Search Results

Search found 1812 results on 73 pages for 'amd radeon'.

Page 67/73 | < Previous Page | 63 64 65 66 67 68 69 70 71 72 73  | Next Page >

• Computer will freeze/ lock up after doing relatively stressful things

  - by GrowingCode247

  I'll first start off by saying that the issue GENERALLY doesn't occur unless I'm doing something remotely stressful for my computer. This issue used to occur whenever it felt it was necessary, however has not occurred completely randomly for a while now (thankfully) My computer's specs: CPU: AMD Phenom II X4 960T GPU: GeForce GTX 760 Memory: 16 GB RAM Resolution Used: 1680x1050, 59Hz (strange number for refresh rate?) res is highest for monitor Nvidia Driver version: 331.65 OS: Microsoft Windows 7 Ultimate (64-bit) Sometimes I will be able to go 2-3 games (about an hour, depending) and sometimes it will go maybe one game (20-30 minutes) and then my computer will run sluggishly and leave me unable to do much of anything. I can sometimes interact with programs at a very basic level (maximizing, minimizing), and I usually cannot close them in any way, not even through Task Manager. The highest temperature my GPU reaches is 76C, with the average being around 73C. During the time the temperatures are around 73C, my GPU's RAM usage is anywhere between 1250-1300 (out of 2GB). My CPU's temperature never goes over 60C, thankfully. The PSU should be fine. It's very mildly dusty but I feel as though that would not be causing this problem... I will clean it out as soon as everything else has been ruled out. Honestly I have no clue how to test the PSU for problems - same goes for my Motherboard. I cannot really think of what could be causing these freezes otherwise. Event Viewer details: EventID: 1 - VDS Basic Provider (I've no clue what this is) EventID: 3 - Kernel-EventTracing (Again, lost) EventID: 8003 - bowser (this seems fishy) and the one critical that I know others have been dealing with as I've browsed some other responses on the web: EventID: 41 - Kernel-Power any help to solve this problem would be GREATLY appreciated.

  Read the article

• How to fix missing RAID1 drive

  - by Sodved

  I had to do some fiddling about with my cables inside thebox and now I am getting a "Critical Error" about the RAID disks during startup. I have a gigabyte GA-MA770T-UD3 motherboard. Aparently the RAID controller is an AMD SB710 chip. I'm pretty sure I know what happenned. The first time I rebooted I had forgotten the power cable on one of the disks in the RAID1 (mirror) and let it boot up. So I shut down and put the power back in. So now when it boots up I go into the RAID admin interface (between the BIOS screen and the OS loading): it shows the RAID1 as in error the logical device has one disk and says the other is disconnected or missing the other physical disk shows up as a single disk If I boot to the OS (Windows 7 32 bit) the data all seems to be there. If I go into computer management it says my partition is on a disk and working OK. But the other disk is offline because: "The disk is offline because it has a signature collision with another disk that is online" So I am guessing because I STUPIDLY booted up with only one of the disks powered on, the other disk fell out of synch with the mirror and so now cannot rejoin the mirror. How do I fix this? I want to get the RAID1 mirror working again. There does not appear to be any "Repair" option in the basic RAID admin tool which I get into during startup before the OS boots. I have not made any explicit changes to the online one (but I guess the OS has probably written some admin data).

  Read the article

• Inexpensive (used) hardware for Xen virtualization test?

  - by Jason Antman

  Virtualization is one of the areas where I could really use some experience. I also run quite a few services (web, mail, dns, etc.) out of my home. Since most of my hardware is getting a bit old (I'm running on stuff that was surplused years ago...) I decided that it's about time I start renewing some things, and also play around with virtualization a bit more. My plan is to setup a SAN box (simple iSCSI target, relatively inexpensive gigE switch), get a pair (for starters) of new servers, and start building some new stuff with Xen, specifically planning on playing with live migration and full virtualization. Does anyone have recommendations for used, older "servers" (really anything in a rack-mount form factor, I'm not too worried about things like iLO/iLOM for the test nodes) that support VT-x/AMD-V? I'm biased to HP, but it looks like they didn't make Proliants with VT-x/Vanderpool processors until G6 (for the DL360) or so, which is way out of my price range. I'm looking in the sub-$300 range (or less, if possible), used, probably Ebay. Any recommendations are greatly appreciated. Edit:And, to catch this before the comments start coming - these are personal systems. I have first-generation Proliants still in use (I got them as corporate surplus in 05, they've been running since then, and probably were running since 01 or 02 prior to being sold). I don't need anything shiny and new - I've got a bunch of old boxes, at least one complete replacement for every model in use, and that's fine for me (and easy on the wallet).

  Read the article

• Nvidia 9800GT randomly prevents computer from booting

  - by Blender

  My computer has been running Windows and Linux perfectly fine with my 9800GT for the past year or so, but today it refused to boot. When I press the power button, this is what happens: Power button flashes once. Fans whir. Graphics card makes clicking noise. Computer reboots. Go back to 1. The cycle just keeps going, and I have to yank the cord to make the computer stop. After about 30 attempts at booting it, the computer powers on and everything works. I'm pretty sure that the graphics card isn't malfunctioning, as I've been GPU computing on it for a while now without any hiccups. But the strange thing is, the computer boots perfectly fine in only 5 boots if I remove the card. The computer is a HP Pavilion a6028x Desktop PC: Processor: AMD Athlon 64 X2 (W) 4600+ 2.4 GHz (AM2 socket) Motherboard: ECS MCP61PM-HM (Nettle 1) RAM: 3GB DDR2 (two different brands) More specs here Does anybody know what could be the problem? Any help or information would be greatly appreciated!

  Read the article

• Linux can dual display but windows can't?

  - by Mr_CryptoPrime

  I have two monitors, one that is hdmi-to-dvi and the other vga-to-dvi. I have an AMD HD Radeon 6900 series graphics card installed. I got Ubuntu to display dual monitors, but then I restarted for an update and then Ubuntu wouldn't even boot in recovery mode, it just kept cycling forever...displaying something about "timeout: killing [filepath] [hexadecimal]. So I tried booting into windows (7-professional) and it crashed and displayed this after rebooting: IRQL_NOT_LESS_OR_EQUAL, PAGE_FAULT-IN-NONPAGED-AREA. I went into Bios and reverted to the system defaults and ran system restore and it booted ok, but the dvi-to-dvi monitor would not display. I made sure my drivers were updated and catalyst was updated. Also through research discovered only one is for vga and the other is digital only, so I put the vga-to-dvi in the vga slot and so on. Neither windows or catalyst will detect the dvi-to-dvi montior. Any suggestions? Thanks. EDIT: Found out that booting into Ubuntu with only one monitor (using either monitor with either cable) worked perfectly fine. I could then add another monitor and it displays ok. However, it will, out of the blue, suddenly distort the display. At first I thought the computer crashed, but it is something with the video output from the GPU to the monitor because I pushed the power button and it would refresh every 5secs or so and I could see the "Ubuntu will power down in X seconds", even though it was horribly distorted. Any ideas what's causing this?

  Read the article

• Ubuntu 12.04 VirtualBox on powerful W7 quite slow

  - by wnstnsmth

  I own a Thinkpad T420s with 8GB RAM, 160 GB SSD and a quite fast i7 processor. Summa summarum a very fast computer that works perfectly. Now, I am not very impressed by the performance of my Ubuntu 12.04 virtual machine running on VirtualBox 4.1.18. I assume that Virtual Machines are always a bit slower than the guest system, still I think it should be more performant given the hardware settings I give it: 4096 MB RAM 1 CPU without CPU limitation (I would like to give it more but then it does not seem to work - I am not experienced in this maybe somebody could give me advice on this too) Activated PAE/NX, VT-x/AMD-V and Nested Paging 96 MB Graphics Memory (no 2D or 3D acceleration) ~ 14 GB disk space, currently about 7 GB are used Maybe I misconfigured something, could you give me a hint please? Thanks! Edit: What I mean by slow is that for example switching tabs in the browser (whether FF or Chrome) only goes with a 0.5s delay or something, as well as switching application windows and/or double-clicking applications in the dock to get all open windows.. opening Aptana takes about a minute whereas opening something like Photoshop on the guest system takes 5 seconds

  Read the article

• how can a web page change my mouse speed?

