62985 s, 116 MB/s / is a logical volume on the disk I'm testing with, mounted without DRBD iperf: [ 4] 0.0-10.0 sec 1.10 GBytes 941 Mbits/sec According to Throughput overhead expectations, the bottleneck would be whichever is slower, the network or the disk and DRBD should have an overhead of 3%. In my case network and I/O seem to be pretty evenly matched. It sounds like I should be able to get around 100 MB/s. So, with the raw drbd device, I get dd if=/dev/zero of=/dev/drbd2 bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 6.61362 s, 81.2 MB/s which is slower than I would expect. Then, once I format the device with ext4, I get dd if=/dev/zero of=/mnt/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 9.60918 s, 55.9 MB/s This doesn't seem right. There must be some other factor playing into this that I'm not aware of. global_common.conf global { usage-count yes; } common { protocol C; } syncer { al-extents 1801; rate 33M; } data_mirror.res resource data_mirror { device /dev/drbd1; disk /dev/sdb1; meta-disk internal; on cluster1 { address 192.168.33.10:7789; } on cluster2 { address 192.168.33.12:7789; } } For the hardware I have two identical machines: 6 GB RAM Quad core AMD Phenom 3.2Ghz Motherboard SATA controller 7200 RPM 64MB cache 1TB WD drive The network is 1Gb connected via a switch. I know that a direct connection is recommended, but could it make this much of a difference? Edited I just tried monitoring the bandwidth used to try to see what's happening. I used ibmonitor and measured average bandwidth while I ran the dd test 10 times. I got: avg ~450Mbits writing to ext4 avg ~800Mbits writing to raw device It looks like with ext4, drbd is using about half the bandwidth it uses with the raw device so there's a bottleneck that is not the network.

  Read the article

• OCZ Vertex 2 not recognized by Ubuntu installer

  - by Zsub

  As I boot into the Ubuntu 10.10 (or 11.04, doesn't matter) live environment or installer, it just refuses to recognise my Vertex 2. It reports the disk as ATA and not supporting smart, shows no serial number, and doesn't list the size correctly. All fdisk tells me is Unable to read /dev/sda (it's the only storage in the PC). I'm now running a temporary install of Windows 7 off of it, which worked like a charm, so where am I going wrong with Ubuntu... Specs: Asus M4N68T-M LE V2 (BIOS 0702, most recent) OCZ Vertex 2 SSD 60 GB Amd Athlon II X4 640 Patriot PSD34G13332 4GB DDR3 ram (two banks) EDIT I installed a second drive, installed Ubuntu on that and booted, it recognised the SSD just fine. I'm now trying to apt-get upgrade the live-environment. I wonder if there is any way to sort of install Ubuntu from Ubuntu (I boot into the working install on the other drive, install it on the SSD and then boot from the SSD). EDIT2 Ok, so that doesn't work. The install detects the SSD, however, it cannot format it. EDIT3 After a fresh boot I can read out SMART-data and even perform a read-benchmark, but if I try to format it, or do a write-bench, it'll crap out and after that it says SMART is not supported. So basically it seems I can't write to the disk, as it will stop working when I do, I will try to run repeated read-benchmarks to see if that has any effect. EDIT4 I'm running several read benchmarks on the drive right now, they give results that are to be expected from an SSD. If the read-benches don't fail, I can use fdisk on the disk, but it is now stuck trying to re-read the partition table after issueing the 'w' command. EDIT5 Parted Magic did recognize the drive and with hdparm -I even could tell me the drive was in a frozen state. I powercycled it (just pull out the plug from the SSD and plug it back in) and it wasn't frozen anymore. After that I could upgrade the firmware on the drive (still using Parted Magic) and format it to Ext4. After I rebooted into the Ubuntu installer, it wouldn't get recognized and hdparm didn't want to talk to it saying HDIO_DRIVE_CMD(identify) failed: Invalid exchange. EDIT6 For some reason if I enable one of the RAID controllers (the one the SSD is connected to, obviously) Ubuntu will let me format it, mount it and write to it. The installer also recognizes it. However if the raid controller is enabled but no array is defined the motherboard can't boot from it :(

