Search Results

Search found 12281 results on 492 pages for 'ip blocking'.

Page 69/492 | < Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >

• Mac OS X 10.6 assign mapped IP to Windows 7 VM in Parallels

  - by Alex

  I'm trying to assign a mapped IP address to a Windows 7 VM. I have setup running in Parallels 5 in wireless bridged networking mode. The problem I am having is that it looks like the VM is actually broadcasting the MAC address of the host machine and thus causing a clash of IP addresses on the network. This is my current setup: Macbook Pro :~ ifconfig -a lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 inet 127.0.0.1 netmask 0xff000000 gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280 stf0: flags=0<> mtu 1280 en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 00:26:b0:df:31:b4 media: autoselect status: inactive supported media: none autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,flow-control> 10baseT/UTP <full-duplex,hw-loopback> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,flow-control> 100baseTX <full-duplex,hw-loopback> 1000baseT <full-duplex> 1000baseT <full-duplex,flow-control> 1000baseT <full-duplex,hw-loopback> fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078 lladdr 00:26:b0:ff:fe:df:31:b4 media: autoselect <full-duplex> status: inactive supported media: autoselect <full-duplex> en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::226:bbff:fe0a:59a1%en1 prefixlen 64 scopeid 0x6 inet 192.168.1.97 netmask 0xffffff00 broadcast 192.168.1.255 ether 00:26:bb:0a:59:a1 media: autoselect status: active supported media: autoselect vnic0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet 192.168.1.81 netmask 0xffffff00 broadcast 192.168.1.255 ether 00:1c:42:00:00:08 media: autoselect status: active supported media: autoselect vnic1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet 10.37.129.2 netmask 0xffffff00 broadcast 10.37.129.255 ether 00:1c:42:00:00:09 media: autoselect status: active supported media: autoselect Windows 7: :~ ipconfig -all Windows IP Configuration Host Name . . . . . . . . . . . . : Alex-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Parallels Ethernet Adapter Physical Address. . . . . . . . . : 00-1C-42-B8-E7-B4 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Teredo Tunneling Adapter Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{ACAC7EBB-5E5F-4F53-AFD9-E6EAEEA0FEE2}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Billion Bipac 7200 modem router: In DHCP server settings have the following two mapping entries. alex-macbook-win7 00:1c:42:00:00:08 192.168.1.98 alex-macbook 00:26:bb:0a:59:a1 192.168.1.97 The problem I have is that when the VM starts up it gets assigned the 192.168.1.97 address instead of the .98 address and thus networking on the host stops working as it says there is a clash. I have tried removing the mapping for "alex-macbook" which results in the guest machine being assigned a normal DHCP address and NOT the one that is in the mapping of the router.

  Read the article

• Can ping IP address and nslookup hostname but cannot ping hostname

  - by Puddingfox

  I have a DNS server set up on one of my machines using BIND 9.7 Everything works fine with it. On my Windows 7 desktop, I have statically-assigned all network values. I have one DNS server set -- my DNS server. On my desktop, I can ping a third machine by IP fine. I can nslookup the hostname of the third machine fine. When I ping the hostname, it says it cannot find the host. / C:\Users\James>nslookup icecream Server: cake.my.domain Address: xxx.xxx.6.3 Name: icecream.my.domain Address: xxx.xxx.6.9 C:\Users\James>ping xxx.xxx.6.9 Pinging xxx.xxx.6.9 with 32 bytes of data: Reply from xxx.xxx.6.9: bytes=32 time<1ms TTL=255 Reply from xxx.xxx.6.9: bytes=32 time<1ms TTL=255 Reply from xxx.xxx.6.9: bytes=32 time<1ms TTL=255 Reply from xxx.xxx.6.9: bytes=32 time<1ms TTL=255 Ping statistics for xxx.xxx.6.9: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\Users\James>ping icecream Ping request could not find host icecream. Please check the name and try again. I have also specified the search domain as my.domain xxx.xxx and my.domain substituted for security Why can I not ping by hostname? I also can not ping using the FQDN. The problem is that this problem is shared by all applications that resolve hostnames. I cannot use PuTTY to SSH to my machines by hostname; only by IP