  - by Tekaholic

  I usually have many tabs open in Firefox and I haven't been able to find one specific website that causes this because I don't seem to notice it right away. I'm going to click on something on my desktop and I am lifting up the mouse several times to get across the screen. It doesn't seem to matter what program I might be using because this happens on all desktops and in Firefox, too. So I go in my settings and I turn up the mouse speed all the way and it's still not really acceptable. It doesn't matter if I click on different tabs but when I close the browser, my mouse is way too sensitive, like I'd expect at the max setting. Then I go back to Control Center and return my mouse speed and acceleration to normal. When I restart my browser, the mouse remains normal. So is there something to this before I start wasting my time hunting through my history to discover which website or sites are having this effect? ...and if it is a specific site and I locate it, what can I change to stop it's effect on my mouse besides not visiting it? I am using Linux Mint 13 on a box with an AMD Athlon processor and 2gigs of ram. I never installed another browser because everything works for me.

  Read the article

• Some Portions of Computer Running Slow (Specifically Graphics)

  - by Mike Gates

  I noticed that a few things are running slow today on my Windows 7 laptop. Specifically, they are: Opening and closing windows takes several seconds for the animation to complete. Windows media player opens fine, but the movies are very laggy MMORPG's, such as RuneScape, are extremely laggy When waking my computer from sleep mode, after entering my password, my desktop takes about 3 seconds to fade in Other than those, everything runs at a normal speed. Things I've done that maybe contributed to this problem: Changed the graphics processor (by plugging in/unplugging the charger) [however, no matter how I change the graphics, I'm still getting this lagginess] Installed AdBlock, a Firefox addon [I recently removed it, and I'm still experiencing this problem] Went into Advanced System Settings, Clicked Settings, and unchecked a few visual things (such as the animation for opening and closing windows) [sure, this got rid of the opening/closing windows lag, but I like that little animation - plus that leaves all the other lag problems I'm experiencing] So, does anyone have any ideas/fixes? If so, please respond. Thank you. Some Other Information: I'm on a HP Pavillion dv7 laptop, 4285 Entertainment PC, with: intel CORE i5 inside, ATI Mobility Radeon Premium Graphics, Microsoft DirectX11 Opening and closing of windows: Defined as opening a program (i.e. Firefox) or closing it by hitting the X in the upper-right hand corner. Lately, the animation for opening and closing windows (which is simply either growing from the icon from the taskbar to fill the screen, or shrinking from the screen down towards the icon on the toolbar.) This problem also occurs for minimizing/maximizing windows. Very laggy movies: defined as .avi movie files saved to My Documents which skips several frames per second and seemingly slows down the movie as a whole Extremely laggy games: I tried RuneScape today, and movement in the game was at least 10x slower than it ever has been, even when playing on the lowest detail/graphics Desktop taking 3 seconds to fade in after sleep: in this scenario, I had no other programs running visibly. The computer generally fades to black from the password screen to the desktop in about 1 second, normally. However, it is now taking 3 or more seconds.

  Read the article

• vmware server 64 bit on ubuntu 9.10 64 bit with P2V windows 2003 SBS poor network speed

  - by RobertHC

  configuration is ubuntu 2.6.31-21 64 bit vmware 2.0.2 64 bit last release hardware is core 2 quad with 8GB ram guest is win 2003 server SBS 32 bit Dear friends, we have a converted physical to virtual windows sbs 2003, converted with last converter available nowadays http://www.vmware.com/products/converter/ vCenter converter. Running the P2V 2K3 SBS on vmware server, it does boot fine, but we do note an abnormal CPU activity and a poor lan speed. As attempts we did what follow. We removed all unneeded peripherals, we removed one NIC (phisycal server was 2 nics), we changed the vmx to ged the nic recognized as intel instead than amd, we removed 1 cpu (physical was 2 cpu), we removed anything was reported as failed driver from system events monitor. Nothing to do, no way and funny results. Let's read some tests results. All are made with the same file copied in different source folders. Copying from client side (both directions copy, to/from server) results are i.e. 10 seconds, copying the same files from server side (again from and to server) results are different... from client to server, speed is round about (bit more) 10 seconds, but from server to client direction is slower: double the time. Beeing very fast and launching a simultaneous copy "from server to client"+"from client to server", this made from the server side, results in a stuck traffic... 45 seconds to do the copy. vmware tools are installed and e1000 driver has been updated. With one processor CPU activity is still going up and down but much less than with two. Because of test, we installed win 2k8 STD 64 bit. We repeated all the above tests with exactly the same file result is just one: always 5 seconds (this matches the lan speed) Any idea about this issue is welcome and thank you if any. Kind regards R.

  Read the article

• How many iptables block rules is too many

  - by mhost

  We have a server with a Quad-Core AMD Opteron Processor 2378. It acts as our firewall for several servers. I've been asked to block all IPs from China. In a separate network, we have some small VPS machines (256MB and 512MB). I've been asked to block china on those VPS's as well. I've looked online and found lists which requires 4500 block rules. My question is will putting in all 4500 rules be a problem? I know iptables can handle far more rules than that, what I am concerned about is since these are blocks that I don't want to have access to any port, I need to put these rules before any allow. This means all legitimate traffic needs to be compared to all those rules before getting through. Will the traffic be noticeably slower after implementing this? Will those small VPS's be able to handle processing that many rules for every new packet (I'll put an established allow before the blocks)? My question is not How many rules can iptables support?, its about the effect that these rules will have on load and speed. Thanks.

  Read the article

• computer randomly restarting. both in game and out of game

  - by eric

  first my specs are. AMD Phenom II x4 955 processor 3.2ghz 20gb ddr3 ram 4Gb Nvidia Geforce GTX 770 850w Corsair tx850w psu Gigabyte ud3 mobo Windows 7 professional I recently uprgraded my vid card to gtx770 and upgraded my psu to the 850w thats in it now. i did a reformat with the installation of the new gpu and psu and started fresh and only have a couple programs installed (diablo3, nvidia control panel, wow, and steam). all drivers are up to date and everything is hooked up correctly. the problem is it will randomly shut down. no blue screen. just turns itself straight off and reboots after a couple seconds. occasionally i will have to unplug the power cable from the psu for a few minutes then reconnect and it will start up. it seems pretty random. sometimes it does it when my pc is just sitting there on the home screen. and sometimes it does it during games. and sometimes it doesnt do it for days at a time. i noticed the psu felt hot so i put an extra fan blowing straight onto both the psu and gpu and neither feel overly hot after it shuts down now. could it just be that it is a psu problem. the psu was taken from another machine but wasnt having this problem in that machine. i have seen a few articles online about gtx770 doing the same thing. but i havent found any answers or solutions. any help will be appreciated. im sure the 850w is enough to power my machine, im just stumped and ran out of ideas to fix it. i have even returned the video card for another thinking it might have been an issue with that particular card, but still gettin the same problem.

  Read the article

• What could possibly cause my computer to power down at random times?