  Read the article

• Windows 7 Bluescreen: IRQ_NOT_LESS_OR_EQUAL | athrxusb.sys

  - by wretrOvian

  I'd left my system on last night, and found the bluescreen in the morning. This has been happening occasionally, over the past few days. Details: ================================================== Dump File : 022710-18236-01.dmp Crash Time : 2/27/2010 8:46:44 AM Bug Check String : DRIVER_IRQL_NOT_LESS_OR_EQUAL Bug Check Code : 0x000000d1 Parameter 1 : 00000000`00001001 Parameter 2 : 00000000`00000002 Parameter 3 : 00000000`00000000 Parameter 4 : fffff880`06b5c0e1 Caused By Driver : athrxusb.sys Caused By Address : athrxusb.sys+760e1 File Description : Product Name : Company : File Version : Processor : x64 Computer Name : Full Path : C:\Windows\minidump\022710-18236-01.dmp Processors Count : 2 Major Version : 15 Minor Version : 7600 ================================================== HiJackThis ("[...]" indicates removed text; full log [posted to pastebin][1]): Logfile of Trend Micro HijackThis v2.0.2 Scan saved at 8:49:15 AM, on 2/27/2010 Platform: Unknown Windows (WinNT 6.01.3504) MSInternet Explorer: Internet Explorer v8.00 (8.00.7600.16385) Boot mode: Normal Running processes: C:\Windows\DAODx.exe C:\Program Files (x86)\Asus\EPU\EPU.exe C:\Program Files\Asus\TurboV\TurboV.exe C:\Program Files (x86)\PowerISO\PWRISOVM.EXE C:\Program Files (x86)\OpenOffice.org 3\program\soffice.exe C:\Program Files (x86)\OpenOffice.org 3\program\soffice.bin D:\Downloads\HijackThis.exe C:\Program Files (x86)\uTorrent\uTorrent.exe R1 - HKCU\Software\Microsoft\Internet Explorer\[...] [...] O2 - BHO: Java(tm) Plug-In 2 SSV Helper - {DBC80044-A445-435b-BC74-9C25C1C588A9} - C:\Program Files (x86)\Java\jre6\bin\jp2ssv.dll O4 - HKLM\..\Run: [HDAudDeck] C:\Program Files (x86)\VIA\VIAudioi\VDeck\VDeck.exe -r O4 - HKLM\..\Run: [StartCCC] "C:\Program Files (x86)\ATI Technologies\ATI.ACE\Core-Static\CLIStart.exe" MSRun O4 - HKLM\..\Run: [TurboV] "C:\Program Files\Asus\TurboV\TurboV.exe" O4 - HKLM\..\Run: [PWRISOVM.EXE] C:\Program Files (x86)\PowerISO\PWRISOVM.EXE O4 - HKLM\..\Run: [googletalk] C:\Program Files (x86)\Google\Google Talk\googletalk.exe /autostart O4 - HKLM\..\Run: [AdobeCS4ServiceManager] "C:\Program Files (x86)\Common Files\Adobe\CS4ServiceManager\CS4ServiceManager.exe" -launchedbylogin O4 - HKCU\..\Run: [uTorrent] "C:\Program Files (x86)\uTorrent\uTorrent.exe" O4 - HKUS\S-1-5-19\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-19\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-20\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'NETWORK SERVICE') O4 - HKUS\S-1-5-20\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'NETWORK SERVICE') O4 - Startup: OpenOffice.org 3.1.lnk = C:\Program Files (x86)\OpenOffice.org 3\program\quickstart.exe O13 - Gopher Prefix: O23 - Service: @%SystemRoot%\system32\Alg.exe,-112 (ALG) - Unknown owner - C:\Windows\System32\alg.exe (file missing) O23 - Service: AMD External Events Utility - Unknown owner - C:\Windows\system32\atiesrxx.exe (file missing) O23 - Service: Asus System Control Service (AsSysCtrlService) - Unknown owner - C:\Program Files (x86)\Asus\AsSysCtrlService\1.00.02\AsSysCtrlService.exe O23 - Service: DeviceVM Meta Data Export Service (DvmMDES) - DeviceVM - C:\Asus.SYS\config\DVMExportService.exe O23 - Service: @%SystemRoot%\system32\efssvc.dll,-100 (EFS) - Unknown owner - C:\Windows\System32\lsass.exe (file missing) O23 - Service: ESET HTTP Server (EhttpSrv) - ESET - C:\Program Files\ESET\ESET NOD32 Antivirus\EHttpSrv.exe O23 - Service: ESET Service (ekrn) - ESET - C:\Program Files\ESET\ESET NOD32 Antivirus\x86\ekrn.exe O23 - Service: @%systemroot%\system32\fxsresm.dll,-118 (Fax) - Unknown owner - C:\Windows\system32\fxssvc.exe (file missing) O23 - Service: FLEXnet Licens

  Read the article

• Ubuntu Newbie Needs Assistance!!