  Read the article

• Can ping IP address and nslookup hostname but cannot ping hostname

  - by jao

  On a windows 2003 server I can nslookup www.google.com which returns Server: localhost Address: 127.0.0.1 Non-authoritative answer: Name: www.l.google.com Addresses: 74.125.79.104, 74.125.79.147, 74.125.79.99 Aliases: www.google.com I can then ping 74.125.79.104: Pinging 74.125.79.104 with 32 bytes of data: Reply from 74.125.79.104: bytes=32 time=16ms TTL=54 Reply from 74.125.79.104: bytes=32 time=32ms TTL=54 Reply from 74.125.79.104: bytes=32 time=15ms TTL=54 Reply from 74.125.79.104: bytes=32 time=15ms TTL=54 Ping statistics for 74.125.79.104: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 15ms, Maximum = 32ms, Average = 19ms But I cannot ping www.google.com: Ping request could not find host www.google.com. Please check the name and try again. (this one is different from the other question in that this one has a TLD, it is not a local domain.) Update: I am running a dns server at localhost (127.0.0.1). Even when I change it to use for example opendns, it still can nslookup hostname and ping ip address, but not ping hostname. So what is wrong? Update 2: here is the ipconfig /all result: Windows IP Configuration Host Name . . . . . . . . . . . . : SERVER Primary Dns Suffix . . . . . . . : NETWORK.local Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : NETWORK.local Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2 Physical Address. . . . . . . . . : 00-0F-1F-56-3B-AA DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.7.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.7.1 DNS Servers . . . . . . . . . . . : 127.0.0.1 Update 3: Thanks everyone for their help and suggestions. I appreciate that. Ipconfig /flushdns returns: Sucessfully flushed the DNS resolver cache Ipconfig /displaydns returns: 2.7.168.192.in-addr.arpa ---------------------------------------- Record Name . . . . . : 2.7.168.192.in-addr.arpa. Record Type . . . . . : 12 Time To Live . . . . : 0 Data Length . . . . . : 4 Section . . . . . . . : Answer PTR Record . . . . . : webserver.mydomainname.com 1.0.0.127.in-addr.arpa ---------------------------------------- Record Name . . . . . : 1.0.0.127.in-addr.arpa. Record Type . . . . . : 12 Time To Live . . . . : 0 Data Length . . . . . : 4 Section . . . . . . . : Answer PTR Record . . . . . : localhost Update 4: Wireshark shows the following: 3 11.540542 208.67.220.220 192.168.7.2 DNS Standard query response A 74.125.79.99 A 74.125.79.104 A 74.125.79.147 6 42.056794 192.168.7.2 192.168.7.255 NBNS Name query NB WWW.GOOGLE.COM<00> which is weird: when I ping, it sends a packet to 192.168.7.255 instead of asking the DNS server for an address

  Read the article

• ipvsadm lists a few hosts by IP only, rest by name

  - by dmourati

  We use keepalived to manage our Linux Virtual Server (LVS) load balancer. The LVS VIPs are setup to use a FWMARK as configured in iptables. virtual_server fwmark 300000 { delay_loop 10 lb_algo wrr lb_kind NAT persistence_timeout 180 protocol TCP real_server 10.10.35.31 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.31" misc_timeout 30 } } real_server 10.10.35.32 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.32" misc_timeout 30 } } real_server 10.10.35.33 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.33" misc_timeout 30 } } real_server 10.10.35.34 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.34" misc_timeout 30 } } } http://www.austintek.com/LVS/LVS-HOWTO/HOWTO/LVS-HOWTO.fwmark.html [root@lb1 ~]# iptables -L -n -v -t mangle Chain PREROUTING (policy ACCEPT 182G packets, 114T bytes) 190M 167G MARK tcp -- * * 0.0.0.0/0 w1.x1.y1.4 multiport dports 80,443 MARK set 0x493e0 62M 58G MARK tcp -- * * 0.0.0.0/0 w1.x1.y2.4 multiport dports 80,443 MARK set 0x493e0 [root@lb1 ~]# ipvsadm -L IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn FWM 300000 wrr persistent 180 -> 10.10.35.31:0 Masq 24 1 0 -> dis2.domain.com:0 Masq 24 3 231 -> 10.10.35.33:0 Masq 24 0 208 -> 10.10.35.34:0 Masq 24 0 0 At the time the realservers were setup, there was a misconfigured dns for some hosts in the 10.10.35.0/24 network. Thereafter, we fixed the DNS. However, the hosts continue to show up as only their IP numbers (10.10.35.31,10.10.35.33,10.10.35.34) above. [root@lb1 ~]# host 10.10.35.31 31.35.10.10.in-addr.arpa domain name pointer dis1.domain.com. OS is CentOS 6.3. Ipvsadm is ipvsadm-1.25-10.el6.x86_64. kernel is kernel-2.6.32-71.el6.x86_64. Keepalived is keepalived-1.2.7-1.el6.x86_64. How can we get ipvsadm -L to list all realservers by their proper hostnames?

  Read the article

• Changing externally visible IP on a multi-IP router?