  - by geoffreydv

  I have recently bought a new Power Supply and a new graphics card. My PC ran smoothly for a few months now but since a couple of days I'm having a strange problem. I am trying to isolate the problem to a specific piece of hardware (because if it's either the Power Supply or the Graphics card they are still under warranty). The problem started when I was playing a game (diablo 3). My PC suddenly powered down. I was unable to turn it on again by pressing the power button. I unplugged the power cable for a few seconds and plugged it back in. This time the pc powered on but the indication light turned orange instead of white as it normally does. The fans were not spinning and I did not see anything on my screen. After trying a couple of times I gave up. Two days later I tried again and this time the PC did boot up as usual. Everything looked okay until I tested if the problem was resolved by starting Diablo again. After about two minutes it powered down again as it did the first time. If I don't run any games my PC does power down after about 3-5 hours. Another fact that might be relevant: One time the PC did not shut down immediatly, instead first my graphics "powered down" but the music I was playing kept on playing. After about 20 seconds the pc powered down completely as usual. What I also noticed is that when I boot instantly after a power down, the chance of another power down occuring is much higher. Does anyone have an idea what could be causing this kind of behaviour or has a certain tool to diagnose the specific hardware parts? Thanks Specs: Memory: 6GB Processor: Intel i5 OS: Windows 7 64 bit The PC is a Dell Studio XPS 8100 with a replaced PSU and Graphics card: PSU: Corsair CX500 (500 watt) Graphics card: AMD Radeon 6850

  Read the article

• Y560 Lenovo IdeaPad bandwidth issue

  - by Vlakarados

  I have a Y560 Lenovo IdeaPad, my config: i7 740QM, 4GB RAM, RADEON HD 6570m/5700 1024MB and my network adapter is Intel WIFI Link 5150. The laptop is 2 years old and the problem I'm about to describe is present from the first day. As may be seen here, the receive bandwidth should be up to 300 Mbps, but the maximum download speed from LAN and using torrents is about 2.4MB/s. My internet connection is 100Mbps and other laptops in my house have the appropriate download speed - up to 12MB/s, I have tested at my friends house and at my job, the speed remains the same. I have tried all possible configurations I could think of in network settings - nothing helps. I use Windows 7 and I have had installed different versions (Ultimate, Professional, Home, OEM Home, 64 and 32 bit versions). Some time ago I searched for the problem and found one or two threads that had the same problem and there were something said about a limitation in firmware that some experienced users have managed to bypass. Updating drivers didn't help me either. Is there any reliable way to fix this?

  Read the article

• Fixing bent pins on a CPU

  - by Pekka

  While replacing a mainboard in a desktop machine (see related question), I did something stupid. I inserted the CPU into the new mainboard, but didn't check for the right position. When it didn't immediately lock in, I pressed slightly before realizing what was wrong. The result was a number of bent pins. I tried every tutorial that popped up when Googling "CPU bent pins" - using credit cards, sewing needles, and a hunting knife to get the pins back into position - but to no avail: For every pin I get straightened out, two others are bent. I have no problem getting individual pins straightened out, but my many attempts have led to many pins being slightly askew - enough for the CPU not to fit into the socket (An AMD X3 one). Maybe I just lack the motoric finesse. What I would need is some sort of a grid to fix all pins at once. It's a €50 processor so the loss is not catastrophic. But I thought before I go buy a new one, I thought I'd check here whether anybody knows some magic trick, or a cheap generally-available tool to fix this.

  Read the article

• Duplicate monitor on highest resolution in Windows 7

  - by AlexanderMP

  I have a monitor with a native resolution of 2560x1440, connected through display port. I also have an AV Receiver connected to the video card via HDMI, to have surround sound in games. All using Radeon HD 5670 (will upgrade soon to HD 7850). The problem is that my computer detects the receiver as a separate monitor, with the highest available resolution of 1920x1080. I have 3 options: Disconnect the second display. But then the sound (digital audio output through video card) also disappears. Duplicate displays. But then my primary monitor resolution is reduced to a maximum of just 1920x1080, that being the maximum of the second monitor. Extend desktop. This is the solution I picked so far, it being the least evil. The problems I face in this situations are 2: I have a blank part of the desktop where I sometimes lose my mouse pointer, so I made the extension small, 640x480, and placed it in a corner; when I turn off the main display, all windows resize to 640x480. In Kubuntu I had the option to duplicate the displays, while keeping the higher resolution. Which was great. I tried overriding using the Win7 netbook hack, but it's not available on non-netbooks. Is there a similar solution for this problem in Windows 7?

  Read the article

• Does VLC Player work well on Windows 7 64-bit?

  - by ????

  I tried VLC Player on Windows 7 64-bit version and the playback was fine, but when the video is maximized the image is very pixelated. I tried this on a Radeon HD 2600 XT graphics card as well as a computer with an Intel graphics chipset and both have the same result. If I use VLC Player on Windows 7 32-bit instead of 64-bit, there is no pixelation. Is this a known problem or is there any method to fix it on Windows 7 64-bit? Update: there isn't a 32-bit vs 64-bit version of VLC player, is there? (unlike 7-Zip) I also tried GOM Player and it doesn't have the problem on Windows 7 64-bit. Update: Nov 4, 2009 VLC displays an update notice: VLC 1.0.3 is a minor release fixing many bugs, especially for Windows Vista and 7, but it also introduces 2 new modes for deinterlacing, and a new udev module. Major fixes are about WMA Pro support, Dolby tracks in 4.0, v4l/v4l2 and atsc and a crash in mjpeg demuxer. Update of translations are also part of this release.

  Read the article

• Which Windows 8 tool should I use to "read", "upload", my Windows 7 latest backup DVD (is it possible?)

  - by Robert

  Which Windows 8 tool should I use to "read", "upload", my Windows 7 latest backup DVD (is it possible?). I've just installed W8 and haven't made any changes to my new ecosystem and, what happened was that, as I was managing my new drivers, some mess* occurred, I confess, and now what I have left is every single backup tool I made use of W7, like system images, restore dvds, backup up to date monthly and so on, and would like to keep in touch with W8. I'm one of those with problems managing the amd switchable gpu drivers. Now I want to stay with W8 (download version - didn't clean install) but with my old personal files. I don't care to programs updates. I got everything original on dvds, of my interest. Yesterday I tried refreshing W8 once but didn't work. Maybe trying again tonight. What would you guys do in my place, please? *the mess I am talking about is to have disabled my intel (the only driver left) gpu in device manager tool in W8. I got black screen on system boot. Cheers, C.C.