  - by Steve Greene

  New Ubuntu User Needs Help!- version 9.10 does not communicate with laptop Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, even when sitting directly under the wireless router at the local library (literally), which puts out a wickedly-fast signal that my Windows Vista OS auto-detects and immediately connects to. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all, even though I am only a few feet from the router. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I desparately wish to convert to Ubuntu. I used Mac for ten years, and then Windows for ten years. Now, after 20 years, I want to live out my days as an open-source Ubuntu fanatic. I am ready to give the old status quo the boot! I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch so that I can move on in total Ubuntu bliss? My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System. I am running Windows Vista Home Basic, Service Pack 2. My current email is [email protected] if you have a workable solution that does not require programmer status to implement. Surely this must be a simple fix that I simply am overlooking, but being the new guy on the block, I have yet to be enlightened. Thanks for your help in coming up to speed!! Steve Wanna' be Ubuntu Fanatic "If you're not living on the edge, you're taking up too much space."

  Read the article

• Some apps very slow to load on Windows 7, copy & paste very slow.

  - by Mike

  Hello, I searched here and couldn't find a similar issue to mine but apologies if I missed it. I've searched the web and no one else seems to be having the same issue either. I'm running Windows 7 Ultimate 64bit on a pretty high spec. machine (well, apart from the graphics): Asus M4A79T Deluxe AMD Phenom II 965 black edition (quad core, 3.4GHz) 8GB Crucial Ballistix DDR 1333MHz RAM 80GB Intex X25 SSD for OS 500GB mechanical drive for data. ATi Radeon HD 4600 series PCI-e Be Quiet! 850W PSU I think those are all the relevant stats, if you need anything else let me know. I've updated chipset, graphics and various other drivers all to no avail, the problem remains. I have also unplugged and replugged every connection internally and cleaned the RAM edge connectors. The problems: Video LAN (VLC) and CDBurnerXP both take ages to load, I'm talking 30 seconds and 1 minute respectively which is really not right. Copy and paste from Open Office spread sheet into Fire Fox, for example, is really, really slow, I'll have pressed control V 5 or 6 times before it actually happens, if I copy and then wait 5 to 10 seconds or so it'll paste first time so it's definitely some sort of time lag. Command and Conquer - Generals: Zero Hour. When playing it'll run perfectly for about 10 or 20 seconds then it'll just pause for 3 or 4 then run for another 10 or 20 seconds and pause again and so on. I had the Task Manager open on my 2nd monitor whilst playing once and I noticed it was using about 25% of the CPU, pretty stable but when the pause came another task didn't shoot up to 100% like others on the web have been reporting (similar but not the same as my issue, often svchost.exe for them) but dropped to 2 or 3% usage then back up to 25% when it started playing properly again. Very odd! But it gets even odder... I had a BSOD and reboot last week, when it rebooted the problem had completely gone, I could play C&C to my heart's content and both the other apps loaded instantly, copy and paste worked instantly too. I did an AVG update earlier this week which required a reboot, rebooted and the problem's back. I don't think it's AVG related though, I think it was just coincidence that's the app that required a reboot. I think any reboot would have brought the issue back. A number of reboots later and it hasn't gone away again. If any one could make any suggestions as to the likely cause and solution to these issues I'd be most grateful, it's driving me nuts! Thanks, Mike....