  - by AlternateZ

  I work at a public library and I'm trying to configure OCLC's EzProxy software. I've run into a problem and I think it's related to our network config. I'm punching above my weight here a little so I need some help. I think I'm trying to configure a 1:1 NAT, but not sure how or if our hardware supports it. The EzProxy machine is on an internet line which supports multiple external IPs. Our router is a Billion BiGuard30. There's another server on this line, let's say its IP is x.x.x.9. The EzProxy machine is x.x.x.11 I've set up port forwarding from x.x.x.11 on the http ports to the EzProxy machine. Trying to browse to x.x.x.11 from an external PC works fine - we get to the EzProxy page we are serving. However, if we go to something like WhatIsMyIP from the EzProxy machine, it says that its IP is x.x.x.9. This causes problems with our user authentication software. How do we make the rest of the internet see that the machine is x.x.x.11? There doesnt seem to be any "outbound port forwarding" on the Billion router, nor is there any "1:1 NAT" options in its config webpage. The EzProxy machine is running Ubuntu 12.04, if that helps.

  Read the article

• Distribute IP packets accross different NIC queues with MSI (Message Signalled Interrupts)

  - by Ansis Atteka

  NetXtreme II BCM5709 Gigabit Ethernet NIC supports MSI feature (Message Signaled Interrupts) and it has 8 queues. Each queue has its own Interrupt handler in /proc/interrupts. What I am trying to accomplish is to tell NIC which packets should go to which queue. Questions: Is it possible to manually specify which IP packets should go to which queue by encapsulated protocol type (e.g. IPsec packets go in one queue, while TCP packets go in another queue)? If it is possible - how can I do it under Linux? If it is not possible - should I look at MSI-X capable NIC cards to solve this problem? More details: We have one Interface that is terminating IPSec and forwarding/terminating TCP connections. The IPSec packet decryption is inlined (this means that decryption is done under the same ksoftirqd/X context). We are trying to find out if we will be able to improve total performance if IPSec packets will be scheduled on another CPU than TCP packets. One more limitation is that IPSec code is not MP-safe, hence I can not run it under more than one ksoftirqd/X. By default it seems that packets are distributed/hashed by source IP over the 8 NIC queues. The bottleneck is IPSec that chokes out TCP traffic while it is decrypting/encrypting IPSec packets at ~100% CPU. OS is Ubuntu 10.10 (2.6.32-27-server) and NIC is Broadcom BCM5709.

  Read the article

• IIS8 behind a VPN + Windows Server 2012 - how to properly bind IP+Port

  - by ryugen

  This is my first question so I hope I'm going to give you enough information. I'm running Windows Server 2012 within the Hyper-V environment of my Windows 8 machine. Within Windows Server 2012 I'm running a VPN tool based on openVPN to hide my real IP. When I run IIS8 with the VPN disconnected it works flawlessly through the Internet (port 80 forwarded correctly). But as soon as I connect to the VPN I can't reach my site through the domain anymore. Now I tried basically everything I know which is why I'm asking you guys. I tried binding IIS8 to the IP of my virtual ethernet card. I tried changing the priority of the NIC through the "Network and sharing center" via the advanced tab. I used ipconfig /flushdns in case there was something wrong in the DNS handling. Hell, I even turned off the Windows firewall. I also used a port scanner to verify the problem. The webserver is reachable on port 80 with VPN disconnected and immediately gets unreachable on connect. Theoretically both IPs (my regular one AND the VPN) should be reachable or at least not impair the other one right? Do you have any other suggestion? Do I have to route something somewhere somehow?

  Read the article

• Apache 403 Forbidden Error when accessing local web server using local IP address

  - by amjo324

  I have an odd problem when attempting to browse to pages stored on a local web server (Apache 2.2). The pages are served as expected when I browse to localhost or 127.0.0.1 on port 80. Yet when I attempt to browse to the same pages by referencing the local IP address (192.168.x.x), I receive a HTTP 403 (Forbidden) error. In essence, http://localhost:80 works but 192.168.x.x:80 doesn't even though I'm specifying the IP of the local machine. You may be thinking "who cares? just use localhost". However, this is the first step in troubleshooting why I cannot remotely access these pages from different hosts on my LAN. I'm presuming this can't be a firewall issue as I'm only connecting to the local machine. Even so, I verified there was no iptables rules that could be having an effect. I've checked the Apache error logs and the corresponding line of relevance is: [Sat Oct 19 07:38:35 2013] [error] [client 192.168.x.x] client denied by server configuration: /var/www/ I've inspected most of the apache config files and they don't appear to differ from what you would expect with a default install. I can't see anything in apache2.conf that would be a problem and httpd.conf is an empty file. This is an excerpt from /etc/apache2/sites-enabled/000-default: <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> Any insight as to where I can look next to find a solution ? Thanks in advance.

  Read the article

• VPN - local and remote networks IP collision

  - by Guido García

  I have created a VPN connection in Windows using the New Network Connection wizard that comes with Windows. It works without problems in most places, but there is one concrete place where, despite the connection to the remote public IP works fine, it is not able to validate the login/password and establish the VPN connection. In this place, the network is 10.0.0.x (the same I use in other places where I am able to connect). The remote network is 192.168.x.x, so I suspect there is some kind of IP collision, because before connecting, a traceroute to i.e. 192.168.0.40 does not fail. 1 4 ms 1 ms 1 ms LINKSYS [10.0.0.1] 2 5 ms 1 ms 1 ms 172.26.27.1 3 4 ms 5 ms 3 ms 192.168.1.100 ... (more) I can't modify the local network further than the first router (10.0.0.1). That is the only different I've found so far. Any idea about how to solve it? Thank you.