  Read the article

• unexplainable packet drops with 5 ethernet NICs and low traffic on Ubuntu

  - by jon

  I'm stuck on problem where my machine started to drops packets with no sign of ANY system load or high interrupt usage after an upgrade to Ubuntu 12.04. My server is a network monitoring sensor, running Ubuntu LTS 12.04, it passively collects packets from 5 interfaces doing network intrusion type stuff. Before the upgrade I managed to collect 200+GB of packets a day while writing them to disk with around 0% packet loss depending on the day with the help of CPU affinity and NIC IRQ to CPU bindings. Now I lose a great deal of packets with none of my applications running and at very low PPS rate which a modern workstation NIC would have no trouble with. Specs: x64 Xeon 4 cores 3.2 Ghz 16 GB RAM NICs: 5 Intel Pro NICs using the e1000 driver (NAPI). [1] eth0 and eth1 are integrated NICs (in the motherboard) There are 2 other PCI-X network cards, each with 2 Ethernet ports. 3 of the interfaces are running at Gigabit Ethernet, the others are not because they're attached to hubs. Specs: [2] http://support.dell.com/support/edocs/systems/pe2850/en/ug/t1390aa.htm uptime 17:36:00 up 1:43, 2 users, load average: 0.00, 0.01, 0.05 # uname -a Linux nms 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux I also have the CPU governor set to performance mode and irqbalance off. The problem still occurs with them on. # lspci -t -vv -[0000:00]-+-00.0 Intel Corporation E7520 Memory Controller Hub +-02.0-[01-03]--+-00.0-[02]----0e.0 Dell PowerEdge Expandable RAID controller 4 | \-00.2-[03]-- +-04.0-[04]-- +-05.0-[05-07]--+-00.0-[06]----07.0 Intel Corporation 82541GI Gigabit Ethernet Controller | \-00.2-[07]----08.0 Intel Corporation 82541GI Gigabit Ethernet Controller +-06.0-[08-0a]--+-00.0-[09]--+-04.0 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | | \-04.1 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | \-00.2-[0a]--+-02.0 Digium, Inc. Wildcard TE210P/TE212P dual-span T1/E1/J1 card 3.3V | +-03.0 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | \-03.1 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) +-1d.0 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 +-1d.1 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 +-1d.2 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 +-1d.7 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller +-1e.0-[0b]----0d.0 Advanced Micro Devices [AMD] nee ATI RV100 QY [Radeon 7000/VE] +-1f.0 Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge \-1f.1 Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller I believe the NIC nor the NIC drivers are dropping the packets because ethtool reports 0 under rx_missed_errors and rx_no_buffer_count for each interface. On the old system, if it couldn't keep up this is where the drops would be. I drop packets on multiple interfaces just about every second, usually in small increments of 2-4. I tried all these sysctl values, I'm currently using the uncommented ones. # cat /etc/sysctl.conf # high net.core.netdev_max_backlog = 3000000 net.core.rmem_max = 16000000 net.core.rmem_default = 8000000 # defaults #net.core.netdev_max_backlog = 1000 #net.core.rmem_max = 131071 #net.core.rmem_default = 163480 # moderate #net.core.netdev_max_backlog = 10000 #net.core.rmem_max = 33554432 #net.core.rmem_default = 33554432 Here's an example of an interface stats report with ethtool. They are all the same, nothing is out of the ordinary ( I think ), so I'm only going to show one: ethtool -S eth2 NIC statistics: rx_packets: 7498 tx_packets: 0 rx_bytes: 2722585 tx_bytes: 0 rx_broadcast: 327 tx_broadcast: 0 rx_multicast: 1504 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 1504 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 0 tx_tcp_seg_failed: 0 rx_flow_control_xon: 0 rx_flow_control_xoff: 0 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 2722585 rx_csum_offload_good: 0 rx_csum_offload_errors: 0 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 01 # ifconfig eth0 Link encap:Ethernet HWaddr 00:11:43:e0:e2:8c UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:373348 errors:16 dropped:95 overruns:0 frame:16 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:356830572 (356.8 MB) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:11:43:e0:e2:8d UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:13616 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8690528 (8.6 MB) TX bytes:0 (0.0 B) eth2 Link encap:Ethernet HWaddr 00:04:23:e1:77:6a UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:7750 errors:0 dropped:471 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2780935 (2.7 MB) TX bytes:0 (0.0 B) eth3 Link encap:Ethernet HWaddr 00:04:23:e1:77:6b UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:5112 errors:0 dropped:206 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:639472 (639.4 KB) TX bytes:0 (0.0 B) eth4 Link encap:Ethernet HWaddr 00:04:23:b6:35:6c UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:961467 errors:0 dropped:935 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:958561305 (958.5 MB) TX bytes:0 (0.0 B) eth5 Link encap:Ethernet HWaddr 00:04:23:b6:35:6d inet addr:192.168.1.6 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4264 errors:0 dropped:16 overruns:0 frame:0 TX packets:699 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:572228 (572.2 KB) TX bytes:124456 (124.4 KB) I tried the defaults, then started to play around with settings. I wasn't using any flow control and I increased the RxDescriptor count to 4096 before the upgrade as well without any problems. # cat /etc/modprobe.d/e1000.conf options e1000 XsumRX=0,0,0,0,0 RxDescriptors=4096,4096,4096,4096,4096 FlowControl=0,0,0,0,0 debug=16 Here's my network configuration file, I turned off checksumming and various offloading mechanisms along with setting CPU affinity with heavy use interfaces getting an entire CPU and light use interfaces sharing a CPU. I used these settings prior to the upgrade without problems. # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet manual pre-up /sbin/ethtool -G eth0 rx 4096 tx 0 pre-up /sbin/ethtool -K eth0 gro off gso off rx off pre-up /sbin/ethtool -A eth0 rx off autoneg off up ifconfig eth0 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/48/smp_affinity down ifconfig eth0 down post-down /sbin/ethtool -G eth0 rx 256 tx 256 post-down /sbin/ethtool -K eth0 gro on gso on rx on post-down /sbin/ethtool -A eth0 rx on autoneg on auto eth1 iface eth1 inet manual pre-up /sbin/ethtool -G eth1 rx 4096 tx 0 pre-up /sbin/ethtool -K eth1 gro off gso off rx off pre-up /sbin/ethtool -A eth1 rx off autoneg off up ifconfig eth1 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/49/smp_affinity down ifconfig eth1 down post-down /sbin/ethtool -G eth1 rx 256 tx 256 post-down /sbin/ethtool -K eth1 gro on gso on rx on post-down /sbin/ethtool -A eth1 rx on autoneg on auto eth2 iface eth2 inet manual pre-up /sbin/ethtool -G eth2 rx 4096 tx 0 pre-up /sbin/ethtool -K eth2 gro off gso off rx off pre-up /sbin/ethtool -A eth2 rx off autoneg off up ifconfig eth2 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "1" > /proc/irq/82/smp_affinity down ifconfig eth2 down post-down /sbin/ethtool -G eth2 rx 256 tx 256 post-down /sbin/ethtool -K eth2 gro on gso on rx on post-down /sbin/ethtool -A eth2 rx on autoneg on auto eth3 iface eth3 inet manual pre-up /sbin/ethtool -G eth3 rx 4096 tx 0 pre-up /sbin/ethtool -K eth3 gro off gso off rx off pre-up /sbin/ethtool -A eth3 rx off autoneg off up ifconfig eth3 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "2" > /proc/irq/83/smp_affinity down ifconfig eth3 down post-down /sbin/ethtool -G eth3 rx 256 tx 256 post-down /sbin/ethtool -K eth3 gro on gso on rx on post-down /sbin/ethtool -A eth3 rx on autoneg on auto eth4 iface eth4 inet manual pre-up /sbin/ethtool -G eth4 rx 4096 tx 0 pre-up /sbin/ethtool -K eth4 gro off gso off rx off pre-up /sbin/ethtool -A eth4 rx off autoneg off up ifconfig eth4 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/77/smp_affinity down ifconfig eth4 down post-down /sbin/ethtool -G eth4 rx 256 tx 256 post-down /sbin/ethtool -K eth4 gro on gso on rx on post-down /sbin/ethtool -A eth4 rx on autoneg on auto eth5 iface eth5 inet static pre-up /etc/fw.conf address 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.1 dns-nameservers 192.168.1.2 192.168.1.3 up ifconfig eth5 up post-up echo "8" > /proc/irq/77/smp_affinity down ifconfig eth5 down Here's a few examples of packet drops, i ran one after another, probabling totaling 3 or 4 seconds. You can see increases in the drops from the 1st and 3rd. This was a non-busy time, very little traffic. # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 225 lo: 0 eth2: 505 eth1: 0 eth5: 17 eth0: 105 eth4: 1034 # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 225 lo: 0 eth2: 507 eth1: 0 eth5: 17 eth0: 105 eth4: 1034 # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 227 lo: 0 eth2: 512 eth1: 0 eth5: 17 eth0: 105 eth4: 1039 I tried the pci=noacpi options. With and without, it's the same. This is what my interrupt stats looked like before the upgrade, after, with ACPI on PCI it showed multiple NICs bound to an interrupt and shared with other devices such as USB drives which I didn't like so I think i'm going to keep it with ACPI off as it's easier to designate sole purpose interrupts. Is there any advantage I would have using the default i.e. ACPI w/ PCI. ? # cat /etc/default/grub | grep CMD_LINE GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1 noacpi pci=noacpi" GRUB_CMDLINE_LINUX="" # cat /proc/interrupts CPU0 CPU1 CPU2 CPU3 0: 45 0 0 16 IO-APIC-edge timer 1: 1 0 0 7936 IO-APIC-edge i8042 2: 0 0 0 0 XT-PIC-XT-PIC cascade 6: 0 0 0 3 IO-APIC-edge floppy 8: 0 0 0 1 IO-APIC-edge rtc0 9: 0 0 0 0 IO-APIC-edge acpi 12: 0 0 0 1809 IO-APIC-edge i8042 14: 1 0 0 4498 IO-APIC-edge ata_piix 15: 0 0 0 0 IO-APIC-edge ata_piix 16: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb2 18: 0 0 0 1350 IO-APIC-fasteoi uhci_hcd:usb4, radeon 19: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb3 23: 0 0 0 4099 IO-APIC-fasteoi ehci_hcd:usb1 38: 0 0 0 61963 IO-APIC-fasteoi megaraid 48: 0 0 1002319 4 IO-APIC-fasteoi eth0 49: 0 0 38772 3 IO-APIC-fasteoi eth1 77: 0 0 130076 432159 IO-APIC-fasteoi eth4 78: 0 0 0 23917 IO-APIC-fasteoi eth5 82: 1329033 0 0 4 IO-APIC-fasteoi eth2 83: 0 4886525 0 6 IO-APIC-fasteoi eth3 NMI: 5 6 4 5 Non-maskable interrupts LOC: 61409 57076 64257 114764 Local timer interrupts SPU: 0 0 0 0 Spurious interrupts IWI: 0 0 0 0 IRQ work interrupts RES: 17956 25333 13436 14789 Rescheduling interrupts CAL: 22436 607 539 478 Function call interrupts TLB: 1525 1458 4600 4151 TLB shootdowns TRM: 0 0 0 0 Thermal event interrupts THR: 0 0 0 0 Threshold APIC interrupts MCE: 0 0 0 0 Machine check exceptions MCP: 16 16 16 16 Machine check polls ERR: 0 MIS: 0 Here's sample output of vmstat, showing the system. Barebones system right now. root@nms:~# vmstat -S m 1 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 14992 192 1029 0 0 56 2 419 29 1 0 99 0 0 0 0 14992 192 1029 0 0 0 0 922 27 0 0 100 0 0 0 0 14991 192 1029 0 0 0 36 763 50 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 646 35 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 722 54 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 793 27 0 0 100 0 ^C Here's dmesg output. I can't figure out why my PCI-X slots are negotiated as PCI. The network cards are all PCI-X with the exception of the integrated NICs that came with the server. In the output below it looks as if eth3 and eth2 negotiated at PCI-X speeds rather than PCI:66Mhz. Wouldn't they all drop to PCI:66Mhz? If your integrated NICs are PCI, as labeled below (eth0,eth1), then wouldn't all devices on your bus speed drop down to that slower bus speed? If not, I still don't know why only one of my NICs ( each has two ethernet ports) is labeled as PCI-X in the output below. Does that mean it is running at PCI-X speeds are is it showing that it's capable? # dmesg | grep e1000 [ 3678.349337] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 3678.349342] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 3678.349394] e1000 0000:06:07.0: PCI->APIC IRQ transform: INT A -> IRQ 48 [ 3678.409725] e1000 0000:06:07.0: Receive Descriptors set to 4096 [ 3678.409730] e1000 0000:06:07.0: Checksum Offload Disabled [ 3678.409734] e1000 0000:06:07.0: Flow Control Disabled [ 3678.586409] e1000 0000:06:07.0: eth0: (PCI:66MHz:32-bit) 00:11:43:e0:e2:8c [ 3678.586419] e1000 0000:06:07.0: eth0: Intel(R) PRO/1000 Network Connection [ 3678.586642] e1000 0000:07:08.0: PCI->APIC IRQ transform: INT A -> IRQ 49 [ 3678.649854] e1000 0000:07:08.0: Receive Descriptors set to 4096 [ 3678.649859] e1000 0000:07:08.0: Checksum Offload Disabled [ 3678.649863] e1000 0000:07:08.0: Flow Control Disabled [ 3678.826436] e1000 0000:07:08.0: eth1: (PCI:66MHz:32-bit) 00:11:43:e0:e2:8d [ 3678.826444] e1000 0000:07:08.0: eth1: Intel(R) PRO/1000 Network Connection [ 3678.826627] e1000 0000:09:04.0: PCI->APIC IRQ transform: INT A -> IRQ 82 [ 3679.093266] e1000 0000:09:04.0: Receive Descriptors set to 4096 [ 3679.093271] e1000 0000:09:04.0: Checksum Offload Disabled [ 3679.093275] e1000 0000:09:04.0: Flow Control Disabled [ 3679.130239] e1000 0000:09:04.0: eth2: (PCI-X:133MHz:64-bit) 00:04:23:e1:77:6a [ 3679.130246] e1000 0000:09:04.0: eth2: Intel(R) PRO/1000 Network Connection [ 3679.130449] e1000 0000:09:04.1: PCI->APIC IRQ transform: INT B -> IRQ 83 [ 3679.397312] e1000 0000:09:04.1: Receive Descriptors set to 4096 [ 3679.397318] e1000 0000:09:04.1: Checksum Offload Disabled [ 3679.397321] e1000 0000:09:04.1: Flow Control Disabled [ 3679.434350] e1000 0000:09:04.1: eth3: (PCI-X:133MHz:64-bit) 00:04:23:e1:77:6b [ 3679.434360] e1000 0000:09:04.1: eth3: Intel(R) PRO/1000 Network Connection [ 3679.434553] e1000 0000:0a:03.0: PCI->APIC IRQ transform: INT A -> IRQ 77 [ 3679.704072] e1000 0000:0a:03.0: Receive Descriptors set to 4096 [ 3679.704077] e1000 0000:0a:03.0: Checksum Offload Disabled [ 3679.704081] e1000 0000:0a:03.0: Flow Control Disabled [ 3679.738364] e1000 0000:0a:03.0: eth4: (PCI:33MHz:64-bit) 00:04:23:b6:35:6c [ 3679.738371] e1000 0000:0a:03.0: eth4: Intel(R) PRO/1000 Network Connection [ 3679.738538] e1000 0000:0a:03.1: PCI->APIC IRQ transform: INT B -> IRQ 78 [ 3680.046060] e1000 0000:0a:03.1: eth5: (PCI:33MHz:64-bit) 00:04:23:b6:35:6d [ 3680.046067] e1000 0000:0a:03.1: eth5: Intel(R) PRO/1000 Network Connection [ 3682.132415] e1000: eth0 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.224423] e1000: eth1 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.316385] e1000: eth2 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.408391] e1000: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 3682.500396] e1000: eth4 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 3682.708401] e1000: eth5 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX At first I thought it was the NIC drivers but I'm not so sure. I really have no idea where else to look at the moment. Any help is greatly appreciated as I'm struggling with this. If you need more information just ask. Thanks! [1]http://www.cs.fsu.edu/~baker/devices/lxr/http/source/linux/Documentation/networking/e1000.txt?v=2.6.11.8 [2] http://support.dell.com/support/edocs/systems/pe2850/en/ug/t1390aa.htm