  Read the article

• Crashes and freezes after fixing "BOOTMGR is missing" error

  - by Greg-J

  I came back from a 3-day weekend to a computer that was off. I leave my PC on 24/7, so this was odd. Turn it on to get the dreaded "BOOTMGR is missing" screen. Two attempts at Windows Recovery and it booted into Windows fine. After an hour or so, I get a frozen Chrome and my start bar disappears. Ctrl+Alt+Del brings up an error box telling me that Ctrl+Alt+Del failed to work properly. Clicking on any open application triggers an error (I can't recall the error now, but it essentially just said that the application couldn't be found running or something along those lines). I restart, and again, the same thing happens after a while of use. I turn it on, install the 47 updates I have or so, and then restart it. After a while of use (under an hour), it just freezes completely. My thoughts are: SSDs, RAM or PS. My system specs below: (RAID0) 2 x Crucial M4 CT128M4SSD2 2.5" 128GB SATA III MLC Internal Solid State Drive (SSD) CORSAIR Vengeance 16GB (4 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Desktop Memory Model CML16GX3M4A1600C9 CORSAIR HX Series HX750 750W ATX12V 2.3 / EPS12V 2.91 SLI Ready CrossFire Ready 80 PLUS GOLD Certified Modular Active 1 x ASUS Maximus IV Gene-Z/GEN3 LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard 1 x Hitachi GST Deskstar 7K1000.C 0F10383 1TB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive 1 x Intel Core i7-2600K Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 1 x SAPPHIRE 21197-00-40G Radeon HD 7970 3GB 384-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card 1 x Noctua NH-D14 120mm & 140mm SSO CPU Cooler This is all crammed in a pretty small case (NZXT Vulcan) and has been running perfectly problem-free since January. The only thing out of the ordinary is that there is a fan in the case that is now making noise whereas the case has previously been completely silent. I have no reason to believe this is anything more then correlation, but felt it is worth mentioning. I believe it MAY be the SSDs simply because of the BOOTMGR error, but not sure how to test that theory. My belief that it may be the RAM is simply from experience with frozen machines. I haven't had the time to memtest it, but will. The PS being the culprit is something I've picked up by reading similar threads on various forums, and it seems plausible. I am unsure how to test this though. ANY insight whatsover would be greatly appreciated!

  Read the article

• Windows Setup could not configure Windows to run on this computer's hardware

  - by Hello71

  The whole installation goes smoothly up to the point of "Completing installation ...". The monitor changes resolution, after which a standard dialog box pops up saying Windows Setup could not configure Windows to run on this computer's hardware Then, in a few seconds, the whole machine powers down. Trying to restart produces the message: STOP: c000021a {Fatal System Error} 0x00000000 (0xc0000001 0x00100448) OR it boots into Setup and comes up with the message: Windows Setup encountered an unexpected error... (This is not the actual error, just paraphrasing) I tried using the OEM restore instead of a regular install, but it fails with the same error. (Even though it worked before...) General specs: HP Pavilion Elite e9262f Intel Core i5-750 Processor ATI Radeon HD 4650 Hitachi HDT721010SLA360 ATA Device 6GB DDR3 RAM SuperMulti DVD Burner with LightScribe Some built-in Wi-Fi module http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01916917 I've tried disconnecting the wireless card and disabling the built-in Ethernet and Firewire via the BIOS, and replacing the wireless keyboard and mouse with wired USB ones. Didn't work. I've also tried changing the SATA controller settings in the BIOS to RAID, AHCI, and IDE, reinstalling each time I changed. Still not working. I think the reason why it is showing the Fatal System Error is because it didn't finish installing before it errored out and shut down, so the system is left in an inconsistent state. I've tried 3 different copies (including the OEM restore) of Windows 7 now, and they're all failing at the same point, with the same error message. I've tried to install Windows 7 maybe 10 times already, with the exact same error message at the exact same location. Hm... Interestingly, the 32-bit version of Windows 7 works, but the 64-bit version doesn't. Perhaps it was a badly burned disk? Reburning the 64-bit version still comes up with the same error. Here's a picture of the side of the case that clearly says it came with Windows 7 64-bit, along with the model number and CPU. sudo fdisk -l: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009896f Device Boot Start End Blocks Id System /dev/sda1 * 1 13 104391 7 HPFS/NTFS /dev/sda2 14 94119 755906445 7 HPFS/NTFS /dev/sda3 119922 121602 13492224 7 HPFS/NTFS /dev/sda4 94120 119922 207257740+ 5 Extended /dev/sda5 119527 119922 3170769 82 Linux swap / Solaris /dev/sda6 107174 119526 99225441 83 Linux /dev/sda7 94120 107173 104856192 7 HPFS/NTFS Partition table entries are not in disk order