  Read the article

• Kickstart CentOS 6 prompting for TCP/IP with network set to DHCP

  - by Andy Shinn

  I am trying to stop my kickstart CentOS install prompting me for TCP/IP information. After I click through this prompt (keeping IPv4 and IPv6 to their defaults) the installation continues and completes just fine. Below is my kickstart file: # Andy's super awesome VM kickstart file install url --url=http://mirrors.kernel.org/centos/6/os/x86_64 lang en_US.UTF-8 keyboard us text %include /tmp/network.ks rootpw --iscrypted $6$RA8DyrNTsVJkGIgY$ohZ62HHiOjNnn1yDMZlIu3lQ63D3plGPcbVZtPKE8Oq6Z.IGUgN.kNLkxs/ZymZuluRDWsW2eey5zLOl2G3mp. firewall --service=ssh authconfig --enableshadow --passalgo=sha512 selinux --disabled timezone America/Los_Angeles bootloader --location=mbr --driveorder=vda --append="crashkernel=auto rhgb quiet" # The following is the partition information you requested # Note that any partitions you deleted are not expressed # here so unless you clear all partitions first, this is # not guaranteed to work zerombr clearpart --all --drives=vda --initlabel part /boot --fstype=ext4 --size=500 part pv.253002 --grow --size=1 volgroup vg1 --pesize=4096 pv.253002 logvol / --fstype=ext4 --name=lv_root --vgname=vg1 --grow --size=1024 --maxsize=51200 logvol swap --name=lv_swap --vgname=vg1 --grow --size=4032 --maxsize=4032 repo --name="CentOS" --baseurl=http://mirrors.kernel.org/centos/6/os/x86_64 --cost=100 repo --name="Puppet Labs Products" --baseurl=http://yum.puppetlabs.com/el/6/products/x86_64 repo --name="Puppet Labs Dependencies" --baseurl=http://yum.puppetlabs.com/el/6/dependencies/x86_64 repo --name="EyeFi" --baseurl=http://flexo.eye.fi/6/eye-fi-api %packages @core @server-policy puppet facter %end %pre --erroronfail #!/bin/bash for x in `cat /proc/cmdline`; do case $x in SERVERNAME*) eval $x echo "network --onboot yes --device eth0 --bootproto dhcp --hostname ${SERVERNAME}.eye.fi" /tmp/network.ks ;; esac; done %end %post puppet agent --waitforcert 10 --onetime --no-daemon --pluginsync --server puppet.eye.fi %end reboot My kernel arguments are in this following virt-install command that I use to start the install: virt-install -n zabbix -r 2048 --vcpus=2 -l http://mirrors.kernel.org/centos/6/os/x86_64 --disk /dev/vg_inf1/zabbix --network bridge=br85 --initrd-inject=/home/ashinn/vm_kickstart --extra-args "ks=file:/vm_kickstart SERVERNAME=zabbix" --autostart During the install, I can pull up a console on the second terminal and verify the contents of /tmp/network.ks are: network --onboot=yes --bootproto=dhcp --ipv6=auto --hostname=jenkins2.mydomain.com Why might Anaconda be prompting for the TCP/IP settings when they are already set to DHCP?

  Read the article

• A Question about using jython when run a receving socket in python

  - by abusemind

  Hi, I have not a lot of knowledge of python and network programming. Currently I am trying to implement a simple application which can receive a text message sent by the user, fetch some information from the google search api, and return the results via text message to the user. This application will continue to listening to the users messages and reply immediately. How I get the text short message sent by the user? It's a program named fetion from the mobile supplier in China. The client side fetion, just like a instant communication tool, can send/receive messages to/from other people who are using mobile to receive/send SMS. I am using a open source python program that simulates the fetion program. So basically I can use this python program to communate with others who using cell phone via SMS. My core program is based on java, so I need to take this python program into java environment. I am using jython, and now I am available to send messages to users by some lines of java codes. But the real question is the process of receving from users via SMS. In python code, a new thread is created to continuously listen to the user. It should be OK in Python, but when I run the similar process in Jython, the following exception occurs: Exception in thread Thread:Traceback (most recent call last): File "D:\jython2.5.1\Lib\threading.py", line 178, in _Thread__bootstrap self.run() File "<iostream>", line 1389, in run File "<iostream>", line 1207, in receive File "<iostream>", line 1207, in receive File "<iostream>", line 150, in recv File "D:\jython2.5.1\Lib\select.py", line 223, in native_select pobj.register(fd, POLLIN) File "D:\jython2.5.1\Lib\select.py", line 104, in register raise _map_exception(jlx) error: (20000, 'socket must be in non-blocking mode') The line 150 in the python code is as follows: def recv(self,timeout=False): if self.login_type == "HTTP": time.sleep(10) return self.get_offline_msg() pass else: if timeout: infd,outfd,errfd = select([self.__sock,],[],[],timeout)//<---line 150 here else: infd,outfd,errfd = select([self.__sock,],[],[]) if len(infd) != 0: ret = self.__tcp_recv() num = len(ret) d_print(('num',),locals()) if num == 0: return ret if num == 1: return ret[0] for r in ret: self.queue.put(r) d_print(('r',),locals()) if not self.queue.empty(): return self.queue.get() else: return "TimeOut" Because of I am not very familiar with python, especially the socket part, and also new in Jython use, I really need your help or only advice or explanation. Thank you very much!