  Read the article

• Failling install Ralink RT5592 driver on Ubuntu 14.04 LTS

  - by atisou

  My problem concerns the installation of a wi-fi driver (RT5592) for my new wi-fi adapter (PCE-N53) on my newly built computer. Basically, I don't manage to get the driver installed and therefore I cannot get the wifi to work. I know I am not the only one having this issue this year, between RT5592 driver and Ubuntu 14.04 LTS, in one way or the other. Is there anybody who has ever been able to fix this problem? It does not look like on all the posts I have been through... Following an answer to a same problem as mine (I was getting the same error message as Christopher Kyle Horton of "incompatible types" etc), I have applied the instructions and done the editings in a script as suggested by Paul B. Unfortunately I still do get error/warnings message (a different one this time) at the end of the make and the wi-fi still does not work. Below is a snapshot of the end of the message: In file included from /home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/include/os/rt_linux.h:31:0, from /home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/include/rtmp_os.h:44, from /home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/include/rtmp_comm.h:69, from /home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/pci_main_dev.c:31: include/linux/module.h:88:32: error: ‘__mod_pci_device_table’ aliased to undefined symbol ‘rt2860_pci_tbl’ extern const struct gtype##_id __mod_##gtype##_table \ ^ include/linux/module.h:146:3: note: in expansion of macro ‘MODULE_GENERIC_TABLE’ MODULE_GENERIC_TABLE(type##_device,name) ^ /home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/pci_main_dev.c:73:1: note: in expansion of macro ‘MODULE_DEVICE_TABLE’ MODULE_DEVICE_TABLE(pci, rt2860_pci_tbl); ^ cc1: some warnings being treated as errors make[2]: *** [/home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux/../../os/linux/pci_main_dev.o] Error 1 make[1]: *** [_module_/home/username/Downloads/PCE-N53/Linux/DPO_GPL_RT5592STA_LinuxSTA_v2.6.0.0_20120326/os/linux] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.13.0-32-generic' make: *** [LINUX] Error 2 The full pastebin data: paste.ubuntu.com/8088834/ It looks from the message that one would need to edit manually some of/other scripts in the driver package, as did Paul B suggest in one case. But I have no idea how to do that. Here is the driver package of the wifi adapter: www.asus.com/uk/Networking/PCEN53/HelpDesk_Download/ My system is as following: OS: ubuntu 14.04 LTS wi-fi card: Asus PCE-N53 motherboard: Asus KCMA-D8 processor: AMD Opteron 4228 HE kernel: 3.13.0-32-generic Following this info from chili555 in here, below are some extra info about my system: lspci -nn | grep 0280 gives 04:00.0 Network controller [0280]: Ralink corp. RT5592 PCI2 Wireless Network Adapater [1814:5592] and sudo apt-get install linux-headers-generic returns linux-headers-generic is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. If this is a kernel version (I have 3.13.0-32-generic) incompatibility issue with the driver as chilli555 suggests (the README file in the driver package says indeed it is compatible with kernel 2.6), how could one trick this around to make it work? that should be possible right? On ubuntu forums, the patches proposed dont work (leads the computer to freeze). Basically: is there anybody out there who has ever been able to make a PCE-N53 work on Ubuntu 14.04 LTS (kernel 3.13)? how shall I edit the driver package to make it work for my kernel?

  Read the article

• cannot make ubuntu 64-bit v12.04 install work

  - by honestann

  I decided it was time to update my ubuntu (single boot) computer from 64-bit v10.04 to 64-bit v12.04. Unfortunately, for some reason (or reasons) I just can't make it work. Note that I am attempting a fresh install of 64-bit v12.04 onto a new 3TB hard disk, not an upgrade of the 1TB hard disk that contains my working 64-bit v10.04 installation. To perform the attempted install of v12.04 I unplug the SATA cable from the 1TB drive and plug it into the 3TB drive (to avoid risking damage to my working v10.04 installation). I downloaded the ubuntu 64-bit v12.04 install DVD ISO file (~1.6 GB) from the ubuntu releases webpage and burned it onto a DVD. I have downloaded the DVD ISO file 3 times and burned 3 of these installation DVDs (twice with v10.04 and once with my winxp64 system), but none of them work. I run the "check disk" on the DVDs at the beginning of the installation process to assure the DVD is valid. When installation completes and the system boots the 3TB drive, it reports "unknown filesystem". After installation on the 250GB drives, the system boots up fine. During every install I plug the same SATA cable (sda) into only one disk drive (the 3TB or one of the 250GB drives) and leave the other disk drives unconnected (for simplicity). It is my understanding that 64-bit ubuntu (and 64-bit linux in general) has no problem with 3TB disk drives. In the BIOS I have tried having EFI set to "enabled" and "auto" with no apparent difference (no success). I never bothered setting the BIOS to "non-EFI". I have tried partitioning the drive in a few ways to see if that makes a difference, but so far it has not mattered. Typically I manually create partitions something like this: 8GB /boot ext4 8GB swap 3TB / ext4 But I've also tried the following, just in case it matters: 8GB boot efi 8GB swap 8GB /boot ext4 3TB / ext4 Note: In the partition dialog I specify bootup on the same drive I am partitioning and installing ubuntu v12.04 onto. It is a VERY DANGEROUS FACT that the default for this always comes up with the wrong drive (some other drive, generally the external drive). Unless I'm stupid or misunderstanding something, this is very wrong and very dangerous default behavior. Note: If I connect the SATA cable to the 1TB drive that has been my ubuntu 64-bit v10.04 system drive for the past 2 years, it boots up and runs fine. I guess there must be a log file somewhere, and maybe it gives some hints as to what the problem is. I should be able to boot off the 1TB drive with the 3TB drive connected as a secondary (non-boot) drive and get the log file, assuming there is one and someone tells me the name (and where to find it if the name is very generic). After installation on the 3TB drive completes and the system reboots, the following prints out on a black screen: Loading Operating System ... Boot from CD/DVD : Boot from CD/DVD : error: unknown filesystem grub rescue> Note: I have two DVD burners in the system, hence the duplicate line above. Note: I install and boot 64-bit ubuntu v12.04 on both of my 250GB in this same system, but still cannot make the 3TB drive boot. Sigh. Any ideas? ========== motherboard == gigabyte 990FXA-UD7 CPU == AMD FX-8150 8-core bulldozer @ 3.6 GHz RAM == 8GB of DDR3 in 2 sticks (matched pair) HDD == seagate 3TB SATA3 @ 7200 rpm (new install 64-bit v12.04 FAILS) HDD == seagate 1TB SATA3 @ 7200 rpm (64-bit v10.04 WORKS for two years) HDD == seagate 250GB SATA2 @ 7200 rpm (new install 64-bit v12.04 WORKS) HDD == seagate 250GB SATA2 @ 7200 rpm (new install 64-bit v12.04 WORKS) GPU == nvidia GTX-285 ??? == no overclocking or other funky business USB == external seagate 2TB HDD for making backups DVD == one bluray burner (SATA) DVD == one DVD burner (SATA) 64-bit ubuntu v10.04 has booted and run fine on the seagate 1TB drive for 2 years.