  Read the article

• recommendations for efficient offsite remote backup solution of vm's

  - by senorsmile

  I am looking for recommendations for backing up my current 6 vm's(and soon to grow to up to 20). Currently I am running a two node proxmox cluster(which is a debian base using kvm for virtualization with a custom web front end to administer). I have two nearly identical boxes with amd phenom II x4's and asus motherboards. Each has 4 500 GB sata2 hdd's, 1 for the os and other data for the proxmox install, and 3 using mdadm+drbd+lvm to share the 1.5 TB's of storage between the two machines. I mount lvm images to kvm for all of the virtual machines. I currently have the ability to do live transfer from one machine to the other, typically within seconds(it takes about 2 minutes on the largest vm running win2008 with m$ sql server). I am using proxmox's built-in vzdump utility to take snapshots of the vm's and store those on an external harddrive on the network. I then have jungledisk service (using rackspace) to sync the vzdump folder for remote offsite backup. This is all fine and dandy, but it's not very scalable. For one, the backups themselves can take up to a few hours every night. With jungledisk's block level incremental transfers, the sync only transfers a small portion of the data offsite, but that still takes at least a half an hour. The much better solution would of course be something that allows me to instantly take the difference of two time points (say what was written from 6am to 7am), zip it, then send that difference file to the backup server which would instantly transfer to the remote storage on rackspace. I have looked a little into zfs and it's ability to do send/receive. That coupled with a pipe of the data in bzip or something would seem perfect. However, it seems that implementing a nexenta server with zfs would essentially require at least one or two more dedicated storage servers to serve iSCSI block volumes (via zvol's???) to the proxmox servers. I would prefer to keep the setup as minimal as possible (i.e. NOT having separate storage servers) if at all possible. I have also briefly read about zumastor. It looks like it could also do what I want, but it appears to have halted development in 2008. So, zfs, zumastor or other?

  Read the article

• NX Client for Windows 7 Opens Remote Desktop in Multiple Windows

  - by Corey Kennedy

  What I'm trying to do: access my Ubuntu desktop remotely via NX Client on my Windows 7 laptop. My environment: server: Ubuntu 10.10 on AMD 1Ghz/512MB RAM PC client: Windows 7 on ThinkPad sl510 Software: server is running NXServer 3.4.0. Using xfce4 window manager. Laptop is using NXClient for Windows In my NX Client "Desktop" settings I've selected "Unix" and "Custom" for OS and environment. I've also specified "startxfce4" as the application to launch when NX connects. I am able to authenticate an NX session on my laptop. By this I mean, I can start the client on my laptop, enter credentials for my Linux user, and NX establishes a connection to the server and attempts to open a remote desktop window. The problem, though, is that this remote desktop is "fragmented" into many Windows. One window will display the bulk of my desktop (complete with desktop icons for "Home," "File System," and "Trash") while another window will contain the taskbar, and another window will contain the application strip. I can select each of these Windows individually, but I cannot click on any objects within them. I've searched Super User, Ubuntu Forums, NX help, Server Fault, and tried many Google searches - none have turned up another case of this particular problem. I'm stumped. Does anyone have any suggestions for what I might try? I'm guessing the problem has to do with my xfce config files, but I've only just setup this server - it's been a long time since I've used Linux and there's a lot I just don't know. What I am NOT trying to do: use Desktop sharing from Ubuntu, whereby I VNC into a desktop that I've already established on the server. I am trying to configure this Linux box as a headless server that I can stash someplace out-of-the-way in my house, then interact with through my laptop. I don't want to have a monitor or keyboard connected to the Linux box. Thanks for your help! edit: 1/19/2011 Well, this is truly bizarre. To my knowledge I've made no changes to either system - the laptop or the server. But today after starting up the server for the first time in a few days, and making sure that nxserver was running, I was able to connect with the nxclient from my laptop with no problems. I have a full desktop in a single window and I am able to interact with it normally. This is really weird, but the problem seems to be resolved.

  Read the article

• How to force Debian to boot new Kernel?