  Read the article

• kvm-over-ip, multiple machines per cable run

  - by Sirex

  I'm looking at getting a kvm-over-ip setup for a server room. Typically these devices have 16 or so cat5 leads that come out of them and then a convertor that converts each cat5 into a vga & ps2 pair. Can you run one cable from the unit into a switch, and then leads from the switch into each machine ? I have several machines on the other side of the server room that i'd like to have avaliable but i dont want to run 16 cables to them. I'm thinking this should be possible being IP layer and all, but as each device normally has its own cable out the back of the kvm unit i'm not certain. Perhaps the kvm's rear ports act essentially like a switch anyway in which case it should work, or perhaps if i run all 16 cables into a seperate switch right next to it and aggregate the ports together, run one cable to a switch on the other side of the room with similar number of ports agregated together, then use that switch to plug each macine into ? I'm fairly sure this is possible, but i just want to check before i shell out the cash as i've never tried it.

  Read the article

• Two servers, two domains, one ip. mod_proxy beginner

  - by Gutsav

  I run two virtual web servers (both running apache2 on debian). I have just one external IP, but two domains, and I want a domain going to each of the servers. I've understood that I need a Reverse Proxy, and I enabled both the mod_proxy and the mod_proxy_http modules on the "primary server". Do I need to enable anything on the "secondary server"? I also understood that I need to write some things in a virtual host file, but what? On the primary server, I have a virtual host file for one of the domains, and some for subdomains. I want domain1.tld to go to the primary server (port 80 is forwarded to it, so that works) and domain2.tld to go to the other server (internal ip 192.168.0.x). No ports needs to be forwarded to it, right? So, what to add and in which virtual host file? Or a new one? Other questions suggest adding ProxyPass and ProxyPassReverse, but I'm lost anyway, and I just don't understand the apache documentation. Thanks in advance

  Read the article

• IP address numbers in MySQL subquery

  - by Iain Collins

  I have a problem with a subquery involving IPV4 addresses stored in MySQL (MySQL 5.0). The IP addresses are stored in two tables, both in network number format - e.g. the format output by MySQL's INET_ATON(). The first table ('events') contains lots of rows with IP addresses associated with them, the second table ('network_providers') contains a list of provider information for given netblocks. events table (~4,000,000 rows): event_id (int) event_name (varchar) ip_address (unsigned 4 byte int) network_providers table (~60,000 rows): ip_start (unsigned 4 byte int) ip_end (unsigned 4 byte int) provider_name (varchar) Simplified for the purposes of the problem I'm having, the goal is to create an export along the lines of: event_id,event_name,ip_address,provider_name If do a query along the lines of either of the following, I get the result I expect: SELECT provider_name FROM network_providers WHERE INET_ATON('192.168.0.1') >= network_providers.ip_start ORDER BY network_providers.ip_start DESC LIMIT 1 SELECT provider_name FROM network_providers WHERE 3232235521 >= network_providers.ip_start ORDER BY network_providers.ip_start DESC LIMIT 1 That is to say, it returns the correct provider_name for whatever IP I look up (of course I'm not really using 192.168.0.1 in my queries). However, when performing this same query as a subquery, in the following manner, it doesn't yield the result I would expect: SELECT event.id, event.event_name, (SELECT provider_name FROM network_providers WHERE event.ip_address >= network_providers.ip_start ORDER BY network_providers.ip_start DESC LIMIT 1) as provider FROM events Instead the a different (incorrect) value for network_provider is returned - over 90% (but curiously not all) values returned in the provider column contain the wrong provider information for that IP. Using event.ip_address in a subquery just to echo out the value confirms it contains the value I'd expect and that the subquery can parse it. Replacing event.ip_address with an actual network number also works, just using it dynamically in the subquery in this manner that doesn't work for me. I suspect the problem is there is something fundamental and important about subqueries in MySQL that I don't get. I've worked with IP addresses like this in MySQL quite a bit before, but haven't previously done lookups for them using a subquery. The question: I'd really appreciate an example of how I could get the output I want, and if someone here knows, some enlightenment as to why what I'm doing doesn't work so I can avoid making this mistake again. Notes: The actual real-world usage I'm trying to do is considerably more complicated (involving joining two or three tables). This is a simplified version, to avoid overly complicating the question. Additionally, I know I'm not using a between on ip_start & ip_end - that's intentional (the DB's can be out of date, and such cases the owner in the DB is almost always in the next specified range and 'best guess' is fine in this context) however I'm grateful for any suggestions for improvement that relate to the question. Efficiency is always nice, but in this case absolutely not essential - any help appreciated.