  Read the article

• Enabling OUD Entry Cache for large static groups

  - by Sylvain Duloutre

  Oracle Unified Directory can take advantage of several caches to improve performances. especially the so-called database cache and the file system cache. In addition to that, it is possible to use an entry cache to cache LDAP entries. By default, the entry cache is not used. In specific deployements involving large static groups, it may worth loading the group entries to the entry cache to speed up group membership and group-based aci evaluation. To do so, run the following commands: First, specify which entries should reside in the entry cache. In the commad below, only entries matching the LDAP filter " (|(objctclass=groupOfNames)(objectclass=groupOfUniqueNames)) " will be stored in the entry cache. dsconfig set-entry-cache-prop \          --cache-name FIFO \          --add include-filter:\(\|\(objctclass=groupOfNames\)\(objectclass=groupOfUniqueNames\)\)          --port <ADMIN_PORT> \          --bindDN cn=Directory\ Manager \          --bindPassword ****** \          --no-prompt Then enable the entry cache: dsconfig set-entry-cache-prop \          --cache-name FIFO \          --set enabled:true \          --port <ADMIN_PORT> \          --bindDN cn=Directory\ Manager \          --bindPassword ****** \          --no-prompt In addition to that, you can control how much memory the entry cache can use: oud@s96sec1d0-v3:/application/oud : dsconfig -X -n -p <ADMIN PORT> -D "cn=Directory Manager" -w <password> get-entry-cache-prop --cache-name FIFO Property           : Value(s) -------------------:----------------------------------------------------------- cache-level        : 1 enabled            : true exclude-filter     : - include-filter     : (|(objctclass=groupOfNames)(objectclass=groupOfUniqueNames)) max-entries        : 2147483647 max-memory-percent : 90 You can change the max-entries amd max-memory-percent properties to control the entry cache size using the dsconfig set-entry-cache-prop command.

  Read the article

• default xna 4.0 gametime don´t works well for 2D physics

  - by EusKoder

  I am developing a game using Visual Studio 2010 and XNA 4.0, after advancing to some extent with the project (a platform based 2d platformer msdn starter kit) I got to test it on different computers with different hardware (CPU, graphics, etc.) and I found that the speed of movement object of the game is quite different, I implemented the PSK physics msdn that are based on time, /// <summary> /// Updates the player's velocity and position based on input, gravity, etc. /// </summary> public void ApplyPhysics(GameTime gameTime) { float elapsed = (float)gameTime.ElapsedGameTime.TotalSeconds; Vector2 previousPosition = Position; // Base velocity is a combination of horizontal movement control and // acceleration downward due to gravity. velocity.X += movement * MoveAcceleration * elapsed; velocity.Y = MathHelper.Clamp(velocity.Y + GravityAcceleration * elapsed, -MaxFallSpeed, MaxFallSpeed); velocity.Y = DoJump(velocity.Y, gameTime); // Apply pseudo-drag horizontally. if (IsOnGround) velocity.X *= GroundDragFactor; else velocity.X *= GroundDragFactor; //velocity.X *= AirDragFactor; // Prevent the player from running faster than his top speed. velocity.X = MathHelper.Clamp(velocity.X, -MaxMoveSpeed, MaxMoveSpeed); // Apply velocity. Position += velocity *elapsed; Position = new Vector2((float)Math.Round(Position.X), (float)Math.Round(Position.Y)); // If the player is now colliding with the level, separate them. HandleCollisions(gameTime); // If the collision stopped us from moving, reset the velocity to zero. if (Position.X == previousPosition.X) velocity.X = 0; if (Position.Y == previousPosition.Y) { velocity.Y = 0; jumpTime = 0.0f; } } tested eg with a PC (PC1) 2.13GHz Intel Core 2 6400 / ATI Radeon HD 4670 and another one: (pc2) 3.00GHz Intel Pentium D / Intel 82945G Express Chipset Family by displacement difference (moving x axis at supossed (position = velocity * gametime.ElapsedGameTime.TotalSeconds) constant velocity, for example) is 3 seconds in a total of 20 (example: moving pc1 player sprite 6000 pixels in the x-axis at 20 seconds and pc 2 runs the same distance in 17 ). Tested on a 3rd PC: i72700k / Gigabyte GTX 560 TI the results are even worse, after some time after starting the game gets like 3 times slower and showing the number of pixels in each frame moved in a debug window in the game (counting updatespersecond with counter variable for updates cuantity and gametime for counting a second show 63fps), it appears as if the number is always constant ( refreshments lose the Update method?). In this pc if I put the game in fullscreen during the course of the game, the effect of "go slow" is immediate and restore window mode sometimes yield returns to "normal" and sometimes not. Eventually I began to try a new project to test whether the movement is constant in different pc loading only one sprite and its position value in screen printing. Occur The same. I even tried moving a constant amount of pixels explicitly (position + = 5) and different speeds in different pc quantities of pixels moved in x time. I have the game loop as the default (fixedTimeStep=true;SynchronizeWithVerticalRetrace=true;). I've also tried turning off and creating another timestep as discussed in different post (eg http://gafferongames.com/game-physics/fix-your-timestep/ but i can´t achieve the desired result, move the same number of pixels in X seconds on different computers with windows. All pc used for tests use windows 7 enterprise pc1 == x86 the others are x64. The weirdest thing is that I find information about people describing the same problem and that I wear long nights of searches. Thanks for your help.

  Read the article

• help: cannot make ubuntu 64-bit v12.04 install work

  - by honestann

  I decided it was time to update my ubuntu (single boot) computer from 64-bit v10.04 to 64-bit v12.04. Unfortunately, for some reason (or reasons) I just can't make it work. Note that I am attempting a fresh install of 64-bit v12.04 onto a new 3TB hard disk, not an upgrade of the 1TB hard disk that has contained my 64-bit v10.04 installation. To perform the attempted install of v12.04 I unplug the SATA cable from the 1TB drive and plug it into the 3TB drive (to avoid risking damage to my working v10.04 installation). I downloaded the ubuntu 64-bit v12.04 install DVD ISO file (~1.6 GB) from the ubuntu releases webpage and burned it onto a DVD. I have downloaded the DVD ISO file 3 times and burned 3 of these installation DVDs (twice with v10.04 and once with my winxp64 system), but none of them work. I run the "check disk" on the DVDs at the beginning of the installation process to assure the DVD is valid. I also tried to install on two older 250GB seagate drives in the same computer. During every attempt I plug the same SATA cable (sda) into only one disk drive (the 3TB or one of the 250GB drives) and leave the other disk drives unconnected (for simplicity). Installation takes about 30 minutes on the 250GB drives, and about 60 minutes on the 3TB drive - not sure why. When I install on the 250GB drives, the install process finishes, the computer reboots (after the install DVD is removed), but I get a grub error 15. It is my understanding that 64-bit ubuntu (and 64-bit linux in general) has no problem with 3TB disk drives. In the BIOS I have tried having EFI set to "enabled" and "auto" with no apparent difference (no success). I have tried partitioning the drive in a few ways to see if that makes a difference, but so far it has not mattered. Typically I manually create partitions something like this: 8GB swap 8GB /boot ext4 3TB / ext4 But I've also tried the following, just in case it matters: 100MB boot efi 8GB swap 8GB /boot ext4 3TB / ext4 Note: In the partition dialog I specify bootup on the same drive I am partitioning and installing ubuntu v12.04 onto. It is a VERY DANGEROUS FACT that the default for this always comes up with the wrong drive (some other drive, generally the external drive). Unless I'm stupid or misunderstanding something, this is very wrong and very dangerous default behavior. Note: If I connect the SATA cable to the 1TB drive that has been my ubuntu 64-bit v10.04 system drive for the past 2 years, it boots up and runs fine. I guess there must be a log file somewhere, and maybe it gives some hints as to what the problem is. I should be able to boot off the 1TB drive with the 3TB drive connected as a secondary (non-boot) drive and get the log file, assuming there is one and someone tells me the name (and where to find it if the name is very generic). After installation on the 3TB drive completes and the system reboots, the following prints out on a black screen: Loading Operating System ... Boot from CD/DVD : Boot from CD/DVD : error: unknown filesystem grub rescue Note: I have two DVD burners in the system, hence the duplicate line above. The same install and reboot on the 250GB drives generates "grub error 15". Sigh. Any ideas? ========== motherboard == gigabyte 990FXA-UD7 CPU == AMD FX-8150 8-core bulldozer @ 3.6 GHz RAM == 8GB of DDR3 in 2 sticks (matched pair) HDD == seagate 3TB SATA3 @ 7200 rpm (new install 64-bit v12.04) HDD == seagate 1TB SATA3 @ 7200 rpm (current install 64-bit v10.04) GPU == nvidia GTX-285 ??? == no overclocking or other funky business USB == external seagate 2TB HDD for making backups DVD == one bluray burner (SATA) DVD == one DVD burner (SATA) The current ubuntu 64-bit v10.04 system boots and runs fine on a seagate 1TB.

  Read the article

• Iron Speed Designer 7.0 - the great gets greater!

  - by GGBlogger

  For Immediate Release Iron Speed, Inc. Kelly Fisher +1 (408) 228-3436 [email protected] http://www.ironspeed.com       Iron Speed Version 7.0 Generates SharePoint Applications New! Support for Microsoft SharePoint speeds application generation and deployment   San Jose, CA – June 8, 2010. Software development tools-maker Iron Speed, Inc. released Iron Speed Designer Version 7.0, the latest version of its popular Web 2.0 application generator. Iron Speed Designer generates rich, interactive database and reporting applications for .NET, Microsoft SharePoint and the Cloud.    In addition to .NET applications, Iron Speed Designer V7.0 generates database-driven SharePoint applications. The ability to quickly create database-driven applications for SharePoint eliminates a lot of work, helping IT departments generate productivity-enhancing applications in just a few hours.  Generated applications include integrated SharePoint application security and use SharePoint master pages.    “It’s virtually impossible to build database-driven application in SharePoint by hand. Iron Speed Designer V7.0 not only makes this possible, the tool makes it easy.” – Razi Mohiuddin, President, Iron Speed, Inc.     Integrated SharePoint application security Generated applications include integrated SharePoint application security. SharePoint sites and their groups are used to retrieve security roles. Iron Speed Designer validates the user against a Microsoft SharePoint server on your network by retrieving the logged in user’s credentials from the SharePoint Context.    “The Iron Speed Designer generated application integrates seamlessly with SharePoint security, removing the hassle of designing, testing and approving your own security layer.” -Michael Landi, Solutions Architect, Light Speed Solutions     SharePoint Solution Packages Iron Speed Designer V7.0 creates SharePoint Solution Packages (WSPs) for easy application deployment. Using the Deployment Wizard, a single application WSP is created and can be deployed to your SharePoint server.   “Iron Speed Designer is the first product on the market that allows easy and painless deployment of database-driven .NET web applications inside the SharePoint environment.” -Bryan Patrick, Developer, Pseudo Consulting     SharePoint master pages and themes In V7.0, generated applications use SharePoint master pages and contain the same content as other SharePoint pages. Generated applications use the current SharePoint color scheme and display standard SharePoint navigation controls on each page.   “Iron Speed Designer preserves the look and feel of the SharePoint environment in deployed database applications without additional hand-coding.” -Kirill Dmitriev, Software Developer, Iron Speed, Inc.     Iron Speed Designer Version 7.0 System Requirements Iron Speed Designer Version 7.0 runs on Microsoft Windows 7, Windows Vista, Windows XP, and Windows Server 2003 and 2008. It generates .NET Web applications for Microsoft SQL Server, Oracle, Microsoft Access and MySQL. These applications may be deployed on any machine running the .NET Framework. Iron Speed Designer supports Microsoft SharePoint 2007 and Windows SharePoint Services (WSS3). Find complete information about Iron Speed Designer Version 7.0 at www.ironspeed.com.     About Iron Speed, Inc. Iron Speed is the leader in enterprise-class application generation. Our software development tools generate database and reporting applications in significantly less time and cost than hand-coding. Our flagship product, Iron Speed Designer, is the fastest way to deliver applications for the Microsoft .NET and software-as-a-service cloud computing environments.   With products built on decades of experience in enterprise application development and large-scale e-commerce systems, Iron Speed products eliminate the need for developers to choose between "full featured" and "on schedule."   Founded in 1999, Iron Speed is well funded with a capital base of over $20M and strategic investors that include Arrow Electronics and Avnet, as well as executives from AMD, Excelan, Onsale, and Oracle. The company is based in San Jose, Calif., and is located online at www.ironspeed.com.

  Read the article

• 12.04 installation started to black screen during boot today

  - by Cedric

  NOTE: Most of this question is now irrelevant. UPDATE 3 summarizes the problem as it stands. I've been running 12.04 on my Lenovo laptop for one month now (updated from 11.04), and I have not had any significant problem until today. This morning, when I boot, I pass the Grub screen, then I get to the purple loading screen with dots as usual, then for some reason I got to the terminal login, with no GUI. startx gives me a black screen. Ctrl+F7-F8 didn't help either. It's similar to: After the update today no graphical interface anymore - 12.04 I followed the instructions at the end, to flush the ATI drivers (which I had installed), and fall back to the community drivers. That made me lose the login! Now I just get a black screen after the Ubuntu loading screen. I can still access the console through recovery, and I've gotten into VESA mode once or twice (not reproducible, for some reason). I've tried various permutations of xorg.conf, without success. Xorg -configure fails for now, though I might be able to get it to work. apt-get update/upgrade doesn't improve anything either. However, both Windows and the 12.04 Live CD still work beautifully, and I know that all my data is still there. Is there any way that I could somehow take the configuration from the Live CD and roll with it? I know that I could reinstall, but that sucks, frankly, especially given that there's no straight-forward way of keeping the home (which, incidentally, is unaccessible from the Live CD) Thank you. Update: it seems that the fglrx drivers are still active, even after I've --purged them. From Xorg.0.log: [ 18.235] (WW) fglrx(0): *********************************************************** [ 18.235] (WW) fglrx(0): * DRI initialization failed * [ 18.235] (WW) fglrx(0): * kernel module (fglrx.ko) may be missing or incompatible * [ 18.235] (WW) fglrx(0): * 2D and 3D acceleration disabled * [ 18.235] (WW) fglrx(0): *********************************************************** [ 18.235] Fatal server error: [ 18.235] AddScreen/ScreenInit failed for driver 0 There's also a mention of the "fbdev" module. What is it? PARTIALLY SOLVED: I've undone the damage from the fglrx purge. I'm still mystified as to why uninstalling the packages didn't kill fglrx entirely, but I've now recovered the prompt. The solution to the DRI initialization error was to add radeon.modeset=0 to the GRUB boot options. So I'm back to being dropped to a prompt without any GUI. startx gives me a bunch of messages, though no obvious errors. I have little reason to suspect the video drivers, as they worked fine before today. There is no apparent error message in any of the log files. UPDATE: When I startx, I get an error, Plymounth command failed mountall: Disconnected from Plymouth This is all over the Internet, but I have not found anything that works for me yet. UPDATE 3: If I press ESC during boot, the splash screen (Plymouth!) disappears, and I no longer have any error from Plymouth. The last error message is: Stopping mount filesystems on boot I can then Ctrl+Alt+F1 to get the TTY1, but startx still does not work. Sadly, the Internet knows nothing about this error message, and neither do I. Help!

  Read the article

< Previous Page | 63 64 65 66 67 68 69 70 71 72 73  | Next Page >