  - by ThE_-_BliZZarD

  I'm running Debian 6, Debian GNU/Linux, with Linux 2.6.32-5-amd64 under Grub2 ( 1.98+20100804-14+squeeze1) on a remote system (no possibility to view the pre-boot messages). I compiled and installed a new kernel, but I can not get it to boot. What I have done: Installed the packages via: dpkg -i linux-headers-3.5.3.20120914-amd64_3.5.3.20120914-amd64-10.00.Custom_amd64.deb linux-image-3.5.3.20120914-amd64_3.5.3.20120914-amd64-10.00.Custom_amd64.deb This updated the Grub configuration. My /boot/grub/grub.cfg now contains: menuentry 'Debian GNU/Linux, with Linux 3.5.3.20120914-amd64' --class debian --class gnu-linux --class gnu --class os { insmod raid insmod mdraid insmod part_msdos insmod part_msdos insmod ext2 set root='(md0)' search --no-floppy --fs-uuid --set 5a3882a9-c7df-4f6a-9feb-f03e3e37be01 echo 'Loading Linux 3.5.3.20120914-amd64 ...' linux /vmlinuz-3.5.3.20120914-amd64 root=UUID=003242b5-121b-49f3-b32f-1b40aea56eed ro acpi=ht quiet panic=10 echo 'Loading initial ramdisk ...' initrd /initrd.img-3.5.3.20120914-amd64 } menuentry 'Debian GNU/Linux, with Linux 2.6.32-5-amd64' --class debian --class gnu-linux --class gnu --class os { insmod raid insmod mdraid insmod part_msdos insmod part_msdos insmod ext2 set root='(md0)' search --no-floppy --fs-uuid --set 5a3882a9-c7df-4f6a-9feb-f03e3e37be01 echo 'Loading Linux 2.6.32-5-amd64 ...' linux /vmlinuz-2.6.32-5-amd64 root=UUID=003242b5-121b-49f3-b32f-1b40aea56eed ro acpi=ht quiet panic=10 echo 'Loading initial ramdisk ...' initrd /initrd.img-2.6.32-5-amd64 } I used grub-set-default "Debian GNU/Linux, with Linux 2.6.32-5-amd64" to set the old kernel as default and then grub-reboot "Debian GNU/Linux, with Linux 3.5.3.20120914-amd64" to boot into the new kernel once. After update-grub I rebooted the system, but everytime it comes back up with the old kernel (2.6). I tried setting the new one as default (grub-set-default 0, update-grub, reboot) but, still the old one. The Syslogs contain NO hint whatsoever about trying to boot the new kernel - only the old one. Would there be any hints regarding problems with a kernel? Is there a way to enable debug-logging in grub? What am I doing wrong? How can I force the system to boot the new kernel? Edit: Hardware of remote machine. CPU cat /proc/cpuinfo processor : 0 vendor_id : AuthenticAMD cpu family : 16 model : 5 model name : AMD Athlon(tm) II X4 605e Processor stepping : 3 cpu MHz : 2294.898 cache size : 512 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 4 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm 3dnowext 3dnow constant_tsc rep_good nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt bogomips : 4589.77 TLB size : 1024 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm stc 100mhzsteps hwpstate (copied only the first, 3 more follow) The server is a Fujitsu PRIMERGY MX130 S1.

  Read the article

• Network use of Gaming PC

  - by Matthew Patrick Cashatt

  Background After YEARS of waiting, I built the custom gaming PC of my dreams: Intel i7 - 975 Extreme Edition 3.3ghz (overclocked to 4.0) ATI Radeon 5970 2gb Corsair 256 gb SSD Drive 2 TB Sata II 3.0 7200rpm data drive 12 GB Kingston Hyper-X (1600mhz) DDR3 Windows 7 Ultra 64 bit And so on. . . Problem I hooked this beast up to our home theater and settled in for a great gaming season only to realize a couple of drawbacks: It's hard to accurately wax bad guys using a keyboard in your lap whilst reclined on your couch (and using a wireless keyboard). It's hard to read the text on the screen (i.e. menus, etc). I find that a 1:1 ratio (screen diagonal inch to inch away from screen) is optimum, but using the home theater, it's more like 1:3 which has me squinting unless I sit on the coffee table. The wife always seems to want the TV the same time I do and, unfortunately "Real Housewives of Beverly Hills" and Battlefield BC don't mix. I am losing the battle in the home theater room, but the PC has to stay there (long story). So, this leaves me with the option of playing in my home office which is about 30 feet away from the home theater. I am a software developer so I have a pretty decent set up in my office--multiple 1080p monitors, HP Envy 17 which can run games like Crysis in 720p with out stammering too much. Also, I can game very comfortably at my desk in the office. Still, even though the set up in my office can run games well enough, I don't want to regress to that when I have worked YEARS for an awesome gaming PC that can run everything on ultra high settings. My Question What are my options for running my games on the beastly desktop in the Home Theater, but physically playing in my office about 30 feet away? A really long HDMI cable? LAN/RDC? Details that May Help We have an open crawlspace so running cable from HT room to office is no problem. I already have networked the house with a LAN Any help is GREATLY appreciated. Thanks, Matt

  Read the article

• Subversion/Hudson/Sonar/Artifactory - too much for my little server to handle! Help!

  - by Ricket

  I have a little dedicated server. It's at a cheap price and has a simple AMD 1800+ (1.5ghz), 256mb DDR RAM, ...need I continue? And I think I'm overloading it already. I have installed the following, and it's running CentOS 5.4: Webmin Apache MySQL Subversion as an Apache module Hudson (standalone) Sonar (standalone, runs with a standalone Jetty install) Artifactory (standalone) That's pretty much it. But I'm having problems; pages are loading quite slowly. Network speed of the server is excellent, but I think I'm just running out of CPU and/or memory. A side-effect of the pages loading slowly is that sometimes Hudson times out, not being able to start Maven or contact Sonar in a certain amount of time. I think the next step to speed things up might be to move to an application server and use the WAR version of Hudson, Sonar and Artifactory together on that server. I don't know that it will help, but it just seems to make sense, especially with Sonar running on its own Jetty install and the other two probably running their own mini application servers as well. Am I correct in thinking this? Is this the right course of action? Any other tips on how to make the server run faster? I can post more data if you'd like, just let me know what else would help you answer my question. Oh, also just to cure any suspicions, I don't have any sort of virus or spyware. I protect my SSH access with DenyHosts (which has blocked 300+ brute forcers in the past few months), and I have confirmed that the top four processes in terms of memory and CPU usage are Sonar, Artifactory, Hudson, and MySQL. Edit: I just thought of another thing that I'd like you to comment on as well: Apache currently has 8 spawned slave processes, taking 42MB of ram apiece. This is not my web server. Is everything else able to function if I shut down Apache? Can you point me towards a tutorial or something on migrating Subversion from Apache into something that might work along with the other three applications, maybe even make Subversion a WAR file or something?

  Read the article

• Is it safe to enable forced ASLR via EMET on Windows?

  - by D.W.

  I'd like to enable forced ASLR for all DLLs on Windows. Is this safe? Background: ASLR is an important security mechanism that helps defend against code injection attacks. DLLs can opt into ASLR, and most do, but some DLLs have not opted into ASLR. If a program loads even a single non-ASLRized DLL, then the program doesn't get the benefit/protection of ASLR. This is a problem, because there are a non-trivial number of DLLs that haven't opted into ASLR. For instance, it was recently revealed that Dropbox injects a DLL into a bunch of processes, and the Dropbox DLL doesn't have ASLR turned on, which negates any ASLR protection they otherwise would have had. Unfortunately, there are many other widely used DLLs that haven't opted into ASLR. This is bad for system security. Microsoft provides several ways to turn on ASLR for all DLLs, even ones that haven't opted into ASLR: On Windows 7 and Windows Server 2008, you can enable "Force ASLR" in the registry. On all Windows versions, you can use Microsoft's EMET tool and enable EMET's "Mandatory ASLR" option. These methods are possible because all DLLs are compiled as position-independent code and they can be relocated to a random location even if they haven't opted into ASLR. These options will ensure that ASLR is turned on, even if the developers of the DLL forgot to opt into ASLR. Thus, forcing on ASLR systemwide may help system security. In principle, turning on forced ASLR could potentially break a poorly-written DLL, so there is some risk of breakage. I'm interested in finding out just significant this risk is. I have the suspicion that this kind of breakage might be extremely rare. Here's what I've been able to find: Microsoft has done compatibility testing with several dozen widely used applications. The only one they found where Mandatory ASLR causes problems is Windows Media Player. All the other applications continue working fine. (See pp.39-41 of this document.) I've seen some anecdotal reports that enabling "Mandatory ASLR"/"Force ASLR" is fine and unlikely to cause problems. CERT reports that AMD and ATI video drivers used to crash if you enabled forced ASLR, but their latest drivers have now fixed this problem. They don't show any other drivers with this problem. A forum post from Microsoft shows no other applications with compatibility problems if ASLR is forced on, as of 2011. A user reports that borderlands.exe, a video game by Gearbox Software, crashes if you turn on mandatory ASLR. What else should I know? Is it relatively safe to turn on Force ASLR / Mandatory ASLR systemwide to harden the secuity of my system, or will I be in for a world of pain and broken applications? How significant is the risk of compatibility problems and broken applications?

  Read the article

< Previous Page | 65 66 67 68 69 70 71 72 73  | Next Page >