  Read the article

• VPN - local and remote networks IP collision

  - by Guido García

  I have created a VPN connection in Windows using the New Network Connection wizard that comes with Windows. It works without problems in most places, but there is one concrete place where, despite the connection to the remote public IP works fine, it is not able to validate the login/password and establish the VPN connection. In this place, the network is 10.0.0.x (the same I use in other places where I am able to connect). The remote network is 192.168.x.x, so I suspect there is some kind of IP collision, because before connecting, a traceroute to i.e. 192.168.0.40 does not fail. 1 4 ms 1 ms 1 ms LINKSYS [10.0.0.1] 2 5 ms 1 ms 1 ms 172.26.27.1 3 4 ms 5 ms 3 ms 192.168.1.100 ... (more) I can't modify the local network further than the first router (10.0.0.1). That is the only different I've found so far. Any idea about how to solve it? Thank you.

  Read the article

• IPTABLE & IP-routed netwok solution for HOST net and VM's subnet

  - by Daniel

  I've got ProxmoxVE2.1 ruled KVM node on Debian and bunch of VM's guests machine. That is how my networking looks like: # network interface settings auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address 175.219.59.209 gateway 175.219.59.193 netmask 255.255.255.224 post-up echo 1 > /proc/sys/net/ipv4/conf/eth0/proxy_arp And I've got two working subnet solution auto vmbr0 iface vmbr0 inet static address 10.10.0.1 netmask 255.255.0.0 bridge_ports none bridge_stp off bridge_fd 0 post-up ip route add 10.10.0.1/24 dev vmbr0 This way I can reach internet, to resolve outside hosts, update and download everything I need but can't reach one guest VM out of any other VM's inside my network. The second solution allows me to communicate between VM's: auto vmbr1 iface vmbr1 inet static address 10.10.0.1 netmask 255.255.255.0 bridge_ports none bridge_stp off bridge_fd 0 post-up echo 1 > /proc/sys/net/ipv4/ip_forward post-up iptables -t nat -A POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE post-down iptables -t nat -D POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE I can even NAT internal addresses: -t nat -I PREROUTING -p tcp --dport 789 -j DNAT --to-destination 10.10.0.220:345 My inexperienced mind is ready to double VM's net adapters: one for the first solution and another - for second (with slightly different adresses) but I'm pretty sure that it's a dumb way to resolve the problem and everything can be resolved via iptables/ip route rules that I can't create. I've tried a dozen of "wizard manuals" and "howto's" to mix both solution but without success. Looking for an advice (and good reading links for networking begginers).

  Read the article

• Linux port-based routing using iptables/ip route

  - by user42055

  I have the following setup: 192.168.0.4 192.168.0.6 192.168.0.1 +-----------+ +---------+ +----------+ |WORKSTATION|------| LINUX |------| GATEWAY | +-----------+ +---------+ +----------+ 192.168.150.10 | 192.168.150.9 +---------+ | VPN | +---------+ 192.168.150.1 WORKSTATION has a default route of 192.168.0.6 LINUX has a default route of 192.168.0.1 I am trying to use the gateway as the default route, but route port 80 traffic via the VPN. Based on what I read at http://www.linuxhorizon.ro/iproute2.html I have tried this: echo "1 VPN" >> /etc/iproute2/rt_tables sysctl net.ipv4.conf.eth0.rp_filter = 0 sysctl net.ipv4.conf.tun0.rp_filter = 0 sysctl net.ipv4.conf.all.rp_filter = 0 iptables -A PREROUTING -t mangle -i eth0 -p tcp --dport 80 -j MARK --set-mark 0x1 ip route add default via 192.168.150.9 dev tun0 table VPN ip rule add from all fwmark 0x1 table VPN When I run "tcpdump -i eth0 port 80" on LINUX, and open a webpage on WORKSTATION, I don't see the traffic go through LINUX at all. When I run a ping from WORKSTATION, I get this back from some packets: 92 bytes from 192.168.0.6: Redirect Host(New addr: 192.168.0.1) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 de91 0 0000 3f 01 4ed3 192.168.0.4 139.134.2.18 Is this why my routing is not working ? Do I need to put GATEWAY and LINUX on different subnets to prevent WORKSTATION being redirected to GATEWAY ? Do I need to use NAT at all, or can I do this with routing alone (which is what I want) ?

  Read the article

• Find routers IP address on the other side

  - by corsiKa

  Here's the basic setup of my network In this diagram: 1: The internet c: cable 2: Wireless router w: wireless connection 3: A win7 box with internet connection sharing enabled 4: A wireless router, but I'm only using its LAN capabilities to connect box 5 to the internet. 5: A win7 box, the computer I'm using to make this post. So its internet works just fine. Now if I'm on box 5, and I ping 192.168.1.1, I hit 4. If I'm on box 3 and I ping 192.168.1.1, I hit 2. Now obviously box 3 does not think 4's IP address is 192.168.1.1, or I wouldn't be able to connect to the internet. Okay, now that you know as much as I do about my network, here's my question: If I was on box 3, how would I determine the IP address of 4? Basically I'm running a webserver on box 5 and want to access this webserver on box 3 and other boxes. So that's the end goal. If there's other information there that can help, I'd appreciate it. Thanks!

  Read the article

• How to set a static route for an external IP address

  - by HorusKol

  Further to my earlier question about bridging different subnets - I now need to route requests for one particular IP address differently to all other traffic. I have the following routing in my iptables on our router: # Allow established connections, and those !not! coming from the public interface # eth0 = public interface # eth1 = private interface #1 (10.1.1.0/24) # eth2 = private interface #2 (129.2.2.0/25) iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -m state --state NEW ! -i eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o eth1 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth0 -o eth2 -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow outgoing connections from the private interfaces iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT # Allow the two private connections to talk to each other iptables -A FORWARD -i eth1 -o eth2 -j ACCEPT iptables -A FORWARD -i eth2 -o eth1 -j ACCEPT # Masquerade (NAT) iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE # Don't forward any other traffic from the public to the private iptables -A FORWARD -i eth0 -o eth1 -j REJECT iptables -A FORWARD -i eth0 -o eth2 -j REJECT This configuration means that users will be forwarded through a modem/router with a public address - this is all well and good for most purposes, and in the main it doesn't matter that all computers are hidden behind the one public IP. However, some users need to be able to access a proxy at 192.111.222.111:8080 - and the proxy needs to identify this traffic as coming through a gateway at 129.2.2.126 - it won't respond otherwise. I tried adding a static route on our local gateway with: route add -host 192.111.222.111 gw 129.2.2.126 dev eth2 I can successfully ping 192.111.222.111 from the router. When I trace the route, it lists the 129.2.2.126 gateway, but I just get * on each of the following hops (I think this makes sense since this is just a web-proxy and requires authentication). When I try to ping this address from a host on the 129.2.2.0/25 network it fails. Should I do this in the iptables chain instead? How would I configure this routing?

  Read the article

• IPTables forward from only one ip on my server

  - by user1307079

  I was able to get my server to forward connections on a certain port to a different IP, but when I add -d to specify an IP to froward from, It does not work. This is what I am trying, iptables -t nat -A PREROUTING -d 173.208.230.107 -p tcp --dport 80 iptables -t nat -nvL-j DNAT --to-destination 38.105.20.226:80. It works fine without the -d. Here is my ifconfig dump: em1 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.106 Bcast:173.208.230.111 Mask:255.255.255.248 inet6 addr: fe80::2a0:d1ff:feed:d054/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:100058 errors:0 dropped:0 overruns:0 frame:0 TX packets:18941701 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:12779711 (12.1 MiB) TX bytes:825498499 (787.2 MiB) Memory:fbde0000-fbe00000 em1:9 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.107 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:10 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.108 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:11 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.109 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:12 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.110 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

  Read the article

• Apache with multiple domains, single IP, VirtualHost is catching the wrong traffic

  - by apuschak

  I have a SOAP web service I am providing on a apache web server. There are 6 different clients (IPs) that request data and 3 of them are hitting the wrong domain. I am trying to find a way to log which domain name the requests are coming from. Details: ServerA is the primary ServerB is the backup domain1.com - the domain the web service is on domain2.com - a seperate domain that server seperate content on ServerB ServerA is standalone for now with its own IP and DNS from domain1.com. This works for everyone. ServerB is a backup for the web service, but it already hosts domain2.com. I added entries into the apache configuration file like: <VirtualHost *:443> ServerName domain2.com DocumentRoot /var/www/html/ CustomLog logs/access_log_domain2443 common ErrorLog logs/ssl_error_log_domain2443 LogLevel debug SSLEngine on ... etc SSL directives ... </VirtualHost> I have these for both 80 and 443 for domain1 and domain2 with domain1 being second. The problem is when we switch DNS for domain1 from ServerA to ServerB, 3 out of the 6 clients show up in the debug logs as hitting domain2.com instead of domain1.com and fail their web service request because domain2.com is first in the apache configuration file and catching all requests that don't match other virtualhosts, namely domain1.com. I don't know if they are hitting www.domain1.com, domain1.com (although I added entries for both) or using the external IP address or something else. Is there a way to see which URL they are hitting not just the page request or someother way to see why the first domain is catching traffic meant for the second listed domain? In the meantime, I've put domain1.com higher in the apache configuration than domain2.com. Now it catches the requests for all clients and works, however I don't know what it is catching and would like to make domain2.com the first entry again with a correct entry for domain1.com, for however they are hitting it. Thank you for your help! Andrew

  Read the article

• Connecting to network device behind NAT from local LAN using the external port and IP

  - by lumbric

  I noticed at several different LANs connected to the Internet through a NAT the following phenomena. There is a server in the LAN and there is a port forwarding to reach this server also from outside the LAN through the NAT. E.g. consider a LAN with the address 192.168.0.* and a SSH server at 192.168.0.2 with port 22 and a forwarding from port 2222 at the NAT 192.168.0.1 to 192.168.0.2:22. If the NAT's external IP is 44.33.22.11, one can connect to the SSH server through 44.33.22.11:2222. Surprisingly this works only from outside the LAN. If one tries to connect to 44.33.22.11:2222 from behind the NAT, there is no answer. Of course one could simply use 192.168.0.2:22, but often it is simpler to use the external IP. The typical use case for me is the configuration on a laptop computer. Usually the user uses any arbitrary Internet connection to connect to his home or office server, but sometimes he will use also the LAN to connect to it and it would be annoying to have to different configurations or bookmarks. Why does it fail to connect from inside the LAN? Is there any good work around?

  Read the article

• Strange Domain name under the same IP Address

  - by Mike Chip

  There's something really weird happening in my server. But first things first: I wanted to have my website and chose the domain name "myowndomain.com", Now on my domain registrar I point "myowndomain.com" to the address of my recently setup VPS, let's say 50.50.50.50 So I installed everything I needed to run my website, and I started to notice strange queries coming from different IP Addresses. Like these [client 123.123.123.123] File does not exist: /var/www/html/api, referer: http://www.strangedomain.com/api/manyou/my.php [client 456.456.456.456] File does not exist: /var/www/html/api, referer: http://www.strangedomain.com/api/manyou/my.php or like this (Really a long line, I cut some things) GET /?s=vod-show-id-22-area-%E5%85%B6%E4%BB%96-language-%E9%9F%A9%E8%AF%AD.html HTTP/1.1" 301 295 "http://v.strangedomain.com/?s=vod-s ...[cut]... spider" That above is happening the most. The 'strangedomain.com' returns the same IP address of my VPS which my website is hosted on. The whois of such domain shows it's registered to a chinese. But the street name didn't look so right (like a huge single word), so I think all of that info might be fake, but still might be a chinese. I also noticed that all 'clients' trying to access the 'strangedomain.com' is coming from china. If I type in the browser 'strangedomain.com', I see my website. I'm worried, because my website is actually an e-commerce. I don't know if 'strangedomain.com' WAS a website on 50.50.50.50 in the not so far past, or if it's something else.

  Read the article

• Cisco ASA 5505 network route for static IP hosts

  - by TheCapn

  I've configured my internal VLAN using the most basic settings where ports 1-7 are assigned from a pool of addresses in the range 192.168.15.5 - 192.168.15.36. These hosts are given access to the internet and it works great. What I'm trying to set up now is allowing users who are connected to the device and specify their IP (say I connect and request 192.168.15.45) are given internet access and can still work alongside DHCP hosts. Those with a DHCP assigned address are blocked from the internet. Mostly the issue resides in that I am very new to working with the device. I feel that the solution is easy but I'm not looking in the right spots and don't have the correct terminology down to google it. Do I need to define access control lists? Group policies? a new VLAN? The rules that are set up seem to be specific to the entire /24 subnet but when I request a static IP outside of the DHCP range I get blocked from other hosts and the internet.

  Read the article

• 2 Web Servers, 2 Domains, 1 WAN IP configuration

  - by Tillman32

  The Problem: I have 2 domains, 2 web servers, 1 WAN IP. This is on a home network, so I don't have any crazy router or anything with the right tools, at least I don't think I do. I have a Dlink DIR-655 router. I need to be able to forward the website to the right box. 1 server is hosting www.site1.com, and the other should be hosting, www.site2.com. I forwarded the domain, to a port that is forwarded to that box. wanip:1235, 1235 is then forwarded to the internal IP of site2's server. But when I go to www.site2.com I get the 404 page of www.site1.com. I need www.site2.com to go to the right server. Is this something I can do in the virtual hosts of www.site1.com or is it something else. Also, if this isn't entirely possible, or if its a big process, I can just move www.site1.com to the www.site2.com's server, and use virtual hosts, that is an option that I would be okay with.

  Read the article

< Